LM3687 LM3687 Step-Down DC-DC Converter with Integrated Low Dropout Regulator and Startup Mode Literature Number: SNVS473A LM3687 Step-Down DC-DC Converter with Integrated Low Dropout Regulator and Startup Mode General Description Features The LM3687 is a step-down DC-DC converter with an integrated low dropout Linear Regulator optimized for powering ultra-low voltage circuits from a single Li-Ion cell or 3 cell NiMH/NiCd batteries. It provides a dual output with fixed output voltages and combined load current up to 750mA in post regulation mode or 1100mA in independent mode of operation, over an input voltage range from 2.7V to 5.5V. There are several different fixed output voltage combinations available (refer to table 'Voltage Options'). The Linear Regulator being driven from the fixed output voltage of the buck converter (post regulation) translates to high efficiency. The device offers superior features and performance for mobile phones and similar portable applications with complex power management systems. Automatic intelligent switching between PWM low-noise and PFM low-current mode offers improved efficiency over the full load current range. During full-power operation, a fixed-frequency 1.8MHz (typ.) PWM mode drives loads from ~80mA to 750mA max. Hysteretic PFM mode extends the battery life through reduction of the quiescent current during light loads and system standby. The LM3687 also features internal protection against overtemperature, current overload and under-voltage conditions. Two enable pins allow the separate operation of either the DC-DC or the Linear Regulator alone or both. If the power input voltage for the Linear Regulator VIN_LIN is not sufficiently high (e.g. the DC-DC converter is not enabled or starting up) a startup LDO supplies the Linear Regulator Output from VBATT for 50mA rated load current (Startup Mode). If VIN_LIN is at the required voltage level, the startup LDO is deactivated and the main regulator provides 350mA output current. In shutdown mode (Enable pins pulled low) the device turns off and reduces battery consumption to 0.1A (typ.). The LM3687 is available in a tiny, lead-free (NO PB) 9-bump micro SMD package. A high switching frequency of 1.8MHz (typ.) allows the use of tiny surface-mount components. Only four external components -one inductor and three ceramic capacitors- are required. DC-DC Converter: 750mA maximum load capability 1.8MHz PWM fixed switching frequency (typ.) Automatic PFM/PWM mode switching 27A typ. Quiescent Current Internal synchronous rectification for high efficiency Internal soft start (c) 2008 National Semiconductor Corporation 202101 Dual Rail Linear Regulator: Startup Mode Load transients < 25mVpeak typ. Line transients < 1mVpeak typ. Very Low Dropout Voltage: 82mV typ. at 350mA load current 0.7V VIN_LIN 4.5V 10A typical IQ from VIN_LIN 350mA maximum load capability Combined Common Features: 65A typical Quiescent Current from VBATT if both regulators are enabled 750mA maximum combined load capability in post regulation setup (DC-DC 400mA + Linear Regulator 350mA) 1100mA maximum total load capability in independent mode of operation (DC-DC: 750mA, Linear Regulator: 350mA) Operates from a single Li-Ion cell or 3 cell NiMH/NiCd batteries Only four tiny surface-mount external components required (one inductor, three ceramic capacitors) Small 9-bump micro SMD package Over-temperature, current overload and under-voltage protection Applications Mobile Phones Hand-Held Radios Personal Digital Assistants Palm-top PCs Portable Instruments Battery Powered Devices www.national.com LM3687 Step-Down DC-DC Converter with Integrated Low Dropout Regulator and Startup Mode July 7, 2008 LM3687 Typical Application Circuit 20210101 FIGURE 1. Typical Application Circuit: Linear Regulator as Post Regulator 20210105 FIGURE 2. Typical Application Circuit: Independent Mode of Operation www.national.com 2 LM3687 Connection Diagrams Connection Diagram 9-Bump Thin Micro SMD Package 20210104 Package Mark 20210102 Top View Large Bump, 0.5mm Pitch, See NS Package TLA09 Note:The actual physical placement of the package marking will vary from part to part. The package marking "X" designates the date code. "T" is a NSC internal code for die traceability. Both will vary considerably. "BC" identifies the device (part number, option, etc.) Pin Descriptions Pin Number Pin Name Description A1 PGND Power Ground pin A2 SGND Signal Ground pin A3 VOUT_LIN Voltage Output of the linear regulator B1 SW Switching Node Connection to the internal PFET switch and NFET synchronous rectifier B2 EN_DCDC Enable Input for the DC-DC converter. The DC-DC converter is in shutdown mode if voltage at this pin is < 0.4V and enabled if > 1.0V. Do not leave this pin floating. Please see section 'Enable Combinations'. B3 VIN_LIN Power Supply Input for the linear regulator C1 VBATT Power Supply for the DC-DC output stage and internal circuitry. Connect to the input filter capacitor (see typical application). C2 FB_DCDC Feedback Analog Input for the DC-DC converter. Connect directly to the output filter capacitor. C3 EN_LIN Enable Input for the linear regulator. The linear regulator is in shutdown mode if voltage at this pin is < 0.4V and enabled if > 1.0V. Do not leave this pin floating. Please see section 'Enable Combinations'. Voltage Options DC-DC Converter Output: VOUT_DCDC Linear Regulator Output: VOUT_LIN 1.80V 1.50V 1.80V 1.20V 1.80V * 1.30V * * For availability of these or other output voltage combinations please contact your local NSC sales office 3 www.national.com LM3687 Enable Combinations EN_DCDC EN_LIN Comments 0 0 No Outputs 0 1 Linear Regulator enabled only * 1 0 DC-DC converter enabled only 1 1 DC-DC converter and linear regulator active * * Startup Mode: VIN_LIN must be higher than VOUT_LIN(NOM) + 200mV in order to enable the main regulator (IMAX = 350mA). If VIN_LIN < VOUT_LIN(NOM) + 100mV (100mV hysteresis), the startup LDO (IMAX = 50mA) is active, supplied