Product Data Sheet Industrial USB Flash Drive Module U-110 Series USB2.0 high speed B U: Fl a sh Pr od u ct s Date : Ju ne 0 3 , 20 1 4 Re vi si o n: 1 .6 0 Fi le : U - 1 10 _da ta_ s he e t_ UI - x x BP_ Re v 16 0 .d oc U-110 Series USB Flash Drive Module 1GByte to 16GByte USB Flash Drive Module provides non-volatile, solid-state storage in a compact design, making it perfectly suited for embedded applications. The standard USB 2.0 interface provides designers with a true plug-n-play storage device, allowing for short design cycles and fast time to market. Swissbit use high end USB 2.0 flash memory controller in the Module, providing high data reliability and endurance. The built-in BCH-ECC engine can detect up to 9-bit errors and correct up to 8-bit errors, while sophisticated wear leveling algorithms guarantee up to 2,000,000 Write Cycles. The internal USB Flash Drive Module has an internal 9(10) pin USB connector. High performance, high reliability and low cost per megabyte make the internal USB Flash Drive Module the product of choice in embedded applications, such as Gaming, POS Workstations, Networking Equipment and Industrial PCs. Swissbit offers value-added services to OEM customers, such as controlled Bill of Materials, customized preloads, custom setting, customer-specific marking etc. 1 Feature summary USB2.0 solid state flash Drive for internal 9(10)-pin USB connector o Fully compliant with USB-Specification 2.0 (High-Speed, 480Mb/s burst) o Fully backward compliant with USB 1.1 systems (Full speed, 12Mb/s burst) High reliability o Error correction code (ECC) o Wear leveling o MTBF >3,000,000 hours o Data reliability: < 1 non-recoverable error per 1014 bits read Commercial and industrial temperature grade Plug & Play Standard operating voltage 5V, 3.3V optional Bootable Fixed drive LED indicator FAT32 format Unique serial number USB-IF high speed certified CE / FCC RoHS compliant WEEE Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 2 of 17 Table of Content 1 FEATURE SUMMARY .....................................................................................................................................................2 TABLE OF CONTENT .........................................................................................................................................................3 2 ORDER INFORMATION..................................................................................................................................................4 2.1 STANDARD PRODUCTS WITH 2.54MM (J) CONNECTOR FOR 5V (STD) .................................................................................4 2.2 LOW PROFILE PRODUCTS WITH 2.00MM (K) CONNECTOR FOR 5V (STD) ............................................................................4 2.3 STANDARD PRODUCTS WITH 2.54MM (J) CONNECTOR FOR 3.3V (3V3)..............................................................................4 2.4 LOW PROFILE PRODUCTS WITH 2.00MM (K) CONNECTOR FOR 3.3V (3V3).........................................................................4 2.5 OFFERED OPTIONS FOR CUSTOM PRODUCTS ...................................................................................................................4 3 SYSTEM PERFORMANCE ...............................................................................................................................................5 4 INTERFACE / PIN OUT ..................................................................................................................................................5 5 NAND FLASH TECHNOLOGIES ......................................................................................................................................5 6 ELECTRICAL SPECIFICATION .........................................................................................................................................6 7 ENVIRONMENTAL SPECIFICATION AND RELIABILITY ....................................................................................................7 7.1 RECOMMENDED OPERATING CONDITIONS ......................................................................................................................7 7.2 RELIABILITY ...........................................................................................................................................................7 7.3 SHOCK, VIBRATION, AND HUMIDITY ...........................................................................................................................7 8 COMPATIBILITY & COMPLIANCE ..................................................................................................................................7 9 APPLICATIONS ............................................................................................................................................................. 