IRLI2910PbF Logic -Level Gate Drive Advanced Process Technology Ultra Low On-Resistance Isolated Package High Voltage Isolation = 2.5KVRMS Sink to Lead Creepage Dist. = 4.8mm Fully Avalanche Rated Lead-Free HEXFET(R) Power MOSFET Description Fifth Generation HEXFETs from International Rectifier utilize advanced processing techniques to achieve extremely low onresistance per silicon area. This benefit, combined with the fast switching speed and ruggedized device design that HEXFET Power MOSFETs are well known for, provides the designer with an extremely efficient and reliable device for use in a wide variety of applications. The TO-220 Full Pak eliminates the need for additional insulating hardware in commercial-industrial applications. The molding compound used provides a high isolation capability and a low thermal resistance between the tab and external heat sink. This isolation is equivalent to using a 100 micron mica barrier with standard TO-220 product. The Fullpak is mounted to a heat sink using a single clip or by a single screw fixing. Base Part Number Package Type IRLI2910PbF TO-220 Full-Pak Absolute Maximum Ratings Symbol VDSS 100V RDS(on) 0.026 ID 31A G G Gate D Drain Standard Pack Form Quantity Tube 50 IRLI2910PbF Parameter Max. Continuous Drain Current, VGS @ 10V 31 Continuous Drain Current, VGS @ 10V Pulsed Drain Current Maximum Power Dissipation 22 190 63 Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy (Thermally Limited) Avalanche Current Repetitive Avalanche Energy Peak Diode Recovery dv/dt Operating Junction and Storage Temperature Range Soldering Temperature, for 10 seconds (1.6mm from case) Mounting torque, 6-32 or M3 screw 0.42 16 1 Parameter S Source Orderable Part Number ID @ TC = 25C Thermal Resistance Symbol Junction-to-Case RJC Junction-to-Ambient RJA S TO-220 Full-Pak ID @ TC = 100C IDM PD @TC = 25C VGS EAS IAR EAR dv/dt TJ TSTG D Units A W 520 29 6.3 5.0 -55 to + 175 W/C V mJ A mJ V/ns C 300 10 lbf*in (1.1N*m) Typ. --- --- Max. 2.4 65 Units C/W 2017-08-22 IRLI2910PbF Electrical Characteristics @ TJ = 25C (unless otherwise specified) V(BR)DSS V(BR)DSS/TJ Parameter Drain-to-Source Breakdown Voltage Breakdown Voltage Temp. Coefficient Qg Qgs Qgd td(on) tr td(off) tf Gate-to-Source Forward Leakage Gate-to-Source Reverse Leakage Total Gate Charge Gate-to-Source Charge Gate-to-Drain Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Min. 100 --- --- --- --- 1.0 28 --- --- --- --- --- --- --- --- --- --- --- RDS(on) Static Drain-to-Source On-Resistance VGS(th) gfs Gate Threshold Voltage Forward Trans conductance IDSS Drain-to-Source Leakage Current LD Internal Drain Inductance --- LS Internal Source Inductance --- IGSS Ciss Input Capacitance Coss Output Capacitance Crss Reverse Transfer Capacitance C Drain to Sink Capacitance Source-Drain Ratings and Characteristics Parameter Continuous Source Current IS (Body Diode) Pulsed Source Current ISM (Body Diode) VSD Diode Forward Voltage --- --- --- --- Typ. Max. Units Conditions --- --- V VGS = 0V, ID = 250A 0.12 --- V/C Reference to 25C, ID = 1mA --- 0.026 VGS = 10V, ID = 16A --- 0.030 VGS = 5.0V, ID = 16A --- 0.040 VGS = 4.0V, ID = 14A --- 2.0 V VDS = VGS, ID = 250A --- --- S VDS = 50V, ID = 29A --- 25 VDS = 100V, VGS = 0V A --- 250 VDS = 80V,VGS = 0V,TJ =150C --- 100 VGS = 16V nA --- -100 VGS = -16V --- 140 ID = 29A nC VDS = 80V --- 20 VGS = 5.0V , See Fig. 6 and 13 --- 81 11 --- VDD = 50V 100 --- ID = 29A ns 49 --- RG= 1.4VGS = 5.0V 55 --- RD= 1.7See Fig. 10 Between lead, 4.5 --- 6mm (0.25in.) nH from package 7.5 --- and center of die contact 3700 --- VGS = 0V 630 --- VDS = 25V pF = 1.0MHz, See Fig. 5 330 --- 12 --- = 1.0MHz Min. Typ. --- --- 31 --- --- 190 --- --- 1.3 V Conditions MOSFET symbol showing the integral reverse p-n junction diode. TJ = 25C,IS = 16A,VGS = 0V Max. Units A trr Reverse Recovery Time --- 240 350 ns TJ = 25C ,IF = 29A Qrr Reverse Recovery Charge --- 1.8 2.7 C di/dt = 100A/s Notes: Repetitive rating; pulse width limited by max. junction temperature. (See fig. 11) VDD = 25V, starting TJ = 25C, L = 1.2mH, RG = 25, IAS = 29A (See fig. 12) ISD 29A, di/dt 490A/s, VDD V(BR)DSS, TJ 175C. Pulse width 300s; duty cycle 2%. t=60s, =60Hz Uses IRL2910 data and test conditions. 2 2017-08-22 IRLI2910PbF Fig. 1 Typical Output Characteristics Fig. 3 Typical Transfer Characteristics 3 Fig. 2 Typical Output Characteristics Fig. 4 Normalized On-Resistance vs. Temperature 2017-08-22 IRLI2910PbF Fig 5. Typical Capacitance vs. Drain-to-Source Voltage Fig. 7 Typical Source-to-Drain Diode Forward Voltage 4 Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage Fig 8. Maximum Safe Operating Area 2017-08-22 IRLI2910PbF Fig 10a. Switching Time Test Circuit Fig 9. Maximum Drain Current vs. Case Temperature Fig 10b. Switching Time Waveforms Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case 5 2017-08-22 IRLI2910PbF 15V L VDS DRIVER D.U.T RG + V - DD IAS 20V tp A 0.01 Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp Fig 12c. Maximum Avalanche Energy vs. Drain Current I AS Fig 12b. Unclamped Inductive Waveforms Fig 13a. Gate Charge Waveform 6 Fig 13b. Gate Charge Test Circuit 2017-08-22 IRLI2910PbF Fig 14. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET(R) Power MOSFETs 7 2017-08-22 IRLI2910PbF TO-220 Full-Pak Package Outline (Dimensions are shown in millimeters (inches)) TO-220 Full-Pak Part Marking Information TO-220AB Full-Pak packages are not recommended for Surface Mount Application. Note: For the most current drawing please refer to website at http://www.irf.com/package/ 8 2017-08-22 IRLI2910PbF Qualification Information Industrial (per JEDEC JESD47F) Qualification Level TO-220 Full-Pak Moisture Sensitivity Level N/A Yes RoHS Compliant Applicable version of JEDEC standard at the time of product release. Revision History Date Comments 04/27/2017 Changed datasheet with Infineon logo - all pages. Corrected Package Outline on page 8. Added disclaimer on last page. 08/22/17 Updated typo for Vgsth max value from 4.0V to 2.0V-page2 Trademarks of Infineon Technologies AG HVICTM, IPMTM, PFCTM, AU-ConvertIRTM, AURIXTM, C166TM, CanPAKTM, CIPOSTM, CIPURSETM, CoolDPTM, CoolGaNTM, COOLiRTM, CoolMOSTM, CoolSETTM, CoolSiCTM, DAVETM, DI-POLTM, DirectFETTM, DrBladeTM, EasyPIMTM, EconoBRIDGETM, EconoDUALTM, EconoPACKTM, EconoPIMTM, EiceDRIVERTM, eupecTM, FCOSTM, GaNpowIRTM, HEXFETTM, HITFETTM, HybridPACKTM, iMOTIONTM, IRAMTM, ISOFACETM, IsoPACKTM, LEDrivIRTM, LITIXTM, MIPAQTM, ModSTACKTM, my-dTM, NovalithICTM, OPTIGATM, OptiMOSTM, ORIGATM, PowIRaudioTM, PowIRStageTM, PrimePACKTM, PrimeSTACKTM, PROFETTM, PRO-SILTM, RASICTM, REAL3TM, SmartLEWISTM, SOLID FLASHTM, SPOCTM, StrongIRFETTM, SupIRBuckTM, TEMPFETTM, TRENCHSTOPTM, TriCoreTM, UHVICTM, XHPTM, XMCTM Trademarks updated November 2015 Other Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2016-04-19 Published by Infineon Technologies AG 81726 Munich, Germany (c) 2016 Infineon Technologies AG. All Rights Reserved. Do you have a question about this document? Email: erratum@infineon.com Document reference ifx1 IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie") . With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. 9 For further information on the product, technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies office (www.infineon.com). Please note that this product is not qualified according to the AEC Q100 or AEC Q101 documents of the Automotive Electronics Council. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies' products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury. 2017-08-22