Kellems® Wire Management Products Index
Section T
Kellems® Wire Management Products
Wire Management Products
Index
T-1
www.hubbell-wiring.com
Pulling Grips
Strain Relief Grips
Support Grips
Cord Connectors
Index
Product Page
Kellems® Wire Mesh Grips Diagram ....................................T-2
Quick Reference Selection Guide for Grip Applications. . . . . . . . . . . . . . . . . . . .T-4
Pulling Grips ........................................................T-5
Overhead DUA-PULL® Pulling Grips ...................................T-6
Overhead Multiple Strength Pulling Grips ...............................T-7
Underground K-Type Pulling Grips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T- 8
Underground T-Type Pulling Grips .....................................T- 9
Special Purpose Pulling Grips .......................................T-10
Low Tension Pulling Grips ..........................................T-12
Wire Rope Splicing Grips ...........................................T-13
Cable Splicing Grips ...............................................T-14
Tools and Bands ..................................................T-15
Swivels ..........................................................T-16
Technical Information ..............................................T-17
Support Grips ......................................................T-28
Standard Duty Support Grips ........................................T-30
Heavy Support Grips ..............................................T-34
Service Drop Grips ................................................T-36
Bus Drop Support Grips ............................................T-38
Conduit Riser Grips ................................................T-39
Support Grips Technical Information ..................................T-42
Conduit Riser Grips Technical Information .............................T-47
Fiber Optic Cable Grips ..............................................T-49
Pulling Grips .....................................................T-50
Support Grips ....................................................T-53
Technical Information ..............................................T-54
Hose Containment Grips .............................................T-58
Strain Relief Grips for Flexible Cords ..................................T-59
Deluxe Cord Grips .................................................T-60
PG and Metric Threaded Deluxe Cord Grips ............................T-64
Dust-Tight Strain Relief Grips ........................................T-65
I-Grips ..........................................................T-66
Adapters for Multi-Pin Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-67
Strain Relief Grips for Liquidtight Conduit ..............................T-68
Technical Information ..............................................T-71
Cord Connectors ...................................................T-81
Straight Male Cord Connectors ......................................T-82
45° Male Cord Connectors ..........................................T-85
90° Male Cord Connectors ..........................................T-86
Straight Female and Underground Feeder .............................T-87
Low Profile N.P.T., PG and Metric Thread Connectors ....................T-88
Accessories ......................................................T-89
Hubbell Juniors® Miniature Nylon Cord Connectors ......................T-90
Cord Connectors Technical Information ...............................T-92
Hubbell Juniors® Technical Information ...............................T-102
PolyTuff® Non-Metallic Liquidtight Conduit and Tubing ..................T-104
PolyTuff® Non-Metallic Liquidtight Fittings. . . . . . . . . . . . . . . . . . . . . . . . . . . . .T-106
Metallic Liquidtight Conduit Fittings ..................................T-108
Technical Information .............................................T-110
Support Grip
Conduit
Support Grip
Overhead
Pulling Grip
Bus Drop
Support Grip
Support Grip
Conduit Support
Underground
Pulling Grip
Flexible
Conduit
Grip
Strain
Relief
Grip
Deluxe
Cord Grip
Support Grip
Bus Drop
Support Grip
Flexible
Conduit Grip
Bus Drop
Support Grip Deluxe Cord Grip
Strain Relief GripHose Containment Grip
Underground
Pulling Grip
INDUSTRY
INDUSTRY
UTILITY
UTILITY
COMMERCIAL RESIDENTIAL
Support Grip
To help you fully visualize the variety of uses available to you through Hubbell-Kellems
Mesh Grips, we have prepared this diagram of common applications. It follows the
typical pattern of usage you would find traveling from utility to industrial, commercial
and residential environments.
Pulling Grips are instrumental in the installations of transmission lines, service lines
and cabling for construction and maintenance.
Support Grips provide holding management for indoor and outdoor permanent
cable installations.
Strain Relief Grips are most often used to provide maximum reliability and minimum
maintenance in areas where cords on machinery or equipment is impacted by motion
or vibration or at risk of damage from cable pullout.
Beyond the electrical applications illustrated here, Hubbell-Kellems Mesh Grips can
be used for wire management on radio and microwave communications towers,
crane and hoist wire rope maintenance, elevator cable management and more.
T-2 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems® Wire Mesh Grips Diagram Kellems® Wire Management Products
Wire Management Products
Kellems® Wire Mesh Grips Diagram
Support Grip
Conduit
Support Grip
Overhead
Pulling Grip
Bus Drop
Support Grip
Support Grip
Conduit Support
Underground
Pulling Grip
Flexible
Conduit
Grip
Strain
Relief
Grip
Deluxe
Cord Grip
Support Grip
Bus Drop
Support Grip
Flexible
Conduit Grip
Bus Drop
Support Grip Deluxe Cord Grip
Strain Relief GripHose Containment Grip
Underground
Pulling Grip
INDUSTRY
INDUSTRY
UTILITY
UTILITY
COMMERCIAL RESIDENTIAL
Support Grip
T-3
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Kellems® Wire Mesh Grips Diagram
T-4 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems® Wire Management Products
Quick Reference Selection Guide for Grip Applications
Quick Reference Selection Guide for Grip Applications Kellems® Wire Management Products
Universal Eye
Used to fasten
around a
structure or
closed loop.
Available on
standard duty
support and light
or heavy duty
service drop
grips. See pages
T-33 and T-37.
Single Eye
For single hook
attachment
of permanent
indoor/outdoor
cable. Available
on heavy-duty,
standard duty,
and service drop
grips. See pages
T-30, T-34, and
T-36.
Heavy-Duty
Rotating Eye
For underground
wiring and over-
head heavy-duty
pulling of service
lines and new
construction cable.
See pages T-7
and T-8.
Deluxe Cord
Indoor or outdoor
use where subject
to moisture, splash,
or washdown.
Examples are
enclosures, crane
hoist and pendant
drop stations,
hand tools, pumps,
and processing
equipment. Available
in straight, 90°, or
45° configurations.
See pages T-60 to
T-64.
Single Offset Eye
For offset hook
attachment of
permanent indoor/
outdoor cable.
Available on
standard duty and
light-duty support
grips. See page
T-32.
Light-Duty
Flexible Eye
For light industrial
pulling of electri-
cal cable and for
underground and
industrial plant
wiring and
re-wiring. See
page T-12.
Dust-Tight
Strain Relief
Indoor use only for
wiring of electrical
enclosures,
machine tools,
portable power
tools, bus drop
cable systems.
See page T-65.
Double Eye
For double hook
attachment of
permanent indoor/
outdoor cable.
Available on
heavy-duty and
standard duty
grips. See pages
T-31 and T-35.
Heavy-Duty
Flexible Eye
For overhead
transmission and
distribution line
stringing. See
pages T-6, T-7,
and T-9.
Liquid-Tight, Flexible
Metal Conduit
Wiring of machine
tools, electrical
enclosures, motors,
and systems
subjected to vibration,
flexure, motion, or
strain. Available in
straight, 90°, or 45°
configurations. See
pages T-68 to T-70.
Slack Grips
For removing
underground
cable and pulling
slack in existing
cable and new
installations and
when end of cable
is not available.
See pages T-10
and T-11.
Splicing Grips
Used as temporary splice for cable and wire rope, or as
reinforcement to protect cables and hoses. See pages
T-13 and T-14.
Conduit Riser Grips
Ideal for supporting electrical wires inside rigid conduit via
a supporting ring. See pages T-39 to T-41.
Hose Containment Grips
Used on flexible hose lines to prevent violent whipping of
hose in the event of failure at the fitting. See page T-58.
Specifications are subject to change without notice.
Support Grips Strain Relief Grips
Support Grips
Pulling Grips
Other Specialty Grips
Wide Range
Bus Drop
Used indoors for
cable support
where flexible
cable connects
electrical
equipment to bus
duct. Support air
hose and water
hose. See page
T-38.
T-5
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products
Pulling Grips
Overhead, Underground, Commercial Construction, Specialty
Kellems® Wire Management Products Pulling Grips
Flexible or rotating eyes will mate easily with line stringing swivels
for attachment to pulling lines; they have great strength for
trouble free pulling jobs
Shoulder protectors contain the cable inside the grip and smooth
the passage of the grip over line stringing blocks or conduit bends;
they protect the leading edge of the grip from abrasion
The galvanized steel mesh grip provides strength for secure pulling
jobs and a slim profile with little build-up; it has flexibility to follow
cable path
The multiweave styles available add strength for big pulling jobs
and provide positive gripping power
Endless weave allows easy installation onto cable. It has a snag-free
low profile; designed to be a reusable tool
T-6 Dimensions in Inches (cm)
www.hubbell-wiring.com
DUA-PULL® Grips
Diameter Range Approx. Diameter
Conductor Rope* Breaking Eye B Over Cable
Diameter Diameter Strength E M Diameter & Grip** Color Catalog
Inches (cm) Inches (cm) Lbs. (N) In. (cm) In. (cm) In. (cm) In. (cm) Code Number
.19"-.37" (.48-.94) .25"-.65" (.63-1.65) 6,500 (28,912) 10" (25.40) 24" (60.96) .220" (.56) .200" (.51) Black 033271037
.38"-.62" (.97-1.57) .50"-.90" (1.27-2.29) 14,000 (62,272) 12" (30.48) 36" (91.44) .375" (.95) .280" (.71) Dk Green 033271038
.63"-.87" (1.60-2.21) .75"-1.10" (1.90-2.79) 20,000 (88,960) 13" (33.02) 48" (121.92) .437" (1.11) .360" (.91) Red 033271039
.88"-1.12" (2.24-2.84) 1.00"-1.50" (2.54-3.81) 30,600 (136,109) 15" (38.10) 60" (152.40) .500" (1.27) .500" (1.27) Dk Blue 033271040
1.13"-1.37" (2.87-3.48) 1.25"-1.70" (3.17-4.32) 46,800 (208,166) 18" (45.72) 76" (193.04) .625" (1.59) .625" (1.59) Yellow 033271041
1.38"-1.90" (3.51-4.38) 1.50"-2.10" (3.81-5.33) 66,500 (295,792) 24" (60.96) 89" (226.06) .750" (1.90) .750" (1.90) Alum. 033271042
Note: E- Eye length.
M-Mesh length at nominal diameter.
* For rope, select smallest size grip which meets required work load.
** Add to cable or rope diameter.
DUA-PULL® Feed Tube
For Use with Rope Diameter Feed Tube Length Catalog
DUA- PULL Grip Inches (cm) Inches (cm) Number
033271037 .25"-.65" (.63-1.65) 28" (71.12) 091061043
033271038 .50"-.90" (1.27-2.29) 40" (101.60) 091061044
033271039 .75"-1.10" (1.90-2.79) 52" (132.08) 091061045
033271040 1.00"-1.50" (2.54-3.81) 67" (170.18) 091061046
033271041 1.25"-1.70" (3.17-4.32) 83" (210.82) 091061047
033271042 1.50"-2.10" (3.81-5.33) 96" (243.84) 091061048
DUA-PULL® Grips
DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for
overhead transmission line stringing applications. They have a dual function, not
provided by any other grip, of working with both bare and insulated conductors
and synthetic rope.
Kellems® Wire Management Products
Overhead DUA-PULL® Pulling Grips
Flexible Eye, Double Weave Mesh, Galvanized Steel
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Overhead DUA-PULL® Pulling Grips Kellems® Wire Management Products
T-7
Dimensions in Inches (cm) www.hubbell-wiring.com
Multiple Strength Grip-Rotating Eye
Cable Diameter Approx. Breaking E M Rotating Eye Color Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Dia. Inches (cm) Code Number
.25"-.49" (.63-1.24) 6,800 (20,567) 5" (12.70) 26" (66.04) ⁷⁄₈" (2.22) Dark Green 03302016
.50"-.74" (1.27-1.88) 10,000 (44,480) 6" (15.24) 32" (81.28) 1" (2.54) Brown 03302018
.75"-.99" (1.90-2.51) 14,400 (64,051) 6" (15.24) 41" (104.14) 1" (2.54) Light Blue 03302020
1.00"-1.24" (2.54-3.15) 24,600 (109,420) 8" (20.32) 52" (132.08) 1³⁄₈" (3.49) Gold 03302022
1.25"-1.49" (3.17-3.78) 30,600 (136,109) 8" (20.32) 56" (142.24) 1⁵⁄₈" (4.13) Black 03302024
1.50"-1.74" (3.81-4.42) 30,600 (136,109) 9" (22.86) 60" (152.40) 1⁷⁄₈" (4.76) Red 03302026
1.75"-2.24" (4.44-5.69) 48,000 (213,504) 10" (25.40) 70" (177.80) 1⁷⁄₈" (4.76) Dark Blue 03302028
2.00"-2.49" (5.08-6.32) 48,000 (213,504) 10" (25.40) 50" (127.00) 1⁷⁄₈" (4.76) Yellow 03302066
2.50"-2.99" (6.35-7.59) 48,000 (213,504) 10" (25.40) 52" (132.08) 1⁷⁄₈" (4.76) Orange 03302097
3.00"-3.49" (7.62-8.86) 48,000 (213,504) 10" (25.40) 54" (137.16) 1⁷⁄₈" (4.76) Aluminum 033021030
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 10" (25.40) 58" (142.24) 1⁷⁄₈" (4.76) Light Green 033021031
Note: E- Eye length.
M-Mesh length at nominal diameter.
Multiple Strength Grip-Flexible Eye
Cable Diameter Approx. Breaking E M A-Eye Color Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Dia. Inches (cm) Code Number
.25"-.49" (.63-1.24) 6,800 (20,567) 9" (22.86) 26" (66.04) ¹⁄₄" (.63) Dark Green 03302044
.50"-.74" (1.27-1.88) 10,000 (44,480) 9" (22.86) 32" (81.28) ⁵⁄₁₆" (.79) Brown 03302046
.75"-.99" (1.90-2.51) 14,400 (64,051) 11" (27.94) 41" (104.14) ³⁄₈" (.95) Light Blue 03302048
1.00"-1.24" (2.54-3.15) 24,600 (109,420) 12" (30.48) 52" (132.08) ¹₂" (1.27) Gold 03302050
1.25"-1.49" (3.17-3.78) 30,600 (136,109) 12" (30.48) 56" (142.24) ¹₂" (1.27) Black 03302052
1.50"-1.74" (3.81-4.42) 30,600 (136,109) 12" (30.48) 60" (152.40) ¹₂" (1.27) Red 03302054
1.75"-2.24" (4.44-5.69) 48,000 (213,504) 18" (45.72) 70" (177.80) ⁵⁄₈" (1.59) Dark Blue 03302056
2.00"-2.49" (5.08-6.32) 48,000 (213,504) 18" (45.72) 50" (127.00) ⁵⁄₈" (1.59) Yellow 033021078
2.50"-2.99" (6.35-7.59) 48,000 (213,504) 18" (45.72) 52" (132.08) ⁵⁄₈" (1.59) Orange 033021079
3.00"-3.49" (7.62-8.86) 48,000 (213,504) 18" (45.72) 54" (137.16) ⁵⁄₈" (1.59) Aluminum 033021080
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 18" (45.72) 58" (142.24) ⁵⁄₈" (1.59) Light Green 033021081
Note: E- Eye length.
M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Overhead Multiple Strength Pulling Grips
Flexible or Rotating Eye, Triple, Double, Single Weave, Galvanized Steel
Multiple Strength Style Grips
Multiple Strength Pulling Grips are designed for pulling aluminum or
copper bare conductor, ground wires, messenger strands, wire rope
and insulated cables.
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Kellems® Wire Management Products Overhead Multiple Strength Pulling Grips
T-8 Dimensions in Inches (cm)
www.hubbell-wiring.com
K-Type Grips
Rotating Eye
Cable Diameter Approx. Breaking E M Diameter
Range Inches (cm) Strength Lbs. (N) In. (cm) In. (cm) Inches (cm) Catalog Number
Short
.50"-.62" (1.27-1.57) 5,600 (24,909) 5" (12.70) 11" (27.94) ⁷⁄₈" (2.22) 03301001
.63"-.74" (1.60-1.88) 6,800 (30,246) 5" (12.70) 11" (27.94) ⁷⁄₈" (2.22) 03301002
.75"-.99" (1.90-2.51) 6,800 (30,246) 6" (15.24) 20" (50.80) 1" (2.54) 03301013
1.00"-1.24" (2.54-3.15) 12,800 (56,934) 7" (17.78) 20" (50.80) 1³⁄₈" (3.49) 03301014
1.25"-1.49" (3.17-3.78) 12,800 (56,934) 7" (17.78) 21" (53.34) 1³⁄₈" (3.49) 03301016
1.50"-1.99" (3.81-5.05) 16,400 (72,941) 7" (17.78) 25" (63.50) 1³⁄₈" (3.49) 03301017
2.00"-2.49" (5.08-6.32) 27,200 (120,986) 8" (20.32) 26" (66.04) 1⁵⁄₈" (4.13) 03301018
2.50"-2.99" (6.35-7.59) 33,000 (146,784) 10" (25.40) 28" (71.12) 1⁷⁄₈" (4.76) 03301019
3.00"-3.49" (7.62-8.86) 41,000 (182,368) 10" (25.40) 30" (76.20) 1⁷⁄₈" (4.76) 03301020
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 10" (25.40) 32" (81.28) 1⁷⁄₈" (4.76) 03301021
4.00"-4.49" (10.16-11.40) 48,000 (213,504) 10" (25.40) 33" (83.82) 1⁷⁄₈" (4.76) 033011017
Standard
.50"-.62" (1.27-1.57) 5,600 (24,909) 5" (12.70) 16" (40.64) ⁷⁄₈" (2.22) 03301011
.63"-.74" (1.60-1.88) 6,800 (30,246) 5" (12.70) 16" (40.64) ⁷⁄₈" (2.22) 03301012
.75"-.99" (1.90-2.51) 9,600 (42,701) 6" (15.24) 32" (81.28) 1" (2.54) 03301024
1.00"-1.49" (2.54-3.78) 16,400 (72,947) 7" (17.78) 33" (83.82) 1³⁄₈" (3.49) 03301025
1.50"-1.99" (3.81-5.05) 16,400 (72,947) 7" (17.78) 34" (86.36) 1³⁄₈" (3.49) 03301026
2.00"-2.49" (5.08-6.32) 27,200 (120,986) 9" (22.86) 36" (91.44) 1⁵⁄₈" (4.13) 03301027
2.50"-2.99" (6.35-7.59) 33,000 (146,784) 10" (25.40) 38" (96.52) 1⁷⁄₈" (4.76) 03301028
3.00"-3.49" (7.62-8.86) 41,000 (182,368) 10" (25.40) 39" (99.06) 1⁷⁄₈" (4.76) 03301029
3.50"-3.99" (8.89-10.13) 48,000 (213,504) 10" (25.40) 41" (104.14) 1⁷⁄₈" (4.76) 03301030
4.00"-4.49" (10.16-11.40) 48,000 (213,504) 10" (25.40) 42" (106.68) 1⁷⁄₈" (4.76) 03301031
4.50"-4.99" (11.43-12.67) 48,000 (213,504) 10" (25.40) 58" (147.32) 1⁷⁄₈" (4.76) 03301039
5.00"-5.99" (12.70-15.21) 40,000 (177,920) 10" (25.40) 60" (152.40) 1⁷⁄₈" (4.76) 03301047
6.00"-6.99" (15.24-17.75) 54,000 (240,192) 10" (25.40) 66" (167.64) 1⁷⁄₈" (4.76) 03301045
Note: E- Eye length.
M-Mesh length at nominal diameter.
See page T-26 for multiple cables in a single pulling grip.
Kellems® Wire Management Products
Underground K-Type Pulling Grips
Rotating Eye, Double Weave, Galvanized Steel
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Underground K-Type Pulling Grips Kellems® Wire Management Products
K-Type Grips
Kellems® Rotating Eye, K-Type Pulling Grips are made of high strength
galvanized steel strand. All Grips feature double weave mesh for greater
strength and added mesh contact on the table, to handle longer or heavier
pulling jobs. The forged eye mates easily with a swivel or shackle.
T-9
Dimensions in Inches (cm) www.hubbell-wiring.com
T-Type Grips
Cable Diameter Approx. Breaking E M
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Catalog Number
Short
.50"-.62" (1.27-1.57) 4,500 (20,016) 8" (20.32) 21" (53.34) 033041082
.63"-.74" (1.60-1.88) 5,600 (24,909) 8" (20.32) 24" (60.96) 033041083
.75"-.99" (1.90-2.51) 6,800 (30,246) 9" (22.86) 24" (60.96) 033041084
1.00"-1.49" (2.54-3.78) 9,600 (42,701) 9" (22.86) 24" (60.96) 033041085
1.50"-1.99" (3.81-5.05) 16,400 (72,947) 11" (27.94) 24" (60.96) 033041086
2.00"-2.49" (5.08-6.32) 18,500 (82,288) 12" (30.48) 24" (60.96) 033041087
2.50"-2.99" (6.35-7.59) 24,500 (108,976) 12" (30.48) 24" (60.96) 033041088
3.00"-3.49" (7.62-8.86) 24,500 (108,976) 14" (35.56) 24" (60.96) 033041089
3.50"-3.99" (8.89-10.13) 31,000 (137,888) 14" (35.56) 26" (66.04) 033041090
Standard
.75"-.99" (1.90-2.51) 6,800 (30,246) 9" (22.86) 36" (91.44) 033041091
1.00"-1.49" (2.54-3.78) 9,600 (42,701) 9" (22.86) 36" (91.44) 033041092
1.50"-1.99" (3.81-5.05) 16,400 (72,947) 11" (27.94) 36" (91.44) 033041093
2.00"-2.49" (5.08-6.32) 18,500 (82,288) 12" (30.48) 36" (91.44) 033041094
2.50"-2.99" (6.35-7.59) 24,500 (108,976) 12" (30.48) 36" (91.44) 033041095
3.00"-3.49" (7.62-8.86) 24,500 (108,976) 14" (35.56) 36" (91.44) 033041096
3.50"-3.99" (8.89-10.13) 31,000 (137,888) 14" (35.56) 40" (101.60) 033041097
Note: E- Eye length.
M-Mesh length at nominal diameter.
See page T-26 for multiple cables in a single pulling grip.
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Kellems® Wire Management Products
Underground T-Type Pulling Grips
Flexible Eye, Double Weave, Galvanized Steel
Kellems® Wire Management Products Underground T-Type Pulling Grips
T-Type Grips
Kellems® Flexible T-Type Pulling Grips are made of high strength galvanized
steel strand. They feature double weave mesh for positive holding power in
medium to heavy pulling jobs. The grip eye will easily attach to a swivel.
T-10 Dimensions in Inches (cm)
www.hubbell-wiring.com
Non-Conductive Grips, Single Eye, Double Weave, Non-Metallic
Approx.
Breaking
Cable Diameter Strength E M A Color Catalog
Range Inches (cm) Lbs. (N) In. (cm) In. (cm) In. (cm) Code Number
.50"-.62" (1.27-1.57) 4,000 (17,792) 5.5" (13.97) 24" (60.96) .44" (1.12) Green 03628001
.63"-.74" (1.60-1.88) 5,000 (22,240) 5.5" (13.97) 26" (66.04) .44" (1.12) Yellow 03628002
.75"-.99" (1.90-2.51) 6,000 (26,688) 6.0" (15.24) 31" (78.74) .63" (1.60) Red 03628003
1.00"-1.24" (2.54-3.15) 6,000 (26,688) 6.5" (16.51) 36" (91.44) .63" (1.60) Blue 03628004
1.25"-1.49" (3.17-3.78) 6,000 (26,688) 6.7" (17.02) 41.5" (105.41) .63" (1.60) White 03628005
1.50"-1.99" (3.815.05) 6,000 (26,688) 8.0" (20.32) 44.0" (121.76) .63" (1.60) Pink 03628006
Slack Grip-Closed Mesh,
Offset Eye, Double Weave, Galvanized Steel
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
Standard
.75"-.99" (1.90-2.51) 2,600 (11,565) 7" (17.78) 12" (30.48) 03308003
1.00"-1.24" (2.54-3.15) 4,000 (17,792) 8" (20.32) 15" (38.10) 03308004
1.25"-1.49" (3.17-3.78) 5,400 (24,019) 8" (20.32) 16" (40.64) 03308005
1.50"-1.74" (3.81-4.42) 6,600 (29,357) 8" (20.32) 20" (50.80) 03308006
1.75"-1.99" (4.44-5.05) 10,000 (44,480) 10" (25.40) 18" (45.72) 03308007
2.00"-2.49" (5.08-6.32) 11,000 (48,928) 10" (25.40) 19" (48.26) 03308008
2.50"-2.99" (6.35-7.59) 11,000 (48,928) 10" (25.40) 20" (50.80) 03308009
3.00"-3.49" (7.62-8.86) 14,500 (64,496) 12" (30.48) 21" (53.34) 03308010
3.50"-3.99" (8.89-10.13) 14,500 (64,496) 12" (30.48) 22" (55.88) 03308011
Note: E- Eye length.
M-Mesh length at nominal diameter.
See page T-26 for multiple cables in a single pulling grip.
Kellems® Wire Management Products
Special Purpose Pulling Grips
Non-Conductive and Slack Pulling
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Kellems® Non-Conductive
Pulling Grips, made of a high
strength, non-conductive
aramid fiber, are available for
pulling single cable or cable
bundles. Their braided double
weave design adds strength
and positive holding power.
Slack Pulling Grips are offered
in three styles made of
galvanized steel. The closed
type is used when the cable
end is accessible. When not
accessible, there are split lace
and split rod closing styles.
All grips feature a single offset
eye for easy attachment to a
pulling line.
Special Purpose Pulling Grips Kellems® Wire Management Products
T-11
Dimensions in Inches (cm) www.hubbell-wiring.com
Slack Grip-Split Mesh, Rawhide Lace Closing,
Offset Eye, Double Weave, Galvanized Steel
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
Standard
.75"-.99" (1.90-2.51) 2,500 (11,120) 7" (17.78) 12" (30.48) 03309003
1.00"-1.24" (2.54-3.15) 3,500 (15,568) 8" (20.32) 15" (38.10) 03309004
1.25"-1.49" (3.17-3.78) 4,000 (17,792) 8" (20.32) 16" (40.64) 03309005
1.50"-1.74" (3.81-4.42) 4,000 (17,792) 9" (22.86) 17" (43.18) 03309006
1.75"-1.99" (4.44-5.05) 4,000 (17,792) 10" (25.40) 18" (45.72) 03309007
2.00"-2.49" (5.08-6.32) 4,000 (17,792) 10" (25.40) 19" (48.26) 03309008
2.50"-2.99" (6.35-7.59) 4,000 (17,792) 10" (25.40) 20" (50.80) 03309009
Long
1.50"-1.99" (3.81-5.05) 4,000 (17,792) 9" (22.86) 25" (63.50) 03309015
2.00"-2.49" (5.08-6.32) 4,000 (17,792) 10" (25.40) 26" (66.04) 03309016
2.50"-2.99" (6.35-7.59) 4,000 (17,792) 10" (25.40) 29" (73.66) 03309017
3.00"-3.49" (7.62-8.86) 4,000 (17,792) 12" (30.48) 32" (81.28) 03309018
3.50"-3.99" (8.89-10.13) 4,000 (17,792) 12" (30.48) 35" (88.90) 03309019
Slack Grip-Split Mesh, Rod Closing,
Offset Eye, Single Weave, Galvanized Steel
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.61" (1.27-1.55) 1,500 (6,672) 7" (17.78) 6" (15.24) 03310001
.62"-.74" (1.57-1.88) 1,800 (8,006) 7" (17.78) 8" (20.32) 03310002
.75"-.99" (1.90-2.51) 2,200 (9,786) 7" (17.78) 10" (25.40) 03310003
1.00"-1.24" (2.54-3.15) 3,400 (15,123) 8" (20.32) 12" (30.48) 03310004
1.25"-1.49" (3.17-3.78) 4,500 (20,016) 8" (20.32) 14" (35.56) 03310005
1.50"-1.74" (3.81-4.42) 5,800 (25,798) 9" (22.86) 15" (38.10) 03310006
1.75" -1.99" (4.44-5.05) 7,600 (33,805) 10" (25.40) 16" (40.64) 03310007
2.00"-2.49" (5.08-6.32) 9,000 (40,032) 10" (25.40) 19" (48.26) 03310008
2.50"-2.99" (6.35-7.59) 11,000 (48,928) 10" (25.40) 20" (50.80) 03310009
3.00"-3.49" (7.62-8.86) 12,000 (53,376) 12" (30.48) 21" (53.34) 03310010
3.50"-3.99" (8.89-10.13) 12,000 (53,376) 12" (30.48) 24" (60.96) 03310011
Note: E- Eye length.
M-Mesh length at nominal diameter.
See page T-26 for multiple cables in a single pulling grip.
Kellems® Wire Management Products
Special Purpose Pulling Grips
Slack Pulling
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Slack Pulling Grips are
offered in three styles made
of galvanized steel. The
closed type is used when
the cable end is accessible.
When not accessible, there
are split lace and split rod
closing styles. All grips
feature single offset eye
for easy attachment to a
pulling line.
Kellems® Wire Management Products Special Purpose Pulling Grips
T-12 Dimensions in Inches (cm)
www.hubbell-wiring.com
Light Duty Grips
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
Short
.50"-.62" (1.27-1.57) 2,800 (12,454) 5" (12.70) 11" (27.94) 03303001
.63"-.74" (1.60-1.88) 2,800 (12,454) 5" (12.70) 11" (27.94) 03303002
.75"-.99" (1.90-2.51) 4,000 (17,792) 6" (15.24) 12" (30.48) 03303003
1.00"-1.24" (2.54-3.15) 5,300 (23,574) 7" (17.78) 13" (33.02) 03303004
1.25"-1.49" (3.17-3.78) 5,300 (23,574) 7" (17.78) 14" (35.56) 03303005
1.50"-1.74" (3.81-4.42) 6,800 (30,246) 8" (20.32) 15" (38.10) 03303006
1.75"-1.99" (4.44-5.05) 8,500 (37,808) 9" (22.86) 17" (43.18) 03303007
2.00"-2.49" (5.08-6.32) 8,500 (37,808) 9" (22.86) 18" (45.72) 03303008
Standard
.50"-.62" (1.27-1.57) 2,800 (12,454) 5" (12.70) 16" (40.64) 03303010
.63"-.74" (1.60-1.88) 2,800 (12,454) 5" (12.70) 16" (40.64) 03303011
.75"-.99" (1.90-2.51) 4,000 (17,792) 6" (15.24) 20" (50.80) 03303012
1.00"-1.24" (2.54-3.15) 6,800 (30,246) 7" (17.78) 20" (50.80) 03303013
1.25"-1.49" (3.17-3.78) 6,800 (30,246) 7" (17.78) 21" (53.34) 03303015
1.50"-1.99" (3.81-5.05) 6,800 (30,246) 8" (20.32) 23" (58.42) 03303016
2.00"-2.49" (5.08-6.32) 8,500 (37,808) 9" (22.86) 25" (63.50) 03303017
2.50"-2.99" (6.35-7.59) 10,600 (47,149) 9" (22.86) 27" (68.58) 03303018
3.00"-3.49" (7.62-8.86) 14,700 (65,386) 10" (25.40) 30" (76.20) 03303019
3.50"-3.99" (8.89-10.13) 14,700 (65,386) 10" (25.40) 32" (81.28) 03303029
Junior Pulling Grips
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Model Number
.19"-.24" (.48-.61) 400 (1,779) 3¹⁄₄" (8.25) 4¹⁄₄" (10.79) J19 03305011*
.25"-.37" (.63-.94) 450 (2,002) 3¹⁄₄" (8.25) 4¹⁄₄" (10.79) J25 03305001
.38"-.49" (.97-1.24) 900 (4,003) 3³⁄₄" (9.52) 7" (17.78) J37 03305002
.50"-.62" (1.27-1.57) 1,300 (5,782) 4¹⁄₄" (10.79) 8¹⁄₂" (21.59) J50 03305003
.63"-.74" (1.60-1.88) 1,950 (8,674) 5" (12.70) 10" (25.40) J62 03305004
.75"-.99" (1.90-2.51) 2,800 (12,454) 5³⁄₄" (14.60) 10" (25.40) J75 03305005
1.00"-1.24" (2.54-3.15) 3,900 (17,347) 6¹⁄₂" (16.51) 11¹⁄₂" (29.21) J100 03305006
Note: E- Eye length.
M-Mesh length at nominal diameter.
* Not included in Junior Grip Kit, 033051114.
Kellems® Wire Management Products
Low Tension Pulling Grips
Flexible Eye, Single Weave, Galvanized Steel
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating to
this product on pages T-17
through T-27.
Light Duty Pulling Grips are
made of galvanized steel in
a single weave construction.
They feature a flexible eye
for easy attachment to a
pulling line.
Junior Pulling Grips feature a
strong galvanized steel, single
weave mesh. A flexible eye
easily attaches to a pulling
line, snake or fish tape.
Junior Grip Kit
Junior Grip Kit contains 6 grips,
one of each size. Catalog number
033051114.
Note: See page T-26 for multiple
cables in a single pulling grip.
See page T-27 for building
wire selection chart.
Low Tension Pulling Grips Kellems® Wire Management Products
T-13
Dimensions in Inches (cm) www.hubbell-wiring.com
Regular Wire Rope Grips
Cable Diameter Approx. Breaking Approx. Length Catalog
Range Inches (cm) Strength Lbs. (N) Of Grip Feet (m) Number
⁹⁄₁₆"- ⁵⁄₈" (1.43-1.59) 7,500 (33,360) 5.75 (1.75) 03316001
³⁄₄"- ⁷⁄₈" (1.90-2.22) 12,500 (55,600) 6.75 (1.90) 03316002
1"-1¹⁄₈" (2.54-2.86) 16,000 (71,168) 7.00 (2.13) 03316003
1¹⁄₄"- 1³⁄₈" (3.17-3.49) 20,000 (88,960) 8.00 (2.44) 03316004
1³⁄₈"- 1¹⁄₂" (3.49-3.81) 20,000 (88,960) 8.00 (2.44) 03316006
Rotating Wire Rope Grips
Cable Diameter Approx. Breaking Approx. Length Barrel Dimensions Catalog
Range Inches (cm) Strength Lbs. (N) Of Grip Feet (m) Lgth. x O.D. In. (cm) Number
⁷⁄₁₆"- ¹⁄₂" (1.11-1.27) 5,000 (22,240) 5.33 (1.63) 3.00" (7.62) x .87" (2.21) 03317001
⁹⁄₁₆"- ⁵⁄₈" (1.43-1.59) 7,500 (33,360) 5.83 (1.78) 4.25" (10.79) x 1.00" (2.54) 03317002
³⁄₄"- ⁷⁄₈" (1.90-2.22) 12,500 (55,600) 6.50 (1.98) 4.25" (10.79) x 1.00" (2.54) 03317003
1"- 1¹⁄₈" (2.54-2.86) 16,000 (71,168) 8.67 (2.64) 5.50" (13.97) x 1.37" (3.48) 03317004
1¹⁄₄"- 1³⁄₈" (3.17-3.49) 20,000 (88,960) 9.00 (2.74) 5.50" (13.97) x 1.37" (3.48) 03317005
1¹⁄₂"- 1³⁄₄" (3.81-4.44) 20,000 (88,960) 11.00 (3.35) 5.50" (13.97) x 1.37" (3.48) 03317006
Kellems® Wire Management Products
Wire Rope Splicing Grips
Triple, Double, Single Weave, Galvanized Steel
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Kellems® Wire Rope Grips
are made of high strength
galvanized steel strand in
a construction of triple,
double and single weave
for superior gripping ability.
They are available with or
without a rotating barrel
which will help eliminate
twist in the old rope from
being transferred to the
new rope.
Kellems® Wire Management Products Wire Rope Splicing Grips
T-14 Dimensions in Inches (cm)
www.hubbell-wiring.com
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Splicing Grip
Splicing Grips are made of
galvanized steel in double weave
mesh construction. They are
available in various lengths and
sizes to suit most applications.
Double Weave Tube
Cable Diameter .37"-.49" .50"-.61" .62"-.74" .75"-.99" 1.00"-1.49"
Range Inches (cm) (.94-1.24) (1.27-1.55) (1.57-1.88) (1.90-2.51) (2.54-3.78)
Approx. Breaking Strength 3,500 3,500 4,400 7,500 10,000
Lbs. (N) (15,568) (15,568) (19,571) (33,360) (44,480)
Mesh Length
Inches (cm) Catalog Number
18" (45.72) 013041330 01304064 01304009 — —
24" (60.96) — 01304011 01304013 01304010 01304015
36" (91.44) — — 013041234 01304054 01304055
48" (121.92) — — — 01304017 01304029
72" (182.88) — — — 01304037 013041333
Junior Splicing Grips,
Single Weave
Junior Splicing Grips are made of
galvanized steel and are designed
for use in very light duty and small
splicing jobs.
Junior Tube
Cable Diameter Approx. Breaking Length @ Nom
Range Inches (cm) Strength Lbs. (N) Diameter Inches (cm) Catalog Number
.18"-.24" (.46-.61) 400 (1,779) 7" (17.78) 01301008
.25"-.36" (.63-.91) 400 (1,779) 8" (20.32) 01301013
Kellems® Wire Management Products
Cable Splicing Grips
Double Weave, Galvanized Steel / Single Weave, Galvanized Steel
Cable Splicing Grips Kellems® Wire Management Products
T-15
Dimensions in Inches (cm) www.hubbell-wiring.com
Punch-Lok® Bands
Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from being tripped or pulled loose.
Also, they assure full gripping action by locking the mesh of the tail in tight contact with the cable or rope.
When the tail of a grip is the leading end, the bands are particularly important to prevent accidental release
caused by tripping on obstructions. A conductor-to-conductor (double-socking) pulling operation is a good
example: where two grips connect two conductors to form a temporary splice. Bands should be applied to
the ends of the grips as illustrated herein. It is also common practice to tape over the banded tail area to
assure smooth passage through the sheaves.The conductor should be installed in the grip up to the elbows
of the aluminum shoulders in order to assure full and complete gripping action.
