DATA SHEET LEAD FREE CHIP RESISTORS RC_P series 0.5%, 1%, 5% Product specification - June 07, 2017 V.0 Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512 Product specification Chip Resistor Surface Mount SCOPE This specification describes RC series chip resistors with made by thick film process. APPLICATIONS All general purpose application RC_P SERIES 2 8 0100 to 2512 ORDERING INFORMATION - GLOBAL PART NUMBER Global part numbers are identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. GLOBAL PART NUMBER RC XXXX X X X XX XXXX P (1) (2) (3) (4) (5) (6) (7) (1) SIZE 0100/0201/0402/0603/0805/1206/1210/1218/2010/2512 FEATURES Total lead free without RoHS exemption Halogen Free Epoxy Reducing environmentally hazardous wastes High component and equipment reliability Saving of PCB space (2) TOLERANCE D = 0.5% F = 1.0% J = 5.0% ( for jumper ordering, use code of J) (3) PACKAGING TYPE R = Paper taping reel K = Embossed taping reel S = ESD safe reel (0100 only) (4) TEMPERATURE COEFFICIENT OF RESISTANCE = Based on spec. (5) TAPING REEL 07 = 7 inch dia. Reel 13 =13 inch dia. Reel 7N = 7 inch dia. Reel, ESD safe reel (0100 only) (6) RESISTANCE VALUE There are 2~4 digits indicated the resistance value. Letter R/K/M is decimal point. Example: 97R6 = 97.6 9K76 = 9760 1M = 1,000,000 (7) DEFAULT CODE Letter P is lead free (without RoHS exemption) ORDERING EXAMPLE The ordering code for a RC0402 0.0625W chip resistor value 100K with 5% tolerance, supplied in 7-inch tape reel of 10,000 units per reel is: RC0402JR-07100KP. www.yageo.com Jun. 07, 2017 V.0 Product specification Chip Resistor Surface Mount RC_P SERIES 3 8 0100 to 2512 MARKING RC0100 / RC0201 / RC0402 No Marking Fig. 1 RC0603 03 Fig. 2 E24 series: 3 digits, 5% First two digits for significant figure and 3rd digit for number of zeros Value = 10 K RC0805 / RC1206 / RC1210 / RC1218 / RC2010 / RC2512 00 Fig. 3 Value = 10 K E24/E96 series: 4 digits, 1%, 0.5% First three digits for significant figure and 4th digit for number of zeros Note For further marking information, please see special data sheet "Chip resistors marking". CONSTRUCTION The resistor is constructed on top of a high-grade ceramic body. Internal metal electrodes are added on each end to make the contacts to the thick film resistive element. The composition of the resistive element is a noble metal imbedded into a glass and covered by a second glass to prevent environmental influences. The resistor is laser trimmed to the rated resistance value. The resistor is covered with a protective epoxy coat, finally the two external terminations (matte tin on Nibarrier) are added, as shown in Fig.4. Outlines For dimensions, please refer to Table 1 Fig. 4 Chip resistor outlines www.yageo.com Jun. 07, 2017 V.0 Product specification Chip Resistor Surface Mount SERIES RC_P 4 8 0100 to 2512 DIMENSION Table 1 TYPE L (mm) W (mm) H (mm) I1 (mm) I2 (mm) RC0100 0.400.02 0.200.02 0.130.02 0.100.03 0.100.03 RC0201 0.600.03 0.300.03 0.230.03 0.100.05 0.150.05 RC0402 1.000.05 0.500.05 0.350.05 0.200.10 0.250.10 RC0603 1.600.10 0.800.10 0.450.10 0.250.15 0.250.15 RC0805 2.000.10 1.250.10 0.500.10 0.350.20 0.350.20 RC1206 3.100.10 1.600.10 0.550.10 0.450.20 0.400.20 RC1210 3.100.10 2.600.15 0.550.10 0.450.15 0.500.20 RC1218 3.100.10 4.600.10 0.550.10 0.450.20 0.400.20 RC2010 5.000.10 2.500.15 0.550.10 0.450.15 0.500.20 RC2512 6.350.10 3.100.15 0.550.10 0.600.20 0.500.20 ELECTRICAL CHARACTERISTICS Table 2 CHARACTERISTICS RESISTANCE RANGE TYPE Fig. 