8 10 PERFORMANCE REFERENCE .......................................................................................................................................8 10.1 TEST EQUIPMENT...................................................................................................................................................8 10.2 PERFORMANCE RESULTS .........................................................................................................................................8 11 STANDARD FORM FACTORS AND HARDWARE .............................................................................................................9 12 ROHS AND WEEE UPDATE FROM SWISSBIT .............................................................................................................. 12 13 BEST PRACTICES........................................................................................................................................................ 14 13.1 WEAR LEVELING AND SPARE BLOCK MANAGEMENT .................................................................................................... 14 13.1 DEVICE REMOVAL & POWER FAILURE ...................................................................................................................... 14 13.2 LIFETIME END HANDLING ...................................................................................................................................... 14 14 PART NUMBER DECODER ......................................................................................................................................... 15 15 LABEL ....................................................................................................................................................................... 16 16 REVISION HISTORY ................................................................................................................................................... 17 Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 3 of 17 2 Order Information 2.1 Standard products with 2.54mm (J) connector for 5V (STD) Density Part Number 1GB SFUI1024J3BP2TO-t-MS-221-STD 2GB SFUI2048J3BP2TO-t-MS-221-STD 4GB SFUI4096J3BP2TO-t-DT-221-STD 8GB SFUI8192J3BP2TO-t-QT-221-STD 16GB SFUI16GBJ1BP2MT-t-QT-231-STD Table 1: Product List - 2.54mm, 5V 2.2 Low profile products with 2.00mm (K) connector for 5V (STD) Density Part Number 1GB SFUI1024K3BP2TO-t-MS-221-STD 2GB SFUI2048K3BP2TO-t-MS-221-STD 4GB SFUI4096K3BP2TO-t-DT-221-STD 8GB SFUI8192K3BP2TO-t-QT-221-STD 16GB SFUI16GBK1BP2MT-t-QT-231-STD Table 2: Product List -2.00mm, 5V 2.3 Standard products with 2.54mm (J) connector for 3.3V (3V3) Density Part Number 1GB SFUI1024J3BP2TO-t-MS-221-3V3 2GB SFUI2048J3BP2TO-t-MS-221-3V3 4GB SFUI4096J3BP2TO-t-DT-221-3V3 8GB SFUI8192J3BP2TO-t-QT-221-3V3 16GB SFUI16GBJ1BP2MT-t-QT-231-3V3 Table 3: Product List - 2.54mm, 3.3V The maximum supply voltage for 3.3V types must not exceed 3.6V! 2.4 Low profile products with 2.00mm (K) connector for 3.3V (3V3) Density Part Number 1GB SFUI1024K3BP2TO-t-MS-221-3V3 2GB SFUI2048K3BP2TO-t-MS-221-3V3 4GB SFUI4096K3BP2TO-t-DT-221-3V3 8GB SFUI8192K3BP2TO-t-QT-221-3V3 16GB SFUI16GBK1BP2MT-t-QT-231-3V3 Table 4: Product List -2.00mm, 3.3V The maximum supply voltage for 3.3V types must not exceed 3.6V! t = temperature grade (C=0C to 70C and I=-40C to +85C) 2.5 Offered options for custom products Removable or fixed drive Customer specified strings and IDs FAT16, FAT32 format or customer file system, default FAT32 Preload service CD partition Auto run option Dongle functionality Extended and Industrial Temperature range Please ask our sales for more details and additional features. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 4 of 17 3 System performance Speed High Speed mode (max) Full Speed mode (max) unit Burst Read Write 480 32 1) 23 1) 12 1.0 0.9 Mbit/s 1) MByte/s Effective speed varies with controller, number and type of flash, host, file size, file system and operating system The USB drive can be busy for max. 320ms from time to time due to internal reorganization. 4 Interface / Pin out USB-connector 10pin (2mm or 2.54mm pitch) USB 2.0 high speed interface, USB1.1 full speed compatible STD variation Pin Signal 1 2 3 4 5 6 7 8 V_Bus NC DNC D+ NC GND NC Comment Operating voltage Not Connected Data signal pair Not Connected Data signal pair Not Connected Ground Not Connected Keyed at the 2.54mm connector 9 NC Keyed at the 2.00mm connector (optional not keyed) should be connected with host shield, 10 Shield is connected with card ground for standard products, could be configured as NC on request See also chapter 11 (Standard form factors and hardware) 5 NAND Flash technologies SLC and MLC flash o Single-level-cell (SLC) flash, 1 bit (1 level) is stored in each memory cell o Multi-level-cell (MLC) flash, 2 bit (3 level) are stored in each memory cell Differences SLC ~100,000 fast write MLC1) ~5,000 slow write Endurance Write Performance Read fast read fast read Performance Reliability high normal Price expensive cheap 1) Not recommended for OEM market or industrial applications Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland comment physical write/erase cycles MLC write is more time consuming because of 4 states MLC and SLC technology is similar in the read performance errors are more likely, because the 4 states the same density can be stored in less silicon Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 5 of 17 6 Electrical Specification Absolute Maximum Ratings Parameter Symbol Min Max Power Supply Voltage (5V Type) Power Supply Voltage (3.3V Type) Voltage on D+ and DCommercial Operating Temperature Extended Operating Temperature Industrial Operating Temperature V_Bus V_Bus V_Data -0.5 -0.5 -0.5 0 -25 -40 6.0 3.6 3.6 70 85 85 T_A Unit V C DC characteristics for Full-Speed operation (T=25C, V_Bus=5V or 3.3V) Parameter Symbol Test condition Min Typ Supply Voltage (5V Type) V_Bus 4.75*) 5.00 Supply Voltage (3.3V Type) V_Bus 3.13 3.3 Operating current I_CC 60 90 V_Bus=5.0V Suspend current I_CCS 350 Input LOW Voltage V_IL Input HIGH Voltage V_IH 2 RL of 1.5k to 3.6V Output LOW Voltage V_OL RL of 15k to GND Output HIGH Voltage V_OH 2.8 Output Signal Crossover V_CRS 1.3 Voltage *) The minimum operation voltage of the 5V drives is lower than the USB standard. It flash chips (see Minimum supply voltage table below) . Max Unit 5.25 3.6 120 500 0.8 V V mA A 0.3 3.6 2.0 V depends on the # of used DC characteristics for High-Speed operation (T=25C, V_Bus=5V or 3.3V) Parameter Symbol Supply Voltage (Standard) Supply Voltage (3.3V Type) Operating current Suspend current High Speed Idle Level High Speed Data Signaling LOW High Speed Data Signaling HIGH Chirp J Level (differential) Chirp K Level (differential) V_Bus V_Bus I_CC I_CCS V_HSOI V_HSOL Test condition V_Bus=5.0V V_HSOH Min Typ Max Unit 4.75*) 3.13 60 5.00 3.3 100 350 V V mA A -10 -10 5.25 3.6 180 500 10 10 360 440 mV V_CHIRPJ 360 440 V_CHIRP -440 -360 K *) The minimum operation voltage of the 5V drives is lower than the USB standard. It depends on the # of used flash chips (see Minimum supply voltage table below) . minimum supply voltage for 5V types Density Part Number min operation voltage SFUI1024c3BP2TO-t-MS-221-STD 1GB 3.25V SFUI2048c3BP2TO-t-MS-221-STD 2GB 3.25V SFUI4096c3BP2TO-t-DT-221-STD 4GB 3.55V SFUI8192c3BP2TO-t-QT-221-STD 8GB 3.55V SFUI16GBc1BP2MT-t-QT-231-STD 16GB 3.80V The minimum operation voltage must be guaranteed at the device connector. For 3.3V supply please use 3.3V types (part number suffix -3V3) (maximum 3.6V supply) Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 6 of 17 7 Environmental Specification and Reliability 7.1 Recommended operating conditions Parameter Symbol Commercial Operating Temperature Extended Operating Temperature Industrial Operating Temperature Storage Temperature T_A T_S Min 0 -25 -40 -50 Typ Max Unit 25 70 85 85 100 C 7.2 Reliability Parameter Value ~2'000'000 cycles1) 1 in 1014 bits, read BCH detect up to 9-bit errors / correct up to 8-bit errors per sector > 3,000,000 hours 10 years @ 10% life time / 1 years @ life end > 1500 insertions / removals Endurance (SLC NAND Flash) Data reliability Error correction code (ECC) MTBF / MTTF Data retention Durability 1) 100'000 program/erase cycles NAND Flash cell endurance / average file size written = 5% of device density (50MB for 1GB device)/no static data 7.3 Shock, Vibration, and Humidity Parameter Value 1500G Peak, 0.5m pulse duration, 5 pulses, 6 axes (JESD22-B110) 20G Peak, 20-2000 Hz, 4 cycles per direction (X, Y and Z) (JESD22-B103) 85C, 85% RH, Vmax for 500 hrs (JESD22-A101) Shock Vibration Humidity 8 Compatibility & Compliance Configurable as boot-drive Standard fix Configuration (mounted as local drive, not as removable drive) Operating Systems: o Windows CE o Windows Server 2003 and 2008 o Windows 7, Vista, XP, 2000, ME o Win98 SE (driver available) o Mac 9.0 and newer o Mac 8.6 (with driver) and newer o Linux 2.4 and newer o All USB mass-storage host systems (guarantee on all USB-IF certified systems) CE - EN 55022/55024 FCC class B for information technology USB-IF high speed certified RoHS UL60950 compliant PCB WEEE Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 7 of 17 9 Applications Gaming Industrial PCs Point-Of-Sale (POS) Industrial Automation Networking Equipment Medical Equipment Data Recorders 10 Performance reference 10.1 Test Equipment Mainboard: OS: Firmware: Filesystem: ASUS P5LD2 Win XP Prof. V.2002 SP3 Depends on generation Low level CPU: Testsoftware: Prod.Tool: Intel Core 2 4400 @2.0GHz Swissbit FlashTest 1.2.1/1.3.0 / Script Performance" SPT 1.0.22/23 SDK: 1.0.24 10.2 Performance results The effective speed depends on Controller, Number and type of flash, File system and file size, Test tool & OS. Cards with the low-profile connector (Partnumber ... K1BP...) have the same properties. SFUI1024J*BP2TO-t-MS* SFUI2048J*BP2TO-t-MS* SFUI4096J*BP2TO-t-DT* SFUI8192J*BP2TO-t-QT* SFUI16GBJ*BP2MT-t-QT* SFUI1024J*BP2TO-t-MS* SFUI2048J*BP2TO-t-MS* SFUI4096J*BP2TO-t-DT* SFUI8192J*BP2TO-t-QT* SFUI16GBJ*BP2MT-t-QT* Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Random Read [kByte/sec] 8 sector - 4kByte 128 sector 64kByte ~5800 ~24800 ~5800 ~26500 ~5800 ~26000 ~5400 ~25900 ~5100 ~26000 Random Write [kByte/sec] 8 sector - 4kByte 128 sector 64kByte ~100 ~1600 ~75 ~1200 ~75 ~1150 ~75 ~1150 ~22 ~390 Sequential Read [kByte/sec] 8 sector - 4kByte 128 sector 64kByte ~7800 ~26200 ~8100 ~28500 ~8100 ~28700 ~8000 ~28900 ~6600 ~2700 Sequential Write [kByte/sec] 8 sector - 4kByte 128 sector 64kByte ~6500 ~8100 ~4600 ~11800 ~4600 ~20800 ~4600 ~20800 ~2900 ~22000 Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 8 of 17 11 Standard form factors and hardware Standard form factor of PCBs 36.8mm x 26.65mm Hole for mechanical fixture (optional grounded) Shield (connector Pin 10) grounded (optional NC) 2 additional holes LED for operation indication (optional no LED) 2 connector types o 2.54mm pitch, 7.5mm long standard o 2.00mm pitch, 3.6mm long low profile Component heights max. 1.6mm on connector side max. 1.2mm on flash side Figure 1: Mechanical Dimensions for 2.54mm connector (standard) Figure 2: Mechanical Dimensions for 2.54mm connector (standard) Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 9 of 17 Figure 3: Mechanical Dimensions for 2.00mm connector (low profile) Figure 4: Mechanical Dimensions for 2.00mm connector (low profile) Variations Part number Connector Power Supply Pin 9 SFUIxxxxJgBP2xx-t-xx-2f1-STD 2.54 mm 5V Key pin SFUIxxxxKgBP2xx-t-xx-2f1-STD 2.00 mm 5V Key pin SFUIxxxxJgBP2xx-t-xx-2f1-3V3 2.54 mm 3.3V Key pin SFUIxxxxKgBP2xx-t-xx-2f1-3V3 2.00 mm 3.3V Key pin SFUIxxxxKgBP2xx-t-xx-2f1-3K0 2.00 mm 3.3V NC Pin 10 Hole LED Shield NC For operational indication (NC on request) (grounded on request) (no LED on request) Key pin g = hardware generation t = temperature grade (C=0C to 70C and I=-40C to +85C) f = firmware generation per product type Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 10 of 17 Figure 5: Component region on connector side (general tolerance 0.2mm) Figure 6: Component region on flash side (symmetric to center line, general tolerance 0.2mm) mirrored (view from connector side) Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 11 of 17 12 RoHS and WEEE update from Swissbit Dear Valued Customer, We at Swissbit place great