Punch-Lok Bands
Grip Banding Band Width Band Inside
Range Inches (cm) Inches (cm) Diameter Inches (cm) Model Catalog Number
¹⁄₄"-1¹⁄₈" (.63-2.86) ³⁄₈" (.95) 1³⁄₈" (3.49) 0-311 20320050
1¹⁄₈"-1⁵⁄₈" (2.86-4.13) ³⁄₈" (.95) 2" (5.08) 0-316 20320051
1⁵⁄₈"-2¹⁄₄" (4.13-5.71) ⁵⁄₈" (1.59) 2¹⁄₂" (6.35) 0-10 20320052
2¹⁄₄"-3¹⁄₂" (5.71-8.89) ⁵⁄₈" (1.59) 4" (10.16) 0-16 20320053
3¹⁄₂"-5" (8.89-12.70) ⁵⁄₈" (1.59) 6" (15.24) 0-24 20320054
Accessories
Punch-Lok Tools
Description Catalog Number
P-1000 for use with ⁵⁄₈" width Banding tool. 20320048
P-38 for use with ³⁄₈" and ⁵⁄₈" width Banding tool for tight spaces. 20320047
Note: In all cases two Punch-Lok Bands should be double wrapped approximately one inch to two inches (2.54cm to 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release.
Kellems® Wire Management Products
Tools and Bands
Pulling Grips Accessories
Kellems® Wire Management Products Tools and Bands
Punch-Lok® is a registered trademark of Punch-Lok Inc.
C
B
A
F
E
G
D
20308001A
T-16 Dimensions in Inches (cm)
www.hubbell-wiring.com
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-17 through T-27.
Stainless Steel Swivels
Swivels are essential to the efficiency and safety of any high tension application. They are particularly
important where continuous pulls develop higher and higher torque levels. Torque is intensified by the
pull-resistance of the cable itself and the resistance of the high tension controlling equipment regulating
line sag. Ball bearing swivels release torque and prevent it from reaching dangerous levels that can
damage the cable and obstruct the lines.
Stainless Steel Swivels
Maximum Safe
Working Load Dimensions in Inches (cm) Catalog
Lbs. (N) A B C D E F G Model Number
2,250 (10,000) ⁷⁄₈" (2.22) 2½" (6.35) 3³⁄₈" (8.57) ⁷⁄₁₆" (1.11) ³⁄₈" (0.95) ⁵⁄₁₆" (0.79) ³¹⁄₃₂" (2.46) A-13L 20308001A
5,000 (22,240) 1¼" (3.17) 3¹¹⁄₁₆" (9.37) 4¾" (12.06) 1⁷⁄₃₂" (1.35) 1⁷⁄₃₂" (1.35) ¹³⁄₃₂" (1.03) 1⁹⁄₃₂" (3.25) BB-13L 20308002A
9,000 (40,030) 1½" (3.81) 4¼" (10.79) 5⁵⁄₈" (14.29) ¹¹⁄₁₆" (1.75) 1⁹⁄₃₂" (1.51) ½" (1.27) 1⁹⁄₁₆" (3.97) B-13L 20308003A
10,000 (44,480) 1⁵⁄₈" (4.13) 4½" (11.43) 6" (15.24) ¾" (1.90) ¹¹⁄₁₆" (1.75) ⁵⁄₈" (1.59) 1²³⁄₃₂" (4.36) C-13L 20308004A
30,000 (133,440) 2³⁄₈" (6.03) 7⁵⁄₈" (19.37) 10" (25.40) 1³⁄₁₆" (3.02) 1¹⁄₃₂" (2.62) ⁷⁄₈" (2.22) 2²⁵⁄₃₂" (7.06) D-13L 20308005A
Kellems® Wire Management Products
Swivels
Pulling Grips Accessories
Swivels Kellems® Wire Management Products
T-17
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems Pulling Grips are reusable tools for pulling electrical cable, bare conductor or rope. They are easy and fast to
install, providing the user with a smooth, slim profile that allows for easy passage through ducts, conduit, blocks and
sheaves. Kellems Pulling Grips are made of the highest quality galvanized steel strand which assures the user of a long
lasting grip. There is a Kellems Pulling Grip for every pulling job.
CAUTION: It is very important to comply with all of the following precautions. Failure to do so may result in property
damage, personal injury or death.
1. Pulling grips are to be installed by a qualified individual in accordance with all applicable national
and local safety, electrical and rigging codes.
2. Ensure that the correct grip is selected for your specific needs.
3. Do not use a pulling grip for any application other than pulling cable.
4. Thoroughly examine the grip for damage. Do not use a damaged grip.
5. Ensure that the recommended work load of the grip is suitable for the application. Never use grips
at their approximated rated breaking strength. A safety factor of 5 is recommended for pulling grips.
6. Do not alter grips in any way. For example, do not modify pulling eyes, shoulders, fittings or lugs.
7. Do not attach any type of pulling hardware to any point on the grip other than the pulling eye.
The pulling eye is the only acceptable means of attachment to external hardware.
8. Always apply 2 bands at 1" and 2" respectively, from the tail end of the mesh to guard against
accidental release of the grip. Accidental release can occur if an object contracts and pushes
against the tail end of the mesh, thereby expanding and releasing its hold.
Select The Correct Pulling Grip
Each Kellems Grip is designed to work on a specific range of cable diameters.
Step 1 Refer to the chart below to determine the style of grip best suited for your application.
Step 2 Determine your cable outside diameter.
Step 3 Find the grip size that encompasses your cable diameter.
Step 4 Estimate the tension to be put on the grip, establish the working load you require and compare this
to the listed approximate breaking strength of the grip to insure that the grip will be strong enough.
Refer to page T-18 for safety and working load factors.
Pulling Grip Selection Chart
Grip Style Application Page Number
DUA-PULL®, flexible eye Extra high strength overhead transmission line stringing for bare or
insulated conductor and synthetic rope. T-6
Multiple strength, flexible eye Normal overhead transmission and distribution line stringing for bare or
insulated conductor. T- 7
Multiple strength, rotating eye Normal overhead transmission and distribution line stringing for bare or
insulated conductor. T- 7
K-type grip, rotating eye Underground power cables and communication lines. Service lines into factories. T-8
T-type grip, flexible eye Underground power cables and communication lines. Service lines into factories. T-9
Non-conductive, flexible eye Pull insulated distribution cable into place. T-10
Slack pulling, closed mesh Remove underground cable. For pulling slack in final placement of new cable
when end of cable is available. T-10
Slack pulling, split mesh, Remove underground cable. For pulling slack in final placement of new cable
rawhide lace closing when end of cable is not available. T-11
Slack pulling, split mesh, Remove underground cable. For pulling slack in final placement of new cable
rod closing when end of cable is not available, with rod closing for quick installation. T-11
Light duty, flexible eye Light pulling, underground electrical construction. Industrial plant
wiring and rewiring jobs. T-12
Junior, flexible eye Connect bundled insulated building wire to a pulling tape. Pull wire through conduit. T-12
Regular and rotating wire rope Restring wire rope in cranes and oil rigs. T-13
Splicing Temporary splice for cable or wire rope. T-14
Pulling Grip Accessories Tools, bands, swivels. T-15, T-16
Fiber Optic Cable Pulling Grips Pull fiber optic cable into place overhead, underground or through duct and conduit. T-50, T-51, T-52
Kellems® Wire Management Products
Technical Information
Pulling Grips
Kellems® Wire Management Products Technical Information
T-18 Dimensions in Inches (cm)
www.hubbell-wiring.com
The broad application of Kellems grips on a wide
variety of objects requires that adequate safety
factors be used to establish working loads. The
approximate breaking strength of a Kellems grip
represents an average calculation based on data
established from actual direct tension testing done
in our engineering laboratories.
It is impossible to catalog or guarantee a safety
factor suitable for all applications as operating
conditions are never the same. The tension,
diameter, movement, number of objects gripped,
gripping surface, and the attachments used are just
some of the factors which vary with each application.
These factors, together with the effects of abrasion,
corrosion, prior use or abuse and any other variables
of a specific application, must be considered by the
user and the grip replaced as appropriate. Where the
conditions of the application are not well defined or
known, or where risk of injury to persons or property
is involved, a greater safety factor should be utilized.
Under normal conditions, Kellems’ recommended
factor of safety is five for catalog listed pulling
grips, and ten for catalog listed support grips.
Any warranty as to quality, performance or fitness for
use of grips is always premised on the condition that
the published breaking strengths apply only to new,
unused grips, and that such products are properly
stored, handled, used, maintained and inspected by
the user at a frequency appropriate for the use and
condition of the grip.
Examples
Approx. Breaking Safety Max. Rec.
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Catalog Number
Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027
Support Grips 1,610 (7,161) 10 161 (716) 02201018
The maximum recommended working load then is the tension to be exerted on the grip in application with a
margin of safety to take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable for the application.
The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to
the metric unit of weight (kilograms) the conversion factor is 9.808 newtons/kilogram.
Pulling Grip Materials
Material Features Product Group
Galvanized steel wire • High strength • Pulling grips
• Not subject to continuous • Wire rope grips
outside environment • Splicing grips
Non-metallic strand • Superior flex life • Non-conductive pulling grips
• Non-conductive
• Corrosion resistant
• Moderate strength
Approvals
UL and CSA Certification is indicated on appropriate product catalog pages.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Safety And Working Load Factors For Wire Mesh Grips
Technical Information Kellems® Wire Management Products
T-19
Dimensions in Inches (cm) www.hubbell-wiring.com
Overhead Pulling DUA-PULL® Grips
DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for overhead transmission
line stringing applications. They have a dual function of working with both bare and insulated conductors
and synthetic rope, not provided by any other grip. Kellems’ patented two-over, two-under weave design
gives exceptional strength and gripping ability by putting more steel mesh in contact with the cable or
rope surfaces.
THIS IS THE ONLY PULLING GRIP RECOMMENDED FOR USE ON SYNTHETIC ROPE.
Application
The DUA-PULL Grips are primarily used in overhead transmission line construction where loads and safety
considerations require an extra high strength grip. They are most commonly used for attaching pulling lines
to conductors, conductors to running boards and “double socking" for conductor-to-conductor connections.
The DUA-PULL line accommodates ACSR, ACAR, all aluminum and copper conductors. Also, the grips
accommodate ground wires, messenger strands, wire ropes and synthetic ropes.
Benefits
• Made of high strength galvanized steel strand.
• Recommended for pulling bare or insulated conductor, wire rope and synthetic rope.
• DUA-PULL mesh design offers the greatest holding power for all pulling applications.
• Each grip size is color coded for fast and accurate identification and selection.
• Will mate with swivels. See page T-16.
Feed Tubes
The Kellems Feed Tube is used when assembling synthetic rope into the DUA-PULL Grip. It is required on
the largest two sizes of DUA-PULL Grips. Feed Tubes are available for use on all size DUA-PULL Grips.
Benefits
• Saves time, allowing fast, easy assembly.
• Can be reused if not damaged.
Note: 1. Do not run grips or swivels over bullwheels while under tension.
2. Two Punch-Lok® bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release. See page T-15.
3. Double braided rope, such as 2-in-1 type, should be back spliced for approximately 2/3 of the mesh length for best gripping results.
Grip size should be selected by diameter of back splice.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Kellems® Wire Management Products Technical Information
T-20 Dimensions in Inches (cm)
www.hubbell-wiring.com
Overhead Pulling Multiple Strength Grips
Multiple Strength Pulling Grips are designed for pulling aluminum or copper bare conductor, ground wires,
messenger strands, wire rope and insulated cables. They are made of high strength galvanized steel strand
and feature a multi-weave mesh construction of single, double and triple weave for firm holding power.
Application
Kellems Multiple Strength Grips are ideal for overhead transmission and distribution line stringing where
moderate loading is anticipated. They are economical tools for attaching conductors to pulling lines and
double socking for conductor-to-conductor connections.
Rotating Eye Feature
Multiple Strength Grips are available with a forged steel rotating eye which can be attached to a swivel. The
forged eye is durable, compact and streamlined and will thread through blocks and sheaves without binding.
The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling torque when
tension is relaxed. If constant swivel action is required, a swivel should be used. For rotating eye dimensions,
see page T-21. For swivels, see page T-16.
Flexible Eye Feature
Multiple Strength Grips are also available with a flexible, patented wire rope eye. This compact eye will mate
with a swivel, and pass through blocks and sheaves without binding.
Benefits
• Economical, high strength pulling tool.
• Multi-weave construction provides greater strength and holding power.
• Endless Weave Grip end lies flat on the cable and will not snag.
Note: 1. Do not run grips or swivels over bullwheels while under tension.
2. Two Punch-Lok® bands should be firmly attached approximately 1" and 2" (2.54cm and 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release. See page T-15.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Technical Information Kellems® Wire Management Products
F
D
A
3/16 R.
1/8 R.
C
B
T-21
Dimensions in Inches (cm) www.hubbell-wiring.com
Underground Pulling K-Type and T-Type Grips
K-Type Application
Rotating Eye, K-Type Pulling Grips are specially designed for use in the installation of underground power
cables, communication lines and service lines into factories, shopping centers, construction projects and
general underground electrical construction.
Rotating Eye Feature
K-Type Grips come equipped with a forged steel rotating eye which can be attached to a swivel. The forged
eye is durable, compact and streamlined, and will thread through blocks and sheaves without binding.
The rotating eye is not a swivel and will not turn while under tension; it can turn to relieve pulling
torque when the tension is relaxed. If constant swivel action is required, a swivel should be used. For
swivels, see page T-16.
Benefits
• An economical tool for pulling cable.
• Safe, rugged and dependable.
• Equipped with a rotating eye for spin out
of pulling torque after load release.
• Easily installed and removed.
Rotating Eye Dimensions
Rotating Eye
Dimensions
Inches (cm) A B C D F
⁷⁄₈" (2.22) ⁷⁄₈" (2.22) ⁹⁄₃₂" (.71) ¹⁄₂" (1.27) ⁷⁄₈" (2.22) 2⁵⁄₈" (6.67)
1" (2.54) 1" (2.54) ¹⁄₂" (1.27) ⁹⁄₁₆" (1.43) ¹³⁄₁₆" (2.06) 3¹⁄₂" (8.89)
1³⁄₈" (3.49) 1³⁄₈" (3.49) ¹⁄₂" (1.27) ¹¹⁄₁₆" (1.75) 1" (2.54) 4¹⁄₂" (11.43)
1⁵⁄₈" (4.13) 1⁵⁄₈" (4.13) ⁵⁄₈" (1.59) ⁷⁄₈" (2.22) 1³⁄₁₆" (3.02) 5⁵⁄₁₆" (13.49)
1⁷⁄₈" (4.76) 1⁷⁄₈" (4.76) ²¹⁄₃₂"(1.67) 1" (2.54) 1³⁄₈" (3.49) 6¹⁄₈" (15.56)
T-Type
Kellems Flexible T-Type Pulling Grips are made of high strength galvanized steel strand. They feature
double weave mesh for positive holding power in medium to heavy pulling jobs. The grip eye will easily
attach to a swivel.
Application
T-Type Pulling Grips are used for the installation of underground power cables, communication lines and
service lines into factories, construction projects and for general underground electrical construction.
Available in two mesh lengths, short for medium pulls, and standard for general purpose pulling.
Benefits
• Will pull a single cable or cable bundles.
• Patented flexible eye design provides flexibility to follow line of pull.
• A dependable, reusable pulling tool.
• Easily installed and removed.
• Mates easily with a swivel. See page T-16.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Kellems® Wire Management Products Technical Information
T-22 Dimensions in Inches (cm)
www.hubbell-wiring.com
Special Purpose Grips
Non-Conductive Pulling Grips
Kellems Non-Conductive Pulling Grips, made of a high strength, non-conductive aramid fiber, are available
for pulling single cable or cable bundles. Their braided double weave design adds strength and positive
holding power.
Application
Kellems Non-Conductive Pulling Grips were developed for use by utilities for pulling overhead distribution
lines in close proximity to energized lines and hardware.
Benefits
• Color coded for fast on-site selection.
• Extra flexibility for easy installation.
• Non-metallic mesh provides for safe pulls over “hot" areas.
• Pellethane jacketed aramid fiber mesh resists abrasion.
• Grips are corrosion resistant.
Note: Taping is required to guard against accidental release and to insure maximum reliability. Apply vinyl plastic electrical tape starting 2" to 3" (5.08cm to
7.62cm) from the tail of the grip onto 2" to 3" (5.08cm to 7.62cm) of cable.
Slack Pulling Grips
Slack Pulling Grips are offered in three styles made of galvanized steel. The closed type is used when the
cable end is accessible. When not, there are split lace and split rod closing styles. All grips feature single
offset eye for easy attachment to a pulling line.
Application
Slack Grips are widely used in pulling slack for final placement of under ground cable after it has been pulled
in. They are also used for removing cable. Standard mesh lengths are generally used in restricted space for
short pulls. Longer lengths are used for higher pulling loads where space is not restricted.
Benefits
• Easy attachment to pulling lines.
• Reusable rawhide lace for lace closure.
• Galvanized steel for strength.
Note: 1. Replacement rawhide lace. Catalog number 20920002.
2. See page T-44 for lace and rod closing instructions.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Technical Information Kellems® Wire Management Products
T-23
Dimensions in Inches (cm) www.hubbell-wiring.com
Commercial Construction/Light Duty Grips
Light Duty Pulling Grips
Light Duty Pulling Grips are made of galvanized steel in a single weave construction. They feature a flexible
eye for easy attachment to a pulling line.
Application
Light Duty Grips are used in general underground electrical construction where pulling tensions are low.
They are easy tools to use in wiring industrial plants and commercial buildings.
Benefits
• Perfect tools for light pulling jobs.
• Installs easily on cable.
• Strong, galvanized steel construction.
Junior Duty Pulling Grips
Junior Pulling Grips feature a strong galvanized steel, single weave mesh. A flexible eye easily attaches to a
pulling line, snake or fish tape.
Application
Designed to pull building wire, Junior grips are safe tools to use in pulling wire at low tension through conduit
during electrical construction.
Benefits
• Installs easily over building wire.
• Strong secure grip.
• Reusable.
• Pulls single cable or cable bundles.
Junior Grip Kit
Junior Grip Kit contains 6 grips, one of each size. Catalog number 033051114.
Note: See page T-27 for building wire selection chart.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Kellems® Wire Management Products Technical Information
T-24 Dimensions in Inches (cm)
www.hubbell-wiring.com
Splicing Grips
Wire Rope Splicing
Kellems Wire Rope Grips are made of high strength galvanized steel strand in a construction of triple, double
and single weave for superior gripping ability. They are available with or without a rotating barrel which will
help eliminate twist in the old rope from being transferred to the new rope.
Application
Wire Rope Grips are used for changing wire rope on oil derricks, large cranes, overhead cranes and drag
lines. It provides a quick, safe, inexpensive temporary splice. By installing the used wire rope in one end and
the new rope in the other, the new wire rope can be pulled in as the old one is pulled out.
Benefits
• High strength for secure pulling.
• Easy installation.
• Flexible to pass through sheaves and blocks.
Note: 1. During installation each end of the grip should be banded and taped down securely over the rope to insure smooth passage through sheaves and
to guard against accidental release. See page T-15 for end bands.
2. The rotating barrel is not a swivel and will not turn while under tension. It can turn to relieve pulling torque when tension is relaxed.
Cable Splicing
Splicing Grips are made of galvanized steel in double or single weave mesh construction. They are available
in various lengths and sizes to suit most applications.
Application
Splicing Grips are used as a temporary splice for rope, cable or wire rope. They can also be used as cable
reinforcement, and can act as a shield to protect cables and hoses from abrasion.
Benefits
• Easily installed or removed.
• Galvanized steel construction for strength.
• Flexible to follow cable path.
Note: 1. During installation, each end of the splicing grip should be banded and taped down securely to the cable to insure smooth passage with
the cable and guard against accidental release.
2. See page T-15 for end bands.
Kellems® Wire Management Products
Technical Information
Splicing Grips
Technical Information Kellems® Wire Management Products
T-25
Dimensions in Inches (cm) www.hubbell-wiring.com
Accessories
Punch-Lok® Bands
Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from being tripped or pulled loose.
Also, they assure full gripping action by locking the mesh of the tail in tight contact with the cable or rope.
When the tail of a grip is the leading end, the bands are particularly important to prevent accidental release
caused by tripping on obstructions. A conductor-to-conductor (double-socking) pulling operation is a good
example: where two grips connect two conductors to form a temporary splice. Bands should be applied to
the ends of the grips as illustrated on page T-15. It is also common practice to tape over the banded
tail area to assure smooth passage through the sheaves.
The conductor should be installed in the grip up to the elbows of the aluminum shoulders in order to assure
full and complete gripping action. The banding procedure is then followed as illustrated on page T-15.
Note: In all cases two Punch-Lok Bands should be double wrapped approximately 1" to 2" (2.54cm to 5.08cm) from the grip’s tail.
Banding is required to ensure maximum reliability and guard against accidental release.
Swivels
Swivels are essential to the efficiency and safety of any high tension application. They are particularly
important where continuous pulls develop higher and higher torque levels. Torque is intensified by the pull-
resistance of the cable itself and the resistance of the high tension controlling equipment regulating line sag.
Ball bearing swivels release torque and prevent it from reaching dangerous levels that can damage the cable
and obstruct the lines as it passes through sheaves, wheels or blocks.
Kellems® Wire Management Products
Technical Information
Punch-Lok® Bands and Swivels
Kellems® Wire Management Products Technical Information
Punch-Lok® is a registered trademark of Punch-Lok Inc.
T-26 Dimensions in Inches (cm)
www.hubbell-wiring.com
Number of Cables in One Grip
Grip Dia.Range
2 3 4 5 6 and 7 8 9 Inches (cm)
.30-.38 .25-.31 .22-.27 .19-.24 .17-.22 .15-.19 .14-.18 .50-.61
(.76-.97) (.63-.79) (.56-.69) (.48-.60) (.43-.56) (.38-.48) (.36-.46) (1.27-1.55)
.38-.44 .31-.36 .27-.31 .24-.29 .22-.26 .19-.23 .18-.21 .62-.74
(.97-1.12) (.79-.91) (.69-.79) (.61-.74) (.56-.66) (.48-.58) (.46-.53) (1.57-1.88)
.44-.59 .36-.49 .31-.42 .29-.38 .26-.34 .23-.31 .21-.28 .75-.99
(1.12-1.50) (.91-1.24) (.79-1.07) (.74-.97) (.66-.86) (.58-.79) (.53-.71) (1.90-2.51)
.59-.75 .49-.63 .42-.54 .38-.48 .34-.43 .31-.39 .28-.35 1.00-1.24
(1.50-1.90) (1.24-1.60) (1.07-1.37) (.97-1.22) (.86-1.09) (.79-.99) (.71-.89) (2.54-3.15)
.75-.90 .63-.76 .54-.65 .48-.58 .43-.52 .39-.46 .35-.42 1.25-1.49
(1.90-2.29) (1.60-1.93) (1.37-1.65) (1.22-1.47) (1.09-1.32) (.99-1.17) (.89-1.07) (3.17-3.78)
.90-1.07 .76-.89 .65-.77 .58-.67 .52-.60 .46-.54 .42-.49 1.50-1.74
(2.29-2.72) (1.93-2.26) (1.65-1.96) (1.47-1.70) (1.32-1.52) (1.17-1.37) (1.07-1.24) (3.81-4.42)
1.07-1.22 .89-1.02 .77-.88 .67-.77 .60-.69 .54-.62 .49-.56 1.75-1.99
(2.72-3.10) (2.26-2.59) (1.96-2.24) (1.70-1.96) (1.52-1.75) (1.37-1.57) (1.24-1.42) (4.44-5.05)
1.22-1.53 1.02-1.28 .88-1.10 .77-.96 .69-.86 .62-.77 .56-.71 2.00-2.49
(3.10-3.89) (2.59-3.25) (2.24-2.79) (1.96-2.44) (1.75-2.18) (1.57-1.96) (1.42-1.80) (5.08-6.32)
1.53-1.83 1.28-1.53 1.10-1.32 .96-1.16 .86-1.03 .77-.93 .71-.85 2.50-2.99
(3.89-4.65) (3.25-3.89) (2.79-3.35) (2.44-2.95) (2.18-2.62) (1.96-2.36) (1.80-2.16) (6.35-7.59)
1.83-2.14 1.53-1.79 1.32-1.54 1.16-1.35 1.03-1.20 .93-1.08 .85-.99 3.00-3.49
(4.65-5.44) (3.89-4.55) (3.35-3.91) (2.95-3.43) (2.62-3.05) (2.36-2.74) (2.16-2.51) (7.62-8.86)
2.14-2.44 1.79-2.05 1.54-1.76 1.35-1.54 1.20-1.37 1.08-1.24 .99-1.13 3.50-3.99
(5.44-6.20) (4.55-5.21) (3.91-4.47) (3.43-3.91) (3.05-3.48) (2.74-3.15) (2.51-2.87) (8.89-10.13)
2.44-2.75 2.05-2.30 1.76-1.98 1.54-1.74 1.37-1.55 1.24-1.39 1.13-1.27 4.00-4.49
(6.20-6.98) (5.21-5.84) (4.47-5.03) (3.91-4.42) (3.48-3.94) (3.15-3.53) (2.87-3.23) (10.16-11.40)
2.75-3.06 2.30-2.56 1.98-2.20 1.74-1.93 1.55-1.72 1.39-1.55 1.27-1.41 4.50-4.99
(6.98-7.77) (5.84-6.50) (5.03-5.59) (4.42-4.90) (3.94-4.37) (3.53-3.94) (3.23-3.58) (11.43-12.67)
Note: * This chart is not to be used for Conduit Riser Grips. Refer to the chart for Conduit Riser multiple cable section. It is always recommended that, when
multiple cables are installed in a pulling grip, the tail end be banded and tightly taped after installation on the cable bundle. See page T-15 for end bands.
Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters
How to choose the correct grip size:
1. Find the Grip Circumference Range by measuring the circumference
of the bundle of different diameter cables to be gripped (see illustration).
2. Divide the bundle circumference by 3.14 to determine the diameter.
3. Choose a grip offering a range of cable diameters the same as the
cable diameter.
For Pulling Grips*
CAUTION: When a grip is used on multiple cables, the tail end of the grip should be banded after positioning on the cables.
For Cables of Equal Diameters
Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .89" (2.26cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range,
for a Split Grip select the 1.75"-1.99" (4.44cm-5.05cm) range.
Kellems® Wire Management Products
Technical Information
Pulling Grips
Technical Information Kellems® Wire Management Products
T-27
Dimensions in Inches (cm) www.hubbell-wiring.com
Junior Pulling Grip Selection Chart
These charts are a general guide to assist in the selection of the correct Junior Pulling Grip for pulling various
groupings of building wire. It is not intended to be restrictive inasmuch as the use of “dummy" wires (short
pieces of wire used to fill out the Grip) or the tight taping of the wires into a compact bundle may increase
or decrease the number of wires per Grip.
T.H.W.N., T.H.H.N. and X.H.H.W. Building Wire
#14 #12 #10 #8 #6 #4 #3 #2 #1 #1/0
19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 37 Strand 37 Strand
Cable Approx.
Diameter Breaking
Range Strength Catalog
Desc. In. (cm) Lbs. (N) Approximate Number Of Wires In One Grip Number
J 25 .25-.36 450 4-8 3-6 2-3 2 1 1 1 — — — 03305001
(.63-.91) (2,002)
J 37 .37-.49 900 9-16 6-11 4-6 3 2 — — 1 1 1 03305002
(.94-1.24) (4,003)
J 50 .50-.61 1,300 16-25 11-17 7-10 4-5 3-4 2 2 — — — 03305003
(1.27-1.55) (5,782)
J 62 .62-.74 1,950 26-37 18-25 11-14 6-8 5-6 3 3 2 2 — 03305004
(1.57-1.88) (8,674)
J 75 .75-.99 2,800 37-66 26-47 15-27 9-16 6-11 4-7 4-5 3-4 3 2-3 03305005
(1.90-2.51) (12,454)
J 100 1.00-1.24 3,900 66-104 47-74 28-43 16-24 11-17 8-10 6-8 5-7 4-5 4 03305006
(2.54-3.15) (17,347)
R.H.H., R.H., R.W. and R.H.W. Building Wire
#14 #12 #10 #8 #6 #4 #2 #1 #1/0
7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 19 Strand 19 Strand
Cable Approx.
Diameter Breaking
Range Strength Catalog
Desc. In. (cm) Lbs. (N) Approximate Number Of Wires In One Grip Number
J 25 .25-.36 450 2 2 1 1 — — — — — 03305001
(.63-.91) (2,002)
J 37 .37-.49 900 3 2-3 2 — 1 1 1 — — 03305002
(.94-1.24) (4,003)
J 50 .50-.61 1,300 4-5 4-5 3-4 2 — — — 1 — 03305003
(1.27-1.55) (5,782)
J 62 .62-.74 1,950 6-8 6-7 4-5 3 2 2 — — 1 03305004
(1.57-1.88) (8,674)
J 75 .75-.99 2,800 9-16 8-14 6-10 4-6 3-4 3-4 2-3 2 — 03305005
(1.90-2.51) (12,454)
J 100 1.00-1.24 3,900 16-24 15-22 11-16 7-10 5-7 4-6 4 3 2-3 03305006
(2.54-3.15) (17,347)
T.H.W. Building Wire
#14 #12 #10 #8 #6 #4 #2 #1 #1/0
7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 19 Strand
Cable Approx.
Diameter Breaking
Range Strength Catalog
Desc. In. (cm) Lbs. (N) Approximate Number Of Wires In One Grip Number
J 25 .25-.36 450 2-4 2-3 2 1 1 1 — — — 03305001
(.63-.91) (2,002)
J 37 .37-.49 900 5-7 4-5 3-4 2 — — 1 — — 03305002
(.94-1.24) (4,003)
J 50 .50-.61 1,300 8-11 6-8 5-7 3-4 2 2 — 1 1 03305003
(1.27-1.55) (5,782)
J 62 .62-.74 1,950 12-16 9-12 8-10 5-6 3-4 3 2 — — 03305004
(1.57-1.88) (8,674)
J 75 .75-.99 2,800 17-30 13-24 11-19 7-10 5-7 4-5 3-4 2 2 03305005
(1.90-2.51) (12,454)
J 100 1.00-1.24 3,900 31-48 25-37 20-30 11-17 8-11 6-8 5-6 3-4 3 03305006
(2.54-3.15) (17,347)
Kellems® Wire Management Products
Technical Information
Junior Pulling Grips
Kellems® Wire Management Products Technical Information
T-28 www.hubbell-wiring.com
Support Grips - Heavy Duty, Standard Duty, Light Duty Kellems® Wire Management Products
Kellems® Wire Management Products
Support Grips - Heavy Duty, Standard Duty, Light Duty
Solid eye assemblies provide eye reinforcement at support hardware
Four eye styles available: single (shown), double, universal, and offset
Identication tag shows: catalog number, diameter range, agency
approval, and bar code
The strand equalizer positions wires for equal loading throughout the
entire grip length
The positive action mesh grip is designed for light duty up to heavy duty.
Closed grips t over the cable end, split grips wrap around the cable
mid-span. The standard material is nonmagnetic, tin-coated bronze.
Selected items are available in stainless steel. For exceptional immunity
to rust and corrosion with superior strength and exibility for heavy duty
support application in harsh environments; contact the factory
The endless weave provides easy installation onto cable and can be
easily repositioned
T-29
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products
Support Grips - Heavy Duty, Standard Duty, Light Duty
Tin-Coated Bronze/Stainless Steel
Kellems® Wire Management Products Support Grips - Heavy Duty, Standard Duty, Light Duty
Single Eye, Closed Mesh
Single Eye, Split Mesh, Lace Closing
Single Eye, Split Mesh, Rod Closing
T-30 Dimensions in Inches (cm)
www.hubbell-wiring.com
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Single Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 530 (2,357) 7" (17.78) 10" (25.40) 02201013
.63"-.74" (1.60-1.88) 790 (3,514) 8" (20.32) 10" (25.40) 02201014
.75"-.99" (1.90-2.51) 1,020 (4,537) 8" (20.32) 13" (33.02) 02201015
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 9" (22.86) 14" (35.56) 02201017
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 10" (25.40) 15" (38.10) 02201018
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 12" (30.48) 17" (43.18) 02201019
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 14" (35.56) 19" (48.26) 02201020
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 16" (40.64) 21" (53.34) 02201021
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 18" (45.72) 23" (58.42) 02201022
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 21" (53.34) 25" (63.50) 02201023
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 24" (60.96) 27" (68.58) 02201024
Single Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 530 (2,357) 7" (17.78) 10" (25.40) 02202013
.63"-.74" (1.60-1.88) 790 (3,514) 8" (20.32) 10" (25.40) 02202014
.75"-.99" (1.90-2.51) 1,020 (4,537) 8" (20.32) 13" (33.02) 02202015
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 9" (22.86) 14" (35.56) 02202017
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 10" (25.40) 15" (38.10) 02202018
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 12" (30.48) 17" (43.18) 02202019
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 14" (35.56) 19" (48.26) 02202020
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 16" (40.64) 21" (53.34) 02202021
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 18" (45.72) 23" (58.42) 02202022
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 21" (53.34) 25" (63.50) 02202023
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 24" (60.96) 27" (68.58) 02202024
Single Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 790 (3,514) 7" (17.78) 8.5" (21.59) 02203013
.63"-.74" (1.60-1.88) 790 (3,514) 8" (20.32) 8.5" (21.59) 02203014
.75"-.99" (1.90-2.51) 1,020 (4,537) 8" (20.32) 10.5" (26.67) 02203015
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 9" (22.86) 12.5" (31.75) 02203017
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 10" (25.40) 14.5" (36.83) 02203018
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 12" (30.48) 15.5" (39.37) 02203019
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 14" (35.56) 16.5" (41.91) 02203020
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 16" (40.64) 19.5" (49.53) 02203021
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 18" (45.72) 21.5" (54.61) 02203022
3.00"-3.49" (7.62-8.86) 5,750 (25,576) 21" (53.34) 23.5" (59.69) 02203023
3.50"-3.99" (8.89-10.13) 5,750 (25,576) 24" (60.96) 25.5" (64.77) 02203024
Note: E-Eye length.
M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for availability.
Kellems® Wire Management Products
Standard Duty Support Grips
Single Eye, Single Weave, Tin-Coated Bronze
Standard Duty Support Grips Kellems® Wire Management Products
Double Eye, Split Mesh, Rod Closing
Double Eye, Split Mesh, Lace Closing
Double Eye, Closed Mesh
T-31
Dimensions in Inches (cm) www.hubbell-wiring.com
Double Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 530 (2,357) 4" (10.16) 10" (25.40) 02201001
.63"-.74" (1.60-1.88) 790 (3,514) 4" (10.16) 10" (25.40) 02201002
.75"-.99" (1.90-2.51) 1,020 (4,537) 4" (10.16) 13" (33.02) 02201003
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 5" (12.70) 14" (35.56) 02201005
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 5" (12.70) 15" (38.10) 02201006
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 5" (12.70) 17" (43.18) 02201007
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 6" (15.24) 19" (48.26) 02201008
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 6" (15.24) 21" (53.34) 02201009
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 6" (15.24) 23" (58.42) 02201010
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 8" (20.32) 25" (63.50) 02201011
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 8" (20.32) 27" (68.58) 02201012
Double Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 530 (2,357) 4" (10.16) 10" (25.40) 02202001
.63"-.74" (1.60-1.88) 790 (3,514) 4" (10.16) 10" (25.40) 02202002
.75"-.99" (1.90-2.51) 1,020 (4,537) 4" (10.16) 13" (33.02) 02202003
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 5" (12.70) 14" (35.56) 02202005
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 5" (12.70) 15" (38.10) 02202006
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 5" (12.70) 17" (43.18) 02202007
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 6" (15.24) 19" (48.26) 02202008
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 6" (15.24) 21" (53.34) 02202009
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 6" (15.24) 23" (58.42) 02202010
3.00"-3.49" (7.62-8.86) 4,900 (21,795) 8" (20.32) 25" (63.50) 02202011
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 8" (20.32) 27" (68.58) 02202012
Double Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 790 (3,514) 4" (10.16) 8.5" (21.59) 02203001
.63"-.74" (1.60-1.88) 790 (3,514) 4" (10.16) 8.5" (21.59) 02203002
.75"-.99" (1.90-2.51) 1,020 (4,537) 4" (10.16) 10.5" (26.67) 02203003
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 5" (12.70) 12.5" (31.75) 02203005
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 5" (12.70) 14.5" (36.83) 02203006
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 5" (12.70) 15.5" (39.37) 02203007
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 6" (15.24) 16.5" (41.91) 02203008
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 6" (15.24) 19.5" (49.53) 02203009
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 6" (15.24) 21.5" (54.61) 02203010
3.00"-3.49" (7.62-8.86) 5,750 (25,576) 8" (20.32) 23.5" (59.69) 02203011
3.50"-3.99" (8.89-10.13) 5,750 (25,576) 8" (20.32) 25.5" (64.77) 02203012
Note: E-Eye length.
M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for availability.
