First Edition Jun 4, 2002 @ LCD Module Technical Specification for Trial Type No, F-51373GNC-FW-AH Approved by (Production Div) >, F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 1/191.General Specifications Operating Temp. > min, 0C ~max. 50C Storage Temp. : min. -20C ~max. 70C Dot Pixels : 2403 [R.G.B] (W) = 320 (H) dots Dot Size > 0.23 (W) X 0.225 (KH) mm Dot Pitch : 0.24 (W) x 0.24 (H) mm Viewing Area : 59.0 (W) X 80.3 (H) mm Outline Dimensions : 73.0 (W) < 94.4* (H) x 7.3 max. (D}) mm * Without CFL Cable Weight : 62.4g max. LCD Type : CTD-21398 Cold:Cathode Fluorescent Lamp (CFL) < 1 Qrawings : Dimensional Outline UE-310580B F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 2/192.Electrical Specifications 2.1.Absolute Maximum Ratings Vss=0V Parameter Symbol Conditions Min. Max, Units Supply Voltage Voc-Vss - -0.3 7,0 Vv (Logic) Supply Voltage | Vicp-Vss - -0,3 30.0 Vv (LCD Drive) Input Voltage Vl - -0.3 Veo+0.3 V 2.2.DC Characteristics Ta=25C, Vss=0V Parameter Symbol Conditions Min. Typ. Max. Units Supply Voltage Vec-Vss - Vv (Logic) Supply Voltage | Vicp-Vss Vv 7~5,5V V #2. 7~5.5V 0 - 0.2xVcc v Vcc-Vss=3.0V - 0.7 1.1 mA icc Voc-Vss=5.0V - 0.4 0.6 mA Supply Current ILcp Vicp-Vss=24.2V - 3.7 5.6 mA Note 1 Note 1:Checker Pattern F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 3/192.3.AC Characteristics Vec=4.5-5.5V Parameter Symbol Min. Max. Units Shift Clock Period twee 50 - ns Shift Clock H Pulse Width twor 15 - ns Shift Clock L Pulse Width twer 15 . ns Data Setup Time tos 10 - ns Data Hold Time tox 12 - ns Latch Pulse H Pulse Width Twix 15 - ns Shift Clock Rise to Latch Pulse Rise Time tio 0 ns Shift Clock Fall to Latch Pulse Fall Time tsi 30 - ns Latch Pulse Rise to Shift Clock Rise Time tis 25 - ns Latch Pulse Fall to Shift Clock Rise Time tH 25 - ns Input Signal Rise,Fall Time tr, tf - 50 Note.1 ns DISPOFF Removal Time ns DISPOFF Enable Pulse Width Output Delay Time Note.1 : (ick -twekll - twekl)/2-is:the maxi Note.2 : Ci=15p Shift Clock L Pulse Width Data Setup Time Data Hold Time Latch Pulse "H Pulse Width Shift Clock Rise to Latch Pulse Rise Time tio 0 - ns Shift Clock Fall to Latch Pulse Fall Time ts: 50 - ns Latch Pulse Rise to Shift Clock Rise Time tis 30 - ns Latch Pulse Fall to Shift Clock Rise Time tun 30 - ns Input Signal Rise,Fall Time tr, tf - 50 Note.1 ns DISPOFF Riioval Time tso 160 : ns DISPOFF Enable Pulse Width two 1.2 - us Output Delay Time to. - 200 Note.2 ns Note.1 : (tex twekll - twekl)/2 is the maximum in case of high speed operation. Note.2 : CL=15pF F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 4/19Vcc=2.5~3.0V Parameter Symbol Min. Max. Units Shift Clock Period two 82 - ns Shift Clock H Pulse Width tweokx 28 - ns Shift Clock L Pulse Width two 28 - ns Data Setup Time tos 20 - ns Data Hold Time ton 23 - ns Latch Pulse H Pulse Width tween 30 - ns Shift Clock Rise to Latch Pulse Rise Time tio 0 - ns Shift Clock Fall to Latch Pulse Fall Time tsi 65 - ns Latch Pulse Rise to Shift Clock Rise Time tts 30 - ns Latch Pulse Fall to Shift Clock Rise Time tu 30 - ns Input Signal Rise,Fall Time tr, tf - 50 Note.1 ns DISPOFF Removat Time ns DISPOFF Enable Pulse Width us Output Delay Time ns Note.1 : (ck twekil - twekt Note.2 : CL=15p LP \ tsi N tip tis . tLH 7h EWCKE cP / 7 tWCKH \ J | +, tt | M4 +j_ twWokK tos {pH af DO~D7 LAST DATA TOP DATA AX senee \ twoL tsp DISPOFF F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 5/192.4. Timing Chart T=0.04464ms fyp. LP [| PTAA JitLi lit 1 OEHO = NOSOO FLM LP (Reduction) FLM (Reduction} 2.5 SEG anna SEG720 #1 D7 D6 D5 Sree nee Bo 240(RGB)x320 Dots #320 F-513878GNC-FW-AH (AH} No. 2002-S027 OPTREX CORPORATION Page 6/192.6,.Power Supply ON/OFF Sequence 2.6.1.ON Sequence SIGNAL oo a ee SIGNAL = Ox t VLCD! DISPOFF | 2,6.2,.OFF Sequence Ost _.Please maintain the above sequence when.turning.on.and_off.the power supply. of the... module. LEVEL > YCC VSS i vec : VSS + YLCD : SIGNAL + VLCD : DISPOFF lf DISPOFF is supplied to the module while internal alternate signai for LCD driving (M) is unstable, DC component will be supplied te the LCD panel. This may cause damage the LCD module. F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 