from VBATT. For example in the typical post regulation application the LDO will remain in startup mode until the DC-DC converter has ramped up its output voltage. Order Information Output Voltage Option VOUT_DCDC 1.80V VOUT_LIN Order Number Package Marking Supplied as Flow LM3687TL-1815 S9 250 units, tape and reel, lead free NOPB 1.50V S9 LM3687TLX-1815 1.80V 1.80V * 3000 units, tape and reel, lead free NOPB LM3687TL-1812 SB 250 units, tape and reel, lead free NOPB LM3687TLX-1812 SB 3000 units, tape and reel, lead free NOPB LM3687TL-1813 tbd 250 units, tape and reel, lead free NOPB LM3687TLX-1813 tbd 3000 units, tape and reel, lead free NOPB 1.20V 1.30V * * For availability or other output voltage combinations please contact your local NSC sales office www.national.com 4 Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (Notes 1, 2) VIN_LIN, VBATT pins: Voltage to GND, VIN_LIN VBATT VIN_LIN pin to VBATT pin Enable pins, Feedback pin, SW pin Continuous Power Dissipation (Note 3) Junction Temperature (TJ-MAX ) Storage Temperature Range Package Peak Reflow Temperature (Pb-free, 10-20 sec.) (Note 4) ESD Rating (Note 5) Human Body Model: Machine Model LM3687 Absolute Maximum Ratings (Notes 2, 1) Input Voltage Range VBATT (Note 12) -0.2V to 6.0V 0.2V (GND-0.2V) to (VBATT+0.2V) with 6.0V max Input Voltage Range VIN_LIN Junction Temperature (TJ) Range Ambient Temperature (TA) Range (Note 6) Internally Limited 150C -65C to + 150C 2.7V to 5.5V (VOUT_LIN(NOM) + 1.5V and VOUT_DCDC(NOM) + 1.0V) (VOUT_LIN(NOM) + 0.25V) to 4.5V -30C to + 125C -30C to + 125C Thermal Properties Junction-to-Ambient Thermal Resistance (JA), for 4 layer board (Note 7) Micro SMD 9 260C 2.0kV 200V 70C/W ESD Caution Notice National Semiconductor recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper ESD handling techniques can result in damage. Electrical Characteristics (Notes 2, 8) Typical values and limits appearing in standard typeface are for TA = 25C. Limits appearing in boldface type apply over the full operating temperature range: -30C TJ +125C. Unless otherwise noted, VIN_LIN = VOUT_LIN(NOM) + 0.3V, VBATT = 3.6V, IOUT_LIN = 1mA, VEN_DCDC = VEN_LIN = VBATT, CVBATT = 4.7F, CVOUT_DCDC = 10F, CVOUT_LIN = 2.2F, CVIN_LIN = 1.0F, L = 2.2H. DC-DC Converter Symbol VFB_DCDC (Note 11) Parameter Conditions Feedback Voltage Accuracy PWM Mode Line Regulation VOUT_DCDC + 1.0V VBATT 5.5V, IOUT_DCDC = 150mA Load Regulation 100mA IOUT_DCDC 750mA Typical Limit Units Min Max -2.5 +2.5 % 0.06 %/V 0.0005 %/mA RDSON(P) Pin-Pin Resistance for PFET 280 500 m RDSON(N) Pin-Pin Resistance for NFET 200 400 m ILIM_DCDC Switch Peak Current Limit Open loop (Note 14) FOSC Internal Oscillator Frequency PWM Mode 5 1172 994 1380 mA 1.8 1.3 2.3 MHz www.national.com LM3687 Linear Regulator, Normal Mode Symbol Parameter VOUT_LIN / VOUT_LIN(NOM) Condition Output Voltage Accuracy In startup and normal mode VOUT_LIN / VIN_LIN VOUT_LIN / Typ Line Regulation Error Limit Units Min Max -1.5 -2.0 1.5 2.0 % % mV/V VIN_LIN = VOUT_LIN(NOM) + 0.3V to 4.5V, VBATT = 4.5V 0.3 1 VBATT = VOUT_LIN(NOM) + 1.5V 0.5 3.1 VBATT (2.7V) to 5.5V VOUT_LIN / mA Load Regulation Error IOUT_LIN = 1mA to 350mA 10 60 V/mA VDO_VIN_LIN IOUT_LIN = 350mA , VBATT = VOUT_LIN(NOM) + 1.5V 85 200 mV Output Voltage Dropout (Note 10) (2.7V) IOUT_LIN = 150mA , VBATT = VOUT_LIN(NOM) + 1.3V (2.7V) IQ_VIN_LIN ISC_LIN 42 100 mV Quiescent Current into IOUT_LIN = 0mA VIN_LIN 10 28 A Shutdown Current into VEN_LIN = 0V VIN_LIN 0.1 1 A Output Current (short circuit) VOUT_LIN = 0V 500 Sine modulated VBATT, f = 10Hz f = 100Hz f = 1kHz 70 65 45 Sine modulated VIN f = 10Hz f = 100Hz f = 1kHz f = 10kHz 80 90 95 85 10Hz - 100kHz 100 VRMS PSRR Power Supply Rejection Ratio mA 350 dB dB EN Output Noise linear regulator VOUT_LIN VIN_LIN = VOUT_LIN(NOM) + 0.3V to Dynamic line transient VOUT_LIN(NOM) + 0.9V response VIN_LIN tr, tf = 10s 1 mVp VBATT = VOUT_LIN(NOM) + 1.5V to Dynamic line transient VOUT_LIN(NOM) + 2.1V response VBATT tr, tf = 10s 15 mVp Dynamic load transient Pulsed load 0 ... 350mA response di/dt = 350mA/1s 30 mVp VOUT_LIN Startup LDO Symbol Parameter Conditions Typical Limit Min IOUT Rated output current ISC_LIN Output Current (short circuit) www.national.com 50 VOUT_LIN = 0V 100 6 Units Max mA 50 mA Symbol IQ_VBATT Parameter Quiescent current into VBATT Limit Conditions Typical EN_LIN = low, EN_DCDC = high, IOUT_DCDC = IOUT_LIN = 0mA, DC-DC is not switching (FB_DCDC forced higher than VOUT_DCDC) 27 EN_LIN = high, EN_DCDC = low 55 A EN_LIN = EN_DCDC = high 65 A Shutdown current into VEN_DCDC = VEN_LIN = 0V VBATT -30C TJ +85C Min Max 60 0.1 5 Units A A Under-Voltage Protection Symbol Parameter Conditions Typical Limit Min Units Max VBATT_UVP Under-Voltage Lockout 2.41 V VBATT_EN System Enable Voltage 2.65 V Enable Pins (EN_DCDC, EN_LIN) Symbol Parameter IEN Enable pin input current VIH Logic High voltage level VIL Logic Low voltage level Conditions Typical Limit Min Max 0.01 1 Units A V 1.0 0.4 V Thermal Protection Symbol Parameter Conditions Typical Limit Min Max Units TSHDN (Note 15) Thermal-Shutdown Temperature 160 C TSHDN Thermal-Shutdown Hysteresis 20 C 7 www.national.com LM3687 System Parameters Supply LM3687 External Components, Recommended Specification Symbol Parameter Conditions Value (Note 13) Limit Min Max 2.2 1.5 10 1.0 0.47 Units CVOUT_LIN Output Capacitance for linear regulator CVIN_LIN Input Capacitance for linear regulator CVBATT Input Capacitance for DC-DC converter 4.7 F CVOUT_DCDC DC-DC converter output filter capacitor 10 F CESR ESR of all capacitors L VIN_LIN is biased separately, not by VOUT_DCDC (no CVIN_LIN needed for post regulation application) 0.003 F F 0.300 Inductance 2.2 H ISAT 1.6 A DCR 200 m Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the SGND pin. Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 160C (typ.) and disengages at TJ = 140C (typ.). Note 4: For detailed soldering specifications and information, please refer to National Semiconductor Application Note 1112: Micro SMD Wafer Level Chip Scale Package (AN-1112). Note 5: The Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. (MIL-STD-883 3015.7) Note 6: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (JA), as given by the following equation: TA-MAX = TJ-MAX-OP - (JA x PD-MAX). Note 7: Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power dissipation exists, special attention must be paid to thermal dissipation issues in board design. Note 8: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Unless otherwise specified, conditions for typ. specifications are: VBATT = 3.6V and TA = 25C. Note 9: Dropout voltage is defined as the input to output voltage differential at which the output voltage falls to 100mV below the nominal output voltage. Note 10: This specification does not apply if the battery voltage VBATT needs to be decreased below the minimum operating limit of 2.7V. Note 11: The parameters in the electrical characteristic table are tested at VBATT = 3.6V unless otherwise specified. For performance over the input voltage range refer to datasheet curves. Note 12: The battery input voltage range recommended for ideal applications performance for the specified output voltages is given as follows: VBATT = 2.7V to 5.5V for 1.0V < VOUT_DCDC < 1.8V; VBATT = (VOUT_DCDC +1V) to 5.5V for 1.8V VOUT_DCDC 1.875V Note 13: The capacitor tolerance should be 30% or better over temperature. The full operating conditions for the application should be considered when selecting a suitable capacitor to ensure that the minimum value of capacitance is always met. Recommended capacitor type is X7R. However, dependent on application, X5R, Y5V, and Z5U can also be used. The shown minimum limit represents real minimum capacitance, including all tolerances and must be maintained over temperature and dc bias voltage (See capacitor section in Applications Hints) Note 14: Refer to datasheet curves for closed loop data and its variation with regards to supply voltage and temperature. Electrical Characteristic table reflects open loop data (FB=0V and current drawn from SW pin ramped up until cycle by cycle current limit is activated). Closed loop current limit is the peak inductor current measured in the application circuit by increasing output current until output voltage drops by 10%. Note 15: The DC-DC converter will only enter thermal shutdown from PWM mode. At light loads -present for PFM mode- no significant contribution to the power dissipation is added by the DC-DC converter. www.national.com 8 LM3687 Block Diagram 20210106 Simplified Block Diagram 9 www.national.com LM3687 Typical Performance Characteristics Unless otherwise specified, typical application (post regulation), VBATT = 3.6V, TA = 25C, enable pins tied to VBATT, VOUT_DCDC = 1.8V, VOUT_LIN = 1.2V IQ_VBATT vs. VBATT, LDO disabled IQ_VBATT vs. VBATT, both enabled 20210109 20210110 VOUT_DCDC vs. IOUT_DCDC VOUT_LIN vs. IOUT_LIN 20210111 20210112 VOUT_DCDC vs. Temperature VOUT_LIN vs. Temperature 20210114 20210113 www.national.com 10 LM3687 Efficiency DC-DC vs. Output Current LDO disabled Startup into no load 20210115 20210134 Startup into load VBATT Line Transient Response (PWM Mode) 20210116 VIN_LIN Line Transient Response 20210117 Load Transient Response DC-DC (PWM Mode: 100mA to 750mA) 20210118 20210119 11 www.national.com LM3687 Load Transient Response DC-DC (PFM Mode: 1mA to 50mA) Load Transient Response Linear Regulator 0mA to 350mA 20210120 20210121 Mode Change by Load Transients (PFM to PWM) Mode Change by Load Transients (PWM to PFM) 20210122 20210123 Output Ripple PFM Mode Output Ripple PWM Mode 20210135 www.national.com 12 20210136 DEVICE INFORMATION The LM3687 incorporates a high efficiency synchronous switching step-down DC-DC converter and a very low dropout linear regulator. The DC-DC converter delivers a constant voltage from a single Li- Ion battery and input voltage rails from 2.7V to 5.5V to portable devices such as cell phones and PDAs. Using a voltage mode architecture with synchronous rectification, it has the ability to deliver up to 750mA load current depending on the input voltage, output voltage, ambient temperature and the inductor chosen. The linear regulator delivers a constant voltage biased from VIN_LIN power input - typically the output voltage of the DC-DC converter is used (post regulation) - with a maximum load current of 350mA. Two enable pins allow the independent control of the two outputs. Shutdown mode turns off the device, offering the lowest current consumption (ISHUTDOWN = 0.1 A typ). Besides the shutdown feature, for the DC-DC converter there are two more modes of operation depending on the current required: - PWM (Pulse Width Modulation), and - PFM (Pulse Frequency Modulation). The device operates in PWM mode at load current of approximately 80 mA or higher. Lighter load currents cause the device to automatically switch into PFM for reduced current consumption (IQ_VBATT = 27 A typ) and a longer battery life. Additional features include soft-start, startup mode of the linear regulator, under-voltage protection, current overload protection, and over-temperature protection. As shown in Figure 1: 'Typical Application Circuit: Linear Regulator as Post Regulator', only four external surface-mount components are required for implementation -one inductor and three ceramic capacitors. An internal reference generates 1.8V biasing an internal resistive divider to create a reference voltage range from 0.45V to 1.8V (in 50mV steps) for the linear regulator (depending on the output voltage setting defined in the fab) and the 0.5V reference used for the DC-DC converter. The Under-voltage lockout feature enables the device to startup once VBATT has reached 2.65V typically and turns the device off if VBATT drops below 2.41V typically. Note: In the case that the DC-DC converter is switched off while the Linear Regulator is still enabled, an overshoot of up to 150mV might appear at VOUT_LIN, if all of