Kellems® Wire Management Products
Standard Duty Support Grips
Double Eye, Single Weave, Tin-Coated Bronze
Kellems® Wire Management Products Standard Duty Support Grips
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Offset Eye, Split Mesh, Rod Closing
Offset Eye, Split Mesh, Lace Closing
Offset Eye, Closed Mesh
T-32 Dimensions in Inches (cm)
www.hubbell-wiring.com
Offset Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 500 (2,224) 4" (10.16) 10" (25.40) 02201037
.63"-.74" (1.60-1.88) 750 (3,336) 4" (10.16) 10" (25.40) 02201038
.75"-.99" (1.90-2.51) 950 (4,226) 4" (10.16) 13" (33.02) 02201039
1.00"-1.24" (2.54-3.15) 1,500 (6,672) 5" (12.70) 14" (35.56) 02201041
1.25"-1.49" (3.17-3.78) 1,500 (6,672) 5" (12.70) 15" (38.10) 02201042
1.50"-1.74" (3.81-4.42) 1,500 (6,672) 5" (12.70) 17" (43.18) 02201043
1.75"-1.99" (4.44-5.05) 2,000 (8,896) 6" (15.24) 19" (48.26) 02201044
2.00"-2.49" (5.08-6.32) 3,100 (13,789) 9" (22.86) 21" (53.34) 02201045
2.50"-2.99" (6.35-7.59) 3,100 (13,789) 9" (22.86) 23" (58.42) 02201046
3.00"-3.49" (7.62-8.86) 3,800 (16,902) 11" (27.94) 25" (63.50) 02201047
3.50"-3.99" (8.89-10.13) 3,250 (14,480) 11" (27.94) 27" (68.58) 02201048
Offset Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 500 (2,224) 4" (10.16) 10" (25.40) 02202037
.63"-.74" (1.60-1.88) 750 (3,336) 4" (10.16) 10" (25.40) 02202038
.75"-.99" (1.90-2.51) 950 (4,226) 4" (10.16) 13" (33.02) 02202039
1.00"-1.24" (2.54-3.15) 1,500 (6,672) 5" (12.70) 14" (35.56) 02202041
1.25"-1.49" (3.17-3.78) 1,500 (6,672) 5" (12.70) 15" (38.10) 02202042
1.50"-1.74" (3.81-4.42) 1,500 (6,672) 5" (12.70) 17" (43.18) 02202043
1.75"-1.99" (4.44-5.05) 1,800 (8,006) 6" (15.24) 19" (48.26) 02202044
2.00"-2.49" (5.08-6.32) 2,150 (9,563) 9" (22.86) 21" (53.34) 02202045
2.50"-2.99" (6.35-7.59) 2,150 (9,563) 9" (22.86) 23" (58.42) 02202046
3.00"-3.49" (7.62-8.86) 3,250 (14,480) 11" (27.94) 25" (63.50) 02202047
3.50"-3.99" (8.89-10.13) 3,250 (14,480) 11" (27.94) 27" (68.58) 02202048
Offset Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 500 (2,224) 4" (10.16) 7" (17.78) 02203037
.63"-.74" (1.60-1.88) 750 (3,336) 4" (10.16) 9" (22.86) 02203038
.75"-.99" (1.90-2.51) 950 (4,226) 4" (10.16) 10" (25.40) 02203039
1.00"-1.24" (2.54-3.15) 1,500 (6,672) 5" (12.70) 12" (30.48) 02203041
1.25"-1.49" (3.17-3.78) 1,500 (6,672) 5" (12.70) 14" (35.56) 02203042
1.50"-1.74" (3.81-4.42) 1,500 (6,672) 5" (12.70) 15" (38.10) 02203043
1.75"-1.99" (4.44-5.05) 2,000 (8,896) 6" (15.24) 16" (40.64) 02203044
2.00"-2.49" (5.08-6.32) 3,100 (13,789) 9" (22.86) 19" (48.26) 02203045
2.50"-2.99" (6.35-7.59) 3,100 (13,789) 9" (22.86) 20" (50.80) 02203046
3.00"-3.49" (7.62-8.86) 4,300 (19,126) 11" (27.94) 21" (53.34) 02203047
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 11" (27.94) 21" (53.34) 02203048
Note: E-Eye length.
M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for availability.
Standard Duty Support Grips Kellems® Wire Management Products
Kellems® Wire Management Products
Standard Duty Support Grips
Offset Eye, Single Weave, Tin-Coated Bronze
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Universal Eye, Split Mesh, Rod Closing
Universal Eye, Split Mesh, Lace Closing
Universal Eye, Closed Mesh
T-33
Dimensions in Inches (cm) www.hubbell-wiring.com
Universal Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 530 (2,357) 18" (45.72) 10" (25.40) 02201051
.63"-.74" (1.60-1.88) 790 (3,514) 18" (45.72) 10" (25.40) 02201052
.75"-.99" (1.90-2.51) 1,020 (4,537) 18" (45.72) 13" (33.02) 02201053
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 18" (45.72) 14" (35.56) 02201050
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 18" (45.72) 15" (38.10) 02201054
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 18" (45.72) 17" (43.18) 02201055
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 18" (45.72) 19" (48.26) 02201056
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 18" (45.72) 21" (53.34) 02201057
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 18" (45.72) 23" (58.42) 02201058
Universal Eye, Split Mesh, Lace Closing
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 530 (2,357) 18" (45.72) 10" (25.40) 02202050
.63"-.74" (1.60-1.88) 790 (3,514) 18" (45.72) 10" (25.40) 02202051
.75"-.99" (1.90-2.51) 1,020 (4,537) 18" (45.72) 13" (33.02) 02202052
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 18" (45.72) 14" (35.56) 02202054
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 18" (45.72) 15" (38.10) 02202055
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 18" (45.72) 17" (43.18) 02202056
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 18" (45.72) 19" (48.26) 02202057
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 18" (45.72) 21" (53.34) 02202058
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 18" (45.72) 23" (58.42) 02202059
3.50"-3.99" (8.89-10.13) 4,900 (21,795) 18" (45.72) 27" (68.58) 02202061
Universal Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.50"-.62" (1.27-1.57) 790 (3,514) 18" (45.72) 8.5" (21.59) 02203064
.63"-.74" (1.60-1.88) 790 (3,514) 18" (45.72) 8.5" (21.59) 02203065
.75"-.99" (1.90-2.51) 1,020 (4,537) 18" (45.72) 10.5" (26.67) 02203066
1.00"-1.24" (2.54-3.15) 1,610 (7,161) 18" (45.72) 12.5" (31.75) 02203068
1.25"-1.49" (3.17-3.78) 1,610 (7,161) 18" (45.72) 14.5" (36.83) 02203069
1.50"-1.74" (3.81-4.42) 1,610 (7,161) 18" (45.72) 15.5" (39.37) 02203070
1.75"-1.99" (4.44-5.05) 2,150 (9,563) 18" (45.72) 16.5" (41.91) 02203071
2.00"-2.49" (5.08-6.32) 3,260 (14,500) 18" (45.72) 19.5" (49.53) 02203072
2.50"-2.99" (6.35-7.59) 3,260 (14,500) 18" (45.72) 21.5" (54.61) 02203073
3.00"-3.49" (7.62-8.86) 5,750 (25,576) 18" (45.72) 23.5" (59.69) 02203074
Note: E-Eye length.
M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for availability.
Kellems® Wire Management Products Standard Duty Support Grips
Kellems® Wire Management Products
Standard Duty Support Grips
Universal Eye, Single Weave, Tin-Coated Bronze
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Single Eye, Split Mesh, Lace Closing
Heavy Duty, Single Eye, Closed Mesh
T-34 Dimensions in Inches (cm)
www.hubbell-wiring.com
Heavy Duty, Single Eye, Closed Mesh*
For heavy duty permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.75"-.99" (1.90-2.51) 2,820 (12,543) 10" (25.40) 25" (63.50) 02206010
1.00"-1.24" (2.54-3.15) 4,280 (19,037) 12" (30.48) 28" (71.12) 02206011
1.25"-1.49" (3.17-3.78) 4,280 (19,037) 12" (30.48) 30" (76.20) 02206012
1.50"-1.99" (3.81-5.05) 4,280 (19,037) 12" (30.48) 34" (86.36) 02206013
Single Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.75"-.99" (1.90-2.51) 2,820 (12,543) 10" (25.40) 25" (63.50) 02207010
1.00"-1.24" (2.54-3.15) 4,280 (19,037) 12" (30.48) 28" (71.12) 02207011
1.25"-1.49" (3.17-3.78) 4,280 (19,037) 12" (30.48) 30" (76.20) 02207012
1.50"-1.99" (3.81-5.05) 4,280 (19,037) 12" (30.48) 34" (86.36) 02207013
Note: E-Eye length.
M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for availability.
Heavy Duty Support Grips Kellems® Wire Management Products
Kellems® Wire Management Products
Heavy Duty Support Grips
Single Eye, Double Weave, Tin-Coated Bronze
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Double Eye, Split Mesh, Lace Closing
Double Eye, Closed Mesh
T-35
Dimensions in Inches (cm) www.hubbell-wiring.com
Double Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.75"- .99"(1.90-2.51) 2,820 (12,543) 10" (25.40) 25" (63.50) 02206001
1.00"-1.24" (2.54-3.15) 4,280 (19,037) 10" (25.40) 28" (71.12) 02206002
1.25"-1.49" (3.17-3.78) 4,280 (19,037) 10" (25.40) 30" (76.20) 02206003
1.50"-1.99" (3.81-5.05) 4,280 (19,037) 10" (25.40) 34" (86.36) 02206004
2.00"-2.49" (5.08-6.32) 8,050 (35,806) 12" (30.48) 36" (91.44) 02206005
2.50"-2.99" (6.35-7.59) 8,050 (35,806) 12" (30.48) 38" (96.52) 02206006
3.00"-3.49" (7.62-8.86) 10,060 (44,747) 12" (30.48) 40" (101.60) 02206007
3.50"-3.99" (8.89-10.13) 12,070 (53,687) 12" (30.48) 44" (111.76) 02206008
4.00"-4.49" (10.16-11.40) 12,070 (53,687) 12" (30.48) 46" (116.84) 02206009
4.50"-4.99" (11.43-12.67) 12,070 (53,687) 12" (30.48) 68" (172.72) 02208009
Double Eye, Split Mesh, Lace Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.75"-.99" (1.90-2.51) 2,820 (12,543) 10" (25.40) 25" (63.50) 02207001
1.00"-1.24" (2.54-3.15) 4,280 (19,037) 10" (25.40) 28" (71.12) 02207002
1.25"-1.49" (3.17-3.78) 4,280 (19,037) 10" (25.40) 30" (76.20) 02207003
1.50"-1.99" (3.81-5.05) 4,280 (19,037) 10" (25.40) 34" (86.36) 02207004
2.00"-2.49" (5.08-6.32) 8,050 (35,806) 12" (30.48) 36" (91.44) 02207005
2.50"-2.99" (6.35-7.59) 8,050 (35,806) 12" (30.48) 38" (96.52) 02207006
3.00"-3.49" (7.62-8.86) 10,060 (44,747) 12" (30.48) 40" (101.60) 02207007
3.50"-3.99" (8.89-10.13) 12,070 (53,687) 12" (30.48) 44" (111.76) 02207008
4.00"-4.49" (10.16-11.40) 12,070 (53,687) 12" (30.48) 46" (116.84) 02207009
4.50"-4.99" (11.43-12.67) 12,070 (53,687) 12" (30.48) 68" (172.72) 02209009
Note: E-Eye length.
M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for availability.
Kellems® Wire Management Products Heavy Duty Support Grips
Kellems® Wire Management Products
Heavy Duty Support Grips
Double Eye, Double Weave, Tin-Coated Bronze
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
.3125''
(.80) Dia.
.250''
(.64)
4.875''
(12.38)
2.000''
(5.08)
Screw Hook
Catalog Number 20303001
Yield Strength 900 lbs (4003 N)
Heavy Duty, Single Eye, Closed Mesh,
Multi-Weave
Light Duty, Single Eye, Closed Mesh,
Single Weave
T-36 Dimensions in Inches (cm)
www.hubbell-wiring.com
Light Duty, Single Eye, Closed Mesh, Single Weave
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.23"-.31" (.58-.79) 290 (1,290) 3" (7.62) 3.75" (9.52) 02216001
.29"-.37" (.74-.94) 290 (1,290) 5" (12.70) 4.25" (10.79) 02216002
.35"-.44" (.89-1.12) 500 (2,224) 5.5" (13.97) 4.75" (12.06) 02216003
.41"-.50" (1.04-1.27) 500 (2,224) 5.5" (13.97) 5" (12.70) 02216004
.46"-.56" (1.17-1.42) 660 (2,936) 6" (15.24) 5.25" (13.33) 02216005
.52"-.62" (1.32-1.57) 790 (3,514) 7" (17.78) 6.25" (15.87) 02216006
.58"-.68" (1.47-1.73) 790 (3,514) 7" (17.78) 6¹⁄₂" (16.51) 02216007
.64"-.75" (1.63-1.90) 790 (3,514) 7" (17.78) 6.75" (17.14) 02216008
.70"-.81" (1.78-2.06) 790 (3,514) 7" (17.78) 7.25" (18.41) 02216009
.75"-.87" (1.90-2.21) 1,020 (4,537) 8" (20.32) 8" (20.32) 02216010
.81"-.94" (2.06-2.39) 1,020 (4,537) 8" (20.32) 8.25" (20.95) 02216011
.87"-1.00" (2.21-2.54) 1,020 (4,537) 8" (20.32) 8.75" (22.22) 02216012
.94"-1.06" (2.39-2.69) 1,020 (4,537) 9" (22.86) 9" (22.86) 02216013
1.00"-1.18" (2.54-3.00) 1,020 (4,537) 9" (22.86) 9.5" (24.13) 02216014
1.06"-1.25" (2.69-3.17) 1,020 (4,537) 9" (22.86) 9.5" (24.13) 02216015
Heavy Duty, Single Eye, Closed Mesh, Multi-Weave
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.23"-.31" (.58-.79) 500 (2,224) 5" (12.70) 4.5" (11.43) 02217001
.29"-.37" (.74-.94) 500 (2,224) 5" (12.70) 5.5" (13.97) 02217002
.35"-.44" (.89-1.12) 870 (3,870) 6" (15.24) 6.5" (16.51) 02217003
.41"-.50" (1.04-1.27) 870 (3,870) 6" (15.24) 7.5" (19.05) 02217004
.46"-.56" (1.17-1.42) 1,050 (4,670) 6" (15.24) 8" (20.32) 02217005
.52"-.62" (1.32-1.57) 1,050 (4,670) 7" (17.78) 8.5" (21.59) 02217006
.58"-.68" (1.47-1.73) 1,050 (4,670) 7" (17.78) 9.5" (24.13) 02217007
.64"-.75" (1.63-1.90) 1,390 (6,183) 7" (17.78) 9.5" (24.13) 02217008
.70"-.81" (1.78-2.06) 1,390 (6,183) 8" (20.32) 10.5" (26.67) 02217009
.75"-.87" (1.90-2.21) 1,390 (6,183) 8" (20.32) 10.5" (26.67) 02217010
.81"-.94" (2.06-2.39) 1,390 (6,183) 8" (20.32) 10.5" (26.67) 02217011
.87"-1.00" (2.21-2.54) 1,790 (7,962) 8" (20.32) 11.5" (29.21) 02217012
.94"-1.06" (2.39-2.69) 1,790 (7,962) 9" (22.86) 12.5" (31.75) 02217013
1.00"-1.18" (2.54-3.00) 1,790 (7,962) 9" (22.86) 13.5" (34.29) 02217014
1.06"-1.25" (2.69-3.17) 1,790 (7,962) 9" (22.86) 14.5" (36.83) 02217015
Note: E-Eye length.
M-Mesh length at nominal diameter.
Service Drop Grips Kellems® Wire Management Products
Kellems® Wire Management Products
Service Drop Grips
Single Eye, Tin-Coated Bronze
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Light Duty, Universal Eye,
Closed Mesh, Single Weave
Heavy Duty, Universal Eye,
Closed Mesh, Multi-Weave
T-37
Dimensions in Inches (cm) www.hubbell-wiring.com
Light Duty, Universal Eye, Closed Mesh, Single Weave
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.23"-.31" (.58-.79) 290 (1,290) 9" (22.86) 3.75" (9.52) 02216016
.29"-.37" (.74-.94) 290 (1,290) 10" (25.40) 4.25" (10.79) 02216017
.35"-.44" (.89-1.12) 500 (2,224) 10" (25.40) 4.75" (12.06) 02216018
.41"-.50" (1.04-1.27) 500 (2,224) 11" (27.94) 5" (12.70) 02216019
.46"-.56" (1.17-1.42) 660 (2,936) 12" (30.48) 5.25" (13.33) 02216020
.52"-.62" (1.32-1.57) 790 (3,514) 13" (33.02) 6.25" (15.87) 02216021
.58"-.68" (1.47-1.73) 790 (3,514) 13" (33.02) 6.5" (16.51) 02216022
.64"-.75" (1.63-1.90) 790 (3,514) 13" (33.02) 6.75" (17.14) 02216023
.70"-.81" (1.78-2.06) 790 (3,514) 13" (33.02) 7.25" (18.41) 02216024
.75"-.87" (1.90-2.21) 1,020 (4,537) 14" (35.56) 8" (20.32) 02216025
.81"-.94" (2.06-2.39) 1,020 (4,537) 14" (35.56) 8.25" (20.95) 02216026
.87"-1.00" (2.21-2.54) 1,020 (4,537) 14" (35.56) 8.75" (22.22) 02216027
.94"-1.06" (2.39-2.69) 1,020 (4,537) 15" (38.10) 9" (22.86) 02216028
1.00"-1.18" (2.54-3.00) 1,020 (4,537) 15" (38.10) 9.5" (24.13) 02216029
1.06"-1.25" (2.69-3.17) 1,020 (4,537) 15" (38.10) 9.5" (24.13) 02216030
Heavy Duty, Universal Eye, Closed Mesh, Multi-Weave
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.23"-.31" (.58-.79) 500 (2,224) 11" (27.94) 4.5" (11.43) 02217016
.28"-.37" (.74-.94) 500 (2,224) 11" (27.94) 5.5" (13.97) 02217017
.35"-.44" (.89-1.12) 870 (3,870) 12" (30.48) 6.5" (16.51) 02217018
.41"-.50" (1.04-1.27) 870 (3,870) 12" (30.48) 7.5" (19.05) 02217019
.46"-.56" (1.17-1.42) 1,050 (4,670) 12" (30.48) 8" (20.32) 02217020
.52"-.62" (1.32-1.57) 1,050 (4,670) 13" (33.02) 8.5" (21.59) 02217021
.58"-.68" (1.47-1.73) 1,050 (4,670) 13" (33.02) 9.5" (24.13) 02217022
.64"-.75" (1.63-1.90) 1,390 (6,183) 13" (33.02) 9.5" (24.13) 02217023
.70"-.81" (1.78-2.06) 1,390 (6,183) 14" (35.56) 10.5" (26.67) 02217024
.75"-.87" (1.90-2.21) 1,390 (6,183) 14" (35.56) 10.5" (26.67) 02217025
.81"-.94" (2.06-2.39) 1,390 (6,183) 14" (35.56) 10.5" (26.67) 02217026
.87"-1.00" (2.21-2.54) 1,790 (7,962) 14" (35.56) 11.5" (29.21) 02217027
.94"-1.06" (2.39-2.69) 1,790 (7,962) 15" (38.10) 12.5" (31.75) 02217028
1.00"-1.18" (2.54-3.00) 1,790 (7,962) 15" (38.10) 13.5" (34.29) 02217029
1.06"-1.25" (2.69-3.17) 1,790 (7,962) 15" (38.10) 14.5" (36.83) 02217030
Note: E-Eye length.
M-Mesh length at nominal diameter.
Kellems® Wire Management Products Service Drop Grips
Kellems® Wire Management Products
Service Drop Grips
Universal Eye, Tin-Coated Bronze
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
Strain
Relief
Grip
Bus
Drop
Grips
Motor Box
Safety Spring
Strain
Relief
Grip
Single Eye, Wide Range
Safety Spring
Universal Eye, Wide Range
T-38 Dimensions in Inches (cm)
www.hubbell-wiring.com
Safety Spring
Maximum Approx.
Deflection Breaking Length* Diameter
Inches/Lbs Strength Inches Inches Model Catalog
(cm/N) Lbs. (N) (cm) (cm) Lbs. (N) Number
2¾" at 40 lbs. 500 8.25" .75" 40 lb. spring 20302001
(6.98 cm at 178 N) (2,224) (20.95) (1.90) (178)
3¹⁄⁄" at 80 lbs. 850 8.25" 1" 80 lb. spring 20302002
(7.94 cm at 356 N) (3,781) (20.95) (2.54) (356)
Note: Springs can be used with single eye grips by disassembling drawbar from coil, placing through eye
and replacing drawbar.
* No load.
Single Eye, Wide Range
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.24"-.32" (.61-.81) 350 (1,557) 3" (7.62) 3.5" (8.89) 073041276**
.32"-.43" (.81-1.09) 450 (2,002) 4" (10.16) 4" (10.16) 073041277
.43"-.56" (1.09-1.42) 550 (2,446) 6" (15.24) 4.75" (12.06) 073041278
.56"-.73" (1.42-1.85) 1,000 (4,448) 7" (17.78) 6" (15.24) 073041279
.73"-.85" (1.85-2.16) 1,400 (6,227) 7" (17.78) 6.75" (17.14) 073041280
.85"-1.00" (2.16-2.54) 1,400 (6,227) 8" (20.32) 8" (20.32) 073041281
1.00"-1.25" (2.54-3.17) 1,500 (6,672) 9" (22.86) 9.5" (24.13) 073041282
Universal Eye, Wide Range
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Number
.32"-.43" (.81-1.09) 450 (2,002) 10" (25.40) 4" (10.16) 073041284
.43"-.56" (1.09-1.42) 550 (2,446) 12" (30.48) 4.75" (12.06) 073041285
.56"-.73" (1.42-1.85) 1,000 (4,448) 13" (33.02) 6" (15.24) 073041286
.73"-.85" (1.85-2.16) 1,400 (6,227) 13" (33.02) 6.75" (17.14) 073041287
.85"-1.00" (2.16-2.54) 1,400 (6,227) 14" (35.56) 8" (20.32) 073041288
1.00"-1.25" (2.54-3.17) 1,500 (6,672) 15" (38.10) 9.5" (24.13) 073041289
Note: E-Eye length.
M-Mesh length at nominal diameter.
** Item indicated is not UL listed.
Bus Drop Grips and Safety Springs
Kellems Bus Drop Grips are offered with either a single eye or universal
bale attachment. The mesh is single weave galvanized steel with the patented
wide range construction. They are suitable for indoor use only. Consult Technical
Service for Stainless Steel Grips.
Application
Bus Drop Grips provide a safe, easy and economical method to support flexible cord or
bus drop cable at bus duct and other industrial areas.
Benefits
• Easily installed.
• Absorb tension, vibration and pull with no cable damage.
• Patented mesh construction.
Safety Spring
Springs can be used with single eye grips by disassembling drawbar from coil, placing
through eye and replacing drawbar.
Bus Drop Support Grips Kellems® Wire Management Products
Kellems® Wire Management Products
Bus Drop Support Grips
Single Eye, Universal Eye, Galvanized Steel
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-42 through T-46.
T-39
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Conduit Riser Grips
Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only
Cable Sizes .50"- .62" .63"-.74" .75"- .99" 1.00"- 1.24" 1.25"- 1.49" 1.50"-1.74" 1.75"-1.99" 2.00"- 2.49" 2.50" -2.99" 3.00"- 3.49" 3.50"- 3.99"
Inches (cm) (1.27-1.57) (1.60-1-88) (1.90-2.51) (2.54-3.15) (3.17-3.78) (3.81-4.42) (4.44-5.05) (5.08-6.32) (6.35-7.59) (7.62-8.86) (8.89-10.13)
Model R050 R062 R075 R100 R125 R150 R175 R200 R250 R300 R350
Length
Inches (cm) 8" (20.32) 9" (22.86) 11" (27.94) 12" (30.48) 12" (30.48) 14" (35.56) 15" (38.10) 17" (43.18) 18" (45.72) 20" (50.80) 21" (53.34)
Conduit
Sizes Catalog Number
Inches Approx. Breaking Strength Lbs. (N)
¾ 02211106 — — — — — — — — — —
530 (2,357)
1 02211100 02211101 — — — — — — — — —
490 (2,179) 790 (3,514)
1¼ 02211001 02211002 02211003 — — — — — — — —
450 (2,002) 740 (3,292) 1,030 (4,581)
1½ — 02211006 02211007 02211009 — — — — — — —
690 (3,069) 970 (4,315) 1,610 (7,161)
2 — 02211107 02211010 02211012 02211013 — — — — — —
640 (2,847) 920 (4,092) 1,520 (6,761) 1,610 (7,161)
2½ — — — — 02211017 02211018 02211019 — — — —
1,510 (6,716) 1,610 (7,161) 2,150 (9,563)
3 — — — 02211022 02211023 02211024 02211025 02211026 — — —
1,340 (5,960) 1,400 (6,227) 1,490 (6,627) 1,990 (8,851) 3,260 (14,500)
3½ — — — — — — — 02211033 02211034 — —
2,970 (13,211) 3,260 (14,500)
4 — — — — — — 02211040 02211041 02211042 02211043 —
1,670 (7,248) 2,680 (11,921) 2,890 (12,855) 4,080 (18,148)
5 — — — — — — — — 02211061 02211062 02211063
2,150 (9,563) 2,860 (12,721) 3,130 (13,922)
6 — — — — — — — — — 02211072 02211073
2,245 (9,986) 2,245 (9,986)
Note: See page T-47 for multiple cables in a single conduit riser grip.
Wire Management Products
Conduit Riser Grips
Ring Type, Single Weave, Tin-Coated Bronze
WARNING!
It is important that you read all breaking strength, safety and technical
data relating to this product on pages T-47 and T-48.
Single Weave, Closed Mesh
Kellems® Conduit Riser Support Grips are available in closed mesh and
in split mesh with lace or rod closures, to cover all applications including
single cable or multiple wire support. Refer to technical section, T-47 for
grip selection assistance for cable bundles. The standard material is tin-
coated bronze strand. The grip is permanently fastened to a support ring,
resulting in a one piece unit which will allow air ventilation within the
conduit. The ring will fit standard electrical rigid metal conduit and
schedule 40 rigid PVC conduit only. See page T-48 for ring dimensions.
For permanent support when cable end is available to be installed
through the grip.
T-40 Dimensions in Inches (cm)
www.hubbell-wiring.com
Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only
Cable Sizes .75"- .99" 1.00"- 1.24" 1.25"- 1.49" 1.50"-1.74" 1.75"- 1.99" 2.00"- 2.49" 2.50"- 2.99" 3.00"- 3.49" 3.50" -3.99"
Inches (cm) (1.90-2.51) (2.54-3.15) (3.17-3.78) (3.81-4.42) (4.44-5.05) (5.08-6.32) (6.35-7.59) (7.62-8.86) (8.89-10.13)
Model RS075 RS100 RS125 RS150 RS175 RS200 RS250 RS300 RS350
Length 11" (27.94) 12" (30.48) 12" (30.48) 14" (35.56) 15" (38.10) 17" (43.18) 18" (45.72) 20" (50.80) 21" (53.34)
Inches (cm)
Conduit Sizes Catalog Number
Inches Approx. Breaking Strength Lbs. (N)
1¼ 02212003 — — — — — — — —
1,580 (7,028)
1½ 02212007 — — — — — — — —
1,500 (6,672)
2 02212010 02212012 02212013 — — — — — —
1,430 (6,361) 1,930 (8,585) 2,040 (9,074)
2½ — — 02212017 02212018 — — — — —
1,910 (8,496) 2,040 (9,074)
3 — — 02212023 02212024 02212025 02212026 — — —
1,780 (7,917) 1,890 (8,407) 2,520 (11,209) 4,300 (19,126)
3½ — — — — — 02212033 02212034 — —
3,910 (17,392) 4,300 (19,126)
4 — — — — 02212040 02212041 02212042 02212043 —
2,110 (9,385) 3,530 (15,701) 3,820 (16,991) 5,380 (23,930)
5 — — — — — — 02212061 — —
2,860 (12,721)
6 — — — — — — — — 02212073
2,955 (13,144)
Note: See page T-47 for multiple cables in a single conduit riser grip.
WARNING!
It is important that you read all breaking strength, safety
and technical data relating to this product on pages T-47
and T-48.
Double Weave, Split Mesh, Lace Closing
Kellems® Conduit Riser Support Grips will support cable
runs in vertical or sloping standard rigid conduit. The grip
is fastened to a support ring which seats on the rim of the
conduit. The entire grip is supported by the conduit itself
and no other hardware is required. See page T-48 for
ring dimensions. The rings will fit schedule 40 rigid PVC
conduit and standard electrical rigid metal conduit only.
For permanent support when cable end is not available.
Kellems® Wire Management Products
Conduit Riser Grips
Ring Type, Double Weave, Tin-Coated Bronze
Conduit Riser Grips Kellems® Wire Management Products
T-41
Dimensions in Inches (cm) www.hubbell-wiring.com
Suitable For Standard Electrical Rigid Metal Conduit and Schedule 40 Rigid PVC Conduit Only
Cable Sizes
.75"- .99" 1.00"- 1.24" 1.25"- 1.49" 1.50"- 1.74" 1.75"-1.99" 2.00"- 2.49" 2.50"- 2.99" 3.00"-3.49" 3.50"-3.99"
Inches (cm)
(1.90-2.51) (2.54-3.15) (3.17-3.78) (3.81-4.42) (4.44-5.05) (5.08-6.32) (6.35-7.59) (7.62-8.86) (8.89-10.13)
Model RR075 RR100 RR125 RR150 RR175 RR200 RR250 RR300 RR350
Length
Inches (cm)
11" (27.94) 12" (30.48) 13" (33.02) 14" (35.56) 15" (38.10) 16" (40.64) 18" (45.72) 19" (48.26) 21" (53.34)
Conduit Sizes Catalog Number
Inches Approx. Breaking Strength Lbs. (N)
1¼ 02213003 — — — — — — — —
1,020 (4,537)
1½ 02213007 02213009 — — — — — — —
970 (4,315) 1,610 (7,161)
2 — 02213012 02213013 — — — — —
—
1,520 (6,761) 1,610 (7,161)
2½ — — 02213017 02213018 — — — — —
1,510 (6,716) 1,610 (7,161)
3 — — 02213023 02213024 02213025 02213026 — — —
1,400 (6,227) 1,490 (6,627) 1,990 (8,851) 3,260 (14,500)
3½ — — — — — 02213033 — — —
2,970 (13,211)
4 — — — — — 02213041 02213042 — —
2,670 (11,876) 2,890 (12,855)
Note: See page T-47 for multiple cables in a single conduit riser grip.
Kellems® Wire Management Products
Conduit Riser Grips
Ring Type, Single Weave, Tin-Coated Bronze
WARNING!
It is important that you read all breaking strength, safety
and technical data relating to this product on pages T-47
and T-48.
Single Weave, Split Mesh, Rod Closing Benefits
• Easy and fast to install.
• Will not damage electrical cable.
• Allows cable to expand or contract.
• Ideal way to hold cable in vertical conduit.
• Prevents cable creep in conduit.
• Helps prevent cable pullouts.
• The rings will fit schedule 40 rigid PVC conduit and
standard electrical rigid metal conduit only.
• For support when cable end is not available.
Kellems® Wire Management Products Conduit Riser Grips
T-42 Dimensions in Inches (cm)
www.hubbell-wiring.com
Support Grip Selection Chart
Grip Styles Application Page
Closed mesh Standard, permanent support, cable end available. T-30 to T-38
Split lace closing Standard, permanent support, cable end unavailable. T-30 to T-35
Split rod closing Standard, temporary support, cable end unavailable. Tape or band tail T-30 to T-33
end of wire mesh grip after positioning for permanent support.
Material* Tin-coated bronze standard or stainless steel by special request. T-30 to T-41
Standard support grips Support vertical runs to 99 ft. loads to 600 lbs. T-30 to T-33
Heavy duty grips Support vertical runs over 100 ft. loads over 600 lbs. T-34, T-35
Service drop Light duty to support service entrance cable. T-36, T-37
Bus drop Light duty support, indoors only, on Bus drop cable. T-38
Conduit riser Support cable runs in rigid (Schedule 40) conduit. T-39 to T-41
Fiber optic cable support grips Support fiber optic cable. T-53
Note: * Most catalog listed support grips are made of tin-coated bronze strand. To order stainless steel support grips, change the first three catalog number
digits from 022-0x-xxx to 024-0x-xxx. Consult Technical Service for details.
Eye Styles
Select the Correct Support Grip
Each Kellems grip is designed to work on a specific
range of cable diameters.
Step 1 Refer to the Kellems chart below to determine
the grip style best suited for your application.
Step 2 Determine your cable outside diameter.
Step 3 Find the grip size that encompasses your
cable diameter.
Step 4 Whenever possible, use a closed mesh that
assembles over the cable end. If the cable end
is not available, use a split mesh.
Step 5 Where available, select an eye style that suits
your needs.
Step 6 Select the proper material—tinned bronze or
stainless steel*.
Step 7 Estimate the tension to be put on the grip,
establish the working load you require and
compare this to the listed approximate breaking
strength of the grip to insure that the grip will be
strong enough. Refer to page T-43 for safety
and working load considerations.
CAUTION: It is very important to comply with all of the
following precautions.
1. Support grips are to be installed by a qualified individual
in accordance with all applicable national and local
safety, electrical and rigging codes.
2. Ensure that the correct grip is selected for your specific
needs.
3. Do not use a support grip for any application other than
supporting cable.
4. Thoroughly examine the grip for damage. Do not use a
damaged grip.
5. Ensure that the recommended work load of the grip is
suitable for the application. Never use grips at their
approximated rated breaking strength. A safety factor
of 10 is recommended for support grips.
6. Do not alter grips in any way. For example, do not
flatten, straighten, bend or otherwise modify eye tubes,
hooks, and strand equalizers.
7. Do not attach any type of hook, clamp or other hardware
directly to the stranded bale of a “U” eye support grip.
The formed eye tube is the only acceptable means of
attachment to external hardware.
8. Always apply 2 bands at 1" and 2" respectively, from
the tail end of the mesh to guard against accidental
release of the grip. Accidental release can occur if an
object contracts and pushes against the tail end of the
mesh, thereby expanding and releasing it’s hold.
Kellems® Wire Management Products
Technical Information
Support Grips
Kellems Support Grips
Kellems Support Grips are used to hold the weight of electrical cable as it hangs in a vertical, sloping or horizontal position.
Electrical cable must be supported, or its dead weight can cause excessive strain or pullout at the connections resulting
in power failure. Support grips also absorb additional strain from flexure, vibration, expansion and contraction. Kellems
Support Grips listed in this catalog are made of high grade, non-magnetic tin-coated bronze strand. Stainless steel grips,
made of alloy 302–304 SST for severe service or unusual environmental conditions, are available on request.
Single Double Universal Offset
Technical Information Kellems® Wire Management Products
T-43
Dimensions in Inches (cm) www.hubbell-wiring.com
Examples
Approx. Breaking Safety Max. Rec. Catalog
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Number
Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027
Support Grips 1,610 (7,161) 10 161 (716) 02202019
The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety
to take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable for the application.
The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to the metric
unit of weight (kilograms) the conversion factor is 9.808 newtons/kilogram.
Support Grip Materials
Material Features Grip Type
Tin-coated bronze wire • Corrosion resistant for normal outside areas •Support grips
• Non-magnetic • Service drop grips
• Moderate strength • Conduit riser grips
Stainless steel wire (302-304) • High strength • Support grips
• Corrosion resistant • Hose containment grips
Galvanized steel wire • Slightly magnetic • Bus drop grips
• Not subject to continuous outside environment
Approvals
CSA Certifications are indicated on appropriate product catalog pages.
Note: It is always recommended that the tail end of the grip be banded after the installation on the cable to prevent accidental release of the mesh.
See page T-15 for end bands.
Kellems® Wire Management Products
Technical Information
Support Grips
The broad application of Kellems grips on a wide variety
of objects requires that adequate safety factors be used
to establish working loads. The approximate breaking
strength of a Kellems grip represents an average
calculation based on data established from actual direct
tension testing done in our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are
never the same. The tension, diameter, movement,
number of objects gripped, gripping surface, and the
attachments used are just some of the factors which
vary with each application. These factors, together with
the effects of abrasion, corrosion, prior use or abuse
and any other variables of a specific application, must
be considered by the user and the grip replaced as
appropriate. Where the conditions of the application
are not well defined or known, or where risk of injury to
persons or property is involved, a greater safety factor
should be utilized.
Under normal conditions, Kellems’ recommended factor
of safety is five for catalog listed pulling grips, and ten
for catalog listed support grips.
Any warranty as to quality, performance or fitness for use
of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored, handled,
used, maintained, and inspected by the user at a frequency
appropriate for the use and condition of the grip.
Safety And Working Load Factors For Wire Mesh Grips
Kellems® Wire Management Products Technical Information
T-44 Dimensions in Inches (cm)
www.hubbell-wiring.com
Split Support Grip Lace Closing Instructions
Single Weave Grips should be laced with single strand lacing; double weave with double strand. Lacing
strands should be the same material as the grip. Kellems supplies the appropriate lacing with each grip.
1. Start the lacing at the lead or anchoring end of the grip. Thread the lacings through the first two loops of
the split and pull through until the lacings are centered at this point. Lace as you would your shoe,
crossing the lacings before lacing the next two loops.
2. Don’t pull lacing too tight. Leave a space between adjoining loops approximately equal to the width of
one diamond of the mesh.
3. Twist the lacing strands tightly together at the tail end of the grip.
4. Wrap the ends of the lacings once or twice tightly around the tail of the grip, twisting the ends together
securely. Excess lace can be cut off.
Split Support Grip Rod Closing Instructions
The stainless steel rod is a precise built-in feature which makes threading easy and fast. The strands of the
mesh pass around the rod and match up with the strands from the opposite direction. The rod does not
touch the cable at any point and therefore cannot cut the cable. Rod Closing Grips are reusable. They may
be removed and reused as many times as desired.
1. Fast to install
Wrap the grip around the cable and thread the rod through the pre-formed loops with a corkscrew motion,
using the curved end of the rod to engage the loops.
2. The action required is a steady push and twist simultaneously. The fingers of the left hand are used to
bring the loops together just ahead of the hook on the end of the rod.
3. To remove, simply pull the rod out.
Kellems® Wire Management Products
Technical Information
Support Grips
Technical Information Kellems® Wire Management Products
T-45
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
Strain
Relief
Grip
Bus
Drop
Grips
Motor Box
Safety Spring
Strain
Relief
Grip
Bus Drop Grips and Safety Springs
Kellems Bus Drop Grips are offered with either a single eye or universal
bale attachment. The mesh is single weave galvanized steel with the
patented wide range construction. They are suitable for indoor use only.
Application
Bus Drop Grips provide a safe, easy and economical method to support
flexible cord or bus drop cable at bus duct and other industrial areas.
Benefits
• Easily installed.
• Absorb tension, vibration and pull with no cable damage.
• Patented mesh construction.
Safety Spring
Springs can be used with single eye grips by disassembling drawbar
from coil, placing through eye and replacing drawbar.
