HCM1206A Page 1 of 5 BeStar Technologies Inc. Address: 761 N. 17th Street Unit 4, St. Charles, IL 60174 Tel : 847-261-2850 E-mail : sales@bestartech.com Web : www.bestartech.com Document Number Revision Total Pages Prepare by Date : 9611-15 : A6 :5 : Holmes, Poon : 6 January, 2012 SoniCrest Brand Acoustic Components www.jlsonicrest.com Document Type : Specification Product Type : Electro-magnetic Sound Generator Component Part Number : HCM1206A A3 - Updated layout & format by WH Chan on 13 Feb., 2001 A4 - Updated RoHS version by Leo, Sin on 11 Aug., 2005 A5 - Updated format by Holmes, Poon on 24 Sept., 2010 A6 - Added section 7 by Holmes, Poon on 6 Jan., 2012 This material is the property of BeStar Technologies Inc. Unauthorized copying or use of this material is prohibited. Rev. A6 HCM1206A 1. Page 2 of 5 Purpose and Scope This document contains both general requirements, qualification requirements, and those specific electrical, mechanical requirements for this part. 2. Description O12mm electro-magnetic sound generator, RoHS compliant. 3. Application Telecommunication Equipment, Computers and Peripherals, Portable Equipment, Automobile Electronics, POS System, etc. 4. Component Requirement 4.1. 4.2. General Requirement 4.1.1. Operating Temperature Range : -40C to +85C 4.1.2. Storage Temperature Range : -40C to +85C 4.1.3. Weight : 2g 4.1.4. Housing Material : Noryl SE1-GFM2 Electrical Requirement 4.2.1. Rated Voltage : 6V 4.2.2. Operating Voltage :4~8V 4.2.3. Rated Current : <=60mA 4.2.4. Coil Resistance : 45 5 W 4.2.5. Rated Frequency : 2400Hz 4.2.6. Sound Pressure Level at 10cm (Applying rated voltage) : >=85dB dB 90 80 70 60 1K 500 2K 3K 4K 5K 10K Figure 1. Frequency Response 4.3. Mechanical Requirement 4.3.1. Layout and Dimension : See Section 6, Figure 3 Rev. A6 HCM1206A 4.4. Page 3 of 5 Test Setup 10cm Type 1 Calibrated SPL Meter Test Specimen - Transistor (Vce <= 0.15V hFE >= 200) 200 ohm + + Diode Testing Voltage from D.C. Power Supply (Input Voltage) 2.5V 0V 2.5V0-p, 1/2 Duty Square Wave from Signal Generator (50 ohm impedance) (Input frequency) _ Figure 2. Test Setup Notes : Apply 2.5V0-p from Signal Generator, set 2400Hz from Signal Generator. Measure SPL using a calibrated SPL meter 10cm from the sound port. Sound level meter to be in accordance with IEC651 (1979) Type 1 and/or ANSI S1.4-1983. The meter must be checked on a daily basis using a calibrated acoustic calibrator recommended by the manufacturer. Measurement should be carried out in a free field environment or at least 40cm from any surface. Rev. A6 HCM1206A 5.1. Operating Life : Subject samples to room condition for 96 hours under rated voltage 5.2. High Temperature : Subject samples to +85 3 C and operate for 96 hours. Components must be fully stabilized at temperature extremes before data is taken, which may require up to a 2 hours soak. 5.3. Low Temperature : Subject samples to -40 3 C and operate for 96 hours. Components must be fully stabilized at temperature extremes before data is taken, which may require up to a 2 hours soak. 5.4. Temperature Shock : Each temperature cycle shall consist of 30 minutes at -30C, 15 minutes at +20C, 30 minutes at +80C and 15 minutes at +20C. Test duration is for 5 cycles. Components must be fully stabilized at temperature extremes before data is taken, which may require up to a 2 hours soak. 5.5. Static Humidity : Precondition at room temperature for 1 hour. Then expose to +40C with 90% to 95% relative humidity for 96 hours. Finally dry at room ambient for 2 hours before taking final measurement. 5.6. Drop Test : Drop samples naturally from the height of 1.5m onto a 10mm thickness wooden board in 3 directions (x, y and z). Mechanical Layout XX.X XX.XX Angular (unless otherwise specified) Top View = 0.3 = 0.05 = 0.25 Bottom View Side View 7 6.5 0.5 O12 sealing label O0.6 Unit : mm Tolerance : Linear JL 6. Reliability Test HCM1 5. Page 4 of 5 O2 .2 9 5.5 Figure 3. HCM1206A Mechanical Layout Rev. A6 HCM1206A Standard Packing Requirements Packing Quantity : 100 pieces per tray 10 trays per unit, 5 units per carton (Total 5000 pieces) 7.2. Canton Layout 5 280 7.1. 50 7. Page 5 of 5 420 Figure 4. Tray and Carton Layout Rev. A6