EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet The Mighty Gecko family of SoCs is part of the Wireless Gecko multi-protocol portfolio. The EFR32MG1x632 and EFR32MG1x732 Mighty Gecko ICs integrate a 512 kB serial flash in the package to support over the air updates. This 5x5 QFN32 package is ideal for space constrained products that need to support ZigBee, Thread, BLE and proprietary networks. Mighty Gecko applications include: KEY FEATURES * 32-bit ARM(R) Cortex(R)-M4 core with 40 MHz maximum operating frequency * Scalable Radio configuration options available in QFN32 package * 512 kB co-packaged serial flash for over the air updates * 12-channel Peripheral Reflex System enabling autonomous interaction of MCU peripherals * Connected Home * Lighting * Home and Building Automation and Security * Autonomous Hardware Crypto Accelerator and Random Number Generator * Integrated 2.4 GHz balun and PA with up to 19.5 dBm transmit power * 125 C operating temperature ideal for connected lighting applications Core / Memory ARM CortexTM M4 processor with DSP extensions and FPU Flash Program Memory Serial Flash Memory Clock Management Memory Protection Unit RAM Memory Debug Interface DMA Controller Energy Management Other High Frequency Crystal Oscillator High Frequency RC Oscillator Voltage Regulator Voltage Monitor CRYPTO Low Frequency RC Oscillator Auxiliary High Frequency RC Oscillator DC-DC Converter Power-On Reset CRC Low Frequency Crystal Oscillator Ultra Low Frequency RC Oscillator Brown-Out Detector 32-bit bus Peripheral Reflex System RFSENSE Serial Interfaces FRC DEMOD LNA PGA IFADC I/O Ports Timers and Triggers External Interrupts Timer/Counter Protocol Timer ADC Low Energy UARTTM General Purpose I/O Low Energy Timer Watchdog Timer Analog Comparator Q I2C Pin Reset Pulse Counter Real Time Counter and Calendar IDAC AGC Frequency Synthesizer RAC PA Analog I/F USART RF Frontend CRC BALUN I BUFC Radio Transceiver MOD Pin Wakeup Cryotimer Lowest power mode with peripheral operational: EM0--Active EM1--Sleep silabs.com | Smart. Connected. Energy-friendly. EM2--Deep Sleep EM3--Stop EM4--Hibernate EM4--Shutoff Rev. 1.0 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Feature List 1. Feature List The EFR32MG1 highlighted features are listed below. * Low Power Wireless System-on-Chip. * High Performance 32-bit 40 MHz ARM Cortex(R)-M4 with DSP instruction and floating-point unit for efficient signal processing * 256 kB flash program memory * 512 kB integrated serial flash memory * 32 kB RAM data memory * 2.4 GHz radio operation * TX power up to 19.5 dBm * Low Energy Consumption * 8.7 mA RX current at 2.4 GHz (1 Mbps GFSK) * 9.8 mA RX current at 2.4 GHz (250 kbps O-QPSK DSSS) * 8.2 mA TX current @ 0 dBm output power at 2.4 GHz * 63 A/MHz in Active Mode (EM0) * 5.5 A EM2 DeepSleep current (full RAM retention and RTCC running from LFXO) * 5.1 A EM3 Stop current (State/RAM retention) * Wake on Radio with signal strength detection, preamble pattern detection, frame detection and timeout * High Receiver Performance * -92.5 dBm sensitivity @ 1 Mbit/s GFSK * -99 dBm sensitivity @ 250 kbps O-QPSK DSSS * Supported Modulation Format * 2-FSK / 4-FSK with fully configurable shaping * Shaped OQPSK / (G)MSK * Supported Protocols: * Bluetooth Smart * ZigBee(R) * Thread * 2.4 GHz Proprietary Protocols * Support for Internet Security * General Purpose CRC * Random Number Generation * Hardware Cryptographic Acceleration for AES 128/256, SHA-1, SHA-2 (SHA-224 and SHA-256) and ECC silabs.com | Smart. Connected. Energy-friendly. * Wide selection of MCU peripherals * 12-bit 1 Msps SAR Analog to Digital Converter (ADC) * 2x Analog Comparator (ACMP) * Digital to Analog Current Converter (IDAC) * Up to 16 pins connected to analog channels (APORT) shared between Analog Comparators, ADC, and IDAC * Up to 16 General Purpose I/O pins with output state retention and asynchronous interrupts * 8 Channel DMA Controller * 12 Channel Peripheral Reflex System (PRS) * 2x16-bit Timer/Counter * 3 + 4 Compare/Capture/PWM channels * 32-bit Real Time Counter and Calendar * 16-bit Low Energy Timer for waveform generation * 32-bit Ultra Low Energy Timer/Counter for periodic wake-up from any Energy Mode * 16-bit Pulse Counter with asynchronous operation * Watchdog Timer with dedicated RC oscillator @ 50nA * Universal Synchronous/Asynchronous Receiver/Transmitter (UART/SPI/SmartCard (ISO 7816)/IrDA) * Low Energy UART (LEUARTTM) * I2C interface with SMBus support and address recognition in EM3 Stop * Wide Operating Range * 2.3 V to 3.6 V single power supply * Integrated DC-DC, down to 1.8 V output with up to 200 mA load current for system * Standard (-40 C to 85 C) and Extended (-40 C to 125 C) temperature grades available * QFN32 5x5 mm Package Rev. 1.0 | 1 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Ordering Information 2. Ordering Information Ordering Code Protocol Stack Frequency Band @ Max TX Power Flash (kB) Serial Flash (kB) RAM (kB) Temp Range EFR32MG1P732F256GM32-C0 * Bluetooth Smart * ZigBee * Thread * ZigBee RC * Proprietary 2.4 GHz @ 19.5 dBm 256 512 32 -40 to +85 EFR32MG1P732F256IM32-C0 * Bluetooth Smart * ZigBee * Thread * ZigBee RC * Proprietary 2.4 GHz @ 19.5 dBm 256 512 32 -40 to +125 EFR32MG1P632F256GM32-C0 * Bluetooth Smart * ZigBee * Thread * ZigBee RC * Proprietary 2.4 GHz @ 16.5 dBm 256 512 32 -40 to +85 EFR32MG1P632F256IM32-C0 * Bluetooth Smart * ZigBee * Thread * ZigBee RC * Proprietary 2.4 GHz @ 16.5 dBm 256 512 32 -40 to +125 EFR32MG1B732F256GM32-C0 * ZigBee * Thread * ZigBee RC 2.4 GHz @ 19.5 dBm 256 512 32 -40 to +85 EFR32MG1B732F256IM32-C0 * ZigBee * Thread * ZigBee RC 2.4 GHz @ 19.5 dBm 256 512 32 -40 to +125 EFR32MG1B632F256GM32-C0 * ZigBee * Thread * ZigBee RC 2.4 GHz @ 16.5 dBm 256 512 32 -40 to +85 EFR32MG1B632F256IM32-C0 * ZigBee * Thread * ZigBee RC 2.4 GHz @ 16.5 dBm 256 512 32 -40 to +125 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 2 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Ordering Information EFR32 X G 1 P 132 F 256 G M 32 - C0 R Tape and Reel (Optional) Revision Pin Count Package - M (QFN), J (CSP) Temperature Grade - G (-40 to +85 C), -I (-40 to +125 C) Flash Memory Size in kB Memory Type (Flash) Feature Set Code - r2r1r0 r2: Reserved r1: RF Type - 3 (TRX), 2 (RX), 1 (TX) r0: Frequency Band - 1 (Sub-GHz), 2 (2.4 GHz), 3 (Dual-Band) Performance Grade - P (Performance), B (Basic), V (Value) Generation Gecko Family - M (Mighty), B (Blue), F (Flex) Wireless Gecko 32-bit Figure 2.1. OPN Decoder silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 3 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3. System Overview 3.1 Introduction The EFR32 product family combines an energy-friendly MCU with a highly integrated radio transceiver. This section gives a short introduction to the full radio and MCU system. The detailed functional description can be found in the EFR32 Reference Manual. A block diagram of the EFR32MG1 family is shown in Figure 3.1 Detailed EFR32MG1 Block Diagram on page 4. The diagram shows a superset of features available on the family, which vary by OPN. For more information about specific device features, consult Ordering Information. Radio Transciever RF Frontend I IFADC PGA FRC Digital Peripherals LETIMER LNA BALUN PA Frequency Synthesizer Q AGC MOD CRYOTIMER RAC 2G4RF_ION IOVDD TIMER CRC 2G4RF_IOP PCNT RTC / RTCC Port Mapper USART ARM Cortex-M4 Core Energy Management PAVDD RFVDD IOVDD Voltage Monitor DVDD VREGVDD VREGSW CRYPTO Up to 32 kB RAM CRC Floating Point Unit bypass DC-DC Converter RESETn A A H P B B Co-Packaged Resources Voltage Regulator Serial Wire Debug / Programming Watchdog Timer Brown Out / Power-On Reset Analog Peripherals Internal Reference VDD ULFRCO AUXHFRCO 12-bit ADC HFXTAL_P LFXTAL_P / N LFXO HFXO Port C Drivers PCn Port D Drivers PDn Port F Drivers PFn VDD Temp Sensor LFRCO HFRCO HFXTAL_N PBn IDAC VREF Clock Management Reset Management Unit Port B Drivers 512 kB Serial Flash Memory DMA Controller DECOUPLE VSS VREGVSS RFVSS PAVSS I2C Up to 256 kB ISP Flash Program Memory Memory Protection Unit PAn LEUART Input MUX AVDD Port A Drivers APORT RFSENSE BUFC Port I/O Configuration DEMOD + Analog Comparator Figure 3.1. Detailed EFR32MG1 Block Diagram 3.2 Radio The Mighty Gecko family features a highly configurable radio transceiver supporting a wide range of wireless protocols. 3.2.1 Antenna Interface The 2.4 GHz antenna interface consists of two pins (2G4RF_IOP and 2G4RF_ION) that interface directly to the on-chip BALUN. The 2G4RF_ION pin should be grounded externally. The external components and power supply connections for the antenna interface typical applications are shown in the RF Matching Networks section. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 4 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.2.2 Fractional-N Frequency Synthesizer The EFR32MG1 contains a high performance, low phase noise, fully integrated fractional-N frequency synthesizer. The synthesizer is used in receive mode to generate the LO frequency used by the down-conversion mixer. It is also used in transmit mode to directly generate the modulated RF carrier. The fractional-N architecture provides excellent phase noise performance combined with frequency resolution better than 100 Hz, with low energy consumption. The synthesizer has fast frequency settling which allows very short receiver and transmitter wake up times to optimize system energy consumption. 3.2.3 Receiver Architecture The EFR32MG1 uses a low-IF receiver architecture, consisting of a Low-Noise Amplifier (LNA) followed by an I/Q down-conversion mixer, employing a crystal reference. The I/Q signals are further filtered and amplified before being sampled by the IF analog-to-digital converter (IFADC). The IF frequency is configurable from 150 kHz to 1371 kHz. The IF can further be configured for high-side or low-side injection, providing flexibility with respect to known interferers at the image frequency. The Automatic Gain Control (AGC) module adjusts the receiver gain to optimize performance and avoid saturation for excellent selectivity and blocking performance. Devices are production-calibrated to improve image rejection performance. Demodulation is performed in the digital domain. The demodulator performs configurable decimation and channel filtering to allow receive bandwidths ranging from 0.1 to 2530 kHz. High carrier frequency and baud rate offsets are tolerated by active estimation and compensation. Advanced features supporting high quality communication under adverse conditions include forward error correction by block and convolutional coding as well as Direct Sequence Spread Spectrum (DSSS). A Received Signal Strength Indicator (RSSI) is available for signal quality metrics, for level-based proximity detection, and for RF channel access by Collision Avoidance (CA) or Listen Before Talk (LBT) algorithms. An RSSI capture value is associated with each received frame and the dynamic RSSI measurement can be monitored throughout reception. The EFR32MG1 features integrated support for antenna diversity to improve link budget, using complementary control outputs to an external switch. Internal configurable hardware controls automatic switching between antennae during RF receive detection operations. 3.2.4 Transmitter Architecture The EFR32MG1 uses a direct-conversion transmitter architecture. For constant envelope modulation formats, the modulator controls phase and frequency modulation in the frequency synthesizer. Transmit symbols or chips are optionally shaped by a digital shaping filter. The shaping filter is fully configurable, including the BT product, and can be used to implement Gaussian or Raised Cosine shaping. Carrier Sense Multiple Access - Collision Avoidance (CSMA-CA) or Listen Before Talk (LBT) algorithms can be automatically timed by the EFR32MG1. These algorithms are typically defined by regulatory standards to improve inter-operability in a given bandwidth between devices that otherwise lack synchronized RF channel access. 3.2.5 Wake on Radio The Wake on Radio feature allows flexible, autonomous RF sensing, qualification, and demodulation without required MCU activity, using a subsystem of the EFR32MG1 including the Radio Controller (RAC), Peripheral Reflex System (PRS), and Low Energy peripherals. 3.2.6 RFSENSE The RFSENSE module generates a system wakeup interrupt upon detection of wideband RF energy at the antenna interface, providing true RF wakeup capabilities from low energy modes including EM2, EM3 and EM4. RFSENSE triggers on a relatively strong RF signal and is available in the lowest energy modes, allowing exceptionally low energy consumption. RFSENSE does not demodulate or otherwise qualify the received signal, but software may respond to the wakeup event by enabling normal RF reception. Various strategies for optimizing power consumption and system response time in presence of false alarms may be employed using available timer peripherals. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 5 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.2.7 Flexible Frame Handling EFR32MG1 has an extensive and flexible frame handling support for easy implementation of even complex communication protocols. The Frame Controller (FRC) supports all low level and timing critical tasks together with the Radio Controller and Modulator/ Demodulator: * Highly adjustable preamble length * Up to 2 simultaneous synchronization words, each up to 32 bits and providing separate interrupts * Frame disassembly and address matching (filtering) to accept or reject frames * Automatic ACK frame assembly and transmission * Fully flexible CRC generation and verification: * Multiple CRC values can be embedded in a single frame * 8, 16, 24 or 32-bit CRC value * Configurable CRC bit and byte ordering * Selectable bit-ordering (least significant or most significant bit first) * Optional data whitening * Optional Forward Error Correction (FEC), including convolutional encoding / decoding and block encoding / decoding * Half rate convolutional encoder and decoder with constraint lengths from 2 to 7 and optional puncturing * Optional symbol interleaving, typically used in combination with FEC * Symbol coding, such as Manchester or DSSS, or biphase space encoding using FEC hardware * UART encoding over air, with start and stop bit insertion / removal * Test mode support, such as modulated or unmodulated carrier output * Received frame timestamping 3.2.8 Packet and State Trace The EFR32MG1 Frame Controller has a packet and state trace unit that provides valuable information during the development phase. It features: * Non-intrusive trace of transmit data, receive data and state information * Data observability on a single-pin UART data output, or on a two-pin SPI data output * Configurable data output bitrate / baudrate * Multiplexed transmitted data, received data and state / meta information in a single serial data stream 3.2.9 Data Buffering The EFR32MG1 features an advanced Radio Buffer Controller (BUFC) capable of handling up to 4 buffers of adjustable size from 64 bytes to 4096 bytes. Each buffer can be used for RX, TX or both. The buffer data is located in RAM, enabling zero-copy operations. 3.2.10 Radio Controller (RAC) The Radio Controller controls the top level state of the radio subsystem in the EFR32MG1. It performs the following tasks: * Precisely-timed control of enabling and disabling of the receiver and transmitter circuitry * Run-time calibration of receiver, transmitter and frequency synthesizer * Detailed frame transmission timing, including optional LBT or CSMA-CA 3.2.11 Random Number Generator The Frame Controller (FRC) implements a random number generator that uses entropy gathered from noise in the RF receive chain. The data is suitable for use in cryptographic applications. Output from the random number generator can be used either directly or as a seed or entropy source for software-based random number generator algorithms such as Fortuna. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 6 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.3 Power The EFR32MG1 has an Energy Management Unit (EMU) and efficient integrated regulators to generate internal supply voltages. Only a single external supply voltage is required, from which all internal voltages are created. An optional integrated DC-DC buck regulator can be utilized to further reduce the current consumption. The DC-DC regulator requires one external inductor and one external capacitor. Running from a sufficiently high supply, the device can use the DC-DC to regulate voltage not only for itself, but also for other PCB components, supplying up to a total of 200 mA. 3.3.1 Energy Management Unit (EMU) The Energy Management Unit manages transitions of energy modes in the device. Each energy mode defines which peripherals and features are available and the amount of current the device consumes. The EMU can also be used to turn off the power to unused RAM blocks, and it contains control registers for the dc-dc regulator and the Voltage Monitor (VMON). The VMON is used to monitor multiple supply voltages. It has multiple channels which can be programmed individually by the user to determine if a sensed supply has fallen below a chosen threshold. 3.3.2 DC-DC Converter The DC-DC buck converter covers a wide range of load currents and provides up to 90% efficiency in energy modes EM0, EM1, EM2 and EM3, and can supply up to 200 mA to the device and surrounding PCB components. Patented RF noise mitigation allows operation of the DC-DC converter without degrading sensitivity of radio components. Protection features include programmable current limiting, short-circuit protection, and dead-time protection. The DC-DC converter may also enter bypass mode when the input voltage is too low for efficient operation. In bypass mode, the DC-DC input supply is internally connected directly to its output through a low resistance switch. Bypass mode also supports in-rush current limiting to prevent input supply voltage droops due to excessive output current transients. 3.4 General Purpose Input/Output (GPIO) EFR32MG1 has up to 16 General Purpose Input/Output pins. Each GPIO pin can be individually configured as either an output or input. More advanced configurations including open-drain, open-source, and glitch-filtering can be configured for each individual GPIO pin. The GPIO pins can be overridden by peripheral connections, like SPI communication. Each peripheral connection can be routed to several GPIO pins on the device. The input value of a GPIO pin can be routed through the Peripheral Reflex System to other peripherals. The GPIO subsystem supports asynchronous external pin interrupts. 3.5 Clocking 3.5.1 Clock Management Unit (CMU) The Clock Management Unit controls oscillators and clocks in the EFR32MG1. Individual enabling and disabling of clocks to all peripheral modules is performed by the CMU. The CMU also controls enabling and configuration of the oscillators. A high degree of flexibility allows software to optimize energy consumption in any specific application by minimizing power dissipation in unused peripherals and oscillators. 3.5.2 Internal and External Oscillators The EFR32MG1 supports two crystal oscillators and fully integrates four RC oscillators, listed below. * A high frequency crystal oscillator (HFXO) with integrated load capacitors, tunable in small steps, provides a precise timing reference for the MCU. Crystal frequencies in the range from 38 to 40 MHz are supported. An external clock source such as a TCXO can also be applied to the HFXO input for improved accuracy over temperature. * A 32.768 kHz crystal oscillator (LFXO) provides an accurate timing reference for low energy modes. * An integrated high frequency RC oscillator (HFRCO) is available for the MCU system, when crystal accuracy is not required. The HFRCO employs fast startup at minimal energy consumption combined with a wide frequency range. * An integrated auxilliary high frequency RC oscillator (AUXHFRCO) is available for timing the general-purpose ADC and the Serial Wire debug port with a wide frequency range. * An integrated low frequency 32.768 kHz RC oscillator (LFRCO) can be used as a timing reference in low energy modes, when crystal accuracy is not required. * An integrated ultra-low frequency 1 kHz RC oscillator (ULFRCO) is available to provide a timing reference at the lowest energy consumption in low energy modes. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 7 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.6 Counters/Timers and PWM 3.6.1 Timer/Counter (TIMER) TIMER peripherals keep track of timing, count events, generate PWM outputs and trigger timed actions in other peripherals through the PRS system. The core of each TIMER is a 16-bit counter with up to 4 compare/capture channels. Each channel is configurable in one of three modes. In capture mode, the counter state is stored in a buffer at a selected input event. In compare mode, the channel output reflects the comparison of the counter to a programmed threshold value. In PWM mode, the TIMER supports generation of pulse-width modulation (PWM) outputs of arbitrary waveforms defined by the sequence of values written to the compare registers, with optional dead-time insertion available in timer unit TIMER_0 only. 3.6.2 Real Time Counter and Calendar (RTCC) The Real Time Counter and Calendar (RTCC) is a 32-bit counter providing timekeeping in all energy modes. The RTCC includes a Binary Coded Decimal (BCD) calendar mode for easy time and date keeping. The RTCC can be clocked by any of the on-board oscillators with the exception of the AUXHFRCO, and it is capable of providing system wake-up at user defined instances. When receiving frames, the RTCC value can be used for timestamping. The RTCC includes 128 bytes of general purpose data retention, allowing easy and convenient data storage in all energy modes. 3.6.3 Low Energy Timer (LETIMER) The unique LETIMER is a 16-bit timer that is available in energy mode EM2 Deep Sleep in addition to EM1 Sleep and EM0 Active. This allows it to be used for timing and output generation when most of the device is powered down, allowing simple tasks to be performed while the power consumption of the system is kept at an absolute minimum. The LETIMER can be used to output a variety of waveforms with minimal software intervention. The LETIMER is connected to the Real Time Counter and Calendar (RTCC), and can be configured to start counting on compare matches from the RTCC. 3.6.4 Ultra Low Power Wake-up Timer (CRYOTIMER) The CRYOTIMER is a 32-bit counter that is capable of running in all energy modes. It can be clocked by either the 32.768 kHz crystal oscillator (LFXO), the 32.768 kHz RC oscillator (LFRCO), or the 1 kHz RC oscillator (ULFRCO). It can provide periodic Wakeup events and PRS signals which can be used to wake up peripherals from any energy mode. The CRYOTIMER provides a wide range of interrupt periods, facilitating flexible ultra-low energy operation. 3.6.5 Pulse Counter (PCNT) The Pulse Counter (PCNT) peripheral can be used for counting pulses on a single input or to decode quadrature encoded inputs. The clock for PCNT is selectable from either an external source on pin PCTNn_S0IN or from an internal timing reference, selectable from among any of the internal oscillators, except the AUXHFRCO. The module may operate in energy mode EM0 Active, EM1 Sleep, EM2 Deep Sleep, and EM3 Stop. 3.6.6 Watchdog Timer (WDOG) The watchdog timer can act both as an independent watchdog or as a watchdog synchronous with the CPU clock. It has windowed monitoring capabilities, and can generate a reset or different interrupts depending on the failure mode of the system. The watchdog can also monitor autonomous systems driven by PRS. 3.7 Communications and Other Digital Peripherals 3.7.1 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) The Universal Synchronous/Asynchronous Receiver/Transmitter is a flexible serial I/O module. It supports full duplex asynchronous UART communication with hardware flow control as well as RS-485, SPI, MicroWire and 3-wire. It can also interface with devices supporting: * ISO7816 SmartCards * IrDA 3.7.2 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) The unique LEUARTTM provides two-way UART communication on a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud. The LEUART includes all necessary hardware to make asynchronous serial communication possible with a minimum of software intervention and energy consumption. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 8 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.7.3 Inter-Integrated Circuit Interface (I2C) The I2C module provides an interface between the MCU and a serial I2C bus. It is capable of acting as both a master and a slave and supports multi-master buses. Standard-mode, fast-mode and fast-mode plus speeds are supported, allowing transmission rates from 10 kbit/s up to 1 Mbit/s. Slave arbitration and timeouts are also available, allowing implementation of an SMBus-compliant system. The interface provided to software by the I2C module allows precise timing control of the transmission process and highly automated transfers. Automatic recognition of slave addresses is provided in active and low energy modes. 3.7.4 Peripheral Reflex System (PRS) The Peripheral Reflex System provides a communication network between different peripheral modules without software involvement. Peripheral modules producing Reflex signals are called producers. The PRS routes Reflex signals from producers to consumer peripherals which in turn perform actions in response. Edge triggers and other functionality can be applied by the PRS. The PRS allows peripheral to act autonomously without waking the MCU core, saving power. 3.8 Security Features 3.8.1 GPCRC (General Purpose Cyclic Redundancy Check) The GPCRC module implements a Cyclic Redundancy Check (CRC) function. It supports both 32-bit and 16-bit polynomials. The supported 32-bit polynomial is 0x04C11DB7 (IEEE 802.3), while the 16-bit polynomial can be programmed to any value, depending on the needs of the application. 3.8.2 Crypto Accelerator (CRYPTO) The Crypto Accelerator is a fast and energy-efficient autonomous hardware encryption and decryption accelerator. EFR32 devices support various levels of hardware-accelerated encryption, depending on the part number. AES-only devices support AES encryption and decryption with 128- or 256-bit keys. Full crypto support adds ECC over both GF(P) and GF(2m), SHA-1 and SHA-2 (SHA-224 and SHA-256). Supported block cipher modes of operation for AES include: ECB, CTR, CBC, PCBC, CFB, OFB, GCM, CBC-MAC, GMAC and CCM. Supported ECC NIST recommended curves include P-192, P-224, P-256, K-163, K-233, B-163 and B-233. The CRYPTO is tightly linked to the Radio Buffer Controller (BUFC) enabling fast and efficient autonomous cipher operations on data buffer content. It allows fast processing of GCM (AES), ECC and SHA with little CPU intervention. CRYPTO also provides trigger signals for DMA read and write operations. 3.9 Analog 3.9.1 Analog Port (APORT) The Analog Port (APORT) is an analog interconnect matrix allowing access to analog modules ADC, ACMP, and IDAC on a flexible selection of pins. Each APORT bus consists of analog switches connected to a common wire. Since many clients can operate differentially, buses are grouped by X/Y pairs. 3.9.2 Analog Comparator (ACMP) The Analog Comparator is used to compare the voltage of two analog inputs, with a digital output indicating which input voltage is higher. Inputs are selected from among internal references and external pins. The tradeoff between response time and current consumption is configurable by software. Two 6-bit reference dividers allow for a wide range of internally-programmable reference sources. The ACMP can also be used to monitor the supply voltage. An interrupt can be generated when the supply falls below or rises above the programmable threshold. 3.9.3 Analog to Digital Converter (ADC) The ADC is a Successive Approximation Register (SAR) architecture, with a resolution of up to 12 bits at up to 1 MSamples/s. The output sample resolution is configurable and additional resolution is possible using integrated hardware for averaging over multiple samples. The ADC includes integrated voltage references and an integrated temperature sensor. Inputs are selectable from a wide range of sources, including pins configurable as either single-ended or differential. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 9 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.9.4 Digital to Analog Current Converter (IDAC) The Digital to Analog Current Converter can source or sink a configurable constant current. This current can be driven on an output pin or routed to the selected ADC input pin for capacitive sensing. The current is programmable between 0.05 A and 64 A with several ranges with various step sizes. 3.10 Reset Management Unit (RMU) The RMU is responsible for handling reset of the EFR32MG1. A wide range of reset sources are available, including several power supply monitors, pin reset, software controlled reset, core lockup reset and watchdog reset. 3.11 Core and Memory 3.11.1 Processor Core The ARM Cortex-M processor includes a 32-bit RISC processor integrating the following features and tasks in the system: * ARM Cortex-M4 RISC processor achieving 1.25 Dhrystone MIPS/MHz * Memory Protection Unit (MPU) supporting up to 8 memory segments * Up to 256 kB flash program memory * Up to 32 kB RAM data memory * Configuration and event handling of all modules * 2-pin Serial-Wire debug interface 3.11.2 Serial Flash 512 kB of high-speed, low-power serial flash is included in the system, accessible via a dedicated serial interface. The serial flash is internal to the package, requiring no additional area on the PCB. Software libraries enable easy API-level access to this memory space. 3.11.3 Memory System Controller (MSC) The Memory System Controller (MSC) is the program memory unit of the microcontroller. The flash memory is readable and writable from both the Cortex-M and DMA. The flash memory is divided into two blocks; the main block and the information block. Program code is normally written to the main block, whereas the information block is available for special user data and flash lock bits. There is also a read-only page in the information block containing system and device calibration data. Read and write operations are supported in energy modes EM0 Active and EM1 Sleep. 3.11.4 Linked Direct Memory Access Controller (LDMA) The Linked Direct Memory Access (LDMA) controller features 8 channels capable of performing memory operations independently of software. This reduces both energy consumption and software workload. The LDMA allows operations to be linked together and staged, enabling sophisticated operations to be implemented. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 10 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview 3.12 Memory Map The EFR32MG1 memory map is shown in the figures below. RAM and flash sizes are for the largest memory configuration. Figure 3.2. EFR32MG1 Memory Map -- Core Peripherals and Code Space silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 11 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet System Overview Figure 3.3. EFR32MG1 Memory Map -- Peripherals 3.13 Configuration Summary The features of the EFR32MG1 are a subset of the feature set described in the device reference manual. The table below describes device specific implementation of the features. Remaining modules support full configuration. Table 3.1. Configuration Summary Module Configuration Pin Connections USART0 IrDA SmartCard US0_TX, US0_RX, US0_CLK, US0_CS TIMER0 with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 silabs.com | Smart. Connected. Energy-friendly. TIM1_CC[3:0] Rev. 1.0 | 12 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4. Electrical Specifications 4.1 Electrical Characteristics All electrical parameters in all tables are specified under the following conditions, unless stated otherwise: * Typical values are based on TAMB=25 C and VDD= 3.3 V, by production test and/or technology characterization. * Radio performance numbers are measured in conducted mode, based on Silicon Laboratories reference designs using output power-specific external RF impedance-matching networks for interfacing to a 50 antenna. * Minimum and maximum values represent the worst conditions across supply voltage, process variation, and operating temperature, unless stated otherwise. Refer to Table 4.2 General Operating Conditions on page 15 for more details about operational supply and temperature limits. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 13 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.1 Absolute Maximum Ratings Stresses above those listed below may cause permanent damage to the device. This is a stress rating only and functional operation of the devices at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. For more information on the available quality and reliability data, see the Quality and Reliability Monitor Report at http://www.silabs.com/support/quality/pages/default.aspx. Table 4.1. Absolute Maximum Ratings Parameter Symbol Storage temperature range TSTG Min Typ Max Unit -50 -- 150 C External main supply voltage VDDMAX 0 -- 3.6 V External main supply voltage VDDRAMPMAX ramp rate -- -- 1 V / s -0.3 -- Min of 5.25 and IOVDD +2 V -0.3 -- IOVDD+0.3 V -0.3 -- 1.4 V Voltage on any 5V tolerant GPIO pin1 VDIGPIN Voltage on non-5V tolerant GPIO pins Test Condition Voltage on HFXO pins VHFXOPIN Input RF level on pins 2G4RF_IOP and 2G4RF_ION PRFMAX2G4 -- -- 10 dBm Voltage differential between RF pins (2G4RF_IOP 2G4RF_ION) VMAXDIFF2G4 -50 -- 50 mV Absolute Voltage on RF pins VMAX2G4 2G4RF_IOP and 2G4RF_ION -0.3 -- 3.3 V Total current into VDD power IVDDMAX lines (source) -- -- 200 mA Total current into VSS ground lines (sink) IVSSMAX -- -- 200 mA Current per I/O pin (sink) IIOMAX -- -- 50 mA -- -- 50 mA -- -- 200 mA -- -- 200 mA Current per I/O pin (source) Current for all I/O pins (sink) IIOALLMAX Current for all I/O pins (source) Voltage difference between AVDD and VREGVDD VDD -- -- 0.3 V Junction Temperature for -G grade devices TJ -40 -- 105 C -40 -- 125 C Junction Temperature for -I grade devices Note: 1. When a GPIO pin is routed to the analog module through the APORT, the maximum voltage = IOVDD. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 14 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.2 Operating Conditions When assigning supply sources, the following requirements must be observed: * VREGVDD must be the highest voltage in the system * VREGVDD = AVDD * DVDD AVDD * IOVDD AVDD * RFVDD AVDD * PAVDD AVDD 4.1.2.1 General Operating Conditions Table 4.2. General Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit -G temperature grade, Ambient Temperature -40 25 85 C -I temperature grade, Junction Temperature -40 25 125 C 2.3 3.3 3.6 V DCDC in regulation 2.4 3.3 3.6 V DCDC in bypass 50mA load 2.3 3.3 3.6 V DCDC not in use. DVDD externally shorted to VREGVDD 2.3 3.3 3.6 V DCDC in bypass, Tamb 85 C -- -- 200 mA DCDC in bypass, Tamb > 85 C -- -- 100 mA 1.62 -- VVREGVDD V DVDD Operating supply volt- VDVDD age 1.62 -- VVREGVDD V PAVDD Operating supply voltage VPAVDD 1.62 -- VVREGVDD V IOVDD Operating supply voltage VIOVDD 2.3 -- VVREGVDD V -- -- 0.1 V 0 wait-states (MODE = WS0) 3 -- -- 26 MHz 1 wait-states (MODE = WS1) 3 -- 38.4 40 MHz Operating temperature range TOP AVDD Supply voltage1 VAVDD VREGVDD Operating supply VVREGVDD voltage1 2 VREGVDD Current RFVDD Operating supply voltage IVREGVDD VRFVDD Difference between AVDD dVDD and VREGVDD, ABS(AVDDVREGVDD) HFCLK frequency fCORE Note: 1. VREGVDD must be tied to AVDD. Both VREGVDD and AVDD minimum voltages must be satisfied for the part to operate. 2. The minimum voltage required in bypass mode is calculated using RBYP from the DCDC specification table. Requirements for other loads can be calculated as VDVDD_min+ILOAD * RBYP_max 3. In MSC_READCTRL register silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 15 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.3 Thermal Characteristics Table 4.3. Thermal Characteristics Parameter Symbol Test Condition Thermal Resistance THETAJA silabs.com | Smart. Connected. Energy-friendly. Min Typ Max Unit QFN32 Package, 2-Layer PCB, Air velocity = 0 m/s -- 85.2 -- C/W QFN32 Package, 2-Layer PCB, Air velocity = 1 m/s -- 67.1 -- C/W QFN32 Package, 2-Layer PCB, Air velocity = 2 m/s -- 58.3 -- C/W QFN32 Package, 4-Layer PCB, Air velocity = 0 m/s -- 36.9 -- C/W QFN32 Package, 4-Layer PCB, Air velocity = 1 m/s -- 32.4 -- C/W QFN32 Package, 4-Layer PCB, Air velocity = 2 m/s -- 31 -- C/W Rev. 1.0 | 16 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.4 DC-DC Converter Test conditions: LDCDC=4.7 H (Murata LQH3NPN4R7MM0L), CDCDC=1.0 F (Murata GRM188R71A105KA61D), VDCDC_I=3.3 V, VDCDC_O=1.8 V, IDCDC_LOAD=50 mA, Heavy Drive configuration, FDCDC_LN=7 MHz, unless otherwise indicated. Table 4.4. DC-DC Converter Parameter Symbol Test Condition Min Typ Max Unit Input voltage range VDCDC_I Bypass mode, IDCDC_LOAD = 50 mA 2.3 -- VVREGVDD_ V Low noise (LN) mode, 1.8 V output, IDCDC_LOAD = 100 mA, or Low power (LP) mode, 1.8 V output, IDCDC_LOAD = 10 mA 2.4 Low noise (LN) mode, 1.8 V output, IDCDC_LOAD = 200 mA 2.6 Output voltage programmable range1 VDCDC_O Regulation DC Accuracy ACCDC Regulation Window2 WINREG MAX -- VVREGVDD_ V MAX -- VVREGVDD_ V MAX 1.8 -- VVREGVDD V Low noise (LN) mode, 1.8 V target output 1.7 -- 1.9 V Low power (LP) mode, LPCMPBIAS3 = 0, 1.8 V target output, IDCDC_LOAD 75 A 1.63 -- 2.2 V Low power (LP) mode, LPCMPBIAS3 = 3, 1.8 V target output, IDCDC_LOAD 10 mA 1.63 -- 2.1 V Steady-state output ripple VR Radio disabled. -- 3 -- mVpp Output voltage under/overshoot VOV CCM Mode (LNFORCECCM3 = 1), Load changes between 0 mA and 100 mA -- -- 150 mV DCM Mode (LNFORCECCM3 = 0), Load changes between 0 mA and 10 mA -- -- 150 mV Overshoot during LP to LN CCM/DCM mode transitions compared to DC level in LN mode -- 200 -- mV Undershoot during BYP/LP to LN CCM (LNFORCECCM3 = 1) mode transitions compared to DC level in LN mode -- 50 -- mV Undershoot during BYP/LP to LN DCM (LNFORCECCM3 = 0) mode transitions compared to DC level in LN mode -- 125 -- mV DC line regulation VREG Input changes between VVREGVDD_MAX and 2.4 V -- 0.1 -- % DC load regulation IREG Load changes between 0 mA and 100 mA in CCM mode -- 0.1 -- % silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 17 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Max load current ILOAD_MAX Low noise (LN) mode, Heavy Drive4, Tamb 85 C -- -- 200 mA Low noise (LN) mode, Heavy Drive4, Tamb > 85 C -- -- 100 mA Low noise (LN) mode, Medium Drive4 -- -- 100 mA Low noise (LN) mode, Light Drive4 -- -- 50 mA Low power (LP) mode, LPCMPBIAS3 = 0 -- -- 75 A Low power (LP) mode, LPCMPBIAS3 = 3 -- -- 10 mA CDCDC 25% tolerance 1 1 1 F DCDC nominal output induc- LDCDC tor 20% tolerance 4.7 4.7 4.7 H -- 1.2 2.5 DCDC nominal output capacitor Resistance in Bypass mode RBYP Note: 1. Due to internal dropout, the DC-DC output will never be able to reach its input voltage, VVREGVDD 2. LP mode controller is a hysteretic controller that maintains the output voltage within the specified limits 3. In EMU_DCDCMISCCTRL register 4. Drive levels are defined by configuration of the PFETCNT and NFETCNT registers. Light Drive: PFETCNT=NFETCNT=3; Medium Drive: PFETCNT=NFETCNT=7; Heavy Drive: PFETCNT=NFETCNT=15. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 18 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.5 Current Consumption 4.1.5.1 Current Consumption 3.3 V without DC-DC Converter Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = DVDD = RFVDD = PAVDD = 3.3 V. TOP = 25 C. EMU_PWRCFG_PWRCG=NODCDC. EMU_DCDCCTRL_DCDCMODE=BYPASS. Minimum and maximum values in this table represent the worst conditions across supply voltage and process variation at TOP = 25 C. See Figure 5.1 EFR32MG1 Typical Application Circuit: Direct Supply Configuration without DC-DC converter on page 64. Table 4.5. Current Consumption 3.3V without DC/DC Parameter Symbol Min Typ Max Unit 38.4 MHz crystal, CPU running while loop from flash1 -- 130 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 88 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 100 105 A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 112 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 102 106 A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 222 350 A/MHz 38.4 MHz crystal1 -- 65 -- A/MHz 38 MHz HFRCO -- 35 38 A/MHz 26 MHz HFRCO -- 37 41 A/MHz 1 MHz HFRCO -- 157 275 A/MHz Full RAM retention and RTCC running from LFXO, serial flash in deep power down -- 6.3 -- A 4 kB RAM retention and RTCC running from LFRCO, serial flash in deep power down -- 6 9.2 A Current consumption in EM3 IEM3 Stop mode Full RAM retention and CRYOTIMER running from ULFRCO, serial flash in deep power down -- 5.8 9.2 A Current consumption in EM4H Hibernate mode 128 byte RAM retention, RTCC running from LFXO -- 4.1 -- A 128 byte RAM retention, CRYOTIMER running from ULFRCO -- 3.65 -- A 128 byte RAM retention, no RTCC -- 3.65 4.7 A no RAM retention, no RTCC -- 3.04 3.6 A Current consumption in EM0 IACTIVE Active mode with all peripherals disabled Current consumption in EM1 IEM1 Sleep mode with all peripherals disabled Current consumption in EM2 IEM2 Deep Sleep mode. Current consumption in EM4S Shutoff mode IEM4 IEM4S Test Condition Note: 1. CMU_HFXOCTRL_LOWPOWER=0 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 19 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.5.2 Current Consumption 3.3 V using DC-DC Converter Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD = 1.8 V DC-DC output. TOP = 25 C. Minimum and maximum values in this table represent the worst conditions across supply voltage and process variation at TOP = 25 C. See Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64. Table 4.6. Current Consumption 3.3V with DC-DC Parameter Symbol Current consumption in EM0 IACTIVE Active mode with all peripherals disabled, DCDC in Low Noise DCM mode1. Current consumption in EM0 Active mode with all peripherals disabled, DCDC in Low Noise CCM mode3. Current consumption in EM1 IEM1 Sleep mode with all peripherals disabled, DCDC in Low Noise DCM mode1. Test Condition Min Typ Max Unit 38.4 MHz crystal, CPU running while loop from flash2 -- 88 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 63 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 71 -- A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 78 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 76 -- A/MHz 38.4 MHz crystal, CPU running while loop from flash2 -- 98 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 75 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 81 -- A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 88 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 94 -- A/MHz 38.4 MHz crystal2 -- 49 -- A/MHz 38 MHz HFRCO -- 32 -- A/MHz 26 MHz HFRCO -- 38 -- A/MHz Current consumption in EM1 Sleep mode with all peripherals disabled, DCDC in Low Noise CCM mode3. 38.4 MHz crystal2 -- 61 -- A/MHz 38 MHz HFRCO -- 45 -- A/MHz 26 MHz HFRCO -- 58 -- A/MHz Current consumption in EM2 IEM2 Deep Sleep mode. DCDC in Low Power mode4. Full RAM retention and RTCC running from LFXO, serial flash in deep power down -- 5.5 -- A 4 kB RAM retention and RTCC running from LFRCO, serial flash in deep power down -- 5.2 -- A Full RAM retention and CRYOTIMER running from ULFRCO, serial flash in deep power down -- 5.1 -- A Current consumption in EM3 IEM3 Stop mode silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 20 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Current consumption in EM4H Hibernate mode IEM4 Current consumption in EM4S Shutoff mode IEM4S Min Typ Max Unit 128 byte RAM retention, RTCC running from LFXO -- 3.86 -- A 128 byte RAM retention, CRYOTIMER running from ULFRCO -- 3.58 -- A 128 byte RAM retention, no RTCC -- 3.58 -- A no RAM retention, no RTCC -- 3.04 -- A Note: 1. DCDC Low Noise DCM Mode = Light Drive (PFETCNT=NFETCNT=3), F=3.0 MHz (RCOBAND=0), ANASW=DVDD 2. CMU_HFXOCTRL_LOWPOWER=0 3. DCDC Low Noise CCM Mode = Light Drive (PFETCNT=NFETCNT=3), F=6.4 MHz (RCOBAND=4), ANASW=DVDD 4. DCDC Low Power Mode = Medium Drive (PFETCNT=NFETCNT=7), LPOSCDIV=1, LPBIAS=3, LPCILIMSEL=1, ANASW=DVDD 4.1.5.3 Current Consumption Using Radio Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. TOP = 25 C. Minimum and maximum values in this table represent the worst conditions across supply voltage and process variation at TOP = 25 C. See Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 or Figure 5.1 EFR32MG1 Typical Application Circuit: Direct Supply Configuration without DC-DC converter on page 64. Table 4.7. Current Consumption Using Radio 3.3 V with DC-DC Parameter Symbol Test Condition Current consumption in receive mode, active packet reception (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled) IRX Current consumption in transmit mode (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled) ITX RFSENSE current consump- IRFSENSE tion silabs.com | Smart. Connected. Energy-friendly. Min Typ Max Unit 1 Mbit/s, 2GFSK, F = 2.4 GHz, Radio clock prescaled by 4 -- 8.7 -- mA 802.15.4 receiving frame, F = 2.4 GHz, Radio clock prescaled by 3 -- 9.8 -- mA F = 2.4 GHz, CW, 0 dBm output power, Radio clock prescaled by 3 -- 8.2 -- mA F = 2.4 GHz, CW, 3 dBm output power -- 16.5 -- mA F = 2.4 GHz, CW, 8 dBm output power -- 23.3 -- mA F = 2.4 GHz, CW, 10.5 dBm output power -- 32.7 -- mA F = 2.4 GHz, CW, 16.5 dBm output power, PAVDD connected directly to external 3.3V supply -- 83.9 -- mA F = 2.4 GHz, CW, 19.5 dBm output power, PAVDD connected directly to external 3.3V supply -- 126.7 -- mA -- 51 -- nA Rev. 1.0 | 21 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.6 Wake up times Table 4.8. Wake up times Parameter Symbol Test Condition Wake up from EM2 Deep Sleep tEM2_WU Wakeup time from EM1 Sleep tEM1_WU Wake up from EM3 Stop tEM3_WU Wake up from EM4H Hibernate1 tEM4H_WU Wake up from EM4S Shutoff1 tEM4S_WU Min Typ Max Unit Code execution from flash -- 10.7 -- s Code execution from RAM -- 3 -- s Executing from flash -- 3 -- AHB Clocks Executing from RAM -- 3 -- AHB Clocks Executing from flash -- 10.7 -- s Executing from RAM -- 3 -- s Executing from flash -- 60 -- s -- 290 -- s Min Typ Max Unit Note: 1. Time from wakeup request until first instruction is executed. Wakeup results in device reset. 4.1.7 Brown Out Detector Table 4.9. Brown Out Detector Parameter Symbol Test Condition DVDDBOD threshold VDVDDBOD DVDD rising -- -- 1.62 V DVDD falling 1.35 -- -- V DVDD BOD hysteresis VDVDDBOD_HYST -- 24 -- mV DVDD response time tDVDDBOD_DELAY Supply drops at 0.1V/s rate -- 2.4 -- s AVDD BOD threshold VAVDDBOD AVDD rising -- -- 1.85 V AVDD falling 1.62 -- -- V AVDD BOD hysteresis VAVDDBOD_HYST -- 21 -- mV AVDD response time tAVDDBOD_DELAY Supply drops at 0.1V/s rate -- 2.4 -- s EM4 BOD threshold VEM4DBOD AVDD rising -- -- 1.7 V AVDD falling 1.45 -- -- V -- 46 -- mV -- 300 -- s EM4 BOD hysteresis VEM4BOD_HYST EM4 response time tEM4BOD_DELAY silabs.com | Smart. Connected. Energy-friendly. Supply drops at 0.1V/s rate Rev. 1.0 | 22 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.8 Frequency Synthesizer Characteristics Table 4.10. Frequency Synthesizer Characteristics Parameter Symbol Test Condition Min Typ Max Unit RF Synthesizer Frequency range FRANGE_2400 2.4 GHz frequency range 2400 -- 2483.5 MHz LO tuning frequency resolution with 38.4 MHz crystal FRES_2400 2400 - 2483.5 MHz -- -- 73 Hz Maximum frequency deviation with 38.4 MHz crystal FMAX_2400 -- -- 1677 kHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 23 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.9 2.4 GHz RF Transceiver Characteristics 4.1.9.1 RF Transmitter General Characteristics for the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TOP = 25 C,VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency=38.4MHz. RF center frequency 2.45 GHz. Test circuit according to Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 and Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65. Table 4.11. RF Transmitter General Characteristics for 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit Maximum TX power1 POUTMAX 19.5 dBm-rated part numbers. PAVDD connected directly to external 3.3V supply2 -- 19.5 -- dBm 16.5 dBm-rated part numbers. PAVDD connected directly to external 3.3V supply -- 16.5 -- dBm -30 -- dBm Minimum active TX Power POUTMIN CW Output power step size POUTSTEP -5 dBm< Output power < 0 dBm -- 1 -- dB 0 dBm < output power < POUTMAX -- 0.5 -- dB 1.85 V < VVREGVDD < 3.3 V, PAVDD connected directly to external supply, for output power > 10.5 dBm. -- 4.5 -- dB 1.85 V < VVREGVDD < 3.3 V using DC-DC converter -- 2.2 -- dB From -40 to +85 C, PAVDD connected to DC-DC output -- 1.5 -- dB From -40 to +125 C, PAVDD connected to DC-DC output -- 2.2 -- dB From -40 to +85 C, PAVDD connected to external supply -- 1.5 -- dB From -40 to +125 C, PAVDD connected to external supply -- 3.4 -- dB Over RF tuning frequency range -- 0.4 -- dB 2400 -- 2483.5 MHz Output power variation vs supply at POUTMAX Output power variation vs temperature at POUTMAX POUTVAR_V POUTVAR_T Output power variation vs RF POUTVAR_F frequency at POUTMAX RF tuning frequency range FRANGE Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of 2. Ordering Information 2. For Bluetooth, the Maximum TX power on Channel 2456 is limited to +15 dBm to comply with In-band Spurious emissions. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 24 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.9.2 RF Receiver General Characteristics for the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TOP = 25 C,VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency=38.4MHz. RF center frequency 2.440 GHz. Test circuit according to Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 and Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65. Table 4.12. RF Receiver General Characteristics for 2.4 GHz Band Parameter Symbol RF tuning frequency range FRANGE Receive mode maximum spurious emission SPURRX Max spurious emissions dur- SPURRX_FCC ing active receive mode, per FCC Part 15.109(a) Level above which RFSENSE will trigger1 RFSENSETRIG Level below which RFSENSE will not trigger1 RFSENSETHRES 1% PER Sensitivity SENS2GFSK 0.1% BER Sensitivity Test Condition Min Typ Max Unit 2400 -- 2483.5 MHz 30 MHz to 1 GHz -- -57 -- dBm 1 GHz to 12 GHz -- -47 -- dBm 216 MHz to 960 MHz, Conducted Measurement -- -55.2 -- dBm Above 960 MHz, Conducted Measurement -- -47.2 -- dBm CW at 2.45 GHz -- -24 -- dBm -- -50 -- dBm 2 Mbps 2GFSK signal2 -- -89.2 -- dBm 250 kbps 2GFSK signal -- -99.1 -- dBm Note: 1. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. 2. Channel at 2420 MHz will have degraded sensitivity. Sensitivity could be as high as -83dBm on this channel. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 25 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.9.3 RF Transmitter Characteristics for Bluetooth Smart in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TOP = 25 C,VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency=38.4MHz. RF center frequency 2.44 GHz. Test circuit according to Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 and Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65. Table 4.13. RF Transmitter Characteristics for Bluetooth Smart in the 2.4GHz Band Parameter Symbol Transmit 6dB bandwidth TXBW Power spectral density limit PSDLIMIT Min Typ Max Unit -- 740 -- kHz Per FCC part 15.247 at 10 dBm -- -6.5 -- dBm/ 3kHz Per FCC part 15.247 at 20 dBm -- -2.6 -- dBm/ 3kHz Per ETSI 300.328 at 10 dBm/1 MHz -- 10 -- dBm Occupied channel bandwidth OCPETSI328 per ETSI EN300.328 99% BW at highest and lowest channels in band -- 1.1 -- MHz In-band spurious emissions at 10 dBm, with allowed exceptions1 At 2 MHz -- -39.8 -- dBm At 3 MHz -- -42.1 -- dBm At 2 MHz -- -- -20 dBm At 3 MHz -- -- -30 dBm 2nd,3rd, 5, 6, 8, 9,10 harmonics; continuous transmission of modulated carrier -- -47 -- dBm Spurious emissions out-ofSPUROOB_FCC band, per FCC part 15.247, excluding harmonics captured in SPURHARM,FCC. Restricted Bands Above 2.483 GHz or below 2.4 GHz; continuous transmission of modulated carrier3 -- -47 -- dBm Spurious emissions out-ofband, per FCC part 15.247, excluding harmonics captured in SPURHARM,FCC. Non Restricted Bands Above 2.483 GHz or below 2.4 GHz; continuous transmission of modulated carrier -- -26 -- dBc [2400-BW to 2400] MHz, [2483.5 to 2483.5+BW] MHz -- -16 -- dBm [2400-2BW to 2400-BW] MHz, [2483.5+BW to 2483.5+2BW] MHz per ETSI 300.328 -- -26 -- dBm 47-74 MHz,87.5-108 MHz, 174-230 MHz, 470-862 MHz -- -60 -- dBm 25-1000 MHz -- -42 -- dBm 1-12 GHz -- -36 -- dBm SPURINB In-band spurious emissions at 20 dBm, with allowed exceptions1 2 Emissions of harmonics outof-band, per FCC part 15.247 Spurious emissions out-ofband; per ETSI 300.328 SPURHRM_FCC SPURETSI328 Spurious emissions per ETSI SPURETSI440 EN300.440 silabs.com | Smart. Connected. Energy-friendly. Test Condition Rev. 1.0 | 26 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. Per Bluetooth Core_4.2, Section 3.2.2, exceptions are allowed in up to three bands of 1 MHz width, centered on a frequency which is an integer multiple of 1 MHz. These exceptions shall have an absolute value of -20 dBm or less. 2. For 2456 MHz, a maximum output power of 15 dBm is used to achieve this value. 3. For 2480 MHz, a maximum duty cycle of 20% is used to achieve this value. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 27 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.9.4 RF Receiver Characteristics for Bluetooth Smart in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: TOP = 25 C,VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency=38.4MHz. RF center frequency 2.440 GHz. Test circuit according to Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 and Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65. Table 4.14. RF Receiver Characteristics for Bluetooth Smart in the 2.4GHz Band Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 0.1% BER SAT Signal is reference signal1. Packet length is 20 bytes. -- 10 -- dBm Sensitivity, 0.1% BER2 SENS Signal is reference signal1. Using DC-DC converter -- -92.5 -- dBm With non-ideal signals as specified in RF-PHY.TS.4.2.2, section 4.6.1 -- -92 -- dBm Signal to co-channel interfer- C/ICC er, 0.1% BER Desired signal 3 dB above reference sensitivity -- 8.3 -- dB N+1 adjacent channel (1 C/I1+ MHz) selectivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at +1 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -3 -- dB N-1 adjacent channel (1 C/I1MHz) selectivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at -1 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -0.5 -- dB Alternate (2 MHz) selectivity, C/I2 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at 2 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -43 -- dB Alternate (3 MHz) selectivity, C/I3 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at 3 MHz offset. Desired frequency 2404 MHz Fc 2480 MHz -- -46.7 -- dB Selectivity to image frequen- C/IIM cy, 0.1% BER. Desired is reference signal at -67 dBm Interferer is reference signal at image frequency with 1 MHz precision -- -38.7 -- dB Selectivity to image frequency +1 MHz, 0.1% BER. Desired is reference signal at -67 dBm Interferer is reference signal at image frequency +1 MHz with 1 MHz precision -- -48.2 -- dB Interferer frequency 30 MHz f 2000 MHz -- -27 -- dBm Interferer frequency 2003 MHz f 2399 MHz -- -32 -- dBm Interferer frequency 2484 MHz f 2997 MHz -- -32 -- dBm Interferer frequency 3 GHz f 12.75 GHz -- -27 -- dBm C/IIM+1 Blocking, 0.1% BER, Desired BLOCKOOB is reference signal at -67 dBm. Interferer is CW in OOB range. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 28 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Min Typ Max Unit -- -25.8 -- dBm Upper limit of input power RSSIMAX range over which RSSI resolution is maintained 4 -- -- dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -- -- -101 dBm -- -- 0.5 dB Intermodulation performance IM RSSI resolution RSSIRES Test Condition Per Core_4.1, Vol 6, Part A, Section 4.4 with n = 3 Over RSSIMIN to RSSIMAX Note: 1. Reference signal is defined 2GFSK at -67 dBm, Modulation index = 0.5, BT = 0.5, Bit rate = 1 Mbps, desired data = PRBS9; interferer data = PRBS15; frequency accuracy better than 1 ppm 2. Receive sensitivity on Bluetooth Smart channel 26 is -86 dBm silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 29 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.9.5 RF Transmitter Characteristics for 802.15.4 O-QPSK DSSS in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: T=25 C,VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency=38.4 MHz. RF center frequency 2.45 GHz. Test circuit according to Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 and Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65. Table 4.15. RF Transmitter Characteristics for 802.15.4 DSSS-OQPSK in the 2.4GHz Band Parameter Symbol Test Condition Min Typ Max Unit Error vector magnitude (offset EVM), per 802.15.4-2011, not including 2415 MHz channel1 EVM Average across frequency. Signal is DSSS-OQPSK reference packet2 -- 5.5 -- % rms Power spectral density limit PSDLIMIT Relative, at carrier 3.5 MHz -- -26 -- dBc Absolute, at carrier 3.5 MHz3 -- -36 -- dBm Per FCC part 15.247 -- -4.2 -- dBm/ 3kHz Output power level which meets 10dBm/MHz ETSI 300.328 specification -- 12 -- dBm Occupied channel bandwidth OCPETSI328 per ETSI EN300.328 99% BW at highest and lowest channels in band -- 2.25 -- MHz Spurious emissions of harSPURHRM_FCC_ monics in restricted bands R per FCC Part 15.205/15.209, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency is 2450 MHz Continuous transmission of modulated carrier -- -45.8 -- dBm -- -26 -- dBc Spurious emissions of harmonics in harmonics in nonrestricted bands per FCC Part 15.247/15.35, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency is 2450 MHz SPURHRM_FCC_ NRR silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 30 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Spurious emissions out-ofband in restricted bands (30-88 MHz), per FCC part 15.205/15.209, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz SPUROOB_FCC_ Above 2.483 GHz or below 2.4 GHz; continuous transmission of modulated carrier4 -- -52 -- dBm Spurious emissions out-ofband in restricted bands (88-216 MHz), per FCC part 15.205/15.209, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz -- -62 -- dBm Spurious emissions out-ofband in restricted bands (216-960 MHz), per FCC part 15.205/15.209, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz -- -57 -- dBm Spurious emissions out-ofband in restricted bands (>960 MHz), per FCC part 15.205/15.209, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz -- -48 -- dBm R Spurious emissions out-ofSPUROOB_FCC_ band in non-restricted bands NR per FCC Part 15.247, Emissions taken at Pout_Max power level of 19.5 dBm, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz Above 2.483 GHz or below 2.4 GHz; continuous transmission of modulated carrier -- -26 -- dBc Spurious emissions out-ofband; per ETSI 300.3285 [2400-BW to 2400], [2483.5 to 2483.5+BW]; -- -16 -- dBm [2400-2BW to 2400-BW], [2483.5+BW to 2483.5+2BW]; per ETSI 300.328 -- -26 -- dBm 47-74 MHz,87.5-108 MHz, 174-230 MHz, 470-862 MHz -- -60 -- dBm 25-1000 MHz, excluding above frequencies -- -42 -- dBm 1G-14G -- -36 -- dBm SPURETSI328 Spurious emissions per ETSI SPURETSI440 EN300.4405 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 31 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. Typical EVM for the 2415 MHz channel is 7.9% 2. Reference packet is defined as 20 octet PSDU, modulated according to 802.15.4-2011 DSSS-OQPSK in the 2.4GHz band, with pseudo-random packet data content 3. For 2415 MHz, a maximum duty cycle of 50% is used to achieve this value. 4. For 2480 MHz, a maximum duty cycle of 20% is used to achieve this value. 5. Specified at maximum power output level of 10 dBm silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 32 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.9.6 RF Receiver Characteristics for 802.15.4 O-QPSK DSSS in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: T=25 C,VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency=38.4 MHz. RF center frequency 2.445 GHz. Test circuit according to Figure 5.2 EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) on page 64 and Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65. Table 4.16. RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 1% PER SAT Signal is reference signal1. Packet length is 20 octets. -- 10 -- dBm Sensitivity, 1% PER2 SENS Signal is reference signal. Packet length is 20 octets. Using DC-DC converter. -- -99 -- dBm Signal is reference signal. Packet length is 20 octets. Without DCDC converter. -- -99 -- dBm Co-channel interferer rejection, 1% PER CCR Desired signal 10 dB above sensitivity limit -- -2.6 -- dB High-side adjacent channel rejection, 1% PER. Desired is reference signal at 3dB above reference sensitivity level3 ACR+1 Interferer is reference signal at +1 channel-spacing. -- 33.75 -- dB Interferer is filtered reference signal4 at +1 channel-spacing. -- 52.2 -- dB Interferer is CW at +1 channelspacing.5 -- 58.6 -- dB Interferer is reference signal at -1 channel-spacing. -- 35 -- dB Interferer is filtered reference signal4 at -1 channel-spacing. -- 54.7 -- dB Interferer is CW at -1 channelspacing. -- 60.1 -- dB Interferer is reference signal at 2 channel-spacing -- 45.9 -- dB Interferer is filtered reference signal4 at 2 channel-spacing -- 56.8 -- dB Interferer is CW at 2 channelspacing -- 65.5 -- dB Image rejection , 1% PER, IR Desired is reference signal at 3dB above reference sensitivity level3 Interferer is CW in image band5 -- 49.3 -- dB Blocking rejection of all other BLOCK channels. 1% PER, Desired is reference signal at 3dB above reference sensitivity level3. Interferer is reference signal. Interferer frequency < Desired frequency - 3 channel-spacing -- 57.2 -- dB Interferer frequency > Desired frequency + 3 channel-spacing -- 57.9 -- dB Blocking rejection of 802.11g BLOCK80211G signal centered at +12MHz or -13MHz Desired is reference signal at 6dB above reference sensitivity level3 -- 51.6 -- dB Low-side adjacent channel rejection, 1% PER. Desired is reference signal at 3dB above reference sensitivity level3 Alternate channel rejection, 1% PER. Desired is reference signal at 3dB above reference sensitivity level3 ACR-1 ACR2 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 33 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Min Typ Max Unit Upper limit of input power RSSIMAX range over which RSSI resolution is maintained 5 -- -- dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -- -- -98 dBm -- 0.25 -- dB -- 1 -- dB RSSI resolution RSSIRES RSSI accuracy in the linear region as defined by 802.15.4-2003 RSSILIN Test Condition over RSSIMIN to RSSIMAX Note: 1. Reference signal is defined as O-QPSK DSSS per 802.15.4, Frequency range = 2400-2483.5 MHz, Symbol rate = 62.5 ksymbols/s 2. Receive sensitivity on 802.15.4 channel 14 is -98 dBm 3. Reference sensitivity level is -85 dBm 4. Filter is characterized as a symmetric bandpass centered on the adjacent channel having a 3dB bandwidth of 4.6 MHz and stopband rejection better than 26 dB beyond 3.15 MHz from the adjacent carrier. 5. Due to low-IF frequency, there is some overlap of adjacent channel and image channel bands. Adjacent channel CW blocker tests place the Interferer center frequency at the Desired frequency 5 MHz on the channel raster, whereas the image rejection test places the CW interferer near the image frequency of the Desired signal carrier, regardless of the channel raster. 4.1.10 Modem Features Table 4.17. Modem Features Parameter Symbol Test Condition Min Typ Max Unit Receive Bandwidth RXBandwidth Configurable range with 38.4 MHz crystal 0.1 -- 2530 kHz IF Frequency IFFreq Configurable range with 38.4 MHz crystal. Selected steps available. 150 -- 1371 kHz DSSS symbol length DSSSRange Configurable in steps of 1 chip 2 -- 32 chips DSSS Bits per symbol DSSSBitPerSym Configurable 1 -- 4 bits/ symbol silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 34 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.11 Oscillators 4.1.11.1 LFXO Table 4.18. LFXO Parameter Symbol Crystal frequency Test Condition Min Typ Max Unit fLFXO -- 32.768 -- kHz Supported crystal equivalent series resistance (ESR) ESRLFXO -- -- 70 k Supported range of crystal load capacitance 1 CLFXO_CL 6 -- 18 pF On-chip tuning cap range 2 CLFXO_T 8 -- 40 pF On-chip tuning cap step size SSLFXO -- 0.25 -- pF Current consumption after startup 3 ILFXO ESR = 70 k, CL = 7 pF, GAIN4 = 3, AGC4 = 1 -- 273 -- nA Start- up time tLFXO ESR=70 k, CL=7 pF, GAIN4 =2 -- 308 -- ms On each of LFXTAL_N and LFXTAL_P pins Note: 1. Total load capacitance as seen by the crystal 2. The effective load capacitance seen by the crystal will be CLFXO_T /2. This is because each XTAL pin has a tuning cap and the two caps will be seen in series by the crystal. 