Kellems® Wire Management Products
Technical Information
Bus Drop Grips
T-46 Dimensions in Inches (cm)
www.hubbell-wiring.com
Conduit Riser Grips Kellems® Wire Management Products
Number of Cables in One Grip
Grip Dia. Range
2 3 4 5 6 and 7 8 9 Inches (cm)
.30-.38 .25-.31 .22-.27 .19-.24 .17-.22 .15-.19 .14-.18 .50-.61
(.76-.97) (.63-.79) (.56-.69) (.48-.61) (.43-.56) (.38-.48) (.36-.46) (1.27-1.55)
.38-.44 .31-.36 .27-.31 .24-.29 .22-.26 .19-.23 .18-.21 .62-.74
(.97-1.12) (.79-.91) (.69-.79) (.61-.74) (.56-.66) (.48-.58) (.46-.53) (1.57-1.88)
.44-.59 .36-.49 .31-.42 .29-.38 .26-.34 .23-.31 .21-.28 .75-.99
(1.12-1.50) (.91-1.24) (.79-1.07) (.74-.97) (.66-.86) (.58-.79) (.53-.71) (1.90-2.51)
.59-.75 .49-.63 .42-.54 .38-.48 .34-.43 .31-.39 .28-.35 1.00-1.24
(1.50-1.90) (1.24-1.60) (1.07-1.37) (.97-1.22) (.86-1.09) (.79-.99) (.71-.89) (2.54-3.15)
.75-.90 .63-.76 .54-.65 .48-.58 .43-.52 .39-.46 .35-.42 1.25-1.49
(1.90-2.29) (1.60-1.93) (1.37-1.65) (1.22-1.47) (1.09-1.32) (.99-1.17) (.89-1.07) (3.17-3.78)
.90-1.07 .76-.89 .65-.77 .58-.67 .52-.60 .46-.54 .42-.49 1.50-1.74
(2.29-2.72) (1.93-2.26) (1.65-1.96) (1.47-1.70) (1.32-1.52) (1.17-1.37) (1.07-1.24) (3.81-4.42)
1.07-1.22 .89-1.02 .77-.88 .67-.77 .60-.69 .54-.62 .49-.56 1.75-1.99
(2.72-3.10) (2.26-2.59) (1.96-2.24) (1.70-1.96) (1.52-1.75) (1.37-1.57) (1.24-1.42) (4.44-5.05)
1.22-1.53 1.02-1.28 .88-1.10 .77-.96 .69-.86 .62-.77 .56-.71 2.00-2.49
(3.10-3.89) (2.59-3.25) (2.24-2.79) (1.96-2.44) (1.75-2.18) (1.57-1.96) (1.42-1.80) (5.08-6.32)
1.53-1.83 1.28-1.53 1.10-1.32 .96-1.16 .86-1.03 .77-.93 .71-.85 2.50-2.99
(3.89-4.65) (3.25-3.89) (2.79-3.35) (2.44-2.95) (2.18-2.62) (1.96-2.36) (1.80-2.16) (6.35-7.59)
1.83-2.14 1.53-1.79 1.32-1.54 1.16-1.35 1.03-1.20 .93-1.08 .85-.99 3.00-3.49
(4.65-5.44) (3.89-4.55) (3.35-3.91) (2.95-3.43) (2.62-3.05) (2.36-2.74) (2.16-2.51) (7.62-8.86)
2.14-2.44 1.79-2.05 1.54-1.76 1.35-1.54 1.20-1.37 1.08-1.24 .99-1.13 3.50-3.99
(5.44-6.20) (4.55-5.21) (3.91-4.47) (3.43-3.91) (3.05-3.48) (2.74-3.15) (2.51-2.87) (8.89-10.13)
2.44-2.75 2.05-2.30 1.76-1.98 1.54-1.74 1.37-1.55 1.24-1.39 1.13-1.27 4.00-4.49
(6.20-6.98) (5.21-5.84) (4.47-5.03) (3.91-4.42) (3.48-3.94) (3.15-3.53) (2.87-3.23) (10.16-11.40)
2.75-3.06 2.30-2.56 1.98-2.20 1.74-1.93 1.55-1.72 1.39-1.55 1.27-1.41 4.50-4.99
(6.98-7.77) (5.84-6.50) (5.03-5.59) (4.42-4.90) (3.94-4.37) (3.53-3.94) (3.23-3.58) (11.43-12.67)
Note: * This chart is to be used for determining grip size when multiple cables are held in a single Support Grip. For Conduit Riser multiple cable selection,
see page T-47. It is always recommended that, when multiple cables are installed in a Support Grip, the tail end of the grip be banded after installation
on the cable bundle.
For Support Grips Only*
Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters
How to choose the correct grip size:
1. Find the Grip Circumference Range by measuring the circumference
of the bundle of different diameter cables to be gripped (see illustration).
2. Divide the bundle circumference by 3.14 to determine the diameter.
3. Choose a grip offering a range of cable diameters the same as the
cable diameter.
For Cables of Equal Diameters
Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .89" (2.26cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range, for a Split Grip
select the 1.75"-1.99" (4.44cm-5.05cm) range.
Kellems® Wire Management Products
Technical Information
Support Grips
T-47
Dimensions in Inches (cm) www.hubbell-wiring.com
Number of Equal Diameter Cables in One Grip
Grip Dia. Range
2 3 4 5 6 and 7 8 9 Inches (cm)
.29-.36 .24-.30 .21-.25 .18-.22 .16-.20 .15-.18 .14-.17 .50-.62
(.74-.91) (.61-.76) (.53-.63) (.46-.56) (.41-.51) (.38-.46) (.36-.43) (1.27-1.57)
.37-.43 .31-.36 .26-.30 .23-.27 .21-.24 .19-.22 .18-.20 .63-.74
(.94-1.09) (.79-.91) (.66-.76) (.58-.69) (.53-.61) (.48-.56) (.46-.51) (1.60-1.88)
.44-.58 .37-.48 .31-.41 .28-.36 .25-.32 .23-.29 .21-.27 .75-.99
(1.12-1.47) (.94-1.22) (.79-1.04) (.71-.91) (.63-.81) (.58-.74) (.53-.69) (1.90-2.51)
.59-.72 .49-.60 .42-.51 .37-.45 .33-.40 .30-.36 .28-.34 1.00-1.24
(1.50-1.83) (1.24-1.52) (1.07-1.30) (.94-1.14) (.84-1.02) (.76-.91) (.71-.86) (2.54-3.15)
.73-.87 .61-.72 .52-.61 .46-.54 .41-.48 .37-.43 .35-.40 1.25-1.49
(1.85-2.21) (1.55-1.83) (1.32-1.55) (1.17-1.37) (1.04-1.22) (.94-1.09) (.89-1.02) (3.17-3.78)
.88-1.01 .73-.85 .62-.71 .55-.63 .49-.56 .44-.51 .41-.47 1.50-1.74
(2.24-2.57) (1.85-2.16) (1.57-1.80) (1.40-1.60) (1.24-1.42) (1.12-1.30) (1.04-1.19) (3.81-4.42)
1.02-1.16 .86-.96 .72-.81 .64-.72 .57-.64 .52-.58 .48-.54 1.75-1.99
(2.59-2.95) (2.18-2.44) (1.83-2.06) (1.63-1.83) (1.45-1.63) (1.32-1.49) (1.22-1.37) (4.44-5.05)
1.17-1.44 .97-1.20 .82-1.02 .73-.90 .65-.80 .59-.72 .55-.67 2.00-2.49
(2.97-3.66) (2.46-3.05) (2.08-2.59) (1.85-2.29) (1.65-2.03) (1.50-1.83) (1.40-1.70) (5.08-6.32)
1.45-1.73 1.21-1.45 1.03-1.22 .91-1.08 .81-.96 .73-.87 .68-.81 2.50-2.99
(3.68-4.39) (3.07-3.68) (2.62-3.10) (2.31-2.74) (2.06-2.44) (1.85-2.21) (1.73-2.06) (6.35-7.59)
1.74-2.02 1.46-1.69 1.23-1.43 1.09-1.26 .97-1.11 .83-1.01 .82-.94 3.00-3.49
(4.42-5.13) (3.71-4.29) (3.12-3.63) (2.77-3.20) (2.46-2.82) (2.11-2.57) (2.08-2.39) (7.62-8.86)
2.03-2.31 1.70-1.93 1.44-1.63 1.27-1.44 1.12-1.27 1.02-1.15 .95-1.08 3.50-3.99
(5.16-5.87) (4.32-4.90) (3.66-4.14) (3.23-3.66) (2.84-3.23) (2.59-2.92) (2.41-2.74) (8.89-10.13)
Note: * This chart is to be used for determining grip size when multiple cables are held in a single Conduit Riser Grip. For Support Grip multiple cable selection,
see page T-46. It is always recommended that, when multiple cables are installed in a Conduit Riser Grip, the tail end of the grip be banded after
installation on the cable bundle.
Kellems® Wire Management Products
Technical Information
Conduit Riser Support Grips
For Conduit Riser Grips Only*
Multiple Cable Selection Charts for Cables and Wires of Unequal Diameters
How to choose the correct grip size:
1. Find the Grip Circumference Range by measuring the circumference
of the bundle of different diameter cables to be gripped (see illustration).
2. Divide the bundle circumference by 3.14 to determine the diameter.
3. Choose a grip offering a range of cable diameters the same as the
cable diameter.
For Cables of Equal Diameters
Under “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .85" (2.16cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range, for a Split Grip
select the 1.75"-1.99" (4.44cm-5.05cm) range.
Kellems® Wire Management Products Technical Information
T-48 Dimensions in Inches (cm)
www.hubbell-wiring.com
Technical Information Kellems® Wire Management Products
O.D.
I.D.
T
T
S
O.D.
I.D.
T
Conduit Ring Dimensions
Ring dimensions are found in the chart below. The ring material is
corrosion resistant. These rings will fit schedule 40 rigid PVC conduit
and standard electrical rigid metal conduit only.
Conduit Size O.D. I.D. S T
Inches Ring Number Inches (cm) Inches (cm) Inches (cm) Inches (cm)
¾ C-¾ .94" (2.39) .62" (1.57) — .19" (.48)
1 C-1 1.17" (2.97) .80" (2.03) — .19" (.48)
1¼ C-1¼ 1.50" (3.81) 1.03" (2.62) 1.31" (3.33) .16" (.41)
1½ C-1½ 1.76" (4.47) 1.23" (3.12) 1.52" (3.86) .16" (.41)
2 C-2 2.23" (5.66) 1.55" (3.94) 1.97" (5.00) .16" (.41)
2½ C-2½ 2.67" (6.78) 2.05" (5.21) 2.40" (6.10) .16" (.41)
3 C-3 3.20" (8.13) 2.55" (6.48) 2.97" (7.54) .22" (.56)
3½ C-3½ 3.80" (9.65) 3.05" (7.75) 3.47" (8.81) .22" (.56)
4 C-4 4.30" (10.92) 3.55" (9.02) 3.94" (10.01) .22" (.56)
4½ C-4½ 4.80" (12.19) 4.03" (10.24) 4.45" (11.30) .22" (.56)
5 C-5 5.30" (13.46) 4.46" (11.33) 4.96" (12.60) .22" (.56)
6 C-6 6.30" (16.00) 5.36" (13.61) 5.96" (15.14) .25" (.63)
Kellems® Wire Management Products
Conduit Riser Grips
Conduit Riser Support Grip-Ring Dimensions
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-41 through T-48.
Conduit Size ¾" and 1"
Conduit Size 1¼" to 6"
OPTISOK® Grip is a revolutionary tool to pull
preterminated fiber optic cables. They will protect
the connectors and guide the bundle through the
pulling environment
Pulling Grips are used for outside plant cable.
They are easy to install and remove, reusable,
and have a slim profile for small build up
Grips for cable support are easy to install or position.
They come in a closed style when the cable end is
available, and a split rod style for mid-span installation.
Will support the cable’s weight as it hangs in vertical,
sloping or horizontal position
T-49
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products
Fiber Optic Cable Grips
Pulling and Support Grips
Kellems® Wire Management Products Fiber Optic Cable Grips
T-50 Dimensions in Inches (cm)
www.hubbell-wiring.com
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-54 through T-57.
OPTISOK® Non-metallic Fiber Optic Pulling Tool For Preterminated,
Inside Plant Fiber Optic Cables and Bundles of Twisted Pair
OPTISOK® Non-Metallic Fiber Optic Pulling Tool
Bundle/Size Approx. O/A Ring Ring Maximum
Range Length O.D. Thickness Work Load Catalog
Inches (cm) Inches (cm) Inches (cm) Inches (cm) lbs. (N) Number
.125"-.562" (.318-1.427) 28" (71.12) .71" (1.803) .10" (.254) 30 (133) CCPS1
.250"-.750" (.635-1.905) 31" (78.74) .71" (1.803) .10" (.254) 40 (178) CCPS2
.750"-1.750" (1.905-4.445) 33" (83.82) 1.57" (3.988) .16" (.406) 50 (222) CCPS3
Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel
Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel
Diameter Mesh Eye Eye Lug Maximum
Range Length Length Diameter Diameter Breaking Strength Catalog
Inches (cm) Inches (cm) Inches (cm) Inches (cm) Inches (cm) lbs. (N) Number
.312"-.625" (.79-1.59) 22.5" (57.15) 6.3" (16.00) .20" (.51) .51" (1.30) 3,000 (13,344) PFOLT312
Kellems® Wire Management Products
Fiber Optic Cable Pulling Grips
Special Purpose
Fiber Optic Cable Pulling Grips Kellems® Wire Management Products
T-51
Dimensions in Inches (cm) www.hubbell-wiring.com
F-O Pulling Grip, Flexible Eye
Approx.
Cable Breaking E M D
Diameter Range Strength Approx. Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Inches (cm) Number
.10"-.22" (.25-.56) 1,000 (4,448) 5.5" (14) 9" (23) 0.8" (2) 033291000
.21"-.35" (.53-.89) 1,500 (6,672) 5.5" (14) 14" (36) 0.8" (2) 033291001
.32"-.48" (.81-1.22) 2,200 (9,786) 6.0" (15) 18" (46) 0.9" (2.29) 033291002
.42"-.61" (1.07-1.55) 2,800 (12,454) 6.0" (15) 21" (53) 0.9" (2.29) 033291003
.53"-.74" (1.35-1.88) 3,300 (14,678) 6.5" (17) 24" (61) 1.3" (3.30) 033291004
.64"-.87" (1.63-2.21) 4,700 (20,906) 6.5" (17) 27" (69) 1.3" (3.30) 033291005
F-O Pulling Grip, Swivel Eye
Approx.
Cable Breaking E M D
Diameter Range Strength Approx. Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Inches (cm) Number
.21"-.35" (.53-.89) 1,500 (6,672) 4.0" (10.16) 14" (35.56) 0.9" (2.29) 033291008
.32"-.48" (.81-1.22) 2,200 (9,786) 4.0" (10.16) 18" (45.72) 0.9" (2.29) 033291009
.42"-.61" (1.07-1.55) 2,800 (12,454) 4.0" (10.16) 21" (53.34) 0.9" (2.29) 033291010
.53"-.74" (1.35-1.88) 3,300 (14,678) 4.5" (11.43) 24" (60.96) 1.3" (3.30) 033291011
.64"-.87" (1.63-2.21) 4,700 (20,906) 4.5" (11.43) 27" (68.58) 1.3" (3.30) 033291012
Note: E-Eye length.
M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Fiber Optic Cable Pulling Grips
Double/Single Weave Mesh, Galvanized Steel, for Outside Plant Cable
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-54 through T-57.
Kellems® Wire Management Products Fiber Optic Cable Pulling Grips
T-52 Dimensions in Inches (cm)
www.hubbell-wiring.com
F-O Pulling Grip, Flexible Eye, Low Profile, Double/Single Weave Mesh
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Number
.10"-.22 (.25-.56) 900 (4,003) 7.5" (19) 10" (25) 033291193
.21"-.35" (.53-.89) 1,400 (6,227) 7.5" (19) 14" (36) 033291194
.32"-.48" (.81-1.22) 2,000 (8,896) 8.5" (22) 19" (48) 033291195
.42"-.61" (1.07-1.55) 2,500 (11,120) 8.5" (22) 21" (53) 033291196
.53"-.74" (1.35-1.88) 3,000 (13,344) 8.5" (22) 23" (58) 033291197
.64"-.87" (1.63-2.21) 4,200 (18,682) 8.5" (22) 25" (64) 033291198
.75"-1.00" (1.90-2.54) 4,200 (18,682) 8.5" (22) 28" (71) 033291199
F-O Slack Pulling Grip, Split Mesh Rod Closing, Single Weave
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Number
.25"-.37" (.63-.94) 300 (1,334) 3" (7.6) 4.7" (12) 033291015
.38"-.49" (.97-1.24) 800 (3,558) 3" (7.6) 5" (13) 033291016
.50"-.61" (1.27-1.55) 800 (3,558) 3" (7.6) 7.5" (19) 033291017
.62"-.74" (1.57-1.88) 1,200 (5,338) 3" (7.6) 8" (20) 033291018
Note: E-Eye length.
M-Mesh length at nominal diameter.
Kellems® Wire Management Products
Fiber Optic Cable Pulling Grips
Galvanized Steel for Outside Plant Cable
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-54 through T-57.
Fiber Optic Cable Pulling Grips Kellems® Wire Management Products
Single Eye, Closed Mesh,
Single Weave
Single Eye, Split Mesh,
Rod Closing, Single Weave
T-53
Dimensions in Inches (cm) www.hubbell-wiring.com
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-54 through T-57.
For permanent support
when cable end is available
to be installed through grip.
For support when cable end
not available.
Kellems® Wire Management Products
Fiber Optic Cable Support Grips
Single Weave, Tin-Coated Bronze
F-O
Single Eye Cable Support Grip, Closed Mesh, Single Weave
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Number
.18"-.25" (.46-.63) 300 (1,334) 3" (7.6) 1.7" (4.3) 022291000
.23"-.32" (.58-.81) 300 (1,334) 3" (7.6) 2.5" (6.4) 022291001
.30"-.39" (.76-.99) 300 (1,334) 4" (10) 2.5" (6.4) 022291002
.37"-.48" (.94-1.22) 300 (1,334) 5" (13) 4" (10) 022291003
.46"-.58" (1.17-1.47) 400 (1,779) 6" (15) 4" (10) 022291004
.56"-.71" (1.42-1.80) 600 (2,669) 7" (18) 5.5" (14) 022291005
.69"-.88" (1.75-2.24) 800 (3,558) 8" (20) 6" (15) 022291006
F-O
Single Eye Cable Support Grip, Split Mesh, Rod Closing,
Single Weave
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Number
.18"-.25" (.46-.63) 300 (1,334) 3" (7.6) 2.5" (6.4) 022291016
.23"-.32" (.58-.81) 300 (1,334) 3" (7.6) 2.5" (6.4) 022291017
.30"-.39" (.76-.99) 300 (1,334) 4" (10) 2.5" (6.4) 022291018
.37"-.48" (.94-1.22) 300 (1,334) 5" (13) 4" (10) 022291019
.46"-.58" (1.17-1.47) 400 (1,779) 6" (15) 5" (13) 022291020
.56"-.71" (1.42-1.80) 600 (2,669) 7" (18) 5" (13) 022291021
.69"-.88" (1.75-2.24) 800 (3,558) 8" (20) 6" (15) 022291022
Note: E-Eye length.
M-Mesh length at nominal diameter.
Kellems® Wire Management Products Fiber Optic Cable Support Grips
T-54 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems has wide experience with grips for the new
technology of fiber optic cable. As the industry leader in
producing wire mesh grips for the stringent requirements
of fiber optic applications, Kellems has developed several
series of grips for use with fiber optic communications cable.
These grips include pulling grips with built in swivels, grips
with steel ends to protect fragile cable ends, grips with low
profiles to pull cables in tight places and the OPTISOK® an
effective tool to place preterminated cables. Also available
are grips to support fiber optic cable.
Select the Correct Fiber Optic Grip
Each Kellems grip is designed to work on a specific range of
cable diameters.
Step 1 Determine your cable outside diameter.
Step 2 Find the grip size that encompasses your cable diameter.
Step 3 Whenever possible, use a closed mesh that assembles
over the cable end. If the cable end is not available, use
a split mesh.
Step 4 Where available, select an eye style that suits your needs.
Step 5 Estimate the tension to be put on the grip, establish the
working load you require and compare this to the listed
approximate breaking strength of the grip to insure that
the grip will be strong enough.
Kellems® Wire Management Products
Technical Information
Fiber Optic Pulling and Support Grips
Examples
Approx. Breaking Safety Max. Rec. Catalog
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Number
Pulling Grips 2,500 (11,120) 5 500 (2,224) 033291196
Support Grips 400 (1,779) 10 40 (178) 022291004
The maximum recommended working load is the tension to be exerted on the grip in application with a margin of safety to take care of
unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable to for the application.
Fiber Optic Grip Materials
Material Features Product Group
Galvanized steel wire • High strength • Pulling grips
• Not subject to continuous outside environment
Tin-coated bronze wire • Corrosion resistant for normal outside areas • Support grips
• Non-magnetic
• Moderate strength
Non-metallic braid • Superior flex life • OPTISOK®
• Non-conductive
• Corrosion resistant
• Moderate strength
Approvals
CSA Certification is indicated on appropriate product catalog pages.
Technical Information Kellems® Wire Management Products
The broad application of Kellems grips on a wide variety
of objects requires that adequate safety factors be used to
establish working loads. The approximate breaking strength
of a Kellems grip represents an average calculation based
on data established from actual direct tension testing done
in our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are
never the same. The tension, diameter, movement, number
of objects gripped, gripping surface, and the attachments
used are just some of the factors which vary with each
application. These factors, together with the effects of
abrasion, corrosion, prior use or abuse and any other
variables of a specific application, must be considered by
the user and the grip replaced as appropriate. Where the
conditions of the application are not well defined or known
or where risk of injury to persons or property is involved, a
greater safety factor should be utilized.
Under normal conditions, Kellems’ recommended factor
of safety is five for catalog listed pulling grips, and ten
for catalog listed support grips.
Any warranty as to quality, performance or fitness for
use of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored, handled,
used, maintained and inspected by the user at a frequency
appropriate for the use and condition of the grip.
For grip applications on materials other than those that
the grips have been specifically designed for, consult the
factory.
Safety And Working Load Factors For Wire Mesh Grips
T-55
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems offers a unique and simple to use tool
for the installation of preconnectorized fiber optic
cables, jumpers and bundles of twisted pair
communication cables - the OPTISOK®.
The OPTISOK® is a highly flexible and expandable
nonmetallic sleeve open on one end and with a
pulling ring on the other. It will expand to enclose
the larger group of fiber optic connectors and grab
the cable below the connector bundle by wrapping
and taping to provide a gripping tool that will grab
the cable(s) below the connectors. The pulling ring
can be attached to a pulling line or fish tape and the
OPTISOK® will act as the pulling tool.
OPTISOK® will contain and protect the connector
bundle and save time and labor by making the
pulling job easier, protecting the connectors from
possible damage during the pull and facilitating the
passage of the connector bundle through cramped
and tight spaces. The OPTISOK® can be used to
pull cables through plenums, underfloor duct, office
partitions, raised access floors and conduits. Three
sizes are available for all applications.
How to Select OPTISOK®
• Identify connector bundle diameter to be inserted into
the OPTISOK®.
• Choose appropriate catalog number based on size range.
Installation Information
Step 1. Expand open end of OPTISOK® and gently work in fiber
optic connector bundle.
Step 2. Still gently, work connector bundle up to the forward
section of the OPTISOK®.
Step 3. Starting at approximately 6" (15.2cm) from tail end of
OPTISOK®, tightly fold over the OPTISOK® around cables
and tape wrapped section 3" (7.62cm) past tail end onto
the bundle.
Step 4. Securely attach pulling line or tape to pulling ring.
Note To remove OPTISOK® carefully unwrap tape and slide out cables and
connectors or cut OPTISOK® away without damaging connectors
or cables.
1
2
3
4
Kellems® Wire Management Products
Technical Information
OPTISOK® Pulling Grips
Kellems® Wire Management Products Technical Information
T-56 Dimensions in Inches (cm)
www.hubbell-wiring.com
Pulling Grip for Loose Tube Fiber Optic Cable
Kellems offers a wire mesh specifically designed to pull loose tube fiber optic cable and meet the special
pulling requirements recommended by fiber optic cable manufacturers.
Many fiber optic cable manufacturers require special cable preparation prior to pulling where a short section
of the outer jacket is stripped off exposing the aramid strength member. This creates two cable diameters,
one including the jacket and a second smaller diameter at the strength member. Kellems fiber grip with its
special weave will accommodate and securely grab both diameters, at the outside jacket and the internal
aramid strength member.
Additionally, this galvanized steel mesh grip has longer leads at the pulling eye to facilitate pulling the cable
up through the top, a very low profile lug and eye to slip through tight areas, and short shoulders to protect
the cable while maintaining the slim profile.
The grip can be used to pull cable overhead as well as underground through conduit and duct. It easily mates
with a swivel and has the necessary strength to securely make pulls.
Application Information
• Prior to pulling cable, follow cable manufacturers’ cable preparation recommendations.
• Never exceed cable manufacturers’ pulling tension recommendations.
• Never use grips to approximate breaking strength safety factor of 5 recommended.
Pulling Grips for Other Outside Plant Cables,
Swivel Eye, Flexible Eye, Split Style, Low Profile
Kellems Pulling Grips for fiber optic cable are made of high strength galvanized steel strand. They feature
a multiweave mesh, with one-half the mesh length double weave, and the second half single weave. This
special weave provides positive holding power while allowing the grip to remain flexible with no damage to
the cable jacket. Added features include a steel nose cone which protects the cable end and allows the grip
to pass easily through conduit and enclosures. The eye connects easily to a swivel or a pulling line. Several
grip sizes are available to accommodate all diameters of fiber optic cable.
Application
Kellems Flexible Eye Pulling Grips for fiber optic cable are used for the installation of fiber optic
communication lines either underground, overhead, through conduit or through enclosures. They will fit
single cables or cable bundles, are easily installed on the cable, and are reusable.
Benefits
• High strength multiweave mesh for positive holding power.
• Highly flexible mesh to follow the pulling path of the cable.
• Steel nose cone reduces snags and hang-ups and protects cable end.
• Easily installed and removed.
• A dependable, reusable pulling tool.
Kellems® Wire Management Products
Technical Information
Fiber Optic Pulling Grips
Technical Information Kellems® Wire Management Products
T-57
Dimensions in Inches (cm) www.hubbell-wiring.com
Support Grips for Fiber Optic Cable
Kellems Support Grips for fiber optic cable are specially designed to hold the cable weight as it hangs in a
vertical or horizontal position. Fiber optic cable must be supported and Kellems Grips provide the support
easily and economically.
These grips are made of high grade, non-magnetic tin-coated bronze strand. They are offered in universal
bale or single eye configurations and are available in either closed mesh (for use where the cable end is
available) or in split mesh, rod closing (for installation on existing cable runs or at specific locations).
Split Support Grip Rod Closing Instructions
The stainless steel rod is a precise built-in feature which makes threading easy and fast. The strands of the
mesh pass around the rod and match up with the strands from the opposite direction. The rod does not
touch the cable at any point and therefore cannot cut the cable. Rod Closing Grips are reusable. They may
be removed and reused as many times as desired.
Fast to Install
Step 1. Wrap the grip around the cable and thread the rod through the preformed loops with a corkscrew
motion, using the curved end of the rod to engage the loops.
Step 2. The action required is a steady push and twist simultaneously. The fingers of the left hand are used
to bring the loops together just ahead of the hook on the end of the rod.
Step 3. To remove, simply pull the rod out.
Kellems® Wire Management Products
Technical Information
Fiber Optic Support Grips
Kellems® Wire Management Products Technical Information
T-58 Dimensions in Inches (cm)
www.hubbell-wiring.com
WARNING!
It is important that you read all breaking strength,
safety and technical data relating to this product
on pages T-42 through T-43.
Types of Attachment
The five attachment methods shown below provide
unlimited flexibility of attachment to meet any
condition.
Type E
Double Eye Grip, used where fastening is made with
eyebolts or similar anchor terminations.
Type A
Single Eye Grip, used where fastening MUST be made
from one point.
Type U
Universal Bale Grip, used to fasten around a structure or
closed eye.
Type Y
Threaded bolt (⁵⁄₁₆-18 x 1½" long), used to fasten through
drilled holes in plate.
Type F
Split fitting to fit AN-818 nuts. Fitting is positioned over
nut and located with internal flange. A hose clamp is
furnished and required to hold the fitting in correct
position.
Note: It should be emphasized that Kellems® Hose Containment Grips are not to be used as a pressure reinforcing device for hose systems. These grips are
custom made. Consult Technical Services for details.
Kellems Hose Containment Grips are used on high pressure, flexible hose lines to prevent the hose from whipping
violently in the event of hose failure at the fitting. These grips will prevent serious injury to personnel and damage
to equipment by holding the hose in place in the event of hose failure.
Kellems patented Hose Containment Grips are made of stainless steel with double weave mesh construction for
high strength and come complete with hose clamps.
Kellems Hose Containment Grips are supplied in diameters, length and attachments to meet individual requirements.
Contact the Wiring Device-Kellems factory for specific information. These grips help meet OSHA Federal Register
1926-302 (b), 1926-603 (9), (10), JIC H-1-1973 (H13.11) and JIC P-1-1975 (P11.34) requirements.
Hose Containment Grips Kellems® Wire Management Products
Kellems® Wire Management Products
Hose Containment Grips
Endless weave provides easy cable/exible conduit installation
Stainless steel mesh is corrosion resistant. Can be used inside or
outside. It eliminates cable or exible conduit pull out and reduces
costly downtime
Multiweave grip gives cable arc-of-bend control minimizing cable
damage and extending cable life. It is the strongest strain relief
device available. Meets and exceeds all code requirements;
prevents cable/conduit pull-out
A liquidtight tting is available with both cable and conduit ttings;
prevents liquids from running through the tting into the enclosure
An N.P.T. and PG threaded body allows easy attachment to either threaded
hub or knock-out in box
T-59
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products
Strain Relief for Flexible Cords
For Insulated Cables and Flexible, Liquidtight Conduits
Kellems® Wire Management Products Strain Relief for Flexible Cords
Straight Male
T-60 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems® Wire Management Products
Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
Deluxe Cord Grips Kellems® Wire Management Products
Straight Male Thread
N.P.T. Thread
Size Inches
Grip Diameter Range
Inches (cm)
Form
Size
Catalog Number
³⁄₈
.250"-.312"
.312"-.375"
.375"-.437"
(.63-.79)
(.79-.95)
(.95-1.11)
F1
07401001
07401002
07401003
½
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
07401004
07401006
07401008
07401010
½.625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 074011247*
074011248*
¾
.187"-.250"
.250"-.375"
.375"-.500"
.500"-.625"
(.47-.63)
(.63-.95)
(.95-1.27)
(1.27-1.59)
F2
07401011
07401013
07401015
07401017
¾.625"-.750"
.750"-.875"
(1.59-1.90)
(1.90-2.22) F3 07401018
074011249*
1
.375"-.500"
.500"-.625"
.625"-.750"
.750"-.875"
.875"-1.000"
1.000"-1.125"
(.95-1.27)
(1.27-1.59)
(1.59-1.90)
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
F4
074011195
07401019
07401021
07401023
07401025
074011250*
11.125"-1.250"
1.250"-1.375"
(2.86-3.17)
(3.17-3.49) F5 074011028*
074011029*
1¼
.750"-.875"
.875"-1.000"
1.000"-1.125"
1.125"-1.250"
1.250"-1.375"
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
(2.86-3.17)
(3.17-3.49)
F5
074011251
07401026
07401027
07401028
074011178*
1½
.750"-.875"
.875"-1.000"
1.000"-1.125"
1.125"-1.250"
1.250"-1.375"
(1.90-2.22)
(2.22-2.54)
(2.54-2.86)
(2.86-3.17)
(3.17-3.49)
F5
074011252
07401029
07401030
07401031
07401032
1½
1.312"-1.437"
1.437"-1.562"
1.562"-1.687"
1.687"- 1.812"
1.750"-1.875"
(3.33-3.65)
(3.65-3.97)
(3.97-4.28)
(4.28-4.60)
(4.44-4.76)
F6
074011253
074011254*
074011255*
074011256*
074011257*
2
1.250"-1.375"
1.312"-1.437"
1.437"-1.562"
1.562"-1.687"
1.687"-1.812"
1.750"- 1.875"
(3.17-3.49)
(3.33-3.65)
(3.65-3.97)
(3.97-4.28)
(4.28-4.60)
(4.44-4.76)
F6
074011258
074011259
07401033
07401034
07401035
074011260
2
1.812"-1.937"
1.937"-2.062"
2.062"-2.187"
2.187"-2.312"
2.312"-2.437"
(4.60-4.92)
(4.92-5.24)
(5.24-5.55)
(5.55-5.87)
(5.87-6.19)
F7
074011261
074011262*
074011263*
074011264*
074011265*
2½
1.688"-1.812"
1.812"-1.937"
1.937"-2.062"
2.062"-2.187"
2.187"-2.312"
2.312"-2.437"
(4.29-4.60)
(4.60-4.92)
(4.92-5.24)
(5.24-5.55)
(5.55-5.87)
(5.87-6.19)
F7
074011030
074011031
074011032
074011033
074011034
074011266*
3
1.937"-2.062"
2.062"-2.187"
2.187"-2.312"
2.312"-2.437"
(4.92-5.24)
(5.24-5.55)
(5.55-5.87)
(5.87-6.19)
F7
074011036
074011037
074011038
074011039
3
2.437"-2.625"
2.625"-2.812"
2.812"-3.000"
3.000"-3.250"
(6.19-6.67)
(6.67-7.14)
(7.14-7.62)
(7.62-8.25)
F8
074011186
074011187
074011188
074011189*
Note: Kellems® Deluxe Cord Grips are suitable
for use in hazardous locations per Class I
Div. 2, Class II Div. 1 & 2, Class III Div. 1 &
2 of the National Electric Code Sections
501.10(b)(2), 502.10(a)(2), 502.10(b)(2),
503.10(a)(2) and 503.10(b).
* Cable jacket may have to be stripped to
pass through connector body.
45º Male
Straight Female
90º Male
T-61
Dimensions in Inches (cm) www.hubbell-wiring.com
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
Kellems® Wire Management Products
Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Straight Female Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
½ .375"-.500" (.95-1.27) F2 07401043
.500"-.625" (1.27-1.59) 07401045
¾ .500"-.625" (1.27-1.59) F2 07401052
¾ .625"-.750" (1.59-1.90) F4 07401053
90° Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
.250"-.312" (.63-.79) 07401071
³⁄₈ .312"-.375" (.79-.95) F1 07401072
.375"-.437" (.95-1.11) 07401073
.187"-.250" (.47-.63) 07401074
½ .250"-.375" (.63-.95) F2 07401076
.375"-.500" (.95-1.27) 07401078
.500"-.625" (1.27-1.59) 07401080*
.375"-.500" (.95-1.27) 07401081
¾ .500"-.625" (1.27-1.59) F3 07401083
.625"-.750" (1.59-1.90) 07401084*
.750"-.875" (1.90-2.22) 074011275*
.500"-.625" (1.27-1.59) 07401085
.625"-.750" (1.59-1.90) 07401087
1 .750"-.875" (1.90-2.22) F4 07401089
.875"-1.000" (2.22-2.54) 07401091*
1.000"-1.125" (2.54-2.86) 074011229*
.750"-.875" (1.90-2.22) 074011230
1¼ .875"-1.000" (2.22-2.54) F5 07401137
1.000"-1.125" (2.54-2.86) 07401108
1.125"-1.250" (2.86-3.17) 074011042*
1.000"-1.125" (2.54-2.86) 074011045
1½ 1.125"-1.250" (2.86-3.17) F5 074011046
1.250"-1.375" (3.17-3.49) 074011047
1.312"-1.437" (3.33-3.65) 074011233
2 1.437"-1.562" (3.65-3.97) F6 074011244
1.687"-1.812" (4.28-4.60) 074011246
1.750"-1.875" (4.44-4.76) 074011234*
45° Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
.250"-.375" (.63-.95) 074011236
½ .375"-.500" (.95-1.27) F2 074011021
.500"-.625" (1.27-1.59) 074011237*
.500"-.625" (1.27-1.59) 074011049
¾ .625"-.750" (1.59-1.90) F3 074011051*
.750"-.875" (1.90-2.22) 074011239*
.625"-.750" (1.59-1.90) 074011055
1 .750"-.875" (1.90-2.22) F4 074011057
.875"-1.000" (2.22-2.54) 074011199*
1¼ 1.000"-1.125" (2.54-2.86) F5 074011059
1.125"-1.250" (2.86-3.17) 074011060
Kellems® Wire Management Products Deluxe Cord GrIps
Note: Kellems® Deluxe Cord Grips are suitable
for use in hazardous locations per Class I
Div. 2, Class II Div. 1 & 2, Class III Div. 1 &
2 of the National Electric Code Sections
501.10(b)(2), 502.10(a)(2), 502.10(b)(2),
503.10(a)(2) and 503.10(b).
* Cable jacket may have to be stripped to
pass through connector body.
Straight Male
90º Male
T-62 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems® Wire Management Products
Deluxe Cord Grips
Nylon Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Straight Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
.187"-.250" (.47-.63) 074011331
½ .250"-.375" (.63-.95) F2 074011332
.375"-.500" (.95-1.27) 074011333
.500"-.625" (1.27-1.59) 074011334*
.375"-.500" (.95-1.27) 074011335
¾ .500"-.625" (1.27-1.59) F3 074011336
.625"-.750" (1.59-1.90) 074011337
.750"-.875" (1.90-2.22) 074011338*
.625"-.750" (1.59-1.90) 074011341
1 .750"-.875" (1.90-2.22) F4 074011342
.875"-1.000" (2.22-2.54) 074011343
1.000"-1.125" (2.54-2.86) 074011344*
90° Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
.250"-.375" (.63-.95) 074011346
½ .375"-.500" (.95-1.27) F2 074011347
.500"-.625" (1.27-1.59) 074011348*
.375"-.500" (.95-1.27) 074011349
¾ .500"-.625" (1.27-1.59) F3 074011350
.625"-.750" (1.59-1.90) 074011351*
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
Deluxe Cord Grips Kellems® Wire Management Products
Note: Kellems® Deluxe Cord Grips are suitable
for use in hazardous locations per Class I
Div. 2, Class II Div. 1 & 2, Class III Div. 1 &
2 of the National Electric Code Sections
501.10(b)(2), 502.10(a)(2), 502.10(b)(2),
503.10(a)(2) and 503.10(b).
* Cable jacket may have to be stripped to
pass through connector body.
Straight Stainless Steel Male
90º Male
Straight Male
T-63
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products
Deluxe Cord Grips
Nylon Fittings, Non-metallic Mesh, Liquidtight, for Insulated Cables and
Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Nylon Fittings Non-metallic Mesh, Liquidtight for Insulated Cables
Straight Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
.187"-.250" (.47-.63) CG304NM
³⁄₈ .250"-.312" (.63-.79) F1 CG305NM
.312"-.375" (.79-.95) CG306NM
.187"-.250" (.47-.63) CG404NM
½ .250"-.375" (.63-.95) F2 CG406NM
.375"-.500" (.95-1.27) CG408NM
.375"-.500" (.95-1.27) CG608NM
¾ .500"-.625" (1.27-1.59) F3 CG610NM
.625"-.750" (1.59-1.90) CG612NM
.500"-.625" (1.27-1.59) CG810NM
1 .625"-.750" (1.59-1.90) F4 CG812NM
.750"-.875" (1.90-2.22) CG814NM
.875"-1.000" (2.22-2.54) CG816NM
90° Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
½ .250"-.375" (.63-.95) F2 CG40690NM
.375"-.500" (.95-1.27) CG40890NM
.375"-.500" (.95-1.27) CG60890NM
¾ .500"-.625" (1.27-1.59) F3 CG61090NM
.625"-.750" (1.59-1.90) CG61290NM*
1 .625"-.750" (1.59-1.90) F4 CG81290NM
.750"-.875" (1.90-2.22) CG81490NM
Stainless Steel Fittings, Stainless Steel Mesh,
Liquidtight for Insulated Cables
Straight Male Thread
N.P.T. Thread Grip Diameter Range Form
Size Inches Inches (cm) Size Catalog Number
.187"-.250" (.47-.63) CG404SST
½ .250"-.375" (.63-.95) F2 CG406SST
.375"-.500" (.95-1.27) CG408SST
.500"-.625" (1.27-1.59) CG410SST
¾ .375"-.500" (.95-1.27) F2 CG608SST
.500"-.625" (1.27-1.59) CG610SST
¾ .625"-.750" (1.59-1.90) F3 CG612SST
.750"-.875" (1.90-2.22) CG614SST
.500"-.625" (1.27-1.59) CG810SST
1 .625"-.750" (1.59-1.90) F4 CG812SST
.750"-.875" (1.90-2.22) CG814SST
.875"-1.000" (2.22-2.54) CG816SST
WARNING! It is important that
you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
Kellems® Wire Management Products Deluxe Cord GrIps
Note: Kellems® Deluxe Cord Grips are suitable
for use in hazardous locations per Class I
Div. 2, Class II Div. 1 & 2, Class III Div. 1 &
2 of the National Electric Code Sections
501.10(b)(2), 502.10(a)(2), 502.10(b)(2),
503.10(a)(2) and 503.10(b).
* Cable jacket may have to be stripped to
pass through connector body.
Straight PG Male
Straight Metric Male
T-64 Dimensions in Inches (cm)
www.hubbell-wiring.com
Straight PG* Male Thread
Cord Diameter Range
Hub Size Inches (cm) Form Size Catalog Number
PG16 .500"-.625" (1.27-1.59) F2 074PG16010
PG21 .500"-.625" (1.27-1.59) F2 074PG21010
PG21 .625"-.750" (1.59-1.90) F3 074PG211247
.750"-.875" (1.90-2.22) 074PG211248
.625"-.750" (1.59-1.90) 074PG29021
PG29 .750"-.875" (1.90-2.22) F4 074PG29023
.875"-1.000" (2.22-2.54) 074PG29025
PG29 1.125"-1.250" (2.86-3.17) F5 074PG291028**
PG36 1.125"-1.250" (2.86-3.17) F5 074PG36028**
Note: * Panzergewinde.
Straight Metric Male Thread
Cord Diameter Range
Hub Size Inches (cm) Form Size Catalog Number
M20 .500"-.625" (1.27-1.59) F2 074M20010
M25 .625"-.750" (1.59-1.90) F3 074M251247
.750"-.875" (1.90-2.22) 074M251248
M25 .500"-.625" (1.27-1.59) F2 074M25017
.625"-.750" (1.59-1.90) 074M32021
M32 .750"-.875" (1.90-2.22) F4 074M32023
.875"-1.000" (2.24-2.54) 074M32025
M32 1.125"-1.250" (2.86-3.17) F5 074M321028
1.000"-1.125" (2.54-2.86) 074M321250
Specifications
Material Temperature Range
Aluminum –30°F to +240°F (–34°C to +115°C).
Stainless Steel (Gotcha Rings) –30°F to +240°F (–34°C to +115°C).
Neoprene (Bushings) –30°F to +240°F (–34°C to +115°C).
Hazardous Locations Suitable for use in hazardous locations per Class I Div. 2,
Class II Div. 1 & 2, Class III Div. 1 & 2 N.E.C.
Reference 501.10(b)(2), 502.10(a)(2), 502.10(b)(2), 503.10(a)(2)
and 503.10(b).
Approvals
Cord Connectors UL Listed in accordance with Standard 514B.
Deluxe Cord Grips UL Control numbers 898D and 899D.
Wet Locations Suitable for use in wet locations when used with a listed
nylon washer between box and fitting.
Kellems® Wire Management Products
PG and Metric Threaded Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
WARNING! It is important that
you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
PG and Metric Threaded Deluxe Cord Grips Kellems® Wire Management Products
Note: Kellems® Deluxe Cord Grips are suitable
for use in hazardous locations per Class I
Div. 2, Class II Div. 1 & 2, Class III Div. 1 &
2 of the National Electric Code Sections
501.10(b)(2), 502.10(a)(2), 502.10(b)(2),
503.10(a)(2) and 503.10(b).
** Cable jacket may have to be stripped to
pass through connector body.
T-65
Dimensions in Inches (cm) www.hubbell-wiring.com
Insulated
Non-Insulated
Non-Insulated, Wide Range Strain Relief
Cable Mesh Length
Thread Diameter Range @ Nom. Dia. Catalog
Size Inches (cm) Inches (cm) Number
½ N.P.T. .24"-.32" (.61-.81) 3.25" (8.25) 073031200
½ N.P.T. .32"-.43" (.81-1.09) 3.75" (9.52) 073031201
½ N.P.T. .43"-.54" (1.09-1.37) 4.75" (12.06) 073031202
¾ N.P.T. .54"-.73" (1.37-1.85) 6.5" (16.51) 073031203
1 N.P.T. .73"-.97" (1.85-2.46) 7" (17.78) 073031204
1¼ N.P.T. .97"-1.25" (2.46-3.17) 9" (22.86) 073031205
PG29* .73"-.97" (1.85-2.46) 7" (17.78) 073PG291204
Note: * Panzergewinde.
Insulated, Wide Range Strain Relief with Insulating Bushing
Min. Space
Cable Mesh Length Between
Thread Diameter Range @ Nom. Dia. Dim. A Grips Catalog
Size Inches (cm) Inches (cm) In. (cm) In. (cm) Number
½ N.P.S. .24"-.32" (.61-.81) 3.25" (8.25) 1" (2.54) 1.25" (3.17) 073031206
½ N.P.S. .32"-.43" (.81-1.09) 3.75" (9.52) 1" (2.54) 1.25" (3.17) 073031207
½ N.P.S. .43"-.54" (1.09-1.37) 4.75" (12.06) 1" (2.54) 1.25" (3.17) 073031208
¾ N.P.S. .54"-.73" (1.37-1.85) 6.5" (16.51) 1" (2.54) 1.5" (3.81) 073031209
1 N.P.S. .73"-.97" (1.85-2.46) 7" (17.78) 1.313" (3.02) 1.75" (4.44) 073031210
1¼ N.P.S. .97"-1.25" (2.46-3.17) 9" (22.86) 1.313" (3.02) 2.25" (5.71) 073031211
1½ N.P.T. 1.25"-1.50" (3.17-3.81) 11.75" (29.84) 1.313" (3.02) 2.5" (6.35) 073031212
2 N.P.T. 1.50"-1.70" (3.81-4.32) 13.25" (33.65) 1.375" (3.49) 3.25" (8.25) 073031213
2½ N.P.T. 1.70"-2.00" (4.32-5.08) 13.5" (34.29) 1.5" (3.81) 3.625" (9.21) 073031214
2½ N.P.T. 2.00"-2.45" (5.08-6.22) 13.75" (34.92) 1.5" (3.81) 3.625" (9.21) 073031215
Kellems® Wire Management Products
Dust-Tight Strain Relief Grips
Aluminum Fittings, Galvanized Steel Mesh, for Insulated Cables
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
Kellems® Wire Management Products Dust-Tight Strain Relief Grips
T-66 Dimensions in Inches (cm)
www.hubbell-wiring.com
Application
Kellems® I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip® plugs and
connector bodies. The eye tabs fit under the nylon cord clamp and the
screws slide through the eyelets, securing the grip in place.
These grips are for indoor use only.
Benefits
• Easily attached to Insulgrip plugs and connector bodies.
• Controls cable arc-of-bend.
• Provides heavy-duty strain relief.
• Fits all sizes.
I-Grips
Cable Diameter Range E M
Inches (cm) Inches (cm) Inches (cm) Catalog Number
.32"-.43" (.81-1.09) 1.25" (3.17) 4" (10.16) 07310001
.43"-.56" (1.09-1.42) 1.25" (3.17) 4.75" (12.06) 07310002
.56"-.73" (1.42-1.85) 1.50" (3.81) 6" (15.24) 07310003
.73"-.85" (1.85-2.16) 1.50" (3.81) 6.5" (16.51) 07310004
.85"-1.00" (2.16-2.54) 1.50" (3.81) 8" (20.32) 07310005
1.00"-1.25" (2.54-3.17) 1.50" (3.81) 10" (25.40) 07310006
Note: E-Eye length.
M-Mesh length at nominal diameter.
Eyelet hole diameter .203" (.52cm).
I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof covers
are to be installed.
Kellems® Wire Management Products
I-Grips
Plastic-Coated, Galvanized Steel Mesh for Insulated Cables
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-71 through T-76.
I-Grips Kellems® Wire Management Products
T-67
Dimensions in Inches (cm) www.hubbell-wiring.com
Thread Adapters for Multi-Pin Connectors
Kellems® Thread Adapters are devices formatting
AN-MS connectors and other multi-pin connectors
to Kellems grips with N.P.T. threaded fittings. They
are made of aluminum with internal threads and
replace the connector cord clamp. These adapters
permit the installation of Kellems Grips, to prevent
cable or conduit pull-out and control arc-of-bend.
Applications
Thread adapters allow the installation of Kellems®
Grips on multi-pin connectors at electrical consoles,
mobile equipment, control switches, assembly
equipment and testing machines.
Benefits
• Easy installation.
• Allows the use of Kellems grips.
• Extends connector and cable life.
Kellems® Wire Management Products
Thread Adapters for Multi-Pin Connectors
Aluminum
Kellems® Wire Management Products Thread Adapters for Multi-Pin Connectors
Thread Adapters for Multi-Pin Connectors
Liquidtight
Conduit Grips
Thread Adapters Deluxe Cord Grips Strain Relief Grips (Insulated Throat)
AN-MS AN-MS N.P.T.
Connector Cable Clamp Thread Thread Catalog Cable Diameter Catalog Cable Diameter Catalog Catalog
Size** Number*** Size A in. Size B in. Number Range Inches (cm) Number Range Inches (cm) Number Number
8S, 10S 3057-3 ½" x 28" 091041000 .250"-.312" (.63-.79) 07401001
10SL, 12, 12S 3057-4 ⁵⁄₈" x 24" ³⁄₈ 091041001 .312"-.375" (.79-.95) 07401002
14, 14S 3057-6 ¾" x 20" 091041002 .375"-.437" (.95-1.11) 07401003
14, 14S 3057-6 ¾" x 20" 091041003 .187"-.250" (.47-.63 07401004 .24"-.32" (.61-.81) 073031200 —
16, 16S 3057-8 ⁷⁄₈" x 20" ½ 091041004 .250"-.375" (.63-.95) 07401006 .32"-.43" (.81-1.09) 073031201 074093512
18 3057-10 1" x 20" 091041006 .375"-.500" (.95-1.27) 07401008 .43"-.54" (1.09-1.37) 073031202 —
.500"-.625" (1.27-1.59) 07401010*
16, 16S 3057-8 ⁷⁄₈" x 20" 091041005 .187"-.250" (.47-.63) 07401011
18 3057-10 1" x 20" ¾ 091041007 .250"-.375" (.63-.95) 07401013
20, 22 3057-12 1³⁄₁₆" x 18" 091041008 .375"-.500" (.95-1.27) 07401015 .54"-.74" (1.37-1.85) 073031203 074093513
.500"-.625" (1.27-1.59) 07401017
.625"-.750" (1.59-1.90) 07401018
20, 22 3057-12 1³⁄₁₆" x 18" 091041009 .375"-.500" (.95-1.27) 074011195
24, 28 3057-16 1⁷⁄₁₆" x 18" 091041010 .500"-.625" (1.27-1.59) 07401019
32 3057-20 1¾" x 18" 1 091041012 .625"-.750" (1.59-1.90) 07401021 .73"-.97" (1.85-2.46) 073031204 074093514
36 3057-24 2" x 18" 091041015 .750"-.875" (1.90-2.22) 07401023
.875"-1.000" (2.22-2.54) 07401025
24, 28 3057-16 1⁷⁄₁₆" x 18" 091041011 .750"-.875" (1.90-2.22) 074011251
32 3057-20 1¾" x 18" 1¼ 091041013 .875"-1.000" (2.22-2.54) 07401026
36 3057-24 2" x 18" 091041016 1.000"-1.125" (2.54-2.86) 07401027 .97"-1.25" (2.46-3.17) 073031205 074093515
1.125"-1.375" (2.86-3.17) 07401028
32 3057-20 1¾" x 18" 091041014 .875"-1.000" (2.22-2.54) 07401029
36 3057-24 2" x 18" 1½ 091041017 1.000"-1.125" (2.54-2.86) 07401030 — 074093516
40 3057-28 2¼" x 16" 091041019 1.125"-1.250" (2.86-3.17) 07401031
1.250"-1.375" (3.17-3.49) 07401032
Note: * Cable jacket may have to be stripped to pass through connector body.
** Number stamped on connector shell.
*** Number stamped on clamp shell.
Example Thread Adapter
091041006
90° Angle with Male Fitting
Straight with Male Fitting
T-68 Dimensions in Inches (cm)
www.hubbell-wiring.com
Benefits
• Helps prevent conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
Straight With Male Fitting
Conduit N.P.T.
Trade Size Fitting Size Mesh Length Catalog Number Catalog Number
Inches Inches Inches (cm) (Insulated) (Non-insulated)
³⁄₈ ½ 3" (7.62) 074093511 074093401
½ ½ 3.5" (8.89) 074093512 074093402
¾ ¾ 4" (10.16) 074093513 074093403
1 1 5" (12.70) 074093514 074093404
1¼ 1¼ 6" (15.24) 074093515 074093405
1½ 1½ 6.75" (17.14) 074093516 074093406
2 2 8" (20.32) 074093518 074093408
2½ 2½ 9.75" (24.76) 074093520 074093410
3 3 11" (27.94) 074093522 074093412
4 4 14" (35.56) 074093526 —
90° Angle With Male Fitting
Conduit N.P.T.
Trade Size Fitting Size Mesh Length Catalog Number Catalog Number
Inches Inches Inches (cm) (Insulated) (Non-insulated)
³⁄₈ ½ 3" (7.62) 074093541 074093421
½ ½ 3.5" (8.89) 074093542 074093422
¾ ¾ 4" (10.16) 074093543 074093423
1 1 5" (12.70) 074093544 074093424
1¼ 1¼ 6" (15.24) 074093545 074093425
1½ 1½ 6.75" (17.14) 074093546 074093426
2 2 8" (20.32) 074093548 074093428
2½ 2½ 9.75" (24.76) 074093550 —
3 3 11" (27.94) 074093552 —
Note: For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-77, T-79 and T-80.
Strain Relief for Liquidtight Conduit Kellems® Wire Management Products
Kellems® Wire Management Products
Strain Relief for Liquidtight Conduit
Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit
and PolyTuff I Non-Metallic Conduit
Straight with Chase Connector
45° Angle with Male Fitting
T-69
Dimensions in Inches (cm) www.hubbell-wiring.com
Straight With Chase Fitting
Conduit N.P.T.
Trade Size Fitting Size Mesh Length
Inches Inches Inches (cm) Catalog Number
½ ½ 3.5" (8.89) 07406079
¾ ¾ 4" (10.16) 07406080
1 1 5" (12.70) 07406081
1¼ 1¼ 6" (15.24) 07406082
1½ 1½ 6.75" (17.14) 07406083
45° Angle With Male Fitting
Conduit N.P.T.
Trade Size Fitting Size Mesh Length Catalog Number Catalog Number
Inches Inches Inches (cm) (Insulated) (Non-insulated)
³⁄₈ ½ 3" (7.62) 074093561 074093441
½ ½ 3.5" (8.89) 074093562 074093442
¾ ¾ 4" (10.16) 074093563 074093443
1 1 5" (12.70) 074093564 074093444
1¼ 1¼ 6" (15.24) 074093565 074093445
1½ 1½ 6.75" (17.14) 074093566 074093446
2 2 8" (20.32) 074093568 074093448
Note: For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-77, T-79 and T-80.
Kellems® Wire Management Products Strain Relief for Liquidtight Conduit
Kellems® Wire Management Products
Strain Relief for Liquidtight Conduit
Steel Fitting, Stainless Steel Mesh for Liquidtight Metal Conduit
and PolyTuff I Non-Metallic Conduit
T-70 Dimensions in Inches (cm)
www.hubbell-wiring.com
Straight Male with Fitting
90° Angle
Straight Male Hubbell Fitting
Conduit N.P.T.
Trade Size Fitting Size Mesh Length
Inches Inches Inches (cm) Catalog Number
³⁄₈ ½ 3.75" (9.52) H038CNK
½ ½ 4.5" (11.43) H050CNK
¾ ¾ 6.25" (15.87) H075CNK
1 1 7.5" (19.05) H100CNK
1¼ 1¼ 9" (22.86) H125CNK
1½ 1½ 13.5" (34.29) H150CNK
2 2 14.5" (36.83) H200CNK
90° Male Hubbell Fitting
Conduit N.P.T.
Trade Size Fitting Size Mesh Length
Inches Inches Inches (cm) Catalog Number
³⁄₈ ½ 3.75" (9.52) H0389CNK
½ ½ 4.5" (11.43) H0509CNK
¾ ¾ 6.25" (15.87) H0759CNK
1 1 7.5" (19.05) H1009CNK
1¼ 1¼ 9" (22.86) H1259CNK
1½ 1½ 13.5" (34.29) H1509CNK
2 2 14.5" (36.83) H2009CNK
WARNING!
It is important that you read
all breaking strength, safety
and technical data relating
to this product on pages
T-78 through T-80.
Strain Relief for Liquidtight Conduit Kellems® Wire Management Products
Kellems® Wire Management Products
Strain Relief for Liquidtight Conduit
Steel Fitting, Stainless Steel Mesh for UL Type A Liquidtight Conduit
T-71
Dimensions in Inches (cm) www.hubbell-wiring.com
Strain Relief System Selection Chart
Cord or Conduit Type Fitting or Page
Grip Type Application Features Range Inches (cm) Attachment Number
Deluxe Cord Outdoors or indoors where Aluminum fittings, .187"-3.250" N.P.T., PG, and metric T-60, T-61,
Aluminum subjected to moisture or stainless steel mesh, (.47-8.25) aluminum, male straight, T-64
Fitting/ splash. Examples are crane neoprene oil-and- 45° male, 90° male,
Stainless and hoist pendant drop watertight bushing. female straight.
Steel Grip stations, hand tools, pumps Double-single weave. Thread sizes ³⁄₈"-3".
and processing equipment.
Deluxe Cord Outdoors or indoors where Nylon fitting, stainless .187"-1.125" N.P.T. nylon, T-62
Nylon Fitting/ subjected to moisture or steel mesh, double-single (.47-2.86) male straight,
Stainless splash. Examples are weave, neoprene oil-and- 90° male. Thread
Steel Grip marine and food watertight bushing. sizes ½"-1".
processing equipment.
Deluxe Cord Indoor or outdoors. Non-metallic grip is .187"-1.000" N.P.T. nylon, straight male, T-63
Nylon Fitting/ Provides liquidtight seal, corrosion resistant, (.47-2.54) thread sizes ³⁄₈"-1" 90° male,
Non-metallic where exposed to moisture. nonconductive and thread sizes ½"-1".
Grip Excellent for oil refining provides superior grip-
and chemical processing. ping and flexing benefits.
Neoprene liquidtight
bushing. Nylon fitting.
Deluxe Cord Indoor or outdoor use where Stainless steel fitting .187"-1.000" Straight male T-63
Stainless exposed to moisture. Very and grip for strength. (.47-2.54) Only with N.P.T.
Steel Fitting strong for heavy abuse areas Neoprene liquidtight Thread sizes ½"-1".
And Grip such as drilling platforms, bushing. Double/single
steel mills and mines. weave grip.
Dust-Tight Indoor use only for wiring Neoprene gasket–seals .240"-2.450" Straight male N.P.S. T-65
Strain Relief of electrical enclosures, out chips, dirt, dust. (.61-6.22) or N.P.T.
machine tools, portable One piece design with
power tools, bus drop galvanized steel mesh.
cable systems. Insulating bushing available.
Zinc-plated steel locknut.
Liquidtight Wiring of machine tools, Stainless steel mesh, .375"-4.000" N.P.T. ½"-4", T-68, T-69
Flexible electrical enclosures, motors liquidtight fittings. trade sizes Hubbell fittings,
Conduit Grip and systems where metallic Sealing “O" rings Male straight,
(Metal and liquidtight flexible conduit (optional). Choice of 45° male, 90° male,
Non-Metallic) is subjected to vibration, fittings. female straight.
flexure, motion or strain.
Liquidtight Wiring or machine tools, Stainless steel mesh, .375"-2.008" N.P
.T. steel, T-70
Flexible electrical enclosures, liquidtight fittings with trade size male Hubbell fittings,
Conduit Grip motors and systems “O" ring and locknut. straight male, 90°
(UL Type A) where conduit is subject Thread sizes ½"-2".
to vibration and strain.
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Kellems Strain Relief Grips are designed to prevent tension
from being transmitted to joints and terminals on electrical
cord, cable and conduit. In most applications, a Kellems
grip for strain relief is stronger than the cable itself and
gives much greater security than the use of a fitting alone.
Kellems Grips for strain relief help make electrical systems
safer, and save money by minimizing downtime from
costly electrical failure due to cable pull-out. Kellems Grips
also aid in compliance with the National Electric Code’s
terminal tension protection requirements.
Select the Correct Grip for Strain Relief
Kellems Grips for strain relief are designed to fit on
electrical cord, cable or flexible conduit.
Step 1 Refer to the chart below to determine the
grip style best suited for your application.
Step 2 Determine your cable outside diameter or
conduit size.
Step 3 Locate environment—indoors or outdoors.
Step 4 Decide if a liquidtight seal is required.
Step 5 Select N.P.T. size and fitting style.
Kellems® Wire Management Products Technical Information
T-72 Dimensions in Inches (cm)
www.hubbell-wiring.com
Wire Mesh Grip Materials
Material Features Product Group
Galvanized steel wire • High strength • Strain relief grips
• Not subject to continuous outside environment • I-Grips
Stainless steel wire (302/304) • High strength • Deluxe cord grips
• Corrosion resistant • Liquidtight, flexible, metal conduit grips
• Slightly magnetic • UL type A conduit grips
Non-metallic strand • Superior flex life • Non-metallic deluxe cord grips
• Non-conductive
• Corrosion resistant
• Moderate strength
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Operating Temperatures
Material Temperature Range
Aluminum –40°F to +300°F (–40°C to +149°C).
Aluminum Deluxe Cord Grips –30°F to +240°F (–34°C to +115°C).
Non-Metallic Deluxe Cord Grips –30°F to +225°F (–34°C to +107°C).
Nylon –40°F to +225°F (–40°C to +107°C).
Nylon Fitting with Stainless Steel Mesh –40°F to +225°F (–40°C to +107°C).
Stainless Steel –60°F to +1000°F (–51°C to +537°C).
Stainless Steel Deluxe Cord Grips –30°F to +240°F (–34°C to +115°C).
Neoprene (Bushings) –30°F to +240°F (–34°C to +115°C).
Hazardous Locations
Product Categories
The product categories listed to the right are suitable Deluxe cord grip, aluminum fitting;
for use in hazardous locations per Class I Div. 2, Deluxe cord grip, nylon fitting;
Class II Div. 1 & 2, Class III Div. 1 & 2. Deluxe cord grip, non-metallic;
Sealtite conduit grips;
Dustight strain relief grips.
Flammability
Non-metallic deluxe cord grips will not support combustion. Listed below are the ratings.
Component Rating
Mesh grip UL 94HB.
Fitting UL 94V-2.
Approvals
UL Listing and CSA Certification are indicated on appropriate product catalog pages.
Agency UL Control Number
Underwriters Laboratories Inc. 898D and 899D.
Wet Locations
Product Categories
The products noted to the right are suitable Deluxe cord grip, aluminum fitting;
for use in wet locations when a listed sealing Deluxe sealing ring cord grip;
ring is used between box and fitting. Deluxe cord grip, non-metallic;
Sealtite conduit grips;
Hubbell non-metallic conduit grips;
Cord connectors;
Hubbell Juniors;
PolyTuff® connectors;
Hubbell sealtite conduit connectors.
Technical Information Kellems® Wire Management Products
T-73
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Kellems® Wire Management Products Technical Information
Form Size Definition
The term “Form Size” refers to the physical mass or overall dimensions of a cord connector. Form 1 is the
smallest size, Form 8 is the largest size.
Knockout Holes
N.P.T.
Hub Size Knockout Hole Recommended
Inches Min. to Max. Inches (cm)
¼ .540" to .570" (1.37-1.45)
³⁄₈ .671" to .701" (1.70-1.78)
½ .859" to .906" (2.18-2.30)
¾ 1.094" to 1.141" (2.78-2.90)
1 1.359" to 1.406" (3.45-3.57)
1¼ 1.719" to 1.766" (4.37-4.49)
1½ 1.969" to 2.016" (5.00-5.12)
2 2.453" to 2.500" (6.23-6.35)
2½ 2.953" to 3.000" (7.50-7.62)
3 3.578" to 3.625" (9.09-9.21)
Product Data
Deluxe Cord Grips, Liquidtight for Insulated Cables
Deluxe Cord Grips helps to alleviate pull tension on terminals, control cable arc-of-bend, prevent cord pull-
out, and provide a liquidtight seal. They are offered with either aluminum, stainless steel or nylon fittings in
a variety of configurations and N.P.T. thread sizes. Additionally, a completely non-metallic product is offered
on page T-63.
Application
Deluxe Cord Grips are used indoors or outdoors to help prevent cord pull-out, and where cables are
subjected to moisture, splash or submersion. Specific uses are: wiring enclosures, pendant stations,
hand tools, construction, processing and material handling equipment, pumps, motors and machine tools.
Benefits
• Helps to prevent cable pull-out.
• Controls cable arc-of-bend.
• Provides a liquidtight seal.
• Corrosion resistant stainless steel mesh with aluminum collar.
A
(Overall)
B Ref.
C
D
F
E
T-74 Dimensions in Inches (cm)
www.hubbell-wiring.com
Deluxe Cord Grips Fitting Dimensions
Straight Hubbell Connectors
Aluminum, Inches (cm) Nylon, Inches (cm) Stainless Steel, Inches (cm)
F A B C D E A B C D E A B C D E
N.P.T. Throat Throat Throat
(Inches) Form Dia. Ref. Dia. A/C* A/F* Dia. Ref. Dia. A/C* A/F* A/C* A/F Dia. A/C* A/F*
³⁄₈-18 1 .88" .90" .46" .44" .99" .88" 1.00" 1.10" .43" .45" 1.00" .93" 1.01" .88" .90" .46" .45" .87" .75"
(2.24) (2.29) (1.17) (1.12) (2.51) (2.24) (2.54) (2.79) (1.09) (1.14) (2.54) (2.36) (2.57) (2.24) (2.29) (1.17) (1.14) (2.21) (1.90)
½-14 1 .88" .90" .46" .44" 1.00" .88" 1.00" 1.10" .46" .45" 1.00" .93" — — — — — — —
(2.24) (2.29) (1.17) (1.12) (2.54) (2.24) (2.54) (2.79) (1.17) (1.14) (2.54) (2.36)
½-14 2 1.13" 1.10" .55" .64" 1.11" 1.00" 1.32" 1.50" .53" .58" 1.25" 1.12" 1.30" 1.13" 1.10" .54" .63" 1.16" 1.00"
(2.87) (2.79) (1.40) (1.63) (2.82) (2.54) (3.35) (3.81) (1.35) (1.47) (3.17) (2.84) (3.30) (2.87) (2.79) (1.37) (1.60) (2.95) (2.54)
½-14 3 1.38" 1.50" .55" .64" 1.40" 1.25" — — — — — — — — — — — — —
(3.51) (3.81) (1.40) (1.63) (3.56) (3.17)
¾-14 2 1.13" 1.10" .55" .64" 1.29" 1.13" — — — — — — — — — — — — —
(2.87) (2.79) (1.40) (1.63) (3.28) (2.87)
¾-14 3 1.38" 1.50" .55" .82" 1.40" 1.25" 1.56" 1.60" .55" .77" 1.44" 1.31" 1.59" 1.38" 1.30" .56" .81" 1.44" 1.25"
(3.51) (3.81) (1.40) (2.08) (3.56) (3.17) (3.96) (4.06) (1.40) (1.96) (3.66) (3.33) (4.04) (3.51) (3.30) (1.42) (2.06) (3.66) (3.17)
1-11½ 3 — — — — — — — — — — — — — — — — — — —
1-11½ 4 1.75" 1.60" .71" 1.02" 1.81" 1.62" 1.88" 1.75" .70" 1.01" 1.84" 1.63" 2.02" 1.75" 1.40" .70" 1.03" 1.88" 1.63"
(4.44) (4.06) (1.80) (2.59) (4.60) (4.11) (4.78) (4.44) (1.78) (2.57) (4.67) (4.14) (5.13) (4.44) (3.56) (1.78) (2.62) (4.78) (4.14)
1-11½ 5 2.31" 1.70" .66" 1.01" 2.28" 2.00" — — — — — — — — — — — — —
(5.87) (4.32) (1.68) (2.57) (5.79) (5.08)
1¼-11½ 5 2.31" 1.70" .74" 1.26" 2.28" 2.12" — — — — — — — — — — — — —
(5.87) (4.32) (1.88) (3.20) (5.79) (5.38)
1½-11 5 2.31" 1.70" .74" 1.38" 2.28" 2.12" — — — — — — — — — — — — —
(5.87) (4.32) (1.88) (3.51) (5.79) (5.38)
1½-11½ 6 3.00" 2.20" .75" 1.50" 2.97" 2.75" — — — — — — — — — — — — —
(7.62) (5.59) (1.90) (3.81) (7.54) (6.98)
2-11½ 6 3.00" 2.20" .80" 1.92" 3.24" 3.00" — — — — — — — — — — — — —
(7.62) (5.59) (2.03) (4.88) (8.24) (7.62)
2-11½ 7 3.85" 2.70" .88" 1.94" 4.05" 3.75" — — — — — — — — — — — — —
(9.78) (6.86) (2.24) (4.93) (10.29) (9.52)
2½-8 7 3.85" 2.70" 1.30" 2.32" 4.34" 4.02" — — — — — — — — — — — — —
(9.78) (6.86) (3.30) (5.89) (11.02) (10.21)
2½-8 8 4.75" 2.70" 1.25" 2.38" 4.86" 4.50" — — — — — — — — — — — — —
(12.06) (6.86) (3.17) (6.05) (12.34) (11.43)
3-8 7 3.85" 2.70" 1.30" 2.54" 4.34" 4.01" — — — — — — — — — — — — —
(9.78) (6.86) (3.30) (6.45) (11.02) (10.21)
3-8 8 4.50" 2.70" 1.38" 3.00" 4.86" 4.50" — — — — — — — — — — — — —
(11.43) (6.86) (3.51) (7.62) (12.34) (11.43)
Note: *A/C— Across Corners; A/F—Across Flats.
Dimensions shown are approximate and
are subject to change without notice.
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Technical Information Kellems® Wire Management Products
B Ref.
A
Ref.
D
C
G
B Ref.
A
D
C
E
F
G
T-75
Dimensions in Inches (cm) www.hubbell-wiring.com
Deluxe Cord Grips Fitting Dimensions
45° Hubbell Connectors
Aluminum, Inches (cm)
F A B C D E G
N.P.T. Throat Across Across
(Inches) Form Ref Ref Dia. Comers Flats Dia.
½-14 2 2.00" 1.90" .550" .560" 1.270" 1.110" 1.125"
(5.08) (4.83) (1.40) (1.42) (3.23) (2.79) (2.86)
¾-14 3 2.30" 2.50" .560" .750" 1.480" 1.281" 1.375"
(5.84) (6.53) (1.42) (1.90) (3.76) (3.25) (3.49)
1-11½ 4 2.60" 2.80" .700" 1.000" 1.690" 1.500" 1.750"
(6.60) (7.11) (1.78) (2.54) (4.29) (3.81) (4.44)
1¼-11½ 5 3.90" 3.90" .740" 1.250" 2.45" 2.125" 2.310"
(9.91) (9.91) (1.88) (3.17) (6.22) (5.40) (5.87)
1½-11½ 5 3.90" 3.90" .740" 1.500" 2.45" 2.125" 2.310"
(9.91) (9.91) (1.88) (3.81) (6.22) (5.40) (5.87)
90° Hubbell Connectors
Aluminum, Inches (cm) Nylon, Inches (cm)
F A B C D E G A B C D E G
N.P.T. Throat Throat
(Inches) Form Ref Dia. A/C* A/F* Dia. Ref Dia. A/C* A/F Dia.
³⁄₈-18 1 1.27" 2.00" .460" .440" 1.15" 1.10" .875" — — — — — — —
(3.23) (5.08) (1.17) (1.12) (2.92) (2.79) (2.22)
½-14 2 1.56" 2.30" .500" .546" 1.30" 1.13" 1.125" 1.41" 2.50" .550" .575" 1.23" 1.12" 1.315"
(3.96) (5.84) (1.27) (1.39) (3.30) (2.87) (2.86) (3.58) (6.35) (1.40) (1.46) (3.12) (2.82) (3.34)
¾-14 3 1.79" 2.80" .560" .765" 1.49" 1.31" 1.375" 1.65" 2.81" .560" .765" 1.42" 1.29" 1.560"
(4.55) (7.11) (1.42) (1.94) (3.78) (3.33) (3.49) (4.19) (7.14) (1.42) (1.94) (3.61) (3.28) (3.96)
1-11½ 4 2.08" 3.20" .700" 1.000" 1.70" 1.50" 1.750" 1.99" 3.30" .700" 1.010" 1.82" 1.60" 1.875"
(5.28) (8.13) (1.78) (2.54) (4.32) (3.81) (4.44) (5.05) (8.38) (1.78) (2.57) (4.62) (4.06) (4.76)
1¼-11½ 5 3.18" 4.30" .730" 1.260" 2.47" 2.15" 2.310" — — — — — — —
(8.08) (10.92) (1.85) (3.20) (6.27) (5.46) (5.87)
1½-11½ 5 3.18" 4.30" .750" 1.500" 2.47" 2.15" 2.310" — — — — — — —
(8.08) (10.92) (1.92) (3.81) (6.27) (5.46) (5.87)
2-11½ 6 3.51" 5.50" .800" 1.920" 2.98" 2.78" 3.000" — — — — — — —
(8.92) (13.97) (2.03) (4.88) (7.57) (7.06) (7.62)
Note: *A/C - Across Corners; A/F - Across Flats.
Dimensions shown are approximate and
are subject to change without notice.
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Kellems® Wire Management Products Technical Information
A
(Overall)
B Ref.
C (N.P.T. Thread Depth)
D
E
F
T-76 Dimensions in Inches (cm)
www.hubbell-wiring.com
Deluxe Cord Grips Fitting Dimensions
Female Hubbell Connectors
Aluminum Inches (cm)
F A B C D E
Throat Across Across
N.P.T. Form Dia. Ref Dia. Corners Flats
³⁄₈-18 1 .88" 1.40" .560" .44" .94" .81"
(2.24) (3.56) (1.42) (1.12) (2.39) (2.06)
½-14 2 1.13" 1.80" .560" .63" 1.15" 1.00"
(2.87) (4.57) (1.42) (1.60) (2.92) (2.54)
¾-14 2 1.13" 2.10" .750" .63" 1.44" 1.25"
(2.87) (5.33) (1.90) (1.60) (3.66) (3.17)
1-11½ 4 1.75" 2.30" .880" 1.10" 1.88" 1.63"
(4.44) (5.84) (2.24) (2.79) (4.78) (4.14)
1¼-11½ 5 2.31" 2.80" .950" 1.43" 2.64" 2.29"
(5.87) (7.11) (2.41) (3.63) (6.71) (5.82)
1½-11½ 5 2.31" 2.80" .950" 1.43" 2.64" 2.29"
(5.87) (7.11) (2.41) (3.63) (6.71) (5.82)
Product Data
Dust-Tight Strain Relief Grips for Insulated Cables
Kellems Strain Relief Grips connect flexible cord or bus drop cable to electrical
enclosures. For indoor use only, they are available with either insulated or non-
insulated aluminum fittings, and feature single weave, galvanized steel mesh grips
with patented wide range mesh construction. They come with a locknut and a
neoprene gasket that provides a dust tight seal.
