Not for New Design MKT1817 Vishay Roederstein Metallized Polyester Film Capacitors MKT Radial Potted Types FEATURES W max. L max. Marking Compliant to RoHS Directive 2002/95/EC ENCAPSULATION H max. 0.6 Flame retardant plastic case (UL-class 94 V-0), epoxy resin sealed CLIMATIC TESTING ACC. TO IEC 60068-1 0.4 6.0 55/100/56 -1 CAPACITANCE RANGE (E12 SERIES) 5.0 0.4 1000 pF to 1.0 F O 0.5 CAPACITANCE TOLERANCES APPLICATIONS 20 % (M), 10 % (K), 5 % (J) Blocking, bypassing, filtering and timing, high frequency coupling and decoupling for fast digital and analog ICs, interference suppression in low voltage applications. LEADS REFERENCE SPECIFICATIONS Tinned wire RATED TEMPERATURE IEC 60384-2 85 C MARKING Manufacturer's logo/type/C-value/rated/tolerance/date of manufacture OPERATING TEMPERATURE RANGE - 55 C to + 100 C DIELECTRIC PULL TEST ON LEADS Polyester film 30 N in direction of leads according to IEC 60068-2-21 ELECTRODES RELIABILITY Metallized Operational life > 300 000 h Failure rate < 2 FIT (40 C/ 0.5 UR) CONSTRUCTION Extended metallized film DETAIL SPECIFICATION TEST VOLTAGE (ELECTRODE/ELECTRODE) For more detailed data and test requirements contact: dc-film@vishay.com 1.6 x UR for 2 s RATED VOLTAGES (UR) 63 VDC, 100 VDC, 250 VDC, 400 VDC PERMISSIBLE AC VOLTAGES (RMS) UP TO 60 Hz 40 VAC, 63 VAC, 160 VAC, 200 VAC Document Number: 26032 Revision: 18-May-11 For technical questions, contact: dc-film@vishay.com www.vishay.com 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Metallized Polyester Film Capacitors MKT Radial Potted Types Vishay Roederstein COMPOSITION OF CATALOG NUMBER CAPACITANCE (numerically) MULTIPLIER (nF) 0.1 2 1 3 10 4 100 5 Example: 468 = 680 nF MKT 1817 X XX 25 X X TYPE TOLERANCE PACKAGING Un = 06 = 63 V 4 =5% D Ammopack H = 16.5 mm Un = 01 = 100 V 5 = 10 % G Ammopack H = 18.5 mm Un = 25 = 250 V 6 = 20 % F Reel H = 16.5 Dia. 350 mm W Reel H = 18.5 Dia. 350 mm - Bulk Un = 40 = 400 V Note * For detailed tape specifications refer to "Packaging information" www.vishay.com/doc?28139 or end of catalog SPECIFIC REFERENCE DATA DESCRIPTION VALUE Tangent of loss angle: at 1 kHz at 10 kHz at 100 kHz C 0.1 F 80 x 10-4 150 x 10-4 250 x 10-4 0.1 F C x 1.0 F 80 x 150 x 10-4 10-4 - Rated voltage pulse slope (dU/dt)R at Pitch (mm) 63 VDC 100 VDC 250 VDC 400 VDC 5 15 24 44 100 If the maximum pulse voltage is less than the rated voltage higher dU/dt values can be permitted. R between leads, for C 0.33 F and UR 100 V > 15 000 M R between leads, for C 0.33 F and UR > 100 V > 30 000 M RC between leads, for C > 0.33 F and UR 100 V > 5000 s RC between leads, for C > 0.33 F and UR > 100 V > 10 000 s R between interconnecting leads and casing 100 V (foil method) > 30 000 M 1.6 x URDC, 1 min Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s Withstanding (DC) voltage between leads and case 2.0 x URDC, with minimum of 200 VDC; 1 min Maximum application temperature www.vishay.com 2 100 C For technical questions, contact: dc-film@vishay.com Document Number: 26032 Revision: 18-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Metallized Polyester Film Capacitors MKT Radial Potted Types CAPACITANCE CAPACITANCE CODE VOLTAGE CODE 06 63 VDC/40 VAC w h l (mm) (mm) (mm) - VOLTAGE CODE 01 100 VDC/63 VAC w h l (mm) (mm) (mm) - Vishay Roederstein VOLTAGE CODE 25 250 VDC/160 VAC w h l (mm) (mm) (mm) - VOLTAGE CODE 40 400 VDC/200 VAC w h l (mm) (mm) (mm) 2.5 6.0 7.5 1000 pF -210 1500 pF -215 - - - - - - - - - 2.5 6.0 2200 pF -222 - - - - - - - - - 2.5 6.0 7.5 3300 pF -233 - - - - - - 2.5 6.0 7.5 3.0 6.5 7.5 4700 pF -247 - - - - - - 2.5 6.0 7.5 3.5 8.5 7.5 6800 pF -268 - - - - - - 2.5 6.0 7.5 3.5 8.5 7.5 0.01 F -310 - - - - - - 2.5 6.0 7.5 4.5 9.5 7.5 0.015 F -315 - - - - - - 2.5 6.0 7.5 4.5 9.5 7.5 0.022 F -322 - - - 2.5 6.0 7.5 3.0 6.5 7.5 5.5 11.5 7.5 0.033 F -333 - - - 2.5 6.0 7.5 3.5 8.5 7.5 - - - 0.047 F -347 - - - 2.5 6.0 7.5 4.5 9.5 7.5 - - - 0.068 F -368 - - - 2.5 6.0 7.5 4.5 9.5 7.5 - - - 0.10 F -410 2.5 6.0 7.5 3.5 8.5 7.5 5.5 11.5 7.5 - - - 0.15 F -415 3.5 8.5 7.5 4.5 9.5 7.5 - - - - - - 0.22 F -422 3.5 8.5 7.5 5.0 10.0 