DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS Hi Q Series Class 1, NP0 16 V TO 250 V 0.2 pF to 100 pF Product Specification - January 9, 2015 V.11 RoHS compliant & Halogen Free Product specification Surface-Mount Ceramic Multilayer Capacitors SCOPE This specification describes NP0 series chip capacitors with leadfree terminations. APPLICATIONS Consumer electronics for example - Tuners - Television receivers - All types of cameras Telecommunications Data processing HiQ NP0 16 V to 250 V 2 12 ORDERING INFORMATION - GLOBAL PART NUMBER, PHYCOMP CTC & 12NC All part numbers are identified by the series, size, tolerance, TC material, packing style, voltage, process code, termination and capacitance value. YAGEO/ PHYCOMP BRAND ordering code GLOBAL PART NUMBER (PREFERRED ) CQ XXXX X X (1) NPO (2) (3) X BN XXX (4) (5) (1) SIZE - INCH BASED (METRIC) 0201 (0603) 0402 (1005) 0603 (1608) FEATURES Supplied in tape on reel Nickel-barrier end termination RoHS compliant Halogen Free compliant 0805 (2012) (2) TOLERANCE 0.2pF to 2.0pF A = 0.05 pF B = 0.1 pF C = 0.25 pF 2.1pF to 4.9pF A = 0.05 pF (by request) B = 0.1 pF C = 0.25 pF D = 0.5 pF 5.0pF to 9.9pF B = 0.1 pF C = 0.25 pF D = 0.5 pF 10pF and over F = 1% G = 2% J = 5% (3) PACKING STYLE R = Paper/PE taping reel; Reel 7 inch P = Paper/PE taping reel; Reel 13 inch (4) RATED VOLTAGE 7 = 16 V 0=100V 8 = 25 V A=200V 9 = 50 V Y=250V (5) CAPACITANCE VALUE 2 significant digits + number of zeros The 3rd digit signifies the multiplying factor, and letter R is decimal point Example: 121 = 12 x 101 = 120 pF www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors CONSTRUCTION The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a high capacitance per unit volume. The inner electrodes are connected to the two end terminations and finally covered with a layer of plated tin (NiSn). The terminations are lead-free. A cross section of the structure is shown in Fig.1. HiQ 16 V to 250 V NP0 3 12 terminations electrodes MLB457 ceramic material Fig. 1 Surface mounted multilayer ceramic capacitor construction OUTLINES DIMENSION For dimension see Table 1 Table 1 For outlines see fig. 2 TYPE L1 (mm) W (mm) 0201 0402 0.6 0.03 0.3 0.03 1.0 0.05 0.5 0.05 0603 1.6 0.10 0.8 0.10 0805 2.0 0.20 1.25 0.20 T (MM) Refer to table 2 to 5 L2 / L3 (mm) L4 (mm) min. max. min. 0.10 0.20 0.20 0.20 0.30 0.40 0.20 0.60 0.40 0.25 0.75 0.55 Fig. 2 Surface mounted multilayer ceramic capacitor dimension www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V 4 12 CAPACITANCE RANGE & THICKNESS FOR NP0 Table 2 Sizes from 0201 to 0402 CAP. 0201 0402 25 V 50 V CAP. 0.2 pF 2.6 pF 0.3 pF 2.7 pF 0.4 pF 2.8 pF 0.5 pF 2.9 pF 0.6 pF 3.0 pF 0.7 pF 3.1 pF 0.8 pF 3.2 pF 0.9 pF 3.3 pF 1.0 pF 3.4 pF 1.1 pF 3.5 pF 1.2 pF 3.6 pF 1.3 pF 1.4 pF 0.30.03 