Application
Used to connect electrical cable to power boxes, cabinets, panel boards, power
centers, machine tools and with bus drop systems.
Benefits
• Helps prevent cord or cable pull-out. • Patented mesh construction.
• Provides a dust tight seal. • One piece design.
• Easy installation.
I-Grips for Insulated Cables
Kellems I-Grips are made of high strength, plastic coated galvanized steel strand.
They are offered in six sizes to fit all cable diameters used with Hubbell Insulgrip®
Kellems l-Grips will control cable arc-of-bend and reduce high pull tensions from
being transmitted to the wiring terminals.
Application
Kellems I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip plugs and connector
bodies. The eye tabs fit under the nylon cord clamp and the screws slide through the
eyelets, securing the grip in place.
I-Grips can be used on any Insulgrip cord set which requires cable, arc-of-bend
control or heavy duty strain relief. Cord sets used at in-door construction sites or for
plant maintenance jobs are examples.
These grips are for indoor use only.
Benefits
• Easily attached to Insulgrip plugs • Provides heavy duty strain relief.
and connector bodies. • Controls cable arc-of-bend.
• Fits all sizes.
Note: I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof covers are to be installed.
Kellems® Wire Management Products
Technical Information
Strain Relief Grips
Technical Information Kellems® Wire Management Products
Dimensions shown are approximate and
are subject to change without notice.
T-77
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
Strain Relief Grips for Liquidtight Flexible Metal and PolyTuff I Non-Metallic Conduit
Kellems Liquidtight, Flexible Metal Conduit Grips are offered with high quality Hubbell plated steel fittings in a wide
variety of N.P.T. sizes and configurations, either insulated or non-insulated. The addition of a stainless steel mesh to
these fittings makes them stronger than the conduit itself. Kellems Conduit Grips helps prevent conduit pull-out from
the connecting fitting that is subject to stress, pull tension, vibration, motion or strain. They promote safe electrical
systems and reduce equipment downtime.
Application
Kellems Conduit Grips are used in the wiring of machine tools, motors, molding equipment, transformers, weaving
and paper machines, fans, lighting, bakeries, breweries, food processing, chemical plants, dairies, mines and any
application that requires Liquidtight Conduit.
Benefits
• Helps prevent conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
• Liquidtight fittings.
• Easily installed.
• Stainless steel grip resists corrosion.
Kellems Conduit Grips are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2,
Class III Div. 1 & 2 of the National Electric Code.
Hardened Steel Locknut
has tangs that dig into box
for excellent continuity of
ground; locknut will not slip
or spin
Connectors with insulated throats protect
insulation on wires during wire pulling.
Yellow color easily seen by inspectors.
2½" - 4" sizes include insulating bushing
instead of xed insulator
Steel grounding ferrule easily
threaded by hand. Fits convolutions
to conduit. Eliminates pullouts and
insures continuity of ground;
distortion free to remain reusable
Nylon gland ring is split for ease of installation
and greater compression. Reversible design
cannot be installed facing the wrong way.
Nylon is impervious to liquids, resistant to
temperature extremes and resists abrasion
Hexagonal compression
nut is screw machined steel
through 1" and malleable
iron on larger sizes
Optional Sealing Washer gives
better liquidtight protection
around knockout of sheet metal
box. Neoprene gasket seals out
liquids and steel retaining ring
protects gasket from distortion;
order separately
Body is virtually unbreakable.
Straight connectors through 1" are
screw machine steel; other sizes
malleable iron. Threads at left are
tapered to insure liquidtight seal in
threaded hub. Liquidtight conduit
cutaway view shows exible steel
core under plastic jacket
Wire mesh grip
prevents pullout
Liquidtight conduit cutaway
view shows exible steel core
under plastic jacket
T-78 Dimensions in Inches (cm)
www.hubbell-wiring.com
Steel Locknut has tangs that dig
into box for excellent continuity of
ground; locknut will not slip or spin
Insulated throat protects
insulation on wires during
pulling; yellow color easily
seen by inspectors
Body is virtually unbreakable. Straight connectors through
1" are screw machine steel; other sizes are malleable iron.
Threads are tapered to insure liquidtight seal when used in
threaded hub; octagonal shape inside holds the ferrule to
prevent conduit from twisting during installation
Neoprene O-ring is factory
assembled into the body
to seal out liquids
Wire mesh grip
prevents pullout
Yellow nylon ferrule ts inside non-
metallic conduit to hold the shape;
barb in designed to assure liquidtight
seal even with non-square cut;
ferrule is keyed to t into body to
prevent conduit twisting
Hexagonal compression nut is machine
steel through 1" malleable iron on larger
sizes; tapered interior compresses
sleeve over conduit sealing out liquids
and preventing pullout
Yellow nylon sleeve installs over
conduit; six slits in sleeve permit
tight compression onto conduit
as compression nut is tightened
Strain Relief for UL Type A, Flexible, Liquidtight Conduit
Kellems Grips for UL Type A, non-metallic, flexible, liquidtight conduit are available in straight and 90° male and feature
a high quality Hubbell plated steel or malleable iron fitting, complete with a sealing O-ring, lock nut and stainless steel
mesh. These grips increase the retention of the conduit in the fitting, control its arc-of-bend and provide a liquidtight seal.
Application
These grips are used on UL Type A non-metallic conduit connections at limit switches, motor boxes, panel boards,
control stations and on all types of machinery and machine tools.
Benefits
• Provides a liquidtight seal.
• Helps prevent conduit pull-out.
• Reduces conduit cutting, kinking, fraying and splitting at the fitting.
• Easily installed.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
T-79
Dimensions in Inches (cm) www.hubbell-wiring.com
Liquidtight Conduit Grip Fitting Dimensions-Inches
Straight with Male Fitting
Dimensions
D
Trade A B C Throat E Catalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Number
³⁄₈ 1.43" .59" 1.20" 1.06" .61" 1.07" .93" 074093401
½ 1.43" .59" 1.34" 1.19" .61" 1.22" 1.06" 074093402
¾ 1.56" .59" 1.55" 1.37" .84" 1.43" 1.25" 074093403
1 1.68" .66" 1.95" 1.69" 1.06" 1.73" 1.56" 074093404
1¼ 2.03" .63" 2.39" 2.06" 1.37" 2.36" 2.08" 074093405
1½ 2.21" .63" 2.72" 2.38" 1.53" 2.79" 2.48" 074093406
2 2.28" .69" 3.08" 2.87" 2.06" 3.32" 2.90" 074093408
Straight with Male Fitting with Insulated Throat
Dimensions
D
Trade A B C Throat E Catalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Number
³⁄₈ 1.50" .66" 1.20" 1.06" .57" 1.07" .93" 074093511
½ 1.50" .66" 1.34" 1.19" .57" 1.22" 1.06" 074093512
¾ 1.62" .66" 1.55" 1.38" .78" 1.43" 1.25" 074093513
1 1.75" .72" 1.95" 1.69" .98" 1.73" 1.56" 074093514
1¼ 2.09" .69" 2.39" 2.06" 1.29" 2.36" 2.08" 074093515
1½ 2.28" .69" 2.72" 2.37" 1.53" 2.79" 2.48" 074093516
2 2.34" .75" 3.08" 2.87" 1.95" 3.32" 2.90" 074093518
2½ 3.56" 1.06" 3.92" 3.62" 2.42" 3.85" 3.60" 074093520
3 3.81" 1.06" 4.70" 4.31" 3.01" 4.65" 4.33" 074093522
4 3.81" 1.06" 5.75" 5.31" 3.96" 5.75" 5.39" 074093526
45° Angle with Male Fitting
Dimensions
M
Trade H J K L Throat N Catalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Number
³⁄₈ 1.19" 1.28" .59" 1.20" 1.06" .60" 1.16" 1.02" 074093441
½ 1.19" 1.28" .59" 1.34" 1.19" .61" 1.21" 1.06" 074093442
¾ 1.19" 1.43" .59" 1.55" 1.45" .84" 1.50" 1.32" 074093443
1 1.38" 1.53" .66" 1.95" 1.69" 1.05" 1.82" 1.59" 074093444
1¼ 1.42" 1.69" .63" 2.39" 2.06" 1.37" 2.32" 2.03" 074093445
1½ 1.66" 2.00" .66" 2.72" 2.38" 1.60" 2.62" 2.29" 074093446
2 1.69" 2.25" .66" 3.08" 2.88" 2.05" 3.21" 2.80" 074093448
45° Angle with Male Fitting with Insulated Throat
Dimensions
M
Trade H J K L Throat N Catalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Number
³⁄₈ 1.25" 1.28" .66" 1.20" 1.06" .57" 1.16" 1.02" 074093561
½ 1.25" 1.28" .66" 1.34" 1.19" .57" 1.21" 1.06" 074093562
¾ 1.25" 1.44" .66" 1.55" 1.45" .78" 1.50" 1.32" 074093563
1 1.44" 1.53" .72" 1.95" 1.69" .98" 1.82" 1.59" 074093564
1¼ 1.48" 1.69" .69" 2.39" 2.06" 1.29" 2.32" 2.03" 074093565
1½ 1.72" 2.00" .72" 2.72" 2.38" 1.53" 2.62" 2.29" 074093566
2 1.75" 2.25" .72" 3.08" 2.87" 1.95" 3.21" 2.80" 074093568
90° Angle with Male Fitting
Dimensions
O
Trade D E F G Throat P Catalog
Size A/C* A/F* Ref. Dia. A/C* A/F* Number
³⁄₈ 1.31" .59" 1.20" 1.06" 1.44" .60" 1.13" .99" 074093421
½ 1.31" .59" 1.34" 1.12" 1.44" .61" 1.21" 1.00" 074093422
¾ 1.44" .59" 1.55" 1.45" 1.63" .83" 1.48" 1.29" 074093423
1 1.78" .66" 1.95" 1.60" 2.19" 1.05" 1.80" 1.57" 074093424
1¼ 1.97" .63" 2.39" 2.06" 2.50" 1.37" 2.32" 2.02" 074093425
1½ 2.19" .66" 2.72" 2.38" 2.69" 1.61" 2.58" 2.25" 074093426
2 2.53" .66" 3.08" 2.87" 3.25" 2.05" 3.14" 2.75" 074093428
90° Angle with Male Fitting with Insulated Throat
Dimensions
O
Trade D E F G Throat P Catalog
Size A/C* A/F* Ref. Dia. A/C* A/F* Number
³⁄₈ 1.38" .66" 1.20" 1.06" 1.44" .60" 1.13" .99" 074093541
½ 1.38" .66" 1.34" 1.12" 1.44" .57" 1.21" 1.00" 074093542
¾ 1.50" .66" 1.55" 1.45" 1.63" .78" 1.48" 1.29" 074093543
1 1.84" .66" 1.95" 1.60" 2.19" .98" 1.80" 1.57" 074093544
1¼ 2.03" .69" 2.39" 2.06" 2.50" 1.29" 2.32" 2.02" 074093545
1½ 2.25" .69" 2.72" 2.38" 2.69" 1.53" 2.58" 2.20" 074093546
2 2.59" .72" 3.08" 2.87" 3.25" 1.95" 3.14" 2.75" 074093548
2½ 3.44" 1.00" 3.92" 3.63" 4.25" 2.42" 3.78" 3.50" 074093550
3 3.75" 1.00" 4.70" 4.31" 4.87" 3.01" 4.64" 4.30" 074093552
Kellems® Wire Management Products Technical Information
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
Dimensions shown are approximate and
are subject to change without notice.
Note: *A/C - Across Corners; A/F - Across Flats.
J
M
Throat
Dia.
L
K
H
N
A/C A/F
D
Throat
Dia.
E
A/C A/F
C
A
Ref.
B
Ref.
G
O
Throat
Dia.
E
D
F
P
A/C A/F
T-80 Dimensions in Inches (cm)
www.hubbell-wiring.com
Dimensional Charts For UL Type A, Liquidtight Conduit Grip Fittings
Straight with Male Fitting with Insulated Throat
Dimensions Inches (cm)
Trade Size
N.P.T. Inches A B C D Catalog Number
³⁄₈ 1.922" (4.88) .594" (1.51) 1.156" (2.94) 3.75" (9.52) H038CNK
½ 1.922" (4.88) .594" (1.51) 1.250" (3.17) 4.50" (11.43) H050CNK
¾ 2.016" (5.12) .594" (1.51) 1.500" (3.81) 6.25" (15.87) H075CNK
1 2.157" (5.48) .719" (1.83) 1.844" (4.68) 7.50" (19.05) H100CNK
1¼ 2.219" (5.64) .750" (1.91) 2.312" (5.87) 9.00" (22.86) H125CNK
1½ 2.344" (5.95) .750" (1.91) 2.578" (6.55) 13.50" (34.29) H150CNK
2 2.406" (6.11) .750" (1.91) 3.187" (8.09) 14.50" (36.83) H200CNK
90° Angle with Male Fitting with Insulated Throat
Dimensions Inches (cm)
Trade Size
N.P.T. Inches E F G H I Catalog Number
³⁄₈ 1.250" (3.18) .594" (1.51) 1.156" (2.94) 1.453" (3.69) 3.75" (9.52) H0389CNK
½ 1.281" (3.25) .594" (1.51) 1.250" (3.17) 1.453" (3.69) 4.50" (11.43) H0509CNK
¾ 1.438" (3.65) .594" (1.51) 1.500" (3.81) 1.000" (2.54) 6.25" (15.87) H0759CNK
1 1.750" (4.44) .719" (1.83) 1.844" (4.68) 2.125" (5.40) 7.50" (19.05) H1009CNK
1¼ 1.969" (5.00) .750" (1.91) 2.312" (5.87) 2.344" (5.95) 9.00" (22.86) H1259CNK
1½ 2.250" (5.71) .750" (1.91) 2.578" (6.55) 2.500" (6.35) 13.50" (34.29) H1509CNK
2 2.531" (6.43) .750" (1.91) 3.187" (8.09) 2.781" (7.06) 14.50" (36.83) H2009CNK
C
Flats
A
Ref.
B
Ref.
D
H
I
F
E
G
Flats
Kellems® Wire Management Products
Technical Information
Strain Relief for Liquidtight Conduit
Technical Information Kellems® Wire Management Products
Dimensions shown are approximate and
are subject to change without notice.
T-81
Dimensions in Inches (cm) www.hubbell-wiring.com
Hubbell has the broadest line and the widest choice of
materials in the industry. N.P.T. hub sizes from ¼" to 3" in
straight male end, 90°, 45°, female and underground feed
connectors. They are available in your choice of aluminum,
plated steel, nylon and stainless steel.
Hubbell offers a full line of machined aluminum cord
connectors in N.P.T. hub sizes ¼" through 1" and cast
aluminum 1" to 3". They provide durable performance and
a clean attractive look without adding unwanted weight.
N.P.T. hub sizes ¼" to 1" feature an attractive knurled finish
which makes them easy to handle and maintain a U.L.
listing by hand tightening.
The zinc-plated steel cord connectors offers the strength
of steel and the corrosion resistance of zinc-plating. These
heavy-duty connectors hold up to most manufacturing
chemicals including acid solutions, solvents and other
corrosive materials.
Their machined steel nut and body allows for tightening
the compression nut and N.P.T. hub without worrying
about stripping the threads. For larger size cord, N.P.T.
hub sizes 1" to 2", Hubbell utilizes malleable iron
connectors which provide excellent holding and
liquidtight performance.
Hubbell’s nylon cord connectors resist most common
industrial corrosives and provide highly effective pullout
protection in a lightweight design. They are ideal for any
application where weight, conductivity or corrosion may
be an issue. They’re available in N.P.T. hub sizes from
¼" to 1".
Stainless steel cord connectors provide superior strength
and corrosion resistance for industrial and military
applications. They are machined from 300 series stainless
steel and come in ¼" to 1", N.P.T. hub sizes.
Kellems® Wire Management Products
Cord Connectors
Features and Benefits
Kellems® Wire Management Products Cord Connectors
Lubricated neoprene bushing compresses easily
for a liquidtight seal and added pull-out protection
The connector body is a one-piece design with
machined threads; a tapered interior seats the
bushing evenly for a liquidtight seal
Machined threads provide a strong positive seal;
the tapered interior dome easily drives the
bushing into the connector body
The patented GOTHCA® ring incorporates a
split hinge design to prevent friction and
provide strain relief, also color-coded
for sizing identification
Machined
Aluminum
Machined
Zinc-Plated Steel
T-82 Dimensions in Inches (cm)
www.hubbell-wiring.com
Straight Male
N.P.T. Cord Dia. Machined
Hub Inches Form Color Machined Zinc-Plated Stainless Nylon Nylon
Size (mm) Size Code Aluminum Steel Steel Gray Black
.06"-.13" Green — — — SHC1001CR —
(1.6-3.2)
.13"-.19" Orange SHC1002 — — SHC1002CR —
(3.2-4.7)
¼ .19"-.25" F1 Red SHC1003 — SHC1003SS SHC1003CR —
(4.7-6.3)
.25"-.31" Black SHC1004 — SHC1004SS SHC1004CR —
(6.3-7.9)
.31"-.38" White SHC1005** — — SHC1005CR SHC2005CR
(7.9-9.5)
.38"-.44" Blue — — — SHC1006CR —
(9.5-11)
.06"-.13" Green SHC1007 — — — —
(1.6-3.2)
.13"-.19" Orange SHC1008 SHC1008ZP — SHC1008CR SHC2008CR
(3.2-4.7)
³⁄₈ .19"-.25" F1 Red SHC1009 — SHC1009SS SHC1009CR —
(4.7-6.3)
.25"-.31" Black SHC1010 SHC1010ZP — SHC1010CR SHC2010CR
(6.3-7.9)
.31"-.38" White SHC1011 — SHC1011SS SHC1011CR SHC2011CR
(7.9-9.5)
.38"-.44" Blue SHC1012 SHC1012ZP SHC1012SS SHC1012CR SHC2012CR
(9.5-11.0)
.19"-.25" Red SHC1015 — — — —
(4.7-6.3)
½ .25"-.31" F1 Black SHC1016 — — — —
(6.3-7.9)
.31"-.38" White SHC1017 — — — —
(7.9-9.5)
.38"-.44" Blue SHC1018 — — — —
(9.5-11.0)
.06"-.13" Green SHC1019 — — SHC1019CR —
(1.6-3.2)
.13"-.19" Orange SHC1020 SHC1020ZP SHC1020SS SHC1020CR —
(3.2-.4.7)
½ .19"-.25" F2 Red SHC1021 SHC1021ZP SHC1021SS SHC1021CR SHC2021CR
(4.7-6.3)
.25"-.38" White SHC1022 SHC1022ZP SHC1022SS SHC1022CR SHC2022CR
(6.3-.9.7)
.38"-.50" Blue SHC1023 SHC1023ZP SHC1023SS SHC1023CR SHC2023CR
(9.7-12.7)
.50"-.63" Brown SHC1024 SHC1024ZP SHC1024SS SHC1024CR** SHC2024CR**
(12.7-15.9)
.38"-.50" Blue SHC1025 — — — —
(9.7-12.7)
.50"-.63" Brown SHC1026 — — — —
(12.7-15.9)
½ .63"-.75" F3 Yellow SHC1027** SHC1027ZP** — — —
(15.9-19.0)
.75"-.88" Orchid SHC1028** SHC1028ZP** — — —
(19.0-22.2)
Note:
See pages T-92 to T-101 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-89.
** Cable jacket may have to be stripped to pass through connector body.
Locknuts sold separately. See page T-89.
Kellems® Wire Management Products
Straight Male Cord Connectors
Form Size 1-3
Straight Male Cord Connectors Kellems® Wire Management Products
IP66*
SUITABILITY
UL Listed to Type 4,
4X, 12 and Type 13
Stainless
Steel
Gray Nylon
Black Nylon
T-83
Dimensions in Inches (cm) www.hubbell-wiring.com
Straight Male
N.P.T. Cord Dia. Machined
Hub Inches Form Color Machined Zinc-Plated Stainless Nylon Nylon
Size (mm) Size Code Aluminum Steel Steel Gray Black
.06"-.13" Green SHC1029 — — — —
(1.6-3.2)
.13"-.19" Orange SHC1030 SHC1030ZP — — —
(3.2-4.7)
¾ .19"-.25" F2 Red SHC1031 SHC1031ZP — — —
(4.7-6.3)
.25"-.38" White SHC1032 SHC1032ZP — — —
(6.3-9.7)
.38"-.50" Blue SHC1033 SHC1033ZP — — —
(9.7-12.7)
.50"-.63" Brown SHC1034 SHC1034ZP — — —
(12.7-15.9)
.38"-.50" Blue — SHC1035ZP SHC1035SS SHC1035CR SHC2035CR
(9.5-12.7)
¾ 50"-.63" F3 Brown SHC1036 — SHC1036SS SHC1036CR SHC2036CR
(12.7-15.9)
.63"-.75" Yellow SHC1037 SHC1037ZP SHC1037SS SHC1037CR SHC2037CR
(15.9-19.0)
.75"-.88" Orchid SHC1038** SHC1038ZP** SHC1038SS** SHC1038CR** SHC2038CR**
(19.0-22.2)
1 .50"-.63" F3 Brown — SHC1097ZP — — —
(12.7-15.9)
.63"-.75" Yellow — SHC1098ZP — — —
(15.9-19.0)
.75"-.88" Orchid — SHC1099ZP — — —
(19.0-22.2)
.38"-.50" Blue SHC1039 — — SHC1039CR —
(9.7-12.7)
.50"-.63" Brown SHC1040 — — SHC1040CR SHC2040CR
(12.7-15.9)
1 .63"-.75" F4 Yellow SHC1041 — SHC1041SS SHC1041CR SHC2041CR
(15.9-19.0)
.75"-.88" Orchid SHC1042 — SHC1042SS SHC1042CR SHC2042CR
(19.0-22.2)
.88"-1.00" Gray SHC1043 SHC1043ZP — SHC1043CR SHC2043CR
(22.2-25.4)
1.00"-1.13" Pink SHC1044** — SHC1044SS** SHC1044CR** SHC2044CR**
(25.4-28.6)
Note:
See pages T-92 to T-101 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-89.
** Cable jacket may have to be stripped to pass through connector body.
Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum.
Locknuts sold separately. See page T-89.
Kellems® Wire Management Products
Straight Male Cord Connectors
Form Size 2-4
Kellems® Wire Management Products Straight Male Cord Connectors
IP66*
SUITABILITY
UL Listed to Type 4,
4X, 12 and Type 13
Cast Aluminum
Cast Aluminum
Malleable Iron
T-84 Dimensions in Inches (cm)
www.hubbell-wiring.com
Straight Male
N.P.T. Cord Diameter Form
Hub Size Inches (mm) Size Cast Aluminum Malleable Iron
.88"-1.00" (22.2-25.4) SHC1046 —
1 1.00"-1.13" (25.4-28.6) F5 SHC1047** —
1.13"-1.25" (28.6-31.7) SHC1048** —
1.25"-1.38" (31.7-34.9) SHC1049** —
.75"-.88" (19.0-22.2) SHC1050 —
.88"-1.00" (22.2-25.4) SHC1051 —
1¼ 1.00"-1.13" (25.4-28.6) F5 SHC1052 SHC1052ZP
1.13"-1.25" (28.6-31.7) SHC1053 SHC1053ZP
1.25"-1.38" (31.7-34.9) SHC1054** SHC1054ZP
.75"-.88" (19.0-22.2) SHC1055 —
.88"-1.00" (22.2-25.4) SHC1056 —
1½ 1.00"-1.13" (25.4-28.6) F5 SHC1057 SHC1057ZP
1.13"-1.25" (28.6-31.7) SHC1058 SHC1058ZP
1.25"-1.38" (31.7-34.9) SHC1059 SHC1059ZP
1.38"-1.50" (34.9-38.1) SHC1061 —
1½ 1.50"-1.63" (38.1-41.3) F6 SHC1062** —
1.63"-1.75" (41.3-44.4) SHC1063** —
1.75"-1.88" (44.4-47.6) SHC1064** —
1.25"-1.38" (31.7-34.9) SHC1065 —
1.38"-1.50" (34.9-38.1) SHC1066 —
2 1.50"-1.63" (38.1-41.3) F6 SHC1067 —
1.63"-1.75" (41.3-44.4) SHC1068 —
1.75"-1.88" (44.4-47.6) SHC1069 —
1.69"-1.81" (42.9-46.0) SHC1070 —
1.81"-1.94" (46.0-49.2) SHC1071 —
2 1.94"-2.06" (49.2-52.4) F7 SHC1072** —
2.06"-2.19" (52.4-55.6) SHC1073** —
2.19"-2.31" (55.6-58.7) SHC1074** —
1.69"-1.81" (42.9-46.0) SHC1076 —
1.81"-1.94" (46.0-49.2) SHC1077 —
2½ 1.94"-2.06" (49.2-52.4) F7 SHC1078 —
2.06"-2.19" (52.4-55.6) SHC1079 —
2.19"-2.31" (55.6-58.7) SHC1080 —
2.31"-2.44" (58.7-61.9) SHC1081** —
1.69"-1.81" (42.9-46.0) SHC1086 —
1.94"-2.06" (49.2-52.4) F7 SHC1088 —
3 2.06"-2.19" (52.4-55.6) SHC1089 —
2.19"-2.31" (55.6-58.7) SHC1090 —
2.31"-2.44" (58.7-61.9) SHC1091 —
2.44"-2.63" (61.9-66.7) SHC1092 —
2.63"-2.81" (66.7-71.4) SHC1093 —
3 2.81"-3.00" (71.4-76.2) F8 SHC1094 —
3.00"-3.25" (76.2-82.5) SHC1095** —
Note:
See pages T-92 to T-101 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-89.
** Cable jacket may have to be stripped to pass through connector body.
Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum.
F5 and larger will not be color coded.
Locknuts sold separately. See page T-89.
Kellems® Wire Management Products
Straight Male Cord Connectors
Form Size 5-8
Straight Male Cord Connectors Kellems® Wire Management Products
IP66*
SUITABILITY
UL Listed to Type 4,
4X, 12 and Type 13
Machined
Aluminum †
Machined
Zinc-Plated Steel ∆
Cast Aluminum
T-85
Dimensions in Inches (cm) www.hubbell-wiring.com
45° Male
N.P.T. Machined
Hub Cord Diameter Form Color Machined Zinc-Plated Cast
Size Inches (mm) Size Code Aluminum† Steel∆ Aluminum
.19"-.25" (4.7-6.3) Red VHC1021 — —
½ .25"-.38" (6.3-9.7) F2 White VHC1022 VHC1022ZP —
.38"-.50" (9.7-12.7) Blue VHC1023 VHC1023ZP —
.50"-.63" (12.7-15.9) Brown VHC1024** VHC1024ZP** —
.38"-.50" (9.7-12.7) Blue VHC1035 — —
¾ .50"-.63" (12.7-15.9) F3 Brown VHC1036 — —
.63"-.75" (15.9-19.0) Yellow VHC1037** — —
1 .63"-.75" (15.9-19.0) F4 Yellow VHC1041 — —
.75"-.88" (19.0-22.2) Orchid VHC1042 — —
1¼ 1.00"-1.13" (25.4-28.6) F5 — — VHC1052
1.13"-1.25" (28.6-31.7) — — VHC1053**
Note:
See pages T-92 to T-101 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-89.
** Cable jacket may have to be stripped to pass through connector body.
Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum.
† Nuts are machined aluminum and bodies are cast aluminum.
∆ Nuts are machined zinc-plated steel and bodies are malleable iron, cadmium plated.
Locknuts sold separately. See page T-89.
Kellems® Wire Management Products
45° Male Cord Connectors
Form Size 2-5
Kellems® Wire Management Products 45° Male Cord Connectors
IP66*
SUITABILITY
UL Listed to Type 4,
4X, 12 and Type 13
Machined
Aluminum†Machined
Zinc-Plated Steel∆
Cast AluminumGray Nylon Black Nylon
T-86 Dimensions in Inches (cm)
www.hubbell-wiring.com
90° Male
N.P.T. Machined
Hub Cord Diameter Form Color Machined Zinc-Plated Nylon Nylon Cast
Size Inches (mm) Size Code Aluminum† Steel∆ Gray Black Aluminum
.25"-.31" (6.3-7.9) Black NHC1010 — — — —
³⁄₈ .31"-.38" (7.9-9.5) F1 White NHC1011 — — — —
.38"-.44" (9.5-11.0) Blue NHC1012 — — — —
.06"-.13" (1.6-3.2) Green — — — — —
.13"-.19" (3.2-4.7) Orange NHC1020 — NHC1020CR — —
½ .19"-.25" (4.7-6.3) F2 Red NHC1021 NHC1021ZP NHC1021CR — —
.25"-.38" (6.3-9.7) White NHC1022 NHC1022ZP NHC1022CR NHC2022CR —
.38"-.50" (9.7-12.7) Blue NHC1023 NHC1023ZP NHC1023CR NHC2023CR —
.50"-.63" (12.7-15.9) Brown NHC1024** NHC1024ZP** NHC1024CR** NHC2024CR** —
.38"-.50" (9.7-12.7) Blue NHC1035 NHC1035ZP NHC1035CR — —
¾ .50"-.63" (12.7-15.9) F3 Brown NHC1036 NHC1036ZP NHC1036CR — —
.63"-.75" (15.9-19.0) Yellow NHC1037 NHC1037ZP NHC1037CR — —
.75"-.88" (19.0-22.2) Orchid NHC1038 NHC1038ZP NHC1038CR — —
.50"-.63" (12.7-15.9) Brown NHC1040 — — — —
.63"-.75" (15.9-19.0) Yellow NHC1041 NHC1041ZP NHC1041CR NHC2041CR —
1 .75"-.88" (19.0-22.2) F4 Orchid NHC1042 — NHC1042CR NHC2042CR** —
.88"-1.00" (22.2-25.4) Gray NHC1043** — NHC1043CR NHC2043CR** —
1.00"-1.13" (25.4-28.7) Pink NHC1044** — — — —
.88"-1.00" (22.2-25.4) — — — — — NHC1051
1¼ 1.00"-1.13" (25.4-28.6) F5 — — — — — NHC1052
1.13"-1.25" (28.6-31.7) — — — — — NHC1053**
1.25"-1.38" (31.7-34.9) — — — — — NHC1054**
1.00"-1.13" (25.4-28.6) — — — — — NHC1057
1½ 1.13"-1.25" (28.6-31.7) F5 — — — — — —
1.25"-1.38" (31.7-34.9) — — — — — NHC1059
2 1.38"-1.50" (34.9-38.1) F6 — — — — — NHC1066
Note:
See pages T-92 to T-101 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-89.
** Cable jacket may have to be stripped to pass through connector body.
† Nuts are machined aluminum and bodies are cast aluminum.
∆ Compression nuts are machined zinc-plated steel and bodies are zinc-plated malleable iron.
Locknuts sold separately. See page T-89.
Kellems® Wire Management Products
90° Male Cord Connectors
Form Size 1-6
90° Male Cord Connectors Kellems® Wire Management Products
IP66*
SUITABILITY
UL Listed to Type 4,
4X, 12 and Type 13
Machined
Aluminum
Gray Nylon
Machined
Zinc-Plated Steel
Machined
Aluminum
Machined
Aluminum
T-87
Dimensions in Inches (cm) www.hubbell-wiring.com
Straight Female
N.P.T.
Hub Cord Diameter Form Color Machined
Size Inches (mm) Size Code Aluminum
½ .25"-.38" (6.3-9.7) F2 White FHC1022
.38"-.50" (9.7-12.7) Blue FHC1023
¾ .38"-.50" (9.7-12.7) F2 Blue FHC1033
.50"-.63" (12.7-15.9) Brown FHC1034
1 .75"-.88" (19.0-22.2) F4 Orchid FHC1042†
.88"-1.00" (22.2-25.4) Gray FHC1043†
Note: See pages
T-92 to T-101
for additional technical data and dimensional drawings.
* Cable jacket may have to be stripped to pass through connector body.
† Nuts are machined aluminum and bodies are cast aluminum.
Underground Feeder Connectors
N.P.T. UF** Machined
Hub Diameter Wire Machined Zinc-Plated Nylon Nylon
Size Inches (mm) Size Aluminum Steel Gray Black
½ .2"x.4" min (5.1 x 10.2) 2 # 14,
.25"-.55" max (6.3 x 14.0) 2 # 12, UFC0001 UFC0001ZP UFC0001CR UFC2001CR
2 # 10.
¾ .2"x.4" min (5.1x10.2) 2 # 14,
.25"-.55" max (6.3x14.0) 2 # 12, UFC0002 — — —
2 # 10.
¾ .2"x.6" min (5.1x15.2) 3 # 14,
.26"x.78" max (6.6x19.8) 3 # 12, UFC0003 — UFC0003CR UFC2003CR
3 # 10.
Note:
See pages T-92 to T-101 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-89.
** Wire sizes vary among manufacturers.
Locknuts sold separately. See page T-89.
Metric Aluminum Cord Connectors
Hub Cord Diameter Form
Size Inches (mm) Size Catalog Number
M16 .31"-.38" (7.9-9.7) F1 SHCM161011
M20 .31"-.38" (7.9-9.7) F1 SHCM201017
.25"-.38" (6.3-9.7) SHCM201022
M20 .38"-.50" (9.7-12.7) F2 SHCM201023
.50"-.62" (12.7-15.8) SHCM201024
M25 .38"-.50" (9.7-12.7) F2 SHCM251033
.50"-.62" (12.7-15.8) SHCM251034
M30 .63"-75" (15.9-19.0) F3 SHCM301037
Note: †
When used with metal clad O-ring shown on page T-89.
Non-metallic Locknuts sold separately. See page T-88.
Kellems® Wire Management Products
Straight Female, Underground Feeder and Metric Connectors
Form Size 1-4
IP66*
SUITABILITY
Kellems® Wire Management Products Straight Female, Underground Feeder and Metric Connectors
UL Listed to Type 4,
4X, 12 and Type 13 †
SEC100BA
SECP29GA
LNP29BPK25
T-88 Dimensions in Inches (cm)
www.hubbell-wiring.com
Low Profile N.P.T. Cord Connectors
N.P.T. Cord Diameter Catalog Non-metallic
Hub Size Inches (mm) Color Number Locknuts
³⁄₈ .18"-.31" (4.6-7.9) Gray SEC38GA* 31622002LPK50
³⁄₈ .18"-.31" (4.6-7.9) Black SEC38BA* 31622002LPK50
½ .17"-.45" (4.3-11.4) Gray SEC50GA 31622003LPK50
½ .17"-.45" (4.3-11.4) Black SEC50BA 31622003LPK50
¾ .45"-.71" (11.4-18.0) Gray SEC75GA 31622007LPK50
¾ .45"-.71" (11.4-18.0) Black SEC75BA 31622007LPK50
1 .59"-1.00" (15-25.4) Gray SEC100GA 31622008LPK50
1 .59"-1.00" (15-25.4) Black SEC100BA 31622008LPK50
Note: See pages T-92 to T-101 for additional technical data and dimensional drawings.
Catalog numbers with “PK50” suffix are bulk packed 50 pieces.
Low Profile PG∆ Cord Connectors
Cord Diameter Catalog Non-metallic
Hub Size Inches (mm) Color Number Locknuts
PG7 .11"-.25" (2.9-6.4) Gray SECP7GA* LNP7BPK100
PG7 .11"-.25" (2.9-6.4) Black SECP7BA* LNP7BPK100
PG9 .18"-.31" (4.6-7.9) Gray SECP9GA* LNP9BPK100
PG9 .18"-.31" (4.6-7.9) Black SECP9BA* LNP9BPK100
PG11 .23"-.40" (5.8-10.0) Gray SECP11GA* LNP11BPK100
PG11 .23"-.40" (5.8-10.0) Black SECP11BA* LNP11BPK100
PG13.5 .17"-.47" (4.3-11.9) Gray SECP13GA LNP13BPK100
PG13.5 .17"-.47" (4.3-11.9) Black SECP13BA LNP13BPK100
PG16 .23"-.53" (5.8-13.5) Gray SECP16GA LNP16BPK100
PG16 .23"-.53" (5.8-13.5) Black SECP16BA LNP16BPK100
PG21 .45"-.71" (11.4-17.9) Gray SECP21GA LNP21BPK100
PG21 .45"-.71" (11.4-17.9) Black SECP21BA LNP21BPK100
PG29 .59"-.99" (15-25.2) Gray SECP29GA LNP29BPK25
PG29 .59"-.99" (15-25.2) Black SECP29BA LNP29BPK25
PG36 .88"-1.30" (22.2-32.0) Gray SECP36GA LNP36BPK25
PG36 .88"-1.30" (22.2-32.0) Black SECP36BA LNP36BPK25
Low Profile Metric Cord Connectors
Cord Diameter Catalog Non-metallic
Hub Size Inches (mm) Color Number Locknuts
M12 .12"-.25" (2.9-6.4) Gray SECM12G LNM12BPK100
M12 .12"-.25" (2.9-6.4) Black SECM12B LNM12BPK100
M16 .11"-.31" (2.7-7.9) Gray SECM16G LNM16BPK100
M16 .11"-.31" (2.7-7.9) Black SECM16B LNM16BPK100
M20 .17"-.45" (4.3-11.4) Gray SECM20G* LNM20BPK100
M20 .17"-.45" (4.3-11.4) Black SECM20B* LNM20BPK100
M25 .49"-.71" (12.3-18.0) Gray SECM25G* LNM25BPK100
M25 .49"-.71" (12.3-18.0) Black SECM25B* LNM25BPK100
M32 .59"-1.00" (15.0-25.4) Gray SECM32G* LNM32BPK100
M32 .59"-1.00" (15.0-25.4) Black SECM32B* LNM32BPK100
M40 .87"-1.30" (22.0-32.0) Gray SECM40G LNM40BPK100
M40 .87"-1.30" (22.0-32.0) Black SECM40B LNM40BPK100
Note: See pages T-92 to T-101 for additional technical data and dimensional data.
Catalog numbers above with “PK10 0” suffix, i.e. LNP7BPK100, are bulk packed 100 per carton.
Catalog numbers above with “PK25” suffix, i.e. LNP29BPK25, are bulk packed 25 per carton.
* Items indicated are UL recognized components.