7/192.7.Lighting Specifications (Only CFL Backlight unit} Ta=26C Parameter Symbot } Conditions Min. Typ. Max. Units |Notes Lamp Veltage Ve - - 280 - Vrms 1 Lamp Current I - 2.0 3.0 4.0 mArms | 2 Starting Voltage Vs - - - TBD Vrms 3 Surface Luminance L IL=3.0mA - 1300 - ed/m* | 4 Average Life TAL IL=3.0mA - 50,000 - hrs 5 Parameter Symbol j Conditions Min. Typ. Max. Units |Notes Luminance of Module} L IL=3.0mA - 70 - cd/m? | 4 Note 1 :The voltage (r.m.s. ) to maintain the electric discharge of the lamp. It is measured after lighting for 3 minutes . Note 2 :The current ( r.m.s. } to flow through the lamp with the electric discharge. It,is measured atter lighting for 3 minutes. Note 3 :The voltage at starting the electric discharge wh from OV. : Note 4 :Surface Luminance is : display surface.after Note 5 ;. <ife is define d gradually ied by the initial data of luminance ft the center of ee as the time when haif or more of the testing CFLs t thay 50% of th initial brightness at continuous operation. C} <= r 5) CFL Testina Cireui F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 8/193.Optical Specifications 3.1,LCD Driving Voltage Parameter Symbol Conditions Min. Typ. | Max. Units Recommended Taz 0C - os TBD Vv LCD Driving Voltage Viep-Vss Ta=25C TBD 24.2 TBD Vv Note 1 Ta=50C TBD - - V Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and response time are not guaranteed over the entire range. 3.2.Optical Characteristics Ta=25C, 1/320 Duty, 1/15 Bias, Von=24.2V (Note 4), 6= 0, o=- Parameter Symbol Conditions Min. Typ. Max. Units Contrast Ratio Note 1 CR O= 0, =- - TBD - Viewing Angle Shownin3.s & Response | Rise Note 2 | ms Decay Nate 3 ms Definition. of Driving Voltage Vop *"Vop=Vcc-Vicp-VBE Assuming that the typical driving waveforms shown below are applied to the LCD Panel at 1/A Duty - 1/B Bias (A: Duty Number, B: Bias Number). Driving voltage Vop is definded as follows. Vop = (Vthi+Vth2) / 2 Vihi: The voltage Vo-p that should provide 70% of the saturation level in the luminance at the segment which the ON signal is applied to. Vith2: The voltage Vo-p that should provide 20% of the saturation level in the luminance at the segment which the OFF signal is applied to. vi sal - ve sa - scene fo AL (8-2) xVo-p/B tL tit tex} 1h . (ON SIGNAL} (OFF SIGNAL} F-51373GNC-FW-AH (AH) No. 2002-5027 OPTREX CORPORATION Page 9/193.3.Definition of Viewing Angle and Optimum Viewing Area *Point + shows the point where contrast ratio is measured. :6= 0, = - *Driving condition : 1/820 Duty, 1/15 Bias, Von=24.2V, fr=70Hz g0 Temperature Charnber Rotation Table (6,4 ) Photometer #1980A WB a tcp | }---- EE EE EEE ETT A Optical Fiber 8) Computer Control Unit & co Waveform Generator Halogen bulb F-51373GNG-FW-AH (AH} No. 2002-S027 OPTREX CORPORATION Page 10/194.1/0 Terminal 4.1.Pin Assignment CN1 No. Symbol Function 1 Vss Power Supply (OV, GND} 2 Vss Power Supply (OV, GND) 3 FLM First Line Marker 4 LP Data Latch Signal 5 cP Clock Signal for Shifting Data 6 DISPOFF Display Control Signal H : Display on L: Display off 7 D7 Data Bus Line 8 D6 Data Bus Line 9 D5 Data Bus Line 10 D4 Data Bus Line 11 Voc Power Supply for Logic 12 D3 Data Bus Line /:N 13 b2 Bata BUS Line / No 14 D 15 16 ewer Supply (OV, GND) i? Zower Suipply for LCD Drive 18 Non-connection 19 Non-connection 20 NC Non-connection 21 NC Non-connection 22 Vss Power Supply (OV, GND) CN2 No. Symbol Function 1 - HV Power Supply for CFL (HOT) NG Non-connection GND Power Supply for CFL (GND) F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 11/194.2.Example of Power Supply It is recommended to apply a potentiometer for the contrast adjust due to the tolerance of the driving voltage and its temperature dependence. 