3. Block is supplied by AVDD if ANASW = 0, or DVDD if ANASW=1 in EMU_PWRCTRL register 4. In CMU_LFXOCTRL register silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 35 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.11.2 HFXO Table 4.19. HFXO Parameter Symbol Crystal Frequency fHFXO Supported crystal equivalent series resistance (ESR) ESRHFXO Supported range of crystal load capacitance 1 CHFXO_CL On-chip tuning cap range 2 CHFXO_T On-chip tuning capacitance step SSHFXO Startup time tHFXO Frequency Tolerance for the crystal FTHFXO Test Condition Min Typ Max Unit 38 38.4 40 MHz -- -- 60 6 -- 12 pF 9 20 25 pF -- 0.04 -- pF 38.4 MHz, ESR = 50 , CL = 10 pF -- 300 -- s 38.4 MHz, ESR = 50 , CL = 10 pF -40 -- 40 ppm Crystal frequency 38.4 MHz On each of HFXTAL_N and HFXTAL_P pins Note: 1. Total load capacitance as seen by the crystal 2. The effective load capacitance seen by the crystal will be CHFXO_T /2. This is because each XTAL pin has a tuning cap and the two caps will be seen in series by the crystal. 4.1.11.3 LFRCO Table 4.20. LFRCO Parameter Symbol Test Condition Oscillation frequency fLFRCO Startup time tLFRCO Current consumption 1 ILFRCO Min Typ Max Unit ENVREF = 1 in CMU_LFRCOCTRL, TAMB 85 C 30.474 32.768 34.243 kHz ENVREF = 1 in CMU_LFRCOCTRL, TAMB > 85 C 30.474 -- 39.7 kHz ENVREF = 0 in CMU_LFRCOCTRL 30.474 32.768 33.915 kHz -- 500 -- s ENVREF = 1 in CMU_LFRCOCTRL -- 342 -- nA ENVREF = 0 in CMU_LFRCOCTRL -- 494 -- nA Note: 1. Block is supplied by AVDD if ANASW = 0, or DVDD if ANASW=1 in EMU_PWRCTRL register silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 36 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.11.4 HFRCO and AUXHFRCO Table 4.21. HFRCO and AUXHFRCO Parameter Symbol Test Condition Min Typ Max Unit Frequency Accuracy fHFRCO Any frequency band, across supply voltage and temperature -2.5 -- 2.5 % Start-up time tHFRCO fHFRCO 19 MHz -- 300 -- ns 4 < fHFRCO < 19 MHz -- 1 -- s fHFRCO 4 MHz -- 2.5 -- s fHFRCO = 38 MHz -- 204 228 A fHFRCO = 32 MHz -- 171 190 A fHFRCO = 26 MHz -- 147 164 A fHFRCO = 19 MHz -- 126 138 A fHFRCO = 16 MHz -- 110 120 A fHFRCO = 13 MHz -- 100 110 A fHFRCO = 7 MHz -- 81 91 A fHFRCO = 4 MHz -- 33 35 A fHFRCO = 2 MHz -- 31 35 A fHFRCO = 1 MHz -- 30 35 A Coarse (% of period) -- 0.8 -- % Fine (% of period) -- 0.1 -- % -- 0.2 -- % RMS Min Typ Max Unit 0.95 1 1.07 kHz Current consumption on all supplies Step size Period Jitter IHFRCO SSHFRCO PJHFRCO 4.1.11.5 ULFRCO Table 4.22. ULFRCO Parameter Symbol Oscillation frequency fULFRCO silabs.com | Smart. Connected. Energy-friendly. Test Condition Rev. 1.0 | 37 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.12 Primary Flash Memory Characteristics Table 4.23. Primary Flash Memory Characteristics1 Parameter Symbol Flash erase cycles before failure ECFLASH Flash data retention RETFLASH Test Condition Min Typ Max Unit 10000 -- -- cycles TAMB 85 C 10 -- -- years TAMB 125 C 10 -- -- years Word (32-bit) programming time tW_PROG 20 26 40 s Page erase time tPERASE 20 27 40 ms Mass erase time tMERASE 20 27 40 ms Device erase time2 tDERASE TAMB 85 C -- 60 74 ms TAMB 125 C -- 60 78 ms -- -- 3 mA -- -- 5 mA -- -- 3 mA Page erase current3 IERASE Mass or Device erase current3 Write current3 IWRITE Note: 1. Flash data retention information is published in the Quarterly Quality and Reliability Report. 2. Device erase is issued over the AAP interface and erases all flash, SRAM, the Lock Bit (LB) page, and the User data page Lock Word (ULW) 3. Measured at 25C 4.1.13 Serial Flash Memory Characteristics Table 4.24. Serial Flash Memory Characteristics Parameter Symbol Serial flash erase cycles before failure ECSFLASH Serial flash data retention RETSFLASH Page Program Time tPPROG Erase Time tERASE silabs.com | Smart. Connected. Energy-friendly. Test Condition Min Typ Max Unit 100000 -- -- cycles 20 -- -- years 1 to 256 Bytes -- 0.5 0.8 ms 4 kByte Sector -- 70 300 ms 32 kByte Block -- 130 500 ms 64 kByte Block -- 200 1000 ms Full Erase -- 1.5 3 s Rev. 1.0 | 38 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.14 GPIO Table 4.25. GPIO Parameter Symbol Input low voltage Test Condition Min Typ Max Unit VIOIL -- -- IOVDD*0.3 V Input high voltage VIOIH IOVDD*0.7 -- -- V Output high voltage relative to IOVDD VIOOH IOVDD*0.8 -- -- V IOVDD*0.6 -- -- V IOVDD*0.8 -- -- V IOVDD*0.6 -- -- V -- -- IOVDD*0.2 V -- -- IOVDD*0.4 V -- -- IOVDD*0.2 V -- -- IOVDD*0.4 V All GPIO except LFXO pins, GPIO IOVDD, Tamb 85 C -- 0.1 30 nA LFXO Pins, GPIO IOVDD, Tamb 85 C -- 0.1 50 nA All GPIO except LFXO pins, GPIO IOVDD, TAMB > 85 C -- -- 110 nA LFXO Pins, GPIO IOVDD, TAMB > 85 C -- -- 250 nA IOVDD < GPIO IOVDD + 2 V -- 3.3 15 A Sourcing 3 mA, IOVDD 3 V, DRIVESTRENGTH1 = WEAK Sourcing 1.2 mA, IOVDD 2.3 V, DRIVESTRENGTH1 = WEAK Sourcing 20 mA, IOVDD 3 V, DRIVESTRENGTH1 = STRONG Sourcing 8 mA, IOVDD 2.3 V, DRIVESTRENGTH1 = STRONG Output low voltage relative to VIOOL IOVDD Sinking 3 mA, IOVDD 3 V, DRIVESTRENGTH1 = WEAK Sinking 1.2 mA, IOVDD 2.3 V, DRIVESTRENGTH1 = WEAK Sinking 20 mA, IOVDD 3 V, DRIVESTRENGTH1 = STRONG Sinking 8 mA, IOVDD 2.3 V, DRIVESTRENGTH1 = STRONG Input leakage current IIOLEAK Input leakage current on 5VTOL pads above IOVDD I5VTOLLEAK I/O pin pull-up resistor RPU 30 43 65 k I/O pin pull-down resistor RPD 30 43 65 k 20 25 35 ns Pulse width of pulses retIOGLITCH moved by the glitch suppression filter silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 39 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Output fall time, From 70% to 30% of VIO tIOOF CL = 50 pF, Min Typ Max Unit -- 1.8 -- ns -- 4.5 -- ns -- 2.2 -- ns -- 7.4 -- ns Min Typ Max Unit DRIVESTRENGTH1 = STRONG, SLEWRATE1 = 0x6 CL = 50 pF, DRIVESTRENGTH1 = WEAK, SLEWRATE1 = 0x6 Output rise time, From 30% to 70% of VIO tIOOR CL = 50 pF, DRIVESTRENGTH1 = STRONG, SLEWRATE = 0x61 CL = 50 pF, DRIVESTRENGTH1 = WEAK, SLEWRATE1 = 0x6 Note: 1. In GPIO_Pn_CTRL register 4.1.15 VMON Table 4.26. VMON Parameter Symbol Test Condition VMON Supply Current IVMON In EM0 or EM1, 1 supply monitored -- 5.8 8.26 A In EM0 or EM1, 4 supplies monitored -- 11.8 16.8 A In EM2, EM3 or EM4, 1 supply monitored -- 62 -- nA In EM2, EM3 or EM4, 4 supplies monitored -- 99 -- nA In EM0 or EM1 -- 2 -- A In EM2, EM3 or EM4 -- 2 -- nA 1.62 -- 3.4 V Coarse -- 200 -- mV Fine -- 20 -- mV Supply drops at 1V/s rate -- 460 -- ns -- 26 -- mV VMON Loading of Monitored ISENSE Supply Threshold range VVMON_RANGE Threshold step size NVMON_STESP Response time tVMON_RES Hysteresis VVMON_HYST silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 40 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.16 ADC Table 4.27. ADC Parameter Symbol Resolution VRESOLUTION Input voltage range VADCIN Test Condition Single ended Differential Input range of external refer- VADCREFIN_P ence voltage, single ended and differential Min Typ Max Unit 6 -- 12 Bits 0 -- 2*VREF V -VREF -- VREF V 1 -- VAVDD V Power supply rejection1 PSRRADC At DC -- 80 -- dB Analog input common mode rejection ratio CMRRADC At DC -- 80 -- dB 1 Msps / 16 MHz ADCCLK, -- 301 350 A 250 ksps / 4 MHz ADCCLK, BIASPROG = 6, GPBIASACC = 1 3 -- 149 -- A 62.5 ksps / 1 MHz ADCCLK, -- 91 -- A -- 51 -- A -- 9 -- A -- 117 -- A -- 79 -- A -- 345 -- A 250 ksps / 4 MHz ADCCLK, BIASPROG = 6, GPBIASACC = 0 3 -- 191 -- A 62.5 ksps / 1 MHz ADCCLK, -- 132 -- A Current from all supplies, us- IADC_CONTIing internal reference buffer. NOUS_LP Continous operation. WARMUPMODE2 = KEEPADCWARM BIASPROG = 0, GPBIASACC = 1 3 BIASPROG = 15, GPBIASACC = 13 Current from all supplies, us- IADC_NORMAL_LP 35 ksps / 16 MHz ADCCLK, ing internal reference buffer. BIASPROG = 0, GPBIASACC = 1 Duty-cycled operation. WAR3 2 MUPMODE = NORMAL 5 ksps / 16 MHz ADCCLK BIASPROG = 0, GPBIASACC = 1 3 Current from all supplies, us- IADC_STANDing internal reference buffer. BY_LP Duty-cycled operation. AWARMUPMODE2 = KEEPINSTANDBY or KEEPINSLOWACC 125 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 1 3 35 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 1 3 Current from all supplies, us- IADC_CONTIing internal reference buffer. NOUS_HP Continous operation. WARMUPMODE2 = KEEPADCWARM 1 Msps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 0 3 BIASPROG = 15, GPBIASACC = 03 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 41 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Current from all supplies, us- IADC_NORMAL_HP 35 ksps / 16 MHz ADCCLK, ing internal reference buffer. BIASPROG = 0, GPBIASACC = 0 Duty-cycled operation. WAR3 2 MUPMODE = NORMAL 5 ksps / 16 MHz ADCCLK Min Typ Max Unit -- 102 -- A -- 17 -- A -- 162 -- A -- 123 -- A -- 140 -- A BIASPROG = 0, GPBIASACC = 0 3 Current from all supplies, us- IADC_STANDing internal reference buffer. BY_HP Duty-cycled operation. AWARMUPMODE2 = KEEPINSTANDBY or KEEPINSLOWACC 125 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 0 3 35 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 0 3 Current from HFPERCLK IADC_CLK ADC Clock Frequency fADCCLK -- -- 16 MHz Throughput rate fADCRATE -- -- 1 Msps Conversion time4 tADCCONV 6 bit -- 7 -- cycles 8 bit -- 9 -- cycles 12 bit -- 13 -- cycles WARMUPMODE2 = NORMAL -- -- 5 s WARMUPMODE2 = KEEPINSTANDBY -- -- 2 s WARMUPMODE2 = KEEPINSLOWACC -- -- 1 s Internal reference, 2.5 V full-scale, differential (-1.25, 1.25) 58 67 -- dB vrefp_in = 1.25 V direct mode with 2.5 V full-scale, differential -- 68 -- dB Startup time of reference generator and ADC core SNDR at 1Msps and fin = 10kHz tADCSTART SNDRADC HFPERCLK = 16 MHz Spurious-Free Dynamic Range (SFDR) SFDRADC 1 MSamples/s, 10 kHz full-scale sine wave -- 75 -- dB Input referred ADC noise, rms VREF_NOISE Including quantization noise and distortion -- 380 -- V Offset Error VADCOFFSETERR -3 0.25 3 LSB Gain error in ADC VADC_GAIN Using internal reference -- -0.2 5 % Using external reference -- -1 -- % Differential non-linearity (DNL) DNLADC 12 bit resolution -1 -- 2 LSB Integral non-linearity (INL), End point method INLADC 12 bit resolution -6 -- 6 LSB Temperature Sensor Slope VTS_SLOPE -- -1.84 -- mV/C silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 42 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. PSRR is referenced to AVDD when ANASW=0 and to DVDD when ANASW=1 in EMU_PWRCTRL 2. In ADCn_CNTL register 3. In ADCn_BIASPROG register 4. Derived from ADCCLK silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 43 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.17 IDAC Table 4.28. IDAC Parameter Symbol Number of Ranges NIDAC_RANGES Output Current IIDAC_OUT Linear steps within each range NIDAC_STEPS Step size SSIDAC Total Accuracy, STEPSEL1 = ACCIDAC 0x10 Start up time tIDAC_SU silabs.com | Smart. Connected. Energy-friendly. Test Condition Min Typ Max Unit -- 4 -- - RANGSEL1 = RANGE0 0.05 -- 1.6 A RANGSEL1 = RANGE1 1.6 -- 4.7 A RANGSEL1 = RANGE2 0.5 -- 16 A RANGSEL1 = RANGE3 2 -- 64 A -- 32 -- RANGSEL1 = RANGE0 -- 50 -- nA RANGSEL1 = RANGE1 -- 100 -- nA RANGSEL1 = RANGE2 -- 500 -- nA RANGSEL1 = RANGE3 -- 2 -- A EM0 or EM1, AVDD=3.3 V, T = 25 C -2 -- 2 % EM0 or EM1 -18 -- 22 % EM2 or EM3, Source mode, RANGSEL1 = RANGE0, AVDD=3.3 V, T = 25 C -- -2 -- % EM2 or EM3, Source mode, RANGSEL1 = RANGE1, AVDD=3.3 V, T = 25 C -- -1.7 -- % EM2 or EM3, Source mode, RANGSEL1 = RANGE2, AVDD=3.3 V, T = 25 C -- -0.8 -- % EM2 or EM3, Source mode, RANGSEL1 = RANGE3, AVDD=3.3 V, T = 25 C -- -0.5 -- % EM2 or EM3, Sink mode, RANGSEL1 = RANGE0, AVDD=3.3 V, T = 25 C -- -0.7 -- % EM2 or EM3, Sink mode, RANGSEL1 = RANGE1, AVDD=3.3 V, T = 25 C -- -0.6 -- % EM2 or EM3, Sink mode, RANGSEL1 = RANGE2, AVDD=3.3 V, T = 25 C -- -0.5 -- % EM2 or EM3, Sink mode, RANGSEL1 = RANGE3, AVDD=3.3 V, T = 25 C -- -0.5 -- % Output within 1% of steady state value -- 5 -- s Rev. 1.0 | 44 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Settling time, (output settled tIDAC_SETTLE within 1% of steady state value) Range setting is changed -- 5 -- s Step value is changed -- 1 -- s Current consumption in EM0 IIDAC or EM1 2 Source mode, excluding output current -- 8.9 13 A Sink mode, excluding output current -- 12 16 A Source mode, excluding output current, duty cycle mode, T = 25 C -- 1.04 -- A Sink mode, excluding output current, duty cycle mode, T = 25 C -- 1.08 -- A Source mode, excluding output current, duty cycle mode, T 85 C -- 8.9 -- A Sink mode, excluding output current, duty cycle mode, T 85 C -- 12 -- A RANGESEL1=0, output voltage = min(VIOVDD, VAVDD2-100 mv) -- 0.04 -- % RANGESEL1=1, output voltage = min(VIOVDD, VAVDD2-100 mV) -- 0.02 -- % RANGESEL1=2, output voltage = min(VIOVDD, VAVDD2-150 mV) -- 0.02 -- % RANGESEL1=3, output voltage = min(VIOVDD, VAVDD2-250 mV) -- 0.02 -- % RANGESEL1=0, output voltage = 100 mV -- 0.18 -- % RANGESEL1=1, output voltage = 100 mV -- 0.12 -- % RANGESEL1=2, output voltage = 150 mV -- 0.08 -- % RANGESEL1=3, output voltage = 250 mV -- 0.02 -- % Current consumption in EM2 or EM32 Output voltage compliance in ICOMP_SRC source mode, source current change relative to current sourced at 0 V Output voltage compliance in ICOMP_SINK sink mode, sink current change relative to current sunk at IOVDD Note: 1. In IDAC_CURPROG register 2. The IDAC is supplied by either AVDD, DVDD, or IOVDD based on the setting of ANASW in the EMU_PWRCTRL register and PWRSEL in the IDAC_CTRL register. Setting PWRSEL to 1 selects IOVDD. With PWRSEL cleared to 0, ANASW selects between AVDD (0) and DVDD (1). silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 45 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.18 Analog Comparator (ACMP) Table 4.29. ACMP Parameter Symbol Test Condition Input voltage range VACMPIN ACMPVDD = ACMPn_CTRL_PWRSEL 1 Supply Voltage VACMPVDD Active current not including voltage reference IACMP Current consumption of inter- IACMPREF nal voltage reference Hysteresis (VCM = 1.25 V, BIASPROG2 = 0x10, FULLBIAS2 = 1) VACMPHYST silabs.com | Smart. Connected. Energy-friendly. Min Typ Max Unit 0 -- VACMPVDD V BIASPROG2 0x10 or FULLBIAS2 = 0 1.85 -- VVREGVDD_ V 0x10 < BIASPROG2 0x20 and FULLBIAS2 = 1 2.1 BIASPROG2 = 1, FULLBIAS2 = 0 -- 50 -- nA BIASPROG2 = 0x10, FULLBIAS2 =0 -- 306 -- nA BIASPROG2 = 0x20, FULLBIAS2 =1 -- 74 95 A VLP selected as input using 2.5 V Reference / 4 (0.625 V) -- 50 -- nA VLP selected as input using VDD -- 20 -- nA VBDIV selected as input using 1.25 V reference / 1 -- 4.1 -- A VADIV selected as input using VDD/1 -- 2.4 -- A HYSTSEL3 = HYST0 -1.75 0 1.75 mV HYSTSEL3 = HYST1 10 18 26 mV HYSTSEL3 = HYST2 21 32 46 mV HYSTSEL3 = HYST3 27 44 63 mV HYSTSEL3 = HYST4 32 55 80 mV HYSTSEL3 = HYST5 38 65 100 mV HYSTSEL3 = HYST6 43 77 121 mV HYSTSEL3 = HYST7 47 86 148 mV HYSTSEL3 = HYST8 -4 0 4 mV HYSTSEL3 = HYST9 -27 -18 -10 mV HYSTSEL3 = HYST10 -47 -32 -18 mV HYSTSEL3 = HYST11 -64 -43 -27 mV HYSTSEL3 = HYST12 -78 -54 -32 mV HYSTSEL3 = HYST13 -93 -64 -37 mV HYSTSEL3 = HYST14 -113 -74 -42 mV HYSTSEL3 = HYST15 -135 -85 -47 mV MAX -- VVREGVDD_ V MAX Rev. 1.0 | 46 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Comparator delay4 tACMPDELAY BIASPROG2 = 1, FULLBIAS2 = 0 -- 30 -- s BIASPROG2 = 0x10, FULLBIAS2 =0 -- 3.7 -- s BIASPROG2 = 0x20, FULLBIAS2 =1 -- 35 -- ns -35 -- 35 mV Offset voltage VACMPOFFSET BIASPROG2 =0x10, FULLBIAS2 =1 Reference Voltage VACMPREF Internal 1.25 V reference 1 1.25 1.47 V Internal 2.5 V reference 2 2.5 2.8 V CSRESSEL5 = 0 -- inf -- k CSRESSEL5 = 1 -- 15 -- k CSRESSEL5 = 2 -- 27 -- k CSRESSEL5 = 3 -- 39 -- k CSRESSEL5 = 4 -- 51 -- k CSRESSEL5 = 5 -- 102 -- k CSRESSEL5 = 6 -- 164 -- k CSRESSEL5 = 7 -- 239 -- k Capacitive Sense Internal Resistance RCSRES Note: 1. ACMPVDD is a supply chosen by the setting in ACMPn_CTRL_PWRSEL and may be IOVDD, AVDD or DVDD 2. In ACMPn_CTRL register 3. In ACMPn_HYSTERESIS register 4. 100 mV differential drive 5. In ACMPn_INPUTSEL register The total ACMP current is the sum of the contributions from the ACMP and its internal voltage reference as given as: IACMPTOTAL = IACMP + IACMPREF IACMPREF is zero if an external voltage reference is used. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 47 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.19 I2C I2C Standard-mode (Sm) Table 4.30. I2C Standard-mode (Sm)1 Parameter Symbol SCL clock frequency2 Test Condition Min Typ Max Unit fSCL 0 -- 100 kHz SCL clock low time tLOW 4.7 -- -- s SCL clock high time tHIGH 4 -- -- s SDA set-up time tSU,DAT 250 -- -- ns SDA hold time3 tHD,DAT 100 -- 3450 ns Repeated START condition set-up time tSU,STA 4.7 -- -- s (Repeated) START condition tHD,STA hold time 4 -- -- s STOP condition set-up time tSU,STO 4 -- -- s Bus free time between a STOP and START condition tBUF 4.7 -- -- s Note: 1. For CLHR set to 0 in the I2Cn_CTRL register 2. For the minimum HFPERCLK frequency required in Standard-mode, refer to the I2C chapter in the reference manual 3. The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW) silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 48 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications I2C Fast-mode (Fm) Table 4.31. I2C Fast-mode (Fm)1 Parameter Symbol SCL clock frequency2 Test Condition Min Typ Max Unit fSCL 0 -- 400 kHz SCL clock low time tLOW 1.3 -- -- s SCL clock high time tHIGH 0.6 -- -- s SDA set-up time tSU,DAT 100 -- -- ns SDA hold time3 tHD,DAT 100 -- 900 ns Repeated START condition set-up time tSU,STA 0.6 -- -- s (Repeated) START condition tHD,STA hold time 0.6 -- -- s STOP condition set-up time tSU,STO 0.6 -- -- s Bus free time between a STOP and START condition tBUF 1.3 -- -- s Note: 1. For CLHR set to 1 in the I2Cn_CTRL register 2. For the minimum HFPERCLK frequency required in Fast-mode, refer to the I2C chapter in the reference manual 3. The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW) I2C Fast-mode Plus (Fm+) Table 4.32. I2C Fast-mode Plus (Fm+)1 Parameter Symbol SCL clock frequency2 Test Condition Min Typ Max Unit fSCL 0 -- 1000 kHz SCL clock low time tLOW 0.5 -- -- s SCL clock high time tHIGH 0.26 -- -- s SDA set-up time tSU,DAT 50 -- -- ns SDA hold time tHD,DAT 100 -- -- ns Repeated START condition set-up time tSU,STA 0.26 -- -- s (Repeated) START condition tHD,STA hold time 0.26 -- -- s STOP condition set-up time tSU,STO 0.26 -- -- s Bus free time between a STOP and START condition tBUF 0.5 -- -- s Note: 1. For CLHR set to 0 or 1 in the I2Cn_CTRL register 2. For the minimum HFPERCLK frequency required in Fast-mode Plus, refer to the I2C chapter in the reference manual silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 49 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.1.20 USART SPI SPI Master Timing Table 4.33. SPI Master Timing Parameter Symbol SCLK period 1 2 tSCLK CS to MOSI 1 2 Test Condition Min Typ Max Unit 2* tHFPERCLK -- -- ns tCS_MO 0 -- 8 ns SCLK to MOSI 1 2 tSCLK_MO 3 -- 20 ns MISO setup time 1 2 tSU_MI IOVDD = 2.3 V 56 -- -- ns IOVDD = 3.0 V 37 -- -- ns 6 -- -- ns tH_MI MISO hold time 1 2 Note: 1. Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0) 2. Measurement done with 8 pF output loading at 10% and 90% of VDD (figure shows 50% of VDD) CS tCS_MO tSCKL_MO SCLK CLKPOL = 0 tSCLK SCLK CLKPOL = 1 MOSI tSU_MI tH_MI MISO Figure 4.1. SPI Master Timing Diagram silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 50 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications SPI Slave Timing Table 4.34. SPI Slave Timing Parameter Symbol SCKL period 1 2 Test Condition Min Typ Max Unit tSCLK_sl 2* tHFPERCLK -- -- ns SCLK high period1 2 tSCLK_hi 3* tHFPERCLK -- -- ns SCLK low period 1 2 tSCLK_lo 3* tHFPERCLK -- -- ns CS active to MISO 1 2 tCS_ACT_MI 4 -- 50 ns CS disable to MISO 1 2 tCS_DIS_MI 4 -- 50 ns MOSI setup time 1 2 tSU_MO 4 -- -- ns MOSI hold time 1 2 tH_MO 3+2* tHFPERCLK -- -- ns SCLK to MISO 1 2 tSCLK_MI 16 + tHFPERCLK -- 66 + 2 * tHFPERCLK ns Note: 1. Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0) 2. Measurement done with 8 pF output loading at 10% and 90% of VDD (figure shows 50% of VDD) CS tCS_ACT_MI tCS_DIS_MI SCLK CLKPOL = 0 SCLK CLKPOL = 1 tSCLK_HI tSU_MO tSCLK_LO tSCLK tH_MO MOSI tSCLK_MI MISO Figure 4.2. SPI Slave Timing Diagram 4.2 Typical Performance Curves Typical performance curves indicate typical characterized performance under the stated conditions. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 51 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.2.1 Supply Current Figure 4.3. EM0 Active Mode Typical Supply Current Figure 4.4. EM1 Sleep Mode Typical Supply Current Typical supply current for EM2, EM3 and EM4H using standard software libraries from Silicon Laboratories. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 52 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.5. EM2, EM3, EM4H and EM4S Typical Supply Current silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 53 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.2.2 DC-DC Converter Default test conditions: CCM mode, LDCDC = 4.7 H, CDCDC = 1.0 F, VDCDC_I = 3.3 V, VDCDC_O = 1.8 V, FDCDC_LN = 7 MHz Figure 4.6. DC-DC Converter Typical Performance Characteristics silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 54 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Load Step Response in LN (CCM) mode (Heavy Drive) LN (CCM) and LP mode transition (load: 5mA) DVDD DVDD 60mV/div offset:1.8V 50mV/div offset:1.8V 100mA VSW ILOAD 2V/div offset:1.8V 1mA 100s/div 10s/div Figure 4.7. DC-DC Converter Transition Waveforms silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 55 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.2.3 Internal Oscillators Figure 4.8. HFRCO and AUXHFRCO Typical Performance at 38 MHz Figure 4.9. HFRCO and AUXHFRCO Typical Performance at 32 MHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 56 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.10. HFRCO and AUXHFRCO Typical Performance at 26 MHz Figure 4.11. HFRCO and AUXHFRCO Typical Performance at 19 MHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 57 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.12. HFRCO and AUXHFRCO Typical Performance at 16 MHz Figure 4.13. HFRCO and AUXHFRCO Typical Performance at 13 MHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 58 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.14. HFRCO and AUXHFRCO Typical Performance at 7 MHz Figure 4.15. HFRCO and AUXHFRCO Typical Performance at 4 MHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 59 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.16. HFRCO and AUXHFRCO Typical Performance at 2 MHz Figure 4.17. HFRCO and AUXHFRCO Typical Performance at 1 MHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 60 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.18. LFRCO Typical Performance at 32.768 kHz Figure 4.19. ULFRCO Typical Performance at 1 kHz silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 61 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications 4.2.4 2.4 GHz Radio Figure 4.20. 2.4 GHz RF Transmitter Output Power silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 62 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Electrical Specifications Figure 4.21. 2.4 GHz RF Receiver Sensitivity silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 63 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Typical Connection Diagrams 5. Typical Connection Diagrams 5.1 Power Typical power supply connections for direct supply, without using the internal DC-DC converter, are shown in the following figure. VDD Main Supply + - VREGVDD AVDD VREGSW IOVDD HFXTAL_N VREGVSS HFXTAL_P DVDD LFXTAL_N LFXTAL_P DECOUPLE RFVDD PAVDD Figure 5.1. EFR32MG1 Typical Application Circuit: Direct Supply Configuration without DC-DC converter Typical power supply circuits using the internal DC-DC converter are shown below. The MCU operates from the DC-DC converter supply. For low RF transmit power applications less than 13dBm, the RF PA may be supplied by the DC-DC converter. For OPNs supporting high power RF transmission, the RF PA must be directly supplied by VDD for RF transmit power greater than 13 dBm. VDD Main Supply + - VREGVDD VDCDC AVDD VREGSW IOVDD HFXTAL_N VREGVSS HFXTAL_P DVDD LFXTAL_N LFXTAL_P DECOUPLE RFVDD PAVDD Figure 5.2. EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 64 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Typical Connection Diagrams VDD Main Supply + - VREGVDD VDCDC AVDD VREGSW IOVDD HFXTAL_N VREGVSS HFXTAL_P DVDD LFXTAL_N LFXTAL_P DECOUPLE RFVDD PAVDD Figure 5.3. EFR32MG1 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDD) 5.2 RF Matching Networks Typical RF matching network circuit diagrams are shown in Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 65 for applications in the 2.4GHz band. Application-specific component values can be found in the EFR32 Reference Manual. For low RF transmit power applications less than 13dBm, the two-element match is recommended. For OPNs supporting high power RF transmission, the four-element match is recommended for high RF transmit power (> 13dBm). 4-Element Match for 2.4GHz Band 2-Element Match for 2.4GHz Band PAVDD PAVDD PAVDD 2G4RF_IOP 2G4RF_ION PAVDD L0 50 C0 L0 L1 50 2G4RF_IOP 2G4RF_ION C0 C1 Figure 5.4. Typical 2.4 GHz RF impedance-matching network circuits 5.3 Other Connections Other components or connections may be required to meet the system-level requirements. Application Note AN0002: "Hardware Design Considerations" contains detailed information on these connections. Application Notes can be accessed on the Silicon Labs website (www.silabs.com/32bit-appnotes). silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 65 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions 6. Pin Definitions 6.1 EFR32MG1 QFN32 2.4 GHz Definition Figure 6.1. EFR32MG1 QFN32 2.4 GHz Pinout silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 66 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Table 6.1. QFN32 2.4 GHz Device Pinout QFN32 Pin# and Name Pin # Pin Name 0 VSS 1 2 3 PF0 PF1 PF2 Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #24 TIM0_CC1 #23 TIM0_CC2 #22 TIM0_CDTI0 #21 TIM0_CDTI1 #20 TIM0_CDTI2 #19 TIM1_CC0 #24 TIM1_CC1 #23 TIM1_CC2 #22 TIM1_CC3 #21 LETIM0_OUT0 #24 LETIM0_OUT1 #23 PCNT0_S0IN #24 PCNT0_S1IN #23 US0_TX #24 US0_RX #23 US0_CLK #22 US0_CS #21 US0_CTS #20 US0_RTS #19 LEU0_TX #24 LEU0_RX #23 I2C0_SDA #24 I2C0_SCL #23 FRC_DCLK #24 FRC_DOUT #23 FRC_DFRAME #22 MODEM_DCLK #24 MODEM_DIN #23 MODEM_DOUT #22 MODEM_ANT0 #21 MODEM_ANT1 #20 PRS_CH0 #0 PRS_CH1 #7 PRS_CH2 #6 PRS_CH3 #5 ACMP0_O #24 ACMP1_O #24 DBG_SWCLKTCK #0 TIM0_CC0 #25 TIM0_CC1 #24 TIM0_CC2 #23 TIM0_CDTI0 #22 TIM0_CDTI1 #21 TIM0_CDTI2 #20 TIM1_CC0 #25 TIM1_CC1 #24 TIM1_CC2 #23 TIM1_CC3 #22 LETIM0_OUT0 #25 LETIM0_OUT1 #24 PCNT0_S0IN #25 PCNT0_S1IN #24 US0_TX #25 US0_RX #24 US0_CLK #23 US0_CS #22 US0_CTS #21 US0_RTS #20 LEU0_TX #25 LEU0_RX #24 I2C0_SDA #25 I2C0_SCL #24 FRC_DCLK #25 FRC_DOUT #24 FRC_DFRAME #23 MODEM_DCLK #25 MODEM_DIN #24 MODEM_DOUT #23 MODEM_ANT0 #22 MODEM_ANT1 #21 PRS_CH0 #1 PRS_CH1 #0 PRS_CH2 #7 PRS_CH3 #6 ACMP0_O #25 ACMP1_O #25 DBG_SWDIOTMS #0 TIM0_CC0 #26 TIM0_CC1 #25 TIM0_CC2 #24 TIM0_CDTI0 #23 TIM0_CDTI1 #22 TIM0_CDTI2 #21 TIM1_CC0 #26 TIM1_CC1 #25 TIM1_CC2 #24 TIM1_CC3 #23 LETIM0_OUT0 #26 LETIM0_OUT1 #25 PCNT0_S0IN #26 PCNT0_S1IN #25 US0_TX #26 US0_RX #25 US0_CLK #24 US0_CS #23 US0_CTS #22 US0_RTS #21 LEU0_TX #26 LEU0_RX #25 I2C0_SDA #26 I2C0_SCL #25 FRC_DCLK #26 FRC_DOUT #25 FRC_DFRAME #24 MODEM_DCLK #26 MODEM_DIN #25 MODEM_DOUT #24 MODEM_ANT0 #23 MODEM_ANT1 #22 CMU_CLK0 #6 PRS_CH0 #2 PRS_CH1 #1 PRS_CH2 #0 PRS_CH3 #7 ACMP0_O #26 ACMP1_O #26 DBG_TDO #0 DBG_SWO #0 GPIO_EM4WU0 Ground BUSAX [ADC0: APORT1XCH16 ACMP0: APORT1XCH16 ACMP1: APORT1XCH16] BUSBY [ADC0: APORT2YCH16 ACMP0: APORT2YCH16 ACMP1: APORT2YCH16] BUSAY [ADC0: APORT1YCH17 ACMP0: APORT1YCH17 ACMP1: APORT1YCH17] BUSBX [ADC0: APORT2XCH17 ACMP0: APORT2XCH17 ACMP1: APORT2XCH17] BUSAX [ADC0: APORT1XCH18 ACMP0: APORT1XCH18 ACMP1: APORT1XCH18] BUSBY [ADC0: APORT2YCH18 ACMP0: APORT2YCH18 ACMP1: APORT2YCH18] silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 67 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions QFN32 Pin# and Name Pin # Pin Name Pin Alternate Functionality / Description Analog BUSAY [ADC0: APORT1YCH19 ACMP0: APORT1YCH19 ACMP1: APORT1YCH19] Timers Communication Radio Other TIM0_CC0 #27 TIM0_CC1 #26 TIM0_CC2 #25 TIM0_CDTI0 #24 TIM0_CDTI1 #23 TIM0_CDTI2 #22 TIM1_CC0 #27 TIM1_CC1 #26 TIM1_CC2 #25 TIM1_CC3 #24 LETIM0_OUT0 #27 LETIM0_OUT1 #26 PCNT0_S0IN #27 PCNT0_S1IN #26 US0_TX #27 US0_RX #26 US0_CLK #25 US0_CS #24 US0_CTS #23 US0_RTS #22 LEU0_TX #27 LEU0_RX #26 I2C0_SDA #27 I2C0_SCL #26 FRC_DCLK #27 FRC_DOUT #26 FRC_DFRAME #25 MODEM_DCLK #27 MODEM_DIN #26 MODEM_DOUT #25 MODEM_ANT0 #24 MODEM_ANT1 #23 CMU_CLK1 #6 PRS_CH0 #3 PRS_CH1 #2 PRS_CH2 #1 PRS_CH3 #0 ACMP0_O #27 ACMP1_O #27 DBG_TDI #0 4 PF3 5 RFVDD 6 HFXTAL_N High Frequency Crystal input pin. 7 HFXTAL_P High Frequency Crystal output pin. 8 RESETn Reset input, active low.To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. 9 RFVSS Radio Ground 10 PAVSS Power Amplifier (PA) voltage regulator VSS 11 2G4RF_ION 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 12 2G4RF_IOP 2.4 GHz Differential RF input/output, positive path. 13 PAVDD Power Amplifier (PA) voltage regulator VDD input 14 PD13 BUSBX [ADC0: APORT2XCH19 ACMP0: APORT2XCH19 ACMP1: APORT2XCH19] Radio power supply BUSCY [ADC0: APORT3YCH5 ACMP0: APORT3YCH5 ACMP1: APORT3YCH5 IDAC0: APORT1YCH5] BUSDX [ADC0: APORT4XCH5 ACMP0: APORT4XCH5 ACMP1: APORT4XCH5] silabs.com | Smart. Connected. Energy-friendly. TIM0_CC0 #21 TIM0_CC1 #20 TIM0_CC2 #19 TIM0_CDTI0 #18 TIM0_CDTI1 #17 TIM0_CDTI2 #16 TIM1_CC0 #21 TIM1_CC1 #20 TIM1_CC2 #19 TIM1_CC3 #18 LETIM0_OUT0 #21 LETIM0_OUT1 #20 PCNT0_S0IN #21 PCNT0_S1IN #20 US0_TX #21 US0_RX #20 US0_CLK #19 US0_CS #18 US0_CTS #17 US0_RTS #16 LEU0_TX #21 LEU0_RX #20 I2C0_SDA #21 I2C0_SCL #20 FRC_DCLK #21 FRC_DOUT #20 FRC_DFRAME #19 MODEM_DCLK #21 MODEM_DIN #20 MODEM_DOUT #19 MODEM_ANT0 #18 MODEM_ANT1 #17 PRS_CH3 #12 PRS_CH4 #4 PRS_CH5 #3 PRS_CH6 #15 ACMP0_O #21 ACMP1_O #21 Rev. 1.0 | 68 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions QFN32 Pin# and Name Pin # 15 Pin Alternate Functionality / Description Pin Name Analog Timers Communication Radio Other PD14 BUSCX [ADC0: APORT3XCH6 ACMP0: APORT3XCH6 ACMP1: APORT3XCH6 IDAC0: APORT1XCH6] TIM0_CC0 #22 TIM0_CC1 #21 TIM0_CC2 #20 TIM0_CDTI0 #19 TIM0_CDTI1 #18 TIM0_CDTI2 #17 TIM1_CC0 #22 TIM1_CC1 #21 TIM1_CC2 #20 TIM1_CC3 #19 LETIM0_OUT0 #22 LETIM0_OUT1 #21 PCNT0_S0IN #22 PCNT0_S1IN #21 US0_TX #22 US0_RX #21 US0_CLK #20 US0_CS #19 US0_CTS #18 US0_RTS #17 LEU0_TX #22 LEU0_RX #21 I2C0_SDA #22 I2C0_SCL #21 FRC_DCLK #22 FRC_DOUT #21 FRC_DFRAME #20 MODEM_DCLK #22 MODEM_DIN #21 MODEM_DOUT #20 MODEM_ANT0 #19 MODEM_ANT1 #18 CMU_CLK0 #5 PRS_CH3 #13 PRS_CH4 #5 PRS_CH5 #4 PRS_CH6 #16 ACMP0_O #22 ACMP1_O #22 GPIO_EM4WU4 TIM0_CC0 #23 TIM0_CC1 #22 TIM0_CC2 #21 TIM0_CDTI0 #20 TIM0_CDTI1 #19 TIM0_CDTI2 #18 TIM1_CC0 #23 TIM1_CC1 #22 TIM1_CC2 #21 TIM1_CC3 #20 LETIM0_OUT0 #23 LETIM0_OUT1 #22 PCNT0_S0IN #23 PCNT0_S1IN #22 US0_TX #23 US0_RX #22 US0_CLK #21 US0_CS #20 US0_CTS #19 US0_RTS #18 LEU0_TX #23 LEU0_RX #22 I2C0_SDA #23 I2C0_SCL #22 FRC_DCLK #23 FRC_DOUT #22 FRC_DFRAME #21 MODEM_DCLK #23 MODEM_DIN #22 MODEM_DOUT #21 MODEM_ANT0 #20 MODEM_ANT1 #19 CMU_CLK1 #5 PRS_CH3 #14 PRS_CH4 #6 PRS_CH5 #5 PRS_CH6 #17 ACMP0_O #23 ACMP1_O #23 DBG_SWO #2 TIM0_CC0 #0 TIM0_CC1 #31 TIM0_CC2 #30 TIM0_CDTI0 #29 TIM0_CDTI1 #28 TIM0_CDTI2 #27 TIM1_CC0 #0 TIM1_CC1 #31 TIM1_CC2 #30 TIM1_CC3 #29 LETIM0_OUT0 #0 LETIM0_OUT1 #31 PCNT0_S0IN #0 PCNT0_S1IN #31 US0_TX #0 US0_RX #31 US0_CLK #30 US0_CS #29 US0_CTS #28 US0_RTS #27 LEU0_TX #0 LEU0_RX #31 I2C0_SDA #0 I2C0_SCL #31 FRC_DCLK #0 FRC_DOUT #31 FRC_DFRAME #30 MODEM_DCLK #0 MODEM_DIN #31 MODEM_DOUT #30 MODEM_ANT0 #29 MODEM_ANT1 #28 CMU_CLK1 #0 PRS_CH6 #0 PRS_CH7 #10 PRS_CH8 #9 PRS_CH9 #8 ACMP0_O #0 ACMP1_O #0 BUSDY [ADC0: APORT4YCH6 ACMP0: APORT4YCH6 ACMP1: APORT4YCH6] 16 PD15 BUSCY [ADC0: APORT3YCH7 ACMP0: APORT3YCH7 ACMP1: APORT3YCH7 IDAC0: APORT1YCH7] BUSDX [ADC0: APORT4XCH7 ACMP0: APORT4XCH7 ACMP1: APORT4XCH7] ADC0_EXTN 17 PA0 BUSCX [ADC0: APORT3XCH8 ACMP0: APORT3XCH8 ACMP1: APORT3XCH8 IDAC0: APORT1XCH8] BUSDY [ADC0: APORT4YCH8 ACMP0: APORT4YCH8 ACMP1: APORT4YCH8] silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 69 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions QFN32 Pin# and Name Pin # Pin Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #1 TIM0_CC1 #0 TIM0_CC2 #31 TIM0_CDTI0 #30 TIM0_CDTI1 #29 TIM0_CDTI2 #28 TIM1_CC0 #1 TIM1_CC1 #0 TIM1_CC2 #31 TIM1_CC3 #30 LETIM0_OUT0 #1 LETIM0_OUT1 #0 PCNT0_S0IN #1 PCNT0_S1IN #0 US0_TX #1 US0_RX #0 US0_CLK #31 US0_CS #30 US0_CTS #29 US0_RTS #28 LEU0_TX #1 LEU0_RX #0 I2C0_SDA #1 I2C0_SCL #0 FRC_DCLK #1 FRC_DOUT #0 FRC_DFRAME #31 MODEM_DCLK #1 MODEM_DIN #0 MODEM_DOUT #31 MODEM_ANT0 #30 MODEM_ANT1 #29 CMU_CLK0 #0 PRS_CH6 #1 PRS_CH7 #0 PRS_CH8 #10 PRS_CH9 #9 ACMP0_O #1 ACMP1_O #1 TIM0_CC0 #6 TIM0_CC1 #5 TIM0_CC2 #4 TIM0_CDTI0 #3 TIM0_CDTI1 #2 TIM0_CDTI2 #1 TIM1_CC0 #6 TIM1_CC1 #5 TIM1_CC2 #4 TIM1_CC3 #3 LETIM0_OUT0 #6 LETIM0_OUT1 #5 PCNT0_S0IN #6 PCNT0_S1IN #5 US0_TX #6 US0_RX #5 US0_CLK #4 US0_CS #3 US0_CTS #2 US0_RTS #1 LEU0_TX #6 LEU0_RX #5 I2C0_SDA #6 I2C0_SCL #5 FRC_DCLK #6 FRC_DOUT #5 FRC_DFRAME #4 MODEM_DCLK #6 MODEM_DIN #5 MODEM_DOUT #4 MODEM_ANT0 #3 MODEM_ANT1 #2 PRS_CH6 #6 PRS_CH7 #5 PRS_CH8 #4 PRS_CH9 #3 ACMP0_O #6 ACMP1_O #6 TIM0_CC0 #7 TIM0_CC1 #6 TIM0_CC2 #5 TIM0_CDTI0 #4 TIM0_CDTI1 #3 TIM0_CDTI2 #2 TIM1_CC0 #7 TIM1_CC1 #6 TIM1_CC2 #5 TIM1_CC3 #4 LETIM0_OUT0 #7 LETIM0_OUT1 #6 PCNT0_S0IN #7 PCNT0_S1IN #6 US0_TX #7 US0_RX #6 US0_CLK #5 US0_CS #4 US0_CTS #3 US0_RTS #2 LEU0_TX #7 LEU0_RX #6 I2C0_SDA #7 I2C0_SCL #6 FRC_DCLK #7 FRC_DOUT #6 FRC_DFRAME #5 MODEM_DCLK #7 MODEM_DIN #6 MODEM_DOUT #5 MODEM_ANT0 #4 MODEM_ANT1 #3 PRS_CH6 #7 PRS_CH7 #6 PRS_CH8 #5 PRS_CH9 #4 ACMP0_O #7 ACMP1_O #7 ADC0_EXTP 18 PA1 BUSCY [ADC0: APORT3YCH9 ACMP0: APORT3YCH9 ACMP1: APORT3YCH9 IDAC0: APORT1YCH9] BUSDX [ADC0: APORT4XCH9 ACMP0: APORT4XCH9 ACMP1: APORT4XCH9] 19 PB11 BUSCY [ADC0: APORT3YCH27 ACMP0: APORT3YCH27 ACMP1: APORT3YCH27 IDAC0: APORT1YCH27] BUSDX [ADC0: APORT4XCH27 ACMP0: APORT4XCH27 ACMP1: APORT4XCH27] 20 PB12 BUSCX [ADC0: APORT3XCH28 ACMP0: APORT3XCH28 ACMP1: APORT3XCH28 IDAC0: APORT1XCH28] BUSDY [ADC0: APORT4YCH28 ACMP0: APORT4YCH28 ACMP1: APORT4YCH28] silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 70 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions QFN32 Pin# and Name Pin # 21 Pin Alternate Functionality / Description Pin Name Analog Timers Communication Radio Other PB13 BUSCY [ADC0: APORT3YCH29 ACMP0: APORT3YCH29 ACMP1: APORT3YCH29 IDAC0: APORT1YCH29] TIM0_CC0 #8 TIM0_CC1 #7 TIM0_CC2 #6 TIM0_CDTI0 #5 TIM0_CDTI1 #4 TIM0_CDTI2 #3 TIM1_CC0 #8 TIM1_CC1 #7 TIM1_CC2 #6 TIM1_CC3 #5 LETIM0_OUT0 #8 LETIM0_OUT1 #7 PCNT0_S0IN #8 PCNT0_S1IN #7 US0_TX #8 US0_RX #7 US0_CLK #6 US0_CS #5 US0_CTS #4 US0_RTS #3 LEU0_TX #8 LEU0_RX #7 I2C0_SDA #8 I2C0_SCL #7 FRC_DCLK #8 FRC_DOUT #7 FRC_DFRAME #6 MODEM_DCLK #8 MODEM_DIN #7 MODEM_DOUT #6 MODEM_ANT0 #5 MODEM_ANT1 #4 PRS_CH6 #8 PRS_CH7 #7 PRS_CH8 #6 PRS_CH9 #5 ACMP0_O #8 ACMP1_O #8 DBG_SWO #1 GPIO_EM4WU9 TIM0_CC0 #9 TIM0_CC1 #8 TIM0_CC2 #7 TIM0_CDTI0 #6 TIM0_CDTI1 #5 TIM0_CDTI2 #4 TIM1_CC0 #9 TIM1_CC1 #8 TIM1_CC2 #7 TIM1_CC3 #6 LETIM0_OUT0 #9 LETIM0_OUT1 #8 PCNT0_S0IN #9 PCNT0_S1IN #8 US0_TX #9 US0_RX #8 US0_CLK #7 US0_CS #6 US0_CTS #5 US0_RTS #4 LEU0_TX #9 LEU0_RX #8 I2C0_SDA #9 I2C0_SCL #8 FRC_DCLK #9 FRC_DOUT #8 FRC_DFRAME #7 MODEM_DCLK #9 MODEM_DIN #8 MODEM_DOUT #7 MODEM_ANT0 #6 MODEM_ANT1 #5 CMU_CLK1 #1 PRS_CH6 #9 PRS_CH7 #8 PRS_CH8 #7 PRS_CH9 #6 ACMP0_O #9 ACMP1_O #9 TIM0_CC0 #10 TIM0_CC1 #9 TIM0_CC2 #8 TIM0_CDTI0 #7 TIM0_CDTI1 #6 TIM0_CDTI2 #5 TIM1_CC0 #10 TIM1_CC1 #9 TIM1_CC2 #8 TIM1_CC3 #7 LETIM0_OUT0 #10 LETIM0_OUT1 #9 PCNT0_S0IN #10 PCNT0_S1IN #9 US0_TX #10 US0_RX #9 US0_CLK #8 US0_CS #7 US0_CTS #6 US0_RTS #5 LEU0_TX #10 LEU0_RX #9 I2C0_SDA #10 I2C0_SCL #9 FRC_DCLK #10 FRC_DOUT #9 FRC_DFRAME #8 MODEM_DCLK #10 MODEM_DIN #9 MODEM_DOUT #8 MODEM_ANT0 #7 MODEM_ANT1 #6 CMU_CLK0 #1 PRS_CH6 #10 PRS_CH7 #9 PRS_CH8 #8 PRS_CH9 #7 ACMP0_O #10 ACMP1_O #10 BUSDX [ADC0: APORT4XCH29 ACMP0: APORT4XCH29 ACMP1: APORT4XCH29] 22 AVDD Analog power supply. LFXTAL_N 23 PB14 BUSCX [ADC0: APORT3XCH30 ACMP0: APORT3XCH30 ACMP1: APORT3XCH30 IDAC0: APORT1XCH30] BUSDY [ADC0: APORT4YCH30 ACMP0: APORT4YCH30 ACMP1: APORT4YCH30] LFXTAL_P 24 PB15 BUSCY [ADC0: APORT3YCH31 ACMP0: APORT3YCH31 ACMP1: APORT3YCH31 IDAC0: APORT1YCH31] BUSDX [ADC0: APORT4XCH31 ACMP0: APORT4XCH31 ACMP1: APORT4XCH31] 25 VREGVSS Voltage regulator VSS 26 VREGSW DCDC regulator switching node 27 VREGVDD Voltage regulator VDD input 28 DVDD 29 DECOUPLE Digital power supply. Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 71 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions QFN32 Pin# and Name Pin # Pin Name 30 IOVDD 31 32 PC10 PC11 Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #15 TIM0_CC1 #14 TIM0_CC2 #13 TIM0_CDTI0 #12 TIM0_CDTI1 #11 TIM0_CDTI2 #10 TIM1_CC0 #15 TIM1_CC1 #14 TIM1_CC2 #13 TIM1_CC3 #12 LETIM0_OUT0 #15 LETIM0_OUT1 #14 PCNT0_S0IN #15 PCNT0_S1IN #14 US0_TX #15 US0_RX #14 US0_CLK #13 US0_CS #12 US0_CTS #11 US0_RTS #10 LEU0_TX #15 LEU0_RX #14 I2C0_SDA #15 I2C0_SCL #14 FRC_DCLK #15 FRC_DOUT #14 FRC_DFRAME #13 MODEM_DCLK #15 MODEM_DIN #14 MODEM_DOUT #13 MODEM_ANT0 #12 MODEM_ANT1 #11 CMU_CLK1 #3 PRS_CH0 #12 PRS_CH9 #15 PRS_CH10 #4 PRS_CH11 #3 ACMP0_O #15 ACMP1_O #15 GPIO_EM4WU12 TIM0_CC0 #16 TIM0_CC1 #15 TIM0_CC2 #14 TIM0_CDTI0 #13 TIM0_CDTI1 #12 TIM0_CDTI2 #11 TIM1_CC0 #16 TIM1_CC1 #15 TIM1_CC2 #14 TIM1_CC3 #13 LETIM0_OUT0 #16 LETIM0_OUT1 #15 PCNT0_S0IN #16 PCNT0_S1IN #15 US0_TX #16 US0_RX #15 US0_CLK #14 US0_CS #13 US0_CTS #12 US0_RTS #11 LEU0_TX #16 LEU0_RX #15 I2C0_SDA #16 I2C0_SCL #15 FRC_DCLK #16 FRC_DOUT #15 FRC_DFRAME #14 MODEM_DCLK #16 MODEM_DIN #15 MODEM_DOUT #14 MODEM_ANT0 #13 MODEM_ANT1 #12 CMU_CLK0 #3 PRS_CH0 #13 PRS_CH9 #16 PRS_CH10 #5 PRS_CH11 #4 ACMP0_O #16 ACMP1_O #16 DBG_SWO #3 Digital IO power supply. BUSAX [ADC0: APORT1XCH10 ACMP0: APORT1XCH10 ACMP1: APORT1XCH10] BUSBY [ADC0: APORT2YCH10 ACMP0: APORT2YCH10 ACMP1: APORT2YCH10] BUSAY [ADC0: APORT1YCH11 ACMP0: APORT1YCH11 ACMP1: APORT1YCH11] BUSBX [ADC0: APORT2XCH11 ACMP0: APORT2XCH11 ACMP1: APORT2XCH11] silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 72 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions 6.1.1 EFR32MG1 QFN32 2.4 GHz GPIO Overview The GPIO pins are organized as 16-bit ports indicated by letters (A, B, C...), and the individual pins on each port are indicated by a number from 15 down to 0. Table 6.2. QFN32 2.4 GHz GPIO Pinout Port Pin 15 Pin 14 Pin 13 Pin 12 Pin 11 Pin 10 Port A - - - - - - - - - - - - - - PA1 PA0 - - - - - - - - - - - - - - - - - - - - - Port B Port C Port D Port F PB15 PB14 - - PB13 PB12 PB11 (5V) (5V) (5V) - PD15 PD14 PD13 (5V) (5V) (5V) - - - - PC11 PC10 (5V) (5V) Pin 9 Pin 8 Pin 7 Pin 6 Pin 5 Pin 4 Pin 3 Pin 2 Pin 1 Pin 0 - - - - - - - - - - - - - - - - - - - - - - PF3 (5V) PF2 (5V) PF1 (5V) PF0 (5V) Note: 1. GPIO with 5V tolerance are indicated by (5V). 2. The pins PB13, PB12, PB11, PD15, PD14, and PD13 will not be 5V tolerant on all future devices. In order to preserve upgrade options with full hardware compatibility, do not use these pins with 5V domains. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 73 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions 6.2 Alternate Functionality Pinout A wide selection of alternate functionality is available for multiplexing to various pins. The following table shows the name of the alternate functionality in the first column, followed by columns showing the possible LOCATION bitfield settings. Note: Some functionality, such as analog interfaces, do not have alternate settings or a LOCATION bitfield. In these cases, the pinout is shown in the column corresponding to LOCATION 0. Table 6.3. Alternate functionality overview Alternate Functionality ACMP0_O ACMP1_O LOCATION 0-3 4-7 0: PA0 1: PA1 6: PB11 7: PB12 0: PA0 1: PA1 6: PB11 7: PB12 8: PB13 9: PB14 10: PB15 16 - 19 20 - 23 16: PC11 15: PC10 8: PB13 9: PB14 10: PB15 28 - 31 Description 21: PD13 22: PD14 23: PD15 24: PF0 25: PF1 26: PF2 27: PF3 Analog comparator ACMP0, digital output. 21: PD13 22: PD14 23: PD15 24: PF0 25: PF1 26: PF2 27: PF3 Analog comparator ACMP1, digital output. 16: PC11 15: PC10 24 - 27 Analog to digital converter ADC0 external reference input negative pin 0: PA1 Analog to digital converter ADC0 external reference input positive pin ADC0_EXTP 0: PA1 1: PB15 5: PD14 6: PF2 Clock Management Unit, clock output number 0. 5: PD15 6: PF3 Clock Management Unit, clock output number 1. 3: PC11 CMU_CLK1 12 - 15 0: PA0 ADC0_EXTN CMU_CLK0 8 - 11 0: PA0 1: PB14 3: PC10 0: PF0 DBG_SWCLKTCK Debug-interface Serial Wire clock input and JTAG Test Clock. Note that this function is enabled to the pin out of reset, and has a built-in pull down. 0: PF1 DBG_SWDIOTMS silabs.com | Smart. Connected. Energy-friendly. Debug-interface Serial Wire data input / output and JTAG Test Mode Select. Note that this function is enabled to the pin out of reset, and has a built-in pull up. Rev. 1.0 | 74 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Alternate Functionality DBG_SWO LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 Debug-interface Serial Wire viewer Output. 0: PF2 1: PB13 2: PD15 3: PC11 Note that this function is not enabled after reset, and must be enabled by software to be used. Debug-interface JTAG Test Data In. 0: PF3 Note that this function is enabled to pin out of reset, and has a built-in pull up. DBG_TDI Debug-interface JTAG Test Data Out. 0: PF2 DBG_TDO FRC_DCLK Description Note that this function is enabled to pin out of reset. 0: PA0 1: PA1 6: PB11 7: PB12 4: PB11 5: PB12 6: PB13 7: PB14 FRC_DFRAME 0: PA1 5: PB11 6: PB12 7: PB13 FRC_DOUT 0: PF2 GPIO_EM4WU0 0: PD14 GPIO_EM4WU4 0: PB13 GPIO_EM4WU9 0: PC10 GPIO_EM4WU12 silabs.com | Smart. Connected. Energy-friendly. 8: PB13 9: PB14 10: PB15 16: PC11 21: PD13 22: PD14 23: PD15 15: PC10 8: PB15 13: PC10 14: PC11 19: PD13 8: PB14 9: PB15 14: PC10 15: PC11 24: PF0 25: PF1 26: PF2 27: PF3 20: PD14 21: PD15 22: PF0 23: PF1 24: PF2 25: PF3 20: PD13 21: PD14 22: PD15 23: PF0 24: PF1 25: PF2 26: PF3 Frame Controller, Data Sniffer Clock. 30: PA0 31: PA1 31: PA0 Frame Controller, Data Sniffer Frame active Frame Controller, Data Sniffer Output. Pin can be used to wake the system up from EM4 Pin can be used to wake the system up from EM4 Pin can be used to wake the system up from EM4 Pin can be used to wake the system up from EM4 Rev. 1.0 | 75 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 0: PA1 5: PB11 6: PB12 7: PB13 I2C0_SCL I2C0_SDA LETIM0_OUT0 0: PA0 1: PA1 6: PB11 7: PB12 0: PA0 1: PA1 6: PB11 7: PB12 0: PA1 5: PB11 6: PB12 7: PB13 LETIM0_OUT1 0: PA1 5: PB11 6: PB12 7: PB13 LEU0_RX LEU0_TX 0: PA0 1: PA1 6: PB11 7: PB12 8 - 11 12 - 15 16 - 19 8: PB14 9: PB15 20: PD13 21: PD14 22: PD15 23: PF0 14: PC10 15: PC11 8: PB13 9: PB14 10: PB15 20 - 23 16: PC11 24 - 27 28 - 31 24: PF1 25: PF2 26: PF3 I2C0 Serial Clock Line input / output. 31: PA0 21: PD13 22: PD14 23: PD15 24: PF0 25: PF1 26: PF2 27: PF3 I2C0 Serial Data input / output. 15: PC10 21: PD13 22: PD14 23: PD15 24: PF0 25: PF1 26: PF2 27: PF3 Low Energy Timer LETIM0, output channel 0. 14: PC10 15: PC11 20: PD13 21: PD14 22: PD15 23: PF0 24: PF1 25: PF2 26: PF3 14: PC10 15: PC11 20: PD13 21: PD14 22: PD15 23: PF0 24: PF1 25: PF2 26: PF3 15: PC10 8: PB13 9: PB14 10: PB15 16: PC11 8: PB14 9: PB15 8: PB14 9: PB15 8: PB13 9: PB14 10: PB15 16: PC11 21: PD13 22: PD14 23: PD15 15: PC10 31: PA0 31: PA0 LEUART0 Transmit output. Also used as receive input in half duplex communication. 24: PF0 25: PF1 26: PF2 27: PF3 Low Frequency Crystal (typically 32.768 kHz) negative pin. Also used as an optional external clock input pin. LFXTAL_N 0: PB15 Low Frequency Crystal (typically 32.768 kHz) positive pin. LFXTAL_P 3: PB11 MODEM_ANT1 MODEM_DCLK 2: PB11 3: PB12 4: PB12 5: PB13 6: PB14 7: PB15 12: PC10 13: PC11 4: PB13 5: PB14 6: PB15 12: PC11 11: PC10 0: PA0 1: PA1 6: PB11 7: PB12 0: PA1 MODEM_DIN Low Energy Timer LETIM0, output channel 1. LEUART0 Receive input. 0: PB14 MODEM_ANT0 Description 5: PB11 6: PB12 7: PB13 silabs.com | Smart. Connected. Energy-friendly. 8: PB13 9: PB14 10: PB15 18: PD13 19: PD14 20: PD15 21: PF0 22: PF1 23: PF2 17: PD13 18: PD14 19: PD15 20: PF0 21: PF1 22: PF2 23: PF3 16: PC11 15: PC10 21: PD13 22: PD14 23: PD15 14: PC10 15: PC11 20: PD13 21: PD14 22: PD15 23: PF0 8: PB14 9: PB15 24: PF3 29: PA0 30: PA1 28: PA0 29: PA1 24: PF0 25: PF1 26: PF2 27: PF3 MODEM antenna control output 0, used for antenna diversity. MODEM antenna control output 1, used for antenna diversity. MODEM data clock out. 24: PF1 25: PF2 26: PF3 MODEM data in. 31: PA0 Rev. 1.0 | 76 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 MODEM_DOUT PCNT0_S0IN 4-7 8 - 11 4: PB11 5: PB12 6: PB13 7: PB14 8: PB15 0: PA0 1: PA1 6: PB11 7: PB12 0: PA1 5: PB11 6: PB12 7: PB13 PCNT0_S1IN PRS_CH0 PRS_CH1 12 - 15 16 - 19 20 - 23 19: PD13 20: PD14 21: PD15 22: PF0 23: PF1 13: PC10 14: PC11 8: PB13 9: PB14 10: PB15 16: PC11 15: PC10 21: PD13 22: PD14 23: PD15 14: PC10 15: PC11 20: PD13 21: PD14 22: PD15 23: PF0 8: PB14 9: PB15 0: PF0 1: PF1 2: PF2 3: PF3 12: PC10 13: PC11 0: PF1 1: PF2 2: PF3 0: PF3 12: PD13 13: PD14 14: PD15 5: PF0 6: PF1 7: PF2 6: PB11 7: PB12 0: PA1 5: PB11 6: PB12 7: PB13 PRS_CH7 8: PB13 9: PB14 10: PB15 8: PB14 9: PB15 10: PA0 PRS_CH8 8: PB15 9: PA0 10: PA1 PRS_CH9 4: PB12 5: PB13 6: PB14 7: PB15 8: PA0 9: PA1 silabs.com | Smart. Connected. Energy-friendly. 16: PD14 17: PD15 15: PD13 4: PB11 5: PB12 6: PB13 7: PB14 3: PB11 24: PF1 25: PF2 26: PF3 31: PA0 Pulse Counter PCNT0 input number 1. Peripheral Reflex System PRS, channel 5. 3: PD13 PRS_CH6 Pulse Counter PCNT0 input number 0. Peripheral Reflex System PRS, channel 4. 4: PD14 5: PD15 0: PA0 1: PA1 24: PF0 25: PF1 26: PF2 27: PF3 MODEM data out. Peripheral Reflex System PRS, channel 3. 4: PD13 5: PD14 6: PD15 PRS_CH5 30: PA0 31: PA1 Peripheral Reflex System PRS, channel 2. 6: PF0 7: PF1 PRS_CH4 24: PF2 25: PF3 Description Peripheral Reflex System PRS, channel 1. 0: PF2 1: PF3 PRS_CH3 28 - 31 Peripheral Reflex System PRS, channel 0. 7: PF0 PRS_CH2 24 - 27 Peripheral Reflex System PRS, channel 6. Peripheral Reflex System PRS, channel 7. Peripheral Reflex System PRS, channel 8. 16: PC11 15: PC10 Peripheral Reflex System PRS, channel 9. Rev. 1.0 | 77 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 4: PC10 5: PC11 PRS_CH10 Peripheral Reflex System PRS, channel 10. 4: PC11 Peripheral Reflex System PRS, channel 11. PRS_CH11 3: PC10 TIM0_CC0 0: PA0 1: PA1 6: PB11 7: PB12 0: PA1 5: PB11 6: PB12 7: PB13 TIM0_CC1 4: PB11 5: PB12 6: PB13 7: PB14 TIM0_CC2 TIM0_CDTI0 3: PB11 TIM0_CDTI1 TIM0_CDTI2 TIM1_CC0 2: PB11 3: PB12 1: PB11 2: PB12 3: PB13 TIM1_CC3 3: PB11 US0_CLK 14: PC10 15: PC11 20: PD13 21: PD14 22: PD15 23: PF0 24: PF1 25: PF2 26: PF3 24: PF2 25: PF3 19: PD13 20: PD14 21: PD15 22: PF0 23: PF1 24: PF3 18: PD13 19: PD14 20: PD15 21: PF0 22: PF1 23: PF2 20: PF0 21: PF1 22: PF2 23: PF3 28: PA0 29: PA1 11: PC10 17: PD13 18: PD14 19: PD15 20: PF1 21: PF2 22: PF3 28: PA1 10: PC10 11: PC11 16: PD13 17: PD14 18: PD15 19: PF0 8: PB14 9: PB15 8: PB15 13: PC10 14: PC11 4: PB14 5: PB15 4: PB11 5: PB12 6: PB13 7: PB14 8: PB13 9: PB14 10: PB15 silabs.com | Smart. Connected. Energy-friendly. 31: PA0 30: PA0 31: PA1 29: PA0 30: PA1 27: PA0 16: PC11 24: PF0 25: PF1 26: PF2 27: PF3 15: PC10 21: PD13 22: PD14 23: PD15 14: PC10 15: PC11 20: PD13 21: PD14 22: PD15 23: PF0 24: PF1 25: PF2 26: PF3 24: PF2 25: PF3 19: PD13 20: PD14 21: PD15 22: PF0 23: PF1 24: PF3 18: PD13 19: PD14 20: PD15 21: PF0 22: PF1 23: PF2 24: PF2 25: PF3 19: PD13 20: PD14 21: PD15 22: PF0 23: PF1 8: PB14 9: PB15 8: PB15 13: PC10 14: PC11 4: PB12 5: PB13 6: PB14 7: PB15 4: PB11 5: PB12 6: PB13 7: PB14 Timer 0 Capture Compare input / output channel 0. 15: PC10 12: PC11 5: PB11 6: PB12 7: PB13 24: PF0 25: PF1 26: PF2 27: PF3 21: PD13 22: PD14 23: PD15 4: PB13 5: PB14 6: PB15 0: PA1 TIM1_CC2 16: PC11 12: PC10 13: PC11 6: PB11 7: PB12 TIM1_CC1 8: PB13 9: PB14 10: PB15 4: PB12 5: PB13 6: PB14 7: PB15 0: PA0 1: PA1 Description 12: PC10 13: PC11 8: PB15 13: PC10 14: PC11 Timer 0 Capture Compare input / output channel 1. Timer 0 Capture Compare input / output channel 2. Timer 0 Complimentary Dead Time Insertion channel 0. Timer 0 Complimentary Dead Time Insertion channel 1. Timer 0 Complimentary Dead Time Insertion channel 2. Timer 1 Capture Compare input / output channel 0. 