the following conditions are present: -high VBATT -down ramp on VIN_LIN of greater than 100mV/16us taking the Linear Regulator into dropout -light load on Linear Regulator PWM Operation During PWM (Pulse Width Modulation) operation the converter operates as a voltage-mode controller with input voltage feed forward. This allows the converter to achieve good load and line regulation. The DC gain of the power stage is proportional to the input voltage. To eliminate this dependency, feed forward inversely proportional to the input voltage is introduced. While in PWM mode, the output voltage is regulated by switching at a constant frequency and then modulating the energy per cycle to control power to the load. At the beginning of each clock cycle the PFET switch is turned on and the inductor current ramps up until the duty-cycle-comparator trips and the control logic turns off the switch. The current limit comparator can also turn off the switch in case the current limit of the PFET is exceeded. Then the NFET switch is turned on and the inductor current ramps down. The next cycle is initiated by the clock turning off the NFET and turning on the PFET. 20210124 FIGURE 3. Typical PWM Operation Internal Synchronous Rectification While in PWM mode, the DC-DC converter uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier diode. DC-DC CONVERTER OPERATION During the first part of each switching cycle, the control block in the LM3687 turns on the internal PFET switch. This allows current to flow from the input VBATT through the switch pin SW and the inductor to the output filter capacitor and load. The inductor limits the current to a ramp with a slope of (VBATT VOUT_DCDC) / L, by storing energy in the magnetic field. During the second part of each cycle, the controller turns the PFET switch off, blocking current flow from the input, and then Current Limiting A current limit feature allows the LM3687 to protect itself and external components during overload conditions. PWM mode implements current limiting using an internal comparator that 13 www.national.com LM3687 turns the NFET synchronous rectifier on. The inductor draws current from ground through the NFET to the output filter capacitor and load, which ramps the inductor current down with a slope of (- VOUT_DCDC / L). The output filter stores charge when the inductor current is high, and releases it when low, smoothing the voltage across the load. The output voltage is regulated by modulating the PFET switch on time to control the average current sent to the load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the switch and synchronous rectifier at the SW pin to a low-pass filter formed by the inductor and output filter capacitor. The output voltage is equal to the average voltage at the SW pin. Operation Description LM3687 during PWM operation, allowing additional headroom for voltage drop during a load transient from light to heavy load. The PFM comparators sense the output voltage via the feedback pin and control the switching of the output FETs such that the output voltage ramps between ~0.6% and ~1.7% above the nominal PWM output voltage. If the output voltage is below the `high' PFM comparator threshold, the PMOS power switch is turned on. It remains on until the output voltage reaches the `high' PFM threshold or the peak current exceeds the IPFM level set for PFM mode. The typical peak current in PFM mode is: IPFM = 134mA + VBATT / 23. Once the PMOS power switch is turned off, the NMOS power switch is turned on until the inductor current ramps to zero. When the NMOS zero-current condition is detected, the NMOS power switch is turned off. If the output voltage is below the `high' PFM comparator threshold (see Figure 5), the PMOS switch is again turned on and the cycle is repeated until the output reaches the desired level. Once the output reaches the `high' PFM threshold, the NMOS switch is turned on briefly to ramp the inductor current to zero and then both output switches are turned off and the part enters an extremely low power mode. Quiescent supply current during this `sleep' mode is 27A (typ), which allows the part to achieve high efficiency under extremely light load conditions. If the load current should increase during PFM mode (see Figure 5) causing the output voltage to fall below the `low2' PFM threshold, the part will automatically transition into fixedfrequency PWM mode. When VBATT =2.7V the part transitions from PWM to PFM mode at ~30mA output current and from PFM to PWM mode at ~80mA , when VBATT=3.6V, PWM to PFM transition happens at ~60mA and PFM to PWM transition happens at ~90mA, when VBATT =5.5V, PWM to PFM transition happens at ~100mA and PFM to PWM transition happens at ~125mA. trips at 1172 mA (typ). If the output is shorted to ground the device enters a timed current limit mode where the NFET is turned on for a longer duration until the inductor current falls below a low threshold. This allows the inductor current more time to decay, thereby preventing runaway. PFM Operation At very light load, the DC-DC converter enters PFM mode and operates with reduced switching frequency and supply current to maintain high efficiency. The part automatically transitions into PFM mode when either of two conditions occurs for a duration of 32 or more clock cycles: A. The NFET current reaches zero. B. The peak PMOS switch current drops below the IMODE level, (typically IMODE < 36mA + VBATT / 35 ). 