PRODUCT SPECIFICATION PE83336 Military Operating Temperature Range 3.0 GHz Integer-N PLL for Low Phase Noise Applications Product Description Peregrine's PE83336 is a high performance integer-N PLL capable of frequency synthesis up to 3.0 GHz. The superior phase noise performance of the PE83336 makes it ideal for rugged military environments including: radio handsets, radar, avionics, missiles, etc. Features * 3.0 GHz operation * /10/11 dual modulus prescaler * Internal phase detector * Serial, parallel or hardwired programmable * Ultra-low phase noise * Available in 44-lead CQFJ The PE83336 features a 10/11 dual modulus prescaler, counters and a phase comparator as shown in Figure 1. Counter values are programmable through either a serial or parallel interface and can also be directly hard wired. (R) Fabricated in Peregrine's patented UTSi (Ultra Thin Silicon) CMOS technology, the PE83336, while optimized for stringent military environments, offers excellent RF performance together with the economy and integration of conventional CMOS. Figure 1. Block Diagram Fin Prescaler 10 / 11 Fin Main Counter fp 13 D(7:0) 8 Sdata Pre_en M(6:0) A(3:0) R(3:0) Primary 20-bit 20 Latch Secondary 20-bit Latch fr PEREGRINE SEMICONDUCTOR CORP. | 20 20 Phase Detector 20 PD_U PD_D 16 6 6 R Counter http://www.peregrine-semi.com fc Copyright Peregrine Semiconductor Corp. 2003 Page 1 of 14 PE83336 Product Specification VDD 2 1 GND R0 3 GND R1 4 fr R2 5 LD R3 6 Enh GND Figure 2. Pin Configuration 44 43 42 41 40 D0, M0 7 39 fc D1, M1 8 38 VDD_fc D2, M2 9 37 PD_U D3, M3 10 36 PD_D VDD 11 35 VDD VDD 12 34 Cext S_WR, D4, M4 13 33 VDD Sdata, D5, M5 14 32 Dout Sclk, D6, M6 15 31 VDD_fp FSELS, D7, Pre_en 16 30 fp GND 17 29 GND 18 19 20 21 22 23 24 25 26 27 28 Fin Fin Hop_WR A_WR M1_WR VDD Bmode Smode, A3 M2_WR, A2 E_WR, A1 FSELP, A0 44-lead CQFJ Table 1. Pin Descriptions Pin No. (44-lead CQFJ) Pin Name Interface Mode Type Description 1 VDD ALL (Note 1) Power supply input. Input may range from 2.85 V to 3.15 V. Bypassing recommended. 2 R0 Direct Input R Counter bit0 (LSB). 3 R1 Direct Input R Counter bit1. 4 R2 Direct Input R Counter bit2. 5 R3 Direct Input R Counter bit3. 6 GND ALL (Note 1) Ground. D0 Parallel Input Parallel data bus bit0 (LSB). M0 Direct Input M Counter bit0 (LSB). D1 Parallel Input Parallel data bus bit1. M1 Direct Input M Counter bit1. D2 Parallel Input Parallel data bus bit2. M2 Direct Input M Counter bit2. D3 Parallel Input Parallel data bus bit3. M3 Direct Input M Counter bit3. 11 VDD ALL (Note 1) Same as pin 1. 12 VDD ALL (Note 1) Same as pin 1. S_WR Serial Input Serial load enable input. While S_WR is "low", Sdata can be serially clocked. Primary 7 8 9 10 13 Copyright Peregrine Semiconductor Corp. 2003 Page 2 of 14 File No. 70/0137~01A | UTSi CMOS RFIC SOLUTIONS PE83336 Product Specification Pin No. (44-lead CQFJ) Pin Name Interface Mode Type Description register data are transferred to the secondary register on S_WR or Hop_WR rising edge. D4 Parallel Input Parallel data bus bit4 M4 Direct Input M Counter bit4 Sdata Serial Input Binary serial data input. Input data entered MSB first. D5 Parallel Input Parallel data bus bit5. M5 Direct Input M Counter bit5. Sclk Serial Input Serial clock input. Sdata is clocked serially into the 20-bit primary register (E_WR "low") or the 8-bit enhancement register (E_WR "high") on the rising edge of Sclk. D6 Parallel Input Parallel data bus bit6. M6 Direct Input M Counter bit6. FSELS Serial Input Selects contents of primary register (FSELS=1) or secondary register (FSELS=0) for programming of internal counters while in Serial Interface Mode. D7 Parallel Input Parallel data bus bit7 (MSB). Pre_en Direct Input Prescaler enable, active "low". When "high", Fin bypasses the prescaler. GND ALL FSELP Parallel Input Selects contents of primary register (FSELP=1) or secondary register (FSELP=0) for programming of internal counters while in Parallel Interface