May 31, 2012 3A, 2A and 1A High Voltage High-Side and Low-Side Gate Drivers General Description The LM5100A/B/C and LM5101A/B/C High Voltage Gate Drivers are designed to drive both the high-side and the lowside N-Channel MOSFETs in a synchronous buck or a halfbridge configuration. The floating high-side driver is capable of operating with supply voltages up to 100V. The "A" versions provide a full 3A of gate drive while the "B" and "C" versions provide 2A and 1A respectively. The outputs are independently controlled with CMOS input thresholds (LM5100A/B/C) or TTL input thresholds (LM5101A/B/C). An integrated high voltage diode is provided to charge the high-side gate drive bootstrap capacitor. A robust level shifter operates at high speed while consuming low power and providing clean level transitions from the control logic to the high-side gate driver. Under-voltage lockout is provided on both the low-side and the high-side power rails. These devices are available in the standard SOIC-8 pin, PSOP-8 pin and the LLP-10 pin packages. The LM5100C and LM5101C are also available in eMSOP-8 package. The LM5101A is also available in LLP-8 pin package. Features Drives both a high-side and low-side N-Channel MOSFETs Independent high and low driver logic inputs Bootstrap supply voltage up to 118V DC Fast propagation times (25 ns typical) Drives 1000 pF load with 8 ns rise and fall times Excellent propagation delay matching (3 ns typical) Supply rail under-voltage lockout Low power consumption Pin compatible with HIP2100/HIP2101 Typical Applications Current Fed push-pull converters Half and Full Bridge power converters Synchronous buck converters Two switch forward power converters Forward with Active Clamp converters Package SOIC-8 PSOP-8 LLP-8 (4 mm x 4 mm) LLP-10 (4 mm x 4 mm) eMSOP-8 Simplified Block Diagram 20203103 FIGURE 1. (c) 2012 Texas Instruments Incorporated 202031 SNOSAW2O www.ti.com LM5100A/B/C, LM5101A/B/C 3A, 2A and 1A High Voltage High-Side and Low-Side Gate Drivers LM5100A/B/C LM5101A/B/C LM5100A/B/C, LM5101A/B/C Input/Output Options Part Number Input Thresholds Peak Output Current LM5100A CMOS 3A LM5101A TTL 3A LM5100B CMOS 2A LM5101B TTL 2A LM5100C CMOS 1A LM5101C TTL 1A Connection Diagrams 20203101 20203137 20203102 20203135 20203136 www.ti.com 2 Ordering Number Package Type NSC Package Drawing Supplied As LM5100A/LM5101AM SOIC 8 M08A 95 units shipped in anti static rails LM5100A/LM5101AMX SOIC 8 M08A 2500 shipped in Tape & Reel LM5100A/LM5101AMR PSOP 8 MRA08A 95 units shipped in anti static rails LM5100A/LM5101AMRX PSOP 8 MRA08A 2500 shipped in Tape & Reel 1000 shipped in Tape & Reel LM5100A /LM5101ASD LLP 10 SDC10A LM5100A/LM5101ASDX LLP 10 SDC10A 4500 shipped in Tape & Reel LM5100B/LM5101BMA SOIC 8 M08A 95 units shipped in anti static rails LM5100B/LM5101BMAX SOIC 8 M08A 2500 shipped in Tape & Reel LM5100B/LM5101BSD LLP 10 SDC10A 1000 shipped in Tape & Reel LM5100B/LM5101BSDX LLP 10 SDC10A 4500 shipped in Tape & Reel LM5100C/LM5101CMA SOIC 8 M08A 95 units shipped in anti static rails LM5100C/LM5101CMAX SOIC 8 M08A 2500 shipped in Tape & Reel LM5100C /LM5101CSD LLP 10 SDC10A 1000 shipped in Tape & Reel LM5100C/LM5101CSDX LLP 10 SDC10A 4500 shipped in Tape & Reel LM5100C/LM5101CMYE eMSOP-8 MUY08A 250 shipped in Tape & Reel LM5100C/LM5101CMY eMSOP-8 MUY08A 1000 shipped in Tape & Reel LM5100C/LM5101CMYX eMSOP-8 MUY08A 3500 shipped in Tape & Reel LM5101ASD-1 LLP 8 SDC08A 1000 shipped in Tape & Reel LM5101ASDX-1 LLP 8 SDC08A 4500 shipped in Tape & Reel 3 www.ti.com LM5100A/B/C, LM5101A/B/C Ordering Information LM5100A/B/C, LM5101A/B/C Pin Descriptions Pin # SOIC-8 PSOP-8 LLP-8 LLP-10 eMSOP-8 1 1 1 1 1 Name VDD Description Application Information Positive gate drive supply Locally decouple to VSS using low ESR/ESL capacitor located as close to the IC as possible. 