AIB/GT Series AIB/GT Series is basically a MIL-DTL-5015 (MIL-C-5015) connector, but with an improved coupling system. AIB/GT Series replaces the threaded coupling used in MIL-DTL-5015 with a positive, quick-mating, 3-point reverse bayonet lock. AIB/GT Series shares the same shell dimensions, contact layouts, contacts, and performance characteristics as the MIL-DTL-5015 threaded connectors; however, the two series do not intermate. Over 180 contact layouts are available from 1 to 85 circuits and up to 150 amps per contact. The standard MIL-DTL-5015 layouts allow the mixing of power and signal contacts, power only, or signal only. Contacts are available in solder, crimp, or PC termination covering wire gauges from size 26 to size 0 AWG. Thermocouple (J, Y, K, T) and coax contacts are also available. These connectors are completely sealed to withstand moisture, condensation, vibration, and flash-over across a broad range of wire diameters. When the two connector halves are mated, the rear sealing grommet plus the dynamic interfacial seal at the front create an environmentally sealed assembly. Commercial and Military AIB/GT Series connectors are made in accordance with German military specification VG 95 234 and MIL-DTL-5015. Originally designed for NATO combat vehicles, aircraft, and airborne equipment, these rugged connectors are now widely used in a broad range of demanding commercial applications from trucks to industrial robots. Applications Industrial environments requiring extreme environmental reliability and ease of mating and unmating, such as: * * * * * Features AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series AIB/GT Series Power Generators Battery Systems Engines Sensors Motion Control * * * * Off-road Vehicles Earth Moving Equipment Ships Railroad Equipment * * * * Mobile Equipment Industrial Machinery Telecommunications Mass Transit Simple and Fast Mating and Un-mating AIB/GT Series connectors use a unique, "reverse bayonet" coupling system for ease of use. This system allows mating and un-mating of the connector halves with a simple 120 rotation - without compromising shock, vibration, or moisture resistance. The large, open ramps are easily cleaned of mud or other contaminants. The ramp coupling system eliminates the possibility of cross threading and thread damage possible with standard MIL-DTL-5015 threaded connectors. This quick-mating design is easier to mate in cold weather, tight spaces, or on equipment which must be disassembled frequently. Shock and Vibration Resistant AIB/GT Series connectors are supplied with standard military resistant sealing and 3-point bayonet coupling nut. The 3-point bayonet coupling incorporates a wave spring and washer which is specified by the Rail Industry. AIB/GT Series connectors pass the most stringent tests of shock and vibration performance while maintaining proper continuity and water tightness. Rugged aluminum alloy shell and hardware are light in weight yet highly resistant to damage. Proven Reliability AIB/GT Series connectors are used extensively in military vehicles such as the M1 Tank. They also have found applications on advanced locomotives, transit cars, and way maintenance equipment. Amphenol(R) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com 43 Specifications subject to change. Features AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Audible, Visual, and Tactile Confirmation of Mating AIB/GT Series connectors provide the user with three independent checks that the connector halves are mated. When the coupling nut is fully rotated, the three studs snap into the end of the ramps with a loud "click" (audible confirmation). At that same moment, the user can actually feel the bolts click into the grooves (tactile confirmation). Blue dots on the receptacle and on the coupling nut are aligned when the connector is properly mated (visual confirmation). Environmental The sealing of this connector is not compromised by any of the operating conditions defined in MIL-DTL-5015. The connector is completely watertight when mated. Broad Temperature Range These connectors will operate in temperatures from -67 to +257F (-55 to +125C). High temperature and zero halogen insulators are also available. Call for ordering information. Wide Range of Wire Gauges and Current Carrying Capability Up to 150 amps with accommodations for wire gauges from size 26 up to size 0 AWG wire. Wide Variety of Contacts High reliability screw machine contacts with silver or gold plating are available in sizes from 20 through 0 to accommodate wire gauges from 26 to 0 AWG. Solder, Crimp, PC, Coax, and Thermocouple contacts are available. AIB/GT Series connectors use rail industry standard crimp contacts which are completely interchangeable with other rail connectors such as Litton/Veam CIR series. Intermateable and Intermountable with all VG 95 234 Connectors The standard MIL-DTL-5015 layouts and dimensions ensure intermateability and intermountability with all connectors made in accordance with VG 95 234. All AIB/GT Series connectors are intermountable with standard threaded MIL-DTL-5015 connectors, making it possible to upgrade without the need to change panel cutouts or clearances in most cases. Technical Specifications MATERIALS & FINISHES Shell Aluminum alloy. (Shells can be grounded) Plating Olive drab chromate coating over cadmium plating, black zinc cobalt, electroless nickel, green zinc, and black anodized Contacts Copper alloy Platings Hard silver plating or gold plating Insulator* Neoprene Seals Silicone, Neoprene, or Viton** *Optional zero halogen and high temperature insulators are available. Call for information. **Viton is a registered trademark of DuPont DOW Elastomers 44 Amphenol(R) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Technical Specifications ELECTRICAL DATA Current Rating CONTACT SIZE TEST CURRENT (AMPS) 16/16S 12 8 4 0 13 23 46 (69)* 80 (80)* 150 (225)* AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Operating Voltage/Test Voltage The indicated values for the "operating voltage" According to MIL-DTL-5015 are limits concerning the electrical function. In any case, when the working voltage exceeds 50V, safety precautions must be in accordance with the following standards: VDE 0100, IEC 309-1 or applicable national standards *Test amps, multiconductor using Radsok contact Altitude Voltage Derating* Chart NOMINAL DISTANCE INCHES MS SERVICE RATING AIRSPACE CREEPAGE I A D E B C 1/32 1/16 1/8 3/16 1/4 5/16 1/16 1/8 3/16 1/4 5/16 1 DC V AC (RMS) MINIMUM FLASHOVER VOLTAGE AC (RMS) 250 700 1,250 1,750 2,450 4,200 1,000 500 900 1,250 1,750 3,000 1,400 2,800 3,600 4,500 5,700 8,500 PRESSURE ALTITUDE 70,000 FEET PRESSURE ALTITUDE 50,000 FEET STANDARD SEA LEVEL CONDITIONS OPERATING VOLTAGE MINIMUM MINIMUM FLASHOVER TEST FLASHOVER TEST VOLTAGE VOLTAGE VOLTAGE VOLTAGE AC (RMS) AC (RMS) AC (RMS) AC (RMS) 1,000 2,000 2,800 3,500 4,500 7,000 550 800 900 1,000 1,100 1,300 400 600 675 750 825 975 325 450 500 550 600 700 TEST VOLTAGE AC (RMS) 260 360 400 440 480 560 Not corrected for changes in density due to variations in temperature * No attempt has been made to recommend operating voltages. The designer must determine his own operating voltage by the application of a safety factor to the above derating chart to compensate for circuit transients, surges, etc. Wire Range Sizes Contact Resistance per MIL-DTL-5015 p3.5.4 26 AWG to 0 AWG (See contact selection on pages 70-73 CONTACT SIZE CONTACT RESISTANCE MILLIOHM MAX. POTENTIAL VOLTAGE DROP IN MILLIVOLTS MAX. 16/16S 12 8 4 0 6 3 1/(0.44)* 0.5/(0.23)* 0.2/(0.18)* 21 20 12 (20)* 10 (18)* 10 (27)* *Using Radsok contact Insulation Resistance @77F (25C) > 5,000 Megohms MECHANICAL Operating Temperature -67 to +257F (-55 to +125C) Neoprene Sealing 33 feet submersible when mated. IP 67 and NEMA 4P Amphenol(R) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com 45 Specifications subject to change. Technical Specifications Wire Sealing Range AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series The connector is designed for individual wire sealing. Sealing of an outer cable jacket on multiconductor cables must be accomplished with an appropriate endbell. Sealing is only guaranteed if wires according to MIL-W-5086 or within the listed ranges are used. SEALING RANGE CONTACT SIZE INCHES 16 12 8 4 0 - .118 .177 .256 .366 .539 2.3 3.2 3.8 7.1 10.0 - 3.0 4.5 6.5 9.3 13.7 Insulation Strip Lengths See Contact Selection Chart on page 70 Mating Life 2,000 cycles minimum (commercial) 500 cycles minimum (military) Salt Spray Olive drab chromate over cadmium - 500 