∆ Panzergewinde.
Kellems® Wire Management Products
Low Profile N.P.T., PG and Metric Thread Connectors
Non-Metallic Cord Connectors
Low Profile N.P.T., PG and Metric Thread Connectors Kellems® Wire Management Products
IP66*
SUITABILITY
Zinc-Plated
Steel Locknuts
Metal Clad
Sealing O-Rings
Non-Metallic
Locknuts
T-89
Dimensions in Inches (cm) www.hubbell-wiring.com
Cord Connector Parts
N.P.T. Cord Diameter Form Bushing GOTCHA® Ring
Hub Size Inches (mm) Size Catalog Number Color Code Catalog Number
¼, ³⁄₈, ½ .062"-.125" (1.58-3.17) F1 31518101BPK100 Green 31648035GPK100
.125"-.187" (3.17-4.76) 31518102BPK100 Orange 31648036GPK100
.187"-.250" (4.76-6.35) 31518103BPK100 Red 31648037GPK100
.250"-.312" (6.35-7.93) 31518104BPK100 Black 31648038GPK100
.312"-.375" (7.93-9.50) 31518105BPK100 White 31605010GPK100
.375"-.437" (9.50-11.1) 31518106BPK100 Blue 31648039GPK100
½, ¾ .187"-.250" (4.76-6.35) F2 31518110BPK100 Red 31648042GPK100
.250"-.375" (6.35-9.50) 31518111BPK100 White 31605015GPK100
.375"-.500" (9.50-12.7) 31518112BPK100 Blue 31648043GPK100
.500"-.625" (12.7-15.8) 31518113BPK100 Brown 31648044GPK100
½, ¾ .375"-.500" (9.50-12.7) F3 31518116BPK100 Blue 31648045GPK100
.500"-.625" (12.7-15.8) 31518117BPK100 Brown 31648046GPK100
.625"-.750" (15.8-19.0) 31518118BPK100 Yellow 31648047GPK100
.750"-.875" (19.0-22.2) 31518119BPK100 Orchid 31648048GPK100
1 .500"-.625" (12.7-15.8) F4 31518123BPK100 Brown 31648050GPK100
.625"-.750" (15.8-19.0) 31518124BPK100 Yellow 31648051GPK100
.750"-.875" (19.0-22.2) 31518125BPK100 Orchid 31648052GPK100
.875"-1.00" (22.2-25.4) 31518126BPK100 Gray 31648053GPK100
1.00"-1.125" (25.4-28.5) 31518127BPK100 Pink 31648054GPK100
Note: Catalog numbers above with “PK10 0” suffix, i.e. 31518101BPK100, are bulk packed 100 per carton.
Kellems® Wire Management Products
Accessories
Locknuts — Steel and Non-Metallic
N.P.T.
Hub Size Zinc-Plated Steel Non-Metallic
¼ — 31622001LPK50
³⁄₈ — 31622002LPK50
½ 00322001LPK50 31622003LPK50
¾ 00322002LPK50 31622007LPK50
1 00322003LPK50 31622008LPK50
1¼ 00322004LPK50 —
1½ 00322005LPK50 —
Note: Catalog numbers above with “PK50” suffix, i.e. 00322001LPK50, are bulk packed 50 per carton.
See page T-101 for additional technical data and dimensional drawings.
Metal Clad Sealing O-Rings
N.P.T.
Hub Size Catalog Number
½ 20509001
¾ 20509002
1 20509003
1¼ 20509004
1½ 20509005
2 20509006
2½ 20509007
3 20509008
Note: See page T-101 for additional technical data and dimensional drawings.
Kellems® Wire Management Products Accessories
Nylon spiral provides arc-of-bend control for cord protection
Nylon compression nut has a tapered interior dome
to easily drive the bushing into the connector body
Patented GOTCHA® ring incorporates
a split hinge design to prevent friction
and provide strain relief
Lubricated neoprene bushing compresses evenly for
a liquidtight seal and added pull-out protection
Nylon connector body is a one piece design with a tapered
interior that seals the bushing evenly for a positive seal
Threaded hexagon shaped nylon locknut secures tightly
and is also corrosion resistant
T-90 www.hubbell-wiring.com
Hubbell Juniors are a miniature liquidtight version of the full-sized Hubbell cord connectors. They feature
the same GOTCHA® ring technology and neoprene bushings. They also come with or without a nylon
spiral for arc-of-bend control and longer cord life. They are available in ¼", ³⁄₈", and ½" N.P.T. sizes
in both gray and black.
Kellems® Wire Management Products
Hubbell Juniors® Miniature Connectors
Hubbell Juniors® Miniature Connectors Kellems® Wire Management Products
T-91
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Hubbell Juniors® Miniature Nylon Cord Connectors
Gray Cord Connector
Black Cord Connector
Gray Cord Connector with Spiral
Black Cord Connector with Spiral
Gray Snap-In
Cord Connector
Black Snap-In
Cord Connector
Miniature Nylon Cord Connector
N.P.T. Cord Diameter Range
Hub Size Inches (mm) Gray Black
.08"-.14" (1.9-3.4) HJ1001GPK25 HJ1001BPK25
¼ .14"-.20" (3.4-5.1) HJ1002GPK25 HJ1002BPK25
.20"-.27" (5.1-6.7) HJ1003GPK25 HJ1003BPK25
.15"-.21" (3.7-5.3) HJ1004GPK25 HJ1004BPK25
³⁄₈ .21"-.28" (5.3-7.0) HJ1005GPK25 HJ1005BPK25
.28"-.34" (7.0-8.6) HJ1006GPK25 HJ1006BPK25
.06"-.13" (1.6-3.2) HJ1055GPK25 HJ1055BPK25
.13"-.19" (3.2-4.7) HJ1056GPK25 HJ1056BPK25
½ .19"-.25" (4.7-6.3) HJ1057GPK25 HJ1057BPK25
.25"-.31" (6.3-7.9) HJ1058GPK25 HJ1058BPK25
.31"-.38" (7.9-9.5) HJ1059GPK25 HJ1059BPK25
.38"-.44" (9.5-11.1) HJ1060GPK25 HJ1060BPK25
Miniature Nylon Cord Connector with Spiral
N.P.T. Cord Diameter Range
Hub Size Inches (mm) Gray Black
.08"-.14" (1.9-3.4) HJ1010GPK25 HJ1010BPK25
¼ .14"-.20" (3.4-5.1) HJ1011GPK25 HJ1011BPK25
.20"-.27" (5.1-6.7) HJ1012GPK25 HJ1012BPK25
.15"-.21" (3.7-5.3) HJ1013GPK25 HJ1013BPK25
³⁄₈ .21"-.28" (5.3-7.0) HJ1014GPK25 HJ1014BPK25
.28"-.34" (7.0-8.6) HJ1015GPK25 HJ1015BPK25
.13"-.19" (3.2-4.7) HJ1038GPK25 HJ1038BPK25
.19"-.25" (4.7-6.3) HJ1039GPK25 HJ1039BPK25
½ .25"-.31" (6.3-7.9) HJ1040GPK25 HJ1040BPK25
.31"-.38" (7.9-9.5) HJ1041GPK25 HJ1041BPK25
.38"-.44" (9.5-11.1) HJ1042GPK25 HJ1042BPK25
¾ .25"-.49" (6.4-12.3) HJ1043GPK25* HJ1043BPK25*
.45"-.71" (11.4-18.0) HJ1044GPK25* HJ1044BPK25*
Note: * Locknuts sold separately. See page T-89.
Miniature Nylon Snap-In Cord Connector with Spiral
Cord Diameter Range For Chassis
Inches (mm) Thickness Gray Black
.22"-.27" (5.6-6.9) .10" (2.5) Max HS1001GPK25 HS1001BPK25
.28"-.32" (7.1-8.1) .10" (2.5) Max HS1002GPK25 HS1002BPK25
.30"-.36" (7.6-9.1) .13" (3.2) Max HS1003GPK25 HS1003BPK25
.32"-.43" (8.1-10.9) .13" (3.2) Max HS1004GPK25 HS1004BPK25
Note: Catalog numbers above with “PK25” suffix, i.e. HJ1001GPK25, are bulk packed 25 per carton.
See pages T-102 and T-103 for additional technical data and dimensional drawings.
Kellems® Wire Management Products
Hubbell Juniors® Miniature Nylon Cord Connectors
T-92 Dimensions in Inches (cm)
www.hubbell-wiring.com
Operating Temperatures
Material Temperature Range
Aluminum -40°F to +300°F (-40°C to +149°C)
Nylon (connectors and GOTCHA® rings) -40°F to +225°F (-40°C to +107°C)
Plated steel* -60°F to +1000°F (-51°C to +537°C)
Stainless steel* -60°F to +1000°F (-51°C to +537°C)
Neoprene (bushings) -30°F to +240°F (-34°C to +115°C)
Note: * Due to the limiting factors of nylon and neoprene, any complete cord connector with a GOTCHA ring, Form 1-5, will continuously
perform in the range of -30°F to +225°F (-34°C to +107°C).
Cord connectors without GOTCHA rings, Form 6-8, will continuously operate in the range -30°F to +240°F (-34°C to +115°C)
due to the limiting factor of neoprene.
Hazardous Locations
Hubbell cord connectors are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class Ill Div. 1 & 2 in
accordance with the NEC.
Flammability
Hubbell nylon cord connectors have a UL 94-V2 rating.
Approvals
Agency
UL Listed in accordance with Standard 514B.
CSA Certified.
United States Coast Guard Approved, Title 46-Part 111.
Form Size Definition
The term “Form Size” refers to the physical overall size of a cord connector.
Form 1 is the smallest size.
Form 8 is the largest size.
Knockout Holes
Knockout Hole Recommended Knockout Hole Recommended Knockout Hole Recommended
N.P.T. Min. to Max. PG Metric
Hub Size Inches (mm) Hub Size Inches (mm) Hub Size Inches (mm)
¼ .54"-.57" (13.7-14.5) PG7 492" (12.5) M12 .472" (12)
³⁄₈ .67"-.70" (17.0-17.8) PG9 599" (15.2) M16 .629" (16)
½ .86"-.91" (21.8-23.0) PG11 .733" (18.6) M20 .787" (20)
¾ 1.04"-1.09" (26.4-27.8) PG13.5 .804" (20.4) M25 .984" (25)
1 1.36"-1.41" (34.5-35.7) PG16 .888" (22.5) M32 1.25" (32)
1¼ 1.72"-1.77" (43.7-44.9) PG21 1.15" (28.3) M40 1.57" (40)
1½ 1.97"-2.02" (50.0-51.2) PG29 1.47" (34.3)
2 2.45"-2.50" (62.3-63.5) PG36 1.85" (47.0)
2½ 2.95"-3.00" (75.0-76.2)
3 3.58"-3.63" (90.9-92.1)
N.P.T., PG and Metric Thread Low Profile Connectors
Specifications
Material 6/6 Nylon.
Gland Buna N.
Temperature Range -22°F to 225°F (-30°C to 107°C).
Cord Connectors are Halogen and Silicon free.
Protection Class IP66 Suitability.
Flammability UL 94V-2.
Listings/Certifications UL Listing File E-41567, UL Recognition File E-41567.
CSA File LR27378C, VDE Marks Licence #136681.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Cord Connectors
SECP29G
T-93
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
A
(Overall)
B Ref.
C
D
F
E
Straight Hubbell Connectors
Aluminum Inches (mm) Nylon Inches (mm)
F A B C D E A B C D E
Throat Throat
N.P.T. Form Dia. Ref. Dia. A/C* A/F* Dia. Ref. Dia. A/C* A/F*
¼-18 1 .88" .90" .46" .32" .99" .88" 1.00" 1.10" .43" .33" .1.00" .93"
(22.4) (22.9) (11.7) (8.1) (25.1) (22.4) (25.4) (27.9) (10.9) (8.4) (25.4) (23.6)
³⁄₈-18 1 .88" .90" .46" .44" .99" .88" 1.00" 1.10" .43" .45" 1.00" .93"
(22.4) (22.9) (11.7) (11.2) (25.1) (22.4) (25.4) (27.9) (10.9) (11.4) (25.4) (23.6)
½-14 1 .88" .90" .46" .44" 1.00" .88" 1.00" 1.10" .46" .45" 1.00" .93"
(22.4) (22.9) (11.7) (11.2) (25.4) (22.4) (25.4) (27.9) (11.7) (11.4) (25.4) (23.6)
½-14 2 1.13" 1.10" .55" .64" 1.11" 1.00" 1.32" 1.50" .53" .58" 1.25" 1.12"
(28.7) (27.9) (14.0) (16.3) (28.2) (25.4) (33.5) (38.1) (13.5) (14.7) (31.7) (28.4)
½-14 3 1.38" 1.50" .55" .64" 1.40" 1.25" — — — — — —
(35.1) (38.1) (14.0) (16.3) (35.6) (31.7)
¾-14 2 1.13" 1.10" .55" .64" 1.29" 1.13" — — — — — —
(28.7) (27.9) (14.0) (16.3) (32.8) (28.7)
¾-14 3 1.38" 1.50" .55" .82" 1.40" 1.25" 1.56" 1.60" .55" .77" 1.44" 1.31"
(35.1) (38.1) (14.0) (20.8) (35.6) (31.7) (39.6) (40.6) (14.0) (19.6) (36.6) (33.3)
1-11½ 4 1.75" 1.60" .71" 1.02" 1.81" 1.62" 1.88" 1.75" .70" 1.01" 1.84" 1.63"
(44.4) (40.6) (18.0) (25.9) (46.0) (41.1) (47.8) (44.4) (17.8) (25.7) (46.7) (41.4)
1-11½ 5 2.31" 1.70" .66" 1.01" 2.28" 2.00" — — — — — —
(58.7) (43.2) (16.8) (25.7) (57.9) (50.8)
1¼-11½ 5 2.31" 1.70" .74" 1.26" 2.28" 2.12" — — — — — —
(58.7) (43.2) (18.8) (32.0) (57.9) (53.8)
1½-11½ 5 2.31" 1.70" .74" 1.38" 2.28" 2.12" — — — — — —
(58.7) (43.2) (18.8) (35.1) (57.9) (53.8)
1½-11½ 6 3.00" 2.20" .75" 1.50" 2.97" 2.75" — — — — — —
(76.2) (55.9) (19.0) (38.1) (75.4) (69.8)
2-11½ 6 3.00" 2.20" .80" 1.92" 3.24" 3.00" — — — — — —
(76.2) (55.9) (20.3) (48.8) (82.4) (76.2)
2-11½ 7 3.85" 2.70" .88" 1.94" 4.05" 3.75" — — — — — —
(97.8) (68.6) (22.4) (49.3) (102.9) (95.2)
2½-8 7 3.85" 2.70" 1.30" 2.32" 4.34" 4.02" — — — — — —
(97.8) (68.6) (33.0) (58.9) (110.2) (102.1)
2½-8 8 4.75" 2.70" 1.25" 2.38" 4.86" 4.50" — — — — — —
(120.6) (68.6) (31.7) (60.5) (123.4) (114.3)
3-8 7 3.85" 2.70" 1.30" 2.54" 4.34" 4.02" — — — — — —
(97.8) (68.6) (33.0) (64.5) (110.2) (102.1)
3-8 8 4.50" 2.70" 1.38" 3.00" 4.86" 4.50" — — — — — —
(114.3) (68.6) (35.1) (76.2) (123.4) (114.3)
Note: *A/C— Across Corners; A/F—Across Flats.
Kellems® Wire Management Products
Technical Information
Cord Connectors
Dimensions shown are approximate and
are subject to change without notice.
A
(Overall)
B Ref.
C
D
F
E
T-94 Dimensions in Inches (cm)
www.hubbell-wiring.com
Straight Hubbell Connectors
Zinc-Plated Steel Inches (mm) Stainless Steel Inches (mm)
F A B C D E A B C D E
Throat Throat
N.P.T. Form A/C* A/F* Ref. Dia. A/C* A/F* A/C* A/F* Dia. A/C* A/F*
¼- 18 1 — — — — — — — 1.01" .88" .90" .46" .38" .87" .75"
(25.7) (22.4) (22.9) (11.7) (9.7) (22.1) (19.0)
³⁄₈-18 1 .98" .88" .90" .42" .45" .99" .88" 1.01" .88" .90" .46" .45" .87" .75"
(24.9) (22.4) (22.9) (10.7) (11.4) (25.1) (22.4) (25.7) (22.4) (22.9) (11.7) (11.4) (22.1) (19.0)
½-14 1 .98" .88" .90" .55" .45" 1.00" .88" — — — — — — —
(24.9) (22.4) (22.9) (14.0) (11.4) (25.4) (22.4)
½-14 2 1.27" 1.13" 1.20" .55" .64" 1.10" 1.00" 1.30" 1.13" 1.10" .54" .63" 1.16" 1.00"
(32.3) (28.7) (30.5) (14.0) (16.3) (28.2) (25.4) (33.0) (28.7) (27.9) (13.7) (16.0) (29.5) (25.4)
½-14 3 1.55" 1.38" 1.50" .55" .64" 1.40" 1.25" — — — — — — —
(39.4) (35.1) (38.1) (14.0) (16.3) (35.6) (31.7)
¾-14 2 1.27" 1.13" 1.20" .55" .64" 1.29" 1.13" — — — — — — —
(32.3) (28.7) (30.5) (14.0) (16.3) (32.8) (28.7)
¾-14 3 1.55" 1.38" 1.40" .55" .82" 1.40" 1.25" 1.59" 1.38" 1.30" .56" .81" 1.44" 1.25"
(39.4) (35.1) (35.6) (14.0) (20.8) (35.6) (31.7) (40.4) (35.1) (33.0) (14.2) (20.6) (36.6) (31.7)
1-11½ 3 1.55" 1.38" 1.40" .70" .89" 1.54" 1.38" — — — — — — —
(39.4) (35.1) (35.6) (17.8) (22.6) (39.1) (35.1)
1-11½ 4 1.92" 1.69" 1.60" .70" 1.02" 1.95" 1.69" 2.02" 1.75" 1.40" .70" 1.03" 1.88" 1.63"
(48.8) (42.9) (40.6) (17.8) (25.9) (49.5) (42.9) (51.3) (44.4) (35.6) (17.8) (26.2) (47.8) (41.4)
1-11½ 5 2.40" 1.70" .70" 1.02" 2.46" 2.15" — — — — — — —
(61.0) (43.2) (17.8) (25.9) (62.5) (54.6)
1¼-11½ 5 2.40" 1.70" .73" 1.27" 2.48" 2.19" — — — — — — —
(61.0) (43.2) (18.5) (32.3) (63.0) (55.6)
1½-11½ 5 2.40" 1.70" .74" 1.39" 2.48" 2.19" — — — — — — —
(61.0) (43.2) (18.8) (35.3) (63.0) (55.6)
1½-11½ 6 3.06" 2.20" .75" 1.52" 3.04" 2.83" — — — — — — —
(77.7) (55.9) (19.0) (38.6) (77.2) (71.9)
2-11½ 6 3.06" 2.20" .78" 1.92" 3.32" 3.07" — — — — — — —
(77.7) (55.9) (19.8) (48.8) (84.3) (78.0)
2-11½ 7 3.95" 2.70" .78" 1.99" 4.18" 3.89" — — — — — — —
(100.3) (68.6) (19.8) (50.5) (106.2) (98.8)
2½-8 7 — — — — — — — — — — — — — —
2½-8 — — — — — — — — — — — — — — —
3-8 7 — — — — — — — — — — — — — —
3-8 8 — — — — — — — — — — — — — —
Note: *A/C— Across Corners; A/F—Across Flats.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Cord Connectors
Dimensions shown are approximate and
are subject to change without notice.
T-95
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
Dimensions shown are approximate and
are subject to change without notice.
B Ref.
A
Ref.
D
C
E
F
G
B Ref.
A
D
C
E
F
G
45° Hubbell Connectors
Aluminum Inches (mm) Zinc Plated Steel Inches (mm)
F A B C D E G A B C D E G
Throat Across Across Throat Across Across Across Across
N.P.T. Form Ref. Ref. Dia. Corners Flats Dia. Ref. Ref. Dia. Corners Flats Corners Flats
½-14 2 2.00" 1.90" .55" .56" 1.27" 1.10" 1.13" 1.97" 1.90" .55" .57" 1.24" 1.06" 1.27" 1.13"
(50.8) (48.3) (14.0) (14.2) (32.3) (27.9) (28.6) (50.0) (48.3) (14.0) (14.4) (31.5) (26.9) (32.3) (28.6)
¾-14 3 2.30" 2.50" .56" .75" 1.48" 1.28" 1.38" — — — — — — — —
(58.4) (65.3) (14.2) (19.0) (37.6) (32.5) (34.9)
1-11½ 4 2.60" 2.80" .70" 1.00" 1.69" 1.50" 1.75" — — — — — — — —
(66.0) (71.1) (17.8) (25.4) (42.9) (38.1) (44.4)
1½-11½ 5 3.90" 3.90" .74" 1.25" 2.45" 2.13" 2.31" — — — — — — — —
(99.1) (9.91) (18.8) (31.7) (62.2) (54.0) (58.7)
1½-11½ 5 3.90" 3.90" .74" 1.50" 2.45" 2.13" 2.31" — — — — — — — —
(99.1) (99.1) (18.8) (38.1) (62.2) (54.0) (58.7)
90° Hubbell Connectors
Aluminum Inches (mm) Zinc Plated Steel Inches (mm)
F A B C D E G A B C D E G
Throat Across Across Throat Across Across Across Across
N.P.T. Form Ref. Dia. Corners Flats Dia. Ref. Dia. Corners Flats Corners Flats
³⁄₈-18 1 1.27" 2.00" .46" .44" 1.15" 1.10" .88" — — — — — — — —
(32.3) (50.8) (11.7) (11.2) (29.2) (27.9) (22.2)
½-14 2 1.56" 2.30" .50" .55" 1.30" 1.13" 1.13" 1.65" 2.38" .55" .55" 1.29" 1.13" 1.27" 1.13"
(39.6) (58.4) (12.7) (13.9) (33.0) (28.7) (28.6) (41.9) (60.5) (14.0) (13.8) (32.8) (28.7) (32.3) (28.6)
¾-14 3 1.79" 2.80" .56" .77" 1.49" 1.31" 1.38" 1.88" 2.90" .56" .77" 1.52" 1.33" 1.55" 1.38"
(45.5) (71.1) (14.2) (19.4) (37.8) (33.3) (34.9) (47.8) (73.7) (14.2) (19.4) (38.6) (33.8) (39.2) (34.9)
1-11½ 4 2.08" 3.20" .70" 1.00" 1.70" 1.50" 1.75" 2.16" 3.20" .70" 1.00" 1.72" 1.50" 1.92" 1.69"
(52.8) (81.3) (17.8) (25.4) (43.2) (38.1) (44.4) (54.9) (81.3) (17.8) (25.4) (43.7) (38.1) (48.8) (42.8)
1¼-11½ 5 3.18" 4.30" .73" 1.26" 2.47" 2.15" 2.31" — — — — — — — —
(80.8) (109.2) (18.5) (32.0) (62.7) (54.6) (58.7)
1½-11½ 5 3.18" 4.30" .75" 1.50" 2.47" 2.15" 2.31" — — — — — — — —
(80.8) (109.2) (19.2) (38.1) (62.7) (54.6) (58.7)
2-11½ 6 3.51" 5.50" .80" 1.92" 2.98" 2.78" 3.00" — — — — — — — —
(89.2) (139.7) (20.3) (48.8) (75.7) (70.6) (76.2)
90° Hubbell Connectors
Nylon Inches (mm)
F A B C D E G
Throat Across Across
N.P.T. Form Ref. Dia. Corners Flats Dia.
³⁄₈-18 1 — — — — — — —
½-14 2 1.41" 2.50" .55" .58" 1.23" 1.12" 1.32"
(35.8) (63.5) (14.0) (14.6) (31.2) (28.2) (33.4)
¾-14 3 1.65" 2.81" .56" .77" 1.42" 1.29" 1.56"
(41.9) (71.4) (14.2) (19.4) (36.1) (32.8) (39.6)
1-11½ 4 1.99" 3.30" .70" 1.01" 1.82" 1.60" 1.88"
(50.5) (83.8) (17.8) (25.7) (46.2) (40.6) (47.6)
Kellems® Wire Management Products
Technical Information
Cord Connectors
A
DC
F
B
E
SEALING NUT
A
(Overall)
B Ref.
C
D
F
E
A
(Overall)
B Ref.
C (N.P.T. Thread Depth)
D
E
Recommended
knockout size
T-96 Dimensions in Inches (cm)
www.hubbell-wiring.com
Low Profile Non-Metallic N.P.T., PG and Metric Thread Connectors
Nylon Inches (mm)
Hub Size A B C D E F
³⁄₈ N.P.T. 0.670" (17.0) 1.41" (35.8) 0.48" (12.4) 0.21" (5.3) 0.83" (21.0) 0.55" (14.0)
½ N.P.T. 0.875" (22.2) 1.70" (43.2) 0.61" (15.5) 0.21" (5.3) 0.88" (24.8) 0.66" (16.8)
¾ N.P.T. 1.068" (27.1) 2.00" (50.8) 0.62" (15.7) 0.25" (6.3) 1.30" (33.0) 0.85" (21.6)
1 N.P.T. 1.375" (35.0) 2.41" (61.2) 0.76" (19.3) 0.30" (7.6) 1.73" (43.9) 1.05" (26.7)
PG7 0.492" (12.5) 1.16" (29.5) 0.32" (8.1) 0.21" (5.3) 0.63" (16.0) 0.48" (12.4)
PG9 0.599" (15.2) 1.25" (31.8) 0.32" (8.1) 0.21" (5.3) 0.83" (21.0) 0.55" (14.0)
PG11 0.733" (18.6) 1.48" (37.6) 0.38" (9.7) 0.21" (5.3) 0.94" (23.9) 0.70" (17.8)
PG13.5 0.804" (20.4) 1.53" (38.9) 0.41" (10.4) 0.21" (5.3) 0.98" (24.9) 0.66" (16.8)
PG16 0.888" (22.5) 1.68" (42.7) 0.44" (11.2) 0.25" (6.4) 1.06" (27.0) 0.76" (19.3)
PG21 1.15" (28.3) 1.89" (48.0) 0.52" (13.2) 0.25" (6.4) 1.30" (33.0) .085" (21.6)
PG29 1.47" (37.30) 2.23" (56.6) 0.58" (14.7) 0.30" (7.6) 1.73" (43.9) 1.05" (26.7)
PG36 1.85" (47.0) 2.39" (60.7) 0.47" (11.9) 0.31" (7.9) 2.05" (52.7) 1.19" (30.2)
M12 0.473" (12.0) 1.16" (29.5) 0.32" (8.1) 0.21" (5.3) 0.63" (16.0) 0.49" (12.4)
M16 0.630" (16.0) 1.25" (31.8) 0.32" (8.1) 0.21" (5.3) 0.83" (21.0) 0.55" (14.0)
M20 0.787" (20.0) 1.53" (38.9) 0.41" (10.4) 0.21" (5.3) 0.98" (24.9) 0.66" (16.8)
M25 0.985" (25.0) 1.89" (48.0) 0.52" (13.2) 0.25" (6.3) 1.30" (33.0) 0.85" (21.6)
M32 1.260" (32.0) 2.23" (56.6) 0.58" (14.7) 0.30" (7.6) 1.73" (43.9) 1.05" (26.7)
M40 1.575" (40.0) 2.39" (60.7) 0.48" (12.2) 0.30" (7.6) 2.05" (52.1) 1.19" (30.2)
Female Hubbell Connectors
Aluminum Inches (mm)
F A B C D E
Throat Across Across
N.P.T. Form Dia. Ref. Dia. Corners Flats
³⁄₈-18 1 .88" 1.40" .56" .44" .94" .81"
(22.4) (35.6) (14.2) (11.2) (23.9) (20.6)
½-14 2 1.13" 1.80" .56" .63" 1.15" 1.00"
(28.7) (45.7) (14.2) (16.0) (29.2) (25.4)
¾-14 2 1.13" 2.10" .75" .63" 1.44" 1.25"
(28.7) (53.3) (19.0) (16.0) (36.6) (31.7)
1-11½ 4 1.75" 2.30" .88" 1.10" 1.88" 1.63"
(44.5) (58.4) (22.4) (27.9) (47.8) (41.4)
1¼-11½ 5 2.31" 2.80" .95" 1.43" 2.64" 2.29"
(58.7) (71.1) (24.1) (36.3) (67.1) (58.2)
1½-11½ 5 2.31" 2.80" .95" 1.43" 2.64" 2.29"
(58.7) (71.1) (24.1) (36.3) (67.1) (58.2)
Underground Feeder Connectors
Aluminum Inches (mm) Nylon Inches (mm) Zinc-Plated Steel Inches (mm)
F A B C D E A B C D E A B C D E
Thrt. Thrt. Thrt.
N.P.T. Form Dia. Ref. Dia. A/C* A/F* Dia. Ref. Dia. A/C* A/F* A/C* A/F* Ref. Dia. A/C* A/F*
½-14 2 1.13" 1.10" .55" .64" 1.10" 1.00" 1.32" 1.50" .55" .58" 1.25" 1.13" 1.27" 1.13" 1.20" .55" .64" 1.11" 1.00"
(28.7) (27.9) (14.0) (16.3) (27.9) (25.4) (33.5) (38.1) (14.0) (14.7) (31.7) (28.7) (32.3) (28.7) (30.5) (14.0) (16.3) (28.2) (25.4)
¾-14 2 1.13" 1.10" .55" .64" 1.29" 1.13" — — — — — — 1.27" 1.13" 1.20" .55" .64" 1.29" 1.13"
(28.7) (27.9) (14.0) (16.3) (32.8) (25.4) (32.3) (28.7) (30.5) (14.0) (16.3) (32.8) (28.7)
¾-14 3 1.13" 1.50" .55" .82" 1.40" 1.25" 1.56" 1.60" .56" .77" 1.44" 1.31" 1.55" 1.38" 1.40" .56" .82" 1.40" 1.25"
(28.7) (38.1) (14.0) (20.8) (35.6) (31.7) (39.6) (40.6) (14.2) (19.6) (36.6) (33.3) (39.4) (35.1) (35.6) (14.2) (20.8) (35.6) (31.7)
Note: *A/C - Across Corners; A/F - Across Flats.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Cord Connectors
T-97
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
2 Conductors
SVO,
SV,
Cord Type SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8
Approximate .25" .31" .33" .37" .38" .40" .54" .62" .68" .81"
Diameter (6.2) (7.8) (8.4) (9.3) (9.7) (10.2) (13.7) (15.6) (17.1) (20.6)
Color Black Black White White Blue Blue Brown Brown Yellow Orchid
N.P.T. Form Catalog Number*
¼ 1 HC1004 HC1004 HC1005 HC1005 HC1006 HC1006 — — — —
³⁄₈ 1 HC1010 HC1010 HC1011 HC1011 HC1012 HC1012 — — — —
½ 1 HC1016 HC1016 HC1017 HC1017 HC1018 HC1018 — — — —
½ 2 HC1022 HC1022 HC1022 HC1022 HC1023 HC1023 HC1024 HC1024 — —
½ 3 — — — — HC1025 HC1025 HC1026 HC1026 HC1027 HC1028
¾ 2 HC1032 HC1032 HC1032 HC1032 HC1033 HC1033 HC1034 HC1034 — —
¾ 3 — — — — HC1035 HC1035 HC1036 HC1036 HC1037 HC1038
1 4 — — — — HC1039 HC1039 HC1040 HC1040 HC1041 HC1042
1 5 — — — — — — — — — HC1045
1¼ 5 — — — — — — — — — HC1050
1½ 5 — — — — — — — — — HC1055
1½ 6 — — — — — — — — — —
2 6 — — — — — — — — — —
2 7 — — — — — — — — — —
2½ 7 — — — — — — — — — —
3 7 — — — — — — — — — —
Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100.
‡ F5 and larger will not be color coded.
3 Conductors
SVO,
SV,
Cord Type SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8
Approximate .26" .33" .35" .39" .39" .42" .57" .65" .71" .85"
Diameter (6.5) (8.3) (8.9) (9.8) (9.9) (10.7) (14.4) (16.4) (18.0) (21.5)
Color Black White White Blue Blue Blue Brown Yellow Yellow Orchid
N.P.T. Form Catalog Number*
¼ 1 HC1004 HC1005 HC1005 HC1006 HC1006 HC1006 — — — —
³⁄₈ 1 HC1010 HC1011 HC1011 HC1012 HC1012 HC1012 — — — —
½ 1 HC1016 HC1017 HC1017 HC1018 HC1018 HC1018 — — — —
½ 2 HC1022 HC1022 HC1022 HC1023 HC1023 HC1023 HC1024 — — —
½ 3 — — — HC1025 HC1025 HC1025 HC1026 HC1027 HC1027 HC1028
¾ 2 HC1032 HC1032 HC1032 HC1033 HC1033 HC1033 HC1034 — — —
¾ 3 — — — HC1035 HC1035 HC1035 HC1036 HC1037 HC1037 HC1038
1 4 — — — HC1039 HC1039 HC1039 HC1040 HC1041 HC1041 HC1042
1 5 — — — — — — — — — HC1045
1¼ 5 — — — — — — — — — HC1050
1½ 5 — — — — — — — — — HC1055
1½ 6 — — — — — — — — — —
2 6 — — — — — — — — — —
2 7 — — — — — — — — — —
2½ 7 — — — — — — — — — —
3 7 — — — — — — — — — —
Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100.
‡ F5 and larger will not be color coded.
Kellems® Wire Management Products
Technical Information
Cord Connectors
T-98 Dimensions in Inches (cm)
www.hubbell-wiring.com
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Cord Connectors
2 Conductors
SVO,
SV,
Cord Type SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250
Approximate .94" 1.08" 1.17" 1.27" 1.44" 1.52" 1.65" 1.77" 1.92" 2.16"
Diameter (23.8) (27.4) (29.7) (33.3) (36.6) (38.6) (41.9) (45.0) (48.8) (51.9)
Color Gray‡ Pink‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
N.P.T. Form Catalog Number*
¼ 1 — — — — — — — — — —
³⁄₈ 1 — — — — — — — — — —
½ 1 — — — — — — — — — —
½ 2 — — — — — — — — — —
½ 3 — — — — — — — — — —
¾ 2 — — — — — — — — — —
¾ 3 — — — — — — — — — —
1 4 HC1043 HC1044 — — — — — — — —
1 5 HC1046 HC1047 HC1048 HC1049 — — — — — —
1¼ 5 HC1051 HC1052 HC1053 HC1054 — — — — — —
1½ 5 HC1056 HC1057 HC1058 HC1059 — — — — — —
1½ 6 — — — HC1060 HC1061 HC1062 HC1063 HC1064 — —
2 6 — — — HC1065 HC1066 HC1067 HC1068 HC1069 — —
2 7 — — — — — — — HC1070 HC1071 HC1073
2½ 7 — — — — — — — HC1076 HC1077 HC1079
3 7 — — — — — — — HC1086 HC1087 HC1089
Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100.
‡ F5 and larger will not be color coded.
3 Conductors
SVO,
SV,
CordType SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250
Approximate 1.00" 1.17" 1.24" 1.34" 1.51" 1.65" 1.75" 1.80" 2.07" 2.39"
Diameter (25.4) (29.7) (31.5) (34.0) (38.4) (41.9) (44.5) (48.0) (52.6) (60.7)
Color Gray‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
N.P.T. Form Catalog Number*
¼ 1 — — — — — — — — — —
³⁄₈ 1 — — — — — — — — — —
½ 1 — — — — — — — — — —
½ 2 — — — — — — — — — —
½ 3 — — — — — — — — — —
¾ 2 — — — — — — — — — —
¾ 3 — — — — — — — — — —
1 4 HC1044 — — — — — — — — —
1 5 HC1047 HC1048 HC1048 HC1049 — — — — — —
1¼ 5 HC1052 HC1053 HC1053 HC1054 — — — — — —
1½ 5 HC1057 HC1058 HC1058 HC1059 — — — — — —
1½ 6 — — — HC1060 HC1062 HC1063 HC1064 — — —
2 6 — — — HC1065 HC1067 HC1068 HC1069 — — —
2 7 — — — — — — HC1070 HC1071 HC1073 HC1075
2½ 7 — — — — — — HC1076 HC1077 HC1079 HC1081
3 7 — — — — — — HC1086 HC1087 HC1089 HC1091
Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100.
‡ F5 and larger will not be color coded.
T-99
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
4 Conductors
SJ, SJO,
SJT,
Cord Type SJTO S, SO, ST, STO
Cord Size #18 #16 #14 #18 #16 #14 #12 #10 #8
Approximate .36" .39" .43" .42" .45" .61" .70" .77" .97"
Diameter (9.0) (9.8) (10.8) (10.7) (11.4) (15.5) (17.8) (19.4) (24.6)
Color White Blue Blue Blue Blue Brown Yellow Orchid Gray‡
N.P.T. Form Catalog Number*
¼ 1 HC1005 HC1006 HC1006 HC1006 — — — — —
³⁄₈ 1 HC1011 HC1012 HC1012 HC1012 — — — — —
½ 1 HC1017 HC1018 HC1018 HC1018 — — — — —
½ 2 HC1022 HC1023 HC1023 HC1023 HC1023 HC1024 — — —
½ 3 — HC1025 HC1025 HC1025 HC1025 HC1026 HC1027 HC1028 —
¾ 2 — HC1033 HC1033 HC1033 HC1033 HC1034 — — —
¾ 3 — HC1035 HC1035 HC1035 HC1035 HC1036 HC1037 HC1038
1 4 — HC1039 HC1039 HC1039 HC1039 HC1040 HC1041 HC1042 HC1043
1 5 — — — — — — — — HC1046
1¼ 5 — — — — — — — — HC1051
1½ 5 — — — — — — — — HC1056
1½ 6 — — — — — — — — —
2 6 — — — — — — — — —
2 7 — — — — — — — — —
2½ 7 — — — — — — — — —
3 7 — — — — — — — — —
Note: * Must add prefix, see Note 1; suffix, see Note 2, on page T-100.
‡ F5 and larger will not be color coded.