value on the environment and thus pay close attention to the diverse aspects of manufacturing environmentally and health friendly products. The European Parliament and the Council of the European Union have published two Directives defining a European standard for environmental protection. This states that CompactFlash Cards must comply with both Directives in order for them to be sold on the European market: RoHS - Restriction of Hazardous Substances WEEE - Waste Electrical and Electronic Equipment Swissbit would like to take this opportunity to inform our customers about the measures we have implemented to adapt all our products to the European norms. What is the WEEE Directive (2012/19/EC)? The Directive covers the following points: Prevention of WEEE Recovery, recycling and other measures leading to a minimization of wastage of electronic and electrical equipment Improvement in the quality of environmental performance of all operators involved in the EEE life cycle, as well as measures to incorporate those involved at the EEE waste disposal points What are the key elements? The WEEE Directive covers the following responsibilities on the part of producers: Producers must draft a disposal or recovery scheme to dispose of EEE correctly. Producers must be registered as producers in the country in which they distribute the goods. They must also supply and publish information about the EEE categories. Producers are obliged to finance the collection, treatment and disposal of WEEE. Inclusion of WEEE logos on devices In reference to the Directive, the WEEE logo must be printed directly on all devices that have sufficient space. In exceptional cases where this is necessary because of the size of the product, the symbol of the WEEE Directive shall be printed on the packaging, on the instructions of use and on the warranty (WEEE Directive 2012/19/EC) When does the WEEE Directive take effect? The Directive came into effect internationally on July 04, 2012. What is RoHS (2011/65/EU)? The goals of the Directive are to: Place less of a burden on human health and to protect the environment by restricting the use of hazardous substances in new electrical and electronic devices To support the WEEE Directive (see above) RoHS enforces the restriction of the following 6 hazardous substances in electronic and electrical devices: Lead (Pb) - no more than 0.1% by weight in homogeneous materials Mercury (Hg) - no more than 0.1% by weight in homogeneous materials Cadmium (Cd) - no more than 0.01% by weight in homogeneous materials Chromium (Cr6+) - no more than 0.1% by weight in homogeneous materials PBB, PBDE - no more than 0.1% by weight in homogeneous materials Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 12 of 17 Swissbit is obliged to minimize the hazardous substances in the products. According to part of the Directive, manufacturers are obliged to make a self-declaration for all devices with RoHS. Swissbit carried out intensive tests to comply with the self-declaration. We have also already taken steps to have the analyses of the individual components guaranteed by third-party companies. Swissbit carried out the following steps during the year with the goal of offering our customers products that are fully compliant with the RoHS Directive. Preparing all far-reaching directives, logistical enhancements and alternatives regarding the full understanding and introduction of the RoHS Directive's standards Checking the components and raw materials: o o Replacing non-RoHS-compliant components and raw materials in the supply chain Cooperating closely with suppliers regarding the certification of all components and raw materials used by Swissbit Modifying the manufacturing processes and procedures o Successfully adapting and optimizing the new management-free integration process in the supply chain o Updating existing production procedures and introducing the new procedures to support the integration process and the sorting of materials Carrying out the quality process o Performing detailed function and safety tests to ensure the continuous high quality of the Swissbit product line When does the RoHS Directive take effect? As of June 08, 2011 only new electrical and electronic devices with approved quantities of RoHS will be put on the market. When will Swissbit