MCR01ZZPF2000 - ROHM Co., Ltd.

MCR01

Resistors

Rev.J 1/4

Comp act Thick Film Chip Resistors

MCR01 (1005 size : 1 / 16W)

zFeatures

1) Extremely small light

Area ratio is 60% smaller than that of chip 1608, while weight ratio has been cut 75%.

2) Highly relia ble chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

3) Electrodes not corroded by soldering

Thick film makes the electrodes very strong.

4) Flat surface further facilitates mounting

Mounting can also be automated.

5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.

zRatings

Design an d spec ific at io ns a re s ubj ect to c han ge wit ho ut notic e. Caref u ll y c heck the spec ific ati on sh e et sup plie d with t h e

product before usi ng or ordering it.

0.063W (1 / 16W)

−55°C to +155°C

at 70°C

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

Item Conditions Specifications

Rated power

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

R: Nominal resistance (Ω)

E= P×R

Rated voltage

Limiting element voltage 50V

Operating temperature

Nominal resistance See Table 1.

100

−55 0 70 100 125 155

AMBIENT TEMPERATURE (°C)

POWER LOAD (%)

Fig.1

MCR01

Resistors

Rev.J 2/4

Max. 50mΩ

−55°C to +155°C

Resistance

Rated current

Operating temperature

Jumper type

Resistance tolerance Resistance range

(Ω)Resistance temperature coefficient

(ppm / °C)

Table 1

F (±1%)

J (±5%)

10 to 2.2M

(E24, E96)

(E24)

±100

±200

10 to 10M

1.0 to 9.1 +500 / −250

D (±0.5%)

(E24)

±50

100 to 1M

10 to 91 ±100

zBefore using components in circuit s where they will be exposed to transients such as pulse loads (short–dura tion, high– level loads), be certain to

evaluate the component in the mounted st ate. In addition, the reliability and performance of this component cannot be guaranteed if it is used with

a steady state v oltage that is greater than its rated volt age.

zCharacteristics

Item Test conditions (JIS C 5201-1)

Resistor type

Guaranteed value

Jumper type

Resistance

Variation of resistance

with temperature

Solderability

Damp heat, steady state

Endurance at 70°C

Endurance

Rapid change of

temperature

Bend strength of

the end face plating

Resistance to solvent

Resistance to

soldering heat

Overload ± (2.0%+0.1Ω) Max. 50mΩ

± (1.0%+0.05Ω)

± (3.0%+0.1Ω)

Max. 50mΩ

Max. 100mΩ

J : ±5%

F : ±1%

D : ±0.5%

See Table.1

No remarkable abnormality on the appearance.

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

Without mechanical damage such as breaks.

Max. 50mΩJIS C 5201-1 4.5

JIS C 5201-1 4.8

Measurement : +25 / +125°C

JIS C 5201-1 4.18

Soldering condition : 260±5

°C

Duration of immersion : 10±1s.

JIS C 5201-1 4.24

°C, 93%RH

Test time : 1,000h to 1,048h

± (3.0%+0.1Ω)

± (1.0%+0.05Ω)

Max. 100mΩ

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70

°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

JIS C 5201-1 4.25.3

125

°C

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23±5

°C

, Immersion cleaning, 5±0.5min.

Solvent : 2-propanol

JIS C 5201-1 4.19

Test temp. : −55

°C

to +125

°C

5cyc

JIS C 5201-1 4.33

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235±5

°C

Duration of immersion : 2.0±0.5s.

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 100V

MCR01

Resistors

Rev.J 3/4

zDimensions (Unit : mm)

0.5±0.05

0.2±0.1

0.35±0.05

0.25 +0.05

−0.1

1.0±0.05

No. Material

Resistive element (Oxide metal thick film)

Silver thick film electrode

Nickel electrode

Sn electrode

Alumina substrate

Overcoating (Resin)

zPackaging

Reel Taping

0 2

0 4

0 6

0 8

0 2

0 4

0 6

0 8

ABD

ABCD

Label EIAJ ET-7200B compliant

Bulk case

φD

Thick paper

mount

(Underside paper tape)

Chip resistor Square punchout hole

Heat crimp cover tape

Thick paper

mount

(Underside paper tape)

Chip resistor Square punchout hole

Heat crimp cover tape

Narrow pitch (1mm pitch) version

110±0.7

12±0.1

(Unit : mm)

Slider

Shutter

EIAJ ET-7200B compliant

36 0

−0.2

φD

(Unit : mm)

WFEA

8.0

0.3 3.5

0.05 1.75

0.1 0.7

0.1 1.2

0.1

φ180 0

−1.5 φ60 +1

09 +1.0

0φ13±0.2

4.0±0.1 2.0±0.052.0±0.05 Max. 1.1

φ1.5 +0.1

(Unit : mm)

WFEA

8.0

0.3 3.5

0.05 1.75

0.1 0.7

0.1 1.2

0.1

4.0±0.1 1.0±0.051.0±0.05 Max. 1.1

φ1.5 +0.1

MCR01

Resistors

Rev.J 4/4

zPart No. Explanation

Packaging Specifications Code

CMR0 PMZ J

Resistance tolerance

Part No. Nominal resistance

J±5%

F, D

:4 digits

3 digits

±1%

D±0.5% Resistance code, 3 or 4 digits.

000 denotes jumper type.

Resistance

tolerance Resistance

code

J is also used

for jumper

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

Part No. Resistance tolerance

J(±5%)

Code F(±1%)Packaging specifications Reel

Remarks

−

Narrow pitch taping

Basic ordering unit (pcs)

MZP

MCR01 φ180mm

Paper tape (2mm Pitch)

PZPI

MCR01 −

Bulkcase

ZZP

MCR01

D(±0.5%)10,000

50,000

20,000φ180mm

Paper tape (1mm Pitch)

−

Appendix1-Rev3.0

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM Customer Support System THE AMERICAS / EUROPE / ASIA / JAPAN

www.rohm.com

FAX : +81-75-315-0172

Appendix

Notes

No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM

CO.,LTD.

The content specified herein is subject to change for improvement without notice.

The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you

wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM

upon request.

Examples of application circuits, circuit constants and any other information contained herein illustrate the

standard usage and operations of the Products. The peripheral conditions must be taken into account when

designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specified in this document. However, should

you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no respon-

sibility for such damage.

The technical information specified herein is intended only to show the typical functions of and examples of

application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or

exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility

whatsoever for any dispute arising from the use of such technical information.

The Products specified in this document are intended to be used with general-use electronic equipment or

devices (such as audio visual equipment, office-automation equipment, communication devices, electronic

appliances and amusement devices).

The Products are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or

malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard against the

possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as

derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your

use of any Product outside of the prescribed scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or system

which requires an extremely high level of reliability the failure or malfunction of which may result in a direct

threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,

aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no

responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended

to be used for any such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specified herein that may be controlled under

the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.