PE43713
Product Specification
UltraCMOS® RF Digital Step Attenuator, 9 kHz–6 GHz
©2017, Peregrine Semiconductor Corporation. All rights reserved. • Headquarters: 9380 Carroll Park Drive, San Diego, CA, 92121
Product Specification DOC-84877-2 – (1/2018)
www.psemi.com
Features
• Flexible attenuation steps of 0.25 dB, 0.5 dB and
1 dB up to 31.75 dB
• Glitch-less attenuation state transitions
• Monotonicity: 0.25 dB up to 4 GHz, 0.5 dB up to
5 GHz and 1 dB up to 6 GHz
• Extended +105 °C operating temperature
• Parallel and Serial programming interfaces with
Serial Addressability
• Packaging—32-lead 5 × 5 mm QFN
Applications
• Test and measurement (T&M)
• General purpose RF attenuator
Product Description
The PE43713 is a 50Ω, HaRP™ technology-enhanced, 7-bit RF digital step attenuator (DSA) that supports a
broad frequency range from 9 kHz to 6 GHz. It features glitch-less attenuation state transitions, supports 1.8V
control voltage and includes an extended operating temperature range to +105 °C and optional VSS_EXT bypass
mode to improve spurious performance, making this device ideal for test and measurement (T&M).
The PE43713 is a pin-compatible upgraded version of the PE43703. An integrated digital control interface
supports both Serial Addressable and Parallel programming of the attenuation, including the capability to
program an initial attenuation state at power-up.
The PE43713 covers a 31.75 dB attenu ation range in 0.25 dB, 0.5 dB and 1dB steps. It is capable of maintaining
0.25 dB monotonicity through 4 GHz, 0.50 dB monotonicity through 5 GHz and 1 dB monotonicity through 6
GHz. In addition, no external blocking capacitors are required if 0 VDC is present on the RF ports.
The PE43713 is manufactured on Peregrine’s UltraCMOS® process, a patented variation of silicon-on-insulator
(SOI) technology on a sapphire substrate.
Figure 1 • PE43713 Functional Diagram
×7
RF
Input
RF
Output
Control Logic Interface
Switched Attenuator Array
V
SS_EXT
P/SA0 A1 A2
Parallel
Control
Serial In
CLK
(optional)
LE
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 2 DOC-84877-2 – (1/2018)
www.psemi.com
Peregrine’ s HaRP tech nology enhancements d eliver high linea rity and excellent ha rmonics performance. It is an
innovative feature of the UltraCMOS process, offering the performance of GaAs with the economy and
integration of conventional CMOS.
Optional External VSS Control
For proper operation, the VSS_EXT control pin must be grounded or tied to the VSS voltage specified in Table 2.
When the VSS_EXT control pin is grounded, FETs in the switch are biased with an internal negative voltage
generator. For applications that require the lowest possible spur performance, VSS_EXT can be applied externally
to bypass the internal negative voltage generator.
Absolute Maximum Ratings
Exceeding absolute maximum ratings listed in Table 1 may cause permanent damage. Operation should be
restricted to the limits in Table 2. Operation between operating range maximum and absolute maximum for
extended periods may reduce reliability.
ESD Precautions
When handling this UltraCMOS device, observe the same precautions as with any other ESD-sensitive devices.
Although this device contains circui try to protect it from damage due to ESD, precautions should be taken to
avoid exceeding the rating specified in Table 1.
Latch-up Immunity
Unlike conventional CMOS devices, UltraCMOS devices are immune to latch-up.
Table 1 • Absolute Maximum Ratings for PE43713
Parameter/Condition Min Max Unit
Supply voltage, VDD –0.3 5.5 V
Digital input voltage –0.3 3.6 V
RF input power, 50Ω
9 kHz–48 MHz
>48 MHz–6 GHz Figure 5
+31 dBm
dBm
Storage temperature range –65 +150 °C
ESD voltage HBM, all pins(1) 3000 V
ESD voltage CDM, all pins(2) 1000 V
Notes:
1) Human body mo de l ( MIL –STD 8 83 Me tho d 301 5).
2) Charged device mo del ( JEDEC JESD22–C1 01 ).
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 3
www.psemi.com
Recommended Operating Conditions
Table 2 lists the recommending operating condition for the PE43713. Devices should not be operated outside
the recommended operating conditions listed below.
