CRCW...BC e3 www.vishay.com Vishay BCcomponents Lead (Pb)-free Thick Film, Rectangular Commodity Chip Resistors FEATURES * High volume product suitable for commercial applications * Excellent stability (R/R 1 % for 1000 h at 70 C) * Lead (Pb)-free solder contacts on Ni barrier layer * Metal glaze on high quality ceramic * Protective overglaze * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS MODEL CRCW0201...BC CRCW0402...BC CRCW0603...BC CRCW0805...BC CRCW1206...BC CRCW1210...BC CRCW2010...BC CRCW2512...BC CASE SIZE INCH 0201 0402 0603 0805 1206 1210 2010 2512 CASE SIZE METRIC RR 0603M RR 1005M RR 1608M RR 2012M RR 3216M RR 3225M RR 5025M RR 6332M POWER RATING P70 C W LIMITING ELEMENT VOLTAGE MAX. V TEMPERATURE COEFFICIENT ppm/K TOLERANCE % 200 0.5 - 200/+ 400 100 0.05 30 200 1 - 200/+ 400 200 5 - 200/+ 400 Zero-Ohm-Resistor: Rmax. = 50 m, Imax. at 70 C = 1.0 A 100 1 0.063 50 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 1.5 A 100 1 0.10 75 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 2.0 A 100 1 0.125 150 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 2.5 A 100 1 200 0.25 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 3.5 A 100 1 0.50 200 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 4.0 A 100 1 0.75 400 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 5.0 A 100 1 1.0 500 200 200 5 Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 C = 7.0 A RESISTANCE RANGE 10R to 10M 1R0 to 9R76 47R to 10M 10R to 10M 1R0 to 9R76 10R to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 10M 1R0 to 9R76 1R0 to 10M 1R0 to 10M 1R0 to 9R76 1R0 to 10M E-SERIES E96 E24; E96 E24 E24; E96 E24 E24; E96 E24 E24; E96 E24 E24; E96 E24 E24; E96 E24 E24; E96 E24 E24; E96 E24 Notes * These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. * Power rating depends on the maximum temperature at the solder point, the component placement density and the substrate material Revision: 30-Jan-13 Document Number: 28743 1 For technical questions, contact: f3aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRCW...BC e3 www.vishay.com Vishay BCcomponents TECHNICAL SPECIFICATIONS PARAMETER UNIT CRCW0201...BC CRCW0402...BC CRCW0603...BC CRCW0805...BC CRCW1206...BC CRCW1210...BC CRCW2010...BC CRCW2512...BC Rated Dissipation at 70 C (1) W 0.050 0.063 0.10 0.125 0.25 0.50 0.75 1.0 Limiting Element Voltage Umax. AC/DC V 30 50 75 150 200 200 400 500 Insulation Voltage Uins (1 min) V 50 75 100 200 300 300 300 300 Insulation Resistance > 109 Operating Temperature Range C - 55 to + 155 Failure Rate C 0.3 x 10-9 Weight/ 1000 Pieces g 16 25.5 40.5 0.17 0.65 2 5.5 10 Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 C is not exceeded. PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRCW0603562RFKTCBC C R C W 0 6 0 3 5 6 2 R F K T C B C MODEL VALUE TOLERANCE TCR PACKAGING Special CRCW0201 CRCW0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW2010 CRCW2512 R = Decimal K = Thousand M = Million 0000 = Jumper D = 0.5 % F = 1.0 % J = 5.0 % Z = Jumper K = 100 ppm/K N = 200 ppm/K X = - 200 ppm/K/ + 400 ppm/K 0 = Jumper TA, TB TC, TD TE, TF TH, TI Up to 2 digits BC = Commodity PRODUCT DESCRIPTION: CRCW0603-BC 100 562R 1 % RT6 e3 CRCW0603-BC 100 562R 1% RT6 e3 MODEL TCR RESISTANCE VALUE TOLERANCE VALUE PACKAGING LEAD (Pb)-FREE CRCW0201-BC CRCW0402-BC CRCW0603-BC CRCW0805-BC CRCW1206-BC CRCW1210-BC CRCW2010-BC CRCW2512-BC 100 ppm/K 200 ppm/K - 200 ppm/K/ + 400 ppm/K 10R = 10 562R = 562 10K = 10.0 k 1M = 1 M 0R0 = Jumper 0.5 % 1% 5% RT1, RT2 RT5, RT6 RT7, RF4 R02, R82 e3 = Pure tin termination finish Revision: 30-Jan-13 Document Number: 28743 2 For technical questions, contact: f3aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRCW...BC e3 www.vishay.com Vishay BCcomponents PACKAGING REEL PACKAGING CODE MODEL TAPE WIDTH CRCW0201...BC 8 mm CRCW0402...BC 8 mm CRCW0603...BC 8 mm CRCW0805...BC 8 mm CRCW1206...BC 8 mm CRCW1210...BC 8 mm CRCW2010...BC CRCW2512...BC 12 mm 12 mm DIAMETER PITCH 180 mm/7" 254 mm/10" 330 mm/13" 180 mm/7" 254 mm/10" 330 mm/13" 180 mm/7" 254 mm/10" 330 mm/13" 180 mm/7" 254 mm/10" 330 mm/13" 180 mm/7" 254 mm/10" 330 mm/13" 180 mm/7" 254 mm/10" 330 mm/13" 180 mm/7" 180 mm/7" PIECES/ REEL PART NUMBER BLISTER PAPER BLISTER TD TI TE TD TI TE TA TB TC TA TB TC TA TB TC TA TB TC - TF TH RT7 RT2 RF4 RT7 RT2 RF4 RT1 RT5 RT6 RT1 RT5 RT6 RT1 RT5 RT6 RT1 RT5 RT6 - R02 R82 10 000 20 000 50 000 10 000 20 000 50 000 5000 10 000 20 000 5000 10 000 20 000 5000 10 000 20 000 5000 10 000 20 000 4000 4000 2 mm 2 mm 4 mm 4 mm 4 mm 4 mm 4 mm 4 mm PRODUCT DESC. PAPER DIMENSIONS in millimeters SIZE SOLDER PAD DIMENSIONS (1) DIMENSIONS INCH METRIC L W REFLOW SOLDERING H T1 T2 0201 0603 0.6 0.05 0.3 0.05 0.23 0.05 0.15 0.05 0.2 0402 1005 1.0 0.05 + 0.05 - 0.10 WAVE SOLDERING a b l a b l 0.3 0.43 0.2 - - - 0.5 0.05 0.35 0.05 0.25 0.05 0.2 0.1 0.4 0.6 0.5 - - - 0.85 0.1 0.45 0.05 0.3 0.2 0.3 0.2 0.5 0.9 1.0 0.9 0.9 1.0 0.3 0.2 0.7 1.3 1.2 0.9 1.3 1.3 0.4 0.2 0.9 1.7 2.0 1.1 1.7 2.3 0603 1608 1.55 + 0.10 - 0.05 0805 2012 2.0 + 0.20 - 0.10 1.25 0.15 0.45 0.05 0.3 1206 3216 3.2 + 0.10 - 0.20 1.6 0.15 0.55 0.05 0.45 0.2 1210 3225 3.2 0.2 2.5 0.2 0.55 0.05 0.45 0.2 0.4 0.2 0.9 2.5 2.0 1.1 2.5 2.2 2010 5025 5.0 0.15 2.5 0.15 0.6 0.1 0.6 0.2 0.6 0.2 1.0 2.5 3.9 1.2 2.5 3.9 2512 6332 6.3 0.2 3.15 0.15 0.6 0.1 0.6 0.2 0.6 0.2 1.0 3.2 5.2 1.2 3.2 5.2 + 0.20 - 0.10 Note (1) The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of power dissipation may raise the temperature of the solder joint, hence special solder alloys or boardmaterials maybe required to maintain the reliability of the assembly. Specified power rating above 125 C requires dedicated heat-sink pads, which depend on boardmaterials. The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many other parameters. Still the given solder pad dimensions will be found adequate for most general applications. (2) No marking for 0201 and 0402 sizes. Revision: 30-Jan-13 Document Number: 28743 3 For technical questions, contact: f3aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRCW...BC e3 www.vishay.com Vishay BCcomponents Rated Power in % DERATING 120 100 80 60 40 20 0 - 55 - 25 0 25 50 75 70 100 125 155 175 Ambient Temperature in C TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD REQUIREMENTS PERMISSIBLE CHANGE (R) TEST PROCEDURE STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER SIZE 0201 1 to 10 M 1 to 10 M 1 to 10 M Stability for product types: CRCW....BC e3 4.5 - Resistance - 1% 5% 0.5 %, 1 %, 5 % 4.8.4.2 - Temperature coefficient (20/- 55/20) C and (20/125/20) C 100 ppm/K, 200 ppm/K 200 ppm/K 100 ppm/K, 200 ppm/K, - 200 ppm/K/ + 400 ppm/K 4.13 - Short time overload U = 2.5 x P 70 x R 2 x Umax.; duration: Acc. to the style 4.17.5 4.18.2 4.19 4.24 58 (Td) Solderability 58 (Td) Resistance to soldering heat 14 (Na) Rapid change of temperature 78 (Cab) Revision: 30-Jan-13 Damp heat, steady state Pre-aging 4 h at 155 C, dryheat (0.25 % R + 0.05 ) (0.5 % R + 0.05 ) (1 % R + 0.05 ) Solder bath method; Sn60Pb40 non activated flux; (235 5) C (2 0.2) s Good tinning ( 95 % covered) no visible damage Solder bath method; Sn96.5Ag3Cu0.5 non activated flux; (245 5) C (3 0.3) s Good tinning ( 95 % covered) no visible damage Solder bath method (260 5) C; (10 1) s 30 min. at - 55 C; 30 min. at 125 C; 5 cycles (0.25 % R + 0.05 ) (0.5 % R + 0.05 ) (1 % R + 0.05 ) (0.25 % R + 0.05 ) (0.5 % R + 0.05 ) (0.5 % R + 0.05 ) 1000 cycles (1 % R + 0.05 ) (1 % R + 0.05 ) (1 % R + 0.05 ) (40 2) C; 56 days; (93 3) % RH (1 % R + 0.05 ) (2 % R + 0.1 ) (2 % R + 0.1 ) Document Number: 28743 4 For technical questions, contact: f3aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRCW...BC e3 www.vishay.com Vishay BCcomponents TEST PROCEDURES AND REQUIREMENTS IEC EN 60115-1 60068-2 CLAUSE TEST METHOD REQUIREMENTS PERMISSIBLE CHANGE (R) TEST STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER SIZE 0201 1 to 10 M 1 to 10 M 1 to 10 M (1 % R + 0.05 ) (2 % R + 0.1 ) (2 % R + 0.1 ) 70 C; 1000 h (1 % R + 0.05 ) (2 % R + 0.1 ) (2 % R + 0.1 ) 70 C; 8000 h (2 % R + 0.1 ) (4 % R + 0.1 ) (4 % R + 0.1 ) 125 C, 1000 h (1 % R + 0.05 ) (2 % R + 0.1 ) (2 % R + 0.1 ) PROCEDURE Stability for product types: CRCW....BC e3 - Climatic sequence: - 4.23.2 2 (Ba) Dry heat 125 C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 C; 90 % RH; 24 h; 1 cycle 4.23.4 1 (Aa) Cold - 55 C; 2 h 4.23.5 13 (M) Low air pressure 1 kPa; (25 10) C; 1 h 4.23.6 30 (Db) Damp heat, cyclic 55 C; 90 % RH; 24 h; 5 cycles 4.23.7 - DC load 4.23 U= P 70 x R Umax. U = P 70 x R Umax.; 1.5 h on; 0.5 h off; 4.25.1 4.25.3 - - Endurance at 70 C Endurance at 125 C APPLICABLE SPECIFICATIONS * EN60115-1Generic specification * IEC 60068-2-XVariety of environmental test procedures * EN140400Sectional specification * IEC 60286-3Packaging of SMD components * EN140401-802Detail specification Revision: 30-Jan-13 Document Number: 28743 5 For technical questions, contact: f3aresistors@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000