Mode. A0 Direct Input A Counter bit0 (LSB). Serial Input Enhancement register write enable. While E_WR is "high", Sdata can be serially clocked into the enhancement register on the rising edge of Sclk. Parallel Input Enhancement register write. D[7:0] are latched into the enhancement register on the rising edge of E_WR. A1 Direct Input A Counter bit1. M2_WR Parallel Input M2 write. D[3:0] are latched into the primary register (R[5:4], M[8:7]) on the rising edge of M2_WR. A2 Direct Input A Counter bit2. Smode Serial, Parallel Input Selects serial bus interface mode (Bmode=0, Smode=1) or Parallel Interface Mode (Bmode=0, Smode=0). A3 Direct Input A Counter bit3 (MSB). 22 Bmode ALL Input Selects direct interface mode (Bmode=1). 23 VDD ALL (Note 1) Same as pin 1. 24 M1_WR Parallel Input M1 write. D[7:0] are latched into the primary register (Pre_en, M[6:0]) on the rising edge of M1_WR. 25 A_WR Parallel Input A write. D[7:0] are latched into the primary register (R[3:0], A[3:0]) on the rising edge of A_WR. 26 Hop_WR Serial, Parallel Input Hop write. The contents of the primary register are latched into the secondary register on the rising edge of Hop_WR. 27 Fin ALL Input Prescaler input from the VCO. 3.0 GHz max frequency. 28 Fin ALL Input Prescaler complementary input. A bypass capacitor should be placed as close as possible to this pin and be connected in series with a 50 resistor directly to the ground plane. 29 GND ALL 14 15 16 17 18 19 20 21 Ground. E_WR PEREGRINE SEMICONDUCTOR CORP. | Ground. http://www.peregrine-semi.com Copyright Peregrine Semiconductor Corp. 2003 Page 3 of 14 PE83336 Product Specification Pin No. (44-lead CQFJ) Pin Name Interface Mode Type Description 30 fp ALL Output Monitor pin for main divider output. Switching activity can be disabled through enhancement register programming or by floating or grounding VDD pin 31. 31 VDD-fp ALL (Note 1) VDD for fp. Can be left floating or connected to GND to disable the fp output. 32 Dout Serial, Parallel Output Data Out. The MSEL signal and the raw prescaler output are available on Dout through enhancement register programming. 33 VDD ALL (Note 1) Same as pin 1. 34 Cext ALL Output Logical "NAND" of PD_U and PD_D terminated through an on chip, 2 k series resistor. Connecting Cext to an external capacitor will low pass filter the input to the inverting amplifier used for driving LD. 35 VDD ALL (Note 1) Same as pin 1. 36 PD_D ALL Output PD_D is pulse down when fp leads fc. 37 PD_U ALL 38 VDD-fc ALL (Note 1) VDD for fc can be left floating or connected to GND to disable the fc output. 39 fc ALL Output Monitor pin for reference divider output. Switching activity can be disabled through enhancement register programming or by floating or grounding VDD pin 38. 40 GND ALL Ground. 41 GND ALL Ground. 42 fr ALL Input Reference frequency input. 43 LD ALL Output Lock detect and open drain logical inversion of CEXT. When the loop is in lock, LD is high impedance, otherwise LD is a logic low ("0"). 44 Enh Serial, Parallel Input Enhancement mode. When asserted low ("0"), enhancement register bits are functional. N/A NC ALL PD_U is pulse down when fc leads fp. No connection. Note 1: All VDD pins are connected by diodes and must be supplied with the same positive voltage level. VDD-fp and VDD-fp are used to power the fp and fc outputs and can alternatively be left floating or connected to GND to disable the fp and fc outputs. Note 2: All digital input pins have 70 k pull-down resistors to ground. Copyright Peregrine Semiconductor Corp. 2003 Page 4 of 14 File No. 70/0137~01A | UTSi CMOS RFIC SOLUTIONS PE83336 Product Specification Table 2. Absolute Maximum Ratings Symbol Electrostatic Discharge (ESD) Precautions Parameter/Conditions Min Max Units Supply voltage -0.3 4.0 V VI Voltage on any input -0.3 VDD + 0.3 V II DC into any input -10 +10 mA IO DC into any output -10 +10 mA Storage temperature range -65 150 C VDD Tstg Latch-Up Avoidance