Table 2 • Recommended Operating Condition for PE43713
Parameter Min Typ Max Unit
Normal mode, VSS_EXT = 0V(1)
Supply voltage, VDD 2.3 5.5 V
Supply current, IDD 150 200 µA
Bypass mode, VSS_EXT = –3.4V(2)
Supply voltage, VDD (VDD ≥ 3.4V see Table 3 for full spec compliance) 2.7 3.4 5.5 V
Supply current, IDD 50 80 µA
Negative supply voltage, VSS_EXT –3.6 –2.4 V
Negative supply current, ISS –40 –16 µA
Normal or bypass mode
Digital input high 1.17 3.6 V
Digital input low –0.3 0.6 V
Digital input current 17.5 µA
RF input power, CW(3)
9 kHz–48 MHz
>48 MHz–6 GHz Figure 5
+23 dBm
dBm
RF input power, pulsed(4)
9 kHz–48 MHz
>48 MHz–6 GHz Figure 5
+28 dBm
dBm
Operating temperature range –40 +25 +105 °C
Notes:
1) Normal mod e: con nect V SS_EXT (pin 20) to GN D (V SS_EXT = 0V) to ena ble int erna l ne ga tive volta ge g ene r ator.
2) Bypass mode: use VSS_EXT (pin 20) to bypass and disable inte rnal negat ive voltage ge nera tor.
3) 100% duty cycle, all bands, 50Ω.
4) Pulsed, 5% duty cycle of 4620 µs period, 50Ω.
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 4 DOC-84877-2 – (1/2018)
www.psemi.com
Electrical Specifications
Table 3 provides the PE43713 key electrical specifications at 25 °C, RF1 = RFIN, RF2 = RFOUT (ZS = ZL = 50Ω),
unless otherwise specified. Normal mode(1) is at VDD = 3.3V and VSS_EXT = 0V. Bypass mode(2) is at VDD = 3.4V
and VSS_EXT = –3.4V.
Table 3 • PE43713 Electrical Specifications
Parameter Condition Frequency Min Typ Max Unit
Operating frequency 9 kHz 6 GHz As
shown
Attenuatio n ra ng e 0.25 dB step
0.5 dB step
1 dB step
0–31.75
0–31.50
0–31.00
dB
dB
dB
Insertion loss
9 kHz–1.0 GHz
1.0–2.2 GHz
2.2–4.0 GHz
4.0–6.0 GHz
1.3
1.6
1.95
2.45
1.5
1.85
2.4
2.8
dB
dB
dB
dB
Attenuation error
0.25 dB step
0–8 dB 9 kHz–2.2 GHz ±(0.20 + 1.5% of
attenuation setting) dB
8.25–31.75 dB 9 kHz–2.2 GHz ±(0.20 + 2.0% of
attenuation setting) dB
0–31.75 dB >2.2–3.0 GHz ±(0.15 + 3.0% of
attenuation setting) dB
0–31.75 dB >3.0–4.0 GHz ±(0.25 + 3.5% of
attenuation setting) dB
0.5 dB step
0–8 dB 9 kHz–2.2 GHz ±(0.20 + 1.5% of
attenuation setting) dB
8.5–31.5 dB 9 kHz–2.2 GHz ±(0.20 + 2.0% of
attenuation setting) dB
0–31.5 dB >2.2–3.0 GHz ±(0.15 + 3.0% of
attenuation setting) dB
0–31.5 dB >3.0–5.0 GHz ±(0.25 + 5.0% of
attenuation setting) dB
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 5
www.psemi.com
Attenuation error
1 dB step
0–8 dB 9 kHz–2.2 GHz ±(0.20 + 1.5% of
attenuation setting) dB
9–31 dB 9 kHz–2.2 GHz ±(0.20 + 2.0% of
attenuation setting) dB
0–31 dB >2.2–3.0 GHz ±(0.1 5 + 3.0% of
attenuation setting) dB
0–31 dB >3.0–5.0 GHz ±(0.2 5 + 5.0% of
attenuation setting) dB
0–31 dB >5.0–6.0 GHz ±(0.2 5 + 5.0% of
attenuation setting) dB
Return loss Input port 9 kHz–6 GHz 18 dB
Output port 9 kHz–4 GHz
4–6 GHz 13
15 dB
dB
Relative phase All states 9 kHz–4 GHz
4–6 GHz 27
42 deg
deg
Input 0.1dB compression
point(3) 48 MHz–6 GHz 31 dBm
Input IP3 Two tones at +18 dBm, 20 MHz
spacing 4 GHz
6 GHz 57
56 dBm
dBm
RF Trise/Tfall 10%/90% RF 200 ns
Settling time RF settled to within 0.05 dB of final
value 1.6 µs
Switching time 50% CTRL to 90% or 10% RF 275 ns
Attenuation transient
(envelope) 2 GHz 0.3 dB
Notes:
1) Normal mod e: con nect V SS_EXT (pin 20) to GND (VSS_EXT = 0V) to e nab le intern al ne gat ive vo lta ge ge nera tor.
2) Bypass mode: use VSS_EXT (pin 20) to b ypass an d d isab le in te rn al n eg ative vo lt ag e gen erat or.