hours Non-conductive black zinc - 200 hours Conductive black zinc - 48 hours Black anodized - 500+ hours Electroless nickel - 48 hours Heat Neoprene 257F (+125C); Low Smoke Zero Halogen (LSZH) 347F (+175C); Viton 392F (+200C) Chemical Resistance Diesel Fuel JP-4 Hydraulic Fluid Gasoline Corrosion Resistance Olive Drab Cadmium Plated 48 Hrs per MIL-DTL-5015 (3.17/4.6.13) Fluid Immersion Hydraulic Fluid 20 hours per MIL-DTL-5015 (3.19/4.6.15) Lubrication Oil 20 hours per MIL-DTL-5015 (3.19/4.6.15) per MIL-STD-810C, method 516.2, procedure VIII 1.0 g peak from 5 to 25 Hz .030" double amplitude from 25 to 57 Hz 5g peak from 57 to 500 Hz Vibration .090 .126 .150 .279 .394 (mm) 48-hour intermittent spray for each chemical with no deterioration, followed by Contact Retention (CR), Insulation Resistance (IR), Dielectric Withstanding Voltage tests (DWV) Basic Shock Per MIL-STD-810C, method 516.2, procedure I pulse at half sine wave of 30g for 11 seconds Gun fire Shock Per MIL-STD-810C, method 516.2, procedure IV pulse at half sine wave of 100g for 1.5 seconds Ballistic Shock Per MIL-STD-810C, method 516.2, procedure IV pulse at half sine wave of 200g for .5 seconds Contact Type Solder, Crimp, PC, Coax, or Thermocouple. Hard silver or gold plating. Contact Insertion From rear with simple hand tool. Removable, 5 cycles minimum. Contact Retention CONTACT SIZE 16 12 8 4 0 RETENTION FORCE MIN. 10 15 20 20 25 Pin and socket contacts are designed to resist severe vibration and repeated connection & disconnection. Contact retention and separation is tested according to MIL-DTL-5015 (3.10/4.6.6.3) Amphenol(R) 46 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Technical Specifications 1 to 85 Polarization Key and keyway plus three point bayonet with optional rotational polarization. See pages 59-69. Rear Accessories Maximum Torque Approvals/Agency Listing SIZE IN./LB. MAX. 10SL 14S 16 16S 18 20 22 24 28 32 36 40 26 44 50 50 55 65 85 90 114 120 153 170 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Number of Circuits THERMOCOUPLE CODES MATERIAL COLOR CODE CODE Iron Constantan Copper Alloy Chromel Alumel Black Yellow - White Green IR CON Cu CH AL Color code is identified by small dot on wire well end of contact. Thermocouple Types: J = Iron-Constantan K = Alumel-Chromel T = Copper-Constantan E = Chromel-Constantan UL File# E115497 AIB/GT Series Cross-Section receptacle shell skid washer bayonet coupling nut bayonet ramp sealing ring wave spring ferrule (sleeve) socket contact pin contact individual wire sealing grommet endbell insulator for socket contact AIB/GT Series How to Order bayonet pin stainless steel stud (optional) insulator for pin contacts endbell o-ring plug shell The next page contains a pictograph which portrays all of the standard possibilities for AIB/GT Series connectors. Follow the nine steps to create a description of the connector best suited to your application. This is not an Amphenol part number, but does give you a convenient way to select your connector. Call us with the description for a valid Amphenol part number. If you prefer to select the Amphenol part number, see the How-To-Order Guide on pages 94-95. Many options not shown are available. Call us if your needs are not met by the options on the next page. Amphenol(R) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com 47 Specifications subject to change. Follow these 9 steps to create your part number. . . AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series STEP 1 STEP 2 Select Connector Type Select Shell Style, Plug or Receptacle Plugs Receptacles AIB 0 Front Wall Mount with Accessory Threads Standard (Most Popular) Rear Wall Mount 6 mates with with Accessory Threads (Most Popular) 30 Cable Mount Rubber Covered 4 with Accessory Threads 1 mates with Front Box Mount with Rear Accessory Threads 20 AIBC Rear Mount Jam Nut Heavy Duty 6HD with Accessory Threads 70 mates with Front Box Mount No Accessory Threads 2 * AIBC is the commercial version of the AIB. It comes without wear pins in the receptacles and without wave springs in the coupling nuts. Rear Mount Jam Nut Box Mount ** Note: AIBC are fully intermateable with all reverse bayonet connectors. mates with 6B No Accessory Threads 7 Thru Bulkhead TB Create your part number using these nine steps (example) 48 AIB 6HD F A 24-28 4 5 1 2 3 Connector Type Shell Style Endbells * See pages 94-95 for Amphenol order codes. Layout Cable Clamp/ Heat if omitting Shrink endbell, enter - (dash) Boot (if needed) P W 6 7 Contact Rotation For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com S - 472 8 9 Plating/ Contact Type Modification Specifications subject to change. STEP 4 Choose Endbells STEP 5 Choose Cable Clamps and/or Heat Shrink Boot Choose layout STEP 6 See pages 50-69. (if applicable) RV G Choose Contact P = Pin S = Socket PS = Style TB only No Clamp Heat Shrink Boot STEP 7 Call with cable outside diameter. Heat Shrink AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series STEP 3 See pages 258-260. Choose Rotation See pages 59-69. (omit for normal) L C W X Y Z Long Extender MS-3057-C F Standard Extender STEP 8 A Choose Contact Type S = C= H= 0= T 90 MS-3057-A 9767 9767 P Call with cable outside diameter. Potting * Potting Compound see page 261 Solder Crimp* PC** Less contacts * When using a "C" in part number, the connector is supplied with the standard size crimp contacts for its layout. Bolded part number on pages 70-73 indicate crimp contacts. If reduced or enlarged crimp contacts are required, specify contact type 0 (less contacts) and order contacts separately. STEP 9 ** See page 75 and lengths. Standard Specials Call with NPT thread size, Sealtite conduit diameter, or cable outside diameter. Choose Platings/Modifications Shielded Cable/Heat Shrink Low Cost Gland Seal for post diameters CONTACTS Internal thread version Omit for silver contacts Shielded Cable Banding - B30 = Gold 30" Gold over Nickel - T = Thermocouple - RDS = RADSOK (Socket only) 8,4,0 SHELLS External thread version Gland Seal - 023 = Nickel (RoHS with crimp only) - 024 = Green Zinc Cobalt - 025 = Black Zinc Cobalt (RoHS with crimp only) Conduit Metal - 027 = Conductive Black Zinc Cobalt (RoHS with crimp only) - G96= Black Anodized Omit for olive drab chromate over cadmium Conduit Plastic See pages 262-263. Mesh Grip - 116 = Less Pre-tinned Solder Cups - 472 = 116 & 025 mod codes (RoHS) - 548 = 116 & 023 mod codes (RoHS) MATERIALS L = Low Smoke Zero Halogen V = High Temperature Viton(R)* *Viton is a registered trademark of DuPont Dow Elastomers For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 49 Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 97 (=97) AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 1 CONTACT LAYOUT 8S-1 10S-2 12S-4 12-5 14S-4 14-3 16S-3 16-2 # OF CONTACTS SERIES 1-#16 1-#16 1-#16 1-#12 1-#16 1#8 1#16 1-#12 SERVICE RATING A A D D D A B E LAYOUT # OF CONTACTS SERIES SERVICE RATING 16-12 18-6 18-7 18-16 18-420 20-2 22-7 24-52 1-#4 1-#4 1-#8 1-#12 1-#12 1-#0 1-#0 1-#12 A D B C 17 KVac 24 KVdc D E 21 KVac 30 KVdc 2 CONTACTS A A B A LAYOUT # OF CONTACTS SERIES SERVICE RATING B B B A A B A B B B A B A A 10SL-4* 12S-3* 14S-9* 16S-4 16-11 16-13 18-3 18-14 20-12 2-#16 2-#16 2-#16 2-#16 2-#12 2*-#12 2-#12 1-#16; 1-#4 1-#16; 1-#4 A A A D A A D A A A B A B B B B A A A A A B LAYOUT # OF CONTACTS SERIES SERVICE RATING B 20-23 22-1 22-8 22-11 24-9 28-7 2-#8 2-#8 2-#12 2-#16 2-#4 2-#4 32-5 2-#0 A D E B A D D 3 CONTACTS A A 100 C B C A A A C A C A B C LAYOUT # OF CONTACTS SERIES SERVICE RATING A C B A C C B C B B B 10SL-3 14S-1 14S-7 14S-12 16S-5 16S-6 16-7 16-10 18-5 3-#16 3-#16 3-#16 3-#16 3-#16 3-#16 2-#16; 1-#8 3-#12 1-#16; 2-#12 A A A A A A A A D A A A A A C A C LAYOUT SERVICE RATING A A C B B C B C B C C B B B B # OF CONTACTS SERIES B B C 18-22 20-3 20-6 20-19 20-51 20-59 22-2 22-6 3-#16 3-#12 3-#16 3-#8 3*-#8 3*-8 for #10 or 12 wire 3-#8 1-#16; 2-#8 D D D A A A D D 50 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 97 (=97) AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 3 CONTACTS (CONT.) A A A A A A A C C C B B C C B B C B C B B LAYOUT 22-9 22-21 22-80 28-3 28-6 28-72 # OF CONTACTS SERIES 3-#12 2-#16;1-#0 3*-#8 for #10 or 12 wire 3-#8 3*-#4 3-#4 (coax) RG-59A/U or RG-62A/U 36-4 3-#0 SERVICE RATING E A A E D (coax) D(A); A(B,C) 4 CONTACTS D A D 100 D D D A A C C C B D A B B C D D A A A A C C B B C B D B C B C B LAYOUT A 12SL-844 14S-2* 14S-10 16-9 16-59 18-4* 18-10* 18-13 18-15 # OF CONTACTS SERIES 4-#16 4-#16 4-#16 2-#16; 2-#12 4-#12 4-#16 4-#12 3-#12; 1-#8 4**-#12 SERVICE RATING I I I A A D A A A A D A D A D A C B D A C B D A C B A D A C B C D C B B LAYOUT 20-4* SERVICE RATING B C B # OF CONTACTS 4-#12 SERIES D C 20-20 20-24 22-4 22-10 22-22* 24-22* 3-#12; 1-#4 2-#16; 2-#8 2-#12; 2-#8 4-#16 4-#8 4-#8 4-#4 A A A E A D D D D D A C B A A A D LAYOUT A D B B D B C C # OF CONTACTS 32-17 C B C 32-58 36-5 36-51 36-64 36-65 4-#4 (coax) RG-161/U or RG-179/U 4-#0 2-#4; 2-#0 4-#0 (coax) RG-11/U; RG-12/U or RG-13/U 4-#0 (coax) RG-59/U; RG-62/U or RG-71/U SERIES SERVICE RATING COAX A D (coax) (coax) 1 1 4 2 5 CONTACTS 1 4 2 4 2 E A E 3 B 3 3 D D A D A E B C B A C E B C D C 40-57 40-66 40-86 14S-5* 16S-8* 18-11* 18-20 # OF CONTACTS LAYOUT 4-#0 4-#0 (coax) RG-63B/U 4-#0 (coax) RG-115A/U 5-#16 5-#16 5-#12 5-#16 SERIES E (coax) (coax) I A A A SERVICE RATING E A 110 A A A A E B E B B A D A C A B E D E C D B E C D LAYOUT # OF CONTACTS SERIES SERVICE RATING E D B B C C D 260 C D B E D C C 18-29 18-30 18-31 20-14 22-12 22-13 22-34 24-12 5-#16 5-#16 5-#16 3-#12; 2-#8 3-#16; 2-#8 1-#16; 4-#12 2-#16; 3-#12 3-#12; 2-#4 A A A A D D(E) A(A,B,C,D) D A For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 51 Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 97 (=97) AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 5 CONTACTS (CONT.) D A E D C E E A E D B E A D E A D B B B D C C A D C LAYOUT E B B D B A A E A C C B C C 24-17 24-51 24-53 24-79 28-5 32-1 32-2 32-79 # OF CONTACTS SERIES 3-#16; 2-#12 5-#8 5-#8 5-#8 2-#16; 1-#12; 2-#4 3-#12; 2-#0 2-#16; 3-#4 1-#8; 4-#4 SERVICE RATING D B; E for AWG #10 or 12 wire A; C; D for AN #18 wire A A D E(A); D(B, C, D, E) E D 6 CONTACTS 5 CONTACTS A 1 5 4 N 2 B E C F E E C G B E D A D F D B C D C A E F D A F 3 B F A B E A D B A F C B C C LAYOUT 40-5 40-75 14S-6* 18-12 20-8 20-17 20-22 # OF CONTACTS 5-#0 4-#0; 1-#12 6-#16 6-#16 4-#16; 2-#8 1-#16; 5-#12 3-#16; 3-#8 20-66 1-#16 5-#12 for #10 wire SERIES A E I A I A A A SERVICE RATING A A F F C A A F A F E F F B 1 A 2 3 E C B E C 4 E LAYOUT B B B B D E C E D 5 D C D D C D 6 22-5 22-15 22-24 28-22 28-82 36-3 36-6 # OF CONTACTS 4-#16; 2-#12 1-#16; 5-#12 4-#16; 2-#12 3-#16; 3-#4 4-#12; 2-#8 3-#12; 3-#0 4-#0; 2-#0 SERIES D A(A, B, C, E, F); E(D) D(C, D, E) A(A, B, F) D D D A SERVICE RATING 7 CONTACTS 1 6 2 5 4 100 3 F A G G F C E F A B D E G A E B G B G G C F A C E B B D F F C E E B D A D A D C C D LAYOUT # OF CONTACTS 40-74 14SA7 16S-1* 18-9 18-17 20-15* 20-57 4-#0 (coax) RG-9B/U or RG-214/U 1-#4 (coax) RG-62/U; 1-#12 7-#16 7-#16 5-#16; 2-#12 5-#16; 2-#12 7-#12 12 for #14 or 16 wire A A A I I A A SERIES SERVICE RATING F G LAYOUT # OF CONTACTS SERIES SERVICE RATING C A A F E A G E G B F F E C D A B F G B B B B E G F A G E B C D F A D A E D D C E C C G C D D 22-28 22-33 24-2 24-3 24-10 24-16 7-#12 7-#16 7-#12 5-#16; 2-#12 7-#8 3-#16; 3-#12; 1-#8 24-27 7-#16 A D(A, B, C, D) A(E, F, G) D D A D(A, B, F, G) A(C, D, E) E 52 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 97 (=97) AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 7 CONTACTS (CONT.) A F F F A G E A F B G E F A G E B F B E G E B F G B E B C D C D C D LAYOUT C C D # OF CONTACTS D C 24-60 24-66 24-71 24-75 28-10 32-10 36-73 7-#8 or 12 wire 7-#12 5-#8 for #10 or 12 wire, 2-#8 2-#8 for #16 wire; 5-#8 3-#12; 2-#8; 2-#4 3-#16; 2-#8; 2-#4 7-#4 (coax) RG-62B/U I D A A D(G); A(balance) E(A, F); B(G); D(B, E); A(C, D) (coax) SERIES SERVICE RATING 7 CONTACTS (CONT.) 8 CONTACTS 6 1 A A F F B B 5 7 2 A E E C C G G G F D D LAYOUT SERVICE RATING 4 B B F E 36-77 36-83 40-87 18-8* 20-7* 20-9 20-79 7-#4 7-#4 (coax) RG-58/U 7-#4 7-#16; 1-#12 8-#16 7-#16; 1-#12 7-#16; 1-#12 D (coax) D A D(A, B, H, G); A(C, D, E, F) H = (D); A(balance) H = D; A(balance) G A H A H 90 A D B H E C A B C D C D E E H F H F H C D D A B E F E C D F C B B E C SERVICE RATING A F H B E G G G F LAYOUT C D E D D A # OF CONTACTS SERIES B H F C E D G B H C C B F G H F H 3 A A G A E # OF CONTACTS SERIES C G D D B A A G E A G D G G 22-18 22-23 22-65 24-6 32-15 32-52 32-57 8-#16 8-#12 12 for #14 or 16 wire 8-#12 6-#12; 2-#0 2-#0; 6-#12 2-#0 (coax) RG-7/U; 6-#12 D(H); A(balance) D(A, G, H); A(balance) D D (coax) D(A, B, F, G, H); A(C, D, E) D(H); A(balance) 9 CONTACTS F E D A G A H G H I H A F I E A C LAYOUT 20-16 # OF CONTACTS 7-#16; 2-#12 SERIES SERVICE RATING A H C F B H B C J G H A F J B E D C A H B J G C J E D F C E D B G G G C F B I B D D F D E E 20-18* 20-21 22-16 22-17 22-20 22-27 6-#16; 3-#12 8-#16; 1-#12 6-#16; 3-#12 8-#16; 1-#12 9-#16 8-#16; 1-#8 A A A D(A); A(balance) A D(J); A(balance) A B A H A B A C G D E G J C F S A G E C P H B A G F B C I F E D D E F E H G 1 8 F 9 7 6 2 J H G E D D C C A D F I H LAYOUT B B J 3 5 4 24-11 28-1 28-4 28-84 28AY 32-3 32-75 # OF CONTACTS 6-#12; 3-#8 6-#12; 3-#8 7-#16; 2-#12 9-#8 5-#16; 4-#4 4-#16; 2-#12; 2-#4; 1-#0 7-#8 (coax); RG-180B/U 2-#12 SERIES A D(A, J, E); A(balance) E(G, P, S); D(balance) A A D D(8,9) (coax) SERVICE RATING 53 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 97 (=97) AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 10 CONTACTS A A H A G B I F 250 J F C E H C B 18-1* J E C K F D D J G H E F K # OF CONTACTS 10-#16 SERIES G A L C E J D C M K E D B B L B K H I C G J F LAYOUT E D A G B H J H A 18-19 18-24 20-58 24-21 28-19 10-#16 10-#16 5-#16; 5-#12 9-#16; 1-#8 6-#16; 4-#12 A A(B, C, F, G); I(balance) A D B(H, M); D(A, B) A(balance) SERVICE RATING A (B, C, F, G) I(balance) 11 CONTACTS A B A B A B A J B I B H M J C P K C K C D F L N H C L G F F D H E C J F E D H J M D E C J H D E D F E Q B G L H A J A K L K E F L K M L K M M LAYOUT 20-33 24-20 36-14 40-67 40-72 40-80 # OF CONTACTS SERIES 11-#16 9-#16; 2-#12 6-#16; 5-#12; 5-#8 10-#4 (coax); 1-#16 RG-59/U 10-#4 (coax); 1-#16 RG-9B/U 10-#4; 1-#16 SERVICE RATING A D D A (coax) A (coax) A 12 CONTACTS H C L F LAYOUT 22-63 L C J M E H E D D 28-9 28-18 6-#16; 6-#12 12-#16 12-#12 A E(L,M,); D(B) A(balance) D C(M); D(G, H, I, K, L) A(A, B); I(balance) A G N D E A H B L B F M G N D J A K E G N H J D 250 A B P F J L C N E G E H D F B M J C K R M H L A F C M A C D L L P J K H N J B N B K A I D M M P A J K F L K J N H H H P A K F F E 28-51 14 CONTACTS C M C M K D 28-8 L 100 C C E 10-#16; 2-#12 13 CONTACTS L F F G 12-#16 A B L D 24-19 # OF CONTACTS 8-#16; 4-#12 SERIES SERVICE RATING F C F H B K N M E E J H A H C L K E J J B M K F D M N K A K B B C L D K G J M L A G B M A J H A A N B E G B D N E E F C D LAYOUT 20-11 20-25 20-30 22-70 24-58 20-27* 22-19* 24-59 # OF CONTACTS SERIES 13-#16 13-#16 13-#16 5-#16; 8-#12 7-#16; 3-#12; 3-#8 14-#16 14-#16 7-#16; 7-#12 SERVICE RATING I I I A A A A A 14 CONTACTS 15 CONTACTS 10 1 A F K A K J P H J A L A B M G N C K C F LAYOUT # OF CONTACTS SERIES SERVICE RATING D E 28-2 C C F E 28-20 A D E F G M H H D E N J I J L M 13 7 4 J 5 R F H B C D J K E L A G E D H F J G K F N S H 6 A K M K N B L 3 12 O L M G 12-#16; 2-#12 4-#16; 10-#12 D 14 P H D N G C 8 B 2 11 B L B B 9 A R C P M L M N P N D O P E 32-4 32-9 36-78 24-65 28-17* 32-12 12-#16; 2-#12 12-#16; 2-#4 12-#8; 2-#16 4-#16; 11-#12 15-#16 10-#16; 5-#12 A(F, J, K, N); D(balance) D A A B(R); D(M, N, P); A(A-L) A(C, D, E, F, G); D(balance) 54 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 97 (=97) A R P A B C D F A J K N N J D B I O R H S L E M T L C K C D K E J B R P D C L E C D K E J F D G H K L M J N F S J H H K B A N B R P A T F G M T B R P L E M N P D S C M P H M L B L K E G M T A N A N C S H F F S P E H R Q F J LAYOUT 24-5 24-7* 28-66 28-74 28-75 28-79 32-68 # OF CONTACTS 16-#16 14-#16; 2-#12 14-#12; 2-#8 3-#8 for #10 wire; 4-#8; 9-#16 7-#8 for #10 wire 9-#16 7-#8; 9-#16 4-#4 (coax) RG-58C/U 12-#16 A A A A A A (coax) SERIES SERVICE RATING A AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 16 CONTACTS 16 CONTACTS 17 CONTACTS A J A P B B D C F G P K L L M P G K E R Q LAYOUT P R S P S R R K T S A U J A T B C B D D Q H E E J G G H F F H N C N J F # OF CONTACTS SERIES SERVICE RATING B M D L J N A N H M L Q M L C K E H N M I F C D E K 32-82 36-14 20-29* 28-59 36-13 12-#16; 4-#4 6-#16; 5-#12; 5-#8 17-#16 10-#16; 7-#12 15-#16; 2-#12 A D A A E(N, P, Q) A(balance) 19 CONTACTS 1 90 E J F M L K B N V H S R G C P H D P V N T E U C G B H A J V N T U 7 10 11 13 A 14 15 17 LAYOUT 22-14* 24-67 24-84 32-76 19-#16 19-#12 18-#12; 1-#12 (coax) RG-188/U or RG-174/U 19-#12 A I A (coax) A SERIES 21 CONTACTS 20 CONTACTS 2 3 P M 4 2 5 3 4 5 K A T L 6 B M 7 H U V R Q 10 6 7 8 11 12 13 10 15 K 12 13 14 15 D C V 17 18 16 19 17 18 P V R W 19 B E F C L S F A G B H C I J K O L H M P R S U V W N T D M F T I G 20 G E K X H 20 U E T U D P J N D S J E F 9 14 N 16 G 9 A R X C 11 S 8 B W L J 22 CONTACTS A N 1 1 16 19 18 # OF CONTACTS SERVICE RATING 12 B L L F 9 C M K M K P 3 6 5 8 S 2 4 90 R S J D G E F R A U T D LAYOUT 28-16 36-79 36-80 40-68 28-11* 36-1 # OF CONTACTS SERIES 20-#16 20-#12 20-#12 for #10 wire 21-#8 18-#16; 4-#12 18-#16, 4-#12 SERVICE RATING A A A A A D 23 CONTACTS A B C E D G H L M I A E B F K C D G H P N M F J O K R L M S N T P V T X T H M J F F S H F B T N U V V X W D K C X W M D G H L M I K U Y E B C J T a G Z Z E A S P N R D E U A H D G L I P R O V V W W X K Z J U B C E C S S Q U R Y W K J 100 B P X L N R A A P F J N R O S T U V W X L LAYOUT 24-80 32-6 32-13 32-16 32-60 32-62 # OF CONTACTS 23-#16 16-#16; 2-#12; 3-#8; 2-#4 18-#16; 5-#12 16-#16; 2-#12; 3-#8; 2-#4 8-#8 (coax); 15-#16 RG-124/U 2-#8 (coax); 16-#16; 2-#12; 1-#8; 2-#4 RG-124/U I A D A A (coax) A (coax) SERIES SERVICE RATING For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 55 Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 25 CONTACTS AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 24 CONTACTS 26 CONTACTS 13 1 2 12 11 A B E C F K G L S B T P Q K W X Y L M R S W Z H U X Z Y 8 V W X K D V K F W X H LAYOUT 24-28* 24-AJ 32-25 28-12* 24-#16 25-#16 25-#12 26-#16 SERVICE RATING I A A A A 29 CONTACTS 28 CONTACTS 14 M H K G T 12 N 2 a 4 25 18 22 27 11 26 21 10 9 R e A J P W R c B K J P a N G L P U C R V Y W Z L S X K O T G b L J X a c b d e a LAYOUT 24-96 40-10 32-8 32-56 40-1 # OF CONTACTS SERIES 28-#16 16-#16; 9-#8; 4-#4 24-#16; 6-#12 6-#12 for #10 wire; 24-#16 24-#16; 6-#12 SERVICE RATING I A A A D 34 CONTACTS 31 CONTACTS S 1 16 18 14 26 19 31 24 f 10 T T V W b a h N U Z e d M T Y c j f g F G N G L S X C L 8 F K R B R X c E J P K W b G B D H A H f L 9 E J V Y e F R X C D P C K W b 6 c B A I O d H Y 7 22 a A P e 20 21 29 23 11 E J V M U Z D 5 28 30 12 100 I O d 4 27 25 13 a 3 17 S M U Z 2 15 k m N LAYOUT 32-31 36-9 36-18 36-20 # OF CONTACTS SERIES 31-#16 14-#16; 14-#12; 2-#8; 1-#4 14-#16; 14-#12; 2-#8; 1-#4 30-#16; 2-#12; 2-#8 SERVICE RATING A A A A S B K R e F I M F W C A E V d G S X I O Z H D N U F b X b Z 7 U T W c Y 6 8 S V 5 19 20 C E H Y E O V d O 3 I Z Q D N U c P M 17 28 B D M T H Y L 1 24 23 13 30 CONTACTS E D J I 16 26-#16 A C 15 28-13 A B F F G J H # OF CONTACTS SERIES E L G J C U d Y E B T b Z M L 6 7 d Y 5 a U A S a N C D 4 18 R P B T b Z M 9 V N 100 A S a 15 16 17 20 Q R P 24 25 10 P 3 14 22 21 J N T 23 19 D G F E V U C A J N M R D H 97 (=97) 35 CONTACTS S A B C D E F G J K L H M P R X S Z Y V U T Z h g Z Y j b E D W M X a F X L E g h F G Y Z G K H K O V f m H J J LAYOUT 28-15* 32-7* 36-15 36-85 # OF CONTACTS SERIES 35-#16 28-#16; 7-#12 35-#16 35-#16 for #12 wire SERVICE RATING A I(A, B, h, j); A(balance) D(M); A(balance) D(M); A(balance) 36 CONTACTS 37 CONTACTS 38 CONTACTS 35 CONTACTS 16 P 1 15 3 27 g 8 k b K 22 23 E D K m 6 9 V q c 21 24 B W X a 7 S E Z Y M L T U h n N e d k j p Z X 11 5 33 4 16 f m s H 32 15 26 13 14 27 30 29 28 LAYOUT 40-35 40-64 28-21* 40-AG # OF CONTACTS 35-#12 13-#8 (coax) RG-124/U 20-#16; 3-#12 37-#16 38-#12 SERIES SERVICE RATING D I (coax) A A For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com 25 12 31 r 24 17 R P 23 3 1 34 J W V c b a H 2 6 D G F g F J C A j 5 31 25 11 22 10 7 35 C U n d L 20 21 9 18 T i p f 20 8 19 36 S 30 35 32 M 4 19 33 10 37 B R h 26 12 38 A 2 18 29 34 13 N 17 28 14 56 f C e k D W L B U c N a M D V e b N U I m l N V m j B C H b k k A G M T a g h f j L A T d C P c P F f k g e d K S Y e j W c b a d h N Q U d Q E S R B T J R X A R P W c Specifications subject to change. Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 42 CONTACTS b a A W r C n F W H V m s k r E d t j q f p g i U T n K LAYOUT P F H H F k X q r U f n g 59 62 A B K 66 70 73 77 80 65 69 72 74 75 78 79 81 82 83 84 u t v E D C 61 64 68 71 57 60 63 67 V p s 52 54 56 58 m h 51 53 55 T d i 49 50 S c 85 w 86 87 91 L R P 88 M N 89 90 36-54 36-55 32-53 36-74 8-#8 for #6 wire; 31-#16 37-#16; 5-#12 8-#1 (coax); RG187/U 43-#16 A A E(T, U) I(balance) A (coax) SERIES 46 CONTACTS 47 CONTACTS A 21 20 19 18 16 b j 31-#16; 8-#8 SERVICE RATING 17 R Y 76 J h S M N p g T L R q f i U J h S # OF CONTACTS j 48 P a Z J W V N M L D K X E d t B c Y D m s k A Z C c X b a B Z 44 CONTACTS 35 23 44 34 H 3 4 24 38 45 43 33 39 46 15 42 32 14 27 41 31 12 11 d j t u Y T b f U p g m s R N X f g t j u k p m v w r y c b e n T S W a Z h w z J V d r t u Y E G M L P U e j p v x y O I K a Z h k n R V d c s x P D F H L O B C 100 H K M X m v w 8 W g k F J A C E D I S c b f 7 N T X a e 9 10 N W r 28 29 30 13 G S V n 40 B M R Z h 6 26 L P U Y 5 25 I K O A E J G F 2 37 B D C 1 22 36 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 39 CONTACTS Y 97 (=97) s y x z z LAYOUT 32-73 36-7* 36-8 36-16 # OF CONTACTS SERIES 46-#16 40-#16; 7-#12 46-#16; 1-#12 40-#16; 7-#12 SERVICE RATING A A A A A B C A B D C F O M L P Z d h T c b f g t u k Y Z h d j p v w m r N b 22 g t 11 24 32 36 17 25 33 26 E I J O K P Q R U V W S Y Z b c d g h X 34 e f l m p q t u 35 39 j 42 46 L T a n r 47 z i o k 44 45 y N 30 38 41 43 F D H 21 29 37 40 12 16 20 28 s M 8 15 23 31 p v 10 19 27 m k w G 5 7 14 18 c f x 13 X a u 9 T S W e r y 6 M R z LAYOUT 4 J V n s x L P U 2 3 G I K O X a e j n W 1 E F H N S R V U Y J I B D C 110 G H K A E s 36-17 36-60 36-76 40-9 # OF CONTACTS SERIES 40-#16; 7-#12 7-#12 for #10 wire; 40-#16 47-#16 24-#16; 22-#12; 1-#8 SERVICE RATING A A A A 48 CONTACTS A C H O V P W d Q e R f Z g u LAYOUT SERVICE RATING a q z k s x O c b r w v U j C H N T h p 100 G M S y # OF CONTACTS SERIES A F L Y n t E K X m B D J V P W d R Y f S T h w v H U b s x O c k j r q C N a g u G M Z p n t L Q e A F E K X m B D J V P W d B D E J K Q X e m Z g a u v w 29 28 U c b j r q 31 N T h p 110 G M S Y n t R f 1 F L k s x 27 33 30 26 25 24 36 22 46 45 21 39 z y 13 44 15 20 18 w 8 11 12 N g 17 z W L 14 16 X M u f B R Y v e A P O 10 43 19 y 9 Q x 7 38 42 y 5 6 40 d z 4 37 35 41 23 3 34 48 47 2 32 c Z b a U J s D T E j k F G H h S V K t C m n r q p 36-10* 36-11 36-12 36-75 36-AF 48-#16 48-#16 48-#16 48-#16 for #14 wire 48-#16 A A A A A 57 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Number of Contacts CONTACT LEGEND =16 =12 Mating face view of pin inserts =8 =4 SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) P-lok () Thermocouple () *most popular =0 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 52 CONTACTS A B D J B H G U K a Z r j k v AA z i 9 15 x V t AB AA N W c k w a r x j z AH AF AJ 32-414 36-52 36-403 36-59 36-71 # OF CONTACTS SERIES 52-#16 52-#16 52-#16 3-#12 for #10 wire; 50-#16 50-#16; 3-#12 SERVICE RATING A A A A A 55 CONTACTS 59 CONTACTS 1 3 8 A B D C G F P O T R e d h u t s y z AC N R V W Z AB AE a d h e S q u z b m y V 33 a f 26 34 50 k q 19 27 35 43 51 v x 6 13 20 28 36 AA 29 37 15 22 30 38 44 45 46 52 23 31 39 47 24 32 40 48 54 53 41 49 55 56 59 58 AE AF 14 21 AC AH AD AG 7 12 57 y z 5 11 r u t 18 42 e j p 10 W Z d AB 25 R U Y h w AE AF P T c n s AC AA AD J M O g v x w f r k j p t AG AF U Y n s AA AD c g m H L 17 2 4 9 16 E G X b r v x w AB k q D F K P T X f j p n S a Z Y c g J M O B C E H L N W A D G K V U X b m F M L N S C J H K B A E AG LAYOUT 32-22 32-64 32-AF 40-61 # OF CONTACTS SERIES 54-#16 54-#16 55-#16 55-#16; 3-#12; 1-8 SERVICE RATING A I A A 61 CONTACTS 60 CONTACTS 24 23 22 21 53 23 3 22 4 27 44 21 39 5 39 46 58 51 17 37 50 16 14 LAYOUT 34 13 17 28 56 59 57 29 58 36 33 51 17 37 16 12 13 14 48 49 34 13 37 29 9 6 47 58 8 21 37 46 31 47 10 12 15 23 39 53 9 14 30 32 48 49 50 56 60 40-70 # OF CONTACTS SERIES 60-#16 60-#16 60-#16 for #14 wire 61-#16 for #14 wire 61-#16 SERVICE RATING A A A A A 42 20 19 6 47 48 8 32 49 9 33 35 34 15 14 7 31 58 50 13 10 12 6 13 21 29 7 3 14 22 30 8 1 4 15 23 31 9 16 24 32 10 17 25 33 18 26 34 5 11 2 12 19 27 35 37 38 46 39 47 40 48 54 41 49 55 42 50 56 43 51 57 28 20 45 53 58 13 21 29 36 44 52 6 3 7 8 A 4 9 10 37 22 30 38 46 14 15 23 31 39 47 24 32 40 48 54 16 25 33 41 49 55 17 34 42 50 56 18 26 51 57 19 27 35 43 60 61 62 59 60 61 C H 52 58 X 28 D J K 53 AC L M AP 62 AS BA AT BB BK BL BS AL AW BE BN BU r AA AK BD BM BT z AV AU BC g q y AJ W f p x AH AF V d n w AE AR AZ m v U c b k u T a j AD S Z i t 45 R Y h 36 44 P BJ 59 B F 11 N 30 57 36 16 20 46 59 37 5 29 51 17 12 45 61 38 18 28 56 60 52 5 4 27 44 2 85 CONTACTS E 3 26 55 53 39 1 2 25 43 54 40 62 CONTACTS 1 24 23 44 52 61 40-63 41 51 11 40-85 22 27 35 43 57 40-62 21 18 26 34 42 40-53 61 CONTACTS 17 25 33 41 55 59 10 16 24 40 54 58 5 8 22 38 9 33 13 29 45 32 34 13 36 48 35 14 20 4 7 12 28 7 31 49 15 19 30 57 50 11 11 46 3 6 5 45 56 61 36 16 10 12 28 51 17 8 31 32 33 35 15 11 58 50 36 7 30 2 4 27 44 59 18 1 3 26 43 60 52 38 47 2 25 55 39 19 46 59 9 10 11 34 14 38 40 53 6 57 18 31 32 49 35 15 52 54 5 29 60 8 47 45 55 41 20 28 56 19 30 48 44 42 21 4 27 39 7 46 53 22 3 1 24 23 2 26 43 54 40 20 6 45 60 50 16 9 10 12 55 51 37 8 31 32 33 35 