Unlike conventional CMOS devices, UTSi devices are immune to latch-up. Table 3. Operating Ratings Symbol (R) When handling this UTSi device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 4. Parameter/Conditions Min Max Units VDD Supply voltage 2.85 3.15 V TA Operating ambient temperature range -55 125 C (R) CMOS Table 4. ESD Ratings Symbol VESD Note 1: Parameter/Conditions ESD voltage (Human Body Model) Level Units 1000 V Periodically sampled, not 100% tested. Tested per MILSTD-883, M3015 C2 PEREGRINE SEMICONDUCTOR CORP. | http://www.peregrine-semi.com Copyright Peregrine Semiconductor Corp. 2003 Page 5 of 14 PE83336 Product Specification Table 5. DC Characteristics VDD = 3.0 V, -55 C TA 125 C, unless otherwise specified Symbol IDD Parameter Operational supply current; Prescaler disabled Prescaler enabled Conditions Min Typ Max Units 10 20 28 mA mA VDD = 2.85 to 3.15 V Digital Inputs: All except fr, R0, Fin, Fin VIH High level input voltage VDD = 2.85 to 3.15 V VIL Low level input voltage VDD = 2.85 to 3.15 V IIH High level input current VIH = VDD = 3.15 V IIL Low level input current VIL = 0, VDD = 3.15 V 0.7 x VDD V 0.3 x VDD V +70 A A -1 Reference Divider input: fr IIHR High level input current VIH = VDD = 3.15 V IILR Low level input current VIL = 0, VDD = 3.15 V +100 A A -100 R0 Input (Pull-up Resistor): R0 IIHRO High level input current VIH = VDD = 3.15 V IILRO Low level input current VIL = 0, VDD = 3.15 V +70 A A -5 Counter and phase detector outputs: fc, fp, PD_D, PD_U VOLD Output voltage LOW Iout = 6mA VOHD Output voltage HIGH Iout = -3mA 0.4 VDD - 0.4 V V Lock detect outputs: Cext, LD VOLC Output voltage LOW, Cext Iout = 100uA VOHC Output voltage HIGH, Cext Iout = -100uA VOLLD Output voltage LOW, LD Iout = 6mA Copyright Peregrine Semiconductor Corp. 2003 Page 6 of 14 0.4 VDD - 0.4 V 0.4 File No. 70/0137~01A V | UTSi V CMOS RFIC SOLUTIONS PE83336 Product Specification Table 6. AC Characteristics VDD = 3.0 V, -55 C TA 125 C, unless otherwise specified Symbol Parameter Conditions Min Typ Max Units 10 MHz Control Interface and Latches (see Figures 3, 4, 5) fClk Serial data clock frequency tClkH Serial clock HIGH time 30 ns tClkL Serial clock LOW time 30 ns tDSU Sdata set-up time after Sclk rising edge, D[7:0] set-up time to M1_WR, M2_WR, A_WR, E_WR rising edge 10 ns tDHLD Sdata hold time after Sclk rising edge, D[7:0] hold time to M1_WR, M2_WR, A_WR, E_WR rising edge 10 ns tPW S_WR, M1_WR, M2_WR, A_WR, E_WR pulse width 30 ns tCWR Sclk rising edge to S_WR rising edge. S_WR, M1_WR, M2_WR, A_WR falling edge to Hop_WR rising edge 30 ns Sclk falling edge to E_WR transition 30 ns S_WR falling edge to Sclk rising edge. Hop_WR falling edge to S_WR, M1_WR, M2_WR, A_WR rising edge 30 ns tEC E_WR transition to Sclk rising edge 30 ns tMDO MSEL data out delay after Fin rising edge tCE tWRC CL = 12 pf 8 (Note 5) ns Main Divider (Including Prescaler) Fin Operating frequency PFin Input level range 500 3000 MHz External AC coupling -5 5 dBm External AC coupling 0 5 dBm 85C < TA 125C Main Divider (Prescaler Bypassed) Fin Operating frequency PFin Input level range 50 300 MHz External AC coupling -5 5 dBm External AC coupling 0 5 dBm 85C < TA 125C Reference Divider fr Operating frequency (Note 1) (Note 2) 100 MHz Pfr Reference input power Single ended input -2 10 dBm Vfr Input sensitivity External AC coupling (Note 3) 0.5 VP-P Phase Detector fc Comparison frequency (Note 1) 20 MHz SSB Phase Noise : Output Referred (Fin = 1918MHz, fr = 10 MHz, fc = 1MHz, LBW = 70 kHz) PNOR Output Referred Phase Noise 100 Hz Offset: VDD = 3.0V, T = 25C -78 (Note 4) dBc/Hz PNOR Output Referred Phase Noise 1000 Hz Offset: VDD = 3.0V, T = 25C -94 (Note 4) dBc/Hz Note 1: Parameter is guaranteed through characterization only and is not tested. Note 2: Running at low frequencies (< 10 MHz sinewave), the device will still be functional but may cause phase noise degradation. Inserting a lownoise amplifier to square