Kellems(R) Wire Management Products www.hubbell-wiring.com Pulling Grips Support Grips Strain Relief Grips Cord Connectors Index Index Product Page Kellems(R) Wire Mesh Grips Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-2 Quick Reference Selection Guide for Grip Applications . . . . . . . . . . . . . . . . . . . .T-4 Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-5 Overhead DUA-PULL(R) Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-6 Overhead Multiple Strength Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-7 Underground K-Type Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-8 Underground T-Type Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-9 Special Purpose Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-10 Low Tension Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-12 Wire Rope Splicing Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-13 Cable Splicing Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-14 Tools and Bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-15 Swivels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-16 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-17 Support Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-28 Standard Duty Support Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-30 Heavy Support Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-34 Service Drop Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-36 Bus Drop Support Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-38 Conduit Riser Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-39 Support Grips Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-42 Conduit Riser Grips Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-47 Fiber Optic Cable Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-49 Pulling Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-50 Support Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-53 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-54 Hose Containment Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-58 Strain Relief Grips for Flexible Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-59 Deluxe Cord Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-60 PG and Metric Threaded Deluxe Cord Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-64 Dust-Tight Strain Relief Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-65 I-Grips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-66 Adapters for Multi-Pin Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-67 Strain Relief Grips for Liquidtight Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-68 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-71 Cord Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-81 Straight Male Cord Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-82 45 Male Cord Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-85 90 Male Cord Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-86 Straight Female and Underground Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-87 Low Profile N .P .T ., PG and Metric Thread Connectors . . . . . . . . . . . . . . . . . . . .T-88 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-89 Hubbell Juniors(R) Miniature Nylon Cord Connectors . . . . . . . . . . . . . . . . . . . . . .T-90 Cord Connectors Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-92 Hubbell Juniors(R) Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-102 PolyTuff(R) Non-Metallic Liquidtight Conduit and Tubing . . . . . . . . . . . . . . . . . .T-104 PolyTuff(R) Non-Metallic Liquidtight Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-106 Metallic Liquidtight Conduit Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-108 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-110 Kellems(R) Wire Management Products Section T T-1 Kellems(R) Wire Management Products Wire Management Products Kellems(R) Wire Mesh Grips Diagram Bus Drop Support Grip Flexible Conduit Grip Support Grip Support Grip INDUSTRY Deluxe Cord Grip Flexible Conduit Grip Strain Relief Grip To help you fully visualize the variety of uses available to you through Hubbell-Kellems Mesh Grips, we have prepared this diagram of common applications . It follows the typical pattern of usage you would find traveling from utility to industrial, commercial and residential environments . Pulling Grips are instrumental in the installations of transmission lines, service lines and cabling for construction and maintenance . Support Grips provide holding management for indoor and outdoor permanent cable installations . Kellems(R) Wire Mesh Grips Diagram Strain Relief Grips are most often used to provide maximum reliability and minimum maintenance in areas where cords on machinery or equipment is impacted by motion or vibration or at risk of damage from cable pullout . Beyond the electrical applications illustrated here, Hubbell-Kellems Mesh Grips can be used for wire management on radio and microwave communications towers, crane and hoist wire rope maintenance, elevator cable management and more . Support Grip Conduit Support Grip UTILITY T-2 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Overhead Pulling Grip UTILITY Bus Drop Support Grip Deluxe Cord Grip Bus Drop Support Grip Underground Pulling Grip INDUSTRY Hose Containment Grip Strain Relief Grip Conduit Support Kellems(R) Wire Mesh Grips Diagram Support Grip Underground Pulling Grip COMMERCIAL Dimensions in Inches (cm) RESIDENTIAL www.hubbell-wiring.com T-3 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Quick Reference Selection Guide for Grip Applications Pulling Grips Heavy-Duty Rotating Eye For underground wiring and overhead heavy-duty pulling of service lines and new construction cable . See pages T-7 and T-8 . Slack Grips For removing underground cable and pulling slack in existing cable and new installations and when end of cable is not available . See pages T-10 and T-11 . Heavy-Duty Flexible Eye For overhead transmission and distribution line stringing . See pages T-6, T-7, and T-9 . Light-Duty Flexible Eye For light industrial pulling of electrical cable and for underground and industrial plant wiring and re-wiring . See page T-12 . Quick Reference Selection Guide for Grip Applications Support Grips Single Eye For single hook attachment of permanent indoor/outdoor cable . Available on heavy-duty, standard duty, and service drop grips . See pages T-30, T-34, and T-36 . Support Grips Wide Range Bus Drop Used indoors for cable support where flexible cable connects electrical equipment to bus duct . Support air hose and water hose . See page T-38 . Double Eye For double hook attachment of permanent indoor/ outdoor cable . Available on heavy-duty and standard duty grips . See pages T-31 and T-35 . Single Offset Eye For offset hook attachment of permanent indoor/ outdoor cable . Available on standard duty and light-duty support grips . See page T-32 . Universal Eye Used to fasten around a structure or closed loop . Available on standard duty support and light or heavy duty service drop grips . See pages T-33 and T-37 . Strain Relief Grips Deluxe Cord Indoor or outdoor use where subject to moisture, splash, or washdown . Examples are enclosures, crane hoist and pendant drop stations, hand tools, pumps, and processing equipment . Available in straight, 90, or 45 configurations . See pages T-60 to T-64 . Dust-Tight Strain Relief Indoor use only for wiring of electrical enclosures, machine tools, portable power tools, bus drop cable systems . See page T-65 . Liquid-Tight, Flexible Metal Conduit Wiring of machine tools, electrical enclosures, motors, and systems subjected to vibration, flexure, motion, or strain . Available in straight, 90, or 45 configurations . See pages T-68 to T-70 . Other Specialty Grips Splicing Grips Used as temporary splice for cable and wire rope, or as reinforcement to protect cables and hoses . See pages T-13 and T-14 . Specifications are subject to change without notice. T-4 Conduit Riser Grips Ideal for supporting electrical wires inside rigid conduit via a supporting ring . See pages T-39 to T-41 . Hose Containment Grips Used on flexible hose lines to prevent violent whipping of hose in the event of failure at the fitting . See page T-58 . www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Pulling Grips Overhead, Underground, Commercial Construction, Specialty Flexible or rotating eyes will mate easily with line stringing swivels for attachment to pulling lines; they have great strength for trouble free pulling jobs Shoulder protectors contain the cable inside the grip and smooth the passage of the grip over line stringing blocks or conduit bends; they protect the leading edge of the grip from abrasion The galvanized steel mesh grip provides strength for secure pulling jobs and a slim profile with little build-up; it has flexibility to follow cable path The multiweave styles available add strength for big pulling jobs and provide positive gripping power Endless weave allows easy installation onto cable . It has a snag-free low profile; designed to be a reusable tool Pulling Grips Dimensions in Inches (cm) www.hubbell-wiring.com T-5 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Overhead DUA-PULL(R) Pulling Grips Flexible Eye, Double Weave Mesh, Galvanized Steel WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . DUA-PULL(R) Grips DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead transmission line stringing applications . They have a dual function, not provided by any other grip, of working with both bare and insulated conductors and synthetic rope . DUA-PULL(R) Grips Diameter Range Conductor Diameter Inches (cm) Rope* Diameter Inches (cm) Approx. Breaking Strength Lbs. (N) E In. (cm) M In. (cm) Eye B Diameter In. (cm) Over Cable & Grip** In. (cm) Diameter Color Code Catalog Number 033271037 .19"- .37" ( .48- .94) .25"- .65" ( .63-1 .65) 6,500 (28,912) 10" (25 .40) 24" (60 .96) .220" ( .56) .200" ( .51) Black .38"- .62" ( .97-1 .57) .50"- .90" (1 .27-2 .29) 14,000 (62,272) 12" (30 .48) 36" (91 .44) .375" ( .95) .280" ( .71) Dk Green 033271038 .63"- .87" (1 .60-2 .21) .75"-1 .10" (1 .90-2 .79) 20,000 (88,960) 13" (33 .02) 48" (121 .92) .437" (1 .11) .360" ( .91) .88"-1 .12" (2 .24-2 .84) 1 .00"-1 .50" (2 .54-3 .81) 30,600 (136,109) 15" (38 .10) 60" (152 .40) .500" (1 .27) .500" (1 .27) Dk Blue Red 033271039 033271040 1 .13"-1 .37" (2 .87-3 .48) 1 .25"-1 .70" (3 .17-4 .32) 46,800 (208,166) 18" (45 .72) 76" (193 .04) .625" (1 .59) .625" (1 .59) Yellow 033271041 1 .38"-1 .90" (3 .51-4 .38) 1 .50"-2 .10" (3 .81-5 .33) 66,500 (295,792) 24" (60 .96) 89" (226 .06) .750" (1 .90) .750" (1 .90) Alum . 033271042 Overhead DUA-PULL(R) Pulling Grips Note: E- Eye length. M-Mesh length at nominal diameter. * For rope, select smallest size grip which meets required work load. ** Add to cable or rope diameter. DUA-PULL(R) Feed Tube For Use with DUA- PULL Grip T-6 Rope Diameter Inches (cm) Feed Tube Length Inches (cm) Catalog Number 033271037 .25"- .65" ( .63-1 .65) 28" (71 .12) 091061043 033271038 .50"- .90" (1 .27-2 .29) 40" (101 .60) 091061044 033271039 .75"-1 .10" (1 .90-2 .79) 52" (132 .08) 091061045 033271040 1 .00"-1 .50" (2 .54-3 .81) 67" (170 .18) 091061046 033271041 1 .25"-1 .70" (3 .17-4 .32) 83" (210 .82) 091061047 033271042 1 .50"-2 .10" (3 .81-5 .33) 96" (243 .84) 091061048 www.hubbell-wiring.com Dimensions in Inches (cm) Overhead Multiple Strength Pulling Grips Flexible or Rotating Eye, Triple, Double, Single Weave, Galvanized Steel Multiple Strength Style Grips Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare conductor, ground wires, messenger strands, wire rope and insulated cables . WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Multiple Strength Grip-Rotating Eye Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Rotating Eye Dia. Inches (cm) Color Code Catalog Number .25"- .49" ( .63-1 .24) .50"- .74" (1 .27-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-2 .24" (4 .44-5 .69) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 6,800 (20,567) 10,000 (44,480) 14,400 (64,051) 24,600 (109,420) 30,600 (136,109) 30,600 (136,109) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 5" (12 .70) 6" (15 .24) 6" (15 .24) 8" (20 .32) 8" (20 .32) 9" (22 .86) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 26" (66 .04) 32" (81 .28) 41" (104 .14) 52" (132 .08) 56" (142 .24) 60" (152 .40) 70" (177 .80) 50" (127 .00) 52" (132 .08) 54" (137 .16) 58" (142 .24) " (2 .22) 1" (2 .54) 1" (2 .54) 1" (3 .49) 1" (4 .13) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) Dark Green Brown Light Blue Gold Black Red Dark Blue Yellow Orange Aluminum Light Green 03302016 03302018 03302020 03302022 03302024 03302026 03302028 03302066 03302097 033021030 033021031 Note: E- Eye length. M-Mesh length at nominal diameter. Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) A-Eye Dia. Inches (cm) Color Code Catalog Number .25"- .49" ( .63-1 .24) .50"- .74" (1 .27-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-2 .24" (4 .44-5 .69) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 6,800 (20,567) 10,000 (44,480) 14,400 (64,051) 24,600 (109,420) 30,600 (136,109) 30,600 (136,109) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 9" (22 .86) 9" (22 .86) 11" (27 .94) 12" (30 .48) 12" (30 .48) 12" (30 .48) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 26" (66 .04) 32" (81 .28) 41" (104 .14) 52" (132 .08) 56" (142 .24) 60" (152 .40) 70" (177 .80) 50" (127 .00) 52" (132 .08) 54" (137 .16) 58" (142 .24) " ( .63) " ( .79) " ( .95) " (1 .27) " (1 .27) " (1 .27) " (1 .59) " (1 .59) " (1 .59) " (1 .59) " (1 .59) Dark Green Brown Light Blue Gold Black Red Dark Blue Yellow Orange Aluminum Light Green 03302044 03302046 03302048 03302050 03302052 03302054 03302056 033021078 033021079 033021080 033021081 Note: E- Eye length. M-Mesh length at nominal diameter. Dimensions in Inches (cm) www.hubbell-wiring.com T-7 Overhead Multiple Strength Pulling Grips Multiple Strength Grip-Flexible Eye Kellems(R) Wire Management Products Kellems(R) Wire Management Products Underground K-Type Pulling Grips Rotating Eye, Double Weave, Galvanized Steel WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . K-Type Grips Kellems(R) Rotating Eye, K-Type Pulling Grips are made of high strength galvanized steel strand . All Grips feature double weave mesh for greater strength and added mesh contact on the table, to handle longer or heavier pulling jobs . The forged eye mates easily with a swivel or shackle . K-Type Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E In. (cm) M In. (cm) Rotating Eye Diameter Inches (cm) Catalog Number 5,600 (24,909) 6,800 (30,246) 6,800 (30,246) 12,800 (56,934) 12,800 (56,934) 16,400 (72,941) 27,200 (120,986) 33,000 (146,784) 41,000 (182,368) 48,000 (213,504) 48,000 (213,504) 5" (12 .70) 5" (12 .70) 6" (15 .24) 7" (17 .78) 7" (17 .78) 7" (17 .78) 8" (20 .32) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 11" (27 .94) 11" (27 .94) 20" (50 .80) 20" (50 .80) 21" (53 .34) 25" (63 .50) 26" (66 .04) 28" (71 .12) 30" (76 .20) 32" (81 .28) 33" (83 .82) " (2 .22) " (2 .22) 1" (2 .54) 1" (3 .49) 1" (3 .49) 1" (3 .49) 1" (4 .13) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 03301001 03301002 03301013 03301014 03301016 03301017 03301018 03301019 03301020 03301021 033011017 5,600 (24,909) 6,800 (30,246) 9,600 (42,701) 16,400 (72,947) 16,400 (72,947) 27,200 (120,986) 33,000 (146,784) 41,000 (182,368) 48,000 (213,504) 48,000 (213,504) 48,000 (213,504) 40,000 (177,920) 54,000 (240,192) 5" (12 .70) 5" (12 .70) 6" (15 .24) 7" (17 .78) 7" (17 .78) 9" (22 .86) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 16" (40 .64) 16" (40 .64) 32" (81 .28) 33" (83 .82) 34" (86 .36) 36" (91 .44) 38" (96 .52) 39" (99 .06) 41" (104 .14) 42" (106 .68) 58" (147 .32) 60" (152 .40) 66" (167 .64) " (2 .22) " (2 .22) 1" (2 .54) 1" (3 .49) 1" (3 .49) 1" (4 .13) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 1" (4 .76) 03301011 03301012 03301024 03301025 03301026 03301027 03301028 03301029 03301030 03301031 03301039 03301047 03301045 Short Underground K-Type Pulling Grips .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 4 .00"-4 .49" (10 .16-11 .40) Standard .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .49" (2 .54-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 4 .00"-4 .49" (10 .16-11 .40) 4 .50"-4 .99" (11 .43-12 .67) 5 .00"-5 .99" (12 .70-15 .21) 6 .00"-6 .99" (15 .24-17 .75) Note: E- Eye length. M-Mesh length at nominal diameter. See page T-26 for multiple cables in a single pulling grip. T-8 www.hubbell-wiring.com Dimensions in Inches (cm) Underground T-Type Pulling Grips Flexible Eye, Double Weave, Galvanized Steel T-Type Grips Kellems(R) Flexible T-Type Pulling Grips are made of high strength galvanized steel strand . They feature double weave mesh for positive holding power in medium to heavy pulling jobs . The grip eye will easily attach to a swivel . WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products T-Type Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number 4,500 (20,016) 5,600 (24,909) 6,800 (30,246) 9,600 (42,701) 16,400 (72,947) 18,500 (82,288) 24,500 (108,976) 24,500 (108,976) 31,000 (137,888) 8" (20 .32) 8" (20 .32) 9" (22 .86) 9" (22 .86) 11" (27 .94) 12" (30 .48) 12" (30 .48) 14" (35 .56) 14" (35 .56) 21" (53 .34) 24" (60 .96) 24" (60 .96) 24" (60 .96) 24" (60 .96) 24" (60 .96) 24" (60 .96) 24" (60 .96) 26" (66 .04) 033041082 033041083 033041084 033041085 033041086 033041087 033041088 033041089 033041090 6,800 (30,246) 9,600 (42,701) 16,400 (72,947) 18,500 (82,288) 24,500 (108,976) 24,500 (108,976) 31,000 (137,888) 9" (22 .86) 9" (22 .86) 11" (27 .94) 12" (30 .48) 12" (30 .48) 14" (35 .56) 14" (35 .56) 36" (91 .44) 36" (91 .44) 36" (91 .44) 36" (91 .44) 36" (91 .44) 36" (91 .44) 40" (101 .60) 033041091 033041092 033041093 033041094 033041095 033041096 033041097 Short .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .49" (2 .54-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) Standard Note: E- Eye length. M-Mesh length at nominal diameter. See page T-26 for multiple cables in a single pulling grip. Dimensions in Inches (cm) www.hubbell-wiring.com T-9 Underground T-Type Pulling Grips .75"- .99" (1 .90-2 .51) 1 .00"-1 .49" (2 .54-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) Kellems(R) Wire Management Products Special Purpose Pulling Grips Kellems(R) Wire Management Products Special Purpose Pulling Grips Non-Conductive and Slack Pulling WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Non-Conductive Grips, Single Eye, Double Weave, Non-Metallic Kellems(R) Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid fiber, are available for pulling single cable or cable bundles . Their braided double weave design adds strength and positive holding power . Slack Pulling Grips are offered in three styles made of galvanized steel . The closed type is used when the cable end is accessible . When not accessible, there are split lace and split rod closing styles . All grips feature a single offset eye for easy attachment to a pulling line . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) .50"- .62" (1 .27-1 .57) 4,000 (17,792) 5 .5" (13 .97) 24" (60 .96) .44" (1 .12) Green 03628001 .63"- .74" (1 .60-1 .88) 5,000 (22,240) 5 .5" (13 .97) 26" (66 .04) .44" (1 .12) Yellow 03628002 .75"- .99" (1 .90-2 .51) 6,000 (26,688) 6 .0" (15 .24) 31" (78 .74) .63" (1 .60) Red 03628003 1 .00"-1 .24" (2 .54-3 .15) 6,000 (26,688) 6 .5" (16 .51) 36" (91 .44) .63" (1 .60) Blue 03628004 E In. (cm) M In. (cm) A In. (cm) Color Code Catalog Number 1 .25"-1 .49" (3 .17-3 .78) 6,000 (26,688) 6 .7" (17 .02) 41 .5" (105 .41) .63" (1 .60) White 03628005 1 .50"-1 .99" (3 .815 .05) 03628006 6,000 (26,688) 8 .0" (20 .32) 44 .0" (121 .76) .63" (1 .60) Pink Slack Grip-Closed Mesh, Offset Eye, Double Weave, Galvanized Steel Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number Standard .75"- .99" (1 .90-2 .51) 2,600 (11,565) 7" (17 .78) 12" (30 .48) 03308003 1 .00"-1 .24" (2 .54-3 .15) 4,000 (17,792) 8" (20 .32) 15" (38 .10) 03308004 1 .25"-1 .49" (3 .17-3 .78) 5,400 (24,019) 8" (20 .32) 16" (40 .64) 03308005 1 .50"-1 .74" (3 .81-4 .42) 6,600 (29,357) 8" (20 .32) 20" (50 .80) 03308006 1 .75"-1 .99" (4 .44-5 .05) 10,000 (44,480) 10" (25 .40) 18" (45 .72) 03308007 2 .00"-2 .49" (5 .08-6 .32) 11,000 (48,928) 10" (25 .40) 19" (48 .26) 03308008 2 .50"-2 .99" (6 .35-7 .59) 11,000 (48,928) 10" (25 .40) 20" (50 .80) 03308009 3 .00"-3 .49" (7 .62-8 .86) 14,500 (64,496) 12" (30 .48) 21" (53 .34) 03308010 3 .50"-3 .99" (8 .89-10 .13) 14,500 (64,496) 12" (30 .48) 22" (55 .88) 03308011 Note: E- Eye length. M-Mesh length at nominal diameter. See page T-26 for multiple cables in a single pulling grip. T-10 www.hubbell-wiring.com Dimensions in Inches (cm) Special Purpose Pulling Grips Slack Pulling WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Slack Grip-Split Mesh, Rawhide Lace Closing, Offset Eye, Double Weave, Galvanized Steel Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number 2,500 (11,120) 3,500 (15,568) 4,000 (17,792) 4,000 (17,792) 4,000 (17,792) 4,000 (17,792) 4,000 (17,792) 7" (17 .78) 8" (20 .32) 8" (20 .32) 9" (22 .86) 10" (25 .40) 10" (25 .40) 10" (25 .40) 12" (30 .48) 15" (38 .10) 16" (40 .64) 17" (43 .18) 18" (45 .72) 19" (48 .26) 20" (50 .80) 03309003 03309004 03309005 03309006 03309007 03309008 03309009 4,000 (17,792) 4,000 (17,792) 4,000 (17,792) 4,000 (17,792) 4,000 (17,792) 9" (22 .86) 10" (25 .40) 10" (25 .40) 12" (30 .48) 12" (30 .48) 25" (63 .50) 26" (66 .04) 29" (73 .66) 32" (81 .28) 35" (88 .90) 03309015 03309016 03309017 03309018 03309019 Standard .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) Slack Pulling Grips are offered in three styles made of galvanized steel . The closed type is used when the cable end is accessible . When not accessible, there are split lace and split rod closing styles . All grips feature single offset eye for easy attachment to a pulling line . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Long 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) Special Purpose Pulling Grips Slack Grip-Split Mesh, Rod Closing, Offset Eye, Single Weave, Galvanized Steel Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .61" (1 .27-1 .55) .62"- .74" (1 .57-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75" -1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 1,500 (6,672) 1,800 (8,006) 2,200 (9,786) 3,400 (15,123) 4,500 (20,016) 5,800 (25,798) 7,600 (33,805) 9,000 (40,032) 11,000 (48,928) 12,000 (53,376) 12,000 (53,376) 7" (17 .78) 7" (17 .78) 7" (17 .78) 8" (20 .32) 8" (20 .32) 9" (22 .86) 10" (25 .40) 10" (25 .40) 10" (25 .40) 12" (30 .48) 12" (30 .48) 6" (15 .24) 8" (20 .32) 10" (25 .40) 12" (30 .48) 14" (35 .56) 15" (38 .10) 16" (40 .64) 19" (48 .26) 20" (50 .80) 21" (53 .34) 24" (60 .96) 03310001 03310002 03310003 03310004 03310005 03310006 03310007 03310008 03310009 03310010 03310011 Note: E- Eye length. M-Mesh length at nominal diameter. See page T-26 for multiple cables in a single pulling grip. Dimensions in Inches (cm) www.hubbell-wiring.com T-11 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Low Tension Pulling Grips Flexible Eye, Single Weave, Galvanized Steel WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Light Duty Grips Light Duty Pulling Grips are made of galvanized steel in a single weave construction . They feature a flexible eye for easy attachment to a pulling line . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number 2,800 (12,454) 2,800 (12,454) 4,000 (17,792) 5,300 (23,574) 5,300 (23,574) 6,800 (30,246) 8,500 (37,808) 8,500 (37,808) 5" (12 .70) 5" (12 .70) 6" (15 .24) 7" (17 .78) 7" (17 .78) 8" (20 .32) 9" (22 .86) 9" (22 .86) 11" (27 .94) 11" (27 .94) 12" (30 .48) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 18" (45 .72) 03303001 03303002 03303003 03303004 03303005 03303006 03303007 03303008 2,800 (12,454) 2,800 (12,454) 4,000 (17,792) 6,800 (30,246) 6,800 (30,246) 6,800 (30,246) 8,500 (37,808) 10,600 (47,149) 14,700 (65,386) 14,700 (65,386) 5" (12 .70) 5" (12 .70) 6" (15 .24) 7" (17 .78) 7" (17 .78) 8" (20 .32) 9" (22 .86) 9" (22 .86) 10" (25 .40) 10" (25 .40) 16" (40 .64) 16" (40 .64) 20" (50 .80) 20" (50 .80) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 30" (76 .20) 32" (81 .28) 03303010 03303011 03303012 03303013 03303015 03303016 03303017 03303018 03303019 03303029 Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Model Catalog Number .19"- .24" ( .48- .61) .25"- .37" ( .63- .94) .38"- .49" ( .97-1 .24) .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 400 (1,779) 450 (2,002) 900 (4,003) 1,300 (5,782) 1,950 (8,674) 2,800 (12,454) 3,900 (17,347) 3" (8 .25) 3" (8 .25) 3" (9 .52) 4" (10 .79) 5" (12 .70) 5" (14 .60) 6" (16 .51) 4" (10 .79) 4" (10 .79) 7" (17 .78) 8" (21 .59) 10" (25 .40) 10" (25 .40) 11" (29 .21) J19 J25 J37 J50 J62 J75 J100 03305011* 03305001 03305002 03305003 03305004 03305005 03305006 Short .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) Standard Junior Pulling Grips feature a strong galvanized steel, single weave mesh . A flexible eye easily attaches to a pulling line, snake or fish tape . .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) Low Tension Pulling Grips Junior Grip Kit Junior Grip Kit contains 6 grips, one of each size . Catalog number 033051114 . Junior Pulling Grips Note: See page T-26 for multiple cables in a single pulling grip. See page T-27 for building wire selection chart. T-12 Note: E- Eye length. M-Mesh length at nominal diameter. * Not included in Junior Grip Kit, 033051114. www.hubbell-wiring.com Dimensions in Inches (cm) Wire Rope Splicing Grips Triple, Double, Single Weave, Galvanized Steel WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Regular Wire Rope Grips Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) Approx. Length Of Grip Feet (m) Catalog Number "- " (1 .43-1 .59) 7,500 (33,360) 5 .75 (1 .75) 03316001 "- " (1 .90-2 .22) 12,500 (55,600) 6 .75 (1 .90) 03316002 1"-1" (2 .54-2 .86) 16,000 (71,168) 7 .00 (2 .13) 03316003 1"- 1" (3 .17-3 .49) 20,000 (88,960) 8 .00 (2 .44) 03316004 1"- 1" (3 .49-3 .81) 20,000 (88,960) 8 .00 (2 .44) 03316006 Kellems(R) Wire Rope Grips are made of high strength galvanized steel strand in a construction of triple, double and single weave for superior gripping ability . They are available with or without a rotating barrel which will help eliminate twist in the old rope from being transferred to the new rope . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Rotating Wire Rope Grips Approx. Breaking Strength Lbs. (N) Approx. Length Of Grip Feet (m) Barrel Dimensions Lgth. x O.D. In. (cm) Catalog Number "- " (1 .11-1 .27) 5,000 (22,240) 5 .33 (1 .63) 3 .00" (7 .62) x .87" (2 .21) 03317001 "- " (1 .43-1 .59) 7,500 (33,360) 5 .83 (1 .78) 4 .25" (10 .79) x 1 .00" (2 .54) 03317002 "- " (1 .90-2 .22) 12,500 (55,600) 6 .50 (1 .98) 4 .25" (10 .79) x 1 .00" (2 .54) 03317003 1"- 1" (2 .54-2 .86) 16,000 (71,168) 8 .67 (2 .64) 5 .50" (13 .97) x 1 .37" (3 .48) 03317004 1"- 1" (3 .17-3 .49) 20,000 (88,960) 9 .00 (2 .74) 5 .50" (13 .97) x 1 .37" (3 .48) 03317005 1"- 1" (3 .81-4 .44) 20,000 (88,960) 11 .00 (3 .35) 5 .50" (13 .97) x 1 .37" (3 .48) 03317006 Dimensions in Inches (cm) www.hubbell-wiring.com Wire Rope Splicing Grips Cable Diameter Range Inches (cm) T-13 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Cable Splicing Grips Double Weave, Galvanized Steel / Single Weave, Galvanized Steel WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . Splicing Grip Splicing Grips are made of galvanized steel in double weave mesh construction . They are available in various lengths and sizes to suit most applications . Double Weave Tube Approx. Breaking Strength Lbs. (N) .37"- .49" ( .94-1 .24) 3,500 (15,568) Mesh Length Inches (cm) Catalog Number 18" (45 .72) 24" (60 .96) 36" (91 .44) 48" (121 .92) 72" (182 .88) 013041330 -- -- -- -- Cable Diameter Range Inches (cm) .50"- .61" (1 .27-1 .55) 3,500 (15,568) .62"- .74" (1 .57-1 .88) 4,400 (19,571) .75"- .99" (1 .90-2 .51) 7,500 (33,360) 1 .00"-1 .49" (2 .54-3 .78) 10,000 (44,480) 01304064 01304011 -- -- -- 01304009 01304013 013041234 -- -- -- 01304010 01304054 01304017 01304037 -- 01304015 01304055 01304029 013041333 Cable Splicing Grips Junior Splicing Grips, Single Weave Junior Splicing Grips are made of galvanized steel and are designed for use in very light duty and small splicing jobs . Junior Tube Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) Length @ Nom Diameter Inches (cm) Catalog Number .18"- .24" ( .46- .61) .25"- .36" ( .63- .91) 400 (1,779) 400 (1,779) 7" (17 .78) 8" (20 .32) 01301008 01301013 T-14 www.hubbell-wiring.com Dimensions in Inches (cm) Tools and Bands Pulling Grips Accessories Punch-Lok(R) Bands Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from being tripped or pulled loose . Also, they assure full gripping action by locking the mesh of the tail in tight contact with the cable or rope . Kellems(R) Wire Management Products Kellems(R) Wire Management Products When the tail of a grip is the leading end, the bands are particularly important to prevent accidental release caused by tripping on obstructions . A conductor-to-conductor (double-socking) pulling operation is a good example: where two grips connect two conductors to form a temporary splice . Bands should be applied to the ends of the grips as illustrated herein . It is also common practice to tape over the banded tail area to assure smooth passage through the sheaves .The conductor should be installed in the grip up to the elbows of the aluminum shoulders in order to assure full and complete gripping action . Punch-Lok Bands Grip Banding Range Inches (cm) Band Width Inches (cm) Band Inside Diameter Inches (cm) Model Catalog Number "-1" ( .63-2 .86) 1"-1" (2 .86-4 .13) 1"-2" (4 .13-5 .71) 2"-3" (5 .71-8 .89) 3"-5" (8 .89-12 .70) " ( .95) " ( .95) " (1 .59) " (1 .59) " (1 .59) 1" (3 .49) 2" (5 .08) 2" (6 .35) 4" (10 .16) 6" (15 .24) 0-311 0-316 0-10 0-16 0-24 20320050 20320051 20320052 20320053 20320054 Accessories Punch-Lok Tools Catalog Number P-1000 for use with " width Banding tool . P-38 for use with " and " width Banding tool for tight spaces . 20320048 20320047 Tools and Bands Description Note: In all cases two Punch-Lok Bands should be double wrapped approximately one inch to two inches (2.54cm to 5.08cm) from the grip's tail. Banding is required to ensure maximum reliability and guard against accidental release. Punch-Lok (R) is a registered trademark of Punch-Lok Inc. Dimensions in Inches (cm) www.hubbell-wiring.com T-15 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Swivels Pulling Grips Accessories WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-17 through T-27 . 