4 Operating Max. Temperature Working Range Voltage Chip resistor outlines RC0100 Max. Dielectric Overload Withstandin Voltage g Voltage 15V 30V 30V 1R10: -200~+600ppm/ 10<R100: 370ppm/ 100<R1M: 250ppm/ 25V 50V 50V 1R10: -100~+500ppm/ 10<R100: 300ppm/ 100<R10M: 200ppm/ 100 V 100 V 1R10: 350ppm/ 10<R100: 200ppm/ 100<R10M: 150ppm/ 10M<R22M: 200ppm/ 150 V 1R10: 300ppm/ 10<R100: 200ppm/ 150 V 100<R10M: 150ppm/ 10M<R22M: 200ppm/ 150 V 300 V 1R10: 300ppm/ 10<R100: 150ppm/ 300 V 100<R10M: 100ppm/ 10M<R22M: 200ppm/ 200 V 400 V 500 V -55 C to +125 C RC0201 RC0402 50 V 5% (E24) 1R22M RC0603 (0201: Max.10M, 0100/1218: Max. 1M) 75V 1% (E24/E96) RC0805 1R10M (0100/1218: Max. 1M) RC1206 RC1210 0.5% (E24/E96) 10R1M Temperature Coefficient of Resistance -55 C to +155 C RC1218 200V RC2512 Rated Current 0.5A Max. Curren 500 V 1R10: 300ppm/ 10<R100: 100ppm/ 100<R10M: 100ppm/ 500V 10M<R22M: 200ppm/ 1A Rated Current 0.5A Max. Curren 1A Rated Current 1A Max. Current 2A Rated Current 1A Max. Current 2A Rated Current 2A Max. Current 5A Rated Current 2A Max. Current 10A Rated Current Jumper<50m RC2010 Jumper Criteria 2A Max. Current 10A Rated Current 6A Max. Current 10A Rated Current 2A Max. Current 10A Rated Current 2A Max. Current 10A www.yageo.com Jun. 07, 2017 V.0 Product specification Chip Resistor Surface Mount RC_P SERIES 5 8 0100 to 2512 FOOTPRINT AND SOLDERING PROFILES For recommended footprint and soldering profiles, please refer to data sheet "Chip resistors mounting" PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PACKING STYLE REEL RC0100 RC0201 RC0402 RC0603 RC0805 RC1206 RC1210 RC1218 RC2010 RC2512 DIMENSION Paper taping reel (R) 7" (178 mm) 20,000 10,000 10,000 5,000 5,000 5,000 5,000 --- --- --- 13" (330 mm) 80,000 50000 50000 20000 20000 20000 20000 --- --- --- 7" (178 mm) 40,000 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- 4,000 4,000 4,000 ESD safe reel (S) Embossed taping reel 7" (178 mm) NOTE For tape and reel specification/dimensions, please refer to data sheet "Chip resistors packing". FUNCTIONAL DESCRIPTION OPERATING TEMPERATURE RANGE RC0402 to RC2512 Range: -55 to +155 (Fig. 5-1) RC0100 to RC0201 Range: -55 to +125 (Fig. 5-2) POWER RATING Each type rated power at 70 C: RC0100=1/32W RC0201=1/20 W RC0402=1/16 W RC0603=1/10W RC0805=1/8W RC1206=1/4W RC1210=1/2W RC1218=1W RC2010=3/4W RC2512=1W Fig. 5-1 Maximum dissipation (P) in percentage of rated poweras a function of the operating ambient temperature (Tamb) RATED VOLTAGE The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V= (PxR ) Where V = Continuous rated DC or AC (rms) working voltage (V) P = Rated power (W) Fig. 5-2 Maximum dissipation (P) in percentage of rated poweras a function of the operating ambient temperature (Tamb) R = Resistance value () www.yageo.com Jun. 07, 2017 V.0 Product specification Chip Resistor Surface Mount RC_P SERIES 6 8 0100 to 2512 TESTS AND REQUIREMENTS Table 8 Test condition, procedure and requirements TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature Coefficient of Resistance (T.C.R.) IEC 60115-1 4.8 At +25/-55 C and +25/+125 C Refer to table 2 Formula: T.C.R= R 2 R1 x 106 (ppm/C) R1( t 2 t1) Where t1=+25 C or specified room temperature t2=-55 C or +125 C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms Life/ Endurance MIL-STD-202G Method 108A IEC 60115-1 4.25.1 At 70 5 for 1,000 hours; RCWV applied for (1%+0.05 ) for D/F tol 1.5 hours on and 0.5 hour off, still air required (3%+0.05 ) for J tol <100mR for jumper High