up the edges is recommended at lower input frequencies. Note 3: CMOS logic levels may be used if DC coupled. For optimum phase noise performance, the reference input falling edge rate should be faster than 80mV/ns. Note 4: All devices are screened to phase noise limits listed in Table 7. The magnitude of the tester uncertainty precludes testing phase noise as part of qualification testing. These parameters are also exempt from PDA requirements. Note 5: Parameter is tested using 100pF load capacitance and is guaranteed through characterization only. Typical test delay is 12nS. PEREGRINE SEMICONDUCTOR CORP. | http://www.peregrine-semi.com Copyright Peregrine Semiconductor Corp. 2003 Page 7 of 14 PE83336 Product Specification Table 7. Phase Noise Test Test name Conditions Max Units Phase Noise 100 Hz Offset -80 dBc/Hz 1000 Hz Offset -87 dBc/Hz Functional Description The PE83336 consists of a prescaler, counters, a phase detector and control logic. The dual modulus prescaler divides the VCO frequency by either 10 or 11, depending on the value of the modulus select. Counters "R" and "M" divide the reference and prescaler output, respectively, by integer values stored in a 20-bit register. An additional counter ("A") is used in the modulus select logic. The phasefrequency detector generates up and down frequency control signals. The control logic includes a selectable chip interface. Data can be written via serial bus, parallel bus, or hardwired direct to the pins. There are also various operational and test modes and lock detect. Figure 3. Functional Block Diagram R Counter (6-bit) fr D(7:0) Sdata R(5:0) Control Logic PD_U Phase Detector M(8:0) Control Pins fc PD_D A(3:0) LD Cext 2k Modulus Select Fin Fin 10/11 Prescaler Copyright Peregrine Semiconductor Corp. 2003 Page 8 of 14 M Counter (9-bit) fp File No. 70/0137~01A | UTSi CMOS RFIC SOLUTIONS PE83336 Product Specification Main Counter Chain Register Programming The main counter chain divides the RF input frequency, Fin, by an integer derived from the user defined values in the "M" and "A" counters. It is composed of the 10/11 dual modulus prescaler, modulus select logic, and 9-bit M counter. Setting Pre_en "low" enables the 10/11 prescaler. Setting Pre_en "high" allows Fin to bypass the prescaler and powers down the prescaler. Parallel Interface Mode The output from the main counter chain, fp, is related to the VCO frequency, Fin, by the following equation: fp = Fin / [10 x (M + 1) + A] where A M + 1, 1 M 511 (1) When the loop is locked, Fin is related to the reference frequency, fr, by the following equation: Fin = [10 x (M + 1) + A] x (fr / (R+1)) where A M + 1, 1 M 511 (2) A consequence of the upper limit on A is that Fin must be greater than or equal to 90 x (fr / (R+1)) to obtain contiguous channels. Programming the M Counter with the minimum value of "1" will result in a minimum M Counter divide ratio of "2". When the prescaler is bypassed, the equation becomes: Fin = (M + 1) x (fr / (R+1)) where 1 M 511 (3) In Direct Interface Mode, main counter inputs M7 and M8 are internally forced low. Reference Counter The reference counter chain divides the reference frequency, fr, down to the phase detector comparison frequency, fc. The output frequency of the 6-bit R Counter is related to the reference frequency by the following equation: fc = fr / (R + 1) where 0 R 63 (4) Note that programming R equal to "0" will pass the reference frequency, fr, directly to the phase detector. In Direct Interface Mode, R Counter inputs R4 and R5 are internally forced low ("0"). PEREGRINE SEMICONDUCTOR CORP. | http://www.peregrine-semi.com Parallel Interface Mode is selected by setting the Bmode input "low" and the Smode input "low". Parallel input data, D[7:0], are latched in a parallel fashion into one of three, 8-bit primary register sections on the rising edge of M1_WR, M2_WR, or A_WR per the mapping shown in Table 7 on page 10. The contents of