20210125 FIGURE 4. Typical PFM Operation During PFM operation, the DC-DC converter positions the output voltage slightly higher than the nominal output voltage 20210126 FIGURE 5. Operation in PFM Mode and Transfer to PWM Mode www.national.com 14 LINEAR REGULATOR OPERATION In the typical post regulation application the power input voltage VIN_LIN for the linear regulator is generated by the DC-DC converter. Using a buck converter to reduce the battery voltage to a lower input voltage for the linear regulator translates to higher efficiency and lower power dissipation. It's also possible to operate the linear regulator independent of the DC-DC converter output voltage either from VBATT or a different source. In this case it's important that VIN_LIN does not exceed VBATT at any time. VBATT is needed for the linear regulator as well, it supplies internal circuitry. An input capacitor of 1F at VIN_LIN needs to be added if no other filter or bypass capacitor is present in the VIN_LIN path. Startup Mode If the linear regulator is enabled (logic high at EN_LIN), the power input voltage VIN_LIN is continuously compared to the nominal output voltage of the linear regulator VOUT_LIN. If VIN_LIN > VOUT_LIN(NOM) + 200mV the main regulator is active, offering a rated output current of 350mA and supplied by VIN_LIN. If VIN_LIN < VOUT_LIN(NOM) + 100mV the startup LDO is active, providing a reduced rated output current of 50mA typical, supplied by VBATT. Between these two levels a hystersis of 100mV is established. This feature is intended to enable the supply of loads at the output of the linear regulator while the output of the DC-DC converter is still ramping up. In the typical post regulation application with both enable pins connected to VBATT and VIN_LIN supplied by VOUT_DCDC as an 20210132 FIGURE 6. Startup Sequence, VEN_DCDC = VEN_LIN = VBATT Current Limiting The LM3687 incorporates also a current limit feature for the linear regulator to protect itself and external components during overload conditions at VOUT_LIN. In the event of a peak over-current condition at VOUT_LIN the output current through the NFET pass device will be limited. 15 www.national.com LM3687 example, the linear regulator turns on in startup mode (IMAX = 50mA) supplied out of VBATT. At the same time the DC-DC converter turns on, but VOUT_DCDC startup time is longer. The internal signal 'Mode Switch' monitors the voltage level of VIN_LIN. Once VIN_LIN > VOUT_LIN(NOM) + 200mV, the linear regulator changes to normal mode (IMAX = 350mA) supplied out of VIN_LIN. If VIN_LIN drops below VOUT_LIN(NOM) + 100mV the linear regulator switches back to startup mode. Soft Start The DC-DC converter has a soft-start circuit that limits in-rush current during start-up. During start-up the switch current limit is increased in steps. Soft start is activated only if EN_DCDC goes from logic low to logic high after VBATT reaches 2.7V. Soft start is implemented by increasing switch current limit in steps of 85mA, 170mA, 340mA and 1120mA (typical switch current limit). The start-up time thereby depends on the output capacitor and load current demanded at start-up. Typical start-up times with a 10F output capacitor and 750mA load is 455 s and with 1mA load is 180s. LM3687 * * * * Application Hints INDUCTOR SELECTION There are two main considerations when choosing an inductor; the inductor should not saturate, and the inductor current ripple should be small enough to achieve the desired output voltage ripple. Different saturation current rating specifications are followed by different manufacturers so attention must be given to details. Saturation current ratings are typically specified at 25C. However, ratings at the maximum ambient temperature of application should be requested from the manufacturer. The minimum value of inductance to guarantee good performance is 1.76H at ILIM (typ) dc current over the ambient temperature range. Shielded inductors radiate less noise and should be preferred. There are two methods to choose the inductor saturation current rating. * IRIPPLE: average to peak inductor current IOUT_DCDCMAX: maximum load current (750mA) VBATT: maximum input voltage in application L: minimum inductor value including worst case tolerances (30% drop can be considered for method 1) f: minimum switching frequency (1.3MHz) Method 2 A more conservative and recommended approach is to choose an inductor that has a saturation current rating greater than the maximum current limit of 1380mA. A 2.2 H inductor with a saturation current rating of at least 1380mA is recommended for most applications. The inductor's resistance should be less than 0.3 for good efficiency. Table 1 lists suggested inductors and suppliers. For low-cost applications, an unshielded bobbin inductor could be considered. For noise critical applications, a toroidal or shielded- bobbin inductor should be used. A good practice is to lay out the board with overlapping footprints of both types for design flexibility. This allows substitution of a low-noise shielded inductor, in the event that noise from low-cost bobbin models is unacceptable. Method 1 The saturation current should be greater than the sum of the maximum load current and the worst case average to peak inductor current. This can be written as: ISAT > IOUT_DCDC_MAX + IRIPPLE where TABLE 1. Suggested Inductors and their Suppliers Model Vendor Dimensions LxWxH (mm) DCR (max) NR3015T2R2M Taiyo Yuden 3.0 x 3.0 x 1.5 72m LPS3015-222ML Coilcraft 3.0 x 3.0 x 1.5 110m DO3314-222MX Coilcraft 3.3 x 3.3 x 1.4 200m EXTERNAL CAPACITORS As is common with most regulators, the LM3687 requires external capacitors to ensure stable operation. The LM3687 is specifically designed for portable applications requiring minimum board space and the smallest size components. These capacitors must be correctly selected for good performance. INPUT CAPACITOR SELECTION VBATT A ceramic input capacitor of 4.7 F, 6.3V is sufficient for most applications. Place the input capacitor as close as possible to the VBATT pin of the device. A larger value may be used for improved input voltage filtering. Use X7R or X5R types; do not use Y5V. DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0805 and 0603. The minimum input capacitance to guarantee good performance is 2.2F at 3V dc bias; 1.5F at 5V dc bias including tolerances and over ambient temperature range. The input filter capacitor supplies current to the PFET switch of the LM3687 DC-DC converter in the first half of each cycle