4.3.Block Diagram FLM MODULE ViCD Tr vSS veo [2 VC (4 Veltagge} Ri+R24+VR=10- 20KQ Ril VR Re VLOD Veltage) VSs (0Y Row Driver NT7703 x 2 or equivalent 320 : 320 dots Column Driver NT7704 x 3 or equivalent 3 L. f. M Circuit Bias Circuit f+ ToLsl HV GND CFL Backlight F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 12/195. Test No change on display and in operation under the following test condition. Conditions: Unless otherwise specified, tests will be conducted under the following condition. Temperature: 20+5C Humidity : 65+5% RH tests will be not conducted under functioning state. No, Parameter Conditions Notes 1 High Temperature Operating | 50C22C, 96hrs (operation state) 2 Low Temperature Operating | 0C+2C, 96hrs (operation state) 1 3 High Temperature Storage 70C22C, 96his 2 4 Low Temperature Storage -20C22C, 96hrs 1,2 5 Damp Proof Test 40C+2C,90~95% RH, 96hrs 1,2 6 Vibration Test Total fixed amplitude : 1.4mm 3 Vibration Frequency : 10~55Hz j= 7 Shock Test Dropping method corner dropping Acormer ! once D Edge dropping | B,C,D edge : once B A Face dropping oxen E,F,G face : once Concrete Surface Note 1 :No dew condensation to be observed. Note 2 :The function test shail be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber. Note 3 :Vibration test will be conducted to the product itself without putting it in a container. F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 13/196.Appearance Standards 6.1 Inspection conditions The LCD shall be inspected under 40W white fluorescent light. The distance between the eyes and the sample shall be more than 30cm. All directions for inspecting the sample should be within 45against perpendicular line. 6.2.Definition of applicable Zones _Azone; fo ~~. Bezel Flame B Zone C Zone A Zone : Active display area B Zone : Area from outside of "A Zone" to validity viewing area C Zone : Rest parts A Zone + B Zone = Validity viewing area F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 14/196.3.Standards No. Parameter 1 Black and White Spots, Foreign Substances and LR/AR Coat Bright point Criteria (1) Round Shape zone Acceptable Number Dimension (mm)} A B Cc D=0.10 * * 0.10<Ds0.15 2 * 0.15 <D =< 0.20 1 * 0.20<D 0 * D=(Long+Short)/2 *: Disregard (2) Line Shape Pe Acceptable Number X(mm) Y(mm) A B Cc - Ws0.01 L<2.0 2 Zone Acceptable Number and polarizer) Dimension (mm) A B Cc D=<0.10 * * 0.19< D <0.15 1 * 0.15 <D <0.20 1 * D<0.20 i) * *: Disregard F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 15/19No. Parameter Criteria 3 The Shape of Dot (1) Pin Hole: Dimension Acceptable Number Yk D=0.1 Less than 1 piece / dot less than 3 pieces/ sell ay 0.4<DS0.2 0 D = (Long + Short} /2 (2) Lacking, Deformation C(GAP) B _> a ita Dimension ie Number -eonnected to 4 piece / dot Ageptable Number Disregard 0.10<D $0.15 2 2 0.15<D 0.20 1 Transformation) 0.20<D 0 Color Variation Not to be conspicuous defects. (Without C Zone) Polarizer Scratches,| Not to be conspicuous defects.(Without C zone) Stroke marks 8 Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not defective, 9 Distance between D<0.2 : 20mm or more. (Without C Zone) Substance Defects 10 Overcoat Pin Hole | D<0.4 Disregard 0.4<D<0.6 2 pieces F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 16/197.Code System of Production Lot The production lot of module is specified some of the following. oooood | Factory Number (Numeral) Factory Code (Aiphabet) Production Week (1~5) Production Month (1~9, X, , 2 Production Year (Lower 2 digits) | Factory Number (Numeral) Production Day of the Week (Sun: A Mon : B~) Factory Code Production Week (1~5} eS Production Month (1~9, X, Y, Production Year (Lower 2 digits follows. 9.Applying Precautions Please contact us when questions and/or new problems not specified in this Specifications arise. F-51373GNC-FW-AH (AH) No. 2002-S027 OPTREX CORPORATION Page 17/1910.Precautions Relating Product Handling The Following precautions will guide you in handling our product correctly. 1} Liquid crystal display devices ~ 1. The liquid crystal dispiay device panel used in the liquid crystal display module is made of plate glass. Avoid any strong mechanical shock. Should the glass break handle it with care, 2. The polarizer adhering to the surface of the LCD is made of a soft material. Guard against scratching it. 2) Care of the liquid crystal display module against static electricity discharge. 1. When working with the module, be sure to ground your body and any electrical equipment you may be using. We strongly recommend the use of anti static mats ( made of rubber ), to protect work tables against the hazards of electrical shock. 