the primary register are transferred into a secondary register on the rising edge of Hop_WR according to the timing diagram shown in Figure 4. Data are transferred to the counters as shown in Table 7 on page 10. The secondary register acts as a buffer to allow rapid changes to the VCO frequency. This double buffering for "ping-pong" counter control is programmed via the FSELP input. When FSELP is "high", the primary register contents set the counter inputs. When FSELP is "low", the secondary register contents are utilized. Parallel input data, D[7:0], are latched into the enhancement register on the rising edge of E_WR according to the timing diagram shown in Figure 4. This data provides control bits as shown in Table 8 on page 10 with bit functionality enabled by asserting the Enh input "low". Serial Interface Mode Serial Interface Mode is selected by setting the Bmode input "low" and the Smode input "high". While the E_WR input is "low" and the S_WR input is "low", serial input data (Sdata input), B0 to B19, are clocked serially into the primary register on the rising edge of Sclk, MSB (B0) first. The contents from the primary register are transferred into the secondary register on the rising edge of either S_WR or Hop_WR according to the timing diagram shown in Figures 4-5. Data are transferred to the counters as shown in Table 7 on page 10. The double buffering provided by the primary and secondary registers allows for "ping-pong" counter control using the FSELS input. When FSELS is "high", the primary register contents set the counter inputs. When FSELS is "low", the secondary register contents are utilized. While the E_WR input is "high" and the S_WR input is "low", serial input data (Sdata input), B0 to B7, are clocked serially into the enhancement register on the rising edge of Sclk, MSB (B0) first. The enhancement register is double buffered to prevent Copyright Peregrine Semiconductor Corp. 2003 Page 9 of 14 PE83336 Product Specification inadvertent control changes during serial loading, with buffer capture of the serially entered data performed on the falling edge of E_WR according to the timing diagram shown in Figure 5. After the falling edge of E_WR, the data provide control bits as shown in Table 8 with bit functionality enabled by asserting the Enh input "low". Direct Interface Mode Direct Interface Mode is selected by setting the Bmode input "high". Counter control bits are set directly at the pins as shown in Table 7. In Direct Interface Mode, main counter inputs M7 and M8, and R Counter inputs R4 and R5 are internally forced low ("0"). Table 8. Primary Register Programming Interface Mode Enh Bmode Smode Parallel 1 0 0 R5 R4 M8 M7 Pre_en M6 M2_WR rising edge load M5 M4 M3 M2 M1 M0 R3 R2 M1_WR rising edge load R1 R0 A3 A2 A1 A0 A_WR rising edge load D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Serial* 1 0 1 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 Direct 1 1 X 0 0 0 0 Pre_en M6 M5 M4 M3 M2 M1 M0 R3 R2 R1 R0 A3 A2 A1 A0 *Serial data clocked serially on Sclk rising edge while E_WR "low" and captured in secondary register on S_WR rising edge. MSB (first in) (last in) LSB Table 9. Enhancement Register Programming Interface Mode Enh Bmode Smode Parallel 0 X 0 Serial* 0 X 1 Power down Reserved Reserved Reserved D7 D6 D5 D4 B0 B1 B2 B3 Counter load MSEL output Prescaler output fc, fp OE D3 D2 D1 D0 B4 B5 B6 B7 E_WR rising edge load *Serial data clocked serially on Sclk rising edge while E_WR "high" and captured in the double buffer on E_WR falling edge. MSB (first in) Copyright Peregrine Semiconductor Corp. 2003 Page 10 of 14 (last in) LSB File No. 70/0137~01A | UTSi CMOS RFIC SOLUTIONS PE83336 Product Specification Figure 4. Parallel Interface Mode Timing Diagram tDSU tDHLD D [7 : 0] tPW tCWR tWRC M1_WR M2_WR A_WR tPW E_WR Hop_WR Figure 5. Serial Interface Mode Timing Diagram Sdata E_WR tEC tCE Sclk S_WR tDSU PEREGRINE SEMICONDUCTOR CORP. | tDHLD