31: PA0 30: PA0 31: PA1 29: PA0 30: PA1 30: PA0 31: PA1 Timer 1 Capture Compare input / output channel 1. Timer 1 Capture Compare input / output channel 2. Timer 1 Capture Compare input / output channel 3. USART0 clock input / output. Rev. 1.0 | 78 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 12: PC10 13: PC11 3: PB11 4: PB12 5: PB13 6: PB14 7: PB15 4: PB13 5: PB14 6: PB15 12: PC11 US0_CS US0_CTS US0_RTS 2: PB11 3: PB12 1: PB11 2: PB12 3: PB13 US0_TX 12 - 15 16 - 19 20 - 23 18: PD13 19: PD14 20: PD15 21: PF0 22: PF1 23: PF2 20: PF0 21: PF1 22: PF2 23: PF3 28: PA0 29: PA1 11: PC10 17: PD13 18: PD14 19: PD15 20: PF1 21: PF2 22: PF3 28: PA1 10: PC10 11: PC11 16: PD13 17: PD14 18: PD15 19: PF0 4: PB14 5: PB15 0: PA1 5: PB11 6: PB12 7: PB13 US0_RX 8 - 11 0: PA0 1: PA1 6: PB11 7: PB12 silabs.com | Smart. Connected. Energy-friendly. 8: PB14 9: PB15 8: PB13 9: PB14 10: PB15 16: PC11 15: PC10 28 - 31 21: PD13 22: PD14 23: PD15 Description 24: PF3 29: PA0 30: PA1 27: PA0 20: PD13 21: PD14 22: PD15 23: PF0 14: PC10 15: PC11 24 - 27 USART0 Clear To Send hardware flow control input. USART0 Request To Send hardware flow control output. USART0 Asynchronous Receive. 24: PF1 25: PF2 26: PF3 31: PA0 24: PF0 25: PF1 26: PF2 27: PF3 USART0 chip select input / output. USART0 Synchronous mode Master Input / Slave Output (MISO). USART0 Asynchronous Transmit. Also used as receive input in half duplex communication. USART0 Synchronous mode Master Output / Slave Input (MOSI). Rev. 1.0 | 79 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions 6.3 Analog Port (APORT) The Analog Port (APORT) is an infrastructure used to connect chip pins with on-chip analog clients such as analog comparators, ADCs, and DACs. The APORT consists of wires, switches, and control needed to configurably implement the routes. Please see the device Reference Manual for a complete description. PF0 PF2 PC10 BUSAX BUSBY PF1 PF3 PC11 BUSAY BUSBX PB14 PD14 PA0 PB12 BUSCX BUSDY PD13 PD15 PA1 PB11 PB13 PB15 BUSCY BUSDX 1X1Y2X2Y3X3Y4X4Y ACMP0 1X1Y2X2Y3X3Y4X4Y ACMP1 1X1Y2X2Y3X3Y4X4Y ADC0 1X1Y IDAC0 Figure 6.2. EFR32MG1 APORT Table 6.4. APORT Client Map Analog Module ACMP0 ACMP0 ACMP0 Analog Module Channel APORT1XCH10 Shared Bus BUSAX Pin PC10 APORT1XCH16 PF0 APORT1XCH18 PF2 APORT1YCH11 BUSAY PC11 APORT1YCH17 PF1 APORT1YCH19 PF3 APORT2XCH11 BUSBX PC11 APORT2XCH17 PF1 APORT2XCH19 PF3 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 80 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Analog Module ACMP0 ACMP0 ACMP0 ACMP0 ACMP0 ACMP1 ACMP1 ACMP1 ACMP1 Analog Module Channel APORT2YCH10 Shared Bus BUSBY Pin PC10 APORT2YCH16 PF0 APORT2YCH18 PF2 APORT3XCH6 BUSCX PD14 APORT3XCH8 PA0 APORT3XCH28 PB12 APORT3XCH30 PB14 APORT3YCH5 BUSCY PD13 APORT3YCH7 PD15 APORT3YCH9 PA1 APORT3YCH27 PB11 APORT3YCH29 PB13 APORT3YCH31 PB15 APORT4XCH5 BUSDX PD13 APORT4XCH7 PD15 APORT4XCH9 PA1 APORT4XCH27 PB11 APORT4XCH29 PB13 APORT4XCH31 PB15 APORT4YCH6 BUSDY PD14 APORT4YCH8 PA0 APORT4YCH28 PB12 APORT4YCH30 PB14 APORT1XCH10 BUSAX PC10 APORT1XCH16 PF0 APORT1XCH18 PF2 APORT1YCH11 BUSAY PC11 APORT1YCH17 PF1 APORT1YCH19 PF3 APORT2XCH11 BUSBX PC11 APORT2XCH17 PF1 APORT2XCH19 PF3 APORT2YCH10 BUSBY PC10 APORT2YCH16 PF0 APORT2YCH18 PF2 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 81 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Analog Module ACMP1 ACMP1 ACMP1 ACMP1 ADC0 ADC0 ADC0 ADC0 ADC0 Analog Module Channel APORT3XCH6 Shared Bus BUSCX Pin PD14 APORT3XCH8 PA0 APORT3XCH28 PB12 APORT3XCH30 PB14 APORT3YCH5 BUSCY PD13 APORT3YCH7 PD15 APORT3YCH9 PA1 APORT3YCH27 PB11 APORT3YCH29 PB13 APORT3YCH31 PB15 APORT4XCH5 BUSDX PD13 APORT4XCH7 PD15 APORT4XCH9 PA1 APORT4XCH27 PB11 APORT4XCH29 PB13 APORT4XCH31 PB15 APORT4YCH6 BUSDY PD14 APORT4YCH8 PA0 APORT4YCH28 PB12 APORT4YCH30 PB14 APORT1XCH10 BUSAX PC10 APORT1XCH16 PF0 APORT1XCH18 PF2 APORT1YCH11 BUSAY PC11 APORT1YCH17 PF1 APORT1YCH19 PF3 APORT2XCH11 BUSBX PC11 APORT2XCH17 PF1 APORT2XCH19 PF3 APORT2YCH10 BUSBY PC10 APORT2YCH16 PF0 APORT2YCH18 PF2 APORT3XCH6 BUSCX PD14 APORT3XCH8 PA0 APORT3XCH28 PB12 APORT3XCH30 PB14 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 82 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Pin Definitions Analog Module ADC0 ADC0 ADC0 IDAC0 IDAC0 Analog Module Channel APORT3YCH5 Shared Bus BUSCY Pin PD13 APORT3YCH7 PD15 APORT3YCH9 PA1 APORT3YCH27 PB11 APORT3YCH29 PB13 APORT3YCH31 PB15 APORT4XCH5 BUSDX PD13 APORT4XCH7 PD15 APORT4XCH9 PA1 APORT4XCH27 PB11 APORT4XCH29 PB13 APORT4XCH31 PB15 APORT4YCH6 BUSDY PD14 APORT4YCH8 PA0 APORT4YCH28 PB12 APORT4YCH30 PB14 APORT1XCH6 BUSCX PD14 APORT1XCH8 PA0 APORT1XCH28 PB12 APORT1XCH30 PB14 APORT1YCH5 BUSCY PD13 APORT1YCH7 PD15 APORT1YCH9 PA1 APORT1YCH27 PB11 APORT1YCH29 PB13 APORT1YCH31 PB15 silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 83 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet QFN32 Package Specifications 7. QFN32 Package Specifications 7.1 QFN32 Package Dimensions Figure 7.1. QFN32 Package Drawing silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 84 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet QFN32 Package Specifications Table 7.1. QFN32 Package Dimensions Dimension Min Typ Max A 0.80 0.85 0.90 A1 0.00 0.02 0.05 A3 0.20 REF b 0.18 0.25 0.30 D/E 4.90 5.00 5.10 D2/E2 3.40 3.50 3.60 E 0.50 BSC L 0.30 0.40 0.50 K 0.20 -- -- R 0.09 -- 0.14 aaa 0.15 bbb 0.10 ccc 0.10 ddd 0.05 eee 0.08 fff 0.10 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MO-220, Variation VKKD-4. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 85 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet QFN32 Package Specifications 7.2 QFN32 PCB Land Pattern Figure 7.2. QFN32 PCB Land Pattern Drawing silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 86 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet QFN32 Package Specifications Table 7.2. QFN32 PCB Land Pattern Dimensions Dimension Typ S1 4.01 S 4.01 L1 3.50 W1 3.50 e 0.50 W 0.26 L 0.86 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size can be 1:1 for all perimeter pads. 7. A 3x3 array of 0.85 mm square openings on a 1.00 mm pitch can be used for the center ground pad. 8. A No-Clean, Type-3 solder paste is recommended. 9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 87 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet QFN32 Package Specifications 7.3 QFN32 Package Marking EFR32 PPPPPPPPP YYWWTTTTTT Figure 7.3. QFN32 Package Marking The package marking consists of: * PPPPPPPPP - The part number designation. 1. Family Code (B | M | F) 2. G (Gecko) 3. Series (1, 2,...) 4. Performance Grade (P | B | V) 5. Feature Code (1 to 7) 6. TRX Code (3 = TXRX | 2= RX | 1 = TX) 7. Band (1 = Sub-GHz | 2 = 2.4 GHz | 3 = Dual-band) 8. Flash (G = 256K | F = 128K | E = 64K | D = 32K) 9. Temperature Grade (G = -40 to 85 | I = -40 to 125) * YY - The last 2 digits of the assembly year. * WW - The 2-digit workweek when the device was assembled. * TTTTTT - A trace or manufacturing code. The first letter is the device revision. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 88 EFR32MG1 Mighty Gecko SoC with Integrated Serial Flash Data Sheet Revision History 8. Revision History 8.1 Revision 1.0 2016-Jul-22 * Added -I temperature grade OPN's and associated sections * Electrical Characteristics: Minimum and maximum value statement changed to cover full operating temperature range. * Finalized Specification Tables. Tables with condition/min/typ/max or footnote changes include: * Absolute Maximum Ratings * General Operating Conditions * DC-DC Converter * Current Consumption Using Radio 3.3V with DC-DC * RF Transmitter General Characteristics for 2.4 GHz Band * RF Receiver General Characteristics for 2.4 GHz Band * RF Receiver Characteristics for Bluetooth Smart in the 2.4 GHz Band * RF Transmitter Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band * RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band * LFRCO * HFRCO and AUXHFRCO * Primary Flash Memory Characteristics * GPIO * ADC * IDAC * Updated Typical Performance Graphs. * Added external ground note to 2G4RF_ION pin descriptions. * Added note for 5V tolerance to pinout GPIO Overview sections. * Updated OPN decoder with latest revision. * Updated Package Marking text with latest descriptions. 8.2 Revision 0.95 2016-05-12 * All OPNs changed to rev C0. Note the following: * All OPNs ending in -B0 are Engineering Samples based on an older revision of silicon and are being removed from the OPN table. These older revisions should be used for evaluation only and will not be supported for production. * OPNs ending in -C0 are the Current Revision of Silicon and are intended for production. * Electrical specification tables updated with latest characterization data and production test limits. 8.3 Revision 0.2 2016-03-29 * Initial version. silabs.com | Smart. Connected. Energy-friendly. Rev. 1.0 | 89 Table of Contents 1. Feature List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.2 Radio. . . . . . . . . . . . 3.2.1 Antenna Interface . . . . . . . 3.2.2 Fractional-N Frequency Synthesizer. 3.2.3 Receiver Architecture. . . . . . 3.2.4 Transmitter Architecture . . . . . 3.2.5 Wake on Radio . . . . . . . . 3.2.6 RFSENSE . . . . . . . . . 3.2.7 Flexible Frame Handling. . . . . 3.2.8 Packet and State Trace . . . . . 3.2.9 Data Buffering . . . . . . . . 3.2.10 Radio Controller (RAC). . . . . 3.2.11 Random Number Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Power . . . . . . . . . . 3.3.1 Energy Management Unit (EMU) . 3.3.2 DC-DC Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 . 7 . 7 3.4 General Purpose Input/Output (GPIO). . . . . . . . . . . . . . . . . . . . . . 7 3.5 Clocking . . . . . . . . . . 3.5.1 Clock Management Unit (CMU) . 3.5.2 Internal and External Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 . 7 . 7 3.6 Counters/Timers and PWM . . . . . . . . 3.6.1 Timer/Counter (TIMER) . . . . . . . . . 3.6.2 Real Time Counter and Calendar (RTCC) . . . 3.6.3 Low Energy Timer (LETIMER). . . . . . . 3.6.4 Ultra Low Power Wake-up Timer (CRYOTIMER) 3.6.5 Pulse Counter (PCNT) . . . . . . . . . 3.6.6 Watchdog Timer (WDOG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 8 8 8 8 8 3.7 Communications and Other Digital Peripherals . . . . . . . . . 3.7.1 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) 3.7.2 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) 3.7.3 Inter-Integrated Circuit Interface (I2C) . . . . . . . . . . . 3.7.4 Peripheral Reflex System (PRS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 8 9 9 3.8 Security Features. . . . . . . . . . . . . . . 3.8.1 GPCRC (General Purpose Cyclic Redundancy Check) . 3.8.2 Crypto Accelerator (CRYPTO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 . 9 . 9 3.9 Analog . . . . . . . . . . . . . 3.9.1 Analog Port (APORT) . . . . . . . 3.9.2 Analog Comparator (ACMP) . . . . . 3.9.3 Analog to Digital Converter (ADC) . . . 3.9.4 Digital to Analog Current Converter (IDAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 . 9 . 9 . 9 .10 Table of Contents 90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 5 5 5 5 5 6 6 6 6 6 3.10 Reset Management Unit (RMU) . . . . . . . . . . . . . . . . .10 3.11 Core and Memory . . . . . . . . . . . 3.11.1 Processor Core . . . . . . . . . . . 3.11.2 Serial Flash . . . . . . . . . . . . 3.11.3 Memory System Controller (MSC) . . . . . 3.11.4 Linked Direct Memory Access Controller (LDMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 .10 .10 .10 .10 3.12 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3.13 Configuration Summary . . . . . . . . . . . . . . . . . . . . . . . . . .12 4. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . 4.1.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . 4.1.2 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . 4.1.2.1 General Operating Conditions . . . . . . . . . . . . . . . . . . 4.1.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . 4.1.4 DC-DC Converter . . . . . . . . . . . . . . . . . . . . . . . 4.1.5 Current Consumption. . . . . . . . . . . . . . . . . . . . . . 4.1.5.1 Current Consumption 3.3 V without DC-DC Converter . . . . . . . . . . 4.1.5.2 Current Consumption 3.3 V using DC-DC Converter . . . . . . . . . . 4.1.5.3 Current Consumption Using Radio . . . . . . . . . . . . . . . . 4.1.6 Wake up times . . . . . . . . . . . . . . . . . . . . . . . . 4.1.7 Brown Out Detector . . . . . . . . . . . . . . . . . . . . . . 4.1.8 Frequency Synthesizer Characteristics . . . . . . . . . . . . . . . . 4.1.9 2.4 GHz RF Transceiver Characteristics . . . . . . . . . . . . . . . 4.1.9.1 RF Transmitter General Characteristics for the 2.4 GHz Band . . . . . . . 4.1.9.2 RF Receiver General Characteristics for the 2.4 GHz Band . . . . . . . . 4.1.9.3 RF Transmitter Characteristics for Bluetooth Smart in the 2.4 GHz Band . . . . 4.1.9.4 RF Receiver Characteristics for Bluetooth Smart in the 2.4 GHz Band. . . . . 4.1.9.5 RF Transmitter Characteristics for 802.15.4 O-QPSK DSSS in the 2.4 GHz Band . 4.1.9.6 RF Receiver Characteristics for 802.15.4 O-QPSK DSSS in the 2.4 GHz Band. . 4.1.10 Modem Features . . . . . . . . . . . . . . . . . . . . . . . 4.1.11 Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.11.1 LFXO . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.11.2 HFXO . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.11.3 LFRCO . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.11.4 HFRCO and AUXHFRCO . . . . . . . . . . . . . . . . . . . 4.1.11.5 ULFRCO . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.12 Primary Flash Memory Characteristics . . . . . . . . . . . . . . . 4.1.13 Serial Flash Memory Characteristics . . . . . . . . . . . . . . . . 4.1.14 GPIO. . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.15 VMON . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.16 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.17 IDAC . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.18 Analog Comparator (ACMP) . . . . . . . . . . . . . . . . . . . 4.1.19 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.20 USART SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 .14 .15 .15 .16 .17 .19 .19 .20 .21 .22 .22 .23 .24 .24 .25 .26 .28 .30 .33 .34 .35 .35 .36 .36 .37 .37 .38 .38 .39 .40 .41 .44 .46 .48 .50 4.2 Typical Performance Curves . 4.2.1 Supply Current . . . . . 4.2.2 DC-DC Converter . . . . . . . . . . . . . . . . .51 .52 .54 Table of Contents 91 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.3 Internal Oscillators. 4.2.4 2.4 GHz Radio . . . . .56 .62 5. Typical Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . 64 5.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 5.2 RF Matching Networks . . . . . . . . . . . . . . . . . . . . . . . . . . .65 5.3 Other Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .65 6. Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 . 6.1 EFR32MG1 QFN32 2.4 GHz Definition . . . 6.1.1 EFR32MG1 QFN32 2.4 GHz GPIO Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 .73 6.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . . . .74 6.3 Analog Port (APORT) . . . . . . . . . . . . . . . . . . . . . . . . .80 7. QFN32 Package Specifications. . . . . . . . . . . . . . . . . . . . . . . . 84 . . 7.1 QFN32 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . .84 7.2 QFN32 PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . .86 7.3 QFN32 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . .88 8. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 8.1 Revision 1.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 8.2 Revision 0.95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 8.3 Revision 0.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Table of Contents 92 . Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! IoT Portfolio www.silabs.com/IoT SW/HW www.silabs.com/simplicity Quality www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.(R) , Silicon Laboratories(R), Silicon Labs(R), SiLabs(R) and the Silicon Labs logo(R), Bluegiga(R), Bluegiga Logo(R), Clockbuilder(R), CMEMS(R), DSPLL(R), EFM(R), EFM32(R), EFR, Ember(R), Energy Micro, Energy Micro logo and combinations thereof, "the world's most energy friendly microcontrollers", Ember(R), EZLink(R), EZRadio(R), EZRadioPRO(R), Gecko(R), ISOmodem(R), Precision32(R), ProSLIC(R), Simplicity Studio(R), SiPHY(R), Telegesis, the Telegesis Logo(R), USBXpress(R) and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com