SIMATIC Sensors RFID systems RF300 MDS D422 Compact Operating Instructions Characteristics MDS D422 Characteristics Field of application Identification of metallic workpiece holders, workpieces or containers Memory FRAM 2048 bytes gross 2000 bytes net Read/write range See Chapter Field data (Page 2). ISO standard Oriented according to ISO standard 15693 Ordering data Table 1 Ordering data of MDS D422 Order number MDS D422 6GT2600-4AF00 A screw-in aid is included in the scope of supply per packaging unit Safety instructions for the device/system NOTICE This device/system may only be used for the application instances that have been described in the catalog and the technical documentation "System Manual SIMATIC RF300 (http://support.automation.siemens.com/WW/view/de/21738946/0/en)" and only in combination with third-party devices and components recommended and/or approved by Siemens. (c) Siemens 2010 J31069-D0233-U001-A1-7618, 09/2010 1 Technical specifications Mounting on metal Flush-mounting Table 3 Technical data of MDS D426 Memory size 2048 bytes Memory configuration Serial number 8 bytes (fixed code) Configuration memory 40 bytes Application memory 2000 bytes Storage technology FRAM Memory organization FRAM 2048 bytes / gross 2000 bytes net When using the OPT area, 16 bytes of it must be subtracted in 8 byte blocks Figure 1 Protocol Mounting of MDS D422 in metal Mounting information for screws You can screw the transponder into a pre-drilled threaded hole using the screw-in aid. Mounting information for adhesion Drill installation hole The adhesive surfaces must be dry, free from dust, oil, stripping agents and other impurities Apply adhesive according to the manufacturer's processing instructions Press in MDS D422 using your fingers; with antenna side to the outside (see Fig.) Remove residues of adhesive Allow to cure according to the manufacturer's instructions Flush-mounting of MDS D422 in metal with tools Field data Table 2 Field data MDS D422 - RF300 reader ISO 15693 Data retention (at +40 C) 10 years MTBF (at + 40C) 2 x 106 h Data transmission rate approx. 2 ms/byte Reading and writing Bulk detection/multitag capability Yes Read cycles Unlimited Write cycles >1010 (at + 40 C, typical) Read/write distance (Sg) See Chapter Field data (Page 2) Distance from metal 25 mm (approx. 25 % reduction of the field data) Power supply Inductive power transmission (without battery) Degree of protection to EN 60529 IP68 1) Shock, tested in accordance with IEC 68-2-27 50 g 2) Vibration, tested in accordance with IEC 68-2-6 20 g 2) Torsion and bending load Not permissible Enclosure RF350R ANT 18 RF350R ANT 30 Color Black Material Plastic PA 6.6 GF 0 ... 10 0 ... 12 Dimensions (thread, H) M20 x 1 mm, 6 0.2 mm 13 15 Transmission window (Lx/Ly) 15 25 Minimum distance from MDS to MDS 100 100 Operating distance (Sa) Limit distance (Sg) All values are in mm MDS fixing Screw in (M20 x 1 mm) Adhere Ambient temperature During operation -25 C to +85 C Transport and storage -40 C to +100 C Weight, approx. 13 g 1) 2 hours, 2 m, +20 C 2) The values for shock and vibration are maximum values and must not be applied continuously. Note It is recommended that a test is performed in critical applications. 2 MDS D422 J31069-D0233-U001-A1-7618, 09/2010 Dimension drawing 0 [ Service & support s Dimensions in mm Figure 2 Dimensional drawing of MDS D422 Technical support Phone: + 49 (0) 911 895 7222 Fax: + 49 (0) 911 895 7223 E-mail (mailto:support.automation@siemens.com) Internet: Online support request form: (www.siemens.com/automation/support-request) Service & support at IA/DT Support homepage (www.siemens.com/automation/service&support) RFID homepage For general information about our identification systems, visit RFID homepage (www.siemens.com/simaticsensors/rf). Siemens AG Industry Sector Postfach 48 48 90026 NURNBERG MDS D422 J31069-D0233-U001-A1-7618, 09/2010 3