20308001A Stainless Steel Swivels Swivels are essential to the efficiency and safety of any high tension application . They are particularly important where continuous pulls develop higher and higher torque levels . Torque is intensified by the pull-resistance of the cable itself and the resistance of the high tension controlling equipment regulating line sag . Ball bearing swivels release torque and prevent it from reaching dangerous levels that can damage the cable and obstruct the lines . C B A E D F G Stainless Steel Swivels Maximum Safe Working Load Lbs. (N) A B Dimensions in Inches (cm) C D E F G Model Catalog Number 2,250 (10,000) 5,000 (22,240) 9,000 (40,030) 10,000 (44,480) 30,000 (133,440) " (2 .22) 11/4" (3 .17) 11/2" (3 .81) 1" (4 .13) 2" (6 .03) 21/2" (6 .35) 3" (9 .37) 41/4" (10 .79) 41/2" (11 .43) 7" (19 .37) 3" (8 .57) 43/4" (12 .06) 5" (14 .29) 6" (15 .24) 10" (25 .40) " (0 .95) 1" (1 .35) 1" (1 .51) " (1 .75) 1" (2 .62) " (0 .79) " (1 .03) 1/2" (1 .27) " (1 .59) " (2 .22) " (2 .46) 1" (3 .25) 1" (3 .97) 1" (4 .36) 2" (7 .06) A-13L BB-13L B-13L C-13L D-13L 20308001A 20308002A 20308003A 20308004A 20308005A Swivels " (1 .11) 1" (1 .35) " (1 .75) 3/4" (1 .90) 1" (3 .02) T-16 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Pulling Grips Kellems Pulling Grips are reusable tools for pulling electrical cable, bare conductor or rope . They are easy and fast to install, providing the user with a smooth, slim profile that allows for easy passage through ducts, conduit, blocks and sheaves . Kellems Pulling Grips are made of the highest quality galvanized steel strand which assures the user of a long lasting grip . There is a Kellems Pulling Grip for every pulling job . CAUTION: It is very important to comply with all of the following precautions . Failure to do so may result in property damage, personal injury or death . 1 . Pulling grips are to be installed by a qualified individual in accordance with all applicable national and local safety, electrical and rigging codes . 2 . Ensure that the correct grip is selected for your specific needs . 3 . Do not use a pulling grip for any application other than pulling cable . 4 . Thoroughly examine the grip for damage . Do not use a damaged grip . 5 . Ensure that the recommended work load of the grip is suitable for the application . Never use grips at their approximated rated breaking strength . A safety factor of 5 is recommended for pulling grips . 6 . Do not alter grips in any way . For example, do not modify pulling eyes, shoulders, fittings or lugs . 7 . Do not attach any type of pulling hardware to any point on the grip other than the pulling eye . The pulling eye is the only acceptable means of attachment to external hardware . 8 . Always apply 2 bands at 1" and 2" respectively, from the tail end of the mesh to guard against accidental release of the grip . Accidental release can occur if an object contracts and pushes against the tail end of the mesh, thereby expanding and releasing its hold . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Select The Correct Pulling Grip Each Kellems Grip is designed to work on a specific range of cable diameters . Step 1 Refer to the chart below to determine the style of grip best suited for your application . Step 2 Determine your cable outside diameter . Step 3 Find the grip size that encompasses your cable diameter . Step 4 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed approximate breaking strength of the grip to insure that the grip will be strong enough . Refer to page T-18 for safety and working load factors . Pulling Grip Selection Chart Grip Style Application Page Number DUA-PULL(R), flexible eye Dimensions in Inches (cm) www.hubbell-wiring.com T-6 T-7 T-7 T-8 T-9 T-10 T-10 T-11 T-11 T-12 T-12 T-13 T-14 T-15, T-16 T-50, T-51, T-52 T-17 Technical Information Extra high strength overhead transmission line stringing for bare or insulated conductor and synthetic rope . Multiple strength, flexible eye Normal overhead transmission and distribution line stringing for bare or insulated conductor . Multiple strength, rotating eye Normal overhead transmission and distribution line stringing for bare or insulated conductor . K-type grip, rotating eye Underground power cables and communication lines . Service lines into factories . T-type grip, flexible eye Underground power cables and communication lines . Service lines into factories . Non-conductive, flexible eye Pull insulated distribution cable into place . Slack pulling, closed mesh Remove underground cable . For pulling slack in final placement of new cable when end of cable is available . Slack pulling, split mesh, Remove underground cable . For pulling slack in final placement of new cable rawhide lace closing when end of cable is not available . Slack pulling, split mesh, Remove underground cable . For pulling slack in final placement of new cable rod closing when end of cable is not available, with rod closing for quick installation . Light duty, flexible eye Light pulling, underground electrical construction . Industrial plant wiring and rewiring jobs . Junior, flexible eye Connect bundled insulated building wire to a pulling tape . Pull wire through conduit . Regular and rotating wire rope Restring wire rope in cranes and oil rigs . Splicing Temporary splice for cable or wire rope . Pulling Grip Accessories Tools, bands, swivels . Fiber Optic Cable Pulling Grips Pull fiber optic cable into place overhead, underground or through duct and conduit . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Pulling Grips Safety And Working Load Factors For Wire Mesh Grips The broad application of Kellems grips on a wide variety of objects requires that adequate safety factors be used to establish working loads . The approximate breaking strength of a Kellems grip represents an average calculation based on data established from actual direct tension testing done in our engineering laboratories . It is impossible to catalog or guarantee a safety factor suitable for all applications as operating conditions are never the same . The tension, diameter, movement, number of objects gripped, gripping surface, and the attachments used are just some of the factors which vary with each application . These factors, together with the effects of abrasion, corrosion, prior use or abuse and any other variables of a specific application, must be considered by the user and the grip replaced as appropriate . Where the conditions of the application are not well defined or known, or where risk of injury to persons or property is involved, a greater safety factor should be utilized . Under normal conditions, Kellems' recommended factor of safety is five for catalog listed pulling grips, and ten for catalog listed support grips. Any warranty as to quality, performance or fitness for use of grips is always premised on the condition that the published breaking strengths apply only to new, unused grips, and that such products are properly stored, handled, used, maintained and inspected by the user at a frequency appropriate for the use and condition of the grip . Examples Grip Style Approx. Breaking Strength Lbs. (N) Safety Factor Max. Rec. Load Lbs. (N) Catalog Number Pulling Grips Support Grips 27,200 (120,986) 1,610 (7,161) 5 10 5,440 (24,197) 161 (716) 03301027 02201018 The maximum recommended working load then is the tension to be exerted on the grip in application with a margin of safety to take care of unforeseen and unusual circumstances . It is the end-user's decision to determine how much of a safety factor is acceptable for the application . The metric unit of measure (force) for breaking strength and load is newtons (N) . To convert from newtons to the metric unit of weight (kilograms) the conversion factor is 9 .808 newtons/kilogram . Technical Information Pulling Grip Materials Material Galvanized steel wire Features * High strength * Not subject to continuous outside environment Non-metallic strand * Superior flex life * Non-conductive * Corrosion resistant * Moderate strength Product Group * Pulling grips * Wire rope grips * Splicing grips * Non-conductive pulling grips Approvals UL and CSA Certification is indicated on appropriate product catalog pages . T-18 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Pulling Grips Overhead Pulling DUA-PULL(R) Grips DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead transmission line stringing applications . They have a dual function of working with both bare and insulated conductors and synthetic rope, not provided by any other grip . Kellems' patented two-over, two-under weave design gives exceptional strength and gripping ability by putting more steel mesh in contact with the cable or rope surfaces . THIS IS THE ONLY PULLING GRIP RECOMMENDED FOR USE ON SYNTHETIC ROPE . Application The DUA-PULL Grips are primarily used in overhead transmission line construction where loads and safety considerations require an extra high strength grip . They are most commonly used for attaching pulling lines to conductors, conductors to running boards and "double socking" for conductor-to-conductor connections . The DUA-PULL line accommodates ACSR, ACAR, all aluminum and copper conductors . Also, the grips accommodate ground wires, messenger strands, wire ropes and synthetic ropes . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Benefits * * * * * Made of high strength galvanized steel strand. Recommended for pulling bare or insulated conductor, wire rope and synthetic rope. DUA-PULL mesh design offers the greatest holding power for all pulling applications. Each grip size is color coded for fast and accurate identification and selection. Will mate with swivels. See page T-16. Feed Tubes The Kellems Feed Tube is used when assembling synthetic rope into the DUA-PULL Grip . It is required on the largest two sizes of DUA-PULL Grips . Feed Tubes are available for use on all size DUA-PULL Grips . Benefits * Saves time, allowing fast, easy assembly. * Can be reused if not damaged. Note: 1. Do not run grips or swivels over bullwheels while under tension. 2. Two Punch-Lok (R) bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip's tail. Banding is required to ensure maximum reliability and guard against accidental release. See page T-15. 3. Double braided rope, such as 2-in-1 type, should be back spliced for approximately 2/3 of the mesh length for best gripping results. Grip size should be selected by diameter of back splice. Technical Information Dimensions in Inches (cm) www.hubbell-wiring.com T-19 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Pulling Grips Overhead Pulling Multiple Strength Grips Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare conductor, ground wires, messenger strands, wire rope and insulated cables . They are made of high strength galvanized steel strand and feature a multi-weave mesh construction of single, double and triple weave for firm holding power . Application Kellems Multiple Strength Grips are ideal for overhead transmission and distribution line stringing where moderate loading is anticipated . They are economical tools for attaching conductors to pulling lines and double socking for conductor-to-conductor connections . Rotating Eye Feature Multiple Strength Grips are available with a forged steel rotating eye which can be attached to a swivel . The forged eye is durable, compact and streamlined and will thread through blocks and sheaves without binding . The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling torque when tension is relaxed . If constant swivel action is required, a swivel should be used . For rotating eye dimensions, see page T-21 . For swivels, see page T-16 . Flexible Eye Feature Multiple Strength Grips are also available with a flexible, patented wire rope eye . This compact eye will mate with a swivel, and pass through blocks and sheaves without binding . Benefits * Economical, high strength pulling tool. * Multi-weave construction provides greater strength and holding power. * Endless Weave Grip end lies flat on the cable and will not snag. Note: 1. Do not run grips or swivels over bullwheels while under tension. Technical Information 2. Two Punch-Lok (R) bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip's tail. Banding is required to ensure maximum reliability and guard against accidental release. See page T-15. T-20 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Pulling Grips Underground Pulling K-Type and T-Type Grips K-Type Application Rotating Eye, K-Type Pulling Grips are specially designed for use in the installation of underground power cables, communication lines and service lines into factories, shopping centers, construction projects and general underground electrical construction . Rotating Eye Feature K-Type Grips come equipped with a forged steel rotating eye which can be attached to a swivel . The forged eye is durable, compact and streamlined, and will thread through blocks and sheaves without binding . The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling torque when the tension is relaxed . If constant swivel action is required, a swivel should be used . For swivels, see page T-16 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Benefits * An economical tool for pulling cable. * Safe, rugged and dependable. * Equipped with a rotating eye for spin out of pulling torque after load release . * Easily installed and removed. 3/16 R. B F C A Rotating Eye Dimensions 1/8 R. Rotating Eye Dimensions Inches (cm) A B C D F " (2 .22) 1" (2 .54) 1" (3 .49) 1" (4 .13) 1" (4 .76) " (2 .22) 1" (2 .54) 1" (3 .49) 1" (4 .13) 1" (4 .76) " ( .71) " (1 .27) " (1 .27) " (1 .59) "(1 .67) " (1 .27) " (1 .43) " (1 .75) " (2 .22) 1" (2 .54) " (2 .22) " (2 .06) 1" (2 .54) 1" (3 .02) 1" (3 .49) 2" (6 .67) 3" (8 .89) 4" (11 .43) 5" (13 .49) 6" (15 .56) D T-Type Kellems Flexible T-Type Pulling Grips are made of high strength galvanized steel strand . They feature double weave mesh for positive holding power in medium to heavy pulling jobs . The grip eye will easily attach to a swivel . Application Benefits * * * * * Will pull a single cable or cable bundles. Patented flexible eye design provides flexibility to follow line of pull. A dependable, reusable pulling tool. Easily installed and removed. Mates easily with a swivel. See page T-16. Dimensions in Inches (cm) www.hubbell-wiring.com T-21 Technical Information T-Type Pulling Grips are used for the installation of underground power cables, communication lines and service lines into factories, construction projects and for general underground electrical construction . Available in two mesh lengths, short for medium pulls, and standard for general purpose pulling . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Pulling Grips Special Purpose Grips Non-Conductive Pulling Grips Kellems Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid fiber, are available for pulling single cable or cable bundles . Their braided double weave design adds strength and positive holding power . Application Kellems Non-Conductive Pulling Grips were developed for use by utilities for pulling overhead distribution lines in close proximity to energized lines and hardware . Benefits * * * * * Color coded for fast on-site selection. Extra flexibility for easy installation. Non-metallic mesh provides for safe pulls over "hot" areas. Pellethane jacketed aramid fiber mesh resists abrasion. Grips are corrosion resistant. Note: Taping is required to guard against accidental release and to insure maximum reliability. Apply vinyl plastic electrical tape starting 2" to 3" (5.08cm to 7.62cm) from the tail of the grip onto 2" to 3" (5.08cm to 7.62cm) of cable. Slack Pulling Grips Slack Pulling Grips are offered in three styles made of galvanized steel . The closed type is used when the cable end is accessible . When not, there are split lace and split rod closing styles . All grips feature single offset eye for easy attachment to a pulling line . Application Slack Grips are widely used in pulling slack for final placement of under ground cable after it has been pulled in . They are also used for removing cable . Standard mesh lengths are generally used in restricted space for short pulls . Longer lengths are used for higher pulling loads where space is not restricted . Benefits Technical Information * Easy attachment to pulling lines. * Reusable rawhide lace for lace closure. * Galvanized steel for strength. Note: 1. Replacement rawhide lace. Catalog number 20920002. 2. See page T-44 for lace and rod closing instructions. T-22 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Pulling Grips Commercial Construction/Light Duty Grips Light Duty Pulling Grips Light Duty Pulling Grips are made of galvanized steel in a single weave construction . They feature a flexible eye for easy attachment to a pulling line . Application Light Duty Grips are used in general underground electrical construction where pulling tensions are low . They are easy tools to use in wiring industrial plants and commercial buildings . Benefits Kellems(R) Wire Management Products Kellems(R) Wire Management Products * Perfect tools for light pulling jobs. * Installs easily on cable. * Strong, galvanized steel construction. Junior Duty Pulling Grips Junior Pulling Grips feature a strong galvanized steel, single weave mesh . A flexible eye easily attaches to a pulling line, snake or fish tape . Application Designed to pull building wire, Junior grips are safe tools to use in pulling wire at low tension through conduit during electrical construction . Benefits * * * * Installs easily over building wire. Strong secure grip. Reusable. Pulls single cable or cable bundles. Junior Grip Kit Junior Grip Kit contains 6 grips, one of each size . Catalog number 033051114 . Note: See page T-27 for building wire selection chart. Technical Information Dimensions in Inches (cm) www.hubbell-wiring.com T-23 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Splicing Grips Splicing Grips Wire Rope Splicing Kellems Wire Rope Grips are made of high strength galvanized steel strand in a construction of triple, double and single weave for superior gripping ability . They are available with or without a rotating barrel which will help eliminate twist in the old rope from being transferred to the new rope . Application Wire Rope Grips are used for changing wire rope on oil derricks, large cranes, overhead cranes and drag lines . It provides a quick, safe, inexpensive temporary splice . By installing the used wire rope in one end and the new rope in the other, the new wire rope can be pulled in as the old one is pulled out . Benefits * High strength for secure pulling. * Easy installation. * Flexible to pass through sheaves and blocks. Note: 1. During installation each end of the grip should be banded and taped down securely over the rope to insure smooth passage through sheaves and to guard against accidental release. See page T-15 for end bands. 2. The rotating barrel is not a swivel and will not turn while under tension. It can turn to relieve pulling torque when tension is relaxed. Cable Splicing Splicing Grips are made of galvanized steel in double or single weave mesh construction . They are available in various lengths and sizes to suit most applications . Application Splicing Grips are used as a temporary splice for rope, cable or wire rope . They can also be used as cable reinforcement, and can act as a shield to protect cables and hoses from abrasion . Benefits * Easily installed or removed. * Galvanized steel construction for strength. * Flexible to follow cable path. Technical Information Note: 1. During installation, each end of the splicing grip should be banded and taped down securely to the cable to insure smooth passage with the cable and guard against accidental release. 2. See page T-15 for end bands. T-24 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Punch-Lok(R) Bands and Swivels Accessories Punch-Lok(R) Bands Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from being tripped or pulled loose . Also, they assure full gripping action by locking the mesh of the tail in tight contact with the cable or rope . When the tail of a grip is the leading end, the bands are particularly important to prevent accidental release caused by tripping on obstructions . A conductor-to-conductor (double-socking) pulling operation is a good example: where two grips connect two conductors to form a temporary splice . Bands should be applied to the ends of the grips as illustrated on page T-15 . It is also common practice to tape over the banded tail area to assure smooth passage through the sheaves . The conductor should be installed in the grip up to the elbows of the aluminum shoulders in order to assure full and complete gripping action . The banding procedure is then followed as illustrated on page T-15 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: In all cases two Punch-Lok Bands should be double wrapped approximately 1" to 2" (2.54cm to 5.08cm) from the grip's tail. Banding is required to ensure maximum reliability and guard against accidental release. Swivels Swivels are essential to the efficiency and safety of any high tension application . They are particularly important where continuous pulls develop higher and higher torque levels . Torque is intensified by the pullresistance of the cable itself and the resistance of the high tension controlling equipment regulating line sag . Ball bearing swivels release torque and prevent it from reaching dangerous levels that can damage the cable and obstruct the lines as it passes through sheaves, wheels or blocks . Technical Information Punch-Lok (R) is a registered trademark of Punch-Lok Inc. Dimensions in Inches (cm) www.hubbell-wiring.com T-25 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Pulling Grips Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters How to choose the correct grip size: 1 . Find the Grip Circumference Range by measuring the circumference of the bundle of different diameter cables to be gripped (see illustration) . 2 . Divide the bundle circumference by 3 .14 to determine the diameter . 3 . Choose a grip offering a range of cable diameters the same as the cable diameter . For Pulling Grips* CAUTION: When a grip is used on multiple cables, the tail end of the grip should be banded after positioning on the cables . For Cables of Equal Diameters Under "Number of Cables in One Grip", find the diameter of your single cable in vertical column . Read the grip diameter range to the right . If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips . Example: 3 cables, each with .89" (2 .26cm) diameter, for a Closed Grip select the 1 .50"-1 .74" (3 .81cm-4 .42cm) range, for a Split Grip select the 1 .75"-1 .99" (4 .44cm-5 .05cm) range . Technical Information Number of Cables in One Grip 2 3 4 5 6 and 7 8 9 Grip Dia.Range Inches (cm) .30- .38 ( .76- .97) .38- .44 ( .97-1 .12) .44- .59 (1 .12-1 .50) .59- .75 (1 .50-1 .90) .75- .90 (1 .90-2 .29) .90-1 .07 (2 .29-2 .72) 1 .07-1 .22 (2 .72-3 .10) 1 .22-1 .53 (3 .10-3 .89) 1 .53-1 .83 (3 .89-4 .65) 1 .83-2 .14 (4 .65-5 .44) 2 .14-2 .44 (5 .44-6 .20) 2 .44-2 .75 (6 .20-6 .98) 2 .75-3 .06 (6 .98-7 .77) .25- .31 ( .63- .79) .31- .36 ( .79- .91) .36- .49 ( .91-1 .24) .49- .63 (1 .24-1 .60) .63- .76 (1 .60-1 .93) .76- .89 (1 .93-2 .26) .89-1 .02 (2 .26-2 .59) 1 .02-1 .28 (2 .59-3 .25) 1 .28-1 .53 (3 .25-3 .89) 1 .53-1 .79 (3 .89-4 .55) 1 .79-2 .05 (4 .55-5 .21) 2 .05-2 .30 (5 .21-5 .84) 2 .30-2 .56 (5 .84-6 .50) .22- .27 ( .56- .69) .27- .31 ( .69- .79) .31- .42 ( .79-1 .07) .42- .54 (1 .07-1 .37) .54- .65 (1 .37-1 .65) .65- .77 (1 .65-1 .96) .77- .88 (1 .96-2 .24) .88-1 .10 (2 .24-2 .79) 1 .10-1 .32 (2 .79-3 .35) 1 .32-1 .54 (3 .35-3 .91) 1 .54-1 .76 (3 .91-4 .47) 1 .76-1 .98 (4 .47-5 .03) 1 .98-2 .20 (5 .03-5 .59) .19- .24 ( .48- .60) .24- .29 ( .61- .74) .29- .38 ( .74- .97) .38- .48 ( .97-1 .22) .48- .58 (1 .22-1 .47) .58- .67 (1 .47-1 .70) .67- .77 (1 .70-1 .96) .77- .96 (1 .96-2 .44) .96-1 .16 (2 .44-2 .95) 1 .16-1 .35 (2 .95-3 .43) 1 .35-1 .54 (3 .43-3 .91) 1 .54-1 .74 (3 .91-4 .42) 1 .74-1 .93 (4 .42-4 .90) .17- .22 ( .43- .56) .22- .26 ( .56- .66) .26- .34 ( .66- .86) .34- .43 ( .86-1 .09) .43- .52 (1 .09-1 .32) .52- .60 (1 .32-1 .52) .60- .69 (1 .52-1 .75) .69- .86 (1 .75-2 .18) .86-1 .03 (2 .18-2 .62) 1 .03-1 .20 (2 .62-3 .05) 1 .20-1 .37 (3 .05-3 .48) 1 .37-1 .55 (3 .48-3 .94) 1 .55-1 .72 (3 .94-4 .37) .15- .19 ( .38- .48) .19- .23 ( .48- .58) .23- .31 ( .58- .79) .31- .39 ( .79- .99) .39- .46 ( .99-1 .17) .46- .54 (1 .17-1 .37) .54- .62 (1 .37-1 .57) .62- .77 (1 .57-1 .96) .77- .93 (1 .96-2 .36) .93-1 .08 (2 .36-2 .74) 1 .08-1 .24 (2 .74-3 .15) 1 .24-1 .39 (3 .15-3 .53) 1 .39-1 .55 (3 .53-3 .94) .14- .18 ( .36- .46) .18- .21 ( .46- .53) .21- .28 ( .53- .71) .28- .35 ( .71- .89) .35- .42 ( .89-1 .07) .42- .49 (1 .07-1 .24) .49- .56 (1 .24-1 .42) .56- .71 (1 .42-1 .80) .71- .85 (1 .80-2 .16) .85- .99 (2 .16-2 .51) .99-1 .13 (2 .51-2 .87) 1 .13-1 .27 (2 .87-3 .23) 1 .27-1 .41 (3 .23-3 .58) .50- .61 (1 .27-1 .55) .62- .74 (1 .57-1 .88) .75- .99 (1 .90-2 .51) 1 .00-1 .24 (2 .54-3 .15) 1 .25-1 .49 (3 .17-3 .78) 1 .50-1 .74 (3 .81-4 .42) 1 .75-1 .99 (4 .44-5 .05) 2 .00-2 .49 (5 .08-6 .32) 2 .50-2 .99 (6 .35-7 .59) 3 .00-3 .49 (7 .62-8 .86) 3 .50-3 .99 (8 .89-10 .13) 4 .00-4 .49 (10 .16-11 .40) 4 .50-4 .99 (11 .43-12 .67) Note: * This chart is not to be used for Conduit Riser Grips. Refer to the chart for Conduit Riser multiple cable section. It is always recommended that, when multiple cables are installed in a pulling grip, the tail end be banded and tightly taped after installation on the cable bundle. See page T-15 for end bands. T-26 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Junior Pulling Grips Junior Pulling Grip Selection Chart These charts are a general guide to assist in the selection of the correct Junior Pulling Grip for pulling various groupings of building wire . It is not intended to be restrictive inasmuch as the use of "dummy" wires (short pieces of wire used to fill out the Grip) or the tight taping of the wires into a compact bundle may increase or decrease the number of wires per Grip . T.H.W.N., T.H.H.N. and X.H.H.W. Building Wire #14 #12 #10 #8 #6 #4 #3 #2 #1 #1/0 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 37 Strand 37 Strand Cable Diameter Range Desc. In. (cm) Approx. Breaking Strength Lbs. (N) Approximate Number Of Wires In One Grip J 25 .25- .36 ( .63- .91) J 37 .37- .49 ( .94-1 .24) J 50 .50- .61 (1 .27-1 .55) J 62 .62- .74 (1 .57-1 .88) J 75 .75- .99 (1 .90-2 .51) J 100 1 .00-1 .24 (2 .54-3 .15) 450 (2,002) 900 (4,003) 1,300 (5,782) 1,950 (8,674) 2,800 (12,454) 3,900 (17,347) Catalog Number 4-8 3-6 2-3 2 1 1 1 -- -- -- 03305001 9-16 6-11 4-6 3 2 -- -- 1 1 1 03305002 16-25 11-17 7-10 4-5 3-4 2 2 -- -- -- 03305003 26-37 18-25 11-14 6-8 5-6 3 3 2 2 -- 03305004 37-66 26-47 15-27 9-16 6-11 4-7 4-5 3-4 3 2-3 03305005 66-104 47-74 28-43 16-24 11-17 8-10 6-8 5-7 4-5 4 03305006 #6 7 Strand #4 7 Strand #2 7 Strand #1 #1/0 19 Strand 19 Strand Kellems(R) Wire Management Products Kellems(R) Wire Management Products R.H.H., R.H., R.W. and R.H.W. Building Wire #14 7 Strand #12 7 Strand #10 7 Strand #8 7 Strand Cable Diameter Range Desc. In. (cm) Approx. Breaking Strength Lbs. (N) Approximate Number Of Wires In One Grip J 25 .25- .36 ( .63- .91) J 37 .37- .49 ( .94-1 .24) J 50 .50- .61 (1 .27-1 .55) J 62 .62- .74 (1 .57-1 .88) J 75 .75- .99 (1 .90-2 .51) J 100 1 .00-1 .24 (2 .54-3 .15) 450 (2,002) 900 (4,003) 1,300 (5,782) 1,950 (8,674) 2,800 (12,454) 3,900 (17,347) Catalog Number 2 2 1 1 -- -- -- -- -- 03305001 3 2-3 2 -- 1 1 1 -- -- 03305002 4-5 4-5 3-4 2 -- -- -- 1 -- 03305003 6-8 6-7 4-5 3 2 2 -- -- 1 03305004 9-16 8-14 6-10 4-6 3-4 3-4 2-3 2 -- 03305005 16-24 15-22 11-16 7-10 5-7 4-6 4 3 2-3 03305006 #14 7 Strand #12 7 Strand #10 7 Strand #8 7 Strand #6 7 Strand #4 7 Strand #2 7 Strand #1 7 Strand #1/0 19 Strand T.H.W. Building Wire Approx. Breaking Strength Lbs. (N) Approximate Number Of Wires In One Grip J 25 .25- .36 ( .63- .91) J 37 .37- .49 ( .94-1 .24) J 50 .50- .61 (1 .27-1 .55) J 62 .62- .74 (1 .57-1 .88) J 75 .75- .99 (1 .90-2 .51) J 100 1 .00-1 .24 (2 .54-3 .15) 450 (2,002) 900 (4,003) 1,300 (5,782) 1,950 (8,674) 2,800 (12,454) 3,900 (17,347) Dimensions in Inches (cm) Catalog Number 2-4 2-3 2 1 1 1 -- -- -- 03305001 5-7 4-5 3-4 2 -- -- 1 -- -- 03305002 8-11 6-8 5-7 3-4 2 2 -- 1 1 03305003 12-16 9-12 8-10 5-6 3-4 3 2 -- -- 03305004 17-30 13-24 11-19 7-10 5-7 4-5 3-4 2 2 03305005 31-48 25-37 20-30 11-17 8-11 6-8 5-6 3-4 3 03305006 www.hubbell-wiring.com T-27 Technical Information Cable Diameter Range Desc. In. (cm) Support Grips - Heavy Duty, Standard Duty, Light Duty Support Grips - Heavy Duty, Standard Duty, Light Duty Kellems(R) Wire Management Products Kellems(R) Wire Management Products T-28 www.hubbell-wiring.com Kellems(R) Wire Management Products Kellems(R) Wire Management Products Support Grips - Heavy Duty, Standard Duty, Light Duty Tin-Coated Bronze/Stainless Steel Solid eye assemblies provide eye reinforcement at support hardware Four eye styles available: single (shown), double, universal, and offset Identification tag shows: catalog number, diameter range, agency approval, and bar code Support Grips - Heavy Duty, Standard Duty, Light Duty The strand equalizer positions wires for equal loading throughout the entire grip length The positive action mesh grip is designed for light duty up to heavy duty . Closed grips fit over the cable end, split grips wrap around the cable mid-span . The standard material is nonmagnetic, tin-coated bronze . Selected items are available in stainless steel . For exceptional immunity to rust and corrosion with superior strength and flexibility for heavy duty support application in harsh environments; contact the factory The endless weave provides easy installation onto cable and can be easily repositioned Dimensions in Inches (cm) www.hubbell-wiring.com T-29 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Standard Duty Support Grips Single Eye, Single Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Single Eye, Closed Mesh* For permanent support when cable end is available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 530 (2,357) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 4,900 (21,795) 4,900 (21,795) 7" (17 .78) 8" (20 .32) 8" (20 .32) 9" (22 .86) 10" (25 .40) 12" (30 .48) 14" (35 .56) 16" (40 .64) 18" (45 .72) 21" (53 .34) 24" (60 .96) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 02201013 02201014 02201015 02201017 02201018 02201019 02201020 02201021 02201022 02201023 02201024 Single Eye, Split Mesh, Lace Closing* For permanent support when cable end is not available . Single Eye, Closed Mesh Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 530 (2,357) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 4,900 (21,795) 4,900 (21,795) 7" (17 .78) 8" (20 .32) 8" (20 .32) 9" (22 .86) 10" (25 .40) 12" (30 .48) 14" (35 .56) 16" (40 .64) 18" (45 .72) 21" (53 .34) 24" (60 .96) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 02202013 02202014 02202015 02202017 02202018 02202019 02202020 02202021 02202022 02202023 02202024 Single Eye, Split Mesh, Rod Closing* Standard Duty Support Grips Single Eye, Split Mesh, Lace Closing Single Eye, Split Mesh, Rod Closing T-30 For support when cable end is not available . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 790 (3,514) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 5,750 (25,576) 5,750 (25,576) 7" (17 .78) 8" (20 .32) 8" (20 .32) 9" (22 .86) 10" (25 .40) 12" (30 .48) 14" (35 .56) 16" (40 .64) 18" (45 .72) 21" (53 .34) 24" (60 .96) 8 .5" (21 .59) 8 .5" (21 .59) 10 .5" (26 .67) 12 .5" (31 .75) 14 .5" (36 .83) 15 .5" (39 .37) 16 .5" (41 .91) 19 .5" (49 .53) 21 .5" (54 .61) 23 .5" (59 .69) 25 .5" (64 .77) 02203013 02203014 02203015 02203017 02203018 02203019 02203020 02203021 02203022 02203023 02203024 Note: E-Eye length. M-Mesh length at nominal diameter. * Change catalog number from 022 to 024 for stainless steel. Consult factory for availability. www.hubbell-wiring.com Dimensions in Inches (cm) Standard Duty Support Grips Double Eye, Single Weave, Tin-Coated Bronze Double Eye, Closed Mesh* For permanent support when cable end is available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 530 (2,357) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 4,900 (21,795) 4,900 (21,795) 4" (10 .16) 4" (10 .16) 4" (10 .16) 5" (12 .70) 5" (12 .70) 5" (12 .70) 6" (15 .24) 6" (15 .24) 6" (15 .24) 8" (20 .32) 8" (20 .32) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 02201001 02201002 02201003 02201005 02201006 02201007 02201008 02201009 02201010 02201011 02201012 WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Double Eye, Split Mesh, Lace Closing* For permanent support when cable end is not available . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 530 (2,357) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 4,900 (21,795) 4,900 (21,795) 4" (10 .16) 4" (10 .16) 4" (10 .16) 5" (12 .70) 5" (12 .70) 5" (12 .70) 6" (15 .24) 6" (15 .24) 6" (15 .24) 8" (20 .32) 8" (20 .32) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 02202001 02202002 02202003 02202005 02202006 02202007 02202008 02202009 02202010 02202011 02202012 Double Eye, Closed Mesh Double Eye, Split Mesh, Rod Closing* For support when cable end is not available . Double Eye, Split Mesh, Lace Closing Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 790 (3,514) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 5,750 (25,576) 5,750 (25,576) 4" (10 .16) 4" (10 .16) 4" (10 .16) 5" (12 .70) 5" (12 .70) 5" (12 .70) 6" (15 .24) 6" (15 .24) 6" (15 .24) 8" (20 .32) 8" (20 .32) 8.5" (21 .59) 8 .5" (21 .59) 10 .5" (26 .67) 12 .5" (31 .75) 14 .5" (36 .83) 15 .5" (39 .37) 16 .5" (41 .91) 19 .5" (49 .53) 21 .5" (54 .61) 23 .5" (59 .69) 25 .5" (64 .77) 02203001 02203002 02203003 02203005 02203006 02203007 02203008 02203009 02203010 02203011 02203012 Note: E-Eye length. M-Mesh length at nominal diameter. * Change catalog number from 022 to 024 for stainless steel. Consult factory for availability. Dimensions in Inches (cm) www.hubbell-wiring.com Double Eye, Split Mesh, Rod Closing T-31 Standard Duty Support Grips Cable Diameter Range Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Standard Duty Support Grips Offset Eye, Single Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Offset Eye, Closed Mesh* For permanent support when cable end is available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 500 (2,224) 750 (3,336) 950 (4,226) 1,500 (6,672) 1,500 (6,672) 1,500 (6,672) 2,000 (8,896) 3,100 (13,789) 3,100 (13,789) 3,800 (16,902) 3,250 (14,480) 4" (10 .16) 4" (10 .16) 4" (10 .16) 5" (12 .70) 5" (12 .70) 5" (12 .70) 6" (15 .24) 9" (22 .86) 9" (22 .86) 11" (27 .94) 11" (27 .94) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 02201037 02201038 02201039 02201041 02201042 02201043 02201044 02201045 02201046 02201047 02201048 Offset Eye, Split Mesh, Lace Closing* For permanent support when cable end is not available . Offset Eye, Closed Mesh Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 500 (2,224) 750 (3,336) 950 (4,226) 1,500 (6,672) 1,500 (6,672) 1,500 (6,672) 1,800 (8,006) 2,150 (9,563) 2,150 (9,563) 3,250 (14,480) 3,250 (14,480) 4" (10 .16) 4" (10 .16) 4" (10 .16) 5" (12 .70) 5" (12 .70) 5" (12 .70) 6" (15 .24) 9" (22 .86) 9" (22 .86) 11" (27 .94) 11" (27 .94) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 25" (63 .50) 27" (68 .58) 02202037 02202038 02202039 02202041 02202042 02202043 02202044 02202045 02202046 02202047 02202048 Offset Eye, Split Mesh, Rod Closing* Standard Duty Support Grips Offset Eye, Split Mesh, Lace Closing Offset Eye, Split Mesh, Rod Closing T-32 For support when cable end is not available . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 500 (2,224) 750 (3,336) 950 (4,226) 1,500 (6,672) 1,500 (6,672) 1,500 (6,672) 2,000 (8,896) 3,100 (13,789) 3,100 (13,789) 4,300 (19,126) 4,900 (21,795) 4" (10 .16) 4" (10 .16) 4" (10 .16) 5" (12 .70) 5" (12 .70) 5" (12 .70) 6" (15 .24) 9" (22 .86) 9" (22 .86) 11" (27 .94) 11" (27 .94) 7" (17 .78) 9" (22 .86) 10" (25 .40) 12" (30 .48) 14" (35 .56) 15" (38 .10) 16" (40 .64) 19" (48 .26) 20" (50 .80) 21" (53 .34) 21" (53 .34) 02203037 02203038 02203039 02203041 02203042 02203043 02203044 02203045 02203046 02203047 02203048 Note: E-Eye length. M-Mesh length at nominal diameter. * Change catalog number from 022 to 024 for stainless steel. Consult factory for availability. www.hubbell-wiring.com Dimensions in Inches (cm) Standard Duty Support Grips Universal Eye, Single Weave, Tin-Coated Bronze Universal Eye, Closed Mesh* For permanent support when cable end is available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 530 (2,357) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 02201051 02201052 02201053 02201050 02201054 02201055 02201056 02201057 02201058 WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Universal Eye, Split Mesh, Lace Closing For permanent support when cable end is not available . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .50"-3 .99" (8 .89-10 .13) 530 (2,357) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 4,900 (21,795) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 10" (25 .40) 10" (25 .40) 13" (33 .02) 14" (35 .56) 15" (38 .10) 17" (43 .18) 19" (48 .26) 21" (53 .34) 23" (58 .42) 27" (68 .58) 02202050 02202051 02202052 02202054 02202055 02202056 02202057 02202058 02202059 02202061 Universal Eye, Closed Mesh Universal Eye, Split Mesh, Rod Closing* For support when cable end is not available . Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .50"- .62" (1 .27-1 .57) .63"- .74" (1 .60-1 .88) .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .74" (3 .81-4 .42) 1 .75"-1 .99" (4 .44-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 790 (3,514) 790 (3,514) 1,020 (4,537) 1,610 (7,161) 1,610 (7,161) 1,610 (7,161) 2,150 (9,563) 3,260 (14,500) 3,260 (14,500) 5,750 (25,576) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 18" (45 .72) 8 .5" (21 .59) 8 .5" (21 .59) 10 .5" (26 .67) 12 .5" (31 .75) 14 .5" (36 .83) 15 .5" (39 .37) 16 .5" (41 .91) 19 .5" (49 .53) 21 .5" (54 .61) 23 .5" (59 .69) 02203064 02203065 02203066 02203068 02203069 02203070 02203071 02203072 02203073 02203074 Universal Eye, Split Mesh, Lace Closing Note: E-Eye length. M-Mesh length at nominal diameter. * Change catalog number from 022 to 024 for stainless steel. Consult factory for availability. Universal Eye, Split Mesh, Rod Closing Dimensions in Inches (cm) www.hubbell-wiring.com T-33 Standard Duty Support Grips Cable Diameter Range Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Heavy Duty Support Grips Single Eye, Double Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Heavy Duty, Single Eye, Closed Mesh* For heavy duty permanent support when cable end is available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2,820 (12,543) 4,280 (19,037) 4,280 (19,037) 4,280 (19,037) 10" (25 .40) 12" (30 .48) 12" (30 .48) 12" (30 .48) 25" (63 .50) 28" (71 .12) 30" (76 .20) 34" (86 .36) 02206010 02206011 02206012 02206013 Heavy Duty, Single Eye, Closed Mesh Single Eye, Split Mesh, Lace Closing* For permanent support when cable end is not available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2,820 (12,543) 4,280 (19,037) 4,280 (19,037) 4,280 (19,037) 10" (25 .40) 12" (30 .48) 12" (30 .48) 12" (30 .48) 25" (63 .50) 28" (71 .12) 30" (76 .20) 34" (86 .36) 02207010 02207011 02207012 02207013 Note: E-Eye length. M-Mesh length at nominal diameter. * Change catalog number from 022 to 024 for stainless steel. Consult factory for availability. Heavy Duty Support Grips Single Eye, Split Mesh, Lace Closing T-34 www.hubbell-wiring.com Dimensions in Inches (cm) Heavy Duty Support Grips Double Eye, Double Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Double Eye, Closed Mesh* For permanent support when cable end is available to be installed through grip . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .75"- .99"(1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 4 .00"-4 .49" (10 .16-11 .40) 4 .50"-4 .99" (11 .43-12 .67) 2,820 (12,543) 4,280 (19,037) 4,280 (19,037) 4,280 (19,037) 8,050 (35,806) 8,050 (35,806) 10,060 (44,747) 12,070 (53,687) 12,070 (53,687) 12,070 (53,687) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 12" (30 .48) 12" (30 .48) 12" (30 .48) 12" (30 .48) 12" (30 .48) 12" (30 .48) 25" (63 .50) 28" (71 .12) 30" (76 .20) 34" (86 .36) 36" (91 .44) 38" (96 .52) 40" (101 .60) 44" (111 .76) 46" (116 .84) 68" (172 .72) 02206001 02206002 02206003 02206004 02206005 02206006 02206007 02206008 02206009 02208009 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Double Eye, Closed Mesh Double Eye, Split Mesh, Lace Closing* For support when cable end is not available . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .75"- .99" (1 .90-2 .51) 1 .00"-1 .24" (2 .54-3 .15) 1 .25"-1 .49" (3 .17-3 .78) 1 .50"-1 .99" (3 .81-5 .05) 2 .00"-2 .49" (5 .08-6 .32) 2 .50"-2 .99" (6 .35-7 .59) 3 .00"-3 .49" (7 .62-8 .86) 3 .50"-3 .99" (8 .89-10 .13) 4 .00"-4 .49" (10 .16-11 .40) 4 .50"-4 .99" (11 .43-12 .67) 2,820 (12,543) 4,280 (19,037) 4,280 (19,037) 4,280 (19,037) 8,050 (35,806) 8,050 (35,806) 10,060 (44,747) 12,070 (53,687) 12,070 (53,687) 12,070 (53,687) 10" (25 .40) 10" (25 .40) 10" (25 .40) 10" (25 .40) 12" (30 .48) 12" (30 .48) 12" (30 .48) 12" (30 .48) 12" (30 .48) 12" (30 .48) 25" (63 .50) 28" (71 .12) 30" (76 .20) 34" (86 .36) 36" (91 .44) 38" (96 .52) 40" (101 .60) 44" (111 .76) 46" (116 .84) 68" (172 .72) 02207001 02207002 02207003 02207004 02207005 02207006 02207007 02207008 02207009 02209009 Double Eye, Split Mesh, Lace Closing Dimensions in Inches (cm) www.hubbell-wiring.com Heavy Duty Support Grips Note: E-Eye length. M-Mesh length at nominal diameter. * Change catalog number from 022 to 024 for stainless steel. Consult factory for availability. T-35 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Service Drop Grips Single Eye, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Light Duty, Single Eye, Closed Mesh, Single Weave Light Duty, Single Eye, Closed Mesh, Single Weave Heavy Duty, Single Eye, Closed Mesh, Multi-Weave Heavy Duty, Single Eye, Closed Mesh, Multi-Weave For permanent support when cable end is available to be installed . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .23"- .31" ( .58- .79) .29"- .37" ( .74- .94) .35"- .44" ( .89-1 .12) .41"- .50" (1 .04-1 .27) .46"- .56" (1 .17-1 .42) .52"- .62" (1 .32-1 .57) .58"- .68" (1 .47-1 .73) .64"- .75" (1 .63-1 .90) .70"- .81" (1 .78-2 .06) .75"- .87" (1 .90-2 .21) .81"- .94" (2 .06-2 .39) .87"-1 .00" (2 .21-2 .54) .94"-1 .06" (2 .39-2 .69) 1 .00"-1 .18" (2 .54-3 .00) 1 .06"-1 .25" (2 .69-3 .17) 290 (1,290) 290 (1,290) 500 (2,224) 500 (2,224) 660 (2,936) 790 (3,514) 790 (3,514) 790 (3,514) 790 (3,514) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 3" (7 .62) 5" (12 .70) 5 .5" (13 .97) 5 .5" (13 .97) 6" (15 .24) 7" (17 .78) 7" (17 .78) 7" (17 .78) 7" (17 .78) 8" (20 .32) 8" (20 .32) 8" (20 .32) 9" (22 .86) 9" (22 .86) 9" (22 .86) 3 .75" (9 .52) 4 .25" (10 .79) 4 .75" (12 .06) 5" (12 .70) 5 .25" (13 .33) 6 .25" (15 .87) 6" (16 .51) 6 .75" (17 .14) 7 .25" (18 .41) 8" (20 .32) 8 .25" (20 .95) 8 .75" (22 .22) 9" (22 .86) 9 .5" (24 .13) 9 .5" (24 .13) 02216001 02216002 02216003 02216004 02216005 02216006 02216007 02216008 02216009 02216010 02216011 02216012 02216013 02216014 02216015 For permanent support when cable end is available to be installed . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .23"- .31" ( .58- .79) .29"- .37" ( .74- .94) .35"- .44" ( .89-1 .12) .41"- .50" (1 .04-1 .27) .46"- .56" (1 .17-1 .42) .52"- .62" (1 .32-1 .57) .58"- .68" (1 .47-1 .73) .64"- .75" (1 .63-1 .90) .70"- .81" (1 .78-2 .06) .75"- .87" (1 .90-2 .21) .81"- .94" (2 .06-2 .39) .87"-1 .00" (2 .21-2 .54) .94"-1 .06" (2 .39-2 .69) 1 .00"-1 .18" (2 .54-3 .00) 1 .06"-1 .25" (2 .69-3 .17) 500 (2,224) 500 (2,224) 870 (3,870) 870 (3,870) 1,050 (4,670) 1,050 (4,670) 1,050 (4,670) 1,390 (6,183) 1,390 (6,183) 1,390 (6,183) 1,390 (6,183) 1,790 (7,962) 1,790 (7,962) 1,790 (7,962) 1,790 (7,962) 5" (12 .70) 5" (12 .70) 6" (15 .24) 6" (15 .24) 6" (15 .24) 7" (17 .78) 7" (17 .78) 7" (17 .78) 8" (20 .32) 8" (20 .32) 8" (20 .32) 8" (20 .32) 9" (22 .86) 9" (22 .86) 9" (22 .86) 4 .5" (11 .43) 5 .5" (13 .97) 6 .5" (16 .51) 7 .5" (19 .05) 8" (20 .32) 8 .5" (21 .59) 9 .5" (24 .13) 9 .5" (24 .13) 10 .5" (26 .67) 10 .5" (26 .67) 10 .5" (26 .67) 11 .5" (29 .21) 12 .5" (31 .75) 13 .5" (34 .29) 14 .5" (36 .83) 02217001 02217002 02217003 02217004 02217005 02217006 02217007 02217008 02217009 02217010 02217011 02217012 02217013 02217014 02217015 Note: E-Eye length. M-Mesh length at nominal diameter. Service Drop Grips .250'' (.64) .3125'' (.80) Dia. 2.000'' (5.08) Screw Hook Catalog Number 20303001 Yield Strength 900 lbs (4003 N) T-36 www.hubbell-wiring.com 4.875'' (12.38) Dimensions in Inches (cm) Service Drop Grips Universal Eye, Tin-Coated Bronze Light Duty, Universal Eye, Closed Mesh, Single Weave For permanent support when cable end is available to be installed . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .23"- .31" ( .58- .79) .29"- .37" ( .74- .94) .35"- .44" ( .89-1 .12) .41"- .50" (1 .04-1 .27) .46"- .56" (1 .17-1 .42) .52"- .62" (1 .32-1 .57) .58"- .68" (1 .47-1 .73) .64"- .75" (1 .63-1 .90) .70"- .81" (1 .78-2 .06) .75"- .87" (1 .90-2 .21) .81"- .94" (2 .06-2 .39) .87"-1 .00" (2 .21-2 .54) .94"-1 .06" (2 .39-2 .69) 1 .00"-1 .18" (2 .54-3 .00) 1 .06"-1 .25" (2 .69-3 .17) 290 (1,290) 290 (1,290) 500 (2,224) 500 (2,224) 660 (2,936) 790 (3,514) 790 (3,514) 790 (3,514) 790 (3,514) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 1,020 (4,537) 9" (22 .86) 10" (25 .40) 10" (25 .40) 11" (27 .94) 12" (30 .48) 13" (33 .02) 13" (33 .02) 13" (33 .02) 13" (33 .02) 14" (35 .56) 14" (35 .56) 14" (35 .56) 15" (38 .10) 15" (38 .10) 15" (38 .10) 3 .75" (9 .52) 4 .25" (10 .79) 4 .75" (12 .06) 5" (12 .70) 5 .25" (13 .33) 6 .25" (15 .87) 6 .5" (16 .51) 6 .75" (17 .14) 7 .25" (18 .41) 8" (20 .32) 8 .25" (20 .95) 8 .75" (22 .22) 9" (22 .86) 9 .5" (24 .13) 9 .5" (24 .13) 02216016 02216017 02216018 02216019 02216020 02216021 02216022 02216023 02216024 02216025 02216026 02216027 02216028 02216029 02216030 Heavy Duty, Universal Eye, Closed Mesh, Multi-Weave WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Light Duty, Universal Eye, Closed Mesh, Single Weave For permanent support when cable end is available to be installed . Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .23"- .31" ( .58- .79) .28"- .37" ( .74- .94) .35"- .44" ( .89-1 .12) .41"- .50" (1 .04-1 .27) .46"- .56" (1 .17-1 .42) .52"- .62" (1 .32-1 .57) .58"- .68" (1 .47-1 .73) .64"- .75" (1 .63-1 .90) .70"- .81" (1 .78-2 .06) .75"- .87" (1 .90-2 .21) .81"- .94" (2 .06-2 .39) .87"-1 .00" (2 .21-2 .54) .94"-1 .06" (2 .39-2 .69) 1 .00"-1 .18" (2 .54-3 .00) 1 .06"-1 .25" (2 .69-3 .17) 500 (2,224) 500 (2,224) 870 (3,870) 870 (3,870) 1,050 (4,670) 1,050 (4,670) 1,050 (4,670) 1,390 (6,183) 1,390 (6,183) 1,390 (6,183) 1,390 (6,183) 1,790 (7,962) 1,790 (7,962) 1,790 (7,962) 1,790 (7,962) 11" (27 .94) 11" (27 .94) 12" (30 .48) 12" (30 .48) 12" (30 .48) 13" (33 .02) 13" (33 .02) 13" (33 .02) 14" (35 .56) 14" (35 .56) 14" (35 .56) 14" (35 .56) 15" (38 .10) 15" (38 .10) 15" (38 .10) 4 .5" (11 .43) 5 .5" (13 .97) 6 .5" (16 .51) 7 .5" (19 .05) 8" (20 .32) 8 .5" (21 .59) 9 .5" (24 .13) 9 .5" (24 .13) 10 .5" (26 .67) 10 .5" (26 .67) 10 .5" (26 .67) 11 .5" (29 .21) 12 .5" (31 .75) 13 .5" (34 .29) 14 .5" (36 .83) 02217016 02217017 02217018 02217019 02217020 02217021 02217022 02217023 02217024 02217025 02217026 02217027 02217028 02217029 02217030 Heavy Duty, Universal Eye, Closed Mesh, Multi-Weave Note: E-Eye length. M-Mesh length at nominal diameter. Service Drop Grips Dimensions in Inches (cm) www.hubbell-wiring.com T-37 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Bus Drop Support Grips Single Eye, Universal Eye, Galvanized Steel WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-46 . Safety Spring Maximum Deflection Inches/Lbs (cm/N) Approx. Breaking Strength Lbs. (N) Length* Inches (cm) Diameter Inches (cm) Model Lbs. (N) Catalog Number 23/4" at 40 lbs. (6.98 cm at 178 N) 3" at 80 lbs. (7.94 cm at 356 N) 500 (2,224) 850 (3,781) 8.25" (20.95) 8.25" (20.95) .75" (1.90) 1" (2.54) 40 lb. spring (178) 80 lb. spring (356) 20302001 20302002 Note: Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye and replacing drawbar. * No load. Safety Spring Single Eye, Wide Range Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .24"-.32" (.61-.81) .32"-.43" (.81-1.09) .43"-.56" (1.09-1.42) .56"-.73" (1.42-1.85) .73"-.85" (1.85-2.16) .85"-1.00" (2.16-2.54) 1.00"-1.25" (2.54-3.17) 350 (1,557) 450 (2,002) 550 (2,446) 1,000 (4,448) 1,400 (6,227) 1,400 (6,227) 1,500 (6,672) 3" (7.62) 4" (10.16) 6" (15.24) 7" (17.78) 7" (17.78) 8" (20.32) 9" (22.86) 3.5" (8.89) 4" (10.16) 4.75" (12.06) 6" (15.24) 6.75" (17.14) 8" (20.32) 9.5" (24.13) 073041276** 073041277 073041278 073041279 073041280 073041281 073041282 Universal Eye, Wide Range Single Eye, Wide Range Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Inches (cm) M Inches (cm) Catalog Number .32"-.43" (.81-1.09) .43"-.56" (1.09-1.42) .56"-.73" (1.42-1.85) .73"-.85" (1.85-2.16) .85"-1.00" (2.16-2.54) 1.00"-1.25" (2.54-3.17) 450 (2,002) 550 (2,446) 1,000 (4,448) 1,400 (6,227) 1,400 (6,227) 1,500 (6,672) 10" (25.40) 12" (30.48) 13" (33.02) 13" (33.02) 14" (35.56) 15" (38.10) 4" (10.16) 4.75" (12.06) 6" (15.24) 6.75" (17.14) 8" (20.32) 9.5" (24.13) 073041284 073041285 073041286 073041287 073041288 073041289 Note: E-Eye length. M-Mesh length at nominal diameter. ** Item indicated is not UL listed. Bus Drop Grips and Safety Springs Bus Drop Support Grips Universal Eye, Wide Range Kellems Bus Drop Grips are offered with either a single eye or universal bale attachment . The mesh is single weave galvanized steel with the patented wide range construction . They are suitable for indoor use only . Consult Technical Service for Stainless Steel Grips . Application Safety Spring Bus Drop Grips provide a safe, easy and economical method to support flexible cord or bus drop cable at bus duct and other industrial areas . Benefits Strain Relief Grip * Easily installed. * Absorb tension, vibration and pull with no cable damage. * Patented mesh construction. Bus Drop Grips Strain Relief Grip Safety Spring Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye and replacing drawbar . Motor Box T-38 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Wire Management Products Conduit Riser Grips Ring Type, Single Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-47 and T-48 . Single Weave, Closed Mesh Kellems(R) Conduit Riser Support Grips are available in closed mesh and in split mesh with lace or rod closures, to cover all applications including single cable or multiple wire support . Refer to technical section, T-47 for grip selection assistance for cable bundles . The standard material is tincoated bronze strand . The grip is permanently fastened to a support ring, resulting in a one piece unit which will allow air ventilation within the conduit . The ring will fit standard electrical rigid metal conduit and schedule 40 rigid PVC conduit only . See page T-48 for ring dimensions . For permanent support when cable end is available to be installed through the grip . Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only Cable Sizes .50"- .62" .63"-.74" .75"- .99" Inches (cm) (1.27-1.57) (1.60-1-88) (1.90-2.51) Model R050 Length Inches (cm) 8" (20.32) Conduit Sizes Inches 1.00"- 1.24" 1.25"- 1.49" 1.50"-1.74" (2.54-3.15) (3.17-3.78) (3.81-4.42) 1.75"-1.99" (4.44-5.05) 2.00"- 2.49" (5.08-6.32) 2.50" -2.99" (6.35-7.59) 3.00"- 3.49" (7.62-8.86) 3.50"- 3.99" (8.89-10.13) R062 R075 R100 R125 R150 R175 R200 R250 R300 R350 9" (22.86) 11" (27.94) 12" (30.48) 12" (30.48) 14" (35.56) 15" (38.10) 17" (43.18) 18" (45.72) 20" (50.80) 21" (53.34) Catalog Number Approx. Breaking Strength Lbs. (N) 02211106 -- 530 (2,357) -- -- -- -- -- -- -- -- -- 1 02211100 02211101 -- 490 (2,179) 790 (3,514) -- -- -- -- -- -- -- -- 11/4 02211001 02211002 02211003 -- 450 (2,002) 740 (3,292) 1,030 (4,581) -- -- -- -- -- -- -- 11/2 -- 02211006 02211007 02211009 -- 690 (3,069) 970 (4,315) 1,610 (7,161) -- -- -- -- -- -- 2 -- 02211107 02211010 02211012 02211013 -- 640 (2,847) 920 (4,092) 1,520 (6,761) 1,610 (7,161) -- -- -- -- -- 21/2 -- -- -- -- 02211017 02211018 02211019 -- 1,510 (6,716) 1,610 (7,161) 2,150 (9,563) -- -- -- 3 -- -- -- 02211022 02211023 02211024 02211025 02211026 1,340 (5,960) 1,400 (6,227) 1,490 (6,627) 1,990 (8,851) 3,260 (14,500) -- -- -- 31/2 -- -- -- -- -- -- -- 02211034 -- 3,260 (14,500) -- 4 -- -- -- -- -- -- 02211040 02211041 1,670 (7,248) 2,680 (11,921) 02211042 02211043 -- 2,890 (12,855) 4,080 (18,148) 5 -- -- -- -- -- -- -- -- 02211061 2,150 (9,563) 02211062 02211063 2,860 (12,721) 3,130 (13,922) 6 -- -- -- -- -- -- -- -- -- 02211072 2,245 (9,986) 02211033 2,970 (13,211) 02211073 2,245 (9,986) Note: See page T-47 for multiple cables in a single conduit riser grip. Dimensions in Inches (cm) www.hubbell-wiring.com T-39 Conduit Riser Grips 3/4 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Conduit Riser Grips Ring Type, Double Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-47 and T-48 . Double Weave, Split Mesh, Lace Closing Kellems(R) Conduit Riser Support Grips will support cable runs in vertical or sloping standard rigid conduit . The grip is fastened to a support ring which seats on the rim of the conduit . The entire grip is supported by the conduit itself and no other hardware is required . See page T-48 for ring dimensions . The rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal conduit only . For permanent support when cable end is not available . Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only Cable Sizes Inches (cm) Model Conduit Riser Grips Length Inches (cm) .75"- .99" (1 .90-2 .51) RS075 11" (27 .94) 1 .00"- 1 .24" (2 .54-3 .15) RS100 12" (30 .48) 1 .25"- 1 .49" (3 .17-3 .78) RS125 12" (30 .48) 1 .50"-1 .74" (3 .81-4 .42) RS150 14" (35 .56) 1 .75"- 1 .99" (4 .44-5 .05) RS175 15" (38 .10) 2 .00"- 2 .49" (5 .08-6 .32) RS200 17" (43 .18) 2 .50"- 2 .99" (6 .35-7 .59) RS250 18" (45 .72) 3 .00"- 3 .49" (7 .62-8 .86) RS300 20" (50 .80) 3 .50" -3 .99" (8 .89-10 .13) RS350 21" (53 .34) Conduit Sizes Inches Catalog Number Approx. Breaking Strength Lbs. (N) 11/4 02212003 1,580 (7,028) -- -- -- -- -- -- -- -- 11/2 02212007 1,500 (6,672) -- -- -- -- -- -- -- -- 2 02212010 02212012 02212013 1,430 (6,361) 1,930 (8,585) 2,040 (9,074) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 21/2 -- -- 02212017 02212018 1,910 (8,496) 2,040 (9,074) 3 -- -- 02212023 02212024 02212025 02212026 1,780 (7,917) 1,890 (8,407) 2,520 (11,209) 4,300 (19,126) 31/2 -- -- -- -- 4 -- -- -- -- 5 -- -- -- -- -- -- 6 -- -- -- -- -- -- -- 02212040 2,110 (9,385) 02212033 02212034 3,910 (17,392) 4,300 (19,126) 02212041 02212042 02212043 3,530 (15,701) 3,820 (16,991) 5,380 (23,930) 02212061 2,860 (12,721) -- -- -- -- -- 02212073 2,955 (13,144) Note: See page T-47 for multiple cables in a single conduit riser grip. T-40 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Conduit Riser Grips Ring Type, Single Weave, Tin-Coated Bronze WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-47 and T-48 . Single Weave, Split Mesh, Rod Closing Benefits * Easy and fast to install. * Will not damage electrical cable. * Allows cable to expand or contract. * Ideal way to hold cable in vertical conduit. * Prevents cable creep in conduit. * Helps prevent cable pullouts. * The rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal conduit only . * For support when cable end is not available. Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only Model .75"- .99" (1 .90-2 .51) RR075 1 .00"- 1 .24" 1 .25"- 1 .49" 1 .50"- 1 .74" 1 .75"-1 .99" (2 .54-3 .15) (3 .17-3 .78) (3 .81-4 .42) (4 .44-5 .05) RR100 RR125 RR150 RR175 2 .00"- 2 .49" (5 .08-6 .32) RR200 2 .50"- 2 .99" (6 .35-7 .59) RR250 3 .00"-3 .49" 3 .50"-3 .99" (7 .62-8 .86) (8 .89-10 .13) RR300 RR350 Length Inches (cm) 11" (27 .94) 12" (30 .48) 16" (40 .64) 18" (45 .72) 19" (48 .26) 21" (53 .34) Cable Sizes Inches (cm) 13" (33 .02) 14" (35 .56) 15" (38 .10) Conduit Sizes Catalog Number Inches Approx. Breaking Strength Lbs. (N) 11/4 02213003 1,020 (4,537) 11/2 02213007 970 (4,315) -- 02213009 1,610 (7,161) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2 -- 02213012 02213013 1,520 (6,761) 1,610 (7,161) 21/2 -- -- 02213017 02213018 1,510 (6,716) 1,610 (7,161) 3 -- -- 02213023 02213024 02213025 02213026 1,400 (6,227) 1,490 (6,627) 1,990 (8,851) 3,260 (14,500) 31/2 -- -- -- -- -- 02213033 2,970 (13,211) 4 -- -- -- -- -- 02213041 02213042 2,670 (11,876) 2,890 (12,855) Note: See page T-47 for multiple cables in a single conduit riser grip. Dimensions in Inches (cm) www.hubbell-wiring.com T-41 Conduit Riser Grips -- Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Support Grips Kellems Support Grips Kellems Support Grips are used to hold the weight of electrical cable as it hangs in a vertical, sloping or horizontal position . Electrical cable must be supported, or its dead weight can cause excessive strain or pullout at the connections resulting in power failure . Support grips also absorb additional strain from flexure, vibration, expansion and contraction . Kellems Support Grips listed in this catalog are made of high grade, non-magnetic tin-coated bronze strand . Stainless steel grips, made of alloy 302-304 SST for severe service or unusual environmental conditions, are available on request . Select the Correct Support Grip Each Kellems grip is designed to work on a specific range of cable diameters . Step 1 Refer to the Kellems chart below to determine the grip style best suited for your application . Step 2 Determine your cable outside diameter . Step 3 Find the grip size that encompasses your cable diameter . Step 4 Whenever possible, use a closed mesh that assembles over the cable end . If the cable end is not available, use a split mesh . Step 5 Where available, select an eye style that suits your needs . Step 6 Select the proper material--tinned bronze or stainless steel* . Step 7 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed approximate breaking strength of the grip to insure that the grip will be strong enough . Refer to page T-43 for safety and working load considerations . Support Grip Selection Chart CAUTION: It is very important to comply with all of the following precautions . 1 . Support grips are to be installed by a qualified individual in accordance with all applicable national and local safety, electrical and rigging codes . 2 . Ensure that the correct grip is selected for your specific needs . 3 . Do not use a support grip for any application other than supporting cable . 4 . Thoroughly examine the grip for damage . Do not use a damaged grip . 5 . Ensure that the recommended work load of the grip is suitable for the application . Never use grips at their approximated rated breaking strength . A safety factor of 10 is recommended for support grips . 6 . Do not alter grips in any way . For example, do not flatten, straighten, bend or otherwise modify eye tubes, hooks, and strand equalizers . 7 . Do not attach any type of hook, clamp or other hardware directly to the stranded bale of a "U" eye support grip . The formed eye tube is the only acceptable means of attachment to external hardware . 8 . Always apply 2 bands at 1" and 2" respectively, from the tail end of the mesh to guard against accidental release of the grip . Accidental release can occur if an object contracts and pushes against the tail end of the mesh, thereby expanding and releasing it's hold . Grip Styles Application Page Closed mesh Split lace closing Split rod closing Standard, permanent support, cable end available . Standard, permanent support, cable end unavailable . Standard, temporary support, cable end unavailable . Tape or band tail end of wire mesh grip after positioning for permanent support . Tin-coated bronze standard or stainless steel by special request . Support vertical runs to 99 ft . loads to 600 lbs . Support vertical runs over 100 ft . loads over 600 lbs . Light duty to support service entrance cable . Light duty support, indoors only, on Bus drop cable . Support cable runs in rigid (Schedule 40) conduit . Support fiber optic cable . T-30 to T-38 T-30 to T-35 T-30 to T-33 Material* Standard support grips Heavy duty grips Service drop Bus drop Conduit riser Fiber optic cable support grips T-30 to T-41 T-30 to T-33 T-34, T-35 T-36, T-37 T-38 T-39 to T-41 T-53 Technical Information Note: * Most catalog listed support grips are made of tin-coated bronze strand. To order stainless steel support grips, change the first three catalog number digits from 022-0x-xxx to 024-0x-xxx. Consult Technical Service for details. Eye Styles Single T-42 Double Universal www.hubbell-wiring.com Offset Dimensions in Inches (cm) Technical Information Support Grips Safety And Working Load Factors For Wire Mesh Grips The broad application of Kellems grips on a wide variety of objects requires that adequate safety factors be used to establish working loads . The approximate breaking strength of a Kellems grip represents an average calculation based on data established from actual direct tension testing done in our engineering laboratories . It is impossible to catalog or guarantee a safety factor suitable for all applications as operating conditions are never the same . The tension, diameter, movement, number of objects gripped, gripping surface, and the attachments used are just some of the factors which vary with each application . These factors, together with the effects of abrasion, corrosion, prior use or abuse and any other variables of a specific application, must be considered by the user and the grip replaced as appropriate . Where the conditions of the application are not well defined or known, or where risk of injury to persons or property is involved, a greater safety factor should be utilized . Under normal conditions, Kellems' recommended factor of safety is five for catalog listed pulling grips, and ten for catalog listed support grips. Any warranty as to quality, performance or fitness for use of grips is always premised on the condition that the published breaking strengths apply only to new, unused grips, and that such products are properly stored, handled, used, maintained, and inspected by the user at a frequency appropriate for the use and condition of the grip . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Examples Grip Style Approx. Breaking Strength Lbs. (N) Safety Factor Max. Rec. Load Lbs. (N) Catalog Number Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027 Support Grips 1,610 (7,161) 10 161 (716) 02202019 The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to take care of unforeseen and unusual circumstances . It is the end-user's decision to determine how much of a safety factor is acceptable for the application . The metric unit of measure (force) for breaking strength and load is newtons (N) . To convert from newtons to the metric unit of weight (kilograms) the conversion factor is 9 .808 newtons/kilogram . Support Grip Materials Material Tin-coated bronze wire Stainless steel wire (302-304) Galvanized steel wire Grip Type * Support grips * Service drop grips * Conduit riser grips * Support grips * Hose containment grips * Bus drop grips Technical Information Features * Corrosion resistant for normal outside areas * Non-magnetic * Moderate strength * High strength * Corrosion resistant * Slightly magnetic * Not subject to continuous outside environment Approvals CSA Certifications are indicated on appropriate product catalog pages . Note: It is always recommended that the tail end of the grip be banded after the installation on the cable to prevent accidental release of the mesh. See page T-15 for end bands. Dimensions in Inches (cm) www.hubbell-wiring.com T-43 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Support Grips Split Support Grip Lace Closing Instructions Single Weave Grips should be laced with single strand lacing; double weave with double strand . Lacing strands should be the same material as the grip . Kellems supplies the appropriate lacing with each grip . 1. Start the lacing at the lead or anchoring end of the grip . Thread the lacings through the first two loops of the split and pull through until the lacings are centered at this point . Lace as you would your shoe, crossing the lacings before lacing the next two loops . 2. Don't pull lacing too tight . Leave a space between adjoining loops approximately equal to the width of one diamond of the mesh . 3. Twist the lacing strands tightly together at the tail end of the grip . 4. Wrap the ends of the lacings once or twice tightly around the tail of the grip, twisting the ends together securely . Excess lace can be cut off . Technical Information Split Support Grip Rod Closing Instructions The stainless steel rod is a precise built-in feature which makes threading easy and fast . The strands of the mesh pass around the rod and match up with the strands from the opposite direction . The rod does not touch the cable at any point and therefore cannot cut the cable . Rod Closing Grips are reusable . They may be removed and reused as many times as desired . 1. Fast to install Wrap the grip around the cable and thread the rod through the pre-formed loops with a corkscrew motion, using the curved end of the rod to engage the loops . 2. The action required is a steady push and twist simultaneously . The fingers of the left hand are used to bring the loops together just ahead of the hook on the end of the rod . 3. To remove, simply pull the rod out . T-44 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Bus Drop Grips Bus Drop Grips and Safety Springs Kellems Bus Drop Grips are offered with either a single eye or universal bale attachment . The mesh is single weave galvanized steel with the patented wide range construction . They are suitable for indoor use only . Safety Spring Strain Relief Grip Bus Drop Grips Strain Relief Grip Motor Box Application Bus Drop Grips provide a safe, easy and economical method to support flexible cord or bus drop cable at bus duct and other industrial areas . Benefits Kellems(R) Wire Management Products Kellems(R) Wire Management Products * Easily installed. * Absorb tension, vibration and pull with no cable damage. * Patented mesh construction. Safety Spring Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye and replacing drawbar . Technical Information Dimensions in Inches (cm) www.hubbell-wiring.com T-45 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Support Grips For Support Grips Only* Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters How to choose the correct grip size: 1. Find the Grip Circumference Range by measuring the circumference of the bundle of different diameter cables to be gripped (see illustration) . 2. Divide the bundle circumference by 3 .14 to determine the diameter . 3. Choose a grip offering a range of cable diameters the same as the cable diameter . For Cables of Equal Diameters Under "Number of Cables in One Grip", find the diameter of your single cable in vertical column . Read the grip diameter range to the right . If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips . Example: 3 cables, each with .89" (2 .26cm) diameter, for a Closed Grip select the 1 .50"-1 .74" (3 .81cm-4 .42cm) range, for a Split Grip select the 1 .75"-1 .99" (4 .44cm-5 .05cm) range . Conduit Riser Grips Number of Cables in One Grip 2 3 4 5 6 and 7 8 9 Grip Dia. Range Inches (cm) .30- .38 ( .76- .97) .38- .44 ( .97-1 .12) .44- .59 (1 .12-1 .50) .59- .75 (1 .50-1 .90) .75- .90 (1 .90-2 .29) .90-1 .07 (2 .29-2 .72) 1 .07-1 .22 (2 .72-3 .10) 1 .22-1 .53 (3 .10-3 .89) 1 .53-1 .83 (3 .89-4 .65) 1 .83-2 .14 (4 .65-5 .44) 2 .14-2 .44 (5 .44-6 .20) 2 .44-2 .75 (6 .20-6 .98) 2 .75-3 .06 (6 .98-7 .77) .25- .31 ( .63- .79) .31- .36 ( .79- .91) .36- .49 ( .91-1 .24) .49- .63 (1 .24-1 .60) .63- .76 (1 .60-1 .93) .76- .89 (1 .93-2 .26) .89-1 .02 (2 .26-2 .59) 1 .02-1 .28 (2 .59-3 .25) 1 .28-1 .53 (3 .25-3 .89) 1 .53-1 .79 (3 .89-4 .55) 1 .79-2 .05 (4 .55-5 .21) 2 .05-2 .30 (5 .21-5 .84) 2 .30-2 .56 (5 .84-6 .50) .22- .27 ( .56- .69) .27- .31 ( .69- .79) .31- .42 ( .79-1 .07) .42- .54 (1 .07-1 .37) .54- .65 (1 .37-1 .65) .65- .77 (1 .65-1 .96) .77- .88 (1 .96-2 .24) .88-1 .10 (2 .24-2 .79) 1 .10-1 .32 (2 .79-3 .35) 1 .32-1 .54 (3 .35-3 .91) 1 .54-1 .76 (3 .91-4 .47) 1 .76-1 .98 (4 .47-5 .03) 1 .98-2 .20 (5 .03-5 .59) .19- .24 ( .48- .61) .24- .29 ( .61- .74) .29- .38 ( .74- .97) .38- .48 ( .97-1 .22) .48- .58 (1 .22-1 .47) .58- .67 (1 .47-1 .70) .67- .77 (1 .70-1 .96) .77- .96 (1 .96-2 .44) .96-1 .16 (2 .44-2 .95) 1 .16-1 .35 (2 .95-3 .43) 1 .35-1 .54 (3 .43-3 .91) 1 .54-1 .74 (3 .91-4 .42) 1 .74-1 .93 (4 .42-4 .90) .17- .22 ( .43- .56) .22- .26 ( .56- .66) .26- .34 ( .66- .86) .34- .43 ( .86-1 .09) .43- .52 (1 .09-1 .32) .52- .60 (1 .32-1 .52) .60- .69 (1 .52-1 .75) .69- .86 (1 .75-2 .18) .86-1 .03 (2 .18-2 .62) 1 .03-1 .20 (2 .62-3 .05) 1 .20-1 .37 (3 .05-3 .48) 1 .37-1 .55 (3 .48-3 .94) 1 .55-1 .72 (3 .94-4 .37) .15- .19 ( .38- .48) .19- .23 ( .48- .58) .23- .31 ( .58- .79) .31- .39 ( .79- .99) .39- .46 ( .99-1 .17) .46- .54 (1 .17-1 .37) .54- .62 (1 .37-1 .57) .62- .77 (1 .57-1 .96) .77- .93 (1 .96-2 .36) .93-1 .08 (2 .36-2 .74) 1 .08-1 .24 (2 .74-3 .15) 1 .24-1 .39 (3 .15-3 .53) 1 .39-1 .55 (3 .53-3 .94) .14- .18 ( .36- .46) .18- .21 ( .46- .53) .21- .28 ( .53- .71) .28- .35 ( .71- .89) .35- .42 ( .89-1 .07) .42- .49 (1 .07-1 .24) .49- .56 (1 .24-1 .42) .56- .71 (1 .42-1 .80) .71- .85 (1 .80-2 .16) .85- .99 (2 .16-2 .51) .99-1 .13 (2 .51-2 .87) 1 .13-1 .27 (2 .87-3 .23) 1 .27-1 .41 (3 .23-3 .58) .50- .61 (1 .27-1 .55) .62- .74 (1 .57-1 .88) .75- .99 (1 .90-2 .51) 1 .00-1 .24 (2 .54-3 .15) 1 .25-1 .49 (3 .17-3 .78) 1 .50-1 .74 (3 .81-4 .42) 1 .75-1 .99 (4 .44-5 .05) 2 .00-2 .49 (5 .08-6 .32) 2 .50-2 .99 (6 .35-7 .59) 3 .00-3 .49 (7 .62-8 .86) 3 .50-3 .99 (8 .89-10 .13) 4 .00-4 .49 (10 .16-11 .40) 4 .50-4 .99 (11 .43-12 .67) Note: * This chart is to be used for determining grip size when multiple cables are held in a single Support Grip. For Conduit Riser multiple cable selection, see page T-47. It is always recommended that, when multiple cables are installed in a Support Grip, the tail end of the grip be banded after installation on the cable bundle. T-46 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Conduit Riser Support Grips For Conduit Riser Grips Only* Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters How to choose the correct grip size: 1 . Find the Grip Circumference Range by measuring the circumference of the bundle of different diameter cables to be gripped (see illustration) . 2 . Divide the bundle circumference by 3 .14 to determine the diameter . 3 . Choose a grip offering a range of cable diameters the same as the cable diameter . For Cables of Equal Diameters Under "Number of Cables in One Grip", find the diameter of your single cable in vertical column . Read the grip diameter range to the right . If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips . Example: 3 cables, each with .85" (2 .16cm) diameter, for a Closed Grip select the 1 .50"-1 .74" (3 .81cm-4 .42cm) range, for a Split Grip select the 1 .75"-1 .99" (4 .44cm-5 .05cm) range . Number of Equal Diameter Cables in One Grip 3 4 5 6 and 7 8 9 Grip Dia. Range Inches (cm) .29- .36 ( .74- .91) .37- .43 ( .94-1 .09) .44- .58 (1 .12-1 .47) .59- .72 (1 .50-1 .83) .73- .87 (1 .85-2 .21) .88-1 .01 (2 .24-2 .57) 1 .02-1 .16 (2 .59-2 .95) 1 .17-1 .44 (2 .97-3 .66) 1 .45-1 .73 (3 .68-4 .39) 1 .74-2 .02 (4 .42-5 .13) 2 .03-2 .31 (5 .16-5 .87) .24- .30 ( .61- .76) .31- .36 ( .79- .91) .37- .48 ( .94-1 .22) .49- .60 (1 .24-1 .52) .61- .72 (1 .55-1 .83) .73- .85 (1 .85-2 .16) .86- .96 (2 .18-2 .44) .97-1 .20 (2 .46-3 .05) 1 .21-1 .45 (3 .07-3 .68) 1 .46-1 .69 (3 .71-4 .29) 1 .70-1 .93 (4 .32-4 .90) .21- .25 ( .53- .63) .26- .30 ( .66- .76) .31- .41 ( .79-1 .04) .42- .51 (1 .07-1 .30) .52- .61 (1 .32-1 .55) .62- .71 (1 .57-1 .80) .72- .81 (1 .83-2 .06) .82-1 .02 (2 .08-2 .59) 1 .03-1 .22 (2 .62-3 .10) 1 .23-1 .43 (3 .12-3 .63) 1 .44-1 .63 (3 .66-4 .14) .18- .22 ( .46- .56) .23- .27 ( .58- .69) .28- .36 ( .71- .91) .37- .45 ( .94-1 .14) .46- .54 (1 .17-1 .37) .55- .63 (1 .40-1 .60) .64- .72 (1 .63-1 .83) .73- .90 (1 .85-2 .29) .91-1 .08 (2 .31-2 .74) 1 .09-1 .26 (2 .77-3 .20) 1 .27-1 .44 (3 .23-3 .66) .16- .20 ( .41- .51) .21- .24 ( .53- .61) .25- .32 ( .63- .81) .33- .40 ( .84-1 .02) .41- .48 (1 .04-1 .22) .49- .56 (1 .24-1 .42) .57- .64 (1 .45-1 .63) .65- .80 (1 .65-2 .03) .81- .96 (2 .06-2 .44) .97-1 .11 (2 .46-2 .82) 1 .12-1 .27 (2 .84-3 .23) .15- .18 ( .38- .46) .19- .22 ( .48- .56) .23- .29 ( .58- .74) .30- .36 ( .76- .91) .37- .43 ( .94-1 .09) .44- .51 (1 .12-1 .30) .52- .58 (1 .32-1 .49) .59- .72 (1 .50-1 .83) .73- .87 (1 .85-2 .21) .83-1 .01 (2 .11-2 .57) 1 .02-1 .15 (2 .59-2 .92) .14- .17 ( .36- .43) .18- .20 ( .46- .51) .21- .27 ( .53- .69) .28- .34 ( .71- .86) .35- .40 ( .89-1 .02) .41- .47 (1 .04-1 .19) .48- .54 (1 .22-1 .37) .55- .67 (1 .40-1 .70) .68- .81 (1 .73-2 .06) .82- .94 (2 .08-2 .39) .95-1 .08 (2 .41-2 .74) .50- .62 (1 .27-1 .57) .63- .74 (1 .60-1 .88) .75- .99 (1 .90-2 .51) 1 .00-1 .24 (2 .54-3 .15) 1 .25-1 .49 (3 .17-3 .78) 1 .50-1 .74 (3 .81-4 .42) 1 .75-1 .99 (4 .44-5 .05) 2 .00-2 .49 (5 .08-6 .32) 2 .50-2 .99 (6 .35-7 .59) 3 .00-3 .49 (7 .62-8 .86) 3 .50-3 .99 (8 .89-10 .13) Note: * This chart is to be used for determining grip size when multiple cables are held in a single Conduit Riser Grip. For Support Grip multiple cable selection, see page T-46. It is always recommended that, when multiple cables are installed in a Conduit Riser Grip, the tail end of the grip be banded after installation on the cable bundle. Dimensions in Inches (cm) www.hubbell-wiring.com T-47 Technical Information 2 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Conduit Riser Grips Conduit Riser Support Grip-Ring Dimensions WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-41 through T-48 . Conduit Ring Dimensions Ring dimensions are found in the chart below . The ring material is corrosion resistant . These rings will fit schedule 40 rigid PVC conduit and standard electrical rigid metal conduit only . O.D. I.D. T Conduit Size 3/4" and 1" O.D. I.D. Conduit Size Inches Ring Number O.D. Inches (cm) I.D. Inches (cm) S Inches (cm) T Inches (cm) 3/4 1 11/4 11/2 2 21/2 3 31/2 4 41/2 5 6 C-3/4 C-1 C-11/4 C-11/2 C-2 C-21/2 C-3 C-31/2 C-4 C-41/2 C-5 C-6 .94" (2 .39) 1 .17" (2 .97) 1 .50" (3 .81) 1 .76" (4 .47) 2 .23" (5 .66) 2 .67" (6 .78) 3 .20" (8 .13) 3 .80" (9 .65) 4 .30" (10 .92) 4 .80" (12 .19) 5 .30" (13 .46) 6 .30" (16 .00) .62" (1 .57) .80" (2 .03) 1 .03" (2 .62) 1 .23" (3 .12) 1 .55" (3 .94) 2 .05" (5 .21) 2 .55" (6 .48) 3 .05" (7 .75) 3 .55" (9 .02) 4 .03" (10 .24) 4 .46" (11 .33) 5 .36" (13 .61) -- -- 1 .31" (3 .33) 1 .52" (3 .86) 1 .97" (5 .00) 2 .40" (6 .10) 2 .97" (7 .54) 3 .47" (8 .81) 3 .94" (10 .01) 4 .45" (11 .30) 4 .96" (12 .60) 5 .96" (15 .14) .19" ( .48) .19" ( .48) .16" ( .41) .16" ( .41) .16" ( .41) .16" ( .41) .22" ( .56) .22" ( .56) .22" ( .56) .22" ( .56) .22" ( .56) .25" ( .63) T T S Technical Information Conduit Size 11/4" to 6" T-48 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Fiber Optic Cable Grips Pulling and Support Grips OPTISOK(R) Grip is a revolutionary tool to pull preterminated fiber optic cables . They will protect the connectors and guide the bundle through the pulling environment Pulling Grips are used for outside plant cable . They are easy to install and remove, reusable, and have a slim profile for small build up Grips for cable support are easy to install or position . They come in a closed style when the cable end is available, and a split rod style for mid-span installation . Will support the cable's weight as it hangs in vertical, sloping or horizontal position Fiber Optic Cable Grips Dimensions in Inches (cm) www.hubbell-wiring.com T-49 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Fiber Optic Cable Pulling Grips Special Purpose OPTISOK(R) Non-metallic Fiber Optic Pulling Tool For Preterminated, Inside Plant Fiber Optic Cables and Bundles of Twisted Pair WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-54 through T-57 . OPTISOK(R) Non-Metallic Fiber Optic Pulling Tool Bundle/Size Range Inches (cm) Approx. O/A Length Inches (cm) Ring O.D. Inches (cm) Ring Thickness Inches (cm) Maximum Work Load lbs. (N) Catalog Number .125"- .562" ( .318-1 .427) .250"- .750" ( .635-1 .905) .750"-1 .750" (1 .905-4 .445) 28" (71 .12) 31" (78 .74) 33" (83 .82) .71" (1 .803) .71" (1 .803) 1 .57" (3 .988) .10" ( .254) .10" ( .254) .16" ( .406) 30 (133) 40 (178) 50 (222) CCPS1 CCPS2 CCPS3 Fiber Optic Cable Pulling Grips Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel Diameter Range Inches (cm) Mesh Length Inches (cm) Eye Length Inches (cm) Eye Diameter Inches (cm) Lug Diameter Inches (cm) Maximum Breaking Strength lbs. (N) Catalog Number .312"- .625" ( .79-1 .59) 22 .5" (57 .15) 6 .3" (16 .00) .20" ( .51) .51" (1 .30) 3,000 (13,344) PFOLT312 T-50 www.hubbell-wiring.com Dimensions in Inches (cm) Fiber Optic Cable Pulling Grips Double/Single Weave Mesh, Galvanized Steel, for Outside Plant Cable WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-54 through T-57 . F-O Pulling Grip, Flexible Eye Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) D Approx. Inches (cm) Catalog Number .10"- .22" ( .25- .56) 1,000 (4,448) 5 .5" (14) 9" (23) 0 .8" (2) 033291000 .21"- .35" ( .53- .89) 1,500 (6,672) 5 .5" (14) 14" (36) 0 .8" (2) 033291001 .32"- .48" ( .81-1 .22) 2,200 (9,786) 6 .0" (15) 18" (46) 0 .9" (2 .29) 033291002 .42"- .61" (1 .07-1 .55) 2,800 (12,454) 6 .0" (15) 21" (53) 0 .9" (2 .29) 033291003 .53"- .74" (1 .35-1 .88) 3,300 (14,678) 6 .5" (17) 24" (61) 1 .3" (3 .30) 033291004 .64"- .87" (1 .63-2 .21) 4,700 (20,906) 6 .5" (17) 27" (69) 1 .3" (3 .30) 033291005 Kellems(R) Wire Management Products Kellems(R) Wire Management Products F-O Pulling Grip, Swivel Eye Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) D Approx. Inches (cm) Catalog Number .21"- .35" ( .53- .89) 1,500 (6,672) 4 .0" (10 .16) 14" (35 .56) 0 .9" (2 .29) 033291008 .32"- .48" ( .81-1 .22) 2,200 (9,786) 4 .0" (10 .16) 18" (45 .72) 0 .9" (2 .29) 033291009 .42"- .61" (1 .07-1 .55) 2,800 (12,454) 4 .0" (10 .16) 21" (53 .34) 0 .9" (2 .29) 033291010 .53"- .74" (1 .35-1 .88) 3,300 (14,678) 4 .5" (11 .43) 24" (60 .96) 1 .3" (3 .30) 033291011 .64"- .87" (1 .63-2 .21) 4,700 (20,906) 4 .5" (11 .43) 27" (68 .58) 1 .3" (3 .30) 033291012 Fiber Optic Cable Pulling Grips Cable Diameter Range Inches (cm) Note: E-Eye length. M-Mesh length at nominal diameter. Dimensions in Inches (cm) www.hubbell-wiring.com T-51 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Fiber Optic Cable Pulling Grips Galvanized Steel for Outside Plant Cable WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-54 through T-57 . F-O Pulling Grip, Flexible Eye, Low Profile, Double/Single Weave Mesh Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number .10"- .22 ( .25- .56) 900 (4,003) 7 .5" (19) 10" (25) 033291193 .21"- .35" ( .53- .89) 1,400 (6,227) 7 .5" (19) 14" (36) 033291194 .32"- .48" ( .81-1 .22) 2,000 (8,896) 8 .5" (22) 19" (48) 033291195 .42"- .61" (1 .07-1 .55) 2,500 (11,120) 8 .5" (22) 21" (53) 033291196 .53"- .74" (1 .35-1 .88) 3,000 (13,344) 8 .5" (22) 23" (58) 033291197 .64"- .87" (1 .63-2 .21) 4,200 (18,682) 8 .5" (22) 25" (64) 033291198 .75"-1 .00" (1 .90-2 .54) 4,200 (18,682) 8 .5" (22) 28" (71) 033291199 Fiber Optic Cable Pulling Grips F-O Slack Pulling Grip, Split Mesh Rod Closing, Single Weave Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number .25"- .37" ( .63- .94) 300 (1,334) 3" (7 .6) 4 .7" (12) 033291015 .38"- .49" ( .97-1 .24) 800 (3,558) 3" (7 .6) 5" (13) 033291016 .50"- .61" (1 .27-1 .55) 800 (3,558) 3" (7 .6) 7 .5" (19) 033291017 .62"- .74" (1 .57-1 .88) 1,200 (5,338) 3" (7 .6) 8" (20) 033291018 Note: E-Eye length. M-Mesh length at nominal diameter. T-52 www.hubbell-wiring.com Dimensions in Inches (cm) Fiber Optic Cable Support Grips Single Weave, Tin-Coated Bronze F-O Single Eye Cable Support Grip, Closed Mesh, Single Weave Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number .18"- .25" ( .46- .63) 300 (1,334) 3" (7 .6) 1 .7" (4 .3) 022291000 .23"- .32" ( .58- .81) 300 (1,334) 3" (7 .6) 2 .5" (6 .4) 022291001 .30"- .39" ( .76- .99) 300 (1,334) 4" (10) 2 .5" (6 .4) 022291002 .37"- .48" ( .94-1 .22) 300 (1,334) 5" (13) 4" (10) 022291003 .46"- .58" (1 .17-1 .47) 400 (1,779) 6" (15) 4" (10) 022291004 .56"- .71" (1 .42-1 .80) 600 (2,669) 7" (18) 5 .5" (14) 022291005 .69"- .88" (1 .75-2 .24) 800 (3,558) 8" (20) 6" (15) 022291006 F-O Single Eye Cable Support Grip, Split Mesh, Rod Closing, Single Weave Cable Diameter Range Inches (cm) Approx. Breaking Strength Lbs. (N) E Approx. Inches (cm) M Approx. Inches (cm) Catalog Number .18"- .25" ( .46- .63) 300 (1,334) 3" (7 .6) 2 .5" (6 .4) 022291016 .23"- .32" ( .58- .81) 300 (1,334) 3" (7 .6) 2 .5" (6 .4) 022291017 .30"- .39" ( .76- .99) 300 (1,334) 4" (10) 2 .5" (6 .4) 022291018 .37"- .48" ( .94-1 .22) 300 (1,334) 5" (13) 4" (10) 022291019 .46"- .58" (1 .17-1 .47) 400 (1,779) 6" (15) 5" (13) 022291020 .56"- .71" (1 .42-1 .80) 600 (2,669) 7" (18) 5" (13) 022291021 .69"- .88" (1 .75-2 .24) 800 (3,558) 8" (20) 6" (15) 022291022 WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-54 through T-57 . For permanent support when cable end is available to be installed through grip . Single Eye, Closed Mesh, Single Weave For support when cable end not available . Fiber Optic Cable Support Grips Note: E-Eye length. M-Mesh length at nominal diameter. Single Eye, Split Mesh, Rod Closing, Single Weave Dimensions in Inches (cm) www.hubbell-wiring.com Kellems(R) Wire Management Products Kellems(R) Wire Management Products T-53 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Fiber Optic Pulling and Support Grips Kellems has wide experience with grips for the new technology of fiber optic cable . As the industry leader in producing wire mesh grips for the stringent requirements of fiber optic applications, Kellems has developed several series of grips for use with fiber optic communications cable . Select the Correct Fiber Optic Grip These grips include pulling grips with built in swivels, grips with steel ends to protect fragile cable ends, grips with low profiles to pull cables in tight places and the OPTISOK(R) an effective tool to place preterminated cables . Also available are grips to support fiber optic cable . Step 3 Whenever possible, use a closed mesh that assembles over the cable end . If the cable end is not available, use a split mesh . Each Kellems grip is designed to work on a specific range of cable diameters . Step 1 Determine your cable outside diameter . Step 2 Find the grip size that encompasses your cable diameter . Step 4 Where available, select an eye style that suits your needs . Step 5 Estimate the tension to be put on the grip, establish the working load you require and compare this to the listed approximate breaking strength of the grip to insure that the grip will be strong enough . Safety And Working Load Factors For Wire Mesh Grips The broad application of Kellems grips on a wide variety of objects requires that adequate safety factors be used to establish working loads . The approximate breaking strength of a Kellems grip represents an average calculation based on data established from actual direct tension testing done in our engineering laboratories . It is impossible to catalog or guarantee a safety factor suitable for all applications as operating conditions are never the same . The tension, diameter, movement, number of objects gripped, gripping surface, and the attachments used are just some of the factors which vary with each application . These factors, together with the effects of abrasion, corrosion, prior use or abuse and any other variables of a specific application, must be considered by the user and the grip replaced as appropriate . Where the conditions of the application are not well defined or known or where risk of injury to persons or property is involved, a greater safety factor should be utilized . Under normal conditions, Kellems' recommended factor of safety is five for catalog listed pulling grips, and ten for catalog listed support grips. Any warranty as to quality, performance or fitness for use of grips is always premised on the condition that the published breaking strengths apply only to new, unused grips, and that such products are properly stored, handled, used, maintained and inspected by the user at a frequency appropriate for the use and condition of the grip . For grip applications on materials other than those that the grips have been specifically designed for, consult the factory . Examples Grip Style Approx. Breaking Strength Lbs. (N) Safety Factor Max. Rec. Load Lbs. (N) Catalog Number Pulling Grips Support Grips 2,500 (11,120) 400 (1,779) 5 10 500 (2,224) 40 (178) 033291196 022291004 The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to take care of unforeseen and unusual circumstances. It is the end-user's decision to determine how much of a safety factor is acceptable to for the application. Technical Information Fiber Optic Grip Materials Material Features Product Group Galvanized steel wire * High strength * Not subject to continuous outside environment * Pulling grips Tin-coated bronze wire * Corrosion resistant for normal outside areas * Non-magnetic * Moderate strength * Support grips Non-metallic braid * Superior flex life * Non-conductive * Corrosion resistant * Moderate strength * OPTISOK(R) Approvals CSA Certification is indicated on appropriate product catalog pages . T-54 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information OPTISOK(R) Pulling Grips Kellems offers a unique and simple to use tool for the installation of preconnectorized fiber optic cables, jumpers and bundles of twisted pair communication cables - the OPTISOK(R) . The OPTISOK(R) is a highly flexible and expandable nonmetallic sleeve open on one end and with a pulling ring on the other . It will expand to enclose the larger group of fiber optic connectors and grab the cable below the connector bundle by wrapping and taping to provide a gripping tool that will grab the cable(s) below the connectors . The pulling ring can be attached to a pulling line or fish tape and the OPTISOK(R) will act as the pulling tool . OPTISOK(R) will contain and protect the connector bundle and save time and labor by making the pulling job easier, protecting the connectors from possible damage during the pull and facilitating the passage of the connector bundle through cramped and tight spaces . The OPTISOK(R) can be used to pull cables through plenums, underfloor duct, office partitions, raised access floors and conduits . Three sizes are available for all applications . 1 2 How to Select OPTISOK(R) * Identify connector bundle diameter to be inserted into the OPTISOK(R) . * Choose appropriate catalog number based on size range. Installation Information Step 1. Expand open end of OPTISOK(R) and gently work in fiber optic connector bundle . Step 2. Still gently, work connector bundle up to the forward section of the OPTISOK(R) . Step 3. Starting at approximately 6" (15 .2cm) from tail end of OPTISOK(R), tightly fold over the OPTISOK(R) around cables and tape wrapped section 3" (7 .62cm) past tail end onto the bundle . 3 Step 4. Securely attach pulling line or tape to pulling ring . Technical Information Note To remove OPTISOK(R) carefully unwrap tape and slide out cables and connectors or cut OPTISOK(R) away without damaging connectors or cables. 4 Dimensions in Inches (cm) www.hubbell-wiring.com T-55 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Fiber Optic Pulling Grips Pulling Grip for Loose Tube Fiber Optic Cable Kellems offers a wire mesh specifically designed to pull loose tube fiber optic cable and meet the special pulling requirements recommended by fiber optic cable manufacturers . Many fiber optic cable manufacturers require special cable preparation prior to pulling where a short section of the outer jacket is stripped off exposing the aramid strength member . This creates two cable diameters, one including the jacket and a second smaller diameter at the strength member . Kellems fiber grip with its special weave will accommodate and securely grab both diameters, at the outside jacket and the internal aramid strength member . Additionally, this galvanized steel mesh grip has longer leads at the pulling eye to facilitate pulling the cable up through the top, a very low profile lug and eye to slip through tight areas, and short shoulders to protect the cable while maintaining the slim profile . The grip can be used to pull cable overhead as well as underground through conduit and duct . It easily mates with a swivel and has the necessary strength to securely make pulls . Application Information * Prior to pulling cable, follow cable manufacturers' cable preparation recommendations. * Never exceed cable manufacturers' pulling tension recommendations. * Never use grips to approximate breaking strength safety factor of 5 recommended. Pulling Grips for Other Outside Plant Cables, Swivel Eye, Flexible Eye, Split Style, Low Profile Kellems Pulling Grips for fiber optic cable are made of high strength galvanized steel strand . They feature a multiweave mesh, with one-half the mesh length double weave, and the second half single weave . This special weave provides positive holding power while allowing the grip to remain flexible with no damage to the cable jacket . Added features include a steel nose cone which protects the cable end and allows the grip to pass easily through conduit and enclosures . The eye connects easily to a swivel or a pulling line . Several grip sizes are available to accommodate all diameters of fiber optic cable . Application Kellems Flexible Eye Pulling Grips for fiber optic cable are used for the installation of fiber optic communication lines either underground, overhead, through conduit or through enclosures . They will fit single cables or cable bundles, are easily installed on the cable, and are reusable . Technical Information Benefits * * * * * High strength multiweave mesh for positive holding power. Highly flexible mesh to follow the pulling path of the cable. Steel nose cone reduces snags and hang-ups and protects cable end. Easily installed and removed. A dependable, reusable pulling tool. T-56 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Fiber Optic Support Grips Support Grips for Fiber Optic Cable Kellems Support Grips for fiber optic cable are specially designed to hold the cable weight as it hangs in a vertical or horizontal position . Fiber optic cable must be supported and Kellems Grips provide the support easily and economically . These grips are made of high grade, non-magnetic tin-coated bronze strand . They are offered in universal bale or single eye configurations and are available in either closed mesh (for use where the cable end is available) or in split mesh, rod closing (for installation on existing cable runs or at specific locations) . Split Support Grip Rod Closing Instructions The stainless steel rod is a precise built-in feature which makes threading easy and fast . The strands of the mesh pass around the rod and match up with the strands from the opposite direction . The rod does not touch the cable at any point and therefore cannot cut the cable . Rod Closing Grips are reusable . They may be removed and reused as many times as desired . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Fast to Install Step 1. Wrap the grip around the cable and thread the rod through the preformed loops with a corkscrew motion, using the curved end of the rod to engage the loops . Step 2. The action required is a steady push and twist simultaneously . The fingers of the left hand are used to bring the loops together just ahead of the hook on the end of the rod . Step 3. To remove, simply pull the rod out . Technical Information Dimensions in Inches (cm) www.hubbell-wiring.com T-57 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Hose Containment Grips WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-42 through T-43 . Types of Attachment The five attachment methods shown below provide unlimited flexibility of attachment to meet any condition . Type E Double Eye Grip, used where fastening is made with eyebolts or similar anchor terminations . Type A Single Eye Grip, used where fastening MUST be made from one point . Type U Universal Bale Grip, used to fasten around a structure or closed eye . Type Y Threaded bolt (-18 x 11/2" long), used to fasten through drilled holes in plate . Type F Hose Containment Grips Split fitting to fit AN-818 nuts . Fitting is positioned over nut and located with internal flange . A hose clamp is furnished and required to hold the fitting in correct position . Note: It should be emphasized that Kellems(R) Hose Containment Grips are not to be used as a pressure reinforcing device for hose systems. These grips are custom made. Consult Technical Services for details. Kellems Hose Containment Grips are used on high pressure, flexible hose lines to prevent the hose from whipping violently in the event of hose failure at the fitting . These grips will prevent serious injury to personnel and damage to equipment by holding the hose in place in the event of hose failure . Kellems patented Hose Containment Grips are made of stainless steel with double weave mesh construction for high strength and come complete with hose clamps . Kellems Hose Containment Grips are supplied in diameters, length and attachments to meet individual requirements . Contact the Wiring Device-Kellems factory for specific information . These grips help meet OSHA Federal Register 1926-302 (b), 1926-603 (9), (10), JIC H-1-1973 (H13 .11) and JIC P-1-1975 (P11 .34) requirements . T-58 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Strain Relief for Flexible Cords For Insulated Cables and Flexible, Liquidtight Conduits Endless weave provides easy cable/flexible conduit installation Stainless steel mesh is corrosion resistant . Can be used inside or outside. It eliminates cable or flexible conduit pull out and reduces costly downtime Multiweave grip gives cable arc-of-bend control minimizing cable damage and extending cable life . It is the strongest strain relief device available . Meets and exceeds all code requirements; prevents cable/conduit pull-out Strain Relief for Flexible Cords A liquidtight fitting is available with both cable and conduit fittings; prevents liquids from running through the fitting into the enclosure An N .P .T . and PG threaded body allows easy attachment to either threaded hub or knock-out in box Dimensions in Inches (cm) www.hubbell-wiring.com T-59 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Deluxe Cord Grips Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . Straight Male Thread N.P.T. Thread Size Inches 1/2 1/2 3/4 3/4 1 Straight Male 1 11/4 11/2 11/2 2 Deluxe Cord Grips 2 Note: Kellems(R) Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b). 21/2 3 * Cable jacket may have to be stripped to pass through connector body. 3 T-60 Grip Diameter Range Inches (cm) .250"- .312" .312"- .375" .375"- .437" .187"- .250" .250"- .375" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .187"- .250" .250"- .375" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .875"-1 .000" 1 .000"-1 .125" 1 .125"-1 .250" 1 .250"-1 .375" .750"- .875" .875"-1 .000" 1 .000"-1 .125" 1 .125"-1 .250" 1 .250"-1 .375" .750"- .875" .875"-1 .000" 1 .000"-1 .125" 1 .125"-1 .250" 1 .250"-1 .375" 1 .312"-1 .437" 1 .437"-1 .562" 1 .562"-1 .687" 1 .687"- 1 .812" 1 .750"-1 .875" 1 .250"-1 .375" 1 .312"-1 .437" 1 .437"-1 .562" 1 .562"-1 .687" 1 .687"-1 .812" 1 .750"- 1 .875" 1 .812"-1 .937" 1 .937"-2 .062" 2 .062"-2 .187" 2 .187"-2 .312" 2 .312"-2 .437" 1 .688"-1 .812" 1 .812"-1 .937" 1 .937"-2 .062" 2 .062"-2 .187" 2 .187"-2 .312" 2 .312"-2 .437" 1 .937"-2 .062" 2 .062"-2 .187" 2 .187"-2 .312" 2 .312"-2 .437" 2 .437"-2 .625" 2 .625"-2 .812" 2 .812"-3 .000" 3 .000"-3 .250" ( .63- .79) ( .79- .95) ( .95-1 .11) ( .47- .63) ( .63- .95) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) ( .47- .63) ( .63- .95) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) (2 .86-3 .17) (3 .17-3 .49) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) (2 .86-3 .17) (3 .17-3 .49) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) (2 .86-3 .17) (3 .17-3 .49) (3 .33-3 .65) (3 .65-3 .97) (3 .97-4 .28) (4 .28-4 .60) (4 .44-4 .76) (3 .17-3 .49) (3 .33-3 .65) (3 .65-3 .97) (3 .97-4 .28) (4 .28-4 .60) (4 .44-4 .76) (4 .60-4 .92) (4 .92-5 .24) (5 .24-5 .55) (5 .55-5 .87) (5 .87-6 .19) (4 .29-4 .60) (4 .60-4 .92) (4 .92-5 .24) (5 .24-5 .55) (5 .55-5 .87) (5 .87-6 .19) (4 .92-5 .24) (5 .24-5 .55) (5 .55-5 .87) (5 .87-6 .19) (6 .19-6 .67) (6 .67-7 .14) (7 .14-7 .62) (7 .62-8 .25) www.hubbell-wiring.com Form Size F1 F2 F3 F2 F3 F4 F5 F5 F5 F6 F6 F7 F7 F7 F8 Catalog Number 07401001 07401002 07401003 07401004 07401006 07401008 07401010 074011247* 074011248* 07401011 07401013 07401015 07401017 07401018 074011249* 074011195 07401019 07401021 07401023 07401025 074011250* 074011028* 074011029* 074011251 07401026 07401027 07401028 074011178* 074011252 07401029 07401030 07401031 07401032 074011253 074011254* 074011255* 074011256* 074011257* 074011258 074011259 07401033 07401034 07401035 074011260 074011261 074011262* 074011263* 074011264* 074011265* 074011030 074011031 074011032 074011033 074011034 074011266* 074011036 074011037 074011038 074011039 074011186 074011187 074011188 074011189* Dimensions in Inches (cm) Deluxe Cord Grips Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Straight Female Thread N.P.T. Thread Size Inches Grip Diameter Range Inches (cm) 1/2 .375"- .500" .500"- .625" .500"- .625" .625"- .750" 3/4 3/4 ( .95-1 .27) (1 .27-1 .59) (1 .27-1 .59) (1 .59-1 .90) Form Size F2 F2 F4 Catalog Number 07401043 07401045 07401052 07401053 WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . 90 Male Thread N.P.T. Thread Size Inches 1/2 3/4 1 11/4 11/2 2 Grip Diameter Range Inches (cm) .250"- .312" .312"- .375" .375"- .437" .187"- .250" .250"- .375" .375"- .500" .500"- .625" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .500"- .625" .625"- .750" .750"- .875" .875"-1 .000" 1 .000"-1 .125" .750"- .875" .875"-1 .000" 1 .000"-1 .125" 1 .125"-1 .250" 1 .000"-1 .125" 1 .125"-1 .250" 1 .250"-1 .375" 1 .312"-1 .437" 1 .437"-1 .562" 1 .687"-1 .812" 1 .750"-1 .875" ( .63- .79) ( .79- .95) ( .95-1 .11) ( .47- .63) ( .63- .95) ( .95-1 .27) (1 .27-1 .59) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) (2 .86-3 .17) (2 .54-2 .86) (2 .86-3 .17) (3 .17-3 .49) (3 .33-3 .65) (3 .65-3 .97) (4 .28-4 .60) (4 .44-4 .76) Form Size F1 F2 F3 F4 F5 F5 F6 Catalog Number 07401071 07401072 07401073 07401074 07401076 07401078 07401080* 07401081 07401083 07401084* 074011275* 07401085 07401087 07401089 07401091* 074011229* 074011230 07401137 07401108 074011042* 074011045 074011046 074011047 074011233 074011244 074011246 074011234* Kellems(R) Wire Management Products Kellems(R) Wire Management Products Straight Female 90 Male 45 Male Thread N.P.T. Thread Size Inches 1/2 3/4 11/4 .250"- .375" .375"- .500" .500"- .625" .500"- .625" .625"- .750" .750"- .875" .625"- .750" .750"- .875" .875"-1 .000" 1 .000"-1 .125" 1 .125"-1 .250" ( .63- .95) ( .95-1 .27) (1 .27-1 .59) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) (2 .86-3 .17) Form Size F2 F3 F4 F5 Catalog Number 074011236 074011021 074011237* 074011049 074011051* 074011239* 074011055 074011057 074011199* 074011059 074011060 45 Male Note: Kellems(R) Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b). * Cable jacket may have to be stripped to pass through connector body. Dimensions in Inches (cm) www.hubbell-wiring.com T-61 Deluxe Cord GrIps 1 Grip Diameter Range Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Deluxe Cord Grips Nylon Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . Straight Male Thread N.P.T. Thread Size Inches 1/2 3/4 1 Grip Diameter Range Inches (cm) .187"- .250" .250"- .375" .375"- .500" .500"- .625" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .625"- .750" .750"- .875" .875"-1 .000" 1 .000"-1 .125" ( .47- .63) ( .63- .95) ( .95-1 .27) (1 .27-1 .59) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) (2 .54-2 .86) Form Size F2 F3 F4 Catalog Number 074011331 074011332 074011333 074011334* 074011335 074011336 074011337 074011338* 074011341 074011342 074011343 074011344* Straight Male 90 Male Thread N.P.T. Thread Size Inches 1/2 3/4 Grip Diameter Range Inches (cm) .250"- .375" .375"- .500" .500"- .625" .375"- .500" .500"- .625" .625"- .750" ( .63- .95) ( .95-1 .27) (1 .27-1 .59) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) Form Size F2 F3 Catalog Number 074011346 074011347 074011348* 074011349 074011350 074011351* Deluxe Cord Grips 90 Male Note: Kellems(R) Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b). * Cable jacket may have to be stripped to pass through connector body. T-62 www.hubbell-wiring.com Dimensions in Inches (cm) Deluxe Cord Grips Nylon Fittings, Non-metallic Mesh, Liquidtight, for Insulated Cables and Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables Nylon Fittings Non-metallic Mesh, Liquidtight for Insulated Cables Straight Male Thread N.P.T. Thread Size Inches 1/2 3/4 1 Grip Diameter Range Inches (cm) .187"- .250" .250"- .312" .312"- .375" .187"- .250" .250"- .375" .375"- .500" .375"- .500" .500"- .625" .625"- .750" .500"- .625" .625"- .750" .750"- .875" .875"-1 .000" ( .47- .63) ( .63- .79) ( .79- .95) ( .47- .63) ( .63- .95) ( .95-1 .27) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) Form Size F1 F2 F3 F4 WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . Catalog Number CG304NM CG305NM CG306NM CG404NM CG406NM CG408NM CG608NM CG610NM CG612NM CG810NM CG812NM CG814NM CG816NM Kellems(R) Wire Management Products Kellems(R) Wire Management Products Straight Male 90 Male Thread N.P.T. Thread Size Inches Grip Diameter Range Inches (cm) 1/2 .250"- .375" .375"- .500" .375"- .500" .500"- .625" .625"- .750" .625"- .750" .750"- .875" 3/4 1 ( .63- .95) ( .95-1 .27) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .59-1 .90) (1 .90-2 .22) Form Size F2 F3 F4 Catalog Number CG40690NM CG40890NM CG60890NM CG61090NM CG61290NM* CG81290NM CG81490NM 90 Male Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight for Insulated Cables Straight Male Thread N.P.T. Thread Size Inches 1/2 3/4 1 .187"- .250" .250"- .375" .375"- .500" .500"- .625" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .500"- .625" .625"- .750" .750"- .875" .875"-1 .000" ( .47- .63) ( .63- .95) ( .95-1 .27) (1 .27-1 .59) ( .95-1 .27) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) Form Size F2 F2 F3 F4 Catalog Number CG404SST CG406SST CG408SST CG410SST CG608SST CG610SST CG612SST CG614SST CG810SST CG812SST CG814SST CG816SST Straight Stainless Steel Male Note: Kellems(R) Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b). * Cable jacket may have to be stripped to pass through connector body. Dimensions in Inches (cm) www.hubbell-wiring.com T-63 Deluxe Cord GrIps 3/4 Grip Diameter Range Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products PG and Metric Threaded Deluxe Cord Grips Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . Straight PG* Male Thread Cord Diameter Range Inches (cm) Hub Size PG16 PG21 PG21 .500"- .625" .500"- .625" .625"- .750" .750"- .875" .625"- .750" .750"- .875" .875"-1 .000" 1 .125"-1 .250" 1 .125"-1 .250" PG29 PG29 PG36 (1 .27-1 .59) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (1 .59-1 .90) (1 .90-2 .22) (2 .22-2 .54) (2 .86-3 .17) (2 .86-3 .17) Form Size Catalog Number F2 F2 F3 074PG16010 074PG21010 074PG211247 074PG211248 074PG29021 074PG29023 074PG29025 074PG291028** 074PG36028** F4 F5 F5 Note: * Panzergewinde. Straight PG Male Straight Metric Male Thread Cord Diameter Range Inches (cm) Hub Size M20 M25 .500"- .625" .625"- .750" .750"- .875" .500"- .625" .625"- .750" .750"- .875" .875"-1 .000" 1 .125"-1 .250" 1 .000"-1 .125" PG and Metric Threaded Deluxe Cord Grips M25 M32 M32 Straight Metric Male Note: Kellems(R) Deluxe Cord Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code Sections 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b). ** Cable jacket may have to be stripped to pass through connector body. T-64 (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (1 .27-1 .59) (1 .59-1 .90) (1 .90-2 .22) (2 .24-2 .54) (2 .86-3 .17) (2 .54-2 .86) Form Size F2 F3 F2 F4 F5 Catalog Number 074M20010 074M251247 074M251248 074M25017 074M32021 074M32023 074M32025 074M321028 074M321250 Specifications Material Aluminum Stainless Steel (Gotcha Rings) Neoprene (Bushings) Temperature Range -30F to +240F (-34C to +115C) . -30F to +240F (-34C to +115C) . -30F to +240F (-34C to +115C) . Hazardous Locations Suitable for use in hazardous locations per Class I Div . 2, Class II Div . 1 & 2, Class III Div . 1 & 2 N .E .C . Reference 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2) and 503.10(b). Approvals Cord Connectors Deluxe Cord Grips Wet Locations UL Listed in accordance with Standard 514B . UL Control numbers 898D and 899D . Suitable for use in wet locations when used with a listed nylon washer between box and fitting . www.hubbell-wiring.com Dimensions in Inches (cm) Dust-Tight Strain Relief Grips Aluminum Fittings, Galvanized Steel Mesh, for Insulated Cables WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . Non-Insulated, Wide Range Strain Relief Thread Size Cable Diameter Range Inches (cm) Mesh Length @ Nom. Dia. Inches (cm) Catalog Number 1/2 N .P .T . 1/2 N .P .T . 1/2 N .P .T . 3/4 N .P .T . 1 N .P .T . 11/4 N .P .T . PG29* .24"- .32" .32"- .43" .43"- .54" .54"- .73" .73"- .97" .97"-1 .25" .73"- .97" 3 .25" (8 .25) 3 .75" (9 .52) 4 .75" (12 .06) 6 .5" (16 .51) 7" (17 .78) 9" (22 .86) 7" (17 .78) 073031200 073031201 073031202 073031203 073031204 073031205 073PG291204 ( .61- .81) ( .81-1 .09) (1 .09-1 .37) (1 .37-1 .85) (1 .85-2 .46) (2 .46-3 .17) (1 .85-2 .46) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: * Panzergewinde. Non-Insulated Insulated, Wide Range Strain Relief with Insulating Bushing Thread Size Cable Diameter Range Inches (cm) Mesh Length @ Nom. Dia. Inches (cm) 1/2 N .P .S . 1/2 N .P .S . 1/2 N .P .S . 3/4 N .P .S . 1 N .P .S . 11/4 N .P .S . 11/2 N .P .T . 2 N .P .T . 21/2 N .P .T . 21/2 N .P .T . .24"- .32" ( .61- .81) .32"- .43" ( .81-1 .09) .43"- .54" (1 .09-1 .37) .54"- .73" (1 .37-1 .85) .73"- .97" (1 .85-2 .46) .97"-1 .25" (2 .46-3 .17) 1 .25"-1 .50" (3 .17-3 .81) 1 .50"-1 .70" (3 .81-4 .32) 1 .70"-2 .00" (4 .32-5 .08) 2 .00"-2 .45" (5 .08-6 .22) 3 .25" (8 .25) 3 .75" (9 .52) 4 .75" (12 .06) 6 .5" (16 .51) 7" (17 .78) 9" (22 .86) 11 .75" (29 .84) 13 .25" (33 .65) 13 .5" (34 .29) 13 .75" (34 .92) Dim. A In. (cm) Min. Space Between Grips In. (cm) Catalog Number 1" (2 .54) 1" (2 .54) 1" (2 .54) 1" (2 .54) 1 .313" (3 .02) 1 .313" (3 .02) 1 .313" (3 .02) 1 .375" (3 .49) 1 .5" (3 .81) 1 .5" (3 .81) 1 .25" (3 .17) 1 .25" (3 .17) 1 .25" (3 .17) 1 .5" (3 .81) 1 .75" (4 .44) 2 .25" (5 .71) 2 .5" (6 .35) 3 .25" (8 .25) 3 .625" (9 .21) 3 .625" (9 .21) 073031206 073031207 073031208 073031209 073031210 073031211 073031212 073031213 073031214 073031215 Insulated Dust-Tight Strain Relief Grips Dimensions in Inches (cm) www.hubbell-wiring.com T-65 Kellems(R) Wire Management Products Kellems(R) Wire Management Products I-Grips Plastic-Coated, Galvanized Steel Mesh for Insulated Cables WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-71 through T-76 . Application Kellems(R) I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip(R) plugs and connector bodies . The eye tabs fit under the nylon cord clamp and the screws slide through the eyelets, securing the grip in place . These grips are for indoor use only . Benefits * Easily attached to Insulgrip plugs and connector bodies. * Controls cable arc-of-bend. * Provides heavy-duty strain relief. * Fits all sizes. I-Grips Cable Diameter Range Inches (cm) E Inches (cm) M Inches (cm) Catalog Number .32"- .43" .43"- .56" .56"- .73" .73"- .85" .85"-1 .00" 1 .00"-1 .25" 1 .25" (3 .17) 1 .25" (3 .17) 1 .50" (3 .81) 1 .50" (3 .81) 1 .50" (3 .81) 1 .50" (3 .81) 4" (10 .16) 4 .75" (12 .06) 6" (15 .24) 6 .5" (16 .51) 8" (20 .32) 10" (25 .40) 07310001 07310002 07310003 07310004 07310005 07310006 ( .81-1 .09) (1 .09-1 .42) (1 .42-1 .85) (1 .85-2 .16) (2 .16-2 .54) (2 .54-3 .17) I-Grips Note: E-Eye length. M-Mesh length at nominal diameter. Eyelet hole diameter .203" (.52cm). I-Grips should not be used on Insulgrip devices when "Seal-Tite(R)" weatherproof covers are to be installed. T-66 www.hubbell-wiring.com Dimensions in Inches (cm) Thread Adapters for Multi-Pin Connectors Aluminum Thread Adapters for Multi-Pin Connectors Kellems(R) Thread Adapters are devices formatting AN-MS connectors and other multi-pin connectors to Kellems grips with N .P .T . threaded fittings . They are made of aluminum with internal threads and replace the connector cord clamp . These adapters permit the installation of Kellems Grips, to prevent cable or conduit pull-out and control arc-of-bend . Applications Thread adapters allow the installation of Kellems(R) Grips on multi-pin connectors at electrical consoles, mobile equipment, control switches, assembly equipment and testing machines . Benefits * Easy installation. * Allows the use of Kellems grips. * Extends connector and cable life. Thread Adapters for Multi-Pin Connectors Thread Adapters AN-MS Connector Size** Deluxe Cord Grips AN-MS N.P.T. Cable Clamp Thread Thread Catalog Number*** Size A in. Size B in. Number Cable Diameter Range Inches (cm) Liquidtight Conduit Grips (Insulated Throat) Strain Relief Grips Catalog Number Cable Diameter Range Inches (cm) Catalog Number Catalog Number 091041000 .250"- .312" ( .63- .79) 091041001 .312"- .375" ( .79- .95) 091041002 .375"- .437" ( .95-1 .11) 07401001 07401002 07401003 091041003 .187"- .250" ( .47- .63 091041004 .250"- .375" ( .63- .95) 091041006 .375"- .500" ( .95-1 .27) .500"- .625" (1 .27-1 .59) 07401004 .24"- .32" ( .61- .81) 073031200 -- 07401006 .32"- .43" ( .81-1 .09) 073031201 074093512 07401008 .43"- .54" (1 .09-1 .37) 073031202 -- 07401010* " x 20" 1" x 20" 3/4 1" x 18" 091041005 .187"- .250" ( .47- .63) 091041007 .250"- .375" ( .63- .95) 091041008 .375"- .500" ( .95-1 .27) .500"- .625" (1 .27-1 .59) .625"- .750" (1 .59-1 .90) 07401011 07401013 07401015 07401017 07401018 3057-12 3057-16 3057-20 3057-24 1" x 18" 1" x 18" 13/4" x 18" 1 2" x 18" 091041009 091041010 091041012 091041015 074011195 07401019 07401021 .73"- .97" (1 .85-2 .46) 073031204 074093514 07401023 07401025 24, 28 32 36 3057-16 3057-20 3057-24 1" x 18" 13/4" x 18" 11/4 2" x 18" 091041011 .750"- .875" (1 .90-2 .22) 091041013 .875"-1 .000" (2 .22-2 .54) 091041016 1 .000"-1 .125" (2 .54-2 .86) 1 .125"-1 .375" (2 .86-3 .17) 32 36 40 3057-20 3057-24 3057-28 13/4" x 18" 2" x 18" 11/2 21/4" x 16" 091041014 .875"-1 .000" (2 .22-2 .54) 07401029 091041017 1 .000"-1 .125" (2 .54-2 .86) 07401030 091041019 1 .125"-1 .250" (2 .86-3 .17) 07401031 1 .250"-1 .375" (3 .17-3 .49) 07401032 1/2" x 28" " x 24" 3/4" x 20" 14, 14S 16, 16S 18 3057-6 3057-8 3057-10 3/4" x 20" " x 20" 1" x 20" 1/2 16, 16S 18 20, 22 3057-8 3057-10 3057-12 20, 22 24, 28 32 36 .375"- .500" ( .95-1 .27) .500"- .625" (1 .27-1 .59) .625"- .750" (1 .59-1 .90) .750"- .875" (1 .90-2 .22) .875"-1 .000" (2 .22-2 .54) .54"- .74" (1 .37-1 .85) 073031203 074093513 074011251 07401026 07401027 .97"-1 .25" (2 .46-3 .17) 073031205 074093515 07401028 -- 074093516 Note: * Cable jacket may have to be stripped to pass through connector body. ** Number stamped on connector shell. *** Number stamped on clamp shell. Example Thread Adapter 091041006 Dimensions in Inches (cm) www.hubbell-wiring.com T-67 Thread Adapters for Multi-Pin Connectors 8S, 10S 3057-3 10SL, 12, 12S 3057-4 14, 14S 3057-6 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Strain Relief for Liquidtight Conduit Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit and PolyTuff I Non-Metallic Conduit WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-77, T-79 and T-80 . Benefits * Helps prevent conduit pull-out and damage at the fitting. * Reduces equipment downtime. Straight With Male Fitting Conduit Trade Size Inches Straight with Male Fitting N.P.T. Fitting Size Inches Mesh Length Inches (cm) Catalog Number (Insulated) Catalog Number (Non-insulated) 1/2 3" (7 .62) 074093511 074093401 1/2 1/2 3 .5" (8 .89) 074093512 074093402 3/4 3/4 4" (10 .16) 074093513 074093403 1 1 5" (12 .70) 074093514 074093404 11/4 11/4 6" (15 .24) 074093515 074093405 11/2 11/2 6 .75" (17 .14) 074093516 074093406 2 2 8" (20 .32) 074093518 074093408 21/2 21/2 9 .75" (24 .76) 074093520 074093410 074093412 3 3 11" (27 .94) 074093522 4 4 14" (35 .56) 074093526 -- 90 Angle With Male Fitting Strain Relief for Liquidtight Conduit Conduit Trade Size Inches 90 Angle with Male Fitting T-68 N.P.T. Fitting Size Inches Mesh Length Inches (cm) Catalog Number (Insulated) Catalog Number (Non-insulated) 1/2 3" (7 .62) 074093541 074093421 1/2 1/2 3 .5" (8 .89) 074093542 074093422 3/4 3/4 4" (10 .16) 074093543 074093423 1 1 5" (12 .70) 074093544 074093424 11/4 11/4 6" (15 .24) 074093545 074093425 11/2 11/2 6 .75" (17 .14) 074093546 074093426 2 2 8" (20 .32) 074093548 074093428 21/2 21/2 9 .75" (24 .76) 074093550 -- 3 3 11" 074093552 -- (27 .94) Note: For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. www.hubbell-wiring.com Dimensions in Inches (cm) Strain Relief for Liquidtight Conduit Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit and PolyTuff I Non-Metallic Conduit Straight With Chase Fitting Conduit Trade Size Inches N.P.T. Fitting Size Inches Mesh Length Inches (cm) Catalog Number 1/2 1/2 3 .5" (8 .89) 07406079 3/4 3/4 4" (10 .16) 07406080 1 1 5" (12 .70) 07406081 11/4 11/4 6" (15 .24) 07406082 11/2 11/2 6 .75" (17 .14) 07406083 WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-77, T-79 and T-80 . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Straight with Chase Connector 45 Angle With Male Fitting Conduit Trade Size Inches N.P.T. Fitting Size Inches Mesh Length Inches (cm) Catalog Number (Insulated) Catalog Number (Non-insulated) 1/2 3" (7 .62) 074093561 074093441 1/2 1/2 3 .5" (8 .89) 074093562 074093442 3/4 3/4 4" (10 .16) 074093563 074093443 1 1 5" (12 .70) 074093564 074093444 11/4 11/4 6" (15 .24) 074093565 074093445 11/2 11/2 6 .75" (17 .14) 074093566 074093446 2 2 8" 074093568 074093448 (20 .32) 45 Angle with Male Fitting Dimensions in Inches (cm) www.hubbell-wiring.com T-69 Strain Relief for Liquidtight Conduit Note: For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. Kellems(R) Wire Management Products Kellems(R) Wire Management Products Strain Relief for Liquidtight Conduit Steel Fitting, Stainless Steel Mesh for UL Type A Liquidtight Conduit WARNING! It is important that you read all breaking strength, safety and technical data relating to this product on pages T-78 through T-80 . Straight Male Hubbell Fitting Conduit Trade Size Inches N.P.T. Fitting Size Inches Mesh Length Inches (cm) Catalog Number 1/2 3 .75" (9 .52) H038CNK 1/2 1/2 4 .5" (11 .43) H050CNK 3/4 3/4 6 .25" (15 .87) H075CNK 1 1 7 .5" (19 .05) H100CNK 11/4 11/4 9" (22 .86) H125CNK 11/2 11/2 13 .5" (34 .29) H150CNK 2 2 14 .5" (36 .83) H200CNK Straight Male with Fitting 90 Male Hubbell Fitting N.P.T. Fitting Size Inches Mesh Length Inches (cm) Catalog Number 1/2 3 .75" (9 .52) H0389CNK 1/2 1/2 4 .5" (11 .43) H0509CNK 3/4 3/4 6 .25" (15 .87) H0759CNK 1 1 7 .5" (19 .05) H1009CNK 11/4 11/4 9" (22 .86) H1259CNK 11/2 11/2 13 .5" (34 .29) H1509CNK 2 2 14 .5" (36 .83) H2009CNK Strain Relief for Liquidtight Conduit 90 Angle Conduit Trade Size Inches T-70 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Strain Relief Grips Kellems Strain Relief Grips are designed to prevent tension from being transmitted to joints and terminals on electrical cord, cable and conduit . In most applications, a Kellems grip for strain relief is stronger than the cable itself and gives much greater security than the use of a fitting alone . Kellems Grips for strain relief help make electrical systems safer, and save money by minimizing downtime from costly electrical failure due to cable pull-out . Kellems Grips also aid in compliance with the National Electric Code's terminal tension protection requirements . Select the Correct Grip for Strain Relief Kellems Grips for strain relief are designed to fit on electrical cord, cable or flexible conduit . Step 1 Refer to the chart below to determine the grip style best suited for your application . Step 2 Determine your cable outside diameter or conduit size . Step 3 Locate environment--indoors or outdoors . Step 4 Decide if a liquidtight seal is required . Step 5 Select N .P .T . size and fitting style . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Strain Relief System Selection Chart Type Fitting or Attachment Page Number Aluminum fittings, stainless steel mesh, neoprene oil-andwatertight bushing . Double-single weave . .187"-3 .250" ( .47-8 .25) N .P .T ., PG, and metric aluminum, male straight, 45 male, 90 male, female straight . Thread sizes "-3" . T-60, T-61, T-64 Outdoors or indoors where subjected to moisture or splash . Examples are marine and food processing equipment . Nylon fitting, stainless steel mesh, double-single weave, neoprene oil-andwatertight bushing . .187"-1 .125" ( .47-2 .86) N .P .T . nylon, male straight, 90 male . Thread sizes 1/2"-1" . T-62 Deluxe Cord Nylon Fitting/ Non-metallic Grip Indoor or outdoors . Provides liquidtight seal, where exposed to moisture . Excellent for oil refining and chemical processing . Non-metallic grip is corrosion resistant, nonconductive and provides superior gripping and flexing benefits . Neoprene liquidtight bushing . Nylon fitting . .187"-1 .000" ( .47-2 .54) N .P .T . nylon, straight male, T-63 thread sizes "-1" 90 male, thread sizes 1/2"-1" . Deluxe Cord Stainless Steel Fitting And Grip Indoor or outdoor use where exposed to moisture . Very strong for heavy abuse areas such as drilling platforms, steel mills and mines . Stainless steel fitting and grip for strength . Neoprene liquidtight bushing . Double/single weave grip . .187"-1 .000" ( .47-2 .54) Straight male Only with N .P .T . Thread sizes 1/2"-1" . T-63 Dust-Tight Strain Relief Indoor use only for wiring of electrical enclosures, machine tools, portable power tools, bus drop cable systems . Neoprene gasket-seals .240"-2 .450" out chips, dirt, dust . ( .61-6 .22) One piece design with galvanized steel mesh . Insulating bushing available . Zinc-plated steel locknut . Straight male N .P .S . or N .P .T . T-65 Liquidtight Flexible Conduit Grip (Metal and Non-Metallic) Wiring of machine tools, electrical enclosures, motors and systems where metallic liquidtight flexible conduit is subjected to vibration, flexure, motion or strain . Stainless steel mesh, liquidtight fittings . Sealing "O" rings (optional) . Choice of fittings . .375"-4 .000" trade sizes N .P .T . 1/2"-4", Hubbell fittings, Male straight, 45 male, 90 male, female straight . T-68, T-69 Liquidtight Flexible Conduit Grip (UL Type A) Wiring or machine tools, electrical enclosures, motors and systems where conduit is subject to vibration and strain . Stainless steel mesh, liquidtight fittings with "O" ring and locknut . .375"-2 .008" trade size male N .P .T . steel, Hubbell fittings, straight male, 90 Thread sizes 1/2"-2" . T-70 Application Features Deluxe Cord Aluminum Fitting/ Stainless Steel Grip Outdoors or indoors where subjected to moisture or splash . Examples are crane and hoist pendant drop stations, hand tools, pumps and processing equipment . Deluxe Cord Nylon Fitting/ Stainless Steel Grip Dimensions in Inches (cm) www.hubbell-wiring.com T-71 Technical Information Cord or Conduit Range Inches (cm) Grip Type Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Strain Relief Grips Wire Mesh Grip Materials Material Galvanized steel wire Stainless steel wire (302/304) Non-metallic strand Features * High strength * Not subject to continuous outside environment * High strength * Corrosion resistant * Slightly magnetic Product Group * Strain relief grips * I-Grips * Deluxe cord grips * Liquidtight, flexible, metal conduit grips * UL type A conduit grips * Superior flex life * Non-conductive * Corrosion resistant * Moderate strength * Non-metallic deluxe cord grips Operating Temperatures Material Temperature Range Aluminum -40F to +300F (-40C to +149C) . Aluminum Deluxe Cord Grips -30F to +240F (-34C to +115C) . Non-Metallic Deluxe Cord Grips -30F to +225F (-34C to +107C) . Nylon -40F to +225F (-40C to +107C) . Nylon Fitting with Stainless Steel Mesh -40F to +225F (-40C to +107C) . Stainless Steel -60F to +1000F (-51C to +537C) . Stainless Steel Deluxe Cord Grips -30F to +240F (-34C to +115C) . Neoprene (Bushings) -30F to +240F (-34C to +115C) . Hazardous Locations Product Categories The product categories listed to the right are suitable for use in hazardous locations per Class I Div . 2, Class II Div . 1 & 2, Class III Div . 1 & 2 . Deluxe cord grip, aluminum fitting; Deluxe cord grip, nylon fitting; Deluxe cord grip, non-metallic; Sealtite conduit grips; Dustight strain relief grips . Flammability Non-metallic deluxe cord grips will not support combustion . Listed below are the ratings . Component Rating Mesh grip UL 94HB . Fitting UL 94V-2 . Approvals Technical Information UL Listing and CSA Certification are indicated on appropriate product catalog pages . Agency UL Control Number Underwriters Laboratories Inc . 