be offering RoHS-approved products? Swissbit's RoHS-approved products are available now. Please contact your Swissbit contact person to find out more about exchanging your existing products for RoHS-compliant devices. For your attention We understand that packaging and accessories are not EEE material and are therefore not subject to the WEEE or RoHS Directives. Contact details: Swissbit AG Industriestrasse 4 CH 9552 Bronschhofen Tel: +41 71 913 03 03 - Fax: +41 71 913 03 15 E-mail: industrial@swissbit.com - Website: www.swissbit.com Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 13 of 17 13 Best Practices There are a number of best practices to reach the maximum life time. 13.1 Wear Leveling and Spare Block Management The device uses zone based flash management (zones also called as management units). This means that the user accessible data range (LBA area) is evenly divided into multiple zones, which are all managed separately for both, wear leveling (dynamic and static) and for spare & bad block management. USB HOST INTERFACE USB FLASH DRIVE FIRST SECTOR (LBA 0) ZONE 1 (MU1) LAST SECTOR ZONE 2 (MU2) ZONE 3 (MU3) ZONE 4 (MU4) *MU=Management Unit The number of zones is depending on the device density and can be read out using the Swissbit Life Time Monitoring tool. The tool will show the number of available spare blocks per management unit (zone). The devices need a minimum number of 2 spare blocks per unit to work with. If the first unit reaches this value, the device will be write-protected by the firmware. To get optimal life time, write accesses must be evenly distributed over all zones. This can, for example, be achieved by using multiple partitions and by then distributing the data between the partitions. 13.1 Device Removal & Power Failure User data can be lost or corrupted if power is interrupted while the UFD is writing data. To avoid data loss, it is necessary to avoid power interruption while the device is busy. This can be made sure by always using the host (e.g. Windows) shutdown mechanisms or by detaching the device in the operating system before unplugging it. Swissbit also offers an Application Note "Design-In Guide" that describes techniques to reduce data loss on power failure, if power failure absolutely can't be avoided. 13.2 Lifetime end handling If the flash reaches its end of life, the number of bad blocks will increase (bad flash blocks will be replaced with spare blocks). There exist different side effects with negative data influence by degraded flash cells. Sometimes bit errors can occur because of effects that are not immediately detected by the flash, e.g. effects like program disturb or read disturb, which means that the bad block recognition does not always prevent data loss. When the number of bit errors in a sector exceeds the ECC correcting capabilities, invalid (uncorrected) data can be reported back to the host. Because of these effects it is strongly recommended to replace devices that are nearing their end of life. One good indicator would be the current spare blocks per unit should not be reducing below 5. It is in the responsibility of the system integrator to account for the flash usage per zone. Swissbit offers support for calculating expected life time if the exact use case is provided (e.g. by providing low level [USB interface] write statistics). For notes on reducing flash stress, Swissbit offers an Application Note called "Design-In Guide". Please contact your sales channel for more information or send a mail to sales@swissbit.com. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 14 of 17 14 Part Number Decoder S F UI 4096 J 1 B P 2 TO 1 2 3 4 5 6 7 8 9 10 Manuf. Memory Type. Product Type Density Platform Product Generation Memory Organization 1. Manufacturer 2. Memory Type - I 11 - D T 12 13 - 211 14 - STD 15 Option Configuration Manuf. Code: Flash Mode Manuf. Code: Flash Package Temp. Option Flash vendor Code Number of flash chips/channels Technology Swissbit S Flash F U-1xx USB Flash Drive Module (Internal) UI 3. Product Type 4. Density 1 GB 2 GB 4 GB 8 GB 16 GB 1024 2048 4096 8192 16GB 5. Platform U-1xx - 2.54mm plug U-1xx - 2.00mm plug J K x8 B U-100 technology U-110 technology F P 1 Flash 2 Flash 1 2 Toshiba Micron TO MT 6. Product Generation 7. Memory Organization 8. Technology 