7.5 - - - - - - 0.33 F -433 4.5 9.5 7.5 5.5 11.5 7.5 - - - - - - 0.47 F -447 5.0 10.0 7.5 - - - - - - - - - 7.5 0.68 F -468 5.0 10.5 7.5 - - - - - - - - - 1.0 F -510 5.5 11.5 7.5 - - - - - - - - - RECOMMENDED PACKAGING PACKAGING CODE TYPE OF PACKAGING HEIGHT (H) (mm) REEL DIAMETER (mm) ORDERING CODE EXAMPLES PITCH 5 D Ammo 16.5 S (1) MKT1817-233-255-D x G Ammo 18.5 S (1) MKT1817-233-255-G x F Reel 16.5 350 MKT1817-233-255-F x W Reel 18.5 350 MKT1817-233-255-W x - Bulk - - MKT1817-233-255 x Note (1) S = box size 55 mm x 210 mm x 340 mm (w x h x l) Document Number: 26032 Revision: 18-May-11 For technical questions, contact: dc-film@vishay.com www.vishay.com 3 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Vishay Roederstein Metallized Polyester Film Capacitors MKT Radial Potted Types MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting on printed-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to "Packaging Information" www.vishay.com/doc?28139 Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board: For pitches 15 mmthe capacitors shall be mechanically fixed by the leads For larger pitches the capacitors shall be mounted in the same way and the body clamped Space Requirements on Printed-Circuit Board The maximum length and width of film capacitors is shown in the drawing: Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned Product height with seating plane as given by "IEC 60717" as reference: hmax. h + 0.3 mm bmax. = b + 0.4 mm Eccentricity Imax. = I + 0.3 mm Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient temperature of 23 C 1 C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % 2 %. For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. www.vishay.com 4 For technical questions, contact: dc-film@vishay.com Document Number: 26032 Revision: 18-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Metallized Polyester Film Capacitors MKT Radial Potted Types Vishay Roederstein Z () Impedance as a function of frequency (typical curve) 10 7 5 3 2 1 2 5 7 10 3300 pF 0.001 F 0.022 F 0.047 F 0.22 F 0.01 47 F 1 F 3 2 0.1 F 0.1 7 5 1000 pF 1 7 5 3 2 2 3 5 7 100 2 3 f (MHz) Capacitance in F 7 5 0. 1 3 VRMS Max. RMS voltage as a function of frequency at Tamb 85 C 102 VRMS Max. RMS voltage as a function of frequency at Tamb 85 C 102 0. 47 2 101 0. 47 101 0. 22 3 0. 22 2 Capacitance in F 7 5 7 7 5 0. 15 1 0. 33 5 1. 0 3 2 3 2 63 VDC 100 102 2 3 5 7 103 2 3 5 7 104 2 3 5 7 105 f (Hz) 100 VDC 100 102 2 3 5 7 103 2 3 5 7 104 2 5 7 105 f (Hz) 3 103 7 5 Capacitance in F 3 2 33 00 102 7 5 0. 1 22 00 7 47 00 5 0. 04 0. 7 02 2 0. 3 2 01 0.0 22 400 VDC 250 VDC 102 10 00 102 0. 01 3 2 10 Capacitance in pF and F 7 5 3 2 1 VRMS Max. RMS voltage as a function of frequency at Tamb 85 C VRMS Max. RMS voltage as a function of frequency at Tamb 85 C 103 1 10 2 3 5 7 103 Document Number: 26032 Revision: 18-May-11 2 3 5 7 104 2 3 5 7 105 f (Hz) 102 2 3 5 7 103 For technical questions, contact: dc-film@vishay.com 2 3 5 7 104 2 3 5 7 105 f (Hz) www.vishay.com 5 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Metallized Polyester Film Capacitors MKT Radial Potted Types Vishay Roederstein INSPECTION REQUIREMENTS Sub-clause numbers of tests and performance requirements refer to the "Sectional Specification, Publication IEC 60384-2 and Specific Reference Data". Group C Inspection SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapters "General data" of this specification 4.3.1 Initial measurements Capacitance Tangent of loss angle: For C 1 F at 10 kHz for C > 1 F at 1 kHz 4.3 Robustness of terminations Method: 1A Solder bath: 280 C 5 C 4.4 Resistance to soldering heat (see note 3) Duration: 10 s Isopropylalcohol at room temperature Method: 2 4.14 Component solvent resistance Immersion time: 5 min 0.5 min Recovery time: Min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 2 % of the value measured initially Tangent of loss angle Increase of tan : 0.003 for: C 1 F or 0.002 for: C > 1 F Compared to values measured in 4.3.1 No visible damage SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance Tangent of loss angle: For C 1 F at 10 kHz for C > 1 F at 1 kHz 4.6 Rapid change of temperature A = - 55 C B = + 100 C 5 cycles Duration t = 30 min Visual examination 4.7 Vibration (see note 3) www.vishay.com 6 No visible damage Mounting: See section "Mounting" of this specification Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s (whichever is less severe) Total duration 6 h For technical questions, contact: dc-film@vishay.com Document Number: 26032 Revision: 18-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Metallized Polyester Film Capacitors MKT Radial Potted Types Vishay Roederstein SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS 4.7.2 Final inspection Visual examination No visible damage 4.9 Shock (see note 3) Mounting: See section "Mounting" of this specification Pulse shape: Half sine Acceleration: 490 m/s2 Duration of pulse: 11 ms 4.9.2 Final measurements Visual examination Capacitance Tangent of loss angle Insulation resistance No visible damage |C/C| 5 % of the value measured in 4.6.1 Increase of tan : 0.003 for: C 1 F or 0.002 for: C > 1 F Compared to values measured in 4.6.1 50 % of values specified in section "Insulation resistance" of this specification SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.10 Climatic sequence 4.10.2 Dry heat Temperature: + 100 C Duration: 16 h 4.10.3 Damp heat cyclic Test Db First cycle Temperature: - 55 C 4.10.4 Cold Duration: 2 h 4.10.6 Damp heat cyclic Test Db remaining cycles 4.10.6.2 Final measurements Voltage proof = URDC for 1 min within 15 min after removal from testchamber Visual examination No breakdown or flash-over No visible damage Legible marking Capacitance |C/C 5 % of the value measured in 4.4.2 or 4.9.3. Tangent of loss angle Increase of tan : 0.005 for: C 1 F or 0.003 for: C > 1 F Compared to values measured in 4.3.1. or 4.6.1 Insulation resistance 50 % of values specified in section "Insulation resistance" of this specification SUB-GROUP C2 4.11 Damp heat steady state 4.11.1 Initial measurements Document Number: 26032 Revision: 18-May-11 56 days; 40 C; 90 % to 95 % RH Capacitance Tangent of loss angle at 1 kHz For technical questions, contact: dc-film@vishay.com www.vishay.com 7 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design MKT1817 Vishay Roederstein Metallized Polyester Film Capacitors MKT Radial Potted Types SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS 4.11.3 Final measurements Voltage proof = URDC for 1 min within 15 min after removal from testchamber Visual examination No breakdown or flash-over Capacitance Tangent of loss angle Insulation resistance No visible damage Legible marking |C/C| 5 % of the value measured in 4.11.1. Increase of tan : 0.005 for: C 1 F or Compared to values measured in 4.11.1. 50 % of values specified in section "Insulation resistance" of this specification SUB-GROUP C3 4.12 Endurance Duration: 2000 h 1.25 x URDC at 85 C 1.0 x URDC at 100 C 4.12.1 Initial measurements Capacitance Tangent of loss angle: For C 1 F at 10 kHz for C > 1 F at 1 kHz 4.12.5 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 5 % compared to values measured in 4.12.1. Tangent of loss angle Increase of tan : 0.003 for: C 1 F or 0.002 for: C > 1 F Compared to values measured in 4.12.1. Insulation resistance 50 % of values specified in section "Insulation resistance" of this specification SUB-GROUP C4 4.13 Charge and discharge 10 000 cycles Charged to URDC Discharge resistance: UR R = -------------------------------------------C x 5 x dU/dt R 4.13.1 Initial measurements Capacitance Tangent of loss angle: For C 1 F at 10 kHz for C > 1 F at 1 kHz 4.13.3 Final measurements Capacitance |C/C| 3 % compared to values measured in 4.13.1. Tangent of loss angle Increase of tan : 0.003 for: C 1 F 0.002 for: C > 1 F Compared to values measured in 4.13.1. Insulation resistance 50 % of values specified in section "Insulation resistance" of this specification www.vishay.com 8 For technical questions, contact: dc-film@vishay.com Document Number: 26032 Revision: 18-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000