http://www.peregrine-semi.com tClkH tClkL tCWR tPW tWRC Copyright Peregrine Semiconductor Corp. 2003 Page 11 of 14 PE83336 Product Specification Enhancement Register The functions of the enhancement register bits are shown below with all bits active "high". Table 10. Enhancement Register Bit Functionality Bit Function Bit 0 Reserved** Bit 1 Reserved** Description Bit 2 Reserved** Bit 3 Power down Power down of all functions except programming interface. Bit 4 Counter load Immediate and continuous load of counter programming as directed by the Bmode and Smode inputs. Bit 5 MSEL output Bit 6 Prescaler output Bit 7 fp, fc OE Drives the internal dual modulus prescaler modulus select (MSEL) onto the Dout output. Drives the raw internal prescaler output onto the Dout output. fp, fc outputs disabled. ** Program to 0 Phase Detector The phase detector is triggered by rising edges from the main Counter (fp) and the reference counter (fc). It has two outputs, PD_U, and PD_D. If the divided VCO leads the divided reference in phase or frequency (fp leads fc), PD_D pulses "low". If the divided reference leads the divided VCO in phase or frequency (fc leads fp), PD_U pulses "low". The width of either pulse is directly proportional to phase offset between the two input signals, fp and fc . The phase detector gain is equal to 2.7 V / 2 , which numerically yields 0.43 V / radian. Copyright Peregrine Semiconductor Corp. 2003 Page 12 of 14 PD_U and PD_D drive an active loop filter which controls the VCO tune voltage. PD_U pulses result in an increase in VCO frequency; PD_D pulses result in a decrease in VCO frequency (for a positive Kv VCO). A lock detect output, LD is also provided, via the pin Cext. Cext is the logical "NAND" of PD_U and PD_D waveforms, which is driven through a series 2 kohm resistor. Connecting Cext to an external shunt capacitor provides low pass filtering of this signal. Cext also drives the input of an internal inverting comparator with an open drain output. Thus LD is an "AND" function of PD_U and PD_D. File No. 70/0137~01A | UTSi CMOS RFIC SOLUTIONS PE83336 Product Specification Figure 6. Package Drawing 44-lead CQFJ All dimensions are in mils Table 11. Ordering Information Order Code Part Marking 83336-21 PE83336 83336-22 83336-00 Description Package Shipping Method Packaged Part 44-lead CQFJ 26 units / Tube PE83336 Packaged Part 44-lead CQFJ 500 units / T&R PE83336EK CQFJ Evaluation Board with Software 44-lead CQFJ 1 / Box PEREGRINE SEMICONDUCTOR CORP. | http://www.peregrine-semi.com Product Status Copyright Peregrine Semiconductor Corp. 2003 Page 13 of 14 PE83336 Product Specification Sales Offices United States Japan Peregrine Semiconductor Corp. Peregrine Semiconductor K.K. 6175 Nancy Ridge Drive San Diego, CA 92121 Tel 1-858-455-0660 Fax 1-858-455-0770 5A-5, 5F Imperial Tower 1-1-1 Uchisaiwaicho, Chiyoda-ku, Tokyo, Japan 100-011 Tel. 011-81-3-3502-5211 Fax. 011-81-3-3502-5213 Europe Peregrine Semiconductor Europe Aix-En-Provence Office Parc Club du Golf, bat 9 13856 Aix-En-Provence Cedex 3 France Tel 011-33-0-4-4239-3360 Fax 011-33-0-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: http://www.peregrine-semi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a PCN (Product Change Notice). The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. Peregrine products are protected under one or more of the following U.S. patents: 6,090,648; 6,057,555; 5,973,382; 5,973,363; 5,930,638; 5,920,233; 5,895,957; 5,883,396; 5,864,162; 5,863,823; 5,861,336; 5,663,570; 5,610,790; 5,600,169; 5,596,205; 5,572,040; 5,492,857; 5,416,043. Other patents are pending. Peregrine, the Peregrine logotype, Peregrine Semiconductor Corp., and UTSi are registered trademarks of Peregrine Semiconductor Corporation. Copyright (c) 2003 Peregrine Semiconductor Corp. All rights reserved. Copyright Peregrine Semiconductor Corp. 2003 Page 14 of 14 File No. 70/0137~01A | UTSi CMOS RFIC SOLUTIONS