3) The input 0.1 dB compre ssion poin t is a linearit y figure of merit. Re fer to Table 2 for the operating RF inp ut powe r (50Ω).
Table 3 • PE43713 Electrical Specifications (Cont.)
Parameter Condition Frequency Min Typ Max Unit
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 6 DOC-84877-2 – (1/2018)
www.psemi.com
Switching Frequency
The PE43713 has a maximum 25 kHz switching rate
in normal mode (pin 20 tied to ground). A faster
switching rate is available in bypass mode (pin 20 tied
to VSS_EXT). The rate at which the PE43713 can be
switched is then limited to the switching time as
specified in Table 3.
Switching frequency is defined to be the speed at
which the DSA can be toggled across attenuation
states. Switching time is the time duration between
the point the control signal reaches 50% of the final
value and the point the output signal reaches within
10% or 90% of its target value.
Spur-free Performance
The typical spurious performance of the PE43713 in
normal mode is –130 dBm (pin 20 tied to ground). If
spur-free performance is desired, the internal
negative voltage generator can be disabled by
applying a negative voltage to VSS_EXT (pin 20).
Glitch-less Attenuation State Transitions
The PE43713 features a novel architecture to provide
the best-in-class glitch-less transition behavior when
changing attenuation states. When RF input power is
applied, the output power spikes are greatly reduced
(≤0.3 dB) during attenuation state changes when
comparing to previous generations of DSAs.
Truth Tables
Table 4–Table 6 provide the truth tables for the
PE43713.
Table 4 • Parallel Truth Table
Parallel Control Setting Attenuation
Setting
RF1–RF2
D6 D5 D4 D3 D2 D1 D0
L L L L L L L Reference IL
L L L L L L H 0.25 dB
L L L L L H L 0.5 dB
LLLLHLL 1 dB
LLLHLLL 2 dB
LLHLLLL 4 dB
LHLLLLL 8 dB
H L L L L L L 16 dB
HHHHHHH 31.75 dB
Table 5 • Serial Address Word Truth Table
Address Word Address
Setting
A7
(MSB) A6 A5 A4 A3 A2 A1 A0
X X X X X L L L 000
X X X X X L L H 001
X X X X X L H L 010
XXXXXLHH 011
X X X X X H L L 100
X X X X X H L H 101
XXXXXHHL 110
X XXXXHHH 111
Table 6 • Serial Attenuation Word Truth Table
Attenuation Word Attenuation
Setting
RF1–RF2
D7 D6 D5 D4 D3 D2 D1 D0
(LSB)
LLLLLLL L Reference IL
LLLLLLL H 0.25 dB
LLLLLLH L 0.5 dB
LLLLLHL L 1 dB
LLLLHLL L 2 dB
LLLHLLL L 4 dB
LLHLLLL L 8 dB
LHLLLLL L 16 dB
L H H H H H H H 31.75 dB
Table 4 • Parallel Truth Table (Cont.)
Parallel Control Setting Attenuation
Setting
RF1–RF2
D6 D5 D4 D3 D2 D1 D0
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 7
www.psemi.com
Serial Addressable Register Map
Figure 2 provides the Serial Addressable register map for the PE43713.
Figure 2 • Serial Addressable Register Map
Attenuation Word
LSB (first in) MSB (last in)
Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0
D7 D6 D5 D4 D3 D2 D1 D0
Q15 Q14 Q13 Q12 Q11 Q10 Q9 Q8
A6 A7 A5 A4 A3 A2 A1 A0
Address Word
D7 must be set to logic low
Bits can either be set to logic high or logic low
4 × 18.25 = 73
73 → 01001001
A
ddress Word: XXXXX011
A
ttenuation Word: 01001001
Serial Input: XXXXX01101001001
For example, to program the 18.25 dB state at address 3:
The attenuation word is derived directly from the value of the attenuation state. To find
the attenuation word, multiply the value of the state by four, then convert to binary.
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 8 DOC-84877-2 – (1/2018)
www.psemi.com
Programming Options
Parallel/Serial Selection
Either a Parallel or Serial addressable interface can
be used to control the PE43713. The P/S bit provides
this selection, with P/S = LOW selecting the Parallel
interface and P/S = HIGH sel ecting the Seri al
interface.
Parallel Mode Interface
The Parallel interface consists of seven CMOS-
compatible control lines that select the desired attenu-
ation state, as shown in Table 4.
The Parallel interface timing requiremen ts are defined
by Figure 4 (Parallel Interface Timing Diagram),
Table 9 (Parallel and Direct Interface AC Character-
istics) and switching time (Table 3).
For Latched Parallel programming, the Latch Enable
(LE) should be held LOW while changing attenuation
state control values then pulse LE HIGH to LOW (per
Figure 4) to latch new attenuation stat e into the
device.