and reduces voltage ripple imposed on the input power source. A ceramic capacitor's low ESR provides the best noise filtering of the input voltage spikes due to this rapidly changing current. Select a capacitor with sufficient ripple current rating. The input current ripple can be calculated as: www.national.com VIN_LIN If the linear regulator is used as post regulation no additional capacitor is needed at VIN_LIN as the output filter capacitor of the DC-DC converter is close by and therefore sufficient. In case of independent use, a 1.0F ceramic capacitor is recommended at VIN_LIN if no other filter capacitor is present in the VIN_LIN supply path. This capacitor must be located a distance of not more than 1 cm from the VIN_LIN input pin and returned to a clean analogue ground. Any good quality ceramic, tantalum, or film capacitor may be used at this input. Important Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a low-impedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at this input, it must be guaranteed by the 16 CAPACITOR CHARACTERISTICS The LM3687 is designed to work with ceramic capacitors on the outputs to take advantage of the benefits they offer. For capacitance values in the range of 1F to 4.7F, ceramic capacitors are the smallest, least expensive and have the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of a typical 1F ceramic capacitor is in the range of 3m to 40m, which easily meets the ESR requirement for stability for the LM3687. For both input and output capacitors, careful interpretation of the capacitor specification is required to ensure correct device operation. The capacitor value can change greatly, depending on the operating conditions and capacitor type. In particular, the output capacitor selection should take account of all the capacitor parameters, to ensure that the specification is met within the application. The capacitance can vary with DC bias conditions as well as temperature and frequency of operation. Capacitor values will also show some decrease over time due to aging. The capacitor parameters are also dependant on the particular case size, with smaller sizes giving poorer performance figures in general. As an example, the graph below shows a comparison of different capacitor case sizes in a Capacitance vs. DC Bias plot. As shown in the graph, increasing the DC Bias condition can result in the capacitance value falling below the minimum recommended value. It is therefore recommended that the capacitor manufacturers' specifications for the nominal value capacitor are consulted for all conditions, as some capacitor sizes (e.g. 0402) may not be suitable in the actual application. OUTPUT CAPACITOR VOUT_DCDC A ceramic output capacitor of 10 F, 6.3V is sufficient for most applications. Use X7R or X5R types; do not use Y5V. DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0805 and 0603. DC bias characteristics vary from manufacturer to manufacturer and dc bias curves should be requested from them as part of the capacitor selection process. The minimum output capacitance to guarantee good performance is 5.75F at 1.8V DC bias including tolerances and over ambient temperature range. The output filter capacitor smoothes out current flow from the inductor to the load, helps maintain a steady output voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR to perform these functions. The output voltage ripple is caused by the charging and discharging of the output capacitor and by the RESR and can be calculated as: Voltage peak-to-peak ripple due to capacitance can be expressed as follow: Voltage peak-to-peak ripple due to ESR can be expressed as follow: VPP-ESR = (2*IRIPPLE) * RESR Because these two components are out of phase, the rms (root mean squared) value can be used to get an approximate value of peak-to-peak ripple. The peak-to-peak ripple voltage, rms value can be expressed as follow: 20210108 Note that the output voltage ripple is dependent on the inductor current ripple and the equivalent series resistance of the output capacitor (RESR). The RESR is frequency dependent (as well as temperature dependent); make sure the value used for calculations is at the switching frequency of the part. FIGURE 7. Graph Showing a Typical Variation In Capacitance vs. DC Bias The ceramic capacitor's capacitance can vary with temperature. The capacitor type X7R, which operates over a temperature range of -55C to +125C, will only vary the capacitance to within 15%. The capacitor type X5R has a similar tolerance over a reduced temperature range of -55C to +85C. Many large value ceramic capacitors, larger than 1F are manufactured with Z5U or Y5V temperature characteristics. Their capacitance can drop by more than 50% as the temperature varies from 25C to 85C. Therefore X7R is recommended over Z5U and Y5V in applications where the ambient temperature will change significantly above or below 25C. Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more expensive when VOUT_LIN The linear regulator is designed specifically to work with very small ceramic output capacitors. A ceramic capacitor (dielectric types X7R, Z5U, or Y5V) in the 2.2F range (up to 10F) and with an ESR between 3m to 300m is suitable as COUT_LIN in the LM3687 application circuit. This capacitor must be located a distance of not more than 1cm from the VOUT_LIN pin and returned to a clean analogue ground. It is also possible to use tantalum or film capacitors at the device output, VOUT_LIN, but these are not as attractive for reasons of size and cost (see the section Capacitor Characteristics). 