LD39015Jxx 150 mA low quiescent current low noise voltage regulator Features Input voltage from 1.5 to 5.5 V Ultra low dropout voltage (90 mV typ. at 100 mA load) Very low quiescent current (20 A typ. at no load, 35 A typ. at 150 mA load, 1 A max in off mode) Low noise (54 VRMS from 10 Hz to 100 kHz at VOUT = 1.8 V) Output voltage tolerance: 2.0% @ 25 C 150 mA guaranteed output current Wide range of output voltages available on request: 0.8 V to 4.5 V with 100 mV step Logic-controlled electronic shutdown Compatible with ceramic capacitor COUT = 1 F Internal current and thermal limit Flip-chip 4 bumps 1.1 x 1.1 mm. Temperature range: -40 C to 125 C Flip-chip 4 74 dB at low frequencies and starts to roll off at 10 kHz. Enable logic control function puts the LD39015Jxx in shut-down mode allowing a total current consumption lower than 1 A. The device also includes a short-circuit constant current limiting and thermal protection. Typical applications are mobile phones, personal digital assistant (PDAs), cordless phone and similar battery powered systems. Description The LD39015Jxx provides 150 mA maximum current from an input voltage ranging from 1.5 V to 5.5 V with a typical dropout voltage of 80 mV. It is stable with ceramic capacitor. The ultra low drop-voltage, low quiescent current and low noise features make it suitable for low power battery powered applications. Power supply rejection is Table 1. August 2009 Device summary Part numbers Order codes Output voltages LD39015JXX12 LD39015J12R 1.2 V LD39015JXX13 LD39015JJ13R 1.3 V LD39015JXX15 LD39015J15R 1.5 V LD39015JXX18 LD39015J18R 1.8 V LD39015JXX28 LD39015J28R 2.8 V Doc ID 15968 Rev 2 1/17 www.st.com 17 Contents LD39015Jxx Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 Different output voltage versions of the LD39015Jxx available on request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 Doc ID 15968 Rev 2 LD39015Jxx Diagram 1 Diagram Figure 1. Block diagram OUT IN BandGap 1.22 V R1 Trimming Thermal Protection R2 Enable EN GND Doc ID 15968 Rev 2 3/17 Pin configuration LD39015Jxx 2 Pin configuration Figure 2. Pin connection (top view) Table 2. Pin description 4/17 Pin n Symbol A2 EN A1 GND B2 IN B1 OUT Function Enable pin logic input: Low=shutdown, High=active Common ground Input voltage of the LDO Output voltage Doc ID 15968 Rev 2 LD39015Jxx Typical application 3 Typical application Figure 3. Typical application circuit VIN IN 1 F VEN VOUT OUT 1 F EN Load GND Doc ID 15968 Rev 2 5/17 Maximum ratings LD39015Jxx 4 Maximum ratings Table 3. Absolute maximum ratings Symbol VIN Parameter DC input voltage Value Unit - 0.3 to 6 V VOUT DC output voltage - 0.3 to VI + 0.3 V VEN Enable input voltage - 0.3 to VI + 0.3 V IOUT Output current Internally limited mA Power dissipation Internally limited mW PD TSTG Storage temperature range -65 to 150 C TOP Operating junction temperature range -40 to 125 C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. All values are referred to GND. Table 4. Thermal data Symbol RthJA 6/17 Parameter Thermal resistance junction-ambient Doc ID 15968 Rev 2 Value Unit 180 C/W LD39015Jxx 5 Electrical characteristics Electrical characteristics TJ = 25 C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 F, IOUT = 1 mA, VEN = VIN, unless otherwise specified. Table 5. Symbol VIN Electrical characteristics Parameter Test conditions Operating input voltage Min. 1.5 Turn-on threshold VUVLO VOUT 1.45 Turn-off threshold VOUT accuracy Typ. 1.30 Max. Unit 5.5 V 1.48 V 1.35 mV VOUT > 1.5V, IOUT = 1mA, TJ = 25C -2.0 2.0 VOUT > 1.5V, IOUT = 1mA, -40C < TJ < 125C -3.0 3.0 % VOUT 1.5V, IOUT = 1mA 10 VOUT 1.5V, IOUT = 1mA, -40C < TJ < 125C 30 mV VOUT Static line regulation VOUT +1V VIN 5.5V, IOUT = 1mA 0.01 %/V VOUT Static load regulation IOUT = 1mA to 150mA 0.002 %/mA VDROP Dropout voltage (1) IOUT = 100mA, VOUT > 1.5V -40C < TJ < 125C 90 Output noise voltage 10Hz to 100kHz, IOUT = 10mA, VOUT = 1.8V, VIN = 2.8V 54 VIN = VOUTNOM + 1V +/-VRIPPLE VRIPPLE = 0.1V, freq. = 1kHz IOUT = 10mA 74 VIN = VOUTNOM + 0.5V +/-VRIPPLE VRIPPLE = 0.1V, Freq.=10kHz IOUT = 10mA 67 IOUT = 0mA 20 eN SVR Supply voltage rejection VOUT = 1.5V 35 A IOUT = 0 to 150mA -40C < TJ< 125C 50 VIN input current in OFF MODE: VEN = GND Short circuit current RL = 0 Enable input logic low VIN = 1.5V to 5.5V, -40C < TJ < 125C Enable input logic high VIN = 1.5V to 5.5V, -40C < TJ < 125C IEN Enable pin input current VSHDN = VIN, -40C < TJ < 125C TON Turn on time (2) ISC VEN 0.003 1 200 mA 0.4 0.9 V V 0.1 30 Doc ID 15968 Rev 2 VRMS 40 IOUT = 0 to 150mA Quiescent current mV dB IOUT = 0mA, -40C < TJ < 125C IQ 130 1 A s 7/17 Electrical characteristics Table 5. Symbol TSHDN COUT LD39015Jxx Electrical characteristics (continued) Parameter Test conditions Min. Typ. Thermal shutdown 160 Hysteresis 20 Max. Unit C Output capacitor Capacitance (see typical performance characteristics for stability) 1 22 F 1. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This specification does not apply for output voltages below 1.5 V. 2. Turn-on time is time measured between the enable input just exceeding VEN High Value and the output voltage just reaching 95% of its nominal value. 8/17 Doc ID 15968 Rev 2 LD39015Jxx Typical performance characteristics 6 Typical performance characteristics Figure 4. Output voltage vs. temperature Figure 5. 1.24 Output voltage vs. input voltage 2 1.23 1.8 1.22 1 mA 1.6 150 mA 1.2 VOUT [V] VOUT [V] 1.21 1.19 1.18 1.4 1.2 1.17 1 1.16 0.8 1.15 0.6 1.14 -75 -50 -25 0 25 50 0 75 100 125 150 175 0.5 1 1.5 2.5 3 3.5 4 4.5 5 5.5 6 VIN [V] T [C] Figure 6. 2 Dropout voltage vs. output current Figure 7. COUT stability region ESR @ 100KHz [W] 3 CI = 1 F, VIN = VEN = VOUTNOM +1 to 5.5 V 2.5 IOUT=1 to 150mA 2 1.5 1 STABLE ZONE 0.5 0 0 5 10 15 20 COUT [F] (nominal value) Supply voltage rejection vs. frequency Figure 9. Output noise spectral density Noise spectrum - VOUT(NOM) = 1.2V VIN=2.2V 1.4E-05 1.2E-05 IOUT = 0A 1.0E-05 Vnoise [V] Figure 8. IOUT = 1mA IOUT = 10mA 8.0E-06 IOUT = 100mA 6.0E-06 4.0E-06 2.0E-06 0.0E+00 10 100 1000 10000 100000 f [Hz] Doc ID 15968 Rev 2 9/17 Typical performance characteristics LD39015Jxx Figure 10. SVR vs. drop 90 Figure 11. Quiescent current vs. IOUT IQ versus IOUT IOUT = 10 mA, VOUT = 1.8 V, VIN = 0.3 V, f = 1kHz 40 85 35 30 IQ(GND) [uA] dB 80 75 70 25 20 15 10 65 5 60 0 0 0.5 1 1.5 2 2.5 3 3.5 4 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 IOUT [mA] VDROP(VIN - VOUT) Figure 12. Quiescent current vs. input voltage Figure 13. Load transient IQ(GND) versus VIN ILOAD = 1mA 35 ILOAD = 0 IQ(GND) [uA] 30 25 20 15 10 5 0 0 1 2 3 4 5 6 7 VIN [V] IOUT = 10mA to 150mA, tr = tf = 5s Figure 14. Line transient Figure 15. Enable transient IOUT = 10 mA; VOUT= 1.8 V; VIN = 0.5 V; VIN = from 2.550 to 3.055V; Tr = Tf = 5 s VIN = 1.5 V, VEN = 0 to 1 V, IOUT = 1 mA, CIN = COUT = 1 F 10/17 Doc ID 15968 Rev 2 LD39015Jxx 7 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Doc ID 15968 Rev 2 11/17 Package mechanical data LD39015Jxx Flip-chip 4 mechanical data mm. mils. Dim. Min. Typ. Max. Min. Typ. Max. A 0.585 0.65 0.715 23.03 25.59 28.15 A1 0.21 0.25 0.29 8.27 9.84 11.42 A2 0.40 15.75 b 0.265 0.315 0.365 10.43 12.40 14.37 D 1.02 1.07 1.12 40.15 42.13 44.09 D1 E 0.5 1.02 1.07 19.69 1.12 40.15 42.13 E1 0.5 19.69 SD 0.25 9.84 SE 0.25 9.84 44.09 7224716/G 12/17 Doc ID 15968 Rev 2 LD39015Jxx Package mechanical data Tape and reel Flip-chip 4 mechanical data mm. inch. Dim. Min. Typ. A Max. Min. Typ. 178 C 12.8 D 20.2 N 59 13.2 Max. 6.926 0.504 0.519 0.795 60 T 61 2.323 2.362 8.4 2.401 0.331 Ao 1.12 1.17 1.22 0.044 0.046 0.048 Bo 1.12 1.17 1.22 0.044 0.046 0.048 Ko 0.68 0.73 0.78 0.027 0.029 0.031 Po 3.9 4 4.1 0.153 0.157 0.161 P 3.9 4 4.1 0.153 0.157 0.161 Doc ID 15968 Rev 2 13/17 Package mechanical data LD39015Jxx Figure 16. Foot print data 14/17 Doc ID 15968 Rev 2 LD39015Jxx Different output voltage versions of the LD39015Jxx available on request 8 Different output voltage versions of the LD39015Jxx available on request Table 6. Options available on request Order codes Output voltages LD39015J08R 0.8 V LD39015J10R 1.0 V LD39015J33R 3.3 V Doc ID 15968 Rev 2 15/17 Revision history LD39015Jxx 9 Revision history Table 7. Document revision history Date Revision 29-Jun-2009 1 First release. 05-Aug-2009 2 Updated tape and reel mechanical data on page 13. 16/17 Changes Doc ID 15968 Rev 2 LD39015Jxx Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 15968 Rev 2 17/17