15 48 49 36 18 7 30 47 59 44 1 25 42 41 21 5 27 52 38 57 38 54 22 4 26 43 53 19 6 60 52 18 20 29 56 19 41 24 23 3 25 42 40 28 45 55 2 24 2 26 43 54 40 20 1 1 25 42 41 t AB AA AE AD AJ 54 CONTACTS k s y AC AF b i q U T Z h p v S g n u R Y f K J P X d m C D H F M AH AD 24 23 AF b s AE AC 22 L j z y 20 19 18 AC a r x E U T i q w AH AD h p v S Z g n u R Y f A B K J P X d m + N W c C D H F M V 14 17 16 21 3 C 10 13 12 11 E L 7 r w AB 6 8 h q p u Z Y A B A 4 5 S g n AE LAYOUT X f m t R W d 2 1 3 K J P V y w H N c s x 4 5 U 53 CONTACTS C D F M b p s y z 6 a rg h t u 2 T R Y f S j k v L b l m L E T c d n E F M V W e A N P Q X f C 97 (=97) BP AM AX BF s AB AN AY BH BR BV 11 LAYOUT 40-73 40-81 40-82 # OF CONTACTS SERIES 61-#16 62-#16 for #14 wire 62-#16 40-56 85-#16 SERVICE RATING A A A A 58 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size N W AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Mating Face view of pin inserts X Z Alternate Insert Position (Rotation) Y SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) SERIES LAYOUT 97 AIT 8S-1 AIB P-lok TOTAL 1 10S-2 DEGREES OF ROTATION CONTACTS SIZES 20 16 12 8 4 0 1 W X Y Z SERVICE RATING - - - - A 1 1 - - - - A 10SL-3 3 3 - - - - A 10SL-4 - - - - A 2 2 10SL-51 2 2 10SL-52 2 2 10SL-53 2 2 10SL-54 3 3 10SL-55 3 3 10SL-56 2 2 10SL-57 2 2 10SL-58 3 3 10SL-59 2 2 10SL-60 2 2 10SL-61 2 2 10SL-62 3 3 10SL-63 3 3 10SL-4 45 A=Ir.; B=Con. 10SL-4 45 A=Cu; B=Con. 10SL-4 45 A=Al.; B=Ch. 10SL-3 A=Ir.; B=Con.; C=Cu 10SL-3 A=Al.; B=Ch.; C=Cu 10SL-4 A=Al.; B=Ch. 10SL-4 A=Ch.; B=Con. 10SL-3 A=Ch.; B=Al.; C=Cu 10SL-4 A=Ch.; B=Al. 10SL-4 A=Ir.; B=Con. 10SL-4 A=Cu; B=Con. 10SL-3 A=Cu; B=Al.; C=Ir. 10SL-3 A, C=Con.; B=Ch. 3 3 12S-1 2 2 12S-3 100 12S-2 2 2 12S-3 250 12S-3 2 2 70 10SL-64 12S-4 1 1 12S-51 2 2 12S-54 2 2 12S-55 2 2 12S-56 2 2 12S-57 2 2 12S-58 2 2 12S-59 2 2 12S-60 2 2 12S-61 2 2 12S-62 2 2 4 4 12SL844 10SL-3 - A, C=Ch.; B=Al. A A 145 215 290 A - - - D 12S-3 315 A=Ch.; B=Al. 12S-3 315 A = Ir.; B=Con. 12S-3 45 A=Cu; B=Con. 12S-3 A=Al.; B=Ch. 12S-3 60 A=Ch.; B=Al. 12S-3 120 A=Ir.; B=Con. 12S-3 A=Ir.; B=Con. 12S-3 A=Cu; B=Con. 12S-3 A=Ch.; B=Con. 12S-3 A=Ch.; B=Al. - - - - I 12-5 1 - - - - D 14S-1 3 3 - - - - A 14S-2 4 4 - 120 240 - 14S-4 1 1 - - - 14S-5 5 5 - 110 - - 14S-6 6 6 90 - - - I 14S-7 3 3 90 180 270 - A 1 I D I 59 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size N AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series W Mating Face view of pin inserts X Z Alternate Insert Position (Rotation) Y SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) LAYOUT 97 AIT AIB DEGREES OF ROTATION CONTACTS SIZES SERIES P-lok TOTAL 20 16 12 8 4 0 W X Y Z SERVICE RATING 145 215 290 A 14S-9 2 2 70 14S-10 4 4 14S-2 100 I 14S-11 4 4 14S-2 250 I 14S-12 3 3 14S-1 100 14S-13 3 3 14S-1 260 A 14S-14 4 4 14S-2 100 I 14S-51 2 2 14S-9 90 A=Al.; B=Ch. 14S-52 4 4 14S-53 2 2 14S-54 6 6 14S-55 4 4 14S-56 4 4 14S-57 4 4 14S-58 3 3 14S-59 2 2 14S-60 2 2 14S-61 6 6 14S-63 6 6 14S-64 4 4 14S-65 6 6 14S-67 6 6 14S-68 4 4 14S-69 3 3 14S-70 4 4 14S-71 4 4 14S-72 2 2 14S-73 4 4 14S-74 4 4 14S-75 4 4 14S-76 4 4 14S-77 4 4 14S-78 2 2 14SA7 7 7 14-3 16S-1 1 16S-3 1 7 14S-2 45 A, B=Cu; C=Al.; D=Ch. 14S-9 90 A=Ir.; B=Con. 14S-6 45 A, C, E=Ir.; B, D, F=Con. 14S-2 45 A, C=Ir.; B, D=Con. 14S-2 45 A=Ir.; B=Con.; C, D=Cu 14S-2 45 A, C=Al.; B, D=Ch. 14S-7 45 A=Al.; B=Ch.; C=Cu 14S-9 90 A=Cu; B=Con. 14S-9 14S-6 A=Al.; B=Ch. A, C= Al.; B, D=Ch.; E=Ir.; F=Con. 14S-2 A, C=Con.; B, D=Cu 14S-6 A, C, E= Cu; B, D, F=Con. 14S-6 A=Al.; B=Ch.; Balance=Cu 14S-2 A 45 A=Al.; B=Ch.; C=Ir.; D=Con.; E, F=Cu 14S-6 45 A=Ch.; B=Con.; C, D=Cu 14S-7 A=Con.; B=Ch.; C=Cu 14S-2 A, D=Ch.; B, C=Al. 14S-2 A, B, D=Cu; C=Con. 14S-9 A=Con.; B=Cu 14S-2 A, B=Cu; C=Al.; D=Ch. 14S-2 A, B=Ch.; C, D=Al. 14S-2 A, B=Cu; C, D=Con. 14S-2 A, C=Al.; B, D=Ch. 14S-2 A, D=Al.; B, C=Ch. 14S-9 A=Ch.; B=Al. - - - - A - - - - A 80 - - 280 A 1 1 - - - - B 2 2 35 110 250 325 D 145 215 290 A 180 270 - A 16S-5 3 3 70 16S-6 3 3 90 16S-4 7 X & Z are valid. Call for details. 60 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) CONTACTS SIZES DEGREES OF ROTATION W X Y Z SERVICE RATING 5 - 170 265 - A 3 3 16S-4 110 A 2 2 16S-5 100 D 2 2 16S-4 250 D 3 3 16S-5 250 A 2 2 7 7 LAYOUT 97 AIT AIB P-lok TOTAL 16S-8 5 16S-14 16S-15 16S-16 16S-17 16S-52 16S-54 20 16 12 8 4 0 16S-4 A=Ch.; B= Al. 16S-1 A=Al.; B=C; Balance=Cu 7 7 16SA18 7 7 16S-1 100 A 16SA19 7 7 16S-1 260 A 16SA20 7 7 16S-1 110 A 16SA21 7 7 16S-1 250 1 16S-55 16-2 1 16-7 3 2 16-9 4 2 16-10 16-11 16-12 16-13 16-52 2 16-53 4 16-55 1 3 16-56 2 2 16-57 3 3 16-58 3 3 16-59 4 4 16-60 2 2 - - - E 110 250 280 A 35 110 250 325 A 3 3 90 180 270 - A 2 2 35 110 250 325 A 1 2 2 2 2 2 10 10 18-1 10 10 18-3 2 18-4 18-5 18-6 1 18-7 1 A 80 1 A=Con.; Balance=Cu 2 18A31 16-62 1 16S-1 2 2 4 3 1 - - - A 110 250 325 A=Ir.; B=Con. - A 16-11 90 A=Al.; B=Ch. 16-9 70 A=Al.; C=Ch.; B, D=Cu 16-10 45 A=Al.; B=Ch.; C=Cu 16-13 90 A=Con.; B=Cu 16-10 A=Al.; B=Cu; C=Ch. 16-10 A=Con.; B, C=Cu 2 1 1 - 16-13 - A=Al.; B=Ch. 16-11 18-1 2 4 35 - A=Con.; B=Cu 110 A(B,C,F,G) I(all others) 70 145 215 290 A(B,C,F,G) I(all others) 35 110 250 325 D 35 110 250 325 D 80 110 250 280 D - - - - D - - - - B 18-8 8 7 1 70 - - 290 A 18-9 7 5 2 80 110 250 280 I 18-10 4 4 - 120 240 - A 18-11 5 5 - 170 265 - A 18-12 80 - - 280 A 18-13 80 110 250 280 A 80 110 250 280 A 18-14 6 4 2 6 3 1 1 1 18-15 4 4 - 120 240 - A,C=Ir. B,D=Con. 18-16 1 1 - - - - C 18-17 7 5 2 18-9 100 18-18 2 18-9 250 18-19 18-20 18-22 18-23 I 7 5 10 10 80 120 240 5 5 90 180 270 - A 3 3 70 145 215 290 D 10 10 18-1 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series SERIES I 100 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com - A A(B,C,F,G) I(all others) Specifications subject to change. 61 Layouts by Shell Size N AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series W Mating Face view of pin inserts X Z Alternate Insert Position (Rotation) Y SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) SERIES P-lok TOTAL 97 AIT AIB 18-24 10 18-25 2 18-26 2 18-27 3 18-28 3 18-29 5 5 90 18-30 5 5 18-20 110 18-31 5 5 18-20 260 18-420 20 16 12 4 0 10 W X A(B,C,F,G) I(all others) 2 18-3 100 D 2 18-3 250 D 1 2 18-5 100 D 1 2 18-5 250 D 180 270 - A A A 24 KVdc, 17 KVac 6 18-52 5 18-53 6 18-54 4 18-56 10 10 18-57 6 6 18-59 6 6 18-60 5 18-61 6 6 18-62 6 6 18-63 4 18-65 6 6 18-66 10 10 18-67 6 6 18-68 5 18-69 10 18-70 5 5 18-71 4 4 18-72 4 18-73 7 6 5 6 4 5 4 5 10 4 5 6 6 20A16 13 13 20A37 4 SERVICE RATING Z 250 1 HV Y 18-1 18-51 20-2 8 LAYOUT 18-74 DEGREES OF ROTATION CONTACTS SIZES 2 4 1 1 18-12 A=Ir.; B, E=Con.; D=Cu; C, F=Dummy 18-11 A=Ir.; B=Con.; C=Ch.; D=Al.; E=Dummy 18-12 A, D=Ir.; B, E=Con.; C, F=Dummy 18-15 A, C=Al.; B, D=Ch. 18-1 45 A, C, E, G, I=Ir.; B, D, F, H, J=Con. 18-12 45 A, C, E=Al.; B, D, F=Ch. 18-12 45 A, C=Ir.; B, E, F=Con.; D=Cu 18-11 45 A, D=Al.; B, C,=Ch.; E=Cu 18-12 A, C=Ir.; B, D=Con.; E=Ch.; F=Al. 18-12 A, B, C=Ir.; D, E, F=Con. 18-15 A, C=Con.; B, D=Cu 18-12 A=Ir.; B=Con.; Balance=Cu 18-1 A, C, E, G, I=Cu; B, D, F, H, J=Con. 18-12 A, C, E=Cu; B, D, F=Con. 18-11 A, D=Al.; B, C=Ch.; E=Cu 18-1 A=Al.; B=Ch.; Balance=Cu 18-11 A=Ir.; B=Con.; C=Ch.; D=Al.; E=Cu 18-15 A=Con.; Balance=Cu 18-15 D=Con.; Balance=Cu 18-9 A=Al.; D=Ch.; Balance=Cu 18-12 A=Ch.; B=Al.; D=Ir.; E=Cu; C, F=Con. 20-11 182 I 20-4 250 D - - - - D 20-3 3 3 70 145 215 290 D 20-4 4 4 45 110 250 - D 20-6 3 3 70 145 215 290 D 20-7 8 8 80 110 250 280 A(B,C.F,G) I(all others) 6 4 80 110 250 280 I 13 13 - - - - I 20-8 20-11 2 62 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) LAYOUT 97 AIT AIB 20-14 20-15 20-16 9 20-17 20-18 20-19 3 20-20 20-21 20-22 DEGREES OF ROTATION CONTACTS SIZES P-lok TOTAL 20 W X Y Z SERVICE RATING 80 110 250 280 A 80 - - 280 A 2 80 110 250 280 A 1 5 90 180 270 - A 6 3 35 110 250 325 A 90 180 270 - A 80 110 250 280 A A 16 12 8 5 3 2 7 7 7 6 9 3 9 8 6 3 1 1 20-23 20-24 20-25 20-27 20-29 20-30 20-32 20-33 20-51 3 20-52 4 20-56 8 20-57 7 20-58 10 20-59 3 20-60 8 8 20-61 17 17 20-62 7 20-64 14 14 20-65 14 14 20-66 6 5 1 20-67 9 7 2 20-68 8 8 20-69 14 14 20-70 17 17 20-71 17 17 20-74 17 17 20-75 7 20-77 9 7 2 20-79 8 7 1 20-80 14 14 20-81 14 14 20-82 17 17 0 3 4 4 2 35 110 250 325 3 80 110 250 280 A 2 35 110 250 325 A 2 35 110 250 325 A 250 325 A - 280 A 4 2 13 13 20-11 14 14 35 17 17 80 13 13 20-11 250 8 8 20-7 260 11 11 - - - 280 A - - - - A 3 4 8 5 100 I 110 - I A(B,C,F,G) I(all others) 20-4 315 A=Ir.; B=Con.; C=Ch.; D=Al. 20-7 45 A, B, G, H=Ir.; C, D, E, F=Con. 7 - - - - A 5 - - - - A - - - - A 3 7 20-7 45 D=Ch.; E=Al.; Balance=Cu 20-29 45 A, B, M=Cu; Balance=Con. 20-15 80 A, C, E=Al.; B, D, F=Ch.; G=Cu 20-27 A=Al.; C=Ch.; Balance=Cu 20-27 A, B, C, D, E, F, G=Ir.; H, I, J, K, L, M, N=Con. - 7 - - - 20-16 H=Al.; I=Ch.; Balance=Cu 20-7 A, B, G, H=Con.; C, D, E, F=Cu A 20-27 A, B, C, D, E, F, G=Cu; H, I, J, K, L, M, N=Con. 20-29 A, C, E, G, J, L, N, R, T=Ir.; B, D, F, H, K, M, P, S=Con. 20-29 S=Al.; R=Ch.; Balance=Cu 20-29 A, C, E, G, J, L, N, R=Ir.; B, D, F, H, K, M, P, S=Con.;T=Cu 20-15 G=Al.; Balance=Ch. 20-16 A=Con.; Balance=Cu 20-27 - - - A/D A, C, E, G, I, K, M=Cu; B, D, F, H, J, L, N=Con. 20-27 A, C, E, G, I, K, M=Ch.; B, D, F, H, J, L, N=Al. 20-29 A, C, E, G, J, L,N, R=Al.; B, D, F, H, K,M, P, S=Ch.;T=Cu 22-1 2 2 35 110 250 325 D 22-2 3 3 70 145 215 290 D 22-4 2 35 110 250 325 A 22-5 35 110 250 325 D 22-6 80 110 250 280 D 22-7 - - - - 4 2 6 4 3 1 1 2 2 1 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series SERIES 22-8 2 2 35 110 250 325 E 22-9 3 3 70 145 215 290 E E = Reduced contact crimp pot 63 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size N AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series W Mating Face view of pin inserts X Z Alternate Insert Position (Rotation) Y SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) SERIES LAYOUT 97 AIT AIB 22-10 4 4 22-11 2 2 22-12 5 3 22-13 5 1 22-14 19 19 22-15 6 1 22-16 9 6 9 8 22-17 DEGREES OF ROTATION CONTACTS SIZES P-lok TOTAL 20 16 W X Y Z SERVICE RATING 35 110 250 325 E 35 110 250 325 B 80 110 250 280 A 35 110 250 325 A(A-D) D(E) 80 110 250 280 A 5 80 110 250 280 A(A-C, E, F) E(D) 3 80 110 250 280 A 1 80 110 250 280 D(A) A(all others) 80 110 250 280 A(C-E) D(all others) 12 8 4 0 2 4 22-18 8 8 22-19 14 14 80 110 250 280 A 22-20 9 9 35 110 250 325 A 3 2 80 110 250 280 A 22-22 4 - 110 250 - A 22-23 22-21 22-24 1 4 8 8 35 - 250 - D(H) A(all others) 4 2 80 110 250 280 D(C, D, E) A(A, B, F) 7 5 2 9 8 80 - 250 280 D(J) A(all others) - - 280 A 6 22-26 22-27 22-28 22-30 19 19 22-14 100 A 22-31 2 2 22-11 100 B 22-32 6 4 2 22-5 260 D 22-34 3 7 1 7 5 2 22-57 19 19 22-60 19 19 22-62 8 22-63 12 8 22-65 8 8 22-68 14 24 22-69 14 19 22-70 13 5 8 22-71 19 4 2 22-72 6 4 2 22-73 6 8 22-74 8 8 22-75 8 22-76 21 80 80 110 250 280 22-14 45 22-14 45 U=Al.; N=Ch.; Balance=Cu 22-23 60 A, B, F, G=Al.; C, D, E, H=Ch. D A, C, E, G, J, L, N, R=Ir.; B, D, F, H, K, M, P, S=Con.; T, U, V=Cu 22-77 14 22-78 19 8 4 - - - - A - - - - A/D 22-19 45 22-19 45 A, C, E, G, J, L, M=Cu; B, D, F, H, K, P, N=Con. - A, C, E, G, J, L, M=Ir.; B, D, F, H, K, P, N=Con. - - - 22-14 V=Al.; U=Ch.; Balance=Cu 22-5 B=Al.; E=Ch.; Balance=Cu 22-5 E=Al.; B=Ch.; Balance=Cu 22-23 A, C, E, G=Ir.; B, D, F, H=Con. 22-23 A A=Al.; B, D, G, H=Cu; C=Ch.; E=Ir.; F=Con. W=Con.; Balance=Cu 22-19 B, D, F, H, J, K, M, P=Cu; A, E, L=Ir.; C, G, N=Con. 22-14 A, C, E, G, H, K, M, P, R, T=Con.; Balance=Cu = Reduced contact crimp pot 64 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) LAYOUT 97 22-79 AIT AIB 4 3 16 22-80 24A35 24-2 24-3 P-lok TOTAL 20 16 12 14 7 7 5 W 16 22-10 D D 80 110 250 280 A 80 110 250 280 D(A,G,H) A(all others) 24-7 16 24-9 2 24-10 7 24-11 9 24-12 5 16 16 7 3 3 5 3 8 2 2 12 11 9 24-21 10 9 24-22 4 24-24 16 24-25 8 24-26 24-27 7 7 24-28 24 24 250 280 A 250 325 A 80 - - 280 A 35 110 250 325 A 110 250 280 A 80 110 250 280 D(A,B, F, G) A(C, D, E) 2 80 110 250 280 D - - - - A 2 80 110 250 280 D 2 80 24-5 1 100 A 1 80 110 250 280 D 4 45 110 250 - D 16 8 110 110 7 3 12 80 35 3 6 A 280 8 24-5 250 A 8 24-6 100 D(A, G, H)A(all others) 8 24-6 250 24-51 5 24-52 1 HV 24-53 5 24-56 11 9 24-57 24 24 24-58 13 7 3 24-59 14 7 7 24-60 7 24-62 24 24-63 24 D(A, G, H)A(all others) 80 - - 280 80 110 250 280 I - - - - A 5 - - - A 30 KVdc, 21 KVac 2 45 E=Al.; F=Ch.; Balance=Cu 24-28 45 7 24 - - - A - - - - A - - - A 24-28 24-28 16 16 14 15 4 24-66 24-67 24-68 24-71 A, C, J, V, Y, W, K, E, H, U, S, M=Ch.; Balance=Al. - - 24-20 3 24 24-65 E 5 1 24-64 A 280 - - - 250 100 - 24-20 SERVICE RATING 110 24-6 24-19 Z A, C,=Con.; B, D=Cu 24-7 Y 80 16 14 X 80 24-17 2 0 7 4 2 24-16 8 3 24-5 24-15 DEGREES OF ROTATION CONTACTS SIZES A,C, E, G=Ir.; B, D, F, H=Con.; R,T=Ch.; S, U=Al.;Balance=Cu A, C, E, G, J, L, K, N, S, U, W, Y=Cu; B, D, F, H, Q, R, M, P, T, V, X, Z=Con. 24-5 A, B, C, D, E, F, G, H=Ir.; J, K, L, M, N, P, R, S=Con. 11 - - - - A 7 7 - - - - D 19 19 80 - - 335 I 24 7 7 - - - - A 24-75 7 7 - - - - A 24-79 5 5 - 108 - - A 24-80 23 - - - - I 24-81 16 24-84 19 24-96 28 28 25 25 24-AJ 28-1 9 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series SERIES 14 23 19(18) 6 3 24-28 D=Con.; Balance=Cu 24-7 A, C, E, G, I, K, M, N, P=Cu; B, D, F, H, J, L, O=Con. - - - - A/Coax - - - - I 80 110 250 280 A 80 110 250 280 D(A, E, J) A(all others) = Reduced contact crimp pot ( ) = Number of contacts that are coax For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 65 Layouts by Shell Size N AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series W Mating Face view of pin inserts X Z Alternate Insert Position (Rotation) Y SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) SERIES LAYOUT 97 AIT AIB 28-2 14 28-3 3 28-4 28-8 28-5 28-6 28-7 DEGREES OF ROTATION CONTACTS SIZES P-lok TOTAL 20 16 12 12 2 9 7 2 5 2 1 8 4 0 3 3 12 10 6 2 W X Y Z SERVICE RATING 35 110 250 325 D 70 145 215 290 E 80 110 250 280 E(G, P, S)D(allothers) 2 35 110 250 325 D 3 70 145 215 290 D 2 2 35 110 250 325 D 80 110 250 280 E(L, M) B(D) A(all others) 28-9 12 28-10 7 28-11 22 18 28-12 26 26 28-13 26 26 28-12 11 11 80 110 250 280 D A 28-14 6 3 2 2 4 80 110 250 280 D 80 110 250 280 D(G) A(all others) 80 110 250 280 A 90 180 270 - A 100 A 28-15 35 35 80 110 250 280 28-16 20 20 80 110 250 280 A 28-17 15 15 80 110 250 280 A(A-L) B(R) D(M-P) 28-18 12 12 70 145 215 290 E(M) D(G, H, J, K, L) 28-19 10 6 4 80 110 250 280 A(C, E, G, J, K, L) 28-20 14 4 10 80 110 250 280 28-21 A(A, B) I(C, D, E, F) B(H, M) D(A, B) 37 37 28-22 6 3 28-51 12 28-53 22 18 4 28-58 14 4 10 28-59 17 10 7 28-61 37 37 3 12 80 110 250 280 A 70 145 215 290 D 135 195 - A 80 28-11 45 J, L=Al.; K, M=Ch.; Balance=Cu 28-20 45 A, C, E, G, K, M=Al.; B, D, F, H, L, N=Ch.; J, P=Cu - A 28-21 - - - A 45 A, C, J, Z, m, r, n, a, K, F, H, X, k, h, T, M, N, d=Ir.; Balance=Con. 28-63 14 4 28-64 35 35 28-65 26 26 28-66 16 28-72 3 28-74 16 9 28-75 16 28-79 16 28-82 6 28-84 9 10 28-20 45 A, C, E, G, J=Al.; B, D, F, H, P=Ch.; Balance=Cu 28-15 A, d=Al.; B, j=Ch.; C, D, E, F, G, N, P, R, S, H, J, K, 28-12 A, C, E, G, J, L, N, R, T, V=Ir.; X, Z=Al.; B, D, F, H, L, M, W, X, Y, Z=Con.;Balance=Cu K, M, P, S, U, W=Con.;Y, a=Ch.; b, d=Cu 66 = Reduced contact crimp pot 14 2 - - - - A - - - - Coax 7 - - - - A 9 7 - - - - A 9 7 - - - - A 2 - - - - D 9 - - - - A 3(3) 4 ( ) = Number of contacts that are coax For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) LAYOUT 97 DEGREES OF ROTATION CONTACTS SIZES AIT AIB P-lok TOTAL 20 16 12 28-67 20 20 28-68 35 35 28-69 22 18 4 28-70 22 18 4 28-77 22 18 4 28-81 37 37 28-AY 9 5 32A29 23 16 32A30 5 32-1 32-2 5 2 32-3 9 4 2 32-4 14 2 12 8 4 0 W X Y AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series SERIES SERVICE RATING Z 28-16 U=Con.; Balance=Cu 28-15 45 T=Al.; U=Ch.; Balance=Cu 28-11 G=Al.; R=Ch.; Balance=Cu 28-11 A=Al.; B=Ch.; Balance=Cu 28-11 J=Con.; Balance=Cu 28-21 A, D, S, Z, n, s=Ir.; B, J, K, f, g, r=Con.; G, L, P, b, e, j=Al.; F, H, T, X, h, k=Ch.; Balance=Cu 2 3 3 5 4 - 2 32-6 250 A 2 32-1 100 E(A) D(all others) 3 2 3 2 1 - - - A 80 110 250 280 70 145 215 290 E 80 110 250 280 D 80 110 250 280 A(F, J, K, N) D(all others) 35 110 250 325 D 80 110 250 280 A E(A) D(all others) 32-5 2 32-6 23 16 2 32-7 35 28 7 80 125 235 280 I(A, B, H, J) A(all others) 32-8 30 24 6 80 125 235 280 A 2 32-9 14 12 32-10 7 3 32-12 15 10 32-13 23 18 32-15 8 32-16 23 3 2 2 80 110 250 280 D 2 80 110 250 280 E(A, F) B(G) 5 80 110 250 280 A(C, D, E, F, G) 5 80 110 250 280 D 35 110 250 280 D - - - - A 110 250 - 2 D(E) A(D) D(all others) 16 2 4 32-19 5 32-20 23 16 32-22 54 54 32-25 25 32-31 31 31 32-51 30 24 32-52 8 32-53 42 37 5 32-55 30 24 6 32-56 30 24 32-57 8 32-58 4 32-60 23 15 32-62 23 16 32-64 54 54 32-68 16 12 32-73 46 46 32-75 9 2 32-76 19 19 32-79 5 32-82 16 12 52 52 32-17 32-414 6 2 3 2 4 3 2 45 2 3 2 25 6 6 2 260 32-6 260 60 125 80 125 - 6 280 A - - A 215 280 A 90M=Ch.; N= Al.; Balance=Cu - - - D - - - I/E 125M, N=Ch.; O, P=Al.; Balance=Cu - - - - A - - - Coax - - - - Coax - - - - A/Coax - - - - A/Coax - - - - I 65 135 225 275 A/Coax 36 68 - - A - - - - Coax 80 110 250 280 A 4 - - - - D 4 - - - - A - - - - A 4(4) 8(8) 2 4(4) 7(7) 1 32-8 250 - 2(2) 3 (2) A 110 32-8 D E(A) D(all others) 80 - 6 2 32-1 = Reduced contact crimp pot ( ) = Number of contacts that are coax For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com 67 Specifications subject to change. Layouts by Shell Size N AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series W Mating Face view of pin inserts X Z Alternate Insert Position (Rotation) Y SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) SERIES LAYOUT 97 32-AF 36-1 36-3 AIT AIB P-lok TOTAL 20 16 55 55 22 6 12 8 4 3 0 3 W X Y Z SERVICE RATING 80 110 250 280 A 80 110 250 280 D 70 145 215 290 D 3 3 70 145 215 290 A(B, C) D(A) 36-5 4 4 45 120 240 - A 36-6 6 2 35 110 250 325 A 36-7 47 40 7 80 110 250 280 A 36-8 47 46 1 80 110 250 280 A 36-9 31 14 14 80 125 235 280 A 36-10 48 48 80 125 235 280 A 36-11 48 48 36-10 100 36-12 48 48 36-10 250 16 6 36-4 36-14 5 2 1 5 90 A A 180 270 - D 125 245 305 D(m) A(all others) 35 35 47 40 7 36-7 100 A 36-17 47 40 7 36-7 250 A 36-18 31 14 14 2 1 36-9 100 A 36-20 34 30 2 2 36-21 31 14 14 2 1 36-9 36-51 4 36-52 52 36-54 39 31 36-55 39 31 36-59 53 50 36-60 47 40 36-64 4 36-65 4 36-71 53 36-73 7 36-74 44 44 - - - - A 36-75 48 48 - - - - A 36-76 47 47 36-77 7 36-78 14 36-79 20 20 36-80 20 20 36-83 7 52 52 - - - - A 35 35 - - - - A/D 36-403 36-85 4 36-16 36-15 DEGREES OF ROTATION CONTACTS SIZES 60 2 2 - - A A - - - - D - - - - A 8 - 110 - - A 8 - - - - A 3 - - - - A 7 - - - - A 4(4) - - - - Coax 4(4) - - - - Coax - - - - A 81 279 - - Coax 52 50 260 3 7(7) 7 2 12 7(7) - - - - A 81 279 - - D 85 106 254 325 A 30 110 250 330 A 30 110 250 330 A 81 279 - - Coax = Reduced contact crimp pot ( ) = Number of contacts that are coax 68 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Layouts by Shell Size SERIES KEY: AIB (=GT) AIT (=MS; =non QPL) 97 (=97) P-lok () Thermocouple () CONTACT METALLURGY KEY: Alumel (Al.) Chromel (Ch.) Constantan (Con.) Copper (Cu) Iron (Ir.) LAYOUT 97 AIT AIB DEGREES OF ROTATION CONTACTS SIZES P-lok TOTAL 20 16 12 7 36-53 47 40 36-56 48 48 36-57 47 40 8 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series SERIES 4 0 W 36-7 X Y SERVICE RATING Z 45 u, v, w=Al.; x, y, z=Ch.; Balance=Cu 36-10 A, C, E, G, L, J, H, P, R, T, V, X, Z, b, d, f, h, k, q, 36-8 W=Al.; f=Ch.; Balance=Cu 36-15 H=Al.; G=Ch.; Balance=Cu 36-15 A, C, E, J, K, L, M, N, P, R, T, V, f, X, Y, h, j, 36-10 A, C, E=Al.; B, D, F=Ch.; Balance=Cu 36-52 65 33 65 70 v, g=Ir.; p, y, c=Con. x=Ch.; Balance=Cu 130 235 300 270 125 225 310 130 230 290 n, m, u, w, y=Con.; Balance=Cu 36-58 35 35 36-61 35 35 36-62 48 48 36-82 36-AF 40-1 40-5 40-9 40-10 40-35 52 48 30 5 47 29 35 52 48 24 40-53 40-56 40-57 40-61 40-62 40-63 40-64 40-66 40-67 40-68 40-70 40-72 40-73 40-74 40-75 60 85 4 59 60 61 36 4 11 21 61 11 61 6 5 60 85 40-80 40-81 40-85 40-86 40-87 11 62 60 4 7 1 62 60 40-58 85 85 40-59 85 85 40-77 60 60 40-78 60 60 40-AG 38 7 c=Con.; Balance=Cu 4 5 24 16 22 1 9 4 35 4 55 60 61 20 3 1 3 13(13) 4(4) 1 10(10) 21 61 1 61 10(10) 1 1 1(1) 4(4) 4 10 4(4) 7 38 A D A A A D 80 72 30 - 110 144 150 - 250 216 - 280 288 - A A E A A A Coax Coax A/Coax A A A/Coax A A/Coax E 80 37 74 285 280 322 A A A E/Coax D 40-56 40-56 A, C, E, H, K, M, P, S, U, W, Y, a, c, f, h, j, m, p, r, t, v, x, z, AB, AD, AF, AJ, AL,AN, AP, AS, AU, AW, AY, BA, BC, BE, BH, BK, BM, BP, BS, BU=Ir.; Balance=Con. B=Ch.; C=Con.; Balance=Cu 40-56 55, 60=Ir.; 57, 58, 59=Con.; 56=Ch.; Balance=Cu 40-53 50, 51=Ir.; 27, 28, 29, 31, 32, 34, 36, 37=Con.; 25, 39, 40, 41=Al.; 43,44,45, 46, 47, 48, 49, 52, 53, 54=Ch.; Balance=Cu 37 74 285 322 A Z * * * * * * SERVICE RATING I A A A A D = Reduced contact crimp pot ( ) = Number of contacts that are coax Special Inserts Available LAYOUT 32-48 32-59 40-82 40-AD 40-AT 40-AV 97 SERIES AIT AIB P-lok TOTAL 48 42 62 8 43 3 20 16 48 40 62 18 CONTACT SIZES 12 8 4 0 2 24 4 1 4 3#2/0 DEGREES OF ROTATION W X Y 80 * * * * * * * * * * * * * * * * * * Call for details. For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 69 Pin & Socket Crimp Contacts PIN CONTACT WIRE STRIP LENGTH SOCKET CONTACT WIRE RANGE AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series PART NUMBER PIN CONTACT WIRE SIZE SILVER GOLD SILVER GOLD 16S 16-18-20 AIC16S-16P AIC16S-16PG AIC16S-16S AIC16S-16SG 12-14 AIC16S-12P AIC16S-12PG AIC16S-12S AIC16S-12SG C4 14-16 18-20 AIC16S-14P AIC16S-20P AIC16S-14PG AIC16S-20PG AIC16S-14S AIC16S-20S AIC16S-14SG AIC16S-20SG C3 C13 20-22 AIC16S-22P AIC16S-22PG AIC16S-22S AIC16S-22SG C14 22-24 AIC16S-24P AIC16S-24PG AIC16S-24S AIC16S-24SG C2 16-18-20 AIC16-16P AIC16-16PG AIC16-16S AIC16-16SG 12-14 AIC16-12P AIC16-12PG AIC16-12S AIC16-12SG 14-16 AIC16-14P AIC16-14PG AIC16-14S AIC16-14SG C3 18-20 AIC16-18P AIC16-18PG AIC16-18S AIC16-18SG C13 AIC16-20S AIC16-20SG C14 16S 16 16 AIC16-20P AIC16-20PG 20-24 AIC16-2024P AIC16-2024PG 22-24 AIC16-22P AIC16-22PG AIC16-22S AIC16-22SG 12-14 AIC12-12P AIC12-12PG AIC12-12S AIC12-12SG 8-10 AIC12-8P AIC12-8PG AIC12-8S AIC12-8SG C5 10-12 AIC12-10P AIC12-10PG AIC12-10S AIC12-10SG C8 14-16 AIC12-14P AIC12-14PG AIC12-14S AIC12-14SG C9 16-18 AIC12-16P AIC12-16PG AIC12-16S AIC12-16SG C7 18-20 AIC12-18P AIC12-18PG AIC12-18S AIC12-18SG C6 20-22 AIC12-20P AIC12-20PG AIC12-20S AIC12-20SG C40 8 AIC8-8P AIC8-8PG AIC8-8S AIC8-8SG 8 High Power - - AIC8-8SRAD - 10-12 AIC8-10P AIC8-10PG AIC8-10S AIC8-10SG C10 12-14 AIC8-12P AIC8-12PG AIC8-12S AIC8-12SG C38 4 4 AIC4-4P AIC4-4PG AIC4-4S AIC4-4SG 4 4 High Power - - AIC4-4SRAD - 8 AIC4-8P AIC4-8PG AIC4-8S AIC4-8SG 0 0 AIC0-0P AIC0-0PG AIC0-0S AIC0-0SG 0 0 High Power - - AIC0-0SRAD - AIC0-2PG AIC0-4PG AIC0-2S AIC0-4S AIC0-2SG AIC0-4SG 12 8 8 0-2 AIC0-2P 4 AIC0-4P Bolded items are standard crimp contacts 16S 16S 16 16 AIC16-2024S AIC16-2024SG SOLDER THERMOCOUPLE CONTACTS TYPE PINS SOCKETS Alumel 10-040799-02P* 10-040799-02S* Chromel 10-040799-01P* 10-040799-01S* Iron 10-040799-03P* 10-040799-03S* Constantan 10-040799-04P* 10-040799-24S* Alumel 10-040799-12P* 10-040799-12S* Chromel 10-040799-11P* 10-040799-11S* Iron 10-040799-13P* 10-040799-13S* Constantan 10-040799-14P* 10-040799-14S* .090-.118 (2.3-3.0) .312 (7.9) C4 20-22 12 70 WIRE STRIP WIRE SEALING RANGE LENGTHS INCHES (mm) INCHES (mm) SOCKET CONTACT CONTACT SIZE C36 C2 .312 (7.9) .312 (7.9) .126-.177 (3.2-4.5) .563 (14.3) .150-.256 (3.8-6.5) .500 (12.7) .279-.366 (7.1-9.3) C15 . C11 C12 .750 (19.0) 394-.539 (10.0-13.7) SOLDER THERMOCOUPLE CONTACTS 12 12 TYPE Alumel Chromel Iron Constantan PINS 10-040799-42P* 10-040799-41P* 10-040799-43P* 10-040799-44P* SOCKETS 10-040799-42S* 10-040799-41S* 10-040799-43S* 10-040799-44S* Thermocouple Types: J = Iron-Constantan K = Alumel-Chromel T = Copper-Constantan E = Chromel-Constantan *Call for availability 16S contacts are used in 8S, 10S, 10SL, 12S, 14S and 16S connector sizes only. For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Pin & Socket Crimp Contacts AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series TOOLS ACCESSORIES AF8 400BHD WA27F TH29-1 WIRE HOLE FILLER (COLOR) CRIMP TOOLS 414DA CRIMP LOCATOR & DIE SETS LOCATOR COLOR PILOT PIN/INSERTION GUIDE FOR SOCKETS INSERTION TOOL 10-242758-016 DAK168-16 EXTRACTION TOOL Red MS27488-16-1 (Blue) AF8 (hand) WA27F (pneumatic) TH29-1 Pin-Blue Socket-Green DRK59 Kit with Multiple Tips MS27488-12-1 (Yellow) MS27488-8-1 (White) MS27488-4-1 (Blue) 400BHD . MS27488-0-1 (Yellow) Locator 414DA-8N Die Set 4025-Pin 4026-Socket Locator 414DA-4N Die Set 4043 Locator 414DA-0N Die Set 4042 Green 10-242758-012 DAK168-12 - 10-242758-008 DAK282 - - AIC4INS AIC4EXT - - AIC0INS AIC0EXT Call for additional tool accessories. 71 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Pin & Socket Coax Contacts COAX SOCKET WIRE STRIP LENGTH WIRE RANGE ACCESSORIES SOCKETS WIRE STRIP LENGTHS WIRE SEALING RANGE INCHES (mm) MIN. MAX. WIRE HOLE FILLER AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series COAX PIN PART NUMBERS COAX CONTACT SIZE 12 COAX WIRE SIZE RG161/U RG174A/U RG179B/U RG187A/U RG188A/U RG316/U PINS SILVER GOLD SILVER GOLD 21-33034-1 21-33014-21 21-33048-1() 21-33130-1() 21-33033-1 21-33013-21 21-33047-1() 21-33129-1 () RG178B/U RG196A/U RG58C/U RG141A/U RG303/U RG59B/U RG62A/U RG62B/U RG210/U 8 4 RG161/U RG174A/U RG179B/U RG187A/U RG188A/U RG316/U 21-33014-22 21-33034-2(1) 21-33014-1(5) 21-33016-5(3) 21-33130-2() 31-33034-5(1) 21-33014-5(5) 21-33016-2(3) 21-33130-5() 21-33064-21() 21-33034-3(1) INCHES (mm) 0.177 0.126 Yellow (3.2 mm) (4.5 mm) 10-405996-12 Call for details 21-33013-22 21-33033-2(1) 21-33048-2() 21-33013-1(5) 21-33047-2() 21-33015-5(3) 21-33129-2() 21-33033-3(1) 21-33013-5(5) 21-33015-2(3) 21-33129-3() 21-33063-21() 21-33033-3(1) 21-33013-3(5) 21-33015-1(3) 21-33129-3() 21-33063-20() - 21-33014-3(5) 21-33016-1(3) 21-33130-3 () 21-33064-20() 0.256 0.150 White Call for details (3.8 mm) (6.5 mm) 10-405996-8 - RG180B/U RG195A/U 21-33034-6 21-33014-6(5) 21-33048-3() 21-33130-6() RG140/U RG302/U 21-33034-8 21-33014-8(5) 21-33033-8 21-33130-8() RG55B/U RG142A/U RG142B/U RG223/U 21-33034-4 21-33014-5(5) 21-33130-4() 21-33033-6 21-33013-(6) 21-33047-3() 21-33129-6() 21-33013-8(5) 21-33129-8() 21-33033-4 21-33013-5(5) 21-33129-4() RG59B/U RG62A/U RG62B/U RG210/U 21-33060-10() 21-33059-10() RG212/U 21-33060-11() 21-33059-11() RG55B/U RG142A/U RG142B/U RG223/U 31-33060-12() 21-33059-12() Call for details Blue 0.366 0.279 (7.1 mm) (9.3 mm) 10-405996-4 ( ) Various platings available. Availability of coax contacts varies widely. Call for details. 72 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Pin & Socket Coax Contacts M22520/10-01 COAX CONTACT SIZE 12 COAX WIRE SIZE RG161/U RG174A/U RG179B/U RG187A/U RG188A/U RG316/U M22520/5-01 HAND CRIMP TOOL CRIMP DIE/LOCATOR M22520/10-01 M22520/10-05 Crimp Dies USE LOCATOR 11-8676-1 B RG58C/U RG141A/U RG303/U M22520/10-01 M22520/10-07 B 11-8676-2 RG59B/U RG62A/U RG62B/U RG210/U M22520/5-01 M22520/5-45 B 11-8676-3 RG161/U RG174A/U RG179B/U RG187A/U RG188A/U RG316/U M22520/10-05 A - RG180B/U RG195A/U B 11-8676-2 M22520/10-01 RG140/U RG302/U M22520/10-07 A RG55B/U RG142A/U RG142B/U RG223/U 4 COAX CLAMP NUT WRENCH A RG178B/U RG196A/U 8 AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series TOOLS RG59B/U RG62A/U RG62B/U RG210/U M22520/5-01 M22520/5-45 B RG212/U M22520/5-01 M22520/5-39 A RG55B/U RG142A/U RG142B/U RG223/U M22520/10-01 M22520/10-07 A 11-8676-4 73 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Components Plugs AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series AIB/GT Receptacles AIBC/ACA-B AIB/GT AIBC/ACA-B O-Ring Barrel/Shell Insert/ Insulator Contacts Wave Spring and Skid Washer (Optional) Coupling Nut Individual Wire Sealing Grommet Ferrule/Sleeve Compression Ring Endbell/ Backshell/ Cable Clamp 74 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions Printed Circuit Contacts AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series S D P .138 X SHELL SIZE 10SL H SERIES S X .188 (4.78) .567 (14.40) 14S .188 (4.78) .567 (14.40) 16S .188 (4.78) .567 (14.40) 16 .188 (4.78) .622 (15.80) 18 .188 (4.78) .622 (15.80) 20 .188 (4.78) .622 (15.80) 22 .188 (4.78) .622 (15.80) 24 .188 (4.78) .622 (15.80) 28 .188 (4.78) .657 (16.69) 32 .188 (4.78) .720 (18.29) 36 .188 (4.78) .720 (18.29) 40 .188 (4.78) .720 (18.29) CONTACT SIZE 12 16 D P .134 (3.4) .070 (1.78) .063 (1.6) .030 (0.76) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 75 Dimensions Style 0, 2, 20, 30 Receptacles AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 0, 20, 30 RV T R 0, 20, 30 2 S KK2 M P M P R N KK N S L B L M N P SHELL +.016-.000 +.000-.006 .008 SIZE (+0.4-0.0) (+0.00-0.15) (0.2) 10SL .717 .717 .110 (18.20) (18.2) (2.8) 76 L R S T .004 (0.1) .012 (0.3) +.004-.000 (+0.1-0.0) .717 (18.2) 1.000 (25.4) .126 (3.2) KK MAX. .626 (15.9) B THREAD CLASS 2A .6250-24 UNEF L + .012 (+ 0.3) 1.087 (27.6) L MAX. 1.890 (48.0) KK2 MAX. .787 (20.0) 14S .717 (18.20) .969 (24.6) .126 (3.2) .906 (23.0) 1.181 (30.0) .126 (3.2) .756 (19.2) .7500-20 UNEF 1.087 (27.6) 1.890 (48.0) .945 (24.0) 16S .717 (18.20) 1.079 (27.4) .126 (3.2) .969 (24.6) 1.280 (32.5) .126 (3.2) .882 (22.4) .8750-20 UNEF 1.087 (27.6) 1.890 (48.0) 1.024 (26.0) 16 .846 (21.50) 1.079 (27.4) .126 (3.2) .969 (24.6) 1.280 (32.5) .126 (3.2) .882 (22.4) .8750-20 UNEF 1.331 (33.8) 2.205 (56.0) 1.024 (26.0) 18 .907 (23.05) 1.213 (30.8) .157 (4.0) 1.063 (27.0) 1.378 (35.0) .126 (3.2) 1.008 (25.6) 1.0000-20 UNEF 1.331 (33.8) 2.244 (57.0) 1.161 (29.5) 20 .907 (23.05) 1.346 (34.2) .157 (4.0) 1.157 (29.4) 1.496 (38.0) .126 (3.2) 1.142 (29.0) 1.1250-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.299 (33.0) 22 .907 (23.05) 1.472 (37.4) .157 (4.0) 1.252 (31.8) 1.614 (41.0) .126 (3.2) 1.268 (32.2) 1.2500-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.417 (36.0) 24 .907 (23.05) 1.610 (40.9) .157 (4.0) 1.374 (34.9) 1.752 (44.5) .146 (3.7) 1.390 (35.3) 1.3750-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.575 (40.0) 28 .947 (24.05) 1.839 (46.7) .157 (4.0) 1.563 (39.7) 2.000 (50.8) .146 (3.7) 1.630 (41.4) 1.6250-18 UNEF 1.406 (35.7) 2.244 (57.0) 1.811 (46.0) 32 .947 (24.05) 2.102 (53.4) .157 (4.0) 1.752 (44.5) 2.244 (57.0) .169 (4.3) 1.882 (47.8) 1.8750-16 UN 1.469 (37.3) 2.362 (60.0) 2.028 (51.5) 36 .947 (24.05) 2.346 (59.6) .157 (4.0) 1.937 (49.2) 2.500 (63.5) .169 (4.3) 2.063 (52.4) 2.0625-16 UN 1.469 (37.3) 2.362 (60.0) 2.283 (58.0) 40 .947 (24.05) 2.579 (65.5) .157 (4.0) 2.185 (55.5) 2.752 (69.9) .169 (4.3) 2.323 (59.0) 2.3125-16 UN 1.469 (37.3) 2.362 (60.0) 2.539 (64.5) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions Style 0, 20, 30 Receptacles AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series L F G B Thread B Thread F F K Z BB JJ K J L1 L2 K L B THREAD CLASS 2A .6250-24 UNEF F MIN. .409 (10.4) K MIN. .374 (9.5) L1 MAX. 1.969 (50) L2 MAX. 3.017 (76.6) J .008 (0.2) .138 (3.5) K + .020 (0.5) .461 (11.7) L MAX. 1.969 (50) Z MIN. .303 (7.7) BB MAX. .524 (13.3) JJ + .008 (+0.2) .610 (15.5) .7500-20 UNEF .520 (13.2) .374 (9.5) 1.969 (50) 3.048 (77.4) .138 (3.5) .461 (11.7) 1.969 (50) .417 (10.6) .669 (17.0) .752 (19.1) .8750-20 UNEF .638 (16.2) .374 (9.5) 1.969 (50) 3.048 (77.4) .138 (3.5) .461 (11.7) 1.969 (50) .531 (13.5) .862 (21.9) .941 (23.9) .8750-20 UNEF .638 (16.2) .374 (9.5) 2.362 (60) 3.304 (83.9) .138 (3.5) .453 (11.5) 2.362 (60) .531 (13.5) .862 (21.9) .941 (23.9) 1.0000-20 UNEF .756 (19.2) .374 (9.5) 2.362 (60) 3.419 (86.8) .138 (3.5) .453 (11.5) 2.362 (60) .575 (14.6) .862 (21.9) .941 (23.9) 1.1875-18 UNEF .867 (22.0) .374 (9.5) 2.362 (60) 3.404 (86.5) .138 (3.5) .500 (12.7) 2.559 (65) .736 (18.7) 1.031 (26.2) 1.165 (29.6) 1.1875-18 UNEF .965 (24.5) .374 (9.5) 2.362 (60) 3.408 (86.6) . .138 (3.5) .500 (12.7) 2.559 (65) .819 (20.8) 1.031 (26.2) 1.165 (29.6) 1.4375-18 UNEF 1.094 (27.8) .374 (9.5) 2.560 (65) 3.495 (88.8) .138 (3.5) .500 (12.7) 2.559 (65) .969 (24.6) 1.358 (34.5) 1.488 (37.8) 1.4375-18 UNEF 1.228 (31.2) .374 (9.5) 2.560 (65) 3.629 (92.2) . .138 (3.5) .500 (12.7) 2.559 (65) 1.063 (27.0) 1.358 (34.5) 1.488 (37.8) 1.7500-18 UNS 1.488 (37.8) .433 (11.0) 2.560 (65) 3.777 (95.9) .138 (3.5) .598 (15.2) 2.756 (70) 1.311 (33.3) 1.717 (43.6) 1.882 (47.8) 2.0000-18 UNS 1.780 (45.2) .465 (11.8) 3.150 (80) 3.821 (97.0) .138 (3.5) .598 (15.2) 3.150 (80) 1.516 (38.5) 1.717 (43.6) 1.882 (47.8) 2.2500-16 UN 2.016 (51.2) .465 (11.8) 3.150 (80) 3.821 (97.0) .138 (3.5) .610 (15.5) 3.150 (80) 1.898 (48.2) 2.071 (52.6) 2.276 (57.8) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 77 Dimensions Style 1 Cable Receptacle AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series M P B RV KK N Q S L L M +.016 -.000 (+0.4 - 0.0) .717 (18.20) N +.000 -.006 (+0.00-0.15) .717 (18.2) P .008 (0.2) .110 (2.8) Q .008 S (0.2) MAX. .811 .992 (20.6) (25.2) L B + .012 THREAD (+ 0.3) CLASS 2A .6250-24 UNEF 1.087 (27.6) 14S .717 (18.20) .969 (24.6) .126 (3.2) 1.000 (25.4) 1.173 (29.8) .7500-20 UNEF 16S .717 (18.20) 1.079 (27.4) .126 (3.2) 1.126 (28.6) 1.272 (32.3) 16 .8461 (21.50) 1.079 (27.4) .126 (3.2) 1.126 (28.6) 18 .907 (23.05) 1.213 (30.8) .157 (4.0) 20 .907 (23.05) 1.346 (34.2) 22 .907 (23.05) 24 L MAX. 1.890 (48.0) KK MAX. .787 (20.0) 1.087 (27.6) 1.890 (48.0) .945 (24.0) .8750-20 UNEF 1.087 (27.6) 1.890 (48.0) 1.024 (26.0) 1.272 (32.3) .8750-20 UNEF 1.331 (33.8) 2.205 (56.0) 1.024 (26.0) 1.248 (31.7) 1.370 (34.8) 1.0000-20 UNEF 1.331 (33.8) 2.244 (57.0) 1.161 (29.5) .157 (4.0) 1.374 (34.9) 1.488 (37.8) 1.1250-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.299 (33.0) 1.472 (37.4) .157 (4.0) 1.500 (38.1) 1.618 (41.1) 1.2500-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.417 (36.0) .907 (23.05) 1.610 (40.9) .157 (4.0) 1.626 (41.3) 1.756 (44.6) 1.3750-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.575 (40.0) 28 .947 (24.05) 1.839 (46.7) .157 (4.0) 1.874 (47.6) 2.004 (50.9) 1.6250-18 UNEF 1.406 (35.7) 2.244 (57.0) 1.811 (46.0) 32 .947 (24.05) 2.102 (53.4) .157 (4.0) 2.126 (54.0) 2.248 (57.1) 1.8750-16 UN 1.469 (37.3) 2.362 (60.0) 2.028 (51.5) 36 .947 (24.05) 2.346 (59.6) .157 (4.0) 2.386 (60.6) 2.504 (63.6) 2.0625-16 UN 1.469 (37.3) 2.362 (60.0) 2.283 (58.0) 40 .947 (24.05) 2.579 (65.5) .157 (4.0) 2.618 (66.5) 2.756 (70.0) 2.3125-16 UN 1.469 (37.3) 2.362 (60.0) 2.539 (64.5) SHELL SIZE 10SL 78 All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions Style 1 Cable Receptacle AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series B Thread F G F Z BB JJ K B Thread L1 L J K F L K L2 F MIN. .409 (10.4) K MIN. .374 (9.5) L1 MAX. 1.969 (50) L2 MAX. 3.684 (93.6) J .008 (0.2) .138 (3.5