17 www.national.com LM3687 manufacturer to have a surge current rating sufficient for the application. The ESR (Equivalent Series Resistance) of this input capacitor should be in the range of 3m to 300m. The tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain 470nF over the entire operating temperature range. LM3687 comparing equivalent capacitance and voltage ratings in the 1F to 4.7F range. Another important consideration is that tantalum capacitors have higher ESR values than equivalent size ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum will increase about 2:1 as the temperature goes from 25C down to -40C, so some guard band must be allowed. For the output capacitor of the DC-DC converter, please note that the output voltage ripple is dependent on the ESR of the output capacitor. TABLE 2. Suggested Capacitors and their Suppliers Capacitance / F Model Voltage Rating Vendor Type Case Size / Inch (mm) 10.0 C1608X5R0J106K 6.3V TDK Ceramic, X5R 0603 (1608) 4.7 C1608X5R1A475K 10V TDK Ceramic, X5R 0603 (1608) 2.2 C1608X5R1A225K 10V TDK Ceramic, X5R 0603 (1608) 1.0 C1005X5R1A105K 10V TDK Ceramic, X5R 0402 (1005) in some circuits, for example CMOS RAM keep-alive applications. POWER DISSIPATION AND DEVICE OPERATION The permissible power dissipation for any package is a measure of the capability of the device to pass heat from the power source, the junctions of the IC, to the ultimate heat sink, the ambient environment. Thus the power dissipation is dependent on the ambient temperature and the thermal resistance across the various interfaces between the die and ambient air. As stated in (Note 6) in the electrical specification section, the allowable power dissipation for the device in a given package can be calculated using the equation: ENABLE OPERATION The outputs of LM3687 may be switched ON or OFF by a logic input at the Enable pins, VEN_DCDC and VEN_LIN. A logic high (related to VBATT) at these pins will turn the outputs on (for information on startup sequence please refer to 'Operation Description'). When both enable pins are low, the outputs are off (pins SW and VOUT_LIN are high impedance) and the device typically consumes 0.1A. If the application does not require the Enable switching feature, the enable pins should be tied to VBATT to keep the outputs permanently on. To ensure proper operation, the signal source used to drive the enable inputs must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under Enable Pins (EN_DCDC, EN_LIN), VIL and VIH. PD_SYS = (TJ(MAX) - TA) / JA For the LM3687 there are two different main sources contributing to the systems power dissipation (PD_SYS): the DCDC converter (PD_DCDC) and the linear regulator (PD_LIN). Neglecting switching losses and quiescent currents these two main contributors can be estimated by the following equations: * PD_LIN = (VIN_LIN - VOUT_LIN) * IOUT_LIN * PD_DCDC = IOUT_DCDC2 * [(RDSON(P) * D) + (RDSON(N) * (1-D))] with duty cycle D = VOUT_DCDC / VBATT. FAST TURN ON For VOUT_LIN fast turn-on is guaranteed by an optimized architecture allowing a fast ramp of the output voltage to reach the target voltage while the inrush current is controlled low at 120mA typical (for a COUT of 2.2F; assuming VIN_LIN is settled before enable happens). As an example, assuming the typical post regulation application, the conversion from VBATT = 3.6V to VOUT_DCDC = 1.8V and further to VOUT_LIN = 1.5V, at maximum load currents, results in following power dissipations: PD_DCDC = (0.75A)2 * (0.38 * 1.8V / 3.6V + 0.25 * (1 - 1.8V / 3.6V)) = 177mW and PD_LIN = (1.8V - 1.5V) * 0.35A = 105mW. PD_SYS = 282mW. With a JA = 70C/W for the micro SMD 9 package this PD_SYS will cause a rise of the junction temperature TJ of: SHORT-CIRCUIT PROTECTION Both outputs of the LM3687 are short circuit protected and in the event of a peak over-current condition, the output current through the MOS transistors will be limited. If the over-current condition exists for a longer time, the average power dissipation will increase depending on the input to output voltage differences until the thermal shutdown circuitry will turn off the MOS transistors. Please refer to the section on power dissipation for calculations. TJ = PD_SYS * JA = 20K. For the same conditions but the linear regulator biased from VBATT, this results in a PD_LIN of 735mW, PD_DCDC = 50mW (because IOUT_DCDC = 400mA) and therefore an increase of TJ of 55K. As lower total power dissipation translates to higher efficiency this example highlights the advantage of the post regulation setup. THERMAL-OVERLOAD PROTECTION Thermal-Overload Protection limits the total power dissipation in the LM3687. When the junction temperature exceeds TJ = 160C typ., the shutdown logic is triggered and the output MOS transistors are turned off, allowing the device to cool down. After the junction temperature dropped by 20C (temperature hysteresis), the output MOS transistors are activated again. This results in a pulsed output voltage during continuous thermal-overload conditions. As the DC-DC converter in PFM mode (low load current) does not contribute significantly to an increase of TJ, it is not turned NO-LOAD STABILITY Both outputs of the LM3687 will remain stable and in regulation with no external load. This is an important consideration www.national.com 18 DC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss in the traces. These can send erroneous signals to the DC-DC converter IC, resulting in poor regulation or instability. Good layout for the LM3687 can be implemented by following a few simple design rules below. Refer to Figure 10 for top layer board layout. 1. Place the LM3687, inductor and filter capacitor close together and make the traces short. The traces between these components carry relatively high switching currents and act as antennas. Following this rule reduces radiated noise. Special care must be given to place the input filter capacitor very close to the VBATT and PGND pin. Place the output capacitor of the linear regulator close to the output pin. 2. Arrange the components so that the switching current loops curl in the same direction. During the first half of each cycle, current flows from the input filter capacitor through the LM3687 and inductor to the output filter capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled up from ground through the LM3687 by the inductor to the output filter capacitor and then back through ground forming a second current loop. Routing these loops so the current curls in the same direction prevents magnetic field reversal between the two half-cycles and reduces radiated noise. 