2 2 2 2 2 HB High-side gate driver bootstrap rail Connect the positive terminal of the bootstrap capacitor to HB and the negative terminal to HS. The bootstrap capacitor should be placed as close to the IC as possible. 3 3 3 3 3 HO High-side gate driver output Connect to the gate of high-side MOSFET with a short, low inductance path. 4 4 4 4 4 HS High-side MOSFET source connection Connect to the bootstrap capacitor negative terminal and the source of the high-side MOSFET. High-side driver control input The LM5100A/B/C inputs have CMOS type thresholds. The LM5101A/B/C inputs have TTL type thresholds. Unused inputs should be tied to ground and not left open. 5 5 5 7 5 HI 6 6 6 8 6 LI Low-side driver control input The LM5100A/B/C inputs have CMOS type thresholds. The LM5101A/B/C inputs have TTL type thresholds. Unused inputs should be tied to ground and not left open. 7 7 7 9 7 VSS Ground return All signals are referenced to this ground. 8 8 8 10 8 LO Low-side gate driver output Connect to the gate of the low-side MOSFET with a short, low inductance path. EP EP EP EP EP (LLP and PSOP and eMSOP packages) Solder to the ground plane under the IC to aid in heat dissipation. Note: For LLP-8, LLP-10 and eMSOP-8 package, it is recommended that the exposed pad on the bottom of the package is soldered to ground plane on the PC board, and that ground plane should extend out from beneath the IC to help dissipate heat. For LLP-10 package, pins 5 and 6 have no connection. www.ti.com 4 If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. VDD to VSS HB to HS LI or HI Input LO Output HO Output HS to VSS (Note 6) HB to VSS +150C -55C to +150C 2 kV Recommended Operating Conditions -0.3V to +18V -0.3V to +18V -0.3V to VDD +0.3V -0.3V to VDD +0.3V VHS -0.3V to VHB +0.3V -5V to +100V 118V VDD HS HB HS Slew Rate Junction Temperature +9V to +14V -1V to 100V VHS +8V to VHS +14V < 50 V/ns -40C to +125C Electrical Characteristics Limits in standard type are for TJ = 25C only; limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified, VDD = VHB = 12V, VSS = VHS = 0V, No Load on LO or HO (Note 4). Symbol Parameter Conditions Min Typ Max Units SUPPLY CURRENTS IDD VDD Quiescent Current, LM5100A/B/C LI = HI = 0V 0.1 0.2 VDD Quiescent Current, LM5101A/B/C LI = HI = 0V 0.25 0.4 IDDO VDD Operating Current f = 500 kHz 2.0 3 mA IHB Total HB Quiescent Current LI = HI = 0V 0.06 0.2 mA IHBO Total HB Operating Current f = 500 kHz 1.6 3 mA IHBS HB to VSS Current, Quiescent HS = HB = 100V 0.1 10 IHBSO HB to VSS Current, Operating f = 500 kHz 0.4 mA A mA INPUT PINS VIL Input Voltage Threshold LM5100A/B/C Rising Edge 4.5 VIL Input Voltage Threshold LM5101A/B/C Rising Edge 1.3 VIHYS Input Voltage Hysteresis LM5100A/B/C VIHYS Input Voltage Hysteresis LM5101A/B/C RI Input Pulldown Resistance 5.4 6.3 1.8 2.3 500 V V mV 50 mV 100 200 400 k 6.0 6.9 7.4 V UNDER VOLTAGE PROTECTION VDDR VDD Rising Threshold VDDH VDD Threshold Hysteresis VHBR HB Rising Threshold VHBH HB Threshold Hysteresis 0.5 5.7 6.6 V 7.1 0.4 V V BOOT STRAP DIODE VDL Low-Current Forward Voltage IVDD-HB = 100 A 0.52 0.85 V VDH High-Current Forward Voltage IVDD-HB = 100 mA 0.8 1 V RD Dynamic Resistance LM5100A/B/C, LM5101A/B/ IVDD-HB = 100 mA C 1.0 1.65 0.12 0.25 LO & HO GATE DRIVER VOL VOH Low-Level Output Voltage LM5100A/LM5101A Low-Level Output Voltage LM5100B/LM5101B 0.16 0.4 Low-Level Output Voltage LM5100C/LM5101C 0.28 0.65 0.24 0.45 0.28 0.60 0.60 1.10 High-Level Output Voltage LM5100A/LM5101A High-Level Output Voltage LM5100C/LM5101C IHO = ILO = 100 mA VOH = VDD- LO or VOH = HB - HO Peak Pullup Current LM5100A/LM5101A HO, LO = 0V High-Level Output Voltage LM5100B/LM5101B IOHL IHO = ILO = 100 mA V 3 Peak Pullup Current LM5100B/LM5101B 2 Peak Pullup Current LM5100C/LM5101C 1 5 V A www.ti.com LM5100A/B/C, LM5101A/B/C Junction Temperature Storage Temperature Range ESD Rating HBM (Note 2) Absolute Maximum Ratings (Note 1) LM5100A/B/C, LM5101A/B/C Symbol IOLL Parameter Peak Pulldown Current LM5100A/LM5101A Conditions Min Typ HO, LO = 12V Max Units 3 Peak Pulldown Current LM5100B/LM5101B 2 Peak Pulldown Current LM5100C/LM5101C 1 A THERMAL RESISTANCE JA Junction to Ambient SOIC-8 170 LLP-8(Note 3) 40 LLP-10 (Note 3) 40 PSOP-8 40 eMSOP-8 (Note 3) 80 C/W Switching Characteristics Limits in standard type are for TJ = 25C only; limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified, VDD = VHB = 12V, VSS = VHS = 0V, No Load on LO or HO (Note 4). Symbol tLPHL Parameter Typ Max 20 45 22 56 20 45 26 56 20 45 22 56 20 45 LO Turn-On Propagation Delay LM5101A/B/C 26 56 Delay Matching: LO on & HO off LM5100A/B/C 1 10 Delay Matching: LO on & HO off LM5101A/B/C 4 10 Delay Matching: LO off & HO on LM5100A/B/C 1 10 Delay Matching: LO on & HO off LM5101A/B/C 4 10 LO Turn-Off Propagation Delay LM5100A/B/C Conditions LI Falling to LO Falling LO Turn-On Propagation Delay LM5100A/B/C LI Rising to LO Rising ns LO Turn-On Propagation Delay LM5101A/B/C tHPHL HO Turn-Off Propagation Delay LM5100A/B/C HI Falling to HO Falling ns HO Turn-Off Propagation Delay LM5101A/B/C tHPLH tMON tMOFF LO Turn-On Propagation Delay LM5100A/B/C HI Rising to HO Rising ns Either Output Rise/Fall Time CL = 1000 pF tR Output Rise Time (3V to 9V) LM5100A/ LM5101A CL = 0.1 F www.ti.com 8 ns 430 ns Output Rise Time (3V to 9V) LM5100B/ LM5101B 570 Output Rise Time (3V to 9V) LM5100C/ LM5101C 990 Output Fall Time (3V to 9V) LM5100A/ LM5101A ns ns tRC, tFC tF Units ns LO Turn-Off Propagation Delay LM5101A/B/C tLPLH Min CL = 0.1 F 260 Output Fall Time (3V to 9V) LM5100B/ LM5101B 430 Output Fall Time (3V to 9V) LM5100C/ LM5101C 715 6 ns Parameter Conditions Min Typ Max Units tPW Minimum Input Pulse Width that Changes the Output 50 ns tBS Bootstrap Diode Reverse Recovery Time IF = 100 mA, IR = 100 mA 37 ns Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: The Human Body Model (HBM) is a 100 pF capacitor discharged through a 1.5k resistor into each pin. 2 kV for all pins except Pin 2, Pin 3 and Pin 4 which are rated at 1000V for HBM. Machine Model (MM) ratings are : 100V(MM) for Options B and C; 50V(MM) for Option A. Note 3: 4 layer board with Cu finished thickness 1.5/1/1/1.5 oz. Maximum die size used. 5x body length of Cu trace on PCB top. 50 x 50mm ground and power planes embedded in PCB. See Application Note AN-1187. Note 4: Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 5: The JA is not a given constant for the package and depends on the printed circuit board design and the operating environment. Note 6: In the application the HS node is clamped by the body diode of the external lower N-MOSFET, therefore the HS node will generally not exceed -1V. However, in some applications, board resistance and inductance may result in the HS node exceeding this stated voltage transiently. If negative transients occur, the HS voltage must never be more negative than VDD-15V. For example if VDD = 10V, the negative transients at HS must not exceed -5V. Typical Performance Characteristics Peak Sourcing Current vs VDD Peak Sinking Current vs VDD 20203128 20203127 Sink Current vs Output Voltage Source Current vs Output Voltage 20203129 20203130 7 www.ti.com LM5100A/B/C, LM5101A/B/C Symbol LM5100A/B/C, LM5101A/B/C LM5100A/B/C IDD vs Frequency LM5101A/B/C IDD vs Frequency 20203110 20203109 Operating Current vs Temperature IHB vs Frequency 20203111 20203114 Quiescent Current vs Supply Voltage Quiescent Current vs Temperature 20203119 20203118 www.ti.com 8 Undervoltage Threshold Hysteresis vs Temperature 20203122 20203117 Bootstrap Diode Forward Voltage LM5100A/B/C Input Threshold vs Temperature 20203123 20203115 LM5101A/B/C Input Threshold vs Temperature LM5100A/B/C Input Threshold vs VDD 20203125 20203124 9 www.ti.com LM5100A/B/C, LM5101A/B/C Undervoltage Rising Thresholds vs Temperature LM5100A/B/C, LM5101A/B/C LM5101A/B/C Input Threshold vs VDD LM5100A/B/C Propagation Delay vs Temperature 20203126 20203112 LM5101A/B/C Propagation Delay vs Temperature LO & HO Gate Drive - High Level Output Voltage vs Temperature 20203113 20203120 LO & HO Gate Drive - Low Level Output Voltage vs Temperature LO & HO Gate Drive - Output High Voltage vs VDD 20203131 20203121 www.ti.com 10 LM5100A/B/C, LM5101A/B/C LO & HO Gate Drive - Output Low Voltage vs VDD 20203132 Timing Diagram 20203104 FIGURE 2. 11 www.ti.com LM5100A/B/C, LM5101A/B/C discharge the MOSFET gate into a minimal physical area. This will decrease the loop inductance and minimize noise issues on the gate terminal of the MOSFET. The MOSFETs should be placed as close as possible to the gate driver. b) The second high current path includes the bootstrap capacitor, the bootstrap diode, the local ground referenced bypass capacitor and low-side MOSFET body diode. The bootstrap capacitor is recharged on a cycle-by-cycle basis through the bootstrap diode from the ground referenced VDD bypass capacitor. The recharging occurs in a short time interval and involves high peak current. Minimizing this loop length and area on the circuit board is important to ensure reliable operation. A recommended layout pattern for the driver is shown in the following figure. If possible a single layer placement is preferred. Layout Considerations The optimum performance of high and low-side gate drivers cannot be achieved without taking due considerations during circuit board layout. Following points are emphasized. 1. Low ESR / ESL capacitors must be connected close to the IC, between VDD and VSS pins and between the HB and HS pins to support the high peak currents being drawn from VDD during turn-on of the external MOSFET. 2. To prevent large voltage transients at the drain of the top MOSFET, a low ESR electrolytic capacitor must be connected between MOSFET drain and ground (VSS). 3. In order to avoid large negative transients on the switch node (HS pin), the parasitic inductances in the source of top MOSFET and in the drain of the bottom MOSFET (synchronous rectifier) must be minimized. 4. Grounding Considerations: a) The first priority in designing grounding connections is to confine the high peak currents that charge and 20203138 www.ti.com 12 LM5100A/B/C, LM5101A/B/C Diode Power Dissipation VIN = 50V Power Dissipation Considerations The total IC power dissipation is the sum of the gate driver losses and the bootstrap diode losses. The gate driver losses are related to the switching frequency (f), output load capacitance on LO and HO (CL), and supply voltage (VDD) and can be roughly calculated as: PDGATES = 2 * f * CL * VDD2 There are some additional losses in the gate drivers due to the internal CMOS stages used to buffer the LO and HO outputs. The following plot shows the measured gate driver power dissipation versus frequency and load capacitance. At higher frequencies and load capacitance values, the power dissipation is dominated by the power losses driving the output loads and agrees well with the above equation. This plot can be used to approximate the power losses due to the gate drivers. 20203106 Gate Driver Power Dissipation (LO + HO) VDD = 12V, Neglecting Diode Losses 20203105 The bootstrap diode power loss is the sum of the forward bias power loss that occurs while charging the bootstrap capacitor and the reverse bias power loss that occurs during reverse recovery. Since each of these events happens once per cycle, the diode power loss is proportional to frequency. Larger capacitive loads require more energy to recharge the bootstrap capacitor resulting in more losses. Higher input voltages (VIN) to the half bridge result in higher reverse recovery losses. The following plot was generated based on calculations and lab measurements of the diode recovery time and current under several operating conditions. This can be useful for approximating the diode power dissipation. The total IC power dissipation can be estimated from the previous plots by summing the gate drive losses with the bootstrap diode losses for the intended application. 13 www.ti.com LM5100A/B/C, LM5101A/B/C Physical Dimensions inches (millimeters) unless otherwise noted Controlling dimension is inch. Values in [ ] are millimeters. Notes: Unless otherwise specified. 1. Standard lead finish to be 200 microinches/5.08 micrometers minimum lead/tin (solder) on copper. 2. 3. Dimension does not include mold flash. Reference JEDEC registration MS-012, Variation AA, dated May 1990. SOIC-8 Outline Drawing NS Package Number M08A PSOP-8 Outline Drawing NS Package Number MRA08A www.ti.com 14 LM5100A/B/C, LM5101A/B/C LLP-8 Outline Drawing NS Package Number SDC08A Notes: Unless otherwise specified. 1. For solder thickness and composition, see "Solder Information" in the packaging section of the National Semiconductor web page (www.national.com). 2. 3. Maximum allowable metal burr on lead tips at the package edges is 76 microns. No JEDEC registration as of May 2003. LLP-10 Outline Drawing NS Package Number SDC10A 15 www.ti.com LM5100A/B/C, LM5101A/B/C eMSOP-8 Outline Drawing NS Package Number MUY08A www.ti.com 16 www.ti.com 17 LM5100A/B/C, LM5101A/B/C Notes LM5100A/B/C, LM5101A/B/C 3A, 2A and 1A High Voltage High-Side and Low-Side Gate Drivers Notes www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated