www.RFM.com E-mail: info@rfm.com Page 1 of 2
© 2009-2011 by RF Monolithics, Inc. RO3144A - 8/15/11
Electrical Characteristics
Characteristic Sym Notes Minimum Typical Maximum Units
Frequency, +25 °C RO3144A fC
2,3,4,5
916.300 916.700 MHzRO3144A-1 916.350 916.650
RO3144A-2 916.400 916.600
Tolerance from 916.5 MHz RO3144A
∆fC
±200 kHzRO3144A-1 ±150
RO3144A-2 ±100
Insertion Loss IL 2,5,6 1.2 2.5 dB
Quality Factor Unloaded Q QU5,6,7 6600
50 Ω Loaded Q QL750
Temperature Stability Turnover Temperature TO6,7,8 10 25 40 °C
Turnover Frequency fOfCkHz
Frequency Temperature Coefficient FTC 0.032 ppm/°C2
Frequency Aging Absolute Value during the First Year |fA| 1 <±10 ppm/yr
DC Insulation Resistance between Any Two Terminals 5 1.0 MΩ
RF Equivalent RLC Model Motional Resistance RM5, 6, 7, 9 13.1 Ω
Motional Inductance LM15 µH
Motional Capacitance CM2.1 fF
Shunt Static Capacitance CO5, 6, 9 2.09 pF
Test Fixture Shunt Inductance LTEST 2, 7 14.5 nH
Lid Symbolization RO3144A: 663, RO3144A-1: 897, RO3144A-2: 813, // YWWS
• Ideal for 916.5 MHz Transmitters
• Very Low Series Resistance
• Quartz Stability
• Surface-mount Ceram ic Case
• Complies with Directive 2002/95/EC (RoHS)
The RO3144A is a true one-port, surface-acoustic-wave (SAW) resonator in a surface-mount ceramic case.
It provides reliable, fundamental-mode, qua rtz frequency stabilization of fix ed-frequency transm itters
operating at 916.5 MHz.
Absolute Maximum Ratings
Rating Value Units
CW RF Power Dissipation 0 dBm
DC Voltage Between Terminals ±30 VDC
Case Temperature -40 to +85 °C
Soldering Temperature, 10 seconds / 5 cycles maximum 260 °C
916.5 MHz
SAW
Resonator
RO3144A
RO3144A-1
RO3144A-2
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Frequency agin g is the chang e in fC with time an d is specif ied at +6 5 °C or
less. Aging may exceed the specification for prolonged temperatures
above +65 °C. Typically, aging is greatest the first year after manufacture,
decreasing in subsequent years.
2. The center frequency, fC, is measured at the minimum insertion loss point,
ILMIN, with the res onator in the 50 Ω test system (VSWR ≤ 1.2:1). The
shunt inductance, LTEST, is tuned for paralle l resonance with CO at fC.
Typi cally, fOSCILLATOR or fTRANSMITTER is approximately equal to the
resonator fC.
3. One or more of the following Unite d Sta tes patents apply: 4,454,488 and
4,616,197.
4. Typically, equipment utilizing this device requires emissions testing and
government app roval, which is the responsibilit y of the equipment
manufacturer.
5. Unless noted otherwise, case temperature TC=+25 ± 2 °C.
6. The design, manufacturing process , and specif ications of this device are
subject to change without notice.
7. Derived mat hematically from one or more of the following directly
measured parameters : fC, IL, 3 dB bandwidth, fC versus TC, and CO.
8. Turnover temperature, TO, is the temperature of maximum (or turnover )
frequenc y, fO. The nominal f requency at any case tempera ture, T C, may be
calculated from: f = fO[1 - FTC (TO-TC)2]. Typically oscillator TO is
approximately equal to the specified resonator TO.
9. This equivalent RLC model approximate s resonator pe rformance near the
resonan t frequen cy and is provided for refer ence o nly. The capaci tanc e CO
is the static (nonmotional) capac i tance between the tw o terminals
measured at low frequency (10 MHz) with a cap ac i tance meter. The
measureme nt includes p arasitic cap acitanc e with "NC” pads unconne cted.
Case pa rasitic capacitance is approximat ely 0.05 pF. Transducer parallel
capacitance can by calculated as: CP≈CO-0.05pF.
SM5035-4
Pb