6-9
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
6
5mm
LED CBI
®
Circuit Board Indicator
Top View, Single
550-xx04
B
2.54
[.100]
RECOMMENDED
P.C. HOLE
PATTERN
2.54
[.100]
2.54
[.100]
6.10
[.240]
6.10
[.240]
2.54
[.100]
5.84
[.230] 3.68
[.145]
A
CATHODE
Red Cathode for
Red/Green Bi-Color
Yellow Cathode for
Yellow/Green Bi-Colo
r
CATHODE
2.54
[.100]
3.43 [.135] for -0204 to -0404, 5.0 [.197] for all others
.635 [.025] for -0504 to -0704, .508 [.020] for all others
Hole diameter: 1.22 [.048] for .635 [.025], 1.02 [.040] for all others
A
B
PART NO. COLOR
GENERAL PURPOSE
550-0204 Green
550-0304 Yellow
550-0404 Red
INTEGRAL RESISTOR
550-0504 Red, 5V
550-0704 Green, 5V
550-0804 Yellow, 5V
LOW CURRENT
550-1104 Red
550-1204 Yellow
550-1304 Green
HIGH EFFICIENCY
550-2204 Green
550-2304 Yellow
550-2404 Red
550-2504 Orange
BI-COLOR
550-3004 Red/Green
550-3104 Yellow/Green
SUPER BRIGHT, DIFFUSED
550-5104 Red
550-5204 Green
550-5304 Yellow
SUPER BRIGHT, WATER CLEAR
(Non-tinted, Non-diffused)
550-5504 Red
550-5604 Green
550-5704 Yellow
Features
• Multiple CBIs form horizontal LED arrays on 6.35mm
(0.250”) center-lines.
• High Contrast, UL 94 V-0 rated, black housing
• Oxygen index: 32%
• Polymer content: PBT, 0.160 g
• Housing stand-offs facilitate PCB cleaning
• Solderability per MIL-STD-202F, method 208F
• LEDs are safe for direct viewing per IEC 825-1, EN-60825-1
• Compatible with:
550-xx04-004 quad block
Custom
• For custom LEDs contact factory.
Tolerance note: As noted, otherwise:
• LED Protrusion: ±0.04 mm [±0.016]
• CBI Housing: ±0.02mm[±0.008]
Dimensions in mm [inches]
550 x x 0 4 0 1 0
Reverse Polarity Option
1) Cathode Opposite Side
of notch
–010 Ordering Code Suffix required ONLY for Reverse Polarity Option
LED Type
PART NUMBER ORDERING CODE
Standard Polarity shown in drawing: Cathode same side as notch
Series
To order any of the 550-xx04 part numbers with Reverse
Polarity (Cathode opposite side of notch), please add -010
to the part numbers shown above.
– –
NEW
6-10
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
550-xx04
Peak I
V
V
F
Test Viewing LED
Part Number Color Wavelength nm mcd Volts Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-0204 Green 565 12.3 2.1 20 60° 5ND-9674 6-51
550-0304 Yellow 585 12.3 2.1 20 60° 5ND-9673 6-51
550-0404 Red 635 12.3 2 20 60° 5ND-9672 6-51
GENERAL PURPOSE
See page 6-55 and 6-56 for Reference Only LED Drive Circuit Examples. See page 6-57 for Pin Out
Peak I
V
V
F
Test Viewing LED
Part Number Color Wavelength nm mcd Volts Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-5504 Red 635 125 2.2 20 24° 521-9464 6-47
550-5604 Green 565 120 2.3 20 24° 521-9465 6-47
550-5704 Yellow 583 140 2.2 20 24° 521-9466 6-47
SUPER BRIGHT, WATER CLEAR (NON-TINTED, NON-DIFFUSED)
Peak I
V
V
F
Test Viewing LED
Part Number Color Wavelength nm mcd Volts Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-1104 Red 635 2 1.8 2 50° 521-9320 6-42
550-1204 Yellow 583 1.8 1.9 2 50° 521-9321 6-42
550-1304 Green 565 1.8 1.8 2 50° 521-9327 6-42
LOW CURRENT
Peak I
V
V
F
Test Viewing LED
Part Number Color Wavelength nm mcd Volts Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-2204 Green 563 10 2.1 10 65° 5HD-9270-5 6-49
550-2304 Yellow 585 6.3 2.1 10 50° 5HD-9271-5 6-49
550-2404 Red 650 7 2.2 10 50° 5HD-9269 6-49