9. Number of Flash channels 10. Flash Code 11. Temp. Option Industrial Temp. Range -40C to 85C Extended Temp. Range -25C to 85C Standard Temp. Range 0C to 70C I E C SLC MONO SLC DDP SLC QDP M D Q 12. DIE Classification (single die package) (dual die package) (quad die package) 13. PIN Mode Normal nCE & R/nB Dual nCE & Dual R/nB Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com 0/S 1/T Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 15 of 17 14. UFD XYZ X Setting Fix Drive 2 Y Firmware revision per product generation Revision 1 Revision 2 Revision 3 1 2 3 Z Optional setting default 1 15. Option Swissbit / Standard 5V supply Swissbit / Standard 3.3V supply *) Customized version *) max 3.6V allowed STD 3V3 XXX 15 Label 15.5 10.5 SFUIxxxxXXBPXXX -X-XX-XXX-XXX XXXXXXXX XXXXXXXX Swissbit SFUIxxxxxxBPxxx -x-xx-xxx-xxx xxxxxxxx xxxxxx Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Part Number Lot Code Type No. Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 16 of 17 16 Revision History Document Revision History Date 23-November-2009 28-October-2010 18-June-2012 29-August-2012 13-December-2012 04-June-2013 02-July-2013 07-April-2014 03-June-2014 Revision 1.00 1.10 1.20 1.21 1.30 1.40 1.41 1.50 1.60 Revision Details Final release General part numbers update, speed values for Toshiba flash Add 16GB UFD, add best practices 16GB Performance adapted (better data reliability) New CE Declaration min voltage specification for standard products dependent on density (3.25...3.80V) Min. voltage specification, add additional 3.3V variation Added FW rev. 3 for 16GB and removed CE declaration Added low profile drawings, added variation table and changed the order information Disclaimer: No part of this document may be copied or reproduced in any form or by any means, or transferred to any third party, without the prior written consent of an authorized representative of Swissbit AG ("SWISSBIT"). The information in this document is subject to change without notice. SWISSBIT assumes no responsibility for any errors or omissions that may appear in this document, and disclaims responsibility for any consequences resulting from the use of the information set forth herein. SWISSBIT makes no commitments to update or to keep current information contained in this document. The products listed in this document are not suitable for use in applications such as, but not limited to, aircraft control systems, aerospace equipment, submarine cables, nuclear reactor control systems and life support systems. Moreover, SWISSBIT does not recommend or approve the use of any of its products in life support devices or systems or in any application where failure could result in injury or death. If a customer wishes to use SWISSBIT products in applications not intended by SWISSBIT, said customer must contact an authorized SWISSBIT representative to determine SWISSBIT willingness to support a given application. The information set forth in this document does not convey any license under the copyrights, patent rights, trademarks or other intellectual property rights claimed and owned by SWISSBIT. The information set forth in this document is considered to be "Proprietary" and "Confidential" property owned by SWISSBIT. ALL PRODUCTS SOLD BY SWISSBIT ARE COVERED BY THE PROVISIONS APPEARING IN SWISSBIT'S TERMS AND CONDITIONS OF SALE ONLY, INCLUDING THE LIMITATIONS OF LIABILITY, WARRANTY AND INFRINGEMENT PROVISIONS. SWISSBIT MAKES NO WARRANTIES OF ANY KIND, EXPRESS, STATUTORY, IMPLIED OR OTHERWISE, REGARDING INFORMATION SET FORTH HEREIN OR REGARDING THE FREEDOM OF THE DESCRIBED PRODUCTS FROM INTELLECTUAL PROPERTY INFRINGEMENT, AND EXPRESSLY DISCLAIMS ANY SUCH WARRANTIES INCLUDING WITHOUT LIMITATION ANY EXPRESS, STATUTORY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. (c)2014 SWISSBIT AG All rights reserved. Swissbit AG Industriestrasse 4 CH-9552 Bronschhofen Switzerland Swissbit reserves the right to change products or specifications without notice. www.swissbit.com industrial@swissbit.com Revision: 1.60 U-110_data_sheet_UI-xxBP_Rev160 Page 17 of 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Swissbit: SFUI1024J1BP2TO-I-MS-211-STD SFUI16GBJ1BP2MT-C-QT-231-STD SFUI8192J3BP2TO-C-QT-221-STD SFUI4096J3BP2TO-C-DT-221-STD SFUI2048J3BP2TO-C-MS-221-STD SFUI1024J1BP2TO-C-MS-211-STD