898D and 899D . Wet Locations Product Categories The products noted to the right are suitable for use in wet locations when a listed sealing ring is used between box and fitting . T-72 Deluxe cord grip, aluminum fitting; Deluxe sealing ring cord grip; Deluxe cord grip, non-metallic; Sealtite conduit grips; Hubbell non-metallic conduit grips; Cord connectors; Hubbell Juniors; PolyTuff(R) connectors; Hubbell sealtite conduit connectors . www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Strain Relief Grips Form Size Definition The term "Form Size" refers to the physical mass or overall dimensions of a cord connector . Form 1 is the smallest size, Form 8 is the largest size . Knockout Holes N.P.T. Hub Size Inches Knockout Hole Recommended Min. to Max. Inches (cm) 1/4 .540" to .570" (1 .37-1 .45) .671" to .701" (1 .70-1 .78) 1/2 .859" to .906" (2 .18-2 .30) 3/4 1 .094" to 1 .141" (2 .78-2 .90) 1 1 .359" to 1 .406" (3 .45-3 .57) 11/4 1 .719" to 1 .766" (4 .37-4 .49) 11/2 1 .969" to 2 .016" (5 .00-5 .12) 2 2 .453" to 2 .500" (6 .23-6 .35) 21/2 2 .953" to 3 .000" (7 .50-7 .62) 3 3 .578" to 3 .625" (9 .09-9 .21) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Product Data Deluxe Cord Grips, Liquidtight for Insulated Cables Deluxe Cord Grips helps to alleviate pull tension on terminals, control cable arc-of-bend, prevent cord pullout, and provide a liquidtight seal . They are offered with either aluminum, stainless steel or nylon fittings in a variety of configurations and N .P .T . thread sizes . Additionally, a completely non-metallic product is offered on page T-63 . Application Deluxe Cord Grips are used indoors or outdoors to help prevent cord pull-out, and where cables are subjected to moisture, splash or submersion . Specific uses are: wiring enclosures, pendant stations, hand tools, construction, processing and material handling equipment, pumps, motors and machine tools . Benefits Dimensions in Inches (cm) www.hubbell-wiring.com Technical Information * Helps to prevent cable pull-out. * Controls cable arc-of-bend. * Provides a liquidtight seal. * Corrosion resistant stainless steel mesh with aluminum collar. T-73 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Strain Relief Grips Deluxe Cord Grips Fitting Dimensions Straight Hubbell Connectors F N.P.T. (Inches) Aluminum, Inches (cm) A B C Form D E Throat Dia. A/C* A/F* Nylon, Inches (cm) A B C Dia. Ref. .88" (2 .24) .90" (2 .29) .46" .44" (1 .17) (1 .12) .99" .88" (2 .51) (2 .24) 1 .00" 1 .10" .43" .45" 1 .00" .93" (2 .54) (2 .79) (1 .09) (1 .14) (2 .54) (2 .36) 1 .01" .88" .90" .46" .45" .87" .75" (2 .57) (2 .24) (2 .29) (1 .17) (1 .14) (2 .21) (1 .90) 1/2-14 1 .88" (2 .24) .90" (2 .29) .46" .44" (1 .17) (1 .12) 1 .00" .88" (2 .54) (2 .24) 1 .00" 1 .10" .46" .45" 1 .00" .93" (2 .54) (2 .79) (1 .17) (1 .14) (2 .54) (2 .36) -- 1/2-14 2 1 .13" (2 .87) 1 .10" (2 .79) .55" .64" (1 .40) (1 .63) 1 .11" 1 .00" (2 .82) (2 .54) 1 .32" 1 .50" .53" .58" 1 .25" 1 .12" (3 .35) (3 .81) (1 .35) (1 .47) (3 .17) (2 .84) 1 .30" 1 .13" 1 .10" .54" .63" 1 .16" 1 .00" (3 .30) (2 .87) (2 .79) (1 .37) (1 .60) (2 .95) (2 .54) 1/2-14 3 1 .38" (3 .51) 1 .50" (3 .81) .55" .64" (1 .40) (1 .63) 1 .40" 1 .25" (3 .56) (3 .17) -- -- -- -- -- -- -- -- -- -- -- -- -- 3/4-14 2 1 .13" (2 .87) 1 .10" (2 .79) .55" .64" (1 .40) (1 .63) 1 .29" 1 .13" (3 .28) (2 .87) -- -- -- -- -- -- -- -- -- -- -- -- -- 3/4-14 3 1 .38" (3 .51) 1 .50" (3 .81) .55" .82" (1 .40) (2 .08) 1 .40" 1 .25" (3 .56) (3 .17) 1 .56" 1 .60" .55" .77" 1 .44" 1 .31" (3 .96) (4 .06) (1 .40) (1 .96) (3 .66) (3 .33) 1-111/2 3 -- -- -- -- 1-111/2 4 1 .75" (4 .44) 1 .60" (4 .06) .71" 1 .02" (1 .80) (2 .59) 1 .81" 1 .62" (4 .60) (4 .11) 1 .88" 1 .75" .70" 1 .01" 1 .84" 1 .63" (4 .78) (4 .44) (1 .78) (2 .57) (4 .67) (4 .14) 2 .02" 1 .75" 1 .40" .70" 1 .03" 1 .88" 1 .63" (5 .13) (4 .44) (3 .56) (1 .78) (2 .62) (4 .78) (4 .14) 1-111/2 5 2 .31" (5 .87) 1 .70" (4 .32) .66" 1 .01" (1 .68) (2 .57) 2 .28" 2 .00" (5 .79) (5 .08) -- -- -- -- -- -- -- -- -- -- -- -- -- 11/4-111/2 5 2 .31" (5 .87) 1 .70" (4 .32) .74" 1 .26" (1 .88) (3 .20) 2 .28" 2 .12" (5 .79) (5 .38) -- -- -- -- -- -- -- -- -- -- -- -- -- 11/2-11 5 2 .31" (5 .87) 1 .70" (4 .32) .74" 1 .38" (1 .88) (3 .51) 2 .28" 2 .12" (5 .79) (5 .38) -- -- -- -- -- -- -- -- -- -- -- -- -- 11/2-111/2 6 3 .00" (7 .62) 2 .20" (5 .59) .75" 1 .50" (1 .90) (3 .81) 2 .97" 2 .75" (7 .54) (6 .98) -- -- -- -- -- -- -- -- -- -- -- -- -- 2-111/2 6 3 .00" (7 .62) 2 .20" (5 .59) .80" 1 .92" (2 .03) (4 .88) 3 .24" 3 .00" (8 .24) (7 .62) -- -- -- -- -- -- -- -- -- -- -- -- -- 2-111/2 7 3 .85" (9 .78) 2 .70" (6 .86) .88" 1 .94" (2 .24) (4 .93) 4 .05" 3 .75" (10 .29) (9 .52) -- -- -- -- -- -- -- -- -- -- -- -- -- 21/2-8 7 3 .85" (9 .78) 2 .70" (6 .86) 1 .30" 2 .32" (3 .30) (5 .89) 4 .34" 4 .02" -- (11 .02) (10 .21) -- -- -- -- -- -- -- -- -- -- -- -- 21/2-8 8 4 .75" 2 .70" (12 .06) (6 .86) 1 .25" 2 .38" (3 .17) (6 .05) 4 .86" 4 .50" -- (12 .34) (11 .43) -- -- -- -- -- -- -- -- -- -- -- -- 3-8 7 3 .85" (9 .78) 2 .70" (6 .86) 1 .30" 2 .54" (3 .30) (6 .45) 4 .34" 4 .01" -- (11 .02) (10 .21) -- -- -- -- -- -- -- -- -- -- -- -- 3-8 8 4 .50" 2 .70" (11 .43) (6 .86) 1 .38" 3 .00" (3 .51) (7 .62) 4 .86" 4 .50" -- (12 .34) (11 .43) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- A/F* -- A/C* A/F D E Throat Dia. A/C* A/F* 1 -- Ref. Stainless Steel, Inches (cm) A B C -18 -- Dia. D E Throat Dia. A/C* -- -- -- -- -- -- 1 .59" 1 .38" 1 .30" .56" .81" 1 .44" 1 .25" (4 .04) (3 .51) (3 .30) (1 .42) (2 .06) (3 .66) (3 .17) -- -- -- -- -- -- -- Technical Information Note: *A/C-- Across Corners; A/F--Across Flats. A (Overall) B Ref. E F C D T-74 Dimensions shown are approximate and are subject to change without notice. www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Strain Relief Grips Deluxe Cord Grips Fitting Dimensions 45 Hubbell Connectors Aluminum, Inches (cm) F N.P.T. (Inches) Form 1/2-14 2 3/4-14 3 1-111/2 4 11/4-111/2 5 11/2-111/2 5 A B Ref Ref 2 .00" (5 .08) 2 .30" (5 .84) 2 .60" (6 .60) 3 .90" (9 .91) 3 .90" (9 .91) 1 .90" (4 .83) 2 .50" (6 .53) 2 .80" (7 .11) 3 .90" (9 .91) 3 .90" (9 .91) C D Throat Dia. E Across Comers Across Flats .550" (1 .40) .560" (1 .42) .700" (1 .78) .740" (1 .88) .740" (1 .88) .560" (1 .42) .750" (1 .90) 1 .000" (2 .54) 1 .250" (3 .17) 1 .500" (3 .81) 1 .270" (3 .23) 1 .480" (3 .76) 1 .690" (4 .29) 2 .45" (6 .22) 2 .45" (6 .22) 1 .110" (2 .79) 1 .281" (3 .25) 1 .500" (3 .81) 2 .125" (5 .40) 2 .125" (5 .40) C D Throat Dia. E A/C* A/F* Dia. .460" (1 .17) .500" (1 .27) .560" (1 .42) .700" (1 .78) .730" (1 .85) .750" (1 .92) .800" (2 .03) .440" (1 .12) .546" (1 .39) .765" (1 .94) 1 .000" (2 .54) 1 .260" (3 .20) 1 .500" (3 .81) 1 .920" (4 .88) 1 .15" (2 .92) 1 .30" (3 .30) 1 .49" (3 .78) 1 .70" (4 .32) 2 .47" (6 .27) 2 .47" (6 .27) 2 .98" (7 .57) 1 .10" (2 .79) 1 .13" (2 .87) 1 .31" (3 .33) 1 .50" (3 .81) 2 .15" (5 .46) 2 .15" (5 .46) 2 .78" (7 .06) .875" (2 .22) 1 .125" (2 .86) 1 .375" (3 .49) 1 .750" (4 .44) 2 .310" (5 .87) 2 .310" (5 .87) 3 .000" (7 .62) B Ref. G G Dia. 1 .125" (2 .86) 1 .375" (3 .49) 1 .750" (4 .44) 2 .310" (5 .87) 2 .310" (5 .87) A Ref. E C F D 90 Hubbell Connectors Aluminum, Inches (cm) F N.P.T. (Inches) A Form -18 1 1/2-14 2 3/4-14 3 1-111/2 4 11/4-111/2 5 11/2-111/2 5 2-111/2 6 B Ref 1 .27" (3 .23) 1 .56" (3 .96) 1 .79" (4 .55) 2 .08" (5 .28) 3 .18" (8 .08) 3 .18" (8 .08) 3 .51" (8 .92) 2 .00" (5 .08) 2 .30" (5 .84) 2 .80" (7 .11) 3 .20" (8 .13) 4 .30" (10 .92) 4 .30" (10 .92) 5 .50" (13 .97) Nylon, Inches (cm) G A B C Dia. D Throat A/C* Ref -- -- 1 .41" (3 .58) 1 .65" (4 .19) 1 .99" (5 .05) -- E G A/F Dia. -- -- -- -- -- 2 .50" (6 .35) 2 .81" (7 .14) 3 .30" (8 .38) -- .550" (1 .40) .560" (1 .42) .700" (1 .78) -- .575" (1 .46) .765" (1 .94) 1 .010" (2 .57) -- 1 .23" (3 .12) 1 .42" (3 .61) 1 .82" (4 .62) -- 1 .12" (2 .82) 1 .29" (3 .28) 1 .60" (4 .06) -- 1 .315" (3 .34) 1 .560" (3 .96) 1 .875" (4 .76) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Note: *A/C - Across Corners; A/F - Across Flats. B Ref. A E C F D Dimensions shown are approximate and are subject to change without notice. Dimensions in Inches (cm) www.hubbell-wiring.com T-75 Technical Information G Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Strain Relief Grips Deluxe Cord Grips Fitting Dimensions Female Hubbell Connectors A (Overall) Aluminum Inches (cm) F N.P.T. Form -18 1 1/2-14 2 3/4-14 2 1-111/2 4 11/4-111/2 5 11/2-111/2 5 B Ref. E D F C (N.P.T. Thread Depth) A B Dia. Ref .88" (2 .24) 1 .13" (2 .87) 1 .13" (2 .87) 1 .75" (4 .44) 2 .31" (5 .87) 2 .31" (5 .87) 1 .40" (3 .56) 1 .80" (4 .57) 2 .10" (5 .33) 2 .30" (5 .84) 2 .80" (7 .11) 2 .80" (7 .11) C D Throat Dia. Across Corners .560" (1 .42) .560" (1 .42) .750" (1 .90) .880" (2 .24) .950" (2 .41) .950" (2 .41) .44" (1 .12) .63" (1 .60) .63" (1 .60) 1 .10" (2 .79) 1 .43" (3 .63) 1 .43" (3 .63) .94" (2 .39) 1 .15" (2 .92) 1 .44" (3 .66) 1 .88" (4 .78) 2 .64" (6 .71) 2 .64" (6 .71) E Across Flats .81" (2 .06) 1 .00" (2 .54) 1 .25" (3 .17) 1 .63" (4 .14) 2 .29" (5 .82) 2 .29" (5 .82) Product Data Dust-Tight Strain Relief Grips for Insulated Cables Kellems Strain Relief Grips connect flexible cord or bus drop cable to electrical enclosures . For indoor use only, they are available with either insulated or noninsulated aluminum fittings, and feature single weave, galvanized steel mesh grips with patented wide range mesh construction . They come with a locknut and a neoprene gasket that provides a dust tight seal . Application Used to connect electrical cable to power boxes, cabinets, panel boards, power centers, machine tools and with bus drop systems . Benefits * Helps prevent cord or cable pull-out. * Provides a dust tight seal. * Easy installation. * Patented mesh construction. * One piece design. I-Grips for Insulated Cables Kellems I-Grips are made of high strength, plastic coated galvanized steel strand . They are offered in six sizes to fit all cable diameters used with Hubbell Insulgrip(R) Kellems l-Grips will control cable arc-of-bend and reduce high pull tensions from being transmitted to the wiring terminals . Application Technical Information Kellems I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip plugs and connector bodies . The eye tabs fit under the nylon cord clamp and the screws slide through the eyelets, securing the grip in place . I-Grips can be used on any Insulgrip cord set which requires cable, arc-of-bend control or heavy duty strain relief . Cord sets used at in-door construction sites or for plant maintenance jobs are examples . These grips are for indoor use only . Benefits * Easily attached to Insulgrip plugs and connector bodies. * Fits all sizes. * Provides heavy duty strain relief. * Controls cable arc-of-bend. Note: I-Grips should not be used on Insulgrip devices when "Seal-Tite(R)" weatherproof covers are to be installed. Dimensions shown are approximate and are subject to change without notice. T-76 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Strain Relief for Liquidtight Conduit Strain Relief Grips for Liquidtight Flexible Metal and PolyTuff I Non-Metallic Conduit Kellems Liquidtight, Flexible Metal Conduit Grips are offered with high quality Hubbell plated steel fittings in a wide variety of N .P .T . sizes and configurations, either insulated or non-insulated . The addition of a stainless steel mesh to these fittings makes them stronger than the conduit itself . Kellems Conduit Grips helps prevent conduit pull-out from the connecting fitting that is subject to stress, pull tension, vibration, motion or strain . They promote safe electrical systems and reduce equipment downtime . Application Kellems Conduit Grips are used in the wiring of machine tools, motors, molding equipment, transformers, weaving and paper machines, fans, lighting, bakeries, breweries, food processing, chemical plants, dairies, mines and any application that requires Liquidtight Conduit . Benefits * Helps prevent conduit pull-out and damage at the fitting. Kellems(R) Wire Management Products Kellems(R) Wire Management Products * Reduces equipment downtime. * Liquidtight fittings. * Easily installed. * Stainless steel grip resists corrosion. Kellems Conduit Grips are suitable for use in hazardous locations per Class I Div . 2, Class II Div . 1 & 2, Class III Div . 1 & 2 of the National Electric Code . Connectors with insulated throats protect insulation on wires during wire pulling . Yellow color easily seen by inspectors . 21/2" - 4" sizes include insulating bushing instead of fixed insulator Nylon gland ring is split for ease of installation and greater compression . Reversible design cannot be installed facing the wrong way . Nylon is impervious to liquids, resistant to temperature extremes and resists abrasion Steel grounding ferrule easily threaded by hand . Fits convolutions to conduit . Eliminates pullouts and insures continuity of ground; distortion free to remain reusable Optional Sealing Washer gives better liquidtight protection around knockout of sheet metal box . Neoprene gasket seals out liquids and steel retaining ring protects gasket from distortion; order separately Body is virtually unbreakable . Straight connectors through 1" are screw machine steel; other sizes malleable iron . Threads at left are tapered to insure liquidtight seal in threaded hub . Liquidtight conduit cutaway view shows flexible steel core under plastic jacket Dimensions in Inches (cm) www.hubbell-wiring.com Hexagonal compression nut is screw machined steel through 1" and malleable iron on larger sizes Wire mesh grip prevents pullout Liquidtight conduit cutaway view shows flexible steel core under plastic jacket T-77 Technical Information Hardened Steel Locknut has tangs that dig into box for excellent continuity of ground; locknut will not slip or spin Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Strain Relief for Liquidtight Conduit Strain Relief for UL Type A, Flexible, Liquidtight Conduit Kellems Grips for UL Type A, non-metallic, flexible, liquidtight conduit are available in straight and 90 male and feature a high quality Hubbell plated steel or malleable iron fitting, complete with a sealing O-ring, lock nut and stainless steel mesh . These grips increase the retention of the conduit in the fitting, control its arc-of-bend and provide a liquidtight seal . Application These grips are used on UL Type A non-metallic conduit connections at limit switches, motor boxes, panel boards, control stations and on all types of machinery and machine tools . Benefits * * * * Provides a liquidtight seal. Helps prevent conduit pull-out. Reduces conduit cutting, kinking, fraying and splitting at the fitting. Easily installed. Steel Locknut has tangs that dig into box for excellent continuity of ground; locknut will not slip or spin Neoprene O-ring is factory assembled into the body to seal out liquids Body is virtually unbreakable . Straight connectors through 1" are screw machine steel; other sizes are malleable iron . Threads are tapered to insure liquidtight seal when used in threaded hub; octagonal shape inside holds the ferrule to prevent conduit from twisting during installation Technical Information Wire mesh grip prevents pullout Insulated throat protects insulation on wires during pulling; yellow color easily seen by inspectors Yellow nylon ferrule fits inside nonmetallic conduit to hold the shape; barb in designed to assure liquidtight seal even with non-square cut; ferrule is keyed to fit into body to prevent conduit twisting Hexagonal compression nut is machine steel through 1" malleable iron on larger sizes; tapered interior compresses sleeve over conduit sealing out liquids and preventing pullout Yellow nylon sleeve installs over conduit; six slits in sleeve permit tight compression onto conduit as compression nut is tightened T-78 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Strain Relief for Liquidtight Conduit Liquidtight Conduit Grip Fitting Dimensions-Inches 45 Angle with Male Fitting E A/C A/F Dimensions D Throat Dia. C A Ref. Trade H Size B Ref. J H L N A/C A/F K M Throat Dia. F D E G O Throat Dia. Straight with Male Fitting M Throat N Dia. A/C* A/F* Catalog Number 1 .19" 1 .28" .59" 1 .20" 1 .06" .60" 1 .16" 1 .02" 074093441 1/2 1 .19" 1 .28" .59" 1 .34" 1 .19" .61" 1 .21" 1 .06" 074093442 3/4 1 .19" 1 .43" .59" 1 .55" 1 .45" .84" 1 .50" 1 .32" 074093443 1 1 .38" 1 .53" .66" 1 .95" 1 .69" 1 .05" 1 .82" 1 .59" 074093444 11/4 1 .42" 1 .69" .63" 2 .39" 2 .06" 1 .37" 2 .32" 2 .03" 074093445 11/2 1 .66" 2 .00" .66" 2 .72" 2 .38" 1 .60" 2 .62" 2 .29" 074093446 2 1 .69" 2 .25" .66" 3 .08" 2 .88" 2 .05" 3 .21" 2 .80" 074093448 45 Angle with Male Fitting with Insulated Throat J Ref. K L A/C* A/F* M Throat N Dia. A/C* A/F* Catalog Number 1 .25" 1 .28" .66" 1 .20" 1 .06" .57" 1 .16" 1 .02" 074093561 1/2 1 .25" 1 .28" .66" 1 .34" 1 .19" .57" 1 .21" 1 .06" 074093562 3/4 1 .25" 1 .44" .66" 1 .55" 1 .45" .78" 1 .50" 1 .32" 074093563 1 1 .44" 1 .53" .72" 1 .95" 1 .69" .98" 1 .82" 1 .59" 074093564 11/4 1 .48" 1 .69" .69" 2 .39" 2 .06" 1 .29" 2 .32" 2 .03" 074093565 11/2 1 .72" 2 .00" .72" 2 .72" 2 .38" 1 .53" 2 .62" 2 .29" 074093566 2 1 .75" 2 .25" .72" 3 .08" 2 .87" 1 .95" 3 .21" 2 .80" 074093568 90 Angle with Male Fitting Dimensions C A/C* A/F* L A/C* A/F* Trade H Size B K Dimensions P A/C A/F Trade A Size Ref. J Ref. D Throat E Dia. A/C* A/F* Catalog Number Dimensions 1 .43" .59" 1 .20" 1 .06" .61" 1 .07" .93" 074093401 1/2 1 .43" .59" 1 .34" 1 .19" .61" 1 .22" 1 .06" 074093402 1 .31" .59" 1 .20" 1 .06" 1 .44" .60" 1 .13" .99" 3/4 1 .56" .59" 1 .55" 1 .37" .84" 1 .43" 1 .25" 074093403 1/2 1 .31" .59" 1 .34" 1 .12" 1 .44" .61" 1 .21" 1 .00" 074093422 1 1 .68" .66" 1 .95" 1 .69" 1 .06" 1 .73" 1 .56" 074093404 3/4 1 .44" .59" 1 .55" 1 .45" 1 .63" .83" 1 .48" 1 .29" 074093423 11/4 2 .03" .63" 2 .39" 2 .06" 1 .37" 2 .36" 2 .08" 074093405 1 1 .78" .66" 1 .95" 1 .60" 2 .19" 1 .05" 1 .80" 1 .57" 074093424 11/2 2 .21" .63" 2 .72" 2 .38" 1 .53" 2 .79" 2 .48" 074093406 11/4 1 .97" .63" 2 .39" 2 .06" 2 .50" 1 .37" 2 .32" 2 .02" 074093425 2 2 .28" .69" 3 .08" 2 .87" 2 .06" 3 .32" 2 .90" 074093408 11/2 2 .19" .66" 2 .72" 2 .38" 2 .69" 1 .61" 2 .58" 2 .25" 074093426 2 2 .53" .66" 3 .08" 2 .87" 3 .25" 2 .05" 3 .14" 2 .75" 074093428 Straight with Male Fitting with Insulated Throat Dimensions B C A/C* A/F* D Throat E Dia. A/C* A/F* Catalog Number E F A/C* A/F* G Ref. O Throat P Dia. A/C* A/F* Trade D Size Trade A Size Ref. Catalog Number 074093421 90 Angle with Male Fitting with Insulated Throat Dimensions E F A/C* A/F* G Ref. O Throat P Dia. A/C* A/F* 1 .50" .66" 1 .20" 1 .06" .57" 1 .07" .93" 074093511 Catalog Number 1/2 1 .50" .66" 1 .34" 1 .19" .57" 1 .22" 1 .06" 074093512 1 .38" .66" 1 .20" 1 .06" 1 .44" .60" 1 .13" .99" 3/4 1 .62" .66" 1 .55" 1 .38" .78" 1 .43" 1 .25" 074093513 1/2 1 .38" .66" 1 .34" 1 .12" 1 .44" .57" 1 .21" 1 .00" 074093542 1 1 .75" .72" 1 .95" 1 .69" .98" 1 .73" 1 .56" 074093514 3/4 1 .50" .66" 1 .55" 1 .45" 1 .63" .78" 1 .48" 1 .29" 074093543 11/4 2 .09" .69" 2 .39" 2 .06" 1 .29" 2 .36" 2 .08" 074093515 1 1 .84" .66" 1 .95" 1 .60" 2 .19" .98" 1 .80" 1 .57" 074093544 2 .03" .69" 2 .39" 2 .06" 2 .50" 1 .29" 2 .32" 2 .02" 074093545 074093541 11/2 2 .28" .69" 2 .72" 2 .37" 1 .53" 2 .79" 2 .48" 074093516 11/4 2 2 .34" .75" 3 .08" 2 .87" 1 .95" 3 .32" 2 .90" 074093518 11/2 2 .25" .69" 2 .72" 2 .38" 2 .69" 1 .53" 2 .58" 2 .20" 074093546 074093520 2 2 .59" .72" 3 .08" 2 .87" 3 .25" 1 .95" 3 .14" 2 .75" 074093548 3 .44" 1 .00" 3 .92" 3 .63" 4 .25" 2 .42" 3 .78" 3 .50" 074093550 3 .75" 1 .00" 4 .70" 4 .31" 4 .87" 3 .01" 4 .64" 4 .30" 074093552 3 .56" 1 .06" 3 .92" 3 .62" 2 .42" 3 .85" 3 .60" 3 3 .81" 1 .06" 4 .70" 4 .31" 3 .01" 4 .65" 4 .33" 074093522 21/2 4 3 .81" 1 .06" 5 .75" 5 .31" 3 .96" 5 .75" 5 .39" 074093526 3 Note: *A/C - Across Corners; A/F - Across Flats. Dimensions shown are approximate and are subject to change without notice. Dimensions in Inches (cm) www.hubbell-wiring.com T-79 Technical Information Trade D Size 21/2 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Strain Relief for Liquidtight Conduit Dimensional Charts For UL Type A, Liquidtight Conduit Grip Fittings Straight with Male Fitting with Insulated Throat Dimensions Inches (cm) Trade Size N.P.T. Inches A B C D Catalog Number 1/2 3/4 1 1 .922" (4 .88) 1 .922" (4 .88) 2 .016" (5 .12) 2 .157" (5 .48) .594" (1 .51) .594" (1 .51) .594" (1 .51) .719" (1 .83) 1 .156" (2 .94) 1 .250" (3 .17) 1 .500" (3 .81) 1 .844" (4 .68) 3 .75" (9 .52) 4 .50" (11 .43) 6 .25" (15 .87) 7 .50" (19 .05) H038CNK H050CNK H075CNK H100CNK 11/4 11/2 2 2 .219" (5 .64) 2 .344" (5 .95) 2 .406" (6 .11) .750" (1 .91) .750" (1 .91) .750" (1 .91) 2 .312" (5 .87) 2 .578" (6 .55) 3 .187" (8 .09) 9 .00" (22 .86) 13 .50" (34 .29) 14 .50" (36 .83) H125CNK H150CNK H200CNK C Flats B Ref. D A Ref. 90 Angle with Male Fitting with Insulated Throat Dimensions Inches (cm) Trade Size N.P.T. Inches E F G H I Catalog Number 1/2 3/4 1 1 .250" (3 .18) 1 .281" (3 .25) 1 .438" (3 .65) 1 .750" (4 .44) .594" (1 .51) .594" (1 .51) .594" (1 .51) .719" (1 .83) 1 .156" (2 .94) 1 .250" (3 .17) 1 .500" (3 .81) 1 .844" (4 .68) 1 .453" (3 .69) 1 .453" (3 .69) 1 .000" (2 .54) 2 .125" (5 .40) 3 .75" (9 .52) 4 .50" (11 .43) 6 .25" (15 .87) 7 .50" (19 .05) H0389CNK H0509CNK H0759CNK H1009CNK 11/4 11/2 2 1 .969" (5 .00) 2 .250" (5 .71) 2 .531" (6 .43) .750" (1 .91) .750" (1 .91) .750" (1 .91) 2 .312" (5 .87) 2 .578" (6 .55) 3 .187" (8 .09) 2 .344" (5 .95) 2 .500" (6 .35) 2 .781" (7 .06) 9 .00" (22 .86) 13 .50" (34 .29) 14 .50" (36 .83) H1259CNK H1509CNK H2009CNK Technical Information G Flats E I F H Dimensions shown are approximate and are subject to change without notice. T-80 www.hubbell-wiring.com Dimensions in Inches (cm) Cord Connectors Features and Benefits Machined threads provide a strong positive seal; the tapered interior dome easily drives the bushing into the connector body The patented GOTHCA(R) ring incorporates a split hinge design to prevent friction and provide strain relief, also color-coded for sizing identification Kellems(R) Wire Management Products Kellems(R) Wire Management Products Lubricated neoprene bushing compresses easily for a liquidtight seal and added pull-out protection The connector body is a one-piece design with machined threads; a tapered interior seats the bushing evenly for a liquidtight seal Hubbell has the broadest line and the widest choice of materials in the industry . N .P .T . hub sizes from 1/4" to 3" in straight male end, 90, 45, female and underground feed connectors . They are available in your choice of aluminum, plated steel, nylon and stainless steel . The zinc-plated steel cord connectors offers the strength of steel and the corrosion resistance of zinc-plating . These heavy-duty connectors hold up to most manufacturing chemicals including acid solutions, solvents and other corrosive materials . Dimensions in Inches (cm) Hubbell's nylon cord connectors resist most common industrial corrosives and provide highly effective pullout protection in a lightweight design . They are ideal for any application where weight, conductivity or corrosion may be an issue . They're available in N .P .T . hub sizes from 1/4" to 1" . Stainless steel cord connectors provide superior strength and corrosion resistance for industrial and military applications . They are machined from 300 series stainless steel and come in 1/4" to 1", N .P .T . hub sizes . www.hubbell-wiring.com T-81 Cord Connectors Hubbell offers a full line of machined aluminum cord connectors in N .P .T . hub sizes 1/4" through 1" and cast aluminum 1" to 3" . They provide durable performance and a clean attractive look without adding unwanted weight . N .P .T . hub sizes 1/4" to 1" feature an attractive knurled finish which makes them easy to handle and maintain a U .L . listing by hand tightening . Their machined steel nut and body allows for tightening the compression nut and N .P .T . hub without worrying about stripping the threads . For larger size cord, N .P .T . hub sizes 1" to 2", Hubbell utilizes malleable iron connectors which provide excellent holding and liquidtight performance . Kellems(R) Wire Management Products Kellems(R) Wire Management Products Straight Male Cord Connectors UL Listed to Type 4, 4X, 12 and Type 13 Form Size 1-3 IP66* SUITABILITY Straight Male N.P.T. Cord Dia. Hub Inches Form Size (mm) Size 1/4 Machined Aluminum Machined Zinc-Plated Steel 1/2 Straight Male Cord Connectors 1/2 1/2 .06"- .13" (1 .6-3 .2) .13"- .19" (3 .2-4 .7) .19"- .25" (4 .7-6 .3) .25"- .31" (6 .3-7 .9) .31"- .38" (7 .9-9 .5) .38"- .44" (9 .5-11) .06"- .13" (1 .6-3 .2) .13"- .19" (3 .2-4 .7) .19"- .25" (4 .7-6 .3) .25"- .31" (6 .3-7 .9) .31"- .38" (7 .9-9 .5) .38"- .44" (9 .5-11 .0) .19"- .25" (4 .7-6 .3) .25"- .31" (6 .3-7 .9) .31"- .38" (7 .9-9 .5) .38"- .44" (9 .5-11 .0) .06"- .13" (1 .6-3 .2) .13"- .19" (3 .2- .4 .7) .19"- .25" (4 .7-6 .3) .25"- .38" (6 .3- .9 .7) .38"- .50" (9 .7-12 .7) .50"- .63" (12 .7-15 .9) .38"- .50" (9 .7-12 .7) .50"- .63" (12 .7-15 .9) .63"- .75" (15 .9-19 .0) .75"- .88" (19 .0-22 .2) F1 Color Code Machined Aluminum Machined Zinc-Plated Steel Green -- -- -- SHC1001CR -- Orange SHC1002 -- -- SHC1002CR -- Red SHC1003 -- SHC1003SS SHC1003CR -- Black SHC1004 -- SHC1004SS SHC1004CR -- White SHC1005** -- -- SHC1005CR Blue -- -- -- SHC1006CR SHC1007 -- -- Green Orange SHC1008 F1 F1 F2 -- -- Nylon Black -- SHC2005CR -- -- SHC1008CR Black SHC1010 White SHC1011 Blue SHC1012 Red SHC1015 -- -- -- -- Black SHC1016 -- -- -- -- White SHC1017 -- -- -- -- Blue SHC1018 -- -- -- -- Green SHC1019 -- -- -- SHC1012ZP -- SHC1009CR SHC2008CR SHC1009 SHC1010ZP SHC1009SS Nylon Gray Red -- SHC1010CR SHC2010CR SHC1011SS SHC1011CR SHC2011CR SHC1012SS SHC1012CR SHC2012CR SHC1019CR -- -- Orange SHC1020 SHC1020ZP SHC1020SS SHC1020CR Red SHC1021 SHC1021ZP SHC1021SS SHC1021CR SHC2021CR White SHC1022 SHC1022ZP SHC1022SS SHC1022CR SHC2022CR Blue SHC1023 SHC1023ZP SHC1023SS SHC1023CR SHC2023CR Brown SHC1024 SHC1024ZP SHC1024SS SHC1024CR** SHC2024CR** SHC1025 -- -- -- -- Brown SHC1026 -- -- -- -- Yellow SHC1027** SHC1027ZP** -- -- -- Orchid SHC1028** SHC1028ZP** -- -- -- Blue F3 SHC1008ZP Stainless Steel Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * IP66 Suitability when used with optional metal clad O-ring shown on page T-89. ** Cable jacket may have to be stripped to pass through connector body. Locknuts sold separately. See page T-89. T-82 www.hubbell-wiring.com Dimensions in Inches (cm) Straight Male Cord Connectors UL Listed to Type 4, 4X, 12 and Type 13 Form Size 2-4 IP66* SUITABILITY Straight Male N.P.T. Cord Dia. Hub Inches Form Color Size (mm) Size Code 3/4 3/4 1 1 .06"- .13" (1 .6-3 .2) .13"- .19" (3 .2-4 .7) .19"- .25" F2 (4 .7-6 .3) .25"- .38" (6 .3-9 .7) .38"- .50" (9 .7-12 .7) .50"- .63" (12 .7-15 .9) .38"- .50" (9 .5-12 .7) 50"- .63" F3 (12 .7-15 .9) .63"- .75" (15 .9-19 .0) .75"- .88" (19 .0-22 .2) .50"- .63" F3 (12 .7-15 .9) .63"- .75" (15 .9-19 .0) .75"- .88" (19 .0-22 .2) .38"- .50" (9 .7-12 .7) .50"- .63" (12 .7-15 .9) .63"- .75" F4 (15 .9-19 .0) .75"- .88" (19 .0-22 .2) .88"-1 .00" (22 .2-25 .4) 1 .00"-1 .13" (25 .4-28 .6) Machined Aluminum Green SHC1029 Machined Zinc-Plated Steel Stainless Steel -- Nylon Gray -- -- -- Orange SHC1030 SHC1030ZP -- -- -- Red SHC1031 SHC1031ZP -- -- -- White SHC1032 SHC1032ZP -- -- -- Blue SHC1033 SHC1033ZP -- -- -- Brown SHC1034 SHC1034ZP -- -- -- Blue -- Brown SHC1036 Yellow SHC1037 SHC1035ZP -- SHC1037ZP SHC1035SS SHC1035CR SHC2035CR SHC1036SS SHC1036CR SHC2036CR SHC1037SS SHC1037CR SHC2037CR Stainless Steel Orchid SHC1038** SHC1038ZP** SHC1038SS** SHC1038CR** SHC2038CR** Brown -- SHC1097ZP -- -- -- Yellow -- SHC1098ZP -- -- -- Orchid -- SHC1099ZP -- -- -- SHC1039 -- -- SHC1039CR Brown SHC1040 -- -- SHC1040CR SHC2040CR Yellow SHC1041 -- SHC1041SS SHC1041CR SHC2041CR Orchid SHC1042 -- SHC1042SS SHC1042CR SHC2042CR SHC1043CR SHC2043CR Blue Gray SHC1043 Pink SHC1044** SHC1043ZP -- -- Gray Nylon -- SHC1044SS** SHC1044CR** SHC2044CR** www.hubbell-wiring.com Black Nylon T-83 Straight Male Cord Connectors Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * IP66 Suitability when used with optional metal clad O-ring shown on page T-89. ** Cable jacket may have to be stripped to pass through connector body. Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum. Locknuts sold separately. See page T-89. Dimensions in Inches (cm) Nylon Black Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Straight Male Cord Connectors UL Listed to Type 4, 4X, 12 and Type 13 Form Size 5-8 IP66* SUITABILITY Straight Male N.P.T. Hub Size 1 11/4 Cast Aluminum 11/2 11/2 2 Cast Aluminum Malleable Iron 2 21/2 Straight Male Cord Connectors 3 3 Cord Diameter Inches (mm) .88"-1 .00" 1 .00"-1 .13" 1 .13"-1 .25" 1 .25"-1 .38" .75"- .88" .88"-1 .00" 1 .00"-1 .13" 1 .13"-1 .25" 1 .25"-1 .38" .75"- .88" .88"-1 .00" 1 .00"-1 .13" 1 .13"-1 .25" 1 .25"-1 .38" 1 .38"-1 .50" 1 .50"-1 .63" 1 .63"-1 .75" 1 .75"-1 .88" 1 .25"-1 .38" 1 .38"-1 .50" 1 .50"-1 .63" 1 .63"-1 .75" 1 .75"-1 .88" 1 .69"-1 .81" 1 .81"-1 .94" 1 .94"-2 .06" 2 .06"-2 .19" 2 .19"-2 .31" 1 .69"-1 .81" 1 .81"-1 .94" 1 .94"-2 .06" 2 .06"-2 .19" 2 .19"-2 .31" 2 .31"-2 .44" 1 .69"-1 .81" 1 .94"-2 .06" 2 .06"-2 .19" 2 .19"-2 .31" 2 .31"-2 .44" 2 .44"-2 .63" 2 .63"-2 .81" 2 .81"-3 .00" 3 .00"-3 .25" (22 .2-25 .4) (25 .4-28 .6) (28 .6-31 .7) (31 .7-34 .9) (19 .0-22 .2) (22 .2-25 .4) (25 .4-28 .6) (28 .6-31 .7) (31 .7-34 .9) (19 .0-22 .2) (22 .2-25 .4) (25 .4-28 .6) (28 .6-31 .7) (31 .7-34 .9) (34 .9-38 .1) (38 .1-41 .3) (41 .3-44 .4) (44 .4-47 .6) (31 .7-34 .9) (34 .9-38 .1) (38 .1-41 .3) (41 .3-44 .4) (44 .4-47 .6) (42 .9-46 .0) (46 .0-49 .2) (49 .2-52 .4) (52 .4-55 .6) (55 .6-58 .7) (42 .9-46 .0) (46 .0-49 .2) (49 .2-52 .4) (52 .4-55 .6) (55 .6-58 .7) (58 .7-61 .9) (42 .9-46 .0) (49 .2-52 .4) (52 .4-55 .6) (55 .6-58 .7) (58 .7-61 .9) (61 .9-66 .7) (66 .7-71 .4) (71 .4-76 .2) (76 .2-82 .5) Form Size F5 F5 F5 F6 F6 F7 F7 F7 F8 Cast Aluminum Malleable Iron SHC1046 SHC1047** SHC1048** SHC1049** SHC1050 SHC1051 SHC1052 SHC1053 SHC1054** SHC1055 SHC1056 SHC1057 SHC1058 SHC1059 SHC1061 SHC1062** SHC1063** SHC1064** SHC1065 SHC1066 SHC1067 SHC1068 SHC1069 SHC1070 SHC1071 SHC1072** SHC1073** SHC1074** SHC1076 SHC1077 SHC1078 SHC1079 SHC1080 SHC1081** SHC1086 SHC1088 SHC1089 SHC1090 SHC1091 SHC1092 SHC1093 SHC1094 SHC1095** -- -- -- -- -- -- SHC1052ZP SHC1053ZP SHC1054ZP -- -- SHC1057ZP SHC1058ZP SHC1059ZP -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * IP66 Suitability when used with optional metal clad O-ring shown on page T-89. ** Cable jacket may have to be stripped to pass through connector body. Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum. F5 and larger will not be color coded. Locknuts sold separately. See page T-89. T-84 www.hubbell-wiring.com Dimensions in Inches (cm) 45 Male Cord Connectors UL Listed to Type 4, 4X, 12 and Type 13 Form Size 2-5 IP66* SUITABILITY 45 Male N.P.T. Hub Size 1/2 3/4 1 11/4 Cord Diameter Inches (mm) .19"- .25" .25"- .38" .38"- .50" .50"- .63" .38"- .50" .50"- .63" .63"- .75" .63"- .75" .75"- .88" 1 .00"-1 .13" 1 .13"-1 .25" (4 .7-6 .3) (6 .3-9 .7) (9 .7-12 .7) (12 .7-15 .9) (9 .7-12 .7) (12 .7-15 .9) (15 .9-19 .0) (15 .9-19 .0) (19 .0-22 .2) (25 .4-28 .6) (28 .6-31 .7) Form Size F2 F3 F4 F5 Color Code Red White Blue Brown Blue Brown Yellow Yellow Orchid Machined Machined Aluminum Zinc-Plated Steel Cast Aluminum VHC1021 VHC1022 VHC1023 VHC1024** VHC1035 VHC1036 VHC1037** VHC1041 VHC1042 -- -- -- VHC1022ZP VHC1023ZP VHC1024ZP** -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- VHC1052 VHC1053** Machined Aluminum Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * IP66 Suitability when used with optional metal clad O-ring shown on page T-89. ** Cable jacket may have to be stripped to pass through connector body. Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum. Nuts are machined aluminum and bodies are cast aluminum. Nuts are machined zinc-plated steel and bodies are malleable iron, cadmium plated. Locknuts sold separately. See page T-89. Machined Zinc-Plated Steel Cast Aluminum 45 Male Cord Connectors Dimensions in Inches (cm) www.hubbell-wiring.com T-85 Kellems(R) Wire Management Products Kellems(R) Wire Management Products 90 Male Cord Connectors UL Listed to Type 4, 4X, 12 and Type 13 Form Size 1-6 IP66* SUITABILITY 90 Male N.P.T. Hub Size 1/2 3/4 1 11/4 11/2 2 Cord Diameter Inches (mm) .25"- .31" .31"- .38" .38"- .44" .06"- .13" .13"- .19" .19"- .25" .25"- .38" .38"- .50" .50"- .63" .38"- .50" .50"- .63" .63"- .75" .75"- .88" .50"- .63" .63"- .75" .75"- .88" .88"-1 .00" 1 .00"-1 .13" .88"-1 .00" 1 .00"-1 .13" 1 .13"-1 .25" 1 .25"-1 .38" 1 .00"-1 .13" 1 .13"-1 .25" 1 .25"-1 .38" 1 .38"-1 .50" (6 .3-7 .9) (7 .9-9 .5) (9 .5-11 .0) (1 .6-3 .2) (3 .2-4 .7) (4 .7-6 .3) (6 .3-9 .7) (9 .7-12 .7) (12 .7-15 .9) (9 .7-12 .7) (12 .7-15 .9) (15 .9-19 .0) (19 .0-22 .2) (12 .7-15 .9) (15 .9-19 .0) (19 .0-22 .2) (22 .2-25 .4) (25 .4-28 .7) (22 .2-25 .4) (25 .4-28 .6) (28 .6-31 .7) (31 .7-34 .9) (25 .4-28 .6) (28 .6-31 .7) (31 .7-34 .9) (34 .9-38 .1) Form Size F1 F2 F3 F4 F5 F5 F6 Color Code Machined Aluminum Machined Zinc-Plated Steel Nylon Gray Nylon Black Cast Aluminum Black White Blue Green Orange Red White Blue Brown Blue Brown Yellow Orchid Brown Yellow Orchid Gray Pink -- -- -- -- -- -- -- -- NHC1010 NHC1011 NHC1012 -- NHC1020 NHC1021 NHC1022 NHC1023 NHC1024** NHC1035 NHC1036 NHC1037 NHC1038 NHC1040 NHC1041 NHC1042 NHC1043** NHC1044** -- -- -- -- -- -- -- -- -- -- -- -- -- NHC1021ZP NHC1022ZP NHC1023ZP NHC1024ZP** NHC1035ZP NHC1036ZP NHC1037ZP NHC1038ZP -- NHC1041ZP -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- NHC1020CR NHC1021CR NHC1022CR NHC1023CR NHC1024CR** NHC1035CR NHC1036CR NHC1037CR NHC1038CR -- NHC1041CR NHC1042CR NHC1043CR -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- NHC2022CR NHC2023CR NHC2024CR** -- -- -- -- -- NHC2041CR NHC2042CR** NHC2043CR** -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- NHC1051 NHC1052 NHC1053** NHC1054** NHC1057 -- NHC1059 NHC1066 90 Male Cord Connectors Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * IP66 Suitability when used with optional metal clad O-ring shown on page T-89. ** Cable jacket may have to be stripped to pass through connector body. Nuts are machined aluminum and bodies are cast aluminum. Compression nuts are machined zinc-plated steel and bodies are zinc-plated malleable iron. Locknuts sold separately. See page T-89. Machined Aluminum Gray Nylon T-86 Machined Zinc-Plated Steel Black Nylon www.hubbell-wiring.com Cast Aluminum Dimensions in Inches (cm) Straight Female, Underground Feeder and Metric Connectors Form Size 1-4 Straight Female N.P.T. Hub Size 1/2 3/4 1 Cord Diameter Inches (mm) Form Size Color Code Machined Aluminum .25"- .38" .38"- .50" .38"- .50" .50"- .63" .75"- .88" .88"-1 .00" F2 White Blue Blue Brown Orchid Gray FHC1022 FHC1023 FHC1033 FHC1034 FHC1042 FHC1043 (6 .3-9 .7) (9 .7-12 .7) (9 .7-12 .7) (12 .7-15 .9) (19 .0-22 .2) (22 .2-25 .4) F2 F4 Machined Aluminum Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * Cable jacket may have to be stripped to pass through connector body. Nuts are machined aluminum and bodies are cast aluminum. Kellems(R) Wire Management Products Kellems(R) Wire Management Products IP66* SUITABILITY Underground Feeder Connectors (mm) 1/2 .2"x .4" min .25"- .55" max (5 .1 x 10 .2) (6 .3 x 14 .0) 3/4 .2"x .4" min .25"- .55" max (5 .1x10 .2) (6 .3x14 .0) 3/4 .2"x .6" min .26"x .78" max (5 .1x15 .2) (6 .6x19 .8) Wire Size 2 # 14, 2 # 12, 2 # 10 . 2 # 14, 2 # 12, 2 # 10 . 3 # 14, 3 # 12, 3 # 10 . UF** Machined Aluminum Zinc-Plated Steel Machined Nylon Gray Nylon Black UFC0001 UFC0001ZP UFC0001CR UFC2001CR UFC0002 -- UFC0003 -- -- UFC0003CR Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. * IP66 Suitability when used with optional metal clad O-ring shown on page T-89. ** Wire sizes vary among manufacturers. Locknuts sold separately. See page T-89. Machined Aluminum -- UFC2003CR Machined Zinc-Plated Steel UL Listed to Type 4, 4X, 12 and Type 13 Metric Aluminum Cord Connectors Hub Size Cord Diameter Inches (mm) Form Size M16 M20 .31"- .38" .31"- .38" .25"- .38" .38"- .50" .50"- .62" .38"- .50" .50"- .62" .63"-75" F1 F1 M20 M25 M30 (7 .9-9 .7) (7 .9-9 .7) (6 .3-9 .7) (9 .7-12 .7) (12 .7-15 .8) (9 .7-12 .7) (12 .7-15 .8) (15 .9-19 .0) Catalog Number SHCM161011 SHCM201017 SHCM201022 SHCM201023 SHCM201024 SHCM251033 SHCM251034 SHCM301037 F2 F2 F3 Gray Nylon Note: When used with metal clad O-ring shown on page T-89. Non-metallic Locknuts sold separately. See page T-88. Machined Aluminum Dimensions in Inches (cm) www.hubbell-wiring.com T-87 Straight Female, Underground Feeder and Metric Connectors N.P.T. Hub Diameter Size Inches Kellems(R) Wire Management Products Kellems(R) Wire Management Products Low Profile N.P.T., PG and Metric Thread Connectors Non-Metallic Cord Connectors IP66* SUITABILITY Low Profile N.P.T. Cord Connectors SEC100BA N.P.T. Hub Size Inches Cord Diameter (mm) Color Catalog Number Non-metallic Locknuts 1/2 1/2 3/4 3/4 1 1 .18"- .31" .18"- .31" .17"- .45" .17"- .45" .45"- .71" .45"- .71" .59"-1 .00" .59"-1 .00" (4 .6-7 .9) (4 .6-7 .9) (4 .3-11 .4) (4 .3-11 .4) (11 .4-18 .0) (11 .4-18 .0) (15-25 .4) (15-25 .4) Gray Black Gray Black Gray Black Gray Black SEC38GA* SEC38BA* SEC50GA SEC50BA SEC75GA SEC75BA SEC100GA SEC100BA 31622002LPK50 31622002LPK50 31622003LPK50 31622003LPK50 31622007LPK50 31622007LPK50 31622008LPK50 31622008LPK50 Note: See pages T-92 to T-101 for additional technical data and dimensional drawings. Catalog numbers with "PK50" suffix are bulk packed 50 pieces. Low Profile PG Cord Connectors Low Profile N .P .T ., PG and Metric Thread Connectors SECP29GA Hub Size Cord Diameter Inches (mm) Color Catalog Number Non-metallic Locknuts PG7 PG7 PG9 PG9 PG11 PG11 PG13 .5 PG13 .5 PG16 PG16 PG21 PG21 PG29 PG29 PG36 PG36 .11"- .25" .11"- .25" .18"- .31" .18"- .31" .23"- .40" .23"- .40" .17"- .47" .17"- .47" .23"- .53" .23"- .53" .45"- .71" .45"- .71" .59"- .99" .59"- .99" .88"-1 .30" .88"-1 .30" Gray Black Gray Black Gray Black Gray Black Gray Black Gray Black Gray Black Gray Black SECP7GA* SECP7BA* SECP9GA* SECP9BA* SECP11GA* SECP11BA* SECP13GA SECP13BA SECP16GA SECP16BA SECP21GA SECP21BA SECP29GA SECP29BA SECP36GA SECP36BA LNP7BPK100 LNP7BPK100 LNP9BPK100 LNP9BPK100 LNP11BPK100 LNP11BPK100 LNP13BPK100 LNP13BPK100 LNP16BPK100 LNP16BPK100 LNP21BPK100 LNP21BPK100 LNP29BPK25 LNP29BPK25 LNP36BPK25 LNP36BPK25 (2 .9-6 .4) (2 .9-6 .4) (4 .6-7 .9) (4 .6-7 .9) (5 .8-10 .0) (5 .8-10 .0) (4 .3-11 .9) (4 .3-11 .9) (5 .8-13 .5) (5 .8-13 .5) (11 .4-17 .9) (11 .4-17 .9) (15-25 .2) (15-25 .2) (22 .2-32 .0) (22 .2-32 .0) Low Profile Metric Cord Connectors LNP29BPK25 Hub Size Cord Diameter Inches (mm) Color Catalog Number Non-metallic Locknuts M12 M12 M16 M16 M20 M20 M25 M25 M32 M32 M40 M40 .12"- .25" .12"- .25" .11"- .31" .11"- .31" .17"- .45" .17"- .45" .49"- .71" .49"- .71" .59"-1 .00" .59"-1 .00" .87"-1 .30" .87"-1 .30" Gray Black Gray Black Gray Black Gray Black Gray Black Gray Black SECM12G SECM12B SECM16G SECM16B SECM20G* SECM20B* SECM25G* SECM25B* SECM32G* SECM32B* SECM40G SECM40B LNM12BPK100 LNM12BPK100 LNM16BPK100 LNM16BPK100 LNM20BPK100 LNM20BPK100 LNM25BPK100 LNM25BPK100 LNM32BPK100 LNM32BPK100 LNM40BPK100 LNM40BPK100 (2 .9-6 .4) (2 .9-6 .4) (2 .7-7 .9) (2 .7-7 .9) (4 .3-11 .4) (4 .3-11 .4) (12 .3-18 .0) (12 .3-18 .0) (15 .0-25 .4) (15 .0-25 .4) (22 .0-32 .0) (22 .0-32 .0) Note: See pages T-92 to T-101 for additional technical data and dimensional data. Catalog numbers above with "PK100" suffix, i.e. LNP7BPK100, are bulk packed 100 per carton. Catalog numbers above with "PK25" suffix, i.e. LNP29BPK25, are bulk packed 25 per carton. * Items indicated are UL recognized components. Panzergewinde. T-88 www.hubbell-wiring.com Dimensions in Inches (cm) Accessories Cord Connector Parts N.P.T. Hub Size Cord Diameter Inches (mm) 1/4, , 1/2 .062"- .125" .125"- .187" .187"- .250" .250"- .312" .312"- .375" .375"- .437" .187"- .250" .250"- .375" .375"- .500" .500"- .625" .375"- .500" .500"- .625" .625"- .750" .750"- .875" .500"- .625" .625"- .750" .750"- .875" .875"-1 .00" 1 .00"-1 .125" 1/2, 3/4 1/2, 3/4 1 (1 .58-3 .17) (3 .17-4 .76) (4 .76-6 .35) (6 .35-7 .93) (7 .93-9 .50) (9 .50-11 .1) (4 .76-6 .35) (6 .35-9 .50) (9 .50-12 .7) (12 .7-15 .8) (9 .50-12 .7) (12 .7-15 .8) (15 .8-19 .0) (19 .0-22 .2) (12 .7-15 .8) (15 .8-19 .0) (19 .0-22 .2) (22 .2-25 .4) (25 .4-28 .5) Form Size F1 F2 F3 F4 Bushing Catalog Number Color Code GOTCHA(R) Ring Catalog Number 31518101BPK100 31518102BPK100 31518103BPK100 31518104BPK100 31518105BPK100 31518106BPK100 31518110BPK100 31518111BPK100 31518112BPK100 31518113BPK100 31518116BPK100 31518117BPK100 31518118BPK100 31518119BPK100 31518123BPK100 31518124BPK100 31518125BPK100 31518126BPK100 31518127BPK100 Green Orange Red Black White Blue Red White Blue Brown Blue Brown Yellow Orchid Brown Yellow Orchid Gray Pink 31648035GPK100 31648036GPK100 31648037GPK100 31648038GPK100 31605010GPK100 31648039GPK100 31648042GPK100 31605015GPK100 31648043GPK100 31648044GPK100 31648045GPK100 31648046GPK100 31648047GPK100 31648048GPK100 31648050GPK100 31648051GPK100 31648052GPK100 31648053GPK100 31648054GPK100 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: Catalog numbers above with "PK100" suffix, i.e. 31518101BPK100, are bulk packed 100 per carton. Locknuts -- Steel and Non-Metallic N.P.T. Hub Size Zinc-Plated Steel Non-Metallic 1/4 1/2 3/4 1 11/4 11/2 -- -- 00322001LPK50 00322002LPK50 00322003LPK50 00322004LPK50 00322005LPK50 31622001LPK50 31622002LPK50 31622003LPK50 31622007LPK50 31622008LPK50 -- -- Zinc-Plated Steel Locknuts Note: Catalog numbers above with "PK50" suffix, i.e. 00322001LPK50, are bulk packed 50 per carton. See page T-101 for additional technical data and dimensional drawings. Metal Clad Sealing O-Rings Catalog Number 1/2 3/4 1 11/4 11/2 2 21/2 3 20509001 20509002 20509003 20509004 20509005 20509006 20509007 20509008 Note: See page T-101 for additional technical data and dimensional drawings. Dimensions in Inches (cm) www.hubbell-wiring.com Non-Metallic Locknuts Metal Clad Sealing O-Rings T-89 Accessories N.P.T. Hub Size Kellems(R) Wire Management Products Kellems(R) Wire Management Products Hubbell Juniors(R) Miniature Connectors Hubbell Juniors are a miniature liquidtight version of the full-sized Hubbell cord connectors . They feature the same GOTCHA(R) ring technology and neoprene bushings . They also come with or without a nylon spiral for arc-of-bend control and longer cord life . They are available in 1/4", ", and 1/2" N .P .T . sizes in both gray and black . Hubbell Juniors(R) Miniature Connectors Nylon spiral provides arc-of-bend control for cord protection Nylon compression nut has a tapered interior dome to easily drive the bushing into the connector body Patented GOTCHA(R) ring incorporates a split hinge design to prevent friction and provide strain relief Lubricated neoprene bushing compresses evenly for a liquidtight seal and added pull-out protection Nylon connector body is a one piece design with a tapered interior that seals the bushing evenly for a positive seal Threaded hexagon shaped nylon locknut secures tightly and is also corrosion resistant T-90 www.hubbell-wiring.com Hubbell Juniors(R) Miniature Nylon Cord Connectors Miniature Nylon Cord Connector N.P.T. Hub Size 1/4 1/2 Cord Diameter Range Inches (mm) Gray Black .08"- .14" .14"- .20" .20"- .27" .15"- .21" .21"- .28" .28"- .34" .06"- .13" .13"- .19" .19"- .25" .25"- .31" .31"- .38" .38"- .44" HJ1001GPK25 HJ1002GPK25 HJ1003GPK25 HJ1004GPK25 HJ1005GPK25 HJ1006GPK25 HJ1055GPK25 HJ1056GPK25 HJ1057GPK25 HJ1058GPK25 HJ1059GPK25 HJ1060GPK25 HJ1001BPK25 HJ1002BPK25 HJ1003BPK25 HJ1004BPK25 HJ1005BPK25 HJ1006BPK25 HJ1055BPK25 HJ1056BPK25 HJ1057BPK25 HJ1058BPK25 HJ1059BPK25 HJ1060BPK25 (1 .9-3 .4) (3 .4-5 .1) (5 .1-6 .7) (3 .7-5 .3) (5 .3-7 .0) (7 .0-8 .6) (1 .6-3 .2) (3 .2-4 .7) (4 .7-6 .3) (6 .3-7 .9) (7 .9-9 .5) (9 .5-11 .1) Gray Cord Connector Kellems(R) Wire Management Products Kellems(R) Wire Management Products Black Cord Connector Miniature Nylon Cord Connector with Spiral N.P.T. Hub Size 1/4 1/2 3/4 Gray Black .08"- .14" .14"- .20" .20"- .27" .15"- .21" .21"- .28" .28"- .34" .13"- .19" .19"- .25" .25"- .31" .31"- .38" .38"- .44" .25"- .49" .45"- .71" HJ1010GPK25 HJ1011GPK25 HJ1012GPK25 HJ1013GPK25 HJ1014GPK25 HJ1015GPK25 HJ1038GPK25 HJ1039GPK25 HJ1040GPK25 HJ1041GPK25 HJ1042GPK25 HJ1043GPK25* HJ1044GPK25* HJ1010BPK25 HJ1011BPK25 HJ1012BPK25 HJ1013BPK25 HJ1014BPK25 HJ1015BPK25 HJ1038BPK25 HJ1039BPK25 HJ1040BPK25 HJ1041BPK25 HJ1042BPK25 HJ1043BPK25* HJ1044BPK25* (1 .9-3 .4) (3 .4-5 .1) (5 .1-6 .7) (3 .7-5 .3) (5 .3-7 .0) (7 .0-8 .6) (3 .2-4 .7) (4 .7-6 .3) (6 .3-7 .9) (7 .9-9 .5) (9 .5-11 .1) (6 .4-12 .3) (11 .4-18 .0) Gray Cord Connector with Spiral Black Cord Connector with Spiral Note: * Locknuts sold separately. See page T-89. Miniature Nylon Snap-In Cord Connector with Spiral Gray Snap-In Cord Connector Cord Diameter Range Inches (mm) For Chassis Thickness Gray Black .22"- .27" .28"- .32" .30"- .36" .32"- .43" .10" (2 .5) Max .10" (2 .5) Max .13" (3 .2) Max .13" (3 .2) Max HS1001GPK25 HS1002GPK25 HS1003GPK25 HS1004GPK25 HS1001BPK25 HS1002BPK25 HS1003BPK25 HS1004BPK25 (5 .6-6 .9) (7 .1-8 .1) (7 .6-9 .1) (8 .1-10 .9) Note: Catalog numbers above with "PK25" suffix, i.e. HJ1001GPK25, are bulk packed 25 per carton. See pages T-102 and T-103 for additional technical data and dimensional drawings. Black Snap-In Cord Connector Dimensions in Inches (cm) www.hubbell-wiring.com T-91 Hubbell Juniors(R) Miniature Nylon Cord Connectors Cord Diameter Range Inches (mm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Cord Connectors Operating Temperatures Material Aluminum Nylon (connectors and GOTCHA(R) rings) Plated steel* Stainless steel* Neoprene (bushings) Temperature Range -40F to +300F (-40C to +149C) -40F to +225F (-40C to +107C) -60F to +1000F (-51C to +537C) -60F to +1000F (-51C to +537C) -30F to +240F (-34C to +115C) Note: * Due to the limiting factors of nylon and neoprene, any complete cord connector with a GOTCHA ring, Form 1-5, will continuously perform in the range of -30F to +225F (-34C to +107C). Cord connectors without GOTCHA rings, Form 6-8, will continuously operate in the range -30F to +240F (-34C to +115C) due to the limiting factor of neoprene. Hazardous Locations Hubbell cord connectors are suitable for use in hazardous locations per Class I Div . 2, Class II Div . 1 & 2, Class Ill Div . 1 & 2 in accordance with the NEC . Flammability Hubbell nylon cord connectors have a UL 94-V2 rating . Approvals Agency UL Listed in accordance with Standard 514B . CSA Certified . United States Coast Guard Approved, Title 46-Part 111 . Form Size Definition The term "Form Size" refers to the physical overall size of a cord connector . Form 1 is the smallest size . Form 8 is the largest size . Technical Information Knockout Holes N.P.T. Hub Size Knockout Hole Recommended Min. to Max. Inches (mm) Knockout Hole Recommended PG Hub Size Inches (mm) Knockout Hole Recommended Metric Hub Size Inches (mm) 1/4 1/2 3/4 1 11/4 11/2 2 21/2 3 .54"- .57" .67"- .70" .86"- .91" 1 .04"-1 .09" 1 .36"-1 .41" 1 .72"-1 .77" 1 .97"-2 .02" 2 .45"-2 .50" 2 .95"-3 .00" 3 .58"-3 .63" PG7 PG9 PG11 PG13 .5 PG16 PG21 PG29 PG36 M12 M16 M20 M25 M32 M40 (13 .7-14 .5) (17 .0-17 .8) (21 .8-23 .0) (26 .4-27 .8) (34 .5-35 .7) (43 .7-44 .9) (50 .0-51 .2) (62 .3-63 .5) (75 .0-76 .2) (90 .9-92 .1) 492" 599" .733" .804" .888" 1 .15" 1 .47" 1 .85" (12 .5) (15 .2) (18 .6) (20 .4) (22 .5) (28 .3) (34 .3) (47 .0) .472" .629" .787" .984" 1 .25" 1 .57" (12) (16) (20) (25) (32) (40) N.P.T., PG and Metric Thread Low Profile Connectors Specifications Material Gland Temperature Range Protection Class Flammability Listings/Certifications 6/6 Nylon . Buna N . -22F to 225F (-30C to 107C) . Cord Connectors are Halogen and Silicon free . IP66 Suitability . UL 94V-2 . UL Listing File E-41567, UL Recognition File E-41567 . CSA File LR27378C, VDE Marks Licence #136681 . SECP29G T-92 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Cord Connectors Straight Hubbell Connectors Aluminum Inches (mm) F A N.P.T. Form 1/4-18 1 -18 1 1/2-14 1 1/2-14 2 1/2-14 3 3/4-14 2 3/4-14 3 1-111/2 4 1-111/2 5 11/4-111/2 5 11/2-111/2 5 11/2-111/2 6 2-111/2 6 2-111/2 7 21/2-8 7 21/2-8 8 3-8 7 3-8 8 B Dia. Ref. .88" (22 .4) .88" (22 .4) .88" (22 .4) 1 .13" (28 .7) 1 .38" (35 .1) 1 .13" (28 .7) 1 .38" (35 .1) 1 .75" (44 .4) 2 .31" (58 .7) 2 .31" (58 .7) 2 .31" (58 .7) 3 .00" (76 .2) 3 .00" (76 .2) 3 .85" (97 .8) 3 .85" (97 .8) 4 .75" (120 .6) 3 .85" (97 .8) 4 .50" (114 .3) .90" (22 .9) .90" (22 .9) .90" (22 .9) 1 .10" (27 .9) 1 .50" (38 .1) 1 .10" (27 .9) 1 .50" (38 .1) 1 .60" (40 .6) 1 .70" (43 .2) 1 .70" (43 .2) 1 .70" (43 .2) 2 .20" (55 .9) 2 .20" (55 .9) 2 .70" (68 .6) 2 .70" (68 .6) 2 .70" (68 .6) 2 .70" (68 .6) 2 .70" (68 .6) Nylon Inches (mm) C D Throat Dia. E A B C D Throat Dia. A/C* A/F* Dia. Ref. .46" (11 .7) .46" (11 .7) .46" (11 .7) .55" (14 .0) .55" (14 .0) .55" (14 .0) .55" (14 .0) .71" (18 .0) .66" (16 .8) .74" (18 .8) .74" (18 .8) .75" (19 .0) .80" (20 .3) .88" (22 .4) 1 .30" (33 .0) 1 .25" (31 .7) 1 .30" (33 .0) 1 .38" (35 .1) .32" (8 .1) .44" (11 .2) .44" (11 .2) .64" (16 .3) .64" (16 .3) .64" (16 .3) .82" (20 .8) 1 .02" (25 .9) 1 .01" (25 .7) 1 .26" (32 .0) 1 .38" (35 .1) 1 .50" (38 .1) 1 .92" (48 .8) 1 .94" (49 .3) 2 .32" (58 .9) 2 .38" (60 .5) 2 .54" (64 .5) 3 .00" (76 .2) .99" (25 .1) .99" (25 .1) 1 .00" (25 .4) 1 .11" (28 .2) 1 .40" (35 .6) 1 .29" (32 .8) 1 .40" (35 .6) 1 .81" (46 .0) 2 .28" (57 .9) 2 .28" (57 .9) 2 .28" (57 .9) 2 .97" (75 .4) 3 .24" (82 .4) 4 .05" (102 .9) 4 .34" (110 .2) 4 .86" (123 .4) 4 .34" (110 .2) 4 .86" (123 .4) .88" (22 .4) .88" (22 .4) .88" (22 .4) 1 .00" (25 .4) 1 .25" (31 .7) 1 .13" (28 .7) 1 .25" (31 .7) 1 .62" (41 .1) 2 .00" (50 .8) 2 .12" (53 .8) 2 .12" (53 .8) 2 .75" (69 .8) 3 .00" (76 .2) 3 .75" (95 .2) 4 .02" (102 .1) 4 .50" (114 .3) 4 .02" (102 .1) 4 .50" (114 .3) 1 .00" (25 .4) 1 .00" (25 .4) 1 .00" (25 .4) 1 .32" (33 .5) -- E A/C* A/F* 1 .10" (27 .9) 1 .10" (27 .9) 1 .10" (27 .9) 1 .50" (38 .1) -- .43" (10 .9) .43" (10 .9) .46" (11 .7) .53" (13 .5) -- .33" (8 .4) .45" (11 .4) .45" (11 .4) .58" (14 .7) -- .1 .00" (25 .4) 1 .00" (25 .4) 1 .00" (25 .4) 1 .25" (31 .7) -- .93" (23 .6) .93" (23 .6) .93" (23 .6) 1 .12" (28 .4) -- -- -- -- -- -- -- 1 .56" (39 .6) 1 .88" (47 .8) -- 1 .60" (40 .6) 1 .75" (44 .4) -- .55" (14 .0) .70" (17 .8) -- .77" (19 .6) 1 .01" (25 .7) -- 1 .44" (36 .6) 1 .84" (46 .7) -- 1 .31" (33 .3) 1 .63" (41 .4) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: *A/C-- Across Corners; A/F--Across Flats. A (Overall) Technical Information B Ref. E F C D Dimensions shown are approximate and are subject to change without notice. Dimensions in Inches (cm) www.hubbell-wiring.com T-93 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Cord Connectors Straight Hubbell Connectors Zinc-Plated Steel Inches (mm) F A B Stainless Steel Inches (mm) C D Throat Dia. E A B C D Throat Dia. E N.P.T. Form A/C* A/F* Ref. A/C* A/F* A/C* A/F* A/C* A/F* 1/4- 18 1 -- -- -- -- -- -- -- -18 1 1/2-14 1 1 .30" (33 .0) -- 1 .13" (28 .7) -- 1 .10" (27 .9) -- .54" (13 .7) -- .63" (16 .0) -- 1 .16" (29 .5) -- 1 .00" (25 .4) -- -- -- -- -- -- -- -- 3/4-14 3 1-111/2 3 1 .59" (40 .4) -- 1 .38" (35 .1) -- 1 .30" (33 .0) -- .56" (14 .2) -- .81" (20 .6) -- 1 .44" (36 .6) -- 1 .25" (31 .7) -- 1-111/2 4 1-111/2 5 2 .02" (51 .3) -- 1 .75" (44 .4) -- 1 .40" (35 .6) -- .70" (17 .8) -- 1 .03" (26 .2) -- 1 .88" (47 .8) -- 1 .63" (41 .4) -- 11/4-111/2 5 -- -- -- -- -- -- -- 11/2-111/2 5 -- -- -- -- -- -- -- 11/2-111/2 6 -- -- -- -- -- -- -- 2-111/2 6 -- -- -- -- -- -- -- 2-111/2 7 -- -- -- -- -- -- -- 21/2-8 7 -- .88" (22 .4) .88" (22 .4) 1 .00" (25 .4) 1 .25" (31 .7) 1 .13" (28 .7) 1 .25" (31 .7) 1 .38" (35 .1) 1 .69" (42 .9) 2 .15" (54 .6) 2 .19" (55 .6) 2 .19" (55 .6) 2 .83" (71 .9) 3 .07" (78 .0) 3 .89" (98 .8) -- .75" (19 .0) .75" (19 .0) -- 2 .99" (25 .1) 1 .00" (25 .4) 1 .10" (28 .2) 1 .40" (35 .6) 1 .29" (32 .8) 1 .40" (35 .6) 1 .54" (39 .1) 1 .95" (49 .5) 2 .46" (62 .5) 2 .48" (63 .0) 2 .48" (63 .0) 3 .04" (77 .2) 3 .32" (84 .3) 4 .18" (106 .2) -- .87" (22 .1) .87" (22 .1) -- 3/4-14 .45" (11 .4) .45" (11 .4) .64" (16 .3) .64" (16 .3) .64" (16 .3) .82" (20 .8) .89" (22 .6) 1 .02" (25 .9) 1 .02" (25 .9) 1 .27" (32 .3) 1 .39" (35 .3) 1 .52" (38 .6) 1 .92" (48 .8) 1 .99" (50 .5) -- .38" (9 .7) .45" (11 .4) -- 3 .42" (10 .7) .55" (14 .0) .55" (14 .0) .55" (14 .0) .55" (14 .0) .55" (14 .0) .70" (17 .8) .70" (17 .8) .70" (17 .8) .73" (18 .5) .74" (18 .8) .75" (19 .0) .78" (19 .8) .78" (19 .8) -- .46" (11 .7) .46" (11 .7) -- 1/2-14 .90" (22 .9) .90" (22 .9) 1 .20" (30 .5) 1 .50" (38 .1) 1 .20" (30 .5) 1 .40" (35 .6) 1 .40" (35 .6) 1 .60" (40 .6) 1 .70" (43 .2) 1 .70" (43 .2) 1 .70" (43 .2) 2 .20" (55 .9) 2 .20" (55 .9) 2 .70" (68 .6) -- .90" (22 .9) .90" (22 .9) -- 2 .88" (22 .4) .88" (22 .4) 1 .13" (28 .7) 1 .38" (35 .1) 1 .13" (28 .7) 1 .38" (35 .1) 1 .38" (35 .1) 1 .69" (42 .9) .88" (22 .4) .88" (22 .4) -- 1/2-14 .98" (24 .9) .98" (24 .9) 1 .27" (32 .3) 1 .55" (39 .4) 1 .27" (32 .3) 1 .55" (39 .4) 1 .55" (39 .4) 1 .92" (48 .8) 2 .40" (61 .0) 2 .40" (61 .0) 2 .40" (61 .0) 3 .06" (77 .7) 3 .06" (77 .7) 3 .95" (100 .3) -- 1 .01" (25 .7) 1 .01" (25 .7) -- -- -- -- -- -- -- -- 21/2-8 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 3-8 7 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 3-8 8 -- -- -- -- -- -- -- -- -- -- -- -- -- -- Technical Information Note: *A/C-- Across Corners; A/F--Across Flats. A (Overall) B Ref. E F C D T-94 Dimensions shown are approximate and are subject to change without notice. www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Cord Connectors 45 Hubbell Connectors F N.P.T. Form 1/2-14 2 3/4-14 3 1-111/2 4 11/2-111/2 5 11/2-111/2 5 Aluminum Inches (mm) A B C D E G Throat Across Across Ref. Ref. Dia. Corners Flats Dia. Zinc Plated Steel Inches (mm) A B C D Throat Ref. Ref. Dia. E Across Corners G Across Across Across Flats Corners Flats 2 .00" (50 .8) 2 .30" (58 .4) 2 .60" (66 .0) 3 .90" (99 .1) 3 .90" (99 .1) 1 .97" 1 .90" .55" .57" (50 .0) (48 .3) (14 .0) (14 .4) -- -- -- -- 1 .24" (31 .5) -- 1 .06" (26 .9) -- 1 .27" (32 .3) -- 1 .13" (28 .6) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1 .90" (48 .3) 2 .50" (65 .3) 2 .80" (71 .1) 3 .90" (9 .91) 3 .90" (99 .1) .55" (14 .0) .56" (14 .2) .70" (17 .8) .74" (18 .8) .74" (18 .8) .56" (14 .2) .75" (19 .0) 1 .00" (25 .4) 1 .25" (31 .7) 1 .50" (38 .1) 1 .27" (32 .3) 1 .48" (37 .6) 1 .69" (42 .9) 2 .45" (62 .2) 2 .45" (62 .2) 1 .10" (27 .9) 1 .28" (32 .5) 1 .50" (38 .1) 2 .13" (54 .0) 2 .13" (54 .0) 1 .13" (28 .6) 1 .38" (34 .9) 1 .75" (44 .4) 2 .31" (58 .7) 2 .31" (58 .7) Kellems(R) Wire Management Products Kellems(R) Wire Management Products 90 Hubbell Connectors F N.P.T. Form -18 1 1/2-14 2 3/4-14 3 1-111/2 4 11/4-111/2 5 11/2-111/2 5 2-111/2 6 Aluminum Inches (mm) A B C D E G Throat Across Across Ref. Dia. Corners Flats Dia. Zinc Plated Steel Inches (mm) A B C D Throat Ref. Dia. E Across Corners G Across Across Across Flats Corners Flats 1 .27" (32 .3) 1 .56" (39 .6) 1 .79" (45 .5) 2 .08" (52 .8) 3 .18" (80 .8) 3 .18" (80 .8) 3 .51" (89 .2) -- -- -- -- -- -- -- -- 1 .65" (41 .9) 1 .88" (47 .8) 2 .16" (54 .9) -- 2 .38" (60 .5) 2 .90" (73 .7) 3 .20" (81 .3) -- .55" (14 .0) .56" (14 .2) .70" (17 .8) -- .55" (13 .8) .77" (19 .4) 1 .00" (25 .4) -- 1 .29" (32 .8) 1 .52" (38 .6) 1 .72" (43 .7) -- 1 .13" (28 .7) 1 .33" (33 .8) 1 .50" (38 .1) -- 1 .27" (32 .3) 1 .55" (39 .2) 1 .92" (48 .8) -- 1 .13" (28 .6) 1 .38" (34 .9) 1 .69" (42 .8) -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2 .00" (50 .8) 2 .30" (58 .4) 2 .80" (71 .1) 3 .20" (81 .3) 4 .30" (109 .2) 4 .30" (109 .2) 5 .50" (139 .7) .46" (11 .7) .50" (12 .7) .56" (14 .2) .70" (17 .8) .73" (18 .5) .75" (19 .2) .80" (20 .3) .44" (11 .2) .55" (13 .9) .77" (19 .4) 1 .00" (25 .4) 1 .26" (32 .0) 1 .50" (38 .1) 1 .92" (48 .8) 1 .15" (29 .2) 1 .30" (33 .0) 1 .49" (37 .8) 1 .70" (43 .2) 2 .47" (62 .7) 2 .47" (62 .7) 2 .98" (75 .7) 1 .10" (27 .9) 1 .13" (28 .7) 1 .31" (33 .3) 1 .50" (38 .1) 2 .15" (54 .6) 2 .15" (54 .6) 2 .78" (70 .6) .88" (22 .2) 1 .13" (28 .6) 1 .38" (34 .9) 1 .75" (44 .4) 2 .31" (58 .7) 2 .31" (58 .7) 3 .00" (76 .2) 90 Hubbell Connectors Nylon Inches (mm) A B C F N.P.T. Form -18 1/2-14 1 2 3/4-14 3 1-111/2 4 Ref. -- 2 .50" (63 .5) 2 .81" (71 .4) 3 .30" (83 .8) -- .55" (14 .0) .56" (14 .2) .70" (17 .8) -- .58" (14 .6) .77" (19 .4) 1 .01" (25 .7) G -- 1 .23" (31 .2) 1 .42" (36 .1) 1 .82" (46 .2) -- 1 .12" (28 .2) 1 .29" (32 .8) 1 .60" (40 .6) -- 1 .32" (33 .4) 1 .56" (39 .6) 1 .88" (47 .6) Technical Information -- 1 .41" (35 .8) 1 .65" (41 .9) 1 .99" (50 .5) D E G Throat Across Across Dia. Corners Flats Dia. B Ref. B Ref. G A Ref. A E E C F Dimensions shown are approximate and are subject to change without notice. D Dimensions in Inches (cm) www.hubbell-wiring.com C F D T-95 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Cord Connectors A (Overall) Female Hubbell Connectors B Ref. E Aluminum Inches (mm) F A B Dia. Ref. A (Overall) F C E Across Corners Across Flats Form -18 1 .88" (22 .4) 1 .40" (35 .6) .56" (14 .2) .44" (11 .2) .94" (23 .9) .81" (20 .6) 1/2-14 2 1 .13" (28 .7) 1 .80" (45 .7) .56" (14 .2) .63" (16 .0) 1 .15" (29 .2) 1 .00" (25 .4) 3/4-14 2 1 .13" (28 .7) 2 .10" (53 .3) .75" (19 .0) .63" (16 .0) 1 .44" (36 .6) 1 .25" (31 .7) 1-111/2 4 1 .75" (44 .5) 2 .30" (58 .4) .88" (22 .4) 1 .10" (27 .9) 1 .88" (47 .8) 1 .63" (41 .4) 11/4-111/2 5 2 .31" (58 .7) 2 .80" (71 .1) .95" (24 .1) 1 .43" (36 .3) 2 .64" (67 .1) 2 .29" (58 .2) 11/2-111/2 5 2 .31" (58 .7) 2 .80" (71 .1) .95" (24 .1) 1 .43" (36 .3) 2 .64" (67 .1) 2 .29" (58 .2) B Ref. E D Throat Dia. N.P.T. D C (N.P.T. Thread Depth) C D Underground Feeder Connectors Aluminum Inches (mm) F A B C Nylon Inches (mm) D E A B C Thrt. N.P.T. Form Dia. Ref. Dia. Zinc-Plated Steel Inches (mm) D E A B C Thrt. A/C* A/F* Dia. Ref. Dia. D E Thrt. A/C* A/F* A/C* A/F* Ref. Dia. A/C* A/F* 1/2-14 2 1 .13" 1 .10" .55" .64" 1 .10" 1 .00" 1 .32" 1 .50" .55" .58" 1 .25" 1 .13" 1 .27" 1 .13" 1 .20" .55" .64" 1 .11" 1 .00" (28 .7) (27 .9) (14 .0) (16 .3) (27 .9) (25 .4) (33 .5) (38 .1) (14 .0) (14 .7) (31 .7) (28 .7) (32 .3) (28 .7) (30 .5) (14 .0) (16 .3) (28 .2) (25 .4) 3/4-14 2 1 .13" 1 .10" .55" .64" 1 .29" 1 .13" -- (28 .7) (27 .9) (14 .0) (16 .3) (32 .8) (25 .4) 3/4-14 3 1 .13" 1 .50" .55" .82" 1 .40" 1 .25" 1 .56" 1 .60" .56" .77" 1 .44" 1 .31" 1 .55" 1 .38" 1 .40" .56" .82" 1 .40" 1 .25" (28 .7) (38 .1) (14 .0) (20 .8) (35 .6) (31 .7) (39 .6) (40 .6) (14 .2) (19 .6) (36 .6) (33 .3) (39 .4) (35 .1) (35 .6) (14 .2) (20 .8) (35 .6) (31 .7) -- -- -- -- -- 1 .27" 1 .13" 1 .20" .55" .64" 1 .29" 1 .13" (32 .3) (28 .7) (30 .5) (14 .0) (16 .3) (32 .8) (28 .7) Note: *A/C - Across Corners; A/F - Across Flats. Low Profile Non-Metallic N.P.T., PG and Metric Thread Connectors Nylon Inches (mm) B F D C E Technical Information SEALING NUT A Recommended knockout size T-96 Hub Size A B C D E F N .P .T . 0 .670" (17 .0) 1 .41" (35 .8) 0 .48" (12 .4) 0 .21" (5 .3) 0 .83" (21 .0) 0 .55" (14 .0) 1/2 N .P .T . 0 .875" (22 .2) 1 .70" (43 .2) 0 .61" (15 .5) 0 .21" (5 .3) 0 .88" (24 .8) 0 .66" (16 .8) 3/4 N .P .T . 1 .068" (27 .1) 2 .00" (50 .8) 0 .62" (15 .7) 0 .25" (6 .3) 1 .30" (33 .0) 0 .85" (21 .6) 1 N .P .T . 1 .375" (35 .0) 2 .41" (61 .2) 0 .76" (19 .3) 0 .30" (7 .6) 1 .73" (43 .9) 1 .05" (26 .7) PG7 0 .492" (12 .5) 1 .16" (29 .5) 0 .32" (8 .1) 0 .21" (5 .3) 0 .63" (16 .0) 0 .48" (12 .4) PG9 0 .599" (15 .2) 1 .25" (31 .8) 0 .32" (8 .1) 0 .21" (5 .3) 0 .83" (21 .0) 0 .55" (14 .0) PG11 0 .733" (18 .6) 1 .48" (37 .6) 0 .38" (9 .7) 0 .21" (5 .3) 0 .94" (23 .9) 0 .70" (17 .8) PG13 .5 0 .804" (20 .4) 1 .53" (38 .9) 0 .41" (10 .4) 0 .21" (5 .3) 0 .98" (24 .9) 0 .66" (16 .8) PG16 0 .888" (22 .5) 1 .68" (42 .7) 0 .44" (11 .2) 0 .25" (6 .4) 1 .06" (27 .0) 0 .76" (19 .3) PG21 1 .15" (28 .3) 1 .89" (48 .0) 0 .52" (13 .2) 0 .25" (6 .4) 1 .30" (33 .0) .085" (21 .6) PG29 1 .47" (37 .30) 2 .23" (56 .6) 0 .58" (14 .7) 0 .30" (7 .6) 1 .73" (43 .9) 1 .05" (26 .7) PG36 1 .85" (47 .0) 2 .39" (60 .7) 0 .47" (11 .9) 0 .31" (7 .9) 2 .05" (52 .7) 1 .19" (30 .2) M12 0 .473" (12 .0) 1 .16" (29 .5) 0 .32" (8 .1) 0 .21" (5 .3) 0 .63" (16 .0) 0 .49" (12 .4) M16 0 .630" (16 .0) 1 .25" (31 .8) 0 .32" (8 .1) 0 .21" (5 .3) 0 .83" (21 .0) 0 .55" (14 .0) M20 0 .787" (20 .0) 1 .53" (38 .9) 0 .41" (10 .4) 0 .21" (5 .3) 0 .98" (24 .9) 0 .66" (16 .8) M25 0 .985" (25 .0) 1 .89" (48 .0) 0 .52" (13 .2) 0 .25" (6 .3) 1 .30" (33 .0) 0 .85" (21 .6) M32 1 .260" (32 .0) 2 .23" (56 .6) 0 .58" (14 .7) 0 .30" (7 .6) 1 .73" (43 .9) 1 .05" (26 .7) M40 1 .575" (40 .0) 2 .39" (60 .7) 0 .48" (12 .2) 0 .30" (7 .6) 2 .05" (52 .1) 1 .19" (30 .2) www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Cord Connectors 2 Conductors Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8 Approximate Diameter .25" (6.2) .31" (7.8) .33" (8.4) .37" (9.3) .38" (9.7) .40" (10.2) .54" (13.7) .62" (15.6) .68" (17.1) .81" (20.6) Black Black White White Blue Blue Brown Brown Yellow Orchid HC1004 HC1010 HC1016 HC1022 -- HC1032 -- -- -- -- -- -- -- HC1005 HC1011 HC1017 HC1022 -- HC1032 -- -- -- -- -- -- -- HC1005 HC1011 HC1017 HC1022 -- HC1032 -- -- -- -- -- -- -- HC1006 HC1012 HC1018 HC1023 HC1025 HC1033 HC1035 HC1039 -- -- -- -- -- HC1006 HC1012 HC1018 HC1023 HC1025 HC1033 HC1035 HC1039 -- -- -- -- -- -- -- -- HC1024 HC1026 HC1034 HC1036 HC1040 -- -- -- -- -- -- -- -- HC1024 HC1026 HC1034 HC1036 HC1040 -- -- -- -- -- -- -- -- -- HC1027 -- HC1037 HC1041 -- -- -- -- -- -- -- -- -- HC1028 -- HC1038 HC1042 HC1045 HC1050 HC1055 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Color N.P.T. Form S, SO, ST, STO Catalog Number* 1/4 1/2 1/2 1/2 3/4 3/4 1 1 11/4 11/2 11/2 2 2 1 1 1 2 3 2 3 4 5 5 5 6 6 7 HC1004 HC1010 HC1016 HC1022 -- HC1032 -- -- -- -- -- -- -- -- 21/2 3 7 7 -- -- Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100. F5 and larger will not be color coded. 3 Conductors Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8 Approximate Diameter .26" (6.5) .33" (8.3) .35" (8.9) .39" (9.8) .39" (9.9) .42" (10.7) .57" (14.4) .65" (16.4) .71" (18.0) .85" (21.5) Black White White Blue Blue Blue Brown Yellow Yellow Orchid HC1005 HC1011 HC1017 HC1022 -- HC1032 -- -- -- -- -- -- -- -- -- -- HC1006 HC1012 HC1018 HC1023 HC1025 HC1033 HC1035 HC1039 -- -- -- -- -- -- -- -- HC1006 HC1012 HC1018 HC1023 HC1025 HC1033 HC1035 HC1039 -- -- -- -- -- -- -- -- HC1006 HC1012 HC1018 HC1023 HC1025 HC1033 HC1035 HC1039 -- -- -- -- -- -- -- -- -- -- -- HC1024 HC1026 HC1034 HC1036 HC1040 -- -- -- -- -- -- -- -- -- -- -- -- HC1027 -- HC1037 HC1041 -- -- -- -- -- -- -- -- -- -- -- -- HC1027 -- HC1037 HC1041 -- -- -- -- -- -- -- -- -- -- -- -- HC1028 -- HC1038 HC1042 HC1045 HC1050 HC1055 -- -- -- -- -- Color N.P.T. 1 1 1 2 3 2 3 4 5 5 5 6 6 7 7 7 Catalog Number* HC1004 HC1010 HC1016 HC1022 -- HC1032 -- -- -- -- -- -- -- -- -- -- HC1005 HC1011 HC1017 HC1022 -- HC1032 -- -- -- -- -- -- -- -- -- -- Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100. F5 and larger will not be color coded. Dimensions in Inches (cm) www.hubbell-wiring.com T-97 Technical Information 1/4 1/2 1/2 1/2 3/4 3/4 1 1 11/4 11/2 11/2 2 2 21/2 3 Form S, SO, ST, STO Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Cord Connectors 2 Conductors Cord Type SVO, SV, SVT SJ, SJO, SJT, SJTO Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250 Approximate Diameter .94" (23.8) 1.08" (27.4) 1.17" (29.7) 1.27" (33.3) 1.44" (36.6) 1.52" (38.6) 1.65" (41.9) 1.77" (45.0) 1.92" (48.8) 2.16" (51.9) Gray Pink -- -- -- -- -- -- -- -- HC1049 HC1054 HC1059 HC1060 HC1065 -- -- -- -- -- -- -- -- -- -- -- HC1061 HC1066 -- -- -- -- -- -- -- -- -- -- -- HC1062 HC1067 -- -- -- -- -- -- -- -- -- -- -- HC1063 HC1068 -- -- -- -- -- -- -- -- -- -- -- HC1064 HC1069 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- HC1070 HC1076 HC1086 HC1071 HC1077 HC1087 HC1073 HC1079 HC1089 Color N.P.T. Form S, SO, ST, STO Catalog Number* 1/4 1/2 1/2 1/2 3/4 3/4 1 1 11/4 11/2 11/2 2 2 1 1 1 2 3 2 3 4 5 5 5 6 6 7 -- -- -- -- -- -- -- HC1043 HC1046 HC1051 HC1056 -- -- -- -- -- -- -- -- -- -- HC1044 HC1047 HC1052 HC1057 -- -- -- -- -- -- -- -- -- -- -- HC1048 HC1053 HC1058 -- -- -- 21/2 3 7 7 -- -- -- -- -- -- Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100. F5 and larger will not be color coded. 