550-2504 Orange 600 7 1.9 10 60° 521-9704 6-43
HIGH EFFICIENCY
Peak I
V
V
F
Test Viewing LED
Part Number Color Wavelength nm mcd Volts Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-5104 Red 650 34 2.1 20 50° 5SD-9441 6-53
550-5204 Green 563 34 2.2 20 50° 5SD-9456 6-53
550-5304 Yellow 585 34 2.2 20 50° 5SD-9455 6-53
SUPER BRIGHT, DIFFUSED
Peak I
V
V
F
Test Viewing LED
Part Number Color Wavelength nm mcd Volts Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-3004 Red/Green 660/565 90/40 1.8/2.1 20 60° 521-9651 6-46
550-3104 Yellow/Green 585/565 8.7/8.7 2.1/2.1 20 50° 521-9724 6-46
BI-COLOR
Peak I
V
Test Forward Viewing LED
Part Number Color Wavelength nm mcd Voltage Current (mA) Angle 2
ΘΘ½
Data sheet Page #
550-0504 Red 655 2 5 13 60° 5RD-9422 6-52
550-0704 Green 565 8 5 12 60° 5RD-9423 6-52
550-0804 Yellow 583 8 5 10 60° 521-9284 6-41
INTEGRAL RESISTOR
Typical Operating Characteristics (TA=25°C)
See LED data sheet for additional information
Red Yellow
ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9183 -9284
Forward Voltage (V) 7.5 7.5
Derating (V/°C) From 50°C .071 .071
Operating Temperature (°C) -40/+85 -40/+85
Storage Temperature (°C) -55/+100 -55/+100
Soldering Temperature 260°C, 5 seconds, 1.6 mm from case
6-41
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
6
5mm Discrete LED
Integral Resistor, 5 Volts
Diffused
9.19 [.362]
8.43 [.332] .76
[.030]
25.1 [1.00]
MIN
1.27
[.050]
.64
[.025]
5.84
[.230]
2.54
[.100
]
CATHODE
1.0
[.040]
MAX
1.0
[.040]
MAX
5.08 [.200]
4.57 [.180]
PART NO. LED COLOR
521-9183 Red
521-9284 Yellow
Dimensions in mm [inches]
MOUNTING CLIP: 515-0004
located on page 6-48
Red Yellow
OPERATING CHARACTERISTICS (TA=25°C) -9183 -9284
Luminous Intensity (mcd) Min. 2 2
VF= 5V Typical 8 8
Peak Wavelength (nm) Typical 635 583
λ Peak
Viewing Angle (2Θ ½) Typical 60° 60°
Forward Current (I) Typical 10 10
VF = 5V Max 15 15
Reverse Voltage (V), IR=100µA Min. 5 5
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
521-9183, -9284
6-42
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
Red Yellow Green
ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9320 -9321 -9327
Power Dssipation (mW) 27 36 24
Derating (mA/°C)
From 92°C
111
Forward Current (mA) 7 7 7
Peak Current (mA) 500 500 500
Pulse width = 10 µs
Operating Temperature (°C) -55/+100 -55/+100 -55/+100
Storage Temperature (°C) -55/+100 -55/+100 -55/+100
Soldering Temperature 260°C, 5 seconds, 1.6 mm from case
5mm Discrete LED
Low Current, 2mA
Diffused
521-9320, -9321, -9327
8.81 [.347] .76
[.030]
25.1 [1.00]
MIN
1.27
[.050]
4.83
[.190]
.46
[.018]
5.84
[.230]
2.54
[.100]
CATHODE
1.0
[.040]
MAX
1.0
[.040]
MAX
PART NO. COLOR
521-9320 Red
521-9321 Yellow
521-9327 Green
Red Yellow Green
OPERATING CHARACTERISTICS (TA=25°C) -9320 -9321 -9327
Luminous Intensity (mcd) Min. 1.2 1.2 1.2
IF=2mA Typical 2 1.8 1.8
Peak Wavelength (nm) Typical 635 583 565
λ Peak
Viewing Angle (2Θ ½) Typical 50° 50° 50°
Forward Voltage (V) Typical 1.8 1.9 1.8
IF=2mA Max. 2.2 2.7 2.2
Reverse Voltage (V), IR=50µA Min. 5 5 5
Dimensions in mm [inches] MOUNTING CLIP: 515-0004
located on page 6-48
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
6-46
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
5mm Discrete LED
Bi-Color
Non-Tinted, Diffused
521-9651, -9724
5.00
[.197]
8.64[.340]
22.1 [.87]
MIN.
0.51
[.020]
CATHODE
GREEN,
RED/GREEN
BI-COLOR
521-9651
CATHODE
YELLOW,
YELLOW/GREEN
BI-COLOR
521-9724
1.00
[.04]
5.59
[.220]
2.54
[.100]
1.50
[.059]
MAX
PART NO. LED COLOR
521-9651 Red/Green
521-9724 Yellow/Green
Red/Green Yellow/Green
ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9651 -9724
Power Dissipation (mW) 100/100 60/100
Forward Current (mA) 40/30 20/30
Derating (mA/°C)
From 50°C
.5/.4 .25/.40
Peak Current (mA) 200/120 80/120
Pulse width = 100 µs
Operating Temperature (°C) -55/+100 -55/+100
Storage Temperature (°C) -55/+100 -55/+100
Soldering Temperature 260°C, 5 seconds, 1.6 mm from case
Red/Green Yellow/Green
OPERATING CHARACTERISTICS (TA=25°C) -9651 -9724
Luminous Intensity (mcd) Min. 29/12.6 2.5/2.5
IF=20mA Typical 90/40 8.7/8.7
Peak Wavelength (nm) Typical 660/565 585/565
λ Peak
Viewing Angle (2Θ ½) Typical 60° 50°
Forward Voltage (V) Typical 1.8/2.1 2.1/2.1
IF=20mA Max. 2.4/2.8 2.8/2.8
Dimensions in mm [inches]
MOUNTING CLIP: 515-0005
located on page 6-48
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
6-47
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
6
5mm Discrete LED
Super Bright, Water Clear
Non-Tinted, Non-Diffused
521-9464,-9465,-9466
8.81 [.347]
4.83
[.190]
25.35 [.998]
MIN
1.27
[.050]
TYP
2.54
[.100]
.46
[.018] SQ.
CATHODE
5.84
[.230]
1.0
[.040]
MAX
PART NO. COLOR
521-9464 Red
521-9465 Green
521-9466 Yellow
Red Green Yellow
ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9464 -9465 -9466
Power Dissipation (mW) 135 135 85
Derating (mW/°C)
From 25°C 1. From 50 °C
1.8 1.8 1.61
Forward Current (mA) 30 30 20
Peak Current (mA) 500 500 500
Pulse width = 10 µs
Operating Temperature (°C) -55/+100 -20/+100 -55/+100
Storage Temperature (°C) -55/+100 -55/+100 -55/+100
Soldering Temperature 260 °C, 5 seconds, 1.6 mm from case
Red Green Yellow
OPERATING CHARACTERISTICS (TA=25°C) -9464 -9465 -9466
Luminous Intensity (mcd) Min. 80 80 80
IF=20mA Typical 125 120 140
Peak Wavelength (nm) Typical 635 565 583
λ Peak
Viewing Angle (2Θ ½) Typical 24° 24° 24°
Forward Voltage (V) Typical 2.2 2.3 2.2
IF=20mA Max. 3 3 3
Reverse Voltage (V), IR=100µA Min. 5 5 5
Dimensions in mm [inches] MOUNTING CLIP: 515-0004
located on page 6-48
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
6-49
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
6
OPERATING CHARACTERISTICS Red Green Green Yellow Yellow
(TA=25°C) -9269 -9270-2 -9270-5 -9271-2 -9271-5
Luminous Intensity (mcd) Min. 2.2 4 3.6 4 2.2
IF=10mA Typical 7 32 10 10 6.3
Peak Wavelength (nm) Typical 650 565 563 590 585
λ Peak
Viewing Angle (2Θ ½) Typical 50° 50° 65° 70° 50°
Forward Voltage (V) Typical 2.2 2* 2.1 2.4* 2.1
IF=10mA, *IF=20mA Max. 2.5 2.6* 3 3* 3
Reverse Voltage (V), Min. 5 5* 3* 5* 3
IR=100µA *IR=10µA
ABSOLUTE MAXIMUM RATINGS Red Green Green Yellow Yellow
(TA=25°C) -9269 -9270-2 -9270-5 -9271-2 -9271-5
Power Dissipation (mW) 60 140 75 200 60
Derating (mW/°C)
From 50°C 1. From 40°C
.661.661.661
Forward Current (mA) 20 40 25 60 20
Derating (mA/°C)
From 25°C
.6 .8
Peak Current (mA) 60 500 60 1000 60
Pulse width = 1µs
Operating Temperature (°C) -25/+85 -55/+100 -25/+85 -55/+100 -25/+85
Storage Temperature (°C) -30/+100 -55/+100 -30/+100 -55/+100 -30/+100
Soldering Temperature 260°C, 5 seconds, 1.6 mm from case
5mm
High Efficiency
Diffused
5HD-xxxx
TYPE COLOR
*5HD-9269 Red
*5HD-9270-2 Green
*5HD-9270-5 Green
*5HD-9271-2 Yellow
*5HD-9271-5 Yellow
* NOT A VALID PART
NUMBER. THIS SHEET IS FOR
REFERENCE ONLY.