2. Avoid the use of work clothing made of synthetic fibers, We recommend cotton clothing or other conductivity-treated fibers. 3. Slowly and carefully remove the protective film from the LCD module, since this operation can generate static electricity. 3) When the LCD module alone must be stored for long periods 1.Protect the modules from high temperature and hy sak out of a damaged LCD module. Should contact with LCD fluid, wash immediately with soap. t guaranteed for models that use metal holders where solder connections between the metal holder and the PCB are not used. Please contact us to discuss appropriate ways to assure conductivity. 7) For models which use CFL: 1.High voltage of 1000V or greater is applied to the CFL cable connector area, Care should be taken not to touch connection areas to avoid burns. 2.Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn. 3.The use of CFLs for extended periods of time at iow temperatures will significantly shorten their service life. ...8).. For. models: which-use touch-panels:-- cee ee ene ee tenes cee atin to ee vnat ete nine tn 1.DBo not stack up modules since they can be damaged by components on 1 neighboring modules. 2.Do not place heavy objects on top of the product. This could cause glass breakage. 9) For models which use COG TAB,or COF: 1.The mechanical strength of the product is low since the IC chip faces out unprotected from the rear. Be sure to protect the rear of the IC chip from external forces, 2.Given the fact that the rear of the IC chip is left exposed, in order to protect the unit trom electrical damage, avoid installation configurations in which the rear of the IC chip runs the risk of making any electrical contact. F-51373GNC-FW-AH (AH) No, 2002-S027 OPTREX CORPORATION Page 18/1910) Madels which use flexible cable, heat seal, or TAB: 1.In order to maintain reliability, do not touch or hold by the connector area. 2,Avoid any bending, pulling, or other excessive force, which can result in broken connections. 11} have an adverse effect on connecting parts (LCD panel-TCP / HEAT SEAL / FPC / etc., PCB-TCP / HEAT SEAL / FPC etc., TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC, etc.,) depending on its materials. Please check and evaluate these materials carefully before use. 12) In case of acrylic plate is attached to front side of LCD panel, cloudiness ( very small cracks ) can occur on acrylic plate, being influenced by some components generated from polarizer film.. Please check and evaluate those acrylic materials carefully before use. 11.Warranty This product has been manufactured to your company's specifications as a part for use in your company's general electronic products, It is guaranteed to perform aecording to 2. We cannot accept responsibility for any defect, which may arise after the application of strong external force to the product. 3. We cannot accept responsibility for any defect, which may arise due to the application of static electricity after the product has passed your companys acceptance inspection procedures. 4. When the product is in CFL models, CFL service life and brightness will vary According to the performance of the inverter used, leaks, etc. We cannot accept responsibility for product performance, reliability, or defect, which may arise. 5. We cannot accept responsibility for intellectual property of a third party, which may arise through the application of our product to your assembly with exception t those ~~~ issues relating directly to the structure or method of manufacturing of our product. 6. Optrex will not be held responsible for any quality guarantee issue for defect products judged as Optrex-origin longer than 2 (two) years from Optrex production or 1 (one) year from Optrex, Optrex America, Optrex Europe, Display LC delivery which ever comes later. F-51373GNC-FW-AH (AH) No. 2002-8027 OPTREX CORPORATION Page 19/19-CN2 (JST :BHR~-O3VS-1) a a < 240x(R.G.B}x320 DOTS wy oo ~~ ae => wl LD oO ee es mol =O A o NI ht} < s Ou | ! co| || PO.08x(R.G.B)X240 |] 4.220. 4 -0.01=57.59(A.A) B 3.5 59.0(V.A) 1 073.0 a (9.24) " << 0.07 0.01 Hs 10 a ot = - a ] N Ricla SO Co 2 lo uy : _ (0.7)] (71.5 PARTS AREA) S DOT DETAIL (S=20:1) SECTION A-A Pbeaed an BON? /AR sh