For Direct Parallel programming, the LE line should
be pulled HIGH. Changing attenuation state control
values will change device state to new attenuation.
Direct mode is ideal for manual control of the device
(using hardwire, sw itches, or jumpers).
In parallel mode, Serial-In (SI) and Clock (CLK) pins
are "don't care" and may be tied to logic LOW or logic
HIGH.
Serial-Addressable Interface
The Serial-Addressable interface is a 16-bit Serial-In,
Parallel-Out shift register buffered by a transparent
latch. The 16-bits make up two words comprised of 8-
bits each. The first word is the Attenuation Word,
which controls the state of the DSA. The second word
is the Address Word, which is compared to the static
(or programmed) logical states of the A0, A1 and A2
digital inputs. If there is an address match, the DSA
changes state; otherwise its current state will remain
unchanged. Figure 3 illustrates an example timing
diagram for programming a sta te. It is required that all
Parallel control inputs be grounded when the DSA is
used in Serial -Addressa ble mode.
The Serial-Addressable interface is controlled using
three CMOS-compatible signals: SI, Clock (CLK) and
LE. The SI and CLK inputs allow data to be serially
entered into the shift register. Serial data is clocked in
LSB first.
The shift register must be loaded while LE is held
LOW to prevent the attenuator value from changing
as data is entered. The LE input should then be
toggled HIGH and brought LOW again, latching the
new data into the DSA. The Address Word truth table
is listed in Table 5. The Attenuation Word truth table
is listed in Table 6. A programming example of the
serial register is illustrated in Figure 2. The serial
timing diagram is illustrated in Figure 3.
Power-up Control Settings
The PE43713 will always initialize to the maximum
attenuation setting (31.75 dB) on power-up for both
the Serial Addressable and Latched Parallel modes of
operation and will remain in this setting until the user
latches in the next programming word. In Direct
Parallel mode, the DSA can be preset to any state
within the 31.75 dB range by pre-setting the Parallel
control pins prior to power-up. In this mode, there is a
400 µs delay between the time the DSA is powered-
up to the time the desired state is set. During this
power-up delay, the device attenuates to the
maximum attenuation setting (31.75 dB) before
defaulting to the user defined state. If the control pi ns
are left floating in this mode during power-up, the
device will default to the minimum attenuation setting
(insertion loss state).
Dynamic operation between Serial and Parallel
programming modes is possible.
If the DSA powers up in Serial mode (P/S = HIGH), all
the Parallel control inputs DI[6:0] must be set to logic
LOW. Prior to toggling to Parallel mode, the DSA must
be programmed serially to ensure D[7] is set to logic
LOW.
If the DSA powers up in either Latched or Direct
Parallel mode, all Parallel pins DI[6:0] must be set to
logic LOW prior to toggling to Serial Addressable
mode (P/S = HIGH), and held LOW until the DSA has
been programmed serially to ensure bit D[7] is set to
logic LOW.
The sequencing is only required once on power-up.
Once completed, the DSA may be toggled between
Serial and Parallel programming modes at will.
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 9
www.psemi.com
Figure 3 • Serial Addressable Timing Diagram
Bits can either be set to logic high or logic low
Serial bit D[7] must be set to logic low
Parallel control inputsDI[6:0]
A[2] A[3] A[4] A[5] A[6] A[7]A[1]A[0]D[7]D[1] D[2] D[3] D[4] D[5] D[6]D[0]
Valid
TDISU
TASU
TPSSU
TSISU
TCLKL
TSIH
TCLKH
TDIH
TAH
TLESU
TPSIH
TLEPW
DI[6:0]
A[2:0]
P/S
SI
CLK
LE
Figure 4 • Latched-Parallel/Direct-Parallel Timing Diagram
TLEPW
TDIH
TDISU
TPSIH
Valid
DI[6:0]
LE
P/S
TPSSU
Parallel control inputsDI[6:0]
Table 7 • Latch and Clock Specifications
Latch
Enable Shift Clock Function
0↑Shift register clocked
↑XContents of shift register
transferred to attenuator
core
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 10 DOC-84877-2 – (1/2018)
www.psemi.com
Table 8 • Serial Interface AC Characteristics(*)
Parameter/Condition Min Max Unit
Serial clock frequency, FCLK 10 MHz
Serial clock HIGH time, TCLKH 30 ns
Serial clock LOW time, TCLKL 30 ns
Last Serial clock rising edge setup time to Latch Enable rising edge, TLESU 10 ns
Latch Enable minimum pulse width, TLEPW 30 ns
Serial data setup time, TSISU 10 ns
Serial data hold time, TSIH 10 ns
Parallel data setup time, TDISU 100 ns
Parallel data hold time, TDIH 100 ns
Address setup time, TASU 100 ns
Address hold time, TAH 100 ns
Parallel/Serial setup time, TPSSU 100 ns
Parallel/Serial hold time, TPSIH 100 ns
Note: * VDD = 3.3V or 5.0V, –40 °C, < TA < +105 °C, unless otherwise specified.
Table 9 • Parallel and Direct Interface AC Characteristics(*)
Parameter/Condition Min Max Unit
Latch Enable minimum pulse width, TLEPW 30 ns
Parallel data setup time, TDISU 100 ns
Parallel data hold time, TDIH 100 ns
Parallel/Serial setup time, TPSSU 100 ns
Parallel/Serial hold time, TPSIH 100 ns
Note: * VDD = 3.3V or 5.0V, –40 °C < TA < +105 °C, unless otherwise specified.
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 11
www.psemi.com
Figure 5 • Power De-rating Curve, 9 kHz–6 GHz, –40 to +105 °C Ambient, 50Ω
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
0.01 0.05 0.50 5.00 50.00 500.00 5000.00
Maximum RF Input Power (dBm)
Frequency (MHz)
P0.1 dB Compression (≥ 48 MHz) Pulsed (≥ 48 MHz)
CW & Pulsed (< 48 MHz) CW (≥ 48 MHz)
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 12 DOC-84877-2 – (1/2018)
www.psemi.com
Typical Performance Data
Figure 6–Figure 32 show the typica l p erformance data at 25 °C and V DD = 3.3 V, RF1 = RFIN, RF2 = RFOUT (ZS =
ZL = 50Ω) unless otherwise specified.
Figure 6 • Insertion Loss vs Temperature
-6
-5
-4
-3
-2
-1
0
0123456
Insertion Loss (dB)
Frequency (GHz)
-40°C 25°C 85°C 105°C
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 13
www.psemi.com
Figure 7 • Input Return Loss vs Attenuation Setting
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
0123456
Return Loss (dB)
Frequency (dB)
0 dB 0.25 dB 0.5 dB 1 dB 2 dB
4 dB 8 dB 16 dB 28 dB 31.75 dB
Figure 8 • Output Return Loss vs Attenuation Setting
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
0123456
Return Loss (dB)
Frequency (dB)
0 dB 0.25 dB 0.5 dB 1 dB 2 dB
4 dB 8 dB 16 dB 28 dB 31.75 dB
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 14 DOC-84877-2 – (1/2018)
www.psemi.com
Figure 9 • Input Return Loss for 16 dB Attenuation Setting vs Temperature
Figure 10 • Output Return Loss for 16 dB Attenuation Setting vs Temperature
-40
-35
-30
-25
-20
-15
-10
-5
0
0123456
Return Loss (dB)
Frequency (GHz)
-40°C 25°C 85°C 105°C
-25
-20
-15
-10
-5
0
0123456
Return Loss (dB)
Frequency (GHz)
-40°C 25°C 85°C 105°C
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 15
www.psemi.com
Figure 11 • Relative Phase Error vs Attenuation Setting
Figure 12 • Relative Phase Error for 31.75 dB Attenuation Setting vs Frequency
-10
0
10
20
30
40
50
60
0123456
Relative Phase Error (dB)
Frequency (GHz)
0 dB 0.25 dB 0.5 dB 1 dB 2 dB
4 dB 8 dB 16 dB 31.75 dB
0
10
20
30
40
50
60
-40C 25C 85C 105C
Relative Phase Error (deg)
Temperature (deg C)
0.9 GHz 1.8 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz 6 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 16 DOC-84877-2 – (1/2018)
www.psemi.com
Figure 13 • Attenuation Error @ 900 MHz vs Temperature
Figure 14 • Attenuation Error @ 1800 MHz vs Temperature
-0.25
0
0.25
0.5
0.75
0 4 8 12 16 20 24 28 32
Attenuation Error (dB)
Attenuation Setting (dB)
-40°C 25°C 85°C 105°C
-0.25
0
0.25
0.5
0.75
0 4 8 12 16 20 24 28 32
Attenuation Error (dB)
Attenuation Setting (dB)
-40°C 25°C 85°C 105°C
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 17
www.psemi.com
Figure 15 • Attenuation Error @ 2200 MHz vs Temperature
Figure 16 • Attenuation Error @ 3000 MHz vs Temperature
-0.25
0
0.25
0.5
0.75
0 4 8 12 16 20 24 28 32
Attenuation Error (dB)
Attenuation Setting (dB)
-40°C 25°C 85°C 105°C
-0.25
0
0.25
0.5
0.75
0 4 8 12 16 20 24 28 32
Attenuation Error (dB)
Attenuation Setting (dB)
-40°C 25°C 85°C 105°C
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 18 DOC-84877-2 – (1/2018)
www.psemi.com
Figure 17 • Attenuation Error @ 4000 MHz vs Temperature
Figure 18 • IIP3 vs Attenuation Setting
0
0.25
0.5
0.75
1
0 4 8 121620242832
Attenuation Error (dB)
Attenuation Setting (dB)
-40°C 25°C 85°C 105°C
50
55
60
65
70
3456
Input IP3 (dB)
Frequency (GHz)
0 dB 3.5 dB 7.5 dB 11 dB 14 dB
17.5 dB 21.5 dB 24.75 dB 28 dB 31.75 dB
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 19
www.psemi.com
Figure 19 • 0.25 dB Step Attenuation vs Frequency(*)
Note: * Monotonicity is held so long as step attenuation does not cross below –0.25 dB.
Figure 20 • 0.25 dB Step, Actual vs Frequency
-0.2
-0.15
-0.1
-0.05
0
0.05
0.1
0.15
0.2
0 4 8 12 16 20 24 28 32
Step Attenuation (dB)
Attenuation Setting (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz
0
5
10
15
20
25
30
35
0 4 8 121620242832
Ac t ua l At te n u a ti o n (d B )
Ideal Attenuation (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 20 DOC-84877-2 – (1/2018)
www.psemi.com
Figure 21 • 0.25 dB Major State Bit Error vs Attenuation Setting
Figure 22 • 0.25 dB Attenuation Error vs Frequency
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
01234
At tenuation Erro r (dB)
Frequency (GHz)
0.25 dB 0.5 dB 1 dB 2 dB 4 dB 8 dB 16 dB 31.75 dB
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
0 4 8 121620242832
Attenuation Error (dB)
Attenuation S etting (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 21
www.psemi.com
Figure 23 • 0.5 dB Step Attenuation vs Frequency(*)
Note: * Monotonicity is held so long as step attenuation does not cross below –0.5 dB.
Figure 24 • 0.5 dB Step, Actual vs Frequency
-0.2
-0.15
-0.1
-0.05
0
0.05
0.1
0.15
0.2
0 4 8 12 16 20 24 28 32
Step Attenuation (d B)
Attenuation Setting (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz
0
5
10
15
20
25
30
35
0 4 8 121620242832
Actual Attenuation (dB)
Ideal Attenuation (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 22 DOC-84877-2 – (1/2018)
www.psemi.com
Figure 25 • 0.5 dB Major State Bit Error vs Attenuation Setting
Figure 26 • 0.5 dB Attenuation Error vs Frequency
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
012345
Attenuation Error (dB)
Frequency (GHz)
0.5 dB 1 dB 2 dB 4 dB 8 dB 16 dB 31.5 dB
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
0 4 8 121620242832
At tenuation Erro r (dB)
Attenuation Setting (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 23
www.psemi.com
Figure 27 • 1 dB Step Attenuation vs Frequency(*)
Note: * Monotonicity is held so long as step attenuation does not cross below –1 dB.
Figure 28 • 1 dB Step, Actual vs Frequency
-0.25
-0.2
-0.15
-0.1
-0.05
0
0.05
0.1
0.15
0.2
0.25
0 4 8 121620242832
Step Attenuation (dB)
Attenuation Setting (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz 6 GHz
0
5
10
15
20
25
30
35
0 4 8 121620242832
Ac t ua l At te n u a ti o n (d B )
Ideal Attenuation (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz 6 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 24 DOC-84877-2 – (1/2018)
www.psemi.com
Figure 29 • 1 dB Major State Bit Error vs Attenuation Setting
Figure 30 • 1 dB Attenuation Error vs Frequency
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
0123456
Attenuation Error (dB)
Frequency (GHz)
1 dB 2 dB 4 dB 8 dB 16 dB 31 dB
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
0 4 8 12 16 20 24 28 32
Attenuation Error (dB)
Attenuation Setting (dB)
1 GHz 2.2 GHz 3 GHz 4 GHz 5 GHz 6 GHz
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 25
www.psemi.com
Figure 31 • Attenuation Transient (15.75–16 dB), Typical Switching Time = 275 ns
Figure 32 • Attenuation Transient (16–15.75 dB), Typical Switching Time = 275 ns
-17.0
-16.8
-16.6
-16.4
-16.2
-16.0
-15.8
-15.6
-15.4
0 400 800 1200 1600 2000 2400 2800 3200
Envelop e Power (dBm)
Time (ns)
Power (dBm)
Trigger starts ~730 ns
Glitch = 0.15 dB
-17.0
-16.8
-16.6
-16.4
-16.2
-16.0
-15.8
-15.6
-15.4
0 400 800 1200 1600 2000 2400 2800 3200
Envelop e Power (dBm)
Time (ns)
Power (dBm)
Trigger starts ~730 ns
Glitch = 0.03 dB
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 26 DOC-84877-2 – (1/2018)
www.psemi.com
Evaluation Kit
The digital step attenuator evaluation board (EVB)
was designed to ease customer evaluation of the
PE43713 digital step attenuator. The PE43713 EVB
supports Direct Parallel, Latched Parallel and Serial
modes.
Evaluation Kit Setup
Connect the EVB with the USB dongle board and USB
cable as shown in Figure 33.
Direct Parallel Programming Procedure
Direct Parallel programming is suitable for manual
operation without software programming. For manual
Direct Parallel programming, position the Parallel/
Serial (P/S) select switch to the Parallel position. The
LE switch must be switched to HIGH position.
Switches D0–D6 are SP3T switches that enable the
user to manually program the parallel bits. When D0–
D6 are toggled to the HIGH position, logic hi gh is
presented to the parallel input. When toggled to the
LOW position, logic low is presented to the parallel
input. Setting LE and D0–D6 to the EXT position
presents as OPEN, which is set for software
programming of Latched Parallel and Serial modes.
Table 4 depicts the Parallel truth table.
Latched Parallel Programming Procedure
For automated Latched Parallel programming,
connect the USB dongle board and cable that is
provided with the evaluation kit (EVK) from the USB
port of the PC to the J5 header of t he PE43713 EVB,
and set the LE and D0–D6 SP3T switches to the EXT
position. Position the Parallel/Serial (P/S) select
switch to the Parallel position. The evaluation
software is written to operate the DSA in Parallel
mode. Ensure that the software GUI is set to Latched
Parallel mode. Use the software GUI to enable the
desired attenuation state. The software GUI automati-
cally programs the DSA each time an attenuation
state is enabled.
Serial Addressable Programming Procedure
For automated Serial programming, connect the USB
dongle board and cable that is provided with the EVK
from the USB port of the PC to the J5 header of the
PE43713 EVB, and set the LE and D0–D6 SP3T
switches to the EXT position. Position the Parallel/
Serial (P/S) select switch to the Serial position. Prior
to programming, the user must define an address
setting using the HDR2 header pin. Jump the middle
column of pins on the HDR2 header (A0–A2) to the
left column of pins to set logic LOW, or jump the
middle row of pins to the right column of pins to set
logic HIGH. If the HDR2 pins are left open, then 000
becomes the default address. The software GUI is
written to operate the DSA in Serial mode. Use the
software GUI to enable each setting to the desired
attenuation state. The software GUI automatically
programs the DSA each time an attenuation state is
enabled.
Figure 33 • Evaluation Kit for PE43713
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 27
www.psemi.com
Figure 34 • Evaluation Kit Layout for PE43713
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 28 DOC-84877-2 – (1/2018)
www.psemi.com
Pin Information
This section provides pinout information for the
PE43713. Figure 35 shows the pin map of this device
for the available package. Table 10 provides a
description for each pin.
Figure 35 • Pin Configuration (Top View)
Exposed
Ground Pad
CLK
C8
C16
SI
GND
GND
GND
C2
C1
C0.5
C0.25
GND
GND
GND
A1
A2
VSS_EXT
GND
RF2
GND
GND
LE
GND
P/S
A0
GND
GND
RF1
GND
VDD
1
3
4
5
6
7
8
2
9
11
12
13
14
15
16
10
32
30
29
28
27
26
25
31
24
22
21
20
19
18
17
23
C4
GND
Pin 1 Dot
Marking
Table 10 • Pin Descriptions for PE43713
Pin No. Pin Name Description
1, 5, 6,
8–17, 19 GND Ground
2VDD Supply voltage
3P/S Serial/Parallel mode select
4 A0 Address bit A0 connection
7RF1(1) RF1 port (RF input)
18 RF2(1) RF2 port (RF output)
20 VSS_EXT(2) External VSS negative voltage con-
trol
21 A2 Address bit A2 connection
22 A1 Address bit A1 connection
23 LE Serial interface Latch Enable input
24 CLK Serial interface Clock input
25 SI Serial interface Data input
26 C16 (D6)(3) Parallel control bit, 16 dB
27 C8 (D5)(3) Parallel control bit, 8 dB
28 C4 (D4)(3) Parallel control bit, 4 dB
29 C2 (D3)(3) Parallel control bit, 2 dB
30 C1 (D2)(3) Parallel control bit, 1 dB
31 C0.5 (D1)(3) Parallel control bit, 0.5 dB
32 C0.25 (D0)(3) Parallel control bit, 0.25 dB
Pad GND Exposed pad: ground for proper
operation
Notes:
1) RF pins 7 and 1 8 m ust be a t 0 VDC . The RF pins do no t re qu ir e
DC blocking capa cit or s f or pro pe r op er at io n if t he 0 VD C
requirement is met.
2) Use VSS_EXT (pin 20) to b ypa ss an d disab le in te rn al n egat ive
voltage genera tor. Connect VSS_EXT (pin 20) to GND (VSS_EXT =
0V) to enab le in te rn al n eg ative vo lt ag e gener at or.
3) Ground C0.25, C0 .5, C1, C2, C4, C8 and C1 6 if not in use.
PE43713
UltraCMOS® RF Digital Step Attenuator
DOC-84877-2 – (1/2018) Page 29
www.psemi.com
Packaging Information
This section provides packaging data including the moisture sensitivity level, package drawing, package
marking and tape-and-reel information.
Moisture Sensitivity Level
The moisture sensitivity level rating for the PE43713 in the 32-lead 5 × 5 mm QFN package is MSL1.
Package Drawing
Top-Marking Specification
Figure 36 • Package Mechanical Drawing for 32-lead 5 × 5× 0.85 mm QFN
Figure 37 • Package Marking Specifications for PE43713
TOP VIEW BOTTOM VIEW
SIDE VIEW
RECOMMENDED LAND PATTERN
A
0.10 C
(2X)
C
0.10 C
0.05 C
SEATING PLANE
B
0.10 C
(2X)
0.10 C A B
0.05 C
ALL FEATURES
PIN #1 CORNER
5.00
5.00
0.40±0.05
(x32)
3.10±0.05
0.25±0.05
(x32)
0.50
3.50
REF
3.10±0.05
0.85±0.05
0.05
REF
0.203
REF
(x28)
CHAMFER
0.35 x 45°
0.30
(x32)
0.60
(x32)
3.15
3.15
5.40
5.40
0.50
(x28)
18
932
17 24
25
16
=
YY =
WW =
ZZZZZZZ =
Pin 1 indicator
Last two digits of assembly year
Assembly work week
Assembly lot code (maximum seven characters)
43713
YYWW
ZZZZZZZ
PE43713
UltraCMOS® RF Digital Step Attenuator
Page 30 DOC-84877-2 – (1/2018)
www.psemi.com
Tape and Reel Specification
PE43713
Figure 38 • Tape and Reel Specifications for 32-lead 5 × 5× 0.85 mm QFN
Device Orientation in Tape
Pin 1
T
K0 A0
B0
P0
P1
D1
A
Section A-A
A
Direction of Feed
D0
E
W0
P2
see note 3
see
note 1
F
see note 3
A0
B0
K0
D0
D1
E
F
P0
P1
P2
T
W0
5.25
5.25
1.10
1.50 + 0.1/ -0.0
1.5 min
1.75 ± 0.10
5.50 ± 0.05
4.00
8.00
2.00 ± 0.05
0.30 ± 0.05
12.00 ± 0.30
Notes:
1. 10 Sprocket hole pitch cumulative tolerance ±0.2
2. Camber in compliance with EIA 481
3. Pocket position relative to sprocket hole measured
as true position of pocket, not pocket hole
Dimensions are in millimeters unless otherwise specified
PE43713
Product Specification www.psemi.com DOC-84877-2 – (1/2018)
Document Categories
Advance Information
The product is in a formative or design stage. The datasheet contains design target specifications for product development. Specifications and
features may change in any manner without notice.
Preliminary Specification
The datasheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any
time without notice in order to supply the best possible product.
Product Specification
The datasheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended
changes by issuing a CNF (Customer Notification Form).
Sales Contact
For additional information, contact Sales at sales@psemi.com.
Disclaimers
The information in this document is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be
entirely at the user’s own risk. No patent rights or licenses to any circuits described in this document are implied or granted to any third party.
Peregrine’s products are not designed or intended for use in devices or system s intended for surgical implant, or in other applications intended to
support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death
might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in
such applications.
Patent Statement
Peregrine products are protected under one or more of the following U.S. patents: patents.psemi.com
Copyright and Trademark
©2017, Peregrine Semiconductor Corporation. All rights reserved. The Peregrine name, logo, UTSi and UltraCMOS are registered trademarks and
HaRP, MultiSwitch and DuNE are trademarks of Peregrine Semiconductor Corp.
Ordering Information
Table 11 lists the available ordering codes for the PE43713 as well as available shipping methods.
Table 11 • Order Codes for PE43713
Order Codes Description Packaging Shipping Method
PE43713A-Z PE43713 Digital step attenuator Green 32-lead 5 × 5 mm QFN 3000 units / T&R
PE43713B-Z PE43713 Digital step attenuator Green 32-lead 5 × 5 mm QFN 3000 units / T&R
EK43713-02 PE43713 Evaluation kit Evaluation kit 1 / Box
EK43713-03 PE43713 Evaluation kit Evaluation kit 1 / Box