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
6-51
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
6
5mm
General Purpose
Diffused
5ND-xxxx
TYPE COLOR
*5ND-9672 Red
*5ND-9673 Yellow
*5ND-9674 Green
Red Yellow Green
ABSOLUTE MAXIMUM RATINGS (TA=25°C) -9672 -9673 -9674
Power Dissipation (mW) 80 60 100
Forward Current (mA) 40 20 30
Derating (mA/°C)
From 25°C
.5 .25 .4
Peak Current (mA) 200 80 120
Pulse width = 10 µs
Operating Temperature (°C) -55/+100 -55/+100 -55/+100
Storage Temperature (°C) -55/+100 -55/+100 -55/+100
Soldering Temperature 260°C, 5 seconds, 1.6 mm from case
Red Yellow Green
OPERATING CHARACTERISTICS (TA=25°C) -9672 -9673 -9674
Luminous Intensity (mcd) Min. 3.5 3.5 3.5
IF=20mA Typical 12.3 12.3 12.3
Peak Wavelength (nm) Typical 635 585 565
λ Peak
Viewing Angle (2Θ ½) Typical 60° 60° 60°
Forward Voltage (V) Typical 2 2.1 2.1
IF=20mA Max. 2.8 2.8 2.8
Reverse Voltage (V), IR=100µA Min. 5 5 5
* NOT A VALID PART
NUMBER. THIS SHEET IS FOR
REFERENCE ONLY.
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
6-52
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com
ABSOLUTE MAXIMUM RATINGS Green 12V Yellow 12V Red 5V Green 5V
(TA=25°C) -9378 -9379 -9422 -9423
Forward Voltage (V) 15* 15 7.5 7.5
*(TA=70°C)
Operating Temperature (°C) -20/+85 -40/+85 -40/+85 -20/+85
S torage Temperature (°C) -55/+100 -55/+100 -55/+100 -55/+100
Soldering Temperature 260°C, 5 seconds, 1.6 mm from case
OPERATING CHARACTERISTICS Green 12V Yellow 12V Red 5V Green 5V
(TA=25°C) -9378 -9379 -9422 -9423
Luminous Intensity (mcd) Min. 1.5* 1.5* 1 2
VF=5V, *VF=12V Typical 4* 4* 2 8
Peak W avelength (nm) T ypical 565 583 655 565
λ Peak
Viewing Angle (2Θ ½) Typical 60° 60° 60° 60°
Forward Current (mA), VF=5V Typical 13* 13* 13 12
*VF=12V Max. 20* 20* 20 15
Reverse Voltage (V), IR=100µA Typical 5 5 5 5
5mm
Integral Resistor
Diffused
5RD-xxxx
TYPE COLOR VOLTS
*5RD-9378 Green 12
*5RD-9379 Yellow 12
*5RD-9422 Red 5
*5RD-9423 Green 5
* NOT A VALID PART
NUMBER. THIS SHEET IS FOR
REFERENCE ONLY.
Θ
is the off axis angle at which the luminous intensity is half the axial luminous intensity
Solder Adherence per MIL-STD-202E, Method 208C