5 Conductors
Cord Type S, SO, ST, STO
Cord Size #18 #16 #14 #12 #10 #8 #6
Approximate .50" .54" .70" .76" .83" 1.06" 1.18"
Diameter (12.7) (13.7) (17.7) (19.3) (21.1) (26.9) (30.0)
Color Blue Brown Yellow Orchid‡ Orchid‡ Pink‡ ‡
N.P.T. Form Catalog Number*
½ 2 HC1023 HC1024 — — — — —
½ 3 HC1025 HC1026 HC1027 HC1028 HC1028 — —
¾ 2 HC1033 HC1034 — — — — —
¾ 3 HC1035 HC1036 HC1037 HC1038 HC1038 — —
1 4 HC1039 HC1040 HC1041 HC1042 HC1042 HC1044 —
1 5 — — — HC1045 HC1045 HC1047 HC1048
1¼ 5 — — — HC1050 HC1050 HC1052 HC1053
1½ 5 — — — HC1055 HC1055 HC1057 HC1058
Note * Must add prefix, see Note 1; suffix, see Note 2, on page T-100.
‡ F5 and larger will not be color coded.
Kellems® Wire Management Products
Technical Information
Cord Connectors
T-100 Dimensions in Inches (cm)
www.hubbell-wiring.com
Note:
1. Add the proper prefix to the HC number to identify
the type of connector desired:
SHC = Straight Hubbell Connector
NHC = 90° Hubbell Connector
FHC = Female Hubbell Connector
VHC = 45° Hubbell Connector
2. Add the proper suffix to identify material desired:
Aluminum = No suffix
Zinc-Plated Steel = ZP
Corrosion Resistant Nylon = CR
Stainless Steel = SS
3. This chart is a general guide to assist in the selection
of Hubbell Cord Connectors for various cord sizes.
The Hubbell Cord Connector catalog numbers selected,
have been inserted into spaces which in our judgment
represent the best cord connector which will fit the
listed cord size.
The diameters of the cords are approximate and may
vary depending on the manufacturer. It is suggested
that the appropriate cord manufacturer’s dimension
chart be consulted for exact dimensions.
4. Cable jacket may have to be stripped to allow
conductors to pass through connector body.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Cord Connectors
4 Conductors
SJ, SJO,
SJT,
Cord Type SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0
Approximate .94" 1.08" 1.17" 1.27" 1.44" 1.52" 1.65" 1.77" 1.92"
Diameter (23.8) (27.4) (29.7) (33.3) (36.6) (38.6) (41.9) (45.0) (48.8)
Color Pink‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
N.P.T. Form Catalog Number*
¼ 1 — — — — — — — — —
³⁄₈ 1 — — — — — — — — —
½ 1 — — — — — — — — —
½ 2 — — — — — — — — —
½ 3 — — — — — — — — —
¾ 2 — — — — — — — — —
¾ 3 — — — — — — — — —
1 4 HC1044 — — — — — — — —
1 5 HC1047 HC1049 HC1049 — — — — — —
1¼ 5 HC1052 HC1054 HC1054 — — — — — —
1½ 5 HC1057 HC1059 HC1059 — — — — — —
1½ 6 — HC1060 HC1060 HC1061 HC1063 HC1064 — — —
2 6 — HC1064 HC1065 HC1066 HC1068 HC1069 — — —
2 7 — — — — — HC1070 HC1071 HC1073 HC1074
2½ 7 — — — — — HC1076 HC1077 HC1079 HC1080
3 7 — — — — — HC1086 HC1087 HC1089 HC1090
Note: * Must add prefix, see Note 1; suffix, see Note 2, below.
‡ F5 and larger will not be color coded.
T-101
Dimensions in Inches (cm) www.hubbell-wiring.com
Kellems® Wire Management Products Technical Information
A
Thread Size
(N.P.S.)
C
Minimum
Thk.
B
Maximum
Diameter
A
C
B
A C
B
N.P.T. Thread Locknuts
Zinc-Plated Steel
N.P.T. A B C
Hub Inside Dia. Outside Dia. Thk. Steel
Size inches (mm) inches (mm) inches (mm) Catalog Number
½ ½"-14 1.14" (29.0) .09" (2.3) 00322001LPK50
¾ ¾"-14 1.43" (36.3) .11" (2.8) 00322002LPK50
1 1"-11½ 1.77" (45.0) .13" (3.3) 00322003LPK50
1¼ 1¼"-11½ 2.28" (57.9) .13" (3.3) 00322004LPK50
1½ 1½"-11½ 2.60" (66.0) .13" (3.3) 00322005LPK50
Metal Clad Sealing O-Rings – Sizes ½ - 4
Zinc-Plated Steel with Neoprene Ring
N.P.T. A B C
Hub Inside Dia. Outside Dia. Thk.
Size inches (mm) inches (mm) inches (mm) Catalog Number
½ .80" (20.3) 1.08" (27.4) .16" (3.2) 20509001
¾ 1.00" (25.4) 1.34" (34.0) .16" (3.2) 20509002
1 1.25" (31.6) 1.63" (41.4) .16" (3.2) 20509003
1¼ 1.61" (40.9) 2.00" (50.8) .16" (3.2) 20509004
1½ 1.84" (46.7) 2.36" (59.9) .16" (3.2) 20509005
2 2.31" (58.7) 2.83" (71.9) .16" (3.2) 20509006
Chrome Plated Steel with Neoprene Ring
2½ 2.91" (73.9) 3.44" (87.4) .24" (6.1) 20509007
3 3.52" (89.4) 4.08" (103.6) .24" (6.1) 20509008
Nylon PG Thread Locknuts
PG Thread A B C
Size inches (mm) inches (mm) inches (mm) Catalog Number
PG7 .75" (19.1) .80" (20.3) .22" (5.6) LNP7BPK100
PG9 .86" (21.8) .91" (23.2) .22" (5.6) LNP9BPK100
PG11 .94" (23.9) 1.03" (26.2) .22" (5.6) LNP11BPK100
PG13.5 1.06" (26.9) 1.14" (29.0) .24" (6.1) LNP13BPK100
PG16 1.18" (30.0) 1.30" (33.0) .25" (6.1) LNP16BPK100
PG21 1.41" (35.8) 1.54" (39.1) .25" (6.1) LNP21BPK100
PG29 1.81" (46.0) 2.00" (50.8) .25" (6.1) LNP29BPK25
PG36 2.24" (56.9) 2.50" (63.5) .25" (6.1) LNP36BPK25
Nylon Metric Thread Locknuts
PG Thread A B C
Size inches (mm) inches (mm) inches (mm) Catalog Number
M12 .75" (19.1) .82" (20.8) .22" (5.6) LNM12BPK100
M16 .87" (22.09) .98" (25.0) .22" (5.6) LNM16BPK100
M20 1.06" (27.0) 1.18" (30.0) .25" (6.4) LNM20BPK100
M25 1.38" (35.1) 1.54" (39.1) .28" (7.1) LNM25BPK100
M32 1.61" (40.9) 1.80" (45.7) .28" (7.1) LNM32BPK100
M40 1.97" (50.0) 2.18" (55.4) .28" (7.1) LNM40BPK100
Kellems® Wire Management Products
Technical Information
Locknuts and Sealing O-Rings
Dimensions shown are approximate and
are subject to change without notice.
T-102 Dimensions in Inches (cm)
www.hubbell-wiring.com
Hubbell Juniors®
Material Operating Temperature Range
Nylon (connectors and GOTCHA® rings) -40°F to +225°F (-40°C to +107°C)
Neoprene (bushings) -30°F to +240°F (-34°C to +115°C)
Due to the limiting factors of nylon and neoprene, any complete liquidtight Hubbell Junior will continuously perform in the range
of -30°F to +225°F (-34°C to +107°C).
Snap-In continuously performs -40°F to +225°F (-40°C to +107°C).
Flammability
Hubbell Juniors have a UL 94V-2 rating.
Certifications
Product Agency
Liquidtight and Liquidtight with Spiral UL Listed.
CSA Certified.
Snap-In UL Recognized.
CSA Certified.
Knockout Holes
Knockout Hole
Recommended
N.P.T. Min. to Max.
Hub Size inches (mm)
¼ .54"-.57" (13.7-14.5)
³⁄₈ .67"-.70" (17.0-17.8)
½ .86"-.91" (21.8-23.1)
Dimensions shown are approximate and
are subject to change without notice.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Hubbell Juniors® Miniature Nylon Cord Connectors
T-103
Dimensions in Inches (cm) www.hubbell-wiring.com
Dimensions shown are approximate and
are subject to change without notice.
Kellems® Wire Management Products Technical Information
B
E
F
C
D
A
B
F
G
DE
AC
G
D
F
C
B
AChassis
Thickness
Max
E
Snap-In
For
Chas. Required Dimensional
Diameter Thk. Hole Size Specifications
Range (Max.) A B C D E F G
Inches Inches Inches Inches Inches Inches Inches Inches Inches
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
.22"-.27" .10" .50" .45" .28" .28" .54" .12" 1.84"
(5.6-6.9) (2.5) (12.7) (11.4) (7.1) (7.1) (13.7) (3.0) (44.2)
.28"-.32" .10" .50" .47" .28" .33" .59" .12" 1.84"
(7.1-8.1) (2.5) (12.7) (11.9) (7.1) (8.4) (15.0) (3.0) (44.2)
.30"-.36" .13" .63" .55" .36" .37" .65" .14" 2.18"
(7.6-9.1) (3.3) (16.0) (14.0) (9.1) (9.4) (16.5) (3.6) (55.4)
.32"-.43" .13" .75" .66" .45" .44" .75" .14" 2.60"
(8.1-10.9) (3.3) (19.0) (16.8) (11.4) (11.2) (19.1) (3.6) (66.0)
Liquidtight
F A B C D E
Throat Across Across
Dia. Ref. Dia. Corners Flats
Inches Inches Inches Inches Inches Inches
N.P.T. (mm) (mm) (mm) (mm) (mm) (mm)
¼-18 .65" 1.30" .40" .29" .65" .60"
(16.5) (33.0) (10.2) (7.4) (16.5) (15.2)
³⁄₈-18 .81" 1.44" .41" .36" .81" .75"
(20.6) (36.6) (10.4) (9.1) (20.6) (19.1)
½-14 1.00" 1.56" .46" .45" .99" .92"
(25.4) (39.6) (11.7) (11.4) (25.1) (23.4)
Liquidtight with Spiral
G A B C D E F
Throat Across Across
Dia. Ref. Dia. Corners Flats
Inches Inches Inches Inches Inches Inches Inches
N.P.T. (mm) (mm) (mm) (mm) (mm) (mm) (mm)
¼-18 .65" 2.55" .40" .29" .27" .65" .60"
(16.5) (64.8) (10.2) (7.4) (6.9) (16.5) (15.2)
³⁄₈-18 .81" 3.10" .41" .36" .35" .81" .75"
(20.6) (78.7) (10.4) (9.1) (8.9) (20.6) (19.1)
½-14 1.00" 3.72" .46" .45" .45" .99" .92"
(25.4) (94.5) (11.7) (11.4) (11.4) (25.1) (23.4)
Kellems® Wire Management Products
Technical Information
Hubbell Juniors® Miniature Nylon Cord Connectors
Rigid PVC core bonded to exible PVC jacket
All nonmetallic construction ends metal fatigue and
separation problems
UL Listed and CSA Certied
Cuts cleanly with a knife or PVC cutter so there
are no jagged metal edges
T-104 Dimensions in Inches (cm)
www.hubbell-wiring.com
PolyTuff® I Conduit
Trade Size (metric designator) Feet (m) Catalog Number
³⁄₈ (12) 100 (30.5) G1038
½ (16) 100 (30.5) G1050
¾ (21) 100 (30.5) G1075
1 (27) 100 (30.5) G1100
1¼ (35) 100 (30.5) G1125
1½ (41) 50 (15.2) G1150
2 (53) 50 (15.2) G1200
Note: See pages T-68, T-69, T-107 and T-109 for approved fittings.
See pages T-110 to T-111 for additional technical data and dimensional drawings.
Kellems® Wire Management Products
PolyTuff® I Non-Metallic Liquidtight Conduit
Features and Benefits
PolyTuff® I Conduit–Gray
PolyTuff® I Non-Metallic Liquidtight Conduit Kellems® Wire Management Products
IP66
SUITABILITY
PVC core with corrugated walls bonded to PVC jacket
Handles twists, turns, bends, switchbacks and straightaways with ease
All nonmetallic construction ends fatigue and
separation problems
Can be cut with a knife or PVC cutters
UL Recognized and CSA Certied
T-105
Dimensions in Inches (cm) www.hubbell-wiring.com
PolyTuff® II Tubing
Trade Size (metric designator) Feet (m) Catalog Number
¼ (10) 100 (30.5) B2025
³⁄₈ (12) 100 (30.5) B2038
½ (16) 100 (30.5) B2050
¾ (21) 100 (30.5) B2075
1 (27) 100 (30.5) B2100
1¼ (35) 100 (30.5) B2125
1½ (41) 50 (15.2) B2150
2 (53) 50 (15.2) B2200
Note: See page T-107 for approved fittings.
See pages T-110 to T-111 for additional technical data and dimensional drawings.
Kellems® Wire Management Products
PolyTuff® II Non-Metallic Liquidtight Tubing
Features and Benefits
PolyTuff® II Tubing–Black
Kellems® Wire Management Products PolyTuff® II Non-Metallic Liquidtight Tubing
IP66
SUITABILITY
Nylon two-piece swivel body enables
tting to twist from 0° to 90°
Non-integral ferrule provides conduit seal
and superior pullout protection
Nylon compression nut
has a tapered dome to
tighten ferrule onto
conduit
Neoprene O-ring provides
liquidtight seal at hub or enclosure
Nylon locknut fastens connector
securely to enclosure and provides
superior corrosion resistance
T-106 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems® Wire Management Products
PolyTuff® Non-Metallic Liquidtight Fittings
Features and Benefits
PolyTuff® Non-Metallic Liquidtight Fittings Kellems® Wire Management Products
PS05GYKIT
P1259NGY
P125NGY
P075NGYA
PS0509NGY - SwivelLok®
T-107
Dimensions in Inches (cm) www.hubbell-wiring.com
Straight with Male Non-Metallic Liquidtight Fittings
Trade Black Gray
Size (metric designator) Catalog Number Catalog Number
¼ (6) F2025 —
³⁄₈ (9) P038NBKA P038NGYA
½ (13) P050NBKA P050NGYA
¾ (19) P075NBKA P075NGYA
1 (25) P100NBKA P100NGYA
1¼ (32) P125NBK P125NGY
1½ (38) P150NBK P150NGY
2 (51) P200NBK P200NGY
Note: Fittings are to be used with PolyTuff I and PolyTuff II.
See page T-113 for additional technical data and dimensional drawings.
³⁄₈" Liquidtight conduit fitting have ½ N.P.T. male threads.
SwivelLok® Multi-Position with Male Non-Metallic Liquidtight Fittings
Trade Black Gray
Size (metric designator) Catalog Number Catalog Number
³⁄₈ (9) PS0389NBK PS0389NGY
½ (13) PS0509NBK PS0509NGY
¾ (19) PS0759NBK PS0759NGY
1 (25) PS1009NBK PS1009NGY
Note: Fittings are to be used with PolyTuff I and PolyTuff II.
See page T-113 for additional technical data and dimensional drawings.
³⁄₈" Liquidtight conduit fitting have ½ N.P.T. male threads.
Fixed 90°Fittings for Non-Metallic Conduit
Trade Black Gray
Size (metric designator) Catalog Number Catalog Number
¼ (6) F20259 —
³⁄₈ (9) P0389NBK P0389NGY
½ (13) P0509NBK P0509NGY
¾ (19) P0759NBK P0759NGY
1 (25) P1009NBK P1009NGY
1¼ (32) P1259NBK P1259NGY
Note: Fittings are to be used with PolyTuff I and PolyTuff II.
See page T-113 for additional technical data and dimensional drawings.
³⁄₈⁄⁄" Liquidtight conduit fitting have ½ N.P.T. male threads.
SwivelLok® Flexible Conduit Kit
Trade Size (metric designator) Fitting and Conduit Catalog Number
½ (13) 2 PS0509NGY, 6' G1050 PS05GYKIT
¾ (19) 2 PS0759NGY, 6' G1075 PS07GYKIT
Note: See page T-113 for additional technical data and dimensional drawings.
Kellems® Wire Management Products
PolyTuff® Non-Metallic Liquidtight Fittings
Kellems® Wire Management Products PolyTuff® Non-Metallic Liquidtight Fittings
UL Listed to Type
4X, 12 and 13
Hexagonal, screw-machined steel thru 1", and
malleable iron on larger sizes. Nut compresses
gland-ring onto conduit
Split, nylon, gland-ring compresses
conduit onto ferrule
Non-integral, reusable steel,
ferrule is easily installed, to
seal conduit
Threaded one-piece steel body
Tapered, machined threads fasten securely and provide
additional liquidtight sealing
Optional insulated and non-insulated throat
Nylon gasket provides liquidtight seal at hub
Locknut has hardened steel tangs to grip securely
T-108 Dimensions in Inches (cm)
www.hubbell-wiring.com
Kellems® Wire Management Products
Metallic Liquidtight Conduit Fittings
Features and Benefits
Metallic Liquidtight Conduit Fittings Kellems® Wire Management Products
T-109
Dimensions in Inches (cm) www.hubbell-wiring.com
Straight Conduit Fitting
Trade Size (metric designator) Insulated Non-Insulated
³⁄₈ (9) H0381 H038
½ (13) H0501 H050
¾ (19) H0751 H075
1 (25) H1001 H100
1¼ (32) H1251 H125
1½ (38) H1501 H150
2 (51) H2001 H200
2½ (63) H2501 H250
3 (76) H3001 H300
3½ (89) H3501 H350
4 (102) H4001 H400
Note: ³⁄₈" Liquidtight conduit fitting have ½ N.P.T. male threads.
For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
See page T-114 for additional technical data.
45° Conduit Fitting
Trade Size (metric designator) Insulated Non-Insulated
³⁄₈ (9) H03841 H0384
½ (13) H05041 H0504
¾ (19) H07541 H0754
1 (25) H10041 H1004
1¼ (32) H12541 H1254
1½ (38) H15041 H1504
2 (51) H20041 H2004
Note: ³⁄₈" Liquidtight conduit fitting have ½ N.P.T. male threads.
For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
See page T-114 for additional technical data.
90° Conduit Fitting
Trade Size (metric designator) Insulated Non-Insulated
³⁄₈ (9) H03891 H0389
½ (13) H05091 H0509
¾ (19) H07591 H0759
1 (25) H10091 H1009
1¼ (32) H12591 H1259
1½ (38) H15091 H1509
2 (51) H20091 H2009
2½ (63) H25091 H2509
3 (76) H30091 H3009
4 (102) H40091 H4009
Note: ³⁄₈" Liquidtight conduit fitting have ½ N.P.T. male threads.
For use with Liquidtight Metal conduit and PolyTuff I Non-Metallic conduit.
See page T-114 for additional technical data.
Kellems® Wire Management Products
Metallic Liquidtight Conduit Fittings
Kellems® Wire Management Products Metallic Liquidtight Conduit Fittings
Straight with Male
Hubbell Conduit Fitting
H050
45° Angle with Male
Hubbell Conduit Fitting
H0504
90° Angle with Male
Hubbell Conduit Fitting
H0509
T-110 Dimensions in Inches (cm)
www.hubbell-wiring.com
PolyTuff I Conduit
Operating Temperature Range
Wet environment 0°F to +140°F (-18°C to +60°C).
Oil environment 0°F to +158°F (-18°C to +70°C).
Dry environment 0°F to +176°F (-18°C to +80°C).
Certifications
UL Listed UL Standard 1660.
Sunlight resistant approved for outdoor use, direct burial.
CSA Certified Meets requirements of NEC.
Voltage Rating
Maximum 600V.
Material
Conduit Co-extruded rigid and flexible PVC.
PolyTuff II Tubing
Operating Temperature Range
Operating environment 0°F to +140°F (-18°C to +60°C).
Certifications
UL Recognized
CSA Certified
Voltage Rating
Maximum Same as wire insulation rating.
Material
Tubing Co-extruded rigid and flexible PVC.
PolyTuff I Conduit
Trade Size
(metric Conduit ID/OD Bend Radius
designator) Inches (mm) Inches (mm)
³⁄₈ (12) .49"/.70" (12.6/17.8) 2.00" (50.8)
½ (16) .63"/.83" (16.1/21.1) 3.00" (76.2)
¾ (21) .83"/1.04" (21.1/26.4) 4.00" (101.6)
1 (27) 1.05"/1.30" (26.0/33.1) 5.00" (217.0)
1¼ (35) 1.40"/1.65" (35.4/41.8) 6.30" (158.8)
1½ (41) 1.59"/1.88" (40.3/47.8) 7.50" (190.5)
2 (53) 2.03"/2.36" (51.6/59.9) 10.00" (254.0)
PolyTuff II Tubing
Trade Size
(metric Conduit ID/OD Bend Radius
designator) Inches (mm) Inches (mm)
¼ (10) .36"/.57" (9.3/14.5) 1.50" (38.1)
³⁄₈ (12) .49"/.70" (12.6/17.8) 2.00" (50.8)
½ (16) .63"/.83" (16.1/21.1) 2.00" (50.8)
¾ (21) .83"/1.04" (21.1/26.4) 3.00" (76.2)
1 (27) 1.05"/1.30" (26.0/33.1) 3.00" (76.2)
1¼ (35) 1.40"/1.65" (35.4/41.8) 5.00" (127.0)
1½ (41) 1.59"/1.88" (40.3/47.8) 5.00" (127.0)
2 (53) 2.03"/2.36" (51.6/59.9) 5.00" (127.0)
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Conduit and Tubing
Technical Information Kellems® Wire Management Products
T-111
Dimensions in Inches (cm) www.hubbell-wiring.com
Acetate Solvents D D
Acetic Acid B C
Acetic Acid (Glacial) C D
Acetone D D
Acrylontrile A B
Alcohols (Aliphatic) C C
Aluminum Chloride A A
Aluminum Sulfate (Alums) A A
Ammonia (Anhydrous Liquids) D D
Ammonia (Aqueous) A A
Ammoniated Latex A C
Ammonium Chloride A A
Ammonium Hydroxide A A
Amyl Acetate D D
Aniline Oils D D
Aromatic Hydrocarbons D D
Asphalt D D
ASTM Fuel A C C
ASTM Fuel B D D
ASTM #1 Oil B C
ASTM #3 Oil C D
Barium Chloride A A
Barium Sulfide A A
Barium Hydroxide A A
Benzene (Benzol) D D
Benzine (Petroleum Ether) C C
Black Liquor A A
Bordeaux Mixture A A
Boric Acid A A
Butyl Acetate D D
Butyl Alcohol B C
Calcium Hydroxide A A
Calcium Hypochlorite A A
Carbolic Acid (Phenol) B C
Carbon Dioxide A A
Carbon Disulfide D D
Carbon Tetrachloride D D
Carbonic Acid A A
Casein A C
Caustic Soda A B
Chlorine Gas (wet) D D
Chlorine Gas (dry) D D
Chlorine (water solution) C D
Chlorobenzene D D
Chlorinated Hydrocarbons D D
Chromic Acid B C
Citric Acid A A
Coal Tar D D
Coconut Oil C D
Corn Oil A B
Cottonseed Oil C D
Creosote D D
Cresol C D
Crysylic Acid D D
Cyclohexane B C
DDT Weed Killer A C
Dibutyl Phthalate D D
Diesel Oils C D
Diethylene Glycol B C
Diethyl Ether A C
Di-isodecyl Phthalate D D
Dioctyl Phthalate D D
Dow General Weed Killer (Phenol) D D
Dow General Weed Killer (H2O) B C
Ethyl Alcohol C C
Ethylene Dichloride D D
Ethylene Glycol B C
Ferric Chloride A A
Ferric Sulfate A A
Ferrous Chloride A A
Ferrous Sulfate A A
Formaldehyde D D
Fuel Oil B C
Furfural C C
Gallic Acid A A
Gasoline (Hi Test) C D
Glycerine A A
Grease A C
Green Sulfate Liquor A A
Heptachlor in Petroleum Solvents A C
Heptane C D
Hexane C D
Hydrobromic Acid A A
Hydrochloric Acid 10% A A
Hydrochloric Acid 40% C C
Hydrofluoric Acid 70% D D
Hydrofluorosilicic Acid A A
Hydrofluorosilicic Acid 10% A A
Hydrogen Peroxide A B
Iso-Octane C C
Isopropyl Acetate D D
Isopropyl Acid B C
Jet Fuels (JP-3, and 5) C D
Kerosene C C
Ketones D D
Linseed Oil A A
Lubricating Oils A A
Magnesium Chloride A A
Magnesium Hydroxide A A
Magnesium Sulfate A A
Malathion 50 in Aromatics D D
Malic Acid A A
Methyl Acetate D D
Methyl Alcohol C C
Methyl Bromide D D
Methyl Ethyl Ketone D D
Methylene Chloride D D
Mineral Oil
Monochlorobenezene A A
Muriatic Acid (see Hydrochloric Acid)
Naphtha C D
Naphthalene D D
Nitric Acid 10% A B
Nitric Acid 35% A C
Nitric Acid 70% D D
Oleic Acid A C
Oleum D D
Oxalic Acid A A
Pentachlorophenol in Oil B C
Pentane C D
Perchloroethylene B C
Petroleum Ether C C
Phenol A A
Phosphoric Acid 10% A A
Pitch 50% A B
Potassium Hydroxide C D
Sodium Cyanide A A
Stoddard Solvent D D
Styrene D D
Sulfur Dioxide (liquid) D D
Sulfuric Acid 50% A B
Sulfuric Acid 98% D D
Sulfurous Acid B C
Tall Oil D D
Tannic Acid A A
Toluene D D
Trichlorethylene D D
Triethanol Amine C D
Tricresyl Phosphate (Skydrol) D D
Turpentine C D
Vinegar A B
Vinyl Chloride D D
Water A A
White Liquor A A
Xylene D D
Zinc Chloride A A
Zinc Sulfate A A
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Conduit and Tubing
PolyTuff I and II Conduit/Tubing; PVC Chemical Resistance
Temp. Temp. Temp.
Chemical Conc* 70°F 150°F Chemical Conc* 70°F 150°F Chemical Conc* 70°F 150°F
21°C 66°C 21°C 66°C 21°C 66°C
Kellems® Wire Management Products Technical Information
Note: * Conc. - Concentration.
(All ratings apply to concentrated or saturated solutions unless otherwise specified.)
Chemical resistance ratings are based upon information supplied by the raw material manufacturers.
Use as a general guide only – samples should be tested by user under actual conditions.
Rating Code
A-Excellent service
No harmful effect to reduce service life. Suitable for
continuous service.
B-Good service life.
Moderate to minor effect. Good for intermittent service.
Generally suitable for continuous service.
C-Fair or limited service.
Depends on operating conditions. Generally suitable for
intermittent service. Not recommended for continuous service.
D-Unsatisfactory service.
Not recommended.
T-112 Dimensions in Inches (cm)
www.hubbell-wiring.com
PolyTuff Fittings
Operating Temperature*
Nylon (Body, Nut, Gripping Ring and Locknut) –40°F to +225°F (–40°C to +107°C).
Neoprene (Sealing Ring) –30°F to +240°F (–34°C to +116°C).
Flammability
Fire Gas Toxicity Product Testing Nylon PolyTuff Fittings have a UL 94V-2 rating.
Certifications
UL Listed UL50 Type 4X, 12 and 13.
CSA Certified PolyTuff I Fittings, Poly Tuff II Fittings.
Liquidtight Fittings
Operating Temperature**
Steel/Malleable Iron (Nut, Body, Ferrule) –60°F to +1000°F (–51°C to +538°C).
Nylon (Gland Ring) –40°F to +225°F (–40°C to +107°C).
Hazardous Locations - NEC Reference
Class I, Div. 2 - 501-10(A)(3)B
Class II, Div. 1 - 502-10(A)(2)
Class II, Div. 2 - 502-10(A)(3)
Class III, Div. 1 - 503-10(A)(2)
Class III, Div. 2 - 503-10(B)
Certifications
UL Listed
CSA Certified
Note: * Due to the limiting factors of nylon and neoprene, PolyTuff Fittings will continuously perform in the range –30°F to +225°F (–34°C to +107°C).
** Due to the limiting factors of nylon, metallic liquidtight flexible conduit fittings will continuously perform in the range of –40°F to +225°F (–40°C to +107°C).
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Fittings
45° Position
D
A
G
90° Position
F
EB
C
Straight Position
A
Dia.
B
D
C
E
Sizes: 3/8", ½", ¾", 1"
A
C
E
B
D
Sizes: ¼", 1¼", 1½", 2"
A
Dia.
C
E
B
D
T-113
Dimensions in Inches (cm) www.hubbell-wiring.com
Straight with Male Non-Metallic Liquidtight Fittings
Trade A B C D E
Size Throat
(md**) Dia. A/C* A/F*
¼ .93" 1.45" .39" .32" .86" (Dia.)
(10) (23.6) (36.8) (9.9) (8.1) (21.8)
³⁄₈ 1.14" 1.63" .57" .42" 1.41" 1.30"
(12) (29.0) (41.4) (14.5) (10.7) (35.8) (33.0)
½ 1.30" 2.14" .57" .55" 1.41" 1.30"
(16) (33.0) (54.4) (14.5) (14.0) (35.8) (33.0)
¾ 1.53" 2.22" .58" .74" 1.85" 1.53"
(21) (38.9) (56.4) (14.7) (18.8) (47.0) (38.9)
1 1.80" 2.32" .72" .96" 1.94" 1.80"
(27) (45.7) (58.9) (18.3) (24.4) (49.3) (45.7)
1¼ 2.20" 2.15" .74" 1.30" 2.38" 2.18"
(35) (55.9) (54.6) (18.8) (33.0) (60.5) (55.4)
1½ 2.49" 2.35" .76" 1.46" 2.63" 2.43"
(41) (63.2) (59.7) (19.3) (37.1) (66.8) (61.7)
2 3.05" 2.51" .79" 1.90" 3.13" 2.93"
(53) (77.4) (63.6) (20.1) (48.3) (79.5) (74.4)
Note: * A/C = Across Corners A/F = Across Flats.
** md = metric designator.
90° with Male Non-Metallic Liquidtight Fittings
Trade A B C D E
Size Throat
(md**) Dia. A/C* A/F*
¼ .93" 1.88" .39" .32" .86"(Dia.)
(10) (23.6) (47.8) (9.9) (8.1) (21.8)
1¼ 2.21" 3.57" .74" 1.30" 2.38" 2.18"
(35) (56.1) (90.7) (18.9) (33.0) (60.5) (55.4)
Note: * A/C = Across Corners A/F = Across Flats.
** md = metric designator.
SwivelLok® Multi-Position Liquidtight Fittings
Trade A B C D E F G
Size
(md**) A/C* A/F*
³⁄₈ 1.30" 3.27" .57" .55" 1.43" 2.00" 1.41" 1.30"
(12) (33.0) (83.1) (14.5) (14.0) (36.3) (50.8) (35.8) (33.0)
½ 1.30" 3.27" .57" .55" 1.43" 2.00" 1.41" 1.30"
(16) (33.0) (83.1) (14.5) (14.0) (36.3) (50.8) (35.8) (33.0)
¾ 1.53" 3.66" .58" .74" 1.59" 2.23" 1.65" 1.53"
(21) (38.9) (93.0) (15.7) (18.8) (40.4) (56.6) (41.9) (38.9)
1 1.80" 4.00" .72" .96" 1.84" 2.30" 1.94" 1.80"
(27) (45.7) (101.6) (18.3) (24.4) (46.7) (58.4) (49.3) (45.7)
Note: * A/C = Across Corners A/F = Across Flats.
** md = metric designator.
Kellems® Wire Management Products Technical Information
Kellems® Wire Management Products
Technical Information
Non-Metallic Liquidtight Fittings
A
E
Throa
t
Dia.
B
D
C
F
D
Throa
t
Dia.
E
C
A
B
Ref.
B
E
Throat
Dia.
D
C
A
F
T-114 Dimensions in Inches (cm)
www.hubbell-wiring.com
Straight with Male Metallic Metal Fitting
Trade Size A B C D E
(md**) Ref. A/C* A/F* Throat Dia. A/C* A/F*
³⁄₈ 1.43" .59" 1.20" 1.06" .61" 1.07" .93"
(12) (36.3) (15.0) (30.0) (26.9) (15.5) (27.2) (23.6)
½ 1.43" .59" 1.34" 1.19" .61" 1.22" 1.06"
(16) (36.3) (15.0) (34.0) (30.2) (15.5) (31.0) (26.9)
¾ 1.56" .59" 1.55" 1.37" .84" 1.43" 1.25"
(21) (39.6) (15.0) (39.0) (34.8) (21.3) (36.3) (31.8)
1 1.68" .66" 1.95" 1.69" 1.06" 1.73" 1.56"
(27) (42.7) (16.8) (50.0) (42.9) (26.9) (43.9) (39.6)
1¼ 2.03" .63" 2.39" 2.06" 1.37" 2.36" 2.08"
(35) (51.6) (16.8) (61.0) (52.3) (34.8) (59.9) (52.8)
1½ 2.21" .63" 2.72" 2.38" 1.53" 2.79" 2.48"
(41) (56.1) (16.8) (69.0) (60.5) (38.9) (70.9) (63.0)
2 2.28" .69" 3.08" 2.87" 2.06" 3.32" 2.90"
(53) (57.9) (17.5) (78.0) (72.9) (52.3) (84.3) (73.7)
2½ 3.56" 1.06" 3.92" 3.62" 2.42" 3.85" 3.60"
(63) (90.4) (26.9) (100.0) (91.9) (61.5) (97.8) (91.4)
3 3.81" 1.06" 4.70" 4.31" 3.01" 4.65" 4.33"
(78) (96.8) (26.9) (119.0) (109.5) (76.5) (118.1) (110.0)
3½ 3.81" 1.06" 5.29" 4.81" 3.49" 5.18" 4.82"
(91) (96.8) (26.9) (134.0) (122.2) (88.6) (131.6) (122.4)
4 3.81" 1.06" 5.75" 5.31" 3.96" 5.75" 5.39"
(103) (96.8) (26.9) (146.0) (134.9) (100.6) (146.1) (136.9)
45° with Male Metallic Metal Fitting
Trade Size A B C D E F
(md**) A/C* A/F* Throat Dia. A/C* A/F*
³⁄₈ 1.19" 1.28" .59" 1.20" 1.06" .60" 1.16" 1.02"
(12) (30.2) (32.5) (15.0) (30.5) (26.9) (15.2) (29.5) (25.9)
½ 1.19" 1.28" .59" 1.34" 1.19" .61" 1.21" 1.06"
(16) (30.2) (32.5) (15.0) (34.0) (30.2) (15.2) (30.7) (26.9)
¾ 1.19" 1.43" .59" 1.55" 1.45" .84" 1.50" 1.32"
(21) (30.2) (36.3) (15.0) (39.4) (36.8) (21.3) (38.1) (33.5)
1 1.38" 1.53" .66" 1.95" 1.69" 1.05" 1.82" 1.59"
(27) (35.1) (38.9) (16.8) (49.5) (42.9) (26.7) (46.2) (40.4)
1¼ 1.42" 1.69" .63" 2.39" 2.06" 1.37" 2.32" 2.03"
(35) (36.1) (42.9) (16.0) (60.7) (52.3) (34.8) (58.9) (5.16)
1½ 1.66" 2.00" .66" 2.72" 2.38" 1.60" 2.62" 2.29"
(41) (42.2) (50.8) (16.8) (69.1) (60.5) (40.6) (66.5) (58.2)
2 1.69" 2.25" .66" 3.08" 2.88" 2.05" 3.21" 2.80"
(53) (42.9) (57.2) (16.8) (78.2) (73.2) (52.1) (81.5) (71.1)
90° with Male Metallic Metal Fitting
Trade Size A B C D E F
(md**) A/C* A/F* Ref. Throat Dia. A/C* A/F*
³⁄₈ 1.31" .59" 1.20" 1.06" 1.44" .60" 1.13" .99"
(12) (33.3) (15.0) (30.5) (26.9) (36.6) (15.2) (29.0) (25.1)
½ 1.31" .59" 1.34" 1.12" 1.44" .61" 1.12" 1.00"
(16) (33.3) (15.0) (34.0) (28.4) (36.6) (15.5) (28.0) (25.4)
¾ 1.44" .59" 1.55" 1.45" 1.63" .83" 1.48" 1.29"
(21) (36.6) (15.0) (39.4) (36.8) (41.4) (21.1) (38.0) (32.8)
1 1.78" .59" 1.95" 1.60" 2.19" 1.05" 1.80" 1.57"
(27) (45.2) (15.0) (49.5) (40.6) (55.6) (26.7) (46.0) (39.9)
1¼ 1.97" .63" 2.39" 2.06" 2.50" 1.36" 2.32" 2.02"
(35) (50.0) (16.0) (60.7) (52.3) (63.5) (34.5) (59.0) (51.3)
1½ 2.19" .63" 2.72" 2.38" 2.69" 1.61" 2.58" 2.25"
(41) (55.6) (16.0) (69.1) (60.5) (68.3) (40.9) (66.0) (57.2)
2" 2.53" .66" 3.08" 2.87" 3.25" 2.05" 3.14" 2.75"
(53) (64.3) (16.8) (78.2) (72.9) (82.6) (52.1) (80.0) (69.9)
2½ 3.44" 1.00" 3.92" 3.63" 4.25" 2.42" 3.78" 3.50"
(63) (87.4) (25.4) (99.6) (92.2) (108.0) (61.5) (96.0) (88.9)
3 3.75" 1.00" 4.70" 4.31" 4.87" 3.01" 4.64" 4.30"
(78) (95.3) (25.4) (119.4) (109.5) (123.7) (76.5) (118.0) (109.2)
4 4.25" 1.00" 5.75" 5.31" 5.63" 3.96" 5.76" 5.38"
(103) (108.0) (25.4) (146.1) (134.9) (143.0) (100.6) (146.0) (136.7)
Note: * A/C = Across Corners A/F = Across Flats.
** md = metric designator.
Technical Information Kellems® Wire Management Products
Kellems® Wire Management Products
Technical Information
Metallic Liquidtight Fittings