Temperature Exposure MIL-STD-202G Method 108A IEC 60115-1 4.25.3 1,000 hours at maximum operating temperature depending on specification, unpowered. (1%+0.05 ) for D/F tol Moisture Resistance MIL-STD-202G Method 106F IEC 60115-1 4.24.2 Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for (0.5%+0.05 ) for D/F tol (2%+0.05 ) for J tol 10d with 25 C / 65 C 95% R.H, without steps 7a & 7b, unpowered <100mR for jumper (2%+0.05 ) for J tol <50mR for jumper Parts mounted on test-boards, without condensation on parts Humidity Thermal Shock IEC 60115-1 4.37 MIL-STD-202G Method 107G Steady state for 1000 hours at 40 C / 95% R.H. RCWV applied for 1.5 hours on and (1%+0.05 ) for D/F tol 0.5 hour off (2%+0.05 ) for J tol <100mR for jumper -55/+125 (0.5%+0.05 ) for D/F tol Note Number of cycles required is 300 Devices mounted (1%+0.05 ) for J tol <50mR for jumper Maximum transfer time is 20 seconds Dwell time is 15 minutes. Air - Air Short Time Overload IEC 60115-1 4.13 2.5 times RCWV or maximum overload voltage which is less for 5 seconds at room temperature (1%+0.05 ) for D/F tol (2%+0.05 ) for J tol <50mR for jumper No visible damage Board Flex/ Bending IEC 60115-1 4.33 Device mounted or as described only 1 board bending required bending time: 60 5 seconds (1%+0.05 ) for D/F/J Tol <50mR for jumper No visible damage 0100/0201/0402:5mm; 0603/0805:3mm; 1206 and above:2mm www.yageo.com Jun. 07, 2017 V.0 Product specification Chip Resistor Surface Mount RC_P SERIES TEST TEST METHOD PROCEDURE REQUIREMENTS Solderability - Wetting IPC/JEDECJ-STD-002B test B Electrical Test not required Magnification 50X SMD conditions: 1st step: method B, aging 4 hours at 155 C W ell tinned (>95% covered) No visible damage IEC 60068-2-58 7 8 0100 to 2512 dry heat 2nd step: leadfree solder bath at 245 3 C Dipping time: 3 0.5 seconds -Leaching IPC/JEDECJ-STD-002B test D IEC 60068-2-58 -Resistance to Soldering Heat MIL-STD-202F Method 210F IEC 60068-2-58 Leadfree solder ,260C, 30 seconds immersion time No visible damage Condition B, no pre-heat of samples (0.5%+0.05 ) for D/F tol Leadfree solder, 260 C 5, 10 1 seconds immersion time Procedure 2 for SMD: devices fluxed and (1%+0.05 ) for J tol <50mR for jumper No visible damage cleaned with isopropanol www.yageo.com Jun. 07, 2017 V.0 Product specification Chip Resistor Surface Mount RC_P SERIES 0100 to 2512 8 8 REVISION HISTORY REVISION DATE DESCRIPTION POWER TOLERANCE - First issue of RESISTANCE this specificationRANGE 1/10W, 1/5W, 3/10W, 2/5W, 1/2W 5 m R < 100 m 1/8W, 1/4W, 1/3W, 1/2W 4 m R < 100 m 1/4W, 1/2W 3 m R < 100 m Version 0TYPE Aug. 22, 2014 0603 0805 1206 CHANGE NOTIFICATION - TEMPERATURE COEFFICIENT OF RESISTANCE 1/2W, 1W PF The resistors are constructed using outstanding TCR level material, which makes Yageo PF resistors excellent for current sensing application in battery charger circuit & DC-DC converter. The composition of the resistive 2010 material is adjusted to give the approximate required resistance and is covered with a protective coating, which printed with the resistance value. Finally, the three external terminations (Ni / matte Tin) are added, as shown in Fig. 4. 2512 4527 1% 2% 5 m R < 100 m 75 ppm/C 5% 1W, 2W 1 m R < 100 m 3W 1 m R 50 m 2W, 3W, 5W 6 m R < 1 NOTE: 1. PLEASE CONTACT WITH SALES OFFICES, DISTRIBUTORS AND REPRESENTATIVES IN YOUR REGION BEFORE ORDERING " Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any product change will be announced by PCN." www.yageo.com Jun. 07, 2017 V.0