3 Conductors CordType SVO, SV, SVT SJ, SJO, SJT, SJTO Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250 Approximate Diameter 1.00" (25.4) 1.17" (29.7) 1.24" (31.5) 1.34" (34.0) 1.51" (38.4) 1.65" (41.9) 1.75" (44.5) 1.80" (48.0) 2.07" (52.6) 2.39" (60.7) Gray -- -- -- -- -- -- -- -- HC1048 HC1053 HC1058 -- -- -- -- -- -- -- -- -- -- -- -- -- HC1049 HC1054 HC1059 HC1060 HC1065 -- -- -- -- -- -- -- -- -- -- -- -- -- -- HC1062 HC1067 -- -- -- -- -- -- -- -- -- -- -- -- -- -- HC1063 HC1068 -- -- -- -- -- -- -- -- -- -- -- -- -- -- HC1064 HC1069 HC1070 HC1076 HC1086 -- -- -- -- -- -- -- -- -- -- -- -- -- HC1071 HC1077 HC1087 -- -- -- -- -- -- -- -- -- -- -- -- -- HC1073 HC1079 HC1089 -- -- -- -- -- -- -- -- -- -- -- -- -- HC1075 HC1081 HC1091 Color Technical Information N.P.T. Form 1/4 1/2 1/2 1/2 3/4 3/4 1 1 11/4 11/2 11/2 2 2 21/2 3 1 1 1 2 3 2 3 4 5 5 5 6 6 7 7 7 S, SO, ST, STO Catalog Number* -- -- -- -- -- -- -- HC1044 HC1047 HC1052 HC1057 -- -- -- -- -- -- -- -- -- -- -- -- -- HC1048 HC1053 HC1058 -- -- -- -- -- Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100. F5 and larger will not be color coded. T-98 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Cord Connectors 4 Conductors Cord Type SJ, SJO, SJT, SJTO Cord Size #18 #16 #14 #18 #16 #14 #12 #10 #8 Approximate Diameter .36" (9.0) .39" (9.8) .43" (10.8) .42" (10.7) .45" (11.4) .61" (15.5) .70" (17.8) .77" (19.4) .97" (24.6) Color White Blue Blue Blue Blue Brown Yellow Orchid Gray N.P.T. Form S, SO, ST, STO Catalog Number* 1/4 1 HC1005 HC1006 HC1006 HC1006 -- -- -- -- -- 1 HC1011 HC1012 HC1012 HC1012 -- -- -- -- -- 1/2 1 HC1017 HC1018 HC1018 HC1018 -- -- -- -- -- 1/2 2 HC1022 HC1023 HC1023 HC1023 HC1023 HC1024 -- -- -- 1/2 3 -- HC1025 HC1025 HC1025 HC1025 HC1026 HC1027 HC1028 -- 3/4 2 -- HC1033 HC1033 HC1033 HC1033 HC1034 -- -- -- 3/4 3 -- HC1035 HC1035 HC1035 HC1035 HC1036 HC1037 HC1038 1 4 -- HC1039 HC1039 HC1039 HC1039 HC1040 HC1041 HC1042 HC1043 1 5 -- -- -- -- -- -- -- -- HC1046 11/4 5 -- -- -- -- -- -- -- -- HC1051 11/2 5 -- -- -- -- -- -- -- -- HC1056 11/2 6 -- -- -- -- -- -- -- -- -- 2 6 -- -- -- -- -- -- -- -- -- 2 7 -- -- -- -- -- -- -- -- -- 21/2 7 -- -- -- -- -- -- -- -- -- 3 7 -- -- -- -- -- -- -- -- -- Kellems(R) Wire Management Products Kellems(R) Wire Management Products Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100. F5 and larger will not be color coded. 5 Conductors Cord Type S, SO, ST, STO Cord Size #18 #16 #14 #12 #10 #8 #6 Approximate Diameter .50" (12.7) .54" (13.7) .70" (17.7) .76" (19.3) .83" (21.1) 1.06" (26.9) 1.18" (30.0) Color Blue Brown Yellow Orchid Orchid Pink N.P.T. Form Catalog Number* 2 HC1023 HC1024 -- -- -- -- -- 1/2 3 HC1025 HC1026 HC1027 HC1028 HC1028 -- -- 3/4 2 HC1033 HC1034 -- -- -- -- -- 3/4 3 HC1035 HC1036 HC1037 HC1038 HC1038 -- -- 1 4 HC1039 HC1040 HC1041 HC1042 HC1042 HC1044 -- 1 5 -- -- -- HC1045 HC1045 HC1047 HC1048 11/4 5 -- -- -- HC1050 HC1050 HC1052 HC1053 11/2 5 -- -- -- HC1055 HC1055 HC1057 HC1058 Technical Information 1/2 Note * Must add prefix, see Note 1; suffix, see Note 2, on page T-100. F5 and larger will not be color coded. Dimensions in Inches (cm) www.hubbell-wiring.com T-99 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Cord Connectors 4 Conductors Cord Type SJ, SJO, SJT, SJTO Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 Approximate Diameter .94" (23.8) 1.08" (27.4) 1.17" (29.7) 1.27" (33.3) 1.44" (36.6) 1.52" (38.6) 1.65" (41.9) 1.77" (45.0) 1.92" (48.8) Color Pink N.P.T. Form S, SO, ST, STO Catalog Number* 1/4 1 -- -- -- -- -- -- -- -- -- 1 -- -- -- -- -- -- -- -- -- 1/2 1 -- -- -- -- -- -- -- -- -- 1/2 2 -- -- -- -- -- -- -- -- -- 1/2 3 -- -- -- -- -- -- -- -- -- 3/4 2 -- -- -- -- -- -- -- -- -- 3/4 3 -- -- -- -- -- -- -- -- -- 1 4 HC1044 -- -- -- -- -- -- -- -- 1 5 HC1047 HC1049 HC1049 -- -- -- -- -- -- 11/4 5 HC1052 HC1054 HC1054 -- -- -- -- -- -- 11/2 5 HC1057 HC1059 HC1059 -- -- -- -- -- -- 11/2 6 -- HC1060 HC1060 HC1061 HC1063 HC1064 -- -- -- 2 6 -- HC1064 HC1065 HC1066 HC1068 HC1069 -- -- -- 2 7 -- -- -- -- -- HC1070 HC1071 HC1073 HC1074 21/2 7 -- -- -- -- -- HC1076 HC1077 HC1079 HC1080 3 7 -- -- -- -- -- HC1086 HC1087 HC1089 HC1090 Note: * Must add prefix, see Note 1; suffix, see Note 2, below. F5 and larger will not be color coded. Note: Technical Information 1. Add the proper prefix to the HC number to identify the type of connector desired: SHC = Straight Hubbell Connector NHC = 90 Hubbell Connector FHC = Female Hubbell Connector VHC = 45 Hubbell Connector 2. Add the proper suffix to identify material desired: Aluminum = No suffix Zinc-Plated Steel = ZP Corrosion Resistant Nylon = CR Stainless Steel = SS T-100 3. This chart is a general guide to assist in the selection of Hubbell Cord Connectors for various cord sizes . The Hubbell Cord Connector catalog numbers selected, have been inserted into spaces which in our judgment represent the best cord connector which will fit the listed cord size . The diameters of the cords are approximate and may vary depending on the manufacturer . It is suggested that the appropriate cord manufacturer's dimension chart be consulted for exact dimensions . 4. Cable jacket may have to be stripped to allow conductors to pass through connector body . www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Locknuts and Sealing O-Rings N.P.T. Thread Locknuts Zinc-Plated Steel N.P.T. Hub Size A Inside Dia. inches (mm) B Outside Dia. inches (mm) C Thk. inches (mm) Steel Catalog Number 1/2 3/4 1 11/4 11/2 1/2"-14 3/4"-14 1"-111/2 11/4"-111/2 11/2"-111/2 1 .14" 1 .43" 1 .77" 2 .28" 2 .60" .09" .11" .13" .13" .13" 00322001LPK50 00322002LPK50 00322003LPK50 00322004LPK50 00322005LPK50 (29 .0) (36 .3) (45 .0) (57 .9) (66 .0) (2 .3) (2 .8) (3 .3) (3 .3) (3 .3) B Maximum Diameter C Minimum Thk. A Thread Size (N.P.S.) Metal Clad Sealing O-Rings - Sizes 1/2 - 4 Zinc-Plated Steel with Neoprene Ring N.P.T. Hub Size A Inside Dia. inches (mm) B Outside Dia. inches (mm) C Thk. inches (mm) Catalog Number 1/2 3/4 1 11/4 11/2 2 .80" 1 .00" 1 .25" 1 .61" 1 .84" 2 .31" 1 .08" 1 .34" 1 .63" 2 .00" 2 .36" 2 .83" .16" .16" .16" .16" .16" .16" 20509001 20509002 20509003 20509004 20509005 20509006 (20 .3) (25 .4) (31 .6) (40 .9) (46 .7) (58 .7) (27 .4) (34 .0) (41 .4) (50 .8) (59 .9) (71 .9) Chrome Plated Steel with Neoprene Ring 21/2 2 .91" (73 .9) 3 .44" (87 .4) 3 3 .52" (89 .4) 4 .08" (103 .6) (3 .2) (3 .2) (3 .2) (3 .2) (3 .2) (3 .2) A Kellems(R) Wire Management Products Kellems(R) Wire Management Products B C .24" .24" (6 .1) (6 .1) 20509007 20509008 Nylon PG Thread Locknuts PG Thread Size A inches (mm) B inches (mm) C inches (mm) Catalog Number PG7 PG9 PG11 PG13 .5 PG16 PG21 PG29 PG36 .75" .86" .94" 1 .06" 1 .18" 1 .41" 1 .81" 2 .24" (19 .1) (21 .8) (23 .9) (26 .9) (30 .0) (35 .8) (46 .0) (56 .9) .80" .91" 1 .03" 1 .14" 1 .30" 1 .54" 2 .00" 2 .50" .22" .22" .22" .24" .25" .25" .25" .25" LNP7BPK100 LNP9BPK100 LNP11BPK100 LNP13BPK100 LNP16BPK100 LNP21BPK100 LNP29BPK25 LNP36BPK25 (20 .3) (23 .2) (26 .2) (29 .0) (33 .0) (39 .1) (50 .8) (63 .5) (5 .6) (5 .6) (5 .6) (6 .1) (6 .1) (6 .1) (6 .1) (6 .1) B A C PG Thread Size A inches (mm) B inches (mm) C inches (mm) Catalog Number M12 M16 M20 M25 M32 M40 .75" .87" 1 .06" 1 .38" 1 .61" 1 .97" (19 .1) (22 .09) (27 .0) (35 .1) (40 .9) (50 .0) .82" .98" 1 .18" 1 .54" 1 .80" 2 .18" .22" .22" .25" .28" .28" .28" LNM12BPK100 LNM16BPK100 LNM20BPK100 LNM25BPK100 LNM32BPK100 LNM40BPK100 (20 .8) (25 .0) (30 .0) (39 .1) (45 .7) (55 .4) (5 .6) (5 .6) (6 .4) (7 .1) (7 .1) (7 .1) Technical Information Nylon Metric Thread Locknuts Dimensions shown are approximate and are subject to change without notice. Dimensions in Inches (cm) www.hubbell-wiring.com T-101 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Hubbell Juniors(R) Miniature Nylon Cord Connectors Hubbell Juniors(R) Material Nylon (connectors and Neoprene (bushings) Operating Temperature Range GOTCHA(R) rings) -40F to +225F (-40C to +107C) -30F to +240F (-34C to +115C) Due to the limiting factors of nylon and neoprene, any complete liquidtight Hubbell Junior will continuously perform in the range of -30F to +225F (-34C to +107C). Snap-In continuously performs -40F to +225F (-40C to +107C). Flammability Hubbell Juniors have a UL 94V-2 rating . Certifications Product Agency Liquidtight and Liquidtight with Spiral UL Listed . CSA Certified . UL Recognized . CSA Certified . Snap-In Knockout Holes 1/4 1/2 .54"- .57" (13 .7-14 .5) .67"- .70" (17 .0-17 .8) .86"- .91" (21 .8-23 .1) Technical Information N.P.T. Hub Size Knockout Hole Recommended Min. to Max. inches (mm) Dimensions shown are approximate and are subject to change without notice . T-102 www.hubbell-wiring.com Dimensions in Inches (cm) Technical Information Hubbell Juniors(R) Miniature Nylon Cord Connectors Snap-In Diameter Range Inches (mm) For Chas. Thk. (Max.) Inches (mm) Required Hole Size A B Inches Inches (mm) (mm) Dimensional Specifications C D Inches Inches (mm) (mm) E Inches (mm) F Inches (mm) G Inches (mm) .22"- .27" (5 .6-6 .9) .10" (2 .5) .50" (12 .7) .45" (11 .4) .28" (7 .1) .28" (7 .1) .54" (13 .7) .12" (3 .0) 1 .84" (44 .2) .28"- .32" (7 .1-8 .1) .10" (2 .5) .50" (12 .7) .47" (11 .9) .28" (7 .1) .33" (8 .4) .59" (15 .0) .12" (3 .0) 1 .84" (44 .2) .30"- .36" (7 .6-9 .1) .13" (3 .3) .63" (16 .0) .55" (14 .0) .36" (9 .1) .37" (9 .4) .65" (16 .5) .14" (3 .6) 2 .18" (55 .4) .32"- .43" (8 .1-10 .9) .13" (3 .3) .75" (19 .0) .66" (16 .8) .45" (11 .4) .44" (11 .2) .75" (19 .1) .14" (3 .6) 2 .60" (66 .0) G C D F E A Chassis Thickness Max B Kellems(R) Wire Management Products Kellems(R) Wire Management Products B Liquidtight F A B C N.P.T. Dia. Inches (mm) Ref. Inches (mm) 1/4-18 .65" (16 .5) -18 1/2-14 E C Inches (mm) D Throat Dia. Inches (mm) Across Corners Inches (mm) 1 .30" (33 .0) .40" (10 .2) .29" (7 .4) .65" (16 .5) .60" (15 .2) .81" (20 .6) 1 .44" (36 .6) .41" (10 .4) .36" (9 .1) .81" (20 .6) .75" (19 .1) 1 .00" (25 .4) 1 .56" (39 .6) .46" (11 .7) .45" (11 .4) .99" (25 .1) .92" (23 .4) Across Flats Inches (mm) D A F E Liquidtight with Spiral A B C E Inches (mm) D Throat Dia. Inches (mm) Inches (mm) F Across Corners Inches (mm) N.P.T. Dia. Inches (mm) Ref. Inches (mm) Across Flats Inches (mm) 1/4-18 .65" (16 .5) 2 .55" (64 .8) .40" (10 .2) .29" (7 .4) .27" (6 .9) .65" (16 .5) .60" (15 .2) -18 .81" (20 .6) 3 .10" (78 .7) .41" (10 .4) .36" (9 .1) .35" (8 .9) .81" (20 .6) .75" (19 .1) 1/2-14 1 .00" (25 .4) 3 .72" (94 .5) .46" (11 .7) .45" (11 .4) .45" (11 .4) .99" (25 .1) .92" (23 .4) B A C E D G F Dimensions shown are approximate and are subject to change without notice . Dimensions in Inches (cm) www.hubbell-wiring.com T-103 Technical Information G Kellems(R) Wire Management Products Kellems(R) Wire Management Products PolyTuff(R) I Non-Metallic Liquidtight Conduit Features and Benefits PolyTuff(R) I Conduit-Gray Rigid PVC core bonded to flexible PVC jacket All nonmetallic construction ends metal fatigue and separation problems UL Listed and CSA Certified PolyTuff(R) I Non-Metallic Liquidtight Conduit Cuts cleanly with a knife or PVC cutter so there are no jagged metal edges IP66 SUITABILITY PolyTuff(R) I Conduit Trade Size (metric designator) Feet (m) Catalog Number (12) 100 (30 .5) G1038 1/2 (16) 100 (30 .5) G1050 3/4 (21) 100 (30 .5) G1075 1 (27) 100 (30 .5) G1100 11/4 (35) 100 (30 .5) G1125 11/2 (41) 50 (15 .2) G1150 2 (53) 50 (15 .2) G1200 Note: See pages T-68, T-69, T-107 and T-109 for approved fittings. See pages T-110 to T-111 for additional technical data and dimensional drawings. T-104 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products PolyTuff(R) II Non-Metallic Liquidtight Tubing Features and Benefits PolyTuff(R) II Tubing-Black PVC core with corrugated walls bonded to PVC jacket Handles twists, turns, bends, switchbacks and straightaways with ease All nonmetallic construction ends fatigue and separation problems Can be cut with a knife or PVC cutters UL Recognized and CSA Certified PolyTuff(R) II Non-Metallic Liquidtight Tubing IP66 SUITABILITY PolyTuff(R) II Tubing Trade Size (metric designator) Feet (m) Catalog Number 1/4 (10) 100 (30 .5) B2025 (12) 100 (30 .5) B2038 1/2 (16) 100 (30 .5) B2050 3/4 (21) 100 (30 .5) B2075 1 (27) 100 (30 .5) B2100 11/4 (35) 100 (30 .5) B2125 11/2 (41) 50 (15 .2) B2150 2 (53) 50 (15 .2) B2200 Note: See page T-107 for approved fittings. See pages T-110 to T-111 for additional technical data and dimensional drawings. Dimensions in Inches (cm) www.hubbell-wiring.com T-105 Kellems(R) Wire Management Products PolyTuff(R) Non-Metallic Liquidtight Fittings Kellems(R) Wire Management Products PolyTuff(R) Non-Metallic Liquidtight Fittings Features and Benefits Nylon two-piece swivel body enables fitting to twist from 0 to 90 Non-integral ferrule provides conduit seal and superior pullout protection Neoprene O-ring provides liquidtight seal at hub or enclosure Nylon compression nut has a tapered dome to tighten ferrule onto conduit T-106 Nylon locknut fastens connector securely to enclosure and provides superior corrosion resistance www.hubbell-wiring.com Dimensions in Inches (cm) PolyTuff(R) Non-Metallic Liquidtight Fittings UL Listed to Type 4X, 12 and 13 Straight with Male Non-Metallic Liquidtight Fittings Trade Size (metric designator) Black Catalog Number Gray Catalog Number 1/4 (6) (9) 1/2 (13) 3/4 (19) 1 (25) F2025 P038NBKA P050NBKA P075NBKA P100NBKA -- P038NGYA P050NGYA P075NGYA P100NGYA 11/4 (32) 11/2 (38) 2 (51) P125NBK P150NBK P200NBK P125NGY P150NGY P200NGY P075NGYA Note: Fittings are to be used with PolyTuff I and PolyTuff II. See page T-113 for additional technical data and dimensional drawings. " Liquidtight conduit fitting have 1/2 N.P.T. male threads. Kellems(R) Wire Management Products Kellems(R) Wire Management Products P125NGY SwivelLok(R) Multi-Position with Male Non-Metallic Liquidtight Fittings Trade Size (metric designator) Black Catalog Number Gray Catalog Number (9) 1/2 (13) 3/4 (19) 1 (25) PS0389NBK PS0509NBK PS0759NBK PS1009NBK PS0389NGY PS0509NGY PS0759NGY PS1009NGY Note: Fittings are to be used with PolyTuff I and PolyTuff II. See page T-113 for additional technical data and dimensional drawings. " Liquidtight conduit fitting have 1/2 N.P.T. male threads. PS0509NGY - SwivelLok(R) PolyTuff(R) Non-Metallic Liquidtight Fittings Fixed 90Fittings for Non-Metallic Conduit Trade Size (metric designator) Black Catalog Number Gray Catalog Number 1/4 (6) (9) 1/2 (13) 3/4 (19) 1 (25) 11/4 (32) F20259 P0389NBK P0509NBK P0759NBK P1009NBK P1259NBK -- P0389NGY P0509NGY P0759NGY P1009NGY P1259NGY Note: Fittings are to be used with PolyTuff I and PolyTuff II. See page T-113 for additional technical data and dimensional drawings. " Liquidtight conduit fitting have 1/2 N.P.T. male threads. P1259NGY SwivelLok(R) Flexible Conduit Kit Trade Size (metric designator) Fitting and Conduit Catalog Number 1/2 (13) 3/4 (19) 2 PS0509NGY, 6' G1050 2 PS0759NGY, 6' G1075 PS05GYKIT PS07GYKIT Note: See page T-113 for additional technical data and dimensional drawings. PS05GYKIT Dimensions in Inches (cm) www.hubbell-wiring.com T-107 Kellems(R) Wire Management Products Kellems(R) Wire Management Products Metallic Liquidtight Conduit Fittings Features and Benefits Hexagonal, screw-machined steel thru 1", and malleable iron on larger sizes . Nut compresses gland-ring onto conduit Metallic Liquidtight Conduit Fittings Split, nylon, gland-ring compresses conduit onto ferrule Non-integral, reusable steel, ferrule is easily installed, to seal conduit Threaded one-piece steel body Tapered, machined threads fasten securely and provide additional liquidtight sealing Optional insulated and non-insulated throat Nylon gasket provides liquidtight seal at hub Locknut has hardened steel tangs to grip securely T-108 www.hubbell-wiring.com Dimensions in Inches (cm) Metallic Liquidtight Conduit Fittings Straight Conduit Fitting Trade Size (metric designator) Insulated Non-Insulated (9) 1/2 (13) 3/4 (19) 1 (25) H0381 H0501 H0751 H1001 H038 H050 H075 H100 11/4 (32) 11/2 (38) 2 (51) 21/2 (63) H1251 H1501 H2001 H2501 H125 H150 H200 H250 3 (76) 31/2 (89) 4 (102) H3001 H3501 H4001 H300 H350 H400 Straight with Male Hubbell Conduit Fitting H050 Note: " Liquidtight conduit fitting have 1/2 N.P.T. male threads. For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. See page T-114 for additional technical data. Kellems(R) Wire Management Products Kellems(R) Wire Management Products 45 Conduit Fitting Trade Size (metric designator) Insulated Non-Insulated (9) 1/2 (13) 3/4 (19) 1 (25) H03841 H05041 H07541 H10041 H0384 H0504 H0754 H1004 11/4 (32) 11/2 (38) 2 (51) H12541 H15041 H20041 H1254 H1504 H2004 Note: " Liquidtight conduit fitting have 1/2 N.P.T. male threads. For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. See page T-114 for additional technical data. 45 Angle with Male Hubbell Conduit Fitting H0504 90 Conduit Fitting Insulated Non-Insulated (9) 1/2 (13) 3/4 (19) 1 (25) H03891 H05091 H07591 H10091 H0389 H0509 H0759 H1009 11/4 (32) 11/2 (38) 2 (51) 21/2 (63) 3 (76) 4 (102) H12591 H15091 H20091 H25091 H30091 H40091 H1259 H1509 H2009 H2509 H3009 H4009 Note: " Liquidtight conduit fitting have 1/2 N.P.T. male threads. For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit. See page T-114 for additional technical data. Dimensions in Inches (cm) www.hubbell-wiring.com 90 Angle with Male Hubbell Conduit Fitting H0509 T-109 Metallic Liquidtight Conduit Fittings Trade Size (metric designator) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Non-Metallic Liquidtight Conduit and Tubing PolyTuff I Conduit Operating Temperature Range Wet environment Oil environment Dry environment 0F to +140F (-18C to +60C) . 0F to +158F (-18C to +70C) . 0F to +176F (-18C to +80C) . Certifications UL Listed UL Standard 1660 . Sunlight resistant approved for outdoor use, direct burial . Meets requirements of NEC . CSA Certified Voltage Rating Maximum 600V . Material Conduit Co-extruded rigid and flexible PVC . PolyTuff II Tubing Operating Temperature Range Operating environment 0F to +140F (-18C to +60C) . Certifications UL Recognized CSA Certified Voltage Rating Maximum Same as wire insulation rating . Material Tubing Co-extruded rigid and flexible PVC . Technical Information PolyTuff I Conduit PolyTuff II Tubing Trade Size (metric designator) Conduit ID/OD Inches (mm) Bend Radius Inches (mm) (12) 1/2 (16) 3/4 (21) 1 (27) 11/4 (35) 11/2 (41) 2 (53) .49"/ .70" .63"/ .83" .83"/1 .04" 1 .05"/1 .30" 1 .40"/1 .65" 1 .59"/1 .88" 2 .03"/2 .36" 2 .00" 3 .00" 4 .00" 5 .00" 6 .30" 7 .50" 10 .00" T-110 (12 .6/17 .8) (16 .1/21 .1) (21 .1/26 .4) (26 .0/33 .1) (35 .4/41 .8) (40 .3/47 .8) (51 .6/59 .9) (50 .8) (76 .2) (101 .6) (217 .0) (158 .8) (190 .5) (254 .0) Trade Size (metric designator) Conduit ID/OD Inches (mm) Bend Radius Inches (mm) 1/4 (10) (12) 1/2 (16) 3/4 (21) 1 (27) 11/4 (35) 11/2 (41) 2 (53) .36"/ .57" .49"/ .70" .63"/ .83" .83"/1 .04" 1 .05"/1 .30" 1 .40"/1 .65" 1 .59"/1 .88" 2 .03"/2 .36" 1 .50" 2 .00" 2 .00" 3 .00" 3 .00" 5 .00" 5 .00" 5 .00" www.hubbell-wiring.com (9 .3/14 .5) (12 .6/17 .8) (16 .1/21 .1) (21 .1/26 .4) (26 .0/33 .1) (35 .4/41 .8) (40 .3/47 .8) (51 .6/59 .9) (38 .1) (50 .8) (50 .8) (76 .2) (76 .2) (127 .0) (127 .0) (127 .0) Dimensions in Inches (cm) Technical Information Non-Metallic Liquidtight Conduit and Tubing PolyTuff I and II Conduit/Tubing; PVC Chemical Resistance Chemical Conc* Temp. 70F 150F 21C 66C Temp. Conc* 70F 150F 21C 66C Chemical Chemical Temp. Conc* 70F 150F 21C 66C D B C D A C D C D D B C Coconut Oil Corn Oil Cottonseed Oil Creosote Cresol Crysylic Acid C A C D C D D B D D D D Lubricating Oils Magnesium Chloride Magnesium Hydroxide Magnesium Sulfate Malathion 50 in Aromatics Malic Acid A A A A D A A A A A D A Aluminum Chloride Aluminum Sulfate (Alums) Ammonia (Anhydrous Liquids) Ammonia (Aqueous) Ammoniated Latex Ammonium Chloride A A D A A A A A D A C A Cyclohexane DDT Weed Killer Dibutyl Phthalate Diesel Oils Diethylene Glycol Diethyl Ether B A D C B A C C D D C C Methyl Acetate Methyl Alcohol Methyl Bromide Methyl Ethyl Ketone Methylene Chloride Mineral Oil D C D D D D C D D D Ammonium Hydroxide Amyl Acetate Aniline Oils Aromatic Hydrocarbons Asphalt A D D D D A D D D D C D C D A A A D D D C C D Monochlorobenezene Muriatic Acid (see Hydrochloric Acid) Naphtha Naphthalene Nitric Acid 10% Nitric Acid 35% A C D B C A A A D D D B C D A ASTM Fuel A ASTM Fuel B ASTM #1 Oil ASTM #3 Oil Barium Chloride Barium Sulfide Barium Hydroxide Di-isodecyl Phthalate Dioctyl Phthalate Dow General Weed Killer (Phenol) Dow General Weed Killer (H2O) Ethyl Alcohol Ethylene Dichloride C D A A D D B C Ethylene Glycol Ferric Chloride Ferric Sulfate Ferrous Chloride Ferrous Sulfate Formaldehyde B A A A A D C A A A A D Nitric Acid Oleic Acid Oleum Oxalic Acid Pentachlorophenol in Oil Pentane D A D A B C D C D A C D Benzene (Benzol) Benzine (Petroleum Ether) Black Liquor Bordeaux Mixture Boric Acid Butyl Acetate D C A A A D D C A A A D Fuel Oil Furfural Gallic Acid Gasoline (Hi Test) Glycerine Grease B C A C A A C C A D A C Perchloroethylene Petroleum Ether Phenol Phosphoric Acid Pitch Potassium Hydroxide B C A A A C C C A A B D Butyl Alcohol Calcium Hydroxide Calcium Hypochlorite Carbolic Acid (Phenol) Carbon Dioxide Carbon Disulfide B A A B A D C A A C A D Green Sulfate Liquor Heptachlor in Petroleum Solvents Heptane Hexane Hydrobromic Acid Hydrochloric Acid 10% A A C C A A A C D D A A Sodium Cyanide Stoddard Solvent Styrene Sulfur Dioxide (liquid) Sulfuric Acid Sulfuric Acid A D D D A D A D D D B D Carbon Tetrachloride Carbonic Acid Casein Caustic Soda Chlorine Gas (wet) Chlorine Gas (dry) D A A A D D D A C B D D Hydrochloric Acid Hydrofluoric Acid Hydrofluorosilicic Acid Hydrofluorosilicic Acid Hydrogen Peroxide Iso-Octane C D A A A C C D A A B C Sulfurous Acid Tall Oil Tannic Acid Toluene Trichlorethylene Triethanol Amine B D A D D C C D A D D D Chlorine (water solution) Chlorobenzene Chlorinated Hydrocarbons Chromic Acid Citric Acid Coal Tar C D D B A D D D D C A D Isopropyl Acetate Isopropyl Acid Jet Fuels (JP-3, and 5) Kerosene Ketones Linseed Oil D B C C D A D C D C D A Tricresyl Phosphate (Skydrol) Turpentine Vinegar Vinyl Chloride Water White Liquor D C A D A A D D B D A A Xylene Zinc Chloride Zinc Sulfate D A A D A A 40% 70% 10% Note: * Conc. - Concentration. (All ratings apply to concentrated or saturated solutions unless otherwise specified.) Chemical resistance ratings are based upon information supplied by the raw material manufacturers. Use as a general guide only - samples should be tested by user under actual conditions. Rating Code A-Excellent service No harmful effect to reduce service life . Suitable for continuous service . B-Good service life. Moderate to minor effect . Good for intermittent service . Generally suitable for continuous service . Dimensions in Inches (cm) 70% 10% 50% 50% 98% C-Fair or limited service. Depends on operating conditions . Generally suitable for intermittent service . Not recommended for continuous service . D-Unsatisfactory service. Not recommended . www.hubbell-wiring.com T-111 Technical Information Acetate Solvents Acetic Acid Acetic Acid (Glacial) Acetone Acrylontrile Alcohols (Aliphatic) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Non-Metallic Liquidtight Fittings PolyTuff Fittings Operating Temperature* Nylon (Body, Nut, Gripping Ring and Locknut) Neoprene (Sealing Ring) -40F to +225F (-40C to +107C) . -30F to +240F (-34C to +116C) . Flammability Fire Gas Toxicity Product Testing Nylon PolyTuff Fittings have a UL 94V-2 rating . Certifications UL Listed CSA Certified UL50 Type 4X, 12 and 13 . PolyTuff I Fittings, Poly Tuff II Fittings . Liquidtight Fittings Operating Temperature** Steel/Malleable Iron (Nut, Body, Ferrule) Nylon (Gland Ring) -60F to +1000F (-51C to +538C) . -40F to +225F (-40C to +107C) . Hazardous Locations - NEC Reference Class I, Div . 2 - 501-10(A)(3)B Class II, Div . 1 - 502-10(A)(2) Class II, Div . 2 - 502-10(A)(3) Class III, Div . 1 - 503-10(A)(2) Class III, Div . 2 - 503-10(B) Certifications UL Listed CSA Certified Technical Information Note: * Due to the limiting factors of nylon and neoprene, PolyTuff Fittings will continuously perform in the range -30F to +225F (-34C to +107C). ** Due to the limiting factors of nylon, metallic liquidtight flexible conduit fittings will continuously perform in the range of -40F to +225F (-40C to +107C). T-112 www.hubbell-wiring.com Dimensions in Inches (cm) Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Non-Metallic Liquidtight Fittings E Straight with Male Non-Metallic Liquidtight Fittings Trade Size (md**) A B C D Throat Dia. 1/4 (10) (12) 1/2 (16) 3/4 (21) 1 (27) 11/4 (35) 11/2 (41) 2 (53) .93" (23 .6) 1 .14" (29 .0) 1 .30" (33 .0) 1 .53" (38 .9) 1 .80" (45 .7) 2 .20" (55 .9) 2 .49" (63 .2) 3 .05" (77 .4) 1 .45" (36 .8) 1 .63" (41 .4) 2 .14" (54 .4) 2 .22" (56 .4) 2 .32" (58 .9) 2 .15" (54 .6) 2 .35" (59 .7) 2 .51" (63 .6) .39" (9 .9) .57" (14 .5) .57" (14 .5) .58" (14 .7) .72" (18 .3) .74" (18 .8) .76" (19 .3) .79" (20 .1) .32" (8 .1) .42" (10 .7) .55" (14 .0) .74" (18 .8) .96" (24 .4) 1 .30" (33 .0) 1 .46" (37 .1) 1 .90" (48 .3) E A/C* A/F* A Dia. .86" (Dia .) (21 .8) 1 .41" (35 .8) 1 .41" (35 .8) 1 .85" (47 .0) 1 .94" (49 .3) 2 .38" (60 .5) 2 .63" (66 .8) 3 .13" (79 .5) 1 .30" (33 .0) 1 .30" (33 .0) 1 .53" (38 .9) 1 .80" (45 .7) 2 .18" (55 .4) 2 .43" (61 .7) 2 .93" (74 .4) D C B Sizes: 1/4", 11/4", 11/2", 2" E A D C B Note: * A/C = Across Corners A/F = Across Flats. ** md = metric designator. Sizes: 3/8", 1/2", 3/4", 1" 90 with Male Non-Metallic Liquidtight Fittings Trade Size (md**) A 1/4 (10) 11/4 (35) .93" (23 .6) 2 .21" (56 .1) B C 1 .88" (47 .8) 3 .57" (90 .7) .39" (9 .9) .74" (18 .9) D Throat Dia. .32" (8 .1) 1 .30" (33 .0) E A/C* B A/F* .86"(Dia .) (21 .8) 2 .38" (60 .5) 2 .18" (55 .4) A Dia. E Note: * A/C = Across Corners A/F = Across Flats. ** md = metric designator. SwivelLok(R) Multi-Position Liquidtight Fittings Trade Size (md**) A (12) 1/2 (16) 3/4 (21) 1 (27) 1 .30" (33 .0) 1 .30" (33 .0) 1 .53" (38 .9) 1 .80" (45 .7) B C 3 .27" (83 .1) 3 .27" (83 .1) 3 .66" (93 .0) 4 .00" (101 .6) .57" (14 .5) .57" (14 .5) .58" (15 .7) .72" (18 .3) D .55" (14 .0) .55" (14 .0) .74" (18 .8) .96" (24 .4) E C F 1 .43" (36 .3) 1 .43" (36 .3) 1 .59" (40 .4) 1 .84" (46 .7) G 2 .00" (50 .8) 2 .00" (50 .8) 2 .23" (56 .6) 2 .30" (58 .4) D A/C* A/F* 1 .41" (35 .8) 1 .41" (35 .8) 1 .65" (41 .9) 1 .94" (49 .3) 1 .30" (33 .0) 1 .30" (33 .0) 1 .53" (38 .9) 1 .80" (45 .7) A F G D C E 90 Position Dimensions in Inches (cm) B 45 Position www.hubbell-wiring.com Straight Position T-113 Technical Information Note: * A/C = Across Corners A/F = Across Flats. ** md = metric designator. Kellems(R) Wire Management Products Kellems(R) Wire Management Products Technical Information Metallic Liquidtight Fittings Straight with Male Metallic Metal Fitting E D Throat Dia. C A B Ref. Trade Size (md**) A Ref. B (12) 1/2 (16) 3/4 (21) 1 (27) 11/4 (35) 11/2 (41) 2 (53) 21/2 (63) 3 (78) 31/2 (91) 4 (103) 1 .43" (36 .3) 1 .43" (36 .3) 1 .56" (39 .6) 1 .68" (42 .7) 2 .03" (51 .6) 2 .21" (56 .1) 2 .28" (57 .9) 3 .56" (90 .4) 3 .81" (96 .8) 3 .81" (96 .8) 3 .81" (96 .8) .59" (15 .0) .59" (15 .0) .59" (15 .0) .66" (16 .8) .63" (16 .8) .63" (16 .8) .69" (17 .5) 1 .06" (26 .9) 1 .06" (26 .9) 1 .06" (26 .9) 1 .06" (26 .9) A/C* C 1 .20" (30 .0) 1 .34" (34 .0) 1 .55" (39 .0) 1 .95" (50 .0) 2 .39" (61 .0) 2 .72" (69 .0) 3 .08" (78 .0) 3 .92" (100 .0) 4 .70" (119 .0) 5 .29" (134 .0) 5 .75" (146 .0) A/F* D Throat Dia. A/C* E 1 .06" (26 .9) 1 .19" (30 .2) 1 .37" (34 .8) 1 .69" (42 .9) 2 .06" (52 .3) 2 .38" (60 .5) 2 .87" (72 .9) 3 .62" (91 .9) 4 .31" (109 .5) 4 .81" (122 .2) 5 .31" (134 .9) .61" (15 .5) .61" (15 .5) .84" (21 .3) 1 .06" (26 .9) 1 .37" (34 .8) 1 .53" (38 .9) 2 .06" (52 .3) 2 .42" (61 .5) 3 .01" (76 .5) 3 .49" (88 .6) 3 .96" (100 .6) 1 .07" (27 .2) 1 .22" (31 .0) 1 .43" (36 .3) 1 .73" (43 .9) 2 .36" (59 .9) 2 .79" (70 .9) 3 .32" (84 .3) 3 .85" (97 .8) 4 .65" (118 .1) 5 .18" (131 .6) 5 .75" (146 .1) A/F* E Throat Dia. A/C* 1 .06" (26 .9) 1 .19" (30 .2) 1 .45" (36 .8) 1 .69" (42 .9) 2 .06" (52 .3) 2 .38" (60 .5) 2 .88" (73 .2) .60" (15 .2) .61" (15 .2) .84" (21 .3) 1 .05" (26 .7) 1 .37" (34 .8) 1 .60" (40 .6) 2 .05" (52 .1) 1 .16" (29 .5) 1 .21" (30 .7) 1 .50" (38 .1) 1 .82" (46 .2) 2 .32" (58 .9) 2 .62" (66 .5) 3 .21" (81 .5) A/F* D Ref. E Throat Dia. A/C* 1 .06" (26 .9) 1 .12" (28 .4) 1 .45" (36 .8) 1 .60" (40 .6) 2 .06" (52 .3) 2 .38" (60 .5) 2 .87" (72 .9) 3 .63" (92 .2) 4 .31" (109 .5) 5 .31" (134 .9) 1 .44" (36 .6) 1 .44" (36 .6) 1 .63" (41 .4) 2 .19" (55 .6) 2 .50" (63 .5) 2 .69" (68 .3) 3 .25" (82 .6) 4 .25" (108 .0) 4 .87" (123 .7) 5 .63" (143 .0) .60" (15 .2) .61" (15 .5) .83" (21 .1) 1 .05" (26 .7) 1 .36" (34 .5) 1 .61" (40 .9) 2 .05" (52 .1) 2 .42" (61 .5) 3 .01" (76 .5) 3 .96" (100 .6) 1 .13" (29 .0) 1 .12" (28 .0) 1 .48" (38 .0) 1 .80" (46 .0) 2 .32" (59 .0) 2 .58" (66 .0) 3 .14" (80 .0) 3 .78" (96 .0) 4 .64" (118 .0) 5 .76" (146 .0) A/F* .93" (23 .6) 1 .06" (26 .9) 1 .25" (31 .8) 1 .56" (39 .6) 2 .08" (52 .8) 2 .48" (63 .0) 2 .90" (73 .7) 3 .60" (91 .4) 4 .33" (110 .0) 4 .82" (122 .4) 5 .39" (136 .9) 45 with Male Metallic Metal Fitting B A D F C E Throat Dia. Trade Size (md**) A B C (12) 1/2 (16) 3/4 (21) 1 (27) 11/4 (35) 11/2 (41) 2 (53) 1 .19" (30 .2) 1 .19" (30 .2) 1 .19" (30 .2) 1 .38" (35 .1) 1 .42" (36 .1) 1 .66" (42 .2) 1 .69" (42 .9) 1 .28" (32 .5) 1 .28" (32 .5) 1 .43" (36 .3) 1 .53" (38 .9) 1 .69" (42 .9) 2 .00" (50 .8) 2 .25" (57 .2) .59" (15 .0) .59" (15 .0) .59" (15 .0) .66" (16 .8) .63" (16 .0) .66" (16 .8) .66" (16 .8) A/C* D 1 .20" (30 .5) 1 .34" (34 .0) 1 .55" (39 .4) 1 .95" (49 .5) 2 .39" (60 .7) 2 .72" (69 .1) 3 .08" (78 .2) F A/F* 1 .02" (25 .9) 1 .06" (26 .9) 1 .32" (33 .5) 1 .59" (40 .4) 2 .03" (5 .16) 2 .29" (58 .2) 2 .80" (71 .1) 90 with Male Metallic Metal Fitting F Technical Information C D B A E Throat Dia. Trade Size (md**) A B (12) 1/2 (16) 3/4 (21) 1 (27) 11/4 (35) 11/2 (41) 2" (53) 21/2 (63) 3 (78) 4 (103) 1 .31" (33 .3) 1 .31" (33 .3) 1 .44" (36 .6) 1 .78" (45 .2) 1 .97" (50 .0) 2 .19" (55 .6) 2 .53" (64 .3) 3 .44" (87 .4) 3 .75" (95 .3) 4 .25" (108 .0) .59" (15 .0) .59" (15 .0) .59" (15 .0) .59" (15 .0) .63" (16 .0) .63" (16 .0) .66" (16 .8) 1 .00" (25 .4) 1 .00" (25 .4) 1 .00" (25 .4) A/C* C 1 .20" (30 .5) 1 .34" (34 .0) 1 .55" (39 .4) 1 .95" (49 .5) 2 .39" (60 .7) 2 .72" (69 .1) 3 .08" (78 .2) 3 .92" (99 .6) 4 .70" (119 .4) 5 .75" (146 .1) F A/F* .99" (25 .1) 1 .00" (25 .4) 1 .29" (32 .8) 1 .57" (39 .9) 2 .02" (51 .3) 2 .25" (57 .2) 2 .75" (69 .9) 3 .50" (88 .9) 4 .30" (109 .2) 5 .38" (136 .7) Note: * A/C = Across Corners A/F = Across Flats. ** md = metric designator. T-114 www.hubbell-wiring.com Dimensions in Inches (cm)