0.50.05 3.8 pF 3.9 pF 1.6 pF 4.0 pF 1.7 pF 4.1 pF 1.8 pF 4.2 pF 1.9 pF 4.3 pF 2.0 pF 4.4 pF 2.1 pF 4.5 pF 2.2 pF 4.6 pF 2.3 pF 4.7 pF 2.4 pF 4.8 pF 2.5 pF 4.9 pF 8mm 0402 25 V 50 V 0.30.03 0.50.05 3.7 pF 1.5 pF Tape width 0201 5.0 pF Tape width 8mm NOTE 1. Values in shaded cells indicate thickness class in mm www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V 5 12 CAPACITANCE RANGE & THICKNESS FOR NP0 Table 3 Sizes from 0201 to 0402 CAP. 0201 0402 25 V 50 V CAP. 5.1 pF 7.8 pF 5.2 pF 7.9 pF 5.3 pF 8.0 pF 5.4 pF 8.1 pF 5.5 pF 8.2 pF 5.6 pF 8.3 pF 5.7 pF 8.4 pF 5.8 pF 8.5 pF 5.9 pF 8.6 pF 6.0 pF 8.7 pF 6.1 pF 8.8 pF 6.2 pF 8.9 pF 6.3 pF 9.0 pF 6.4 pF 0.30.03 0.50.05 9.2 pF 6.6 pF 9.3 pF 6.7 pF 9.4 pF 6.8 pF 9.5 pF 6.9 pF 9.6 pF 7.0 pF 9.7 pF 7.1 pF 9.8 pF 7.2 pF 9.9 pF 7.3 pF 10 pF 7.4 pF 12 pF 7.5 pF 15 pF 7.6 pF 18 pF 7.7 pF 22 pF 8mm 0402 25 V 50 V 0.30.03 9.1 pF 6.5 pF Tape width 0201 0.50.05 27 pF 33 pF Tape width 8mm NOTE 2. Values in shaded cells indicate thickness class in mm www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V 6 12 CAPACITANCE RANGE & THICKNESS FOR NP0 Table 4 Sizes from 0603 to 0805 0603 CAP. 0805 25 V 50 V 100V 200V 250V 0.80.1 0.80.1 0.80.1 0.80.1 0.80.1 25 V 50 V 100V 200V 250V 0.60.1 0.60.1 0.60.1 0.60.1 0.60.1 0.22 pF 0.47 pF 0.56 pF 0.68 pF 0.82 pF 1.0 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF Tape width 8mm NOTE 1. Values in shaded cells indicate thickness class in mm www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V 7 12 THICKNESS CLASSES AND PACKING QUANTITY Table 5 SIZE CODE O180 MM / 7 INCH O330 MM / 13 INCH THICKNESS CLASSIFICATION TAPE WIDTH QUANTITY PER REEL Paper/PE Blister Paper/PE Blister QUANTITY PER BULK CASE 0201 0.3 0.03 mm 8 mm 15,000 --- 50,000 --- --- 0402 0.5 0.05 mm 8 mm 10,000 --- 50,000 --- --- 0603 0.8 0.1 mm 8 mm 4,000 --- 15,000 --- --- 0805 0.6 0.1 mm 8 mm 4,000 --- 20,000 --- --- ELECTRICAL CHARACTERISTICS NP0 DIELECTRIC CAPACITORS; NISN TERMINATIONS Unless otherwise stated all electrical values apply at an ambient temperature of 201 C, an atmospheric pressure of 86 to 106 kPa, and a relative humidity of 63 to 67%. Table 6 VALUE DESCRIPTION Capacitance range 0.2 pF to 100 pF Capacitance tolerance C < 10 pF 0.05 pF, 0.1 pF, 0.25 pF, 0.5 pF C 10 pF 2%, 5% C < 30 pF Q ( 400 + 20C ) Q value C: pF C 30 pF Q 1000 Insulation resistance after 1 minute at Ur (DC) Rins 10 G or Rins x Cr 500 seconds whichever is less Maximum capacitance change as a function of temperature (temperature characteristic/coefficient): 30 ppm/C Operating temperature range: -55 C to +125 C SOLDERING RECOMMENDATION Table 7 SOLDERING METHOD SIZE 0201 0402 0603 0805 Reflow O O O O Wave --- --- O O www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V 8 12 TESTS AND REQUIREMENTS Table 8 Test procedures and requirements TEST TEST METHOD PROCEDURE REQUIREMENTS Mounting IEC 6038421/22 4.3 The capacitors may be mounted on printed-circuit boards or ceramic substrates No visible damage Visual inspection and dimension check 4.4 Any applicable method using x 10 magnification In accordance with specification Capacitance 4.5.1 Class 1: f = 1 MHz for C 1 nF, measuring at voltage 1 Vrms at 20 C Within specified tolerance f = 1 KHz for C > 1 nF, measuring at voltage 1 Vrms at 20 C Q value 4.5.2 Class 1: f = 1 MHz for C 1 nF , measuring at voltage 1 Vrms at 20 C In accordance with specification f = 1 KHz for C > 1 nF, measuring at voltage 1 Vrms at 20 C Insulation resistance 4.5.3 At Ur (DC) for 1 minute In accordance with specification www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors TEST Temperature coefficient TEST METHOD 4.6 HiQ NP0 16 V to 250 V PROCEDURE REQUIREMENTS Capacitance shall be measured by the steps shown in the following table. <General purpose series> Class1: C/C: 30ppm 9 12 The capacitance change should be measured after 5 min at each specified temperature stage. Class2: X7R: C/C: 15% Step Temperature() Y5V: C/C: 22~-82% a 252 <High Capacitance series> b Lower temperature3 Class2: X7R/X5R: C/C: 15% c 252 Y5V: C/C: 22~-82% d Upper Temperature2 e 252 (1) Class I Temperature Coefficient shall be calculated from the formula as below Temp, Coefficient = C2 - C1 x106 [ppm/] C1xT C1: Capacitance at step c C2: Capacitance at 125 T: 100(=125-25) (2) Class II Capacitance Change shall be calculated from the formula as below C = C2 - C1 x 100% C1 C1: Capacitance at step c C2: Capacitance at step b or d Adhesion 4.7 A force applied for 10 seconds to the line joining the terminations and in a plane parallel to the substrate Force size 0603: 5N size = 0402: 2.5N size = 0201: 1N Bond strength of plating on end face 4.8 Mounting in accordance with IEC 60384-22 paragraph 4.3 No visible damage Conditions: bending 1 mm at a rate of 1 mm/s, radius jig 340 mm <General purpose series> C/C Class 1: NP0: within 1% or 0.5 pF whichever is greater ESR Measuring frequency: 1 0.2GHz at room temperature. 0.2pF C 1pF :350m max 1pF < C 5pF :300m max 5pF < C 10pF :250m max Measuring frequency: 500 50MHz at room temperature. 10pF < C 100pF :400m max www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors TEST TEST METHOD Resistance to IEC 60384soldering heat 21/22 4.9 HiQ NP0 16 V to 250 V 10 12 PROCEDURE REQUIREMENTS Precondition: 150 +0/-10 C for 1 hour, then keep for 24 1 hours at room temperature Dissolution of the end face plating shall not exceed 25% of the length of the edge concerned Preheating: for size 1206: 120 C to 150 C for 1 minute Preheating: for size >1206: 100 C to 120 C for 1 minute and 170 C to 200 C for 1 minute <General purpose series> C/C Solder bath temperature: 260 5 C Class 1: NP0: within 0.5% or 0.5 pF whichever is greater Dipping time: 10 0.5 seconds Recovery time: 24 2 hours D.F. within initial specified value Rins within initial specified value Solderability 4.10 Preheated the temperature of 80 C to 140 C and maintained for 30 seconds to 60 seconds. The solder should cover over 95% of the critical area of each termination Test conditions for lead containing solder alloy Temperature: 235 5 C Dipping time: 2 0.2 seconds Depth of immersion: 10 mm Alloy Composition: 60/40 Sn/Pb Number of immersions: 1 Test conditions for lead-free containing solder alloy Temperature: 245 5 C Dipping time: 3 0.3 seconds Depth of immersion: 10 mm Alloy Composition: SAC305 Number of immersions: 1 Rapid change of temperature 4.11 Preconditioning; 150 +0/-10 C for 1 hour, then keep for 24 1 hours at room temperature 5 cycles with following detail: 30 minutes at lower category temperature 30 minutes at upper category temperature No visual damage <General purpose series> C/C Class 1: NP0: within 1% or 1 pF whichever is greater Recovery time 24 2 hours D.F. meet initial specified value Rins meet initial specified value www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V TEST TEST METHOD PROCEDURE REQUIREMENTS Damp heat with Ur load IEC 6038421/22 1. Preconditioning, class 2 only: No visual damage after recovery 4.13 150 +0/-10 C /1 hour, then keep for 24 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Damp heat test: 500 12 hours at 40 2 C; 90 to 95% R.H. 1.0 Ur applied 4. Recovery: Class 1: 6 to 24 hours 5. Final measure: C, D, IR P.S. If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to "IEC 60384 4.1" and then the requirement shall be met. 4.14 Endurance 1. Preconditioning, class 2 only: 150 +0/-10 C /1 hour, then keep for 24 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Endurance test: Temperature: NP0: 125 C Specified stress voltage applied for 1,000 hours: Applied 2.0 x Ur for general product. Voltage proof IEC 60384-1 4.6 Class 1: NP0: within 2% or 1 pF whichever is greater D.F. Class 1: NP0: 2 x specified value Rins Class 1: NP0: 2,500 M or Rins x Cr 25s whichever is less No visual damage <General purpose series> C/C Class1: NP0: within 2% or 1 pF whichever is greater D.F. Class1: NP0: 2 x specified value 5. Final measure: C, D, IR Rins Specified stress voltage applied for 1 minute Ur 100 V: series applied 2.5 Ur 100 V < Ur 200 V series applied (1.5 Ur + 100) 200 V < Ur 500 V series applied (1.3 Ur + 100) Ur > 500 V: 1.3 Ur I: 7.5 mA 12 <General purpose series> C/C 4. Recovery time: 24 2 hours P.S. If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to "IEC 60384 4.1" and then the requirement shall be met. 11 Class1: NP0: 4,000 M or Rins x Cr 40s whichever is less No breakdown or flashover www.yageo.com Jan. 9, 2015 V.11 Product specification Surface-Mount Ceramic Multilayer Capacitors HiQ NP0 16 V to 250 V 12 12 REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 11 Mar 19, 2014 - - Size update Version 10 Mar 19, 2014 - - Tests and requirements Version 9 Feb. 27, 2014 - - Tolerance update Version 8 Oct. 28, 2013 - - Rated voltage update Version 7 Oct. 09, 2013 - - Rated voltage update Version 6 Jun. 24, 2013 - - Tolerance update Version 5 Apr. 15, 2013 - - Tolerance update Version 4 Mar. 28, 2013 - - Capacitance range & thickness update Version 3 Feb. 07, 2013 - - Capacitance range & thickness update Version 2 Dec. 25, 2012 - - Capacitance range & thickness update Version 1 Dec. 03, 2012 - - Capacitance range & thickness update Version 0 Nov. 23, 2012 - - New datasheet for HiQ NP0 series with RoHS compliant www.yageo.com Jan. 9, 2015 V.11 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Yageo: CQ0201ARNPO8BN1R0 CQ0402ARNPO9BN2R0 CQ0402BRNPO9BN1R2 CQ0201BRNPO8BN2R0 CQ0402JRNPO9BN120 CQ0201BRNPO8BN3R9 CQ0402ARNPO9BNR20 CQ0402BRNPO9BN2R2 CQ0402BRNPO9BNR20 CQ0402CRNPO9BN7R0 CQ0402BRNPO9BN3R3 CQ0201CRNPO8BN5R0 CQ0402BRNPO9BN7R0 CQ0402BRNPO9BN4R0 CQ0201ARNPO8BN2R7 CQ0402BRNPO9BN8R2 CQ0201BRNPO8BN1R5 CQ0201ARNPO8BNR70 CQ0402ARNPO9BNR50 CQ0201CRNPO8BN6R2 CQ0201ARNPO8BN4R3 CQ0402ARNPO9BNR80 CQ0201CRNPO8BN9R1 CQ0201BRNPO8BN7R5 CQ0201ARNPO8BNR40 CQ0402CRNPO9BN9R0 CQ0201BRNPO8BN6R0 CQ0201ARNPO8BN1R3 CQ0201ARNPO8BN3R6 CQ0201BRNPO8BN2R7 CQ0402GRNPO9BN120 CQ0201BRNPO8BN9R0 CQ0201BRNPO8BN4R7 CQ0201BRNPO8BN1R0 CQ0402JRNPO9BN220 CQ0201BRNPO8BNR30 CQ0402ARNPO9BN2R7 CQ0201CRNPO8BN9R0 CQ0201BRNPO8BN7R0 CQ0402BRNPO9BNR90 CQ0402BRNPO9BN5R6 CQ0402ARNPO9BN1R0 CQ0402BRNPO9BN1R6 CQ0402CRNPO9BN6R0 CQ0201BRNPO8BN1R3 CQ0402BRNPO9BN3R0 CQ0402BRNPO9BN6R8 CQ0402ARNPO9BN1R8 CQ0402BRNPO9BNR50 CQ0402ARNPO9BN3R6 CQ0402ARNPO9BN4R7 CQ0402ARNPO9BNR40 CQ0201JRNPO8BN100 CQ0402JRNPO9BN180 CQ0201ARNPO8BN3R3 CQ0402ARNPO9BN2R4 CQ0402GRNPO9BN100 CQ0402CRNPO9BN8R2 CQ0402CRNPO9BN5R6 CQ0201ARNPO8BN2R4 CQ0402JRNPO9BN100 CQ0402BRNPO9BN3R9 CQ0402BRNPO9BN1R5 CQ0201ARNPO8BNR30 CQ0402GRNPO9BN220 CQ0201ARNPO8BNR60 CQ0402BRNPO9BN8R0 CQ0201BRNPO8BNR20 CQ0201BRNPO8BN8R2 CQ0201BRNPO8BN6R8 CQ0201ARNPO8BN1R6 CQ0402JRNPO9BN330 CQ0201BRNPO8BNR60 CQ0402ARNPO9BN1R3 CQ0201BRNPO8BN3R6 CQ0201ARNPO8BN1R2 CQ0201BRNPO8BN4R3 CQ0402BRNPO9BN5R0 CQ0201CRNPO8BN7R0 CQ0201ARNPO8BN4R0 CQ0201CRNPO8BN7R5 CQ0402BRNPO9BN1R1 CQ0201ARNPO8BN1R8 CQ0201CRNPO8BN6R0 CQ0201BRNPO8BNR90 CQ0201BRNPO8BN1R8 CQ0402BRNPO9BN9R1 CQ0402BRNPO9BNR80 CQ0201ARNPO8BNR90 CQ0402BRNPO9BN2R7 CQ0402BRNPO9BN6R2 CQ0201BRNPO8BN2R4 CQ0402BRNPO9BNR40 CQ0402ARNPO9BNR70 CQ0201BRNPO8BN5R6 CQ0402CRNPO9BN6R8 CQ0402BRNPO9BN7R5 CQ0201ARNPO8BNR50 CQ0201ARNPO8BNR20 CQ0201BRNPO8BNR80