Delta39K™⁄Ultra370 00™ ISR™ Programming K
it
CY390
0i
Cypress Semiconductor Corporation • 3901 North First Street • San Jose,CA 95134 • 408-943-2600
Document #: 38-03009 Rev. *B Revised August 14, 2003
Features
• Supports Cypress’s Ultra37000™, Ultra37000V™,
Delta39K™, and PSI™ families of products
• STAPL programming language support
• Standard JTAG programming interface
• Multi-device programming
• Easy to use Windows 98-™, Windows 2000-™,
Windows ME-™, and Windows NT™-compatible
interface
• Eliminates programming insertion to improve
manufacturing efficiency
• For programming in the lab, on manufacturing floor , or
at remote sites
• ATE support via STAPL on industry leading ATE
platforms
Kit Contents
• UltraISR™ programming cable for use with Ultra37000,
Delt a 39K, and PSI CPLD families
• ISR Programming Software release 3.0
• ISR application notes
• Delta39K/Ultra37000 prototype board[1]
Functional Description
The Delta39K/Ultra37000 ISR Programming Kit enables users
to program Ultra37000, Ultra37000V, Delta39K, and PSI
CPLDs on board with our ISR Programming Software, the
UltraISR Programming Cable, and a personal computer. The
UltraI SR Programmi ng Cable connect s to t he para llel port of a
PC into a standard 10-pin male connector mounted on the
user’s board. The ISR software provides an easy-to-use
Graphical User Interface that accepts JEDEC or.hex files as
input. The JEDEC/.hex files are used to compose platform
independent STAPL files. STAPL files contain all the infor-
mation needed to program the device. The ISR software is
used to define how many devices are in the daisy chain and
what operation is to be done on each Cypress device. The
same chain can be used with other JTAG-compliant devices.
The ISR User’s Guide describes the operation of the ISR
software. The application notes included with the kit describe
all system design considerations for programming with this
Programming K it.
10-pin Programming Connector
The diagram below shows the pinout of the 10-pin male
connector to be mounted onto the board.
The view looking down onto the board connector pins is shown
below.
Notes:
1. Cypress reserves the right to substitute prototype boards based on product availability.
2. Refer to the CD-ROM ISR User’s Guide documentation for detailed information on ISR programming and electrical specification requirements.
TDO VCC ISR[2] JTAGen GND[2]
GND NC TDI TCK TMS
In-System Reprogrammable™ (ISR™) Programming
VCC
Designer’s Board
Parallel Port
10-pin ISR Connector
25-pin
Cable PC
6’
Device
Device
Cypress
Cypress
CY3900
i
Document #: 38-03009 Rev. *B Page 2 of 4
Table 1 describes the function of each of these pins on the
UltraI SR Programm ing Cab le. An OU TPUT is pro vided by the
PC and an INPUT is provided by the target system.
The dimensions of the male connector required for the
UltraISR Programming Cable are given below.
Male Connector
2 x 5 = 2 rows, 5 pins per row
Measuring from center of the pins, each pin is 0.1” from the
others.
Pin length is 0.23”.
Pin cross-section is 0.025” x 0.025”.
Part Number
Digi-Key® S2012-05-ND (straight-pin connector).
Digi-Key S2112-05-ND (right-angle connector).
To facilitate easy and quick prototyping of designs, a
Delta39K/Ultra37000 Prototype Board[3] has be en i nc lud ed in
the CY3900i Delta39/Ultra37000 ISR Programming Kit. The
prototype board comes with a CY37256VP160 device and a
CY39100V208 device already premounted and header strips
that facilitate signal testing. Detailed information on the board
layout and proper usage may be found in the Cypress appli-
cation note, Using the Delta39K ISR Prototype Board.
Note:
3. See Figure 1 for the basic layout.
Table 1. UltraISR Cable Pin Descriptions
Pin Type Description
JTAGen OUTPUT In System Reprogramming JTAG Enable (active HIGH).
ISR* OUTPUT In System Reprogramming Enable Indicator (active LOW).
VCC INPUT +5V and +3.3V Supply Voltage provided from the target system to the cable.
TDO INPUT T est Data Output Receiver . The TDO outpu t pin o f the la st device i n the I SR ch ain of
the system is connected to this input pin.
TMS OUTPUT Test Mode Control. This is the mode select control input for the TAP controller state
machine contained in the ISR interface.
TCK OUTPUT Test Clock. ISR interface clock.
TDI OUTPUT Test Dat a Input Driver . This output pin is connect ed to the TDI input of the first devic e
in the ISR chain.
NC NC No Connect.
GND —Zero volt common ground for PC and target system.
Figure 1. Delta39K™/Ultra37000™ Prototype Board
160-pin
TQFP
LED VCC GND
VCCO GND
Heade
r
Strips
Power
Connecto
r
Power
Connecto
r
CY39100V208
208-pin
TQFP
Header Strips
ISR 10-pin
Connector 10-pin
Connector
J2 J3
Daisy Chain Jum p ers
CY37256VP160
CY3900
i
Document #: 38-03009 Rev. *B Page 3 of 4
© Cypress Semiconductor Corporation, 2003. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any ci rcuitry other th an circuitry embod ied in a Cypr ess Semiconductor pr oduct. Nor does it convey or imply any licen se under p atent or other rights. C ypress Semicond uctor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
PC System Requirements
• IBM PC or compatible running Windows 98, Windows 98
Second Edition, Windows ME, Windows NT 4.0 Service
Pack 5 or later or Windows 2000 Service Pack 1 or later.
• One free parallel port.
• A minimum of 32 MB of RAM.
• Approximately 30 MB of free hard disk space.
Ordering Information
Windows 98, Windows ME, Windows 2000, and Windows NT are trademarks of Microsoft Corporation. Digi-Key is a registered
trademark of Digi-Key Corpo ration. I SR, UltraISR, Ultra37000, Delta39K, and PSI are trademarks of Cypress Semiconductor.
Product
Code Description
CY3900i Delta39K/Ultra37000 ISR Programming Kit
CY3900
i
Document #: 38-03009 Rev. *B Page 4 of 4
Document History Page
Document Title: Delta39K™/Ultra37000™ ISR™ Programming Kit
Document Number: 38-03009
REV. ECN NO. Issue
Date Orig. of
Change Description of Change
** 108980 08/07/01 HOW New Data Sheet
*A 111228 01/23/02 CNH Removed references to Windows 95
*B 127867 08/18/03 FSG Removed Quantum38K from all pages