3. Connect the ground pins of the LM3687 and filter capacitors together using generous component-side copper fill as a pseudo-ground plane. Then, connect this to the ground-plane (if one is used) with several vias. This reduces ground-plane noise by preventing the switching currents from circulating through the ground plane. It also reduces ground bounce at the LM3687 by giving it a low impedance ground connection. Route SGND to the ground-plane by a separate trace. 4. Use wide traces between the power components and for power connections to the DC-DC converter circuit. This reduces voltage errors caused by resistive losses across the traces. 5. Route noise sensitive traces, such as the voltage feedback path (FB_DCDC), away from noisy traces between the power components. The voltage feedback trace must remain close to the LM3687 circuit and should be direct but should be routed opposite to noisy components. This reduces EMI radiated onto the DC-DC converter's own voltage feedback trace. A good approach is to route the feedback trace on another layer and to have a ground plane between the top layer and layer on which the feedback trace is routed. 6. Place noise sensitive circuitry, such as radio IF blocks, away from the DC-DC converter, CMOS digital blocks and other noisy circuitry. Interference with noise sensitive circuitry in the system can be reduced through distance. In mobile phones, for example, a common practice is to place the DC-DC converter on one corner of the board, arrange the CMOS digital circuitry around it (since this also generates noise), and then place sensitive preamplifiers and IF stages on the diagonally opposing corner. Often, the sensitive circuitry is shielded with a metal pan and power to it is postregulated to reduce conducted noise, a good field of application for the on-chip low-dropout linear regulator. REVERSE CURRENT PATH There are two body diodes at the switch pin of the DC-DC converter. It is not allowed to pull the switch pin above VBATT or below PGND by more than 200mV. On the main linear regulator there is a bulk switching feature in place preventing the parasitic diode structures from conducting current. This feature is only active as long as any of the regulators is enabled. For the startup LDO, VOUT_LIN must not exceed VBATT. EVALUATION BOARDS For availability of evaluation boards please refer to the Product Folder of LM3687 at www.national.com. For information regarding evaluation boards, please refer to Application Note: AN-1647. Micro SMD PACKAGE ASSEMBLY AND USE Use of the micro SMD package requires specialized board layout, precision mounting and careful re-flow techniques, as detailed in National Semiconductor Application Note 1112. Refer to the section "Surface Mount Technology (SMD) Assembly Considerations". For best results in assembly, alignment ordinals on the PC board should be used to facilitate placement of the device. The pad style used with micro SMD package must be the NSMD (non-solder mask defined) type. This means that the solder-mask opening is larger than the pad size. This prevents a lip that otherwise forms if the soldermask and pad overlap, from holding the device off the surface of the board and interfering with mounting. See Application Note 1112 for specific instructions how to do this. The 9-Bump package used for LM3687 has 300 micron solder balls and requires 275 micron pads for mounting on the circuit board. The trace to each pad should enter the pad with a 90 entry angle to prevent debris from being caught in deep corners. Initially, the trace to each pad should not exceed 183 micron, for a section approximately 183 micron long or longer, as a thermal relief. Then each trace should neck up or down to its optimal width. The important criteria is symmetry. This ensures the solder bumps on the LM3687 re-flow evenly and that the device solders level to the board. In particular, special attention must be paid to the pads for bumps A1, A2, C1 and B3, because PGND, SGND, VBATT and VIN_LIN are typically connected to large copper planes, inadequate thermal relief can result in late or inadequate re-flow of these bumps. The micro SMD package is optimized for the smallest possible size in applications with red or infrared opaque cases. Because the micro SMD package lacks the plastic encapsulation characteristic of larger devices, it is vulnerable to light. Backside metallization and/or epoxy coating, along with frontside shading by the printed circuit board, reduce this sensitivity. However, the package has exposed die edges. In particular, micro SMD devices are sensitive to light, in the red and infrared range, shining on the package's exposed die edges. BOARD LAYOUT CONSIDERATIONS PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DC- 19 www.national.com LM3687 off in case a thermal shutdown is initiated. If the DC-DC converter operates in PWM mode, the PMOS is turned off in case of a thermal shutdown. The Thermal-Overload Protection is designed to protect the LM3687 in the event of a fault condition. For normal, continuous operation, do not exceed the absolute maximum junction temperature rating of TJ = +150C (see Absolute Maximum Ratings). LM3687 20210133 FIGURE 8. Top Layer Board Layout www.national.com 20 LM3687 Physical Dimensions inches (millimeters) unless otherwise noted NS Package Number TLA09BBA The dimensions for X1, X2 and X3 are given as: X1 = 1539m 30m X2 = 1539m 30m X3 = 600m 75m 9-Bump Thin Micro SMD Package, Large Bump, 0.5mm Pitch For most accurate revision please refer to www.national.com/packaging/parts/ 21 www.national.com LM3687 Step-Down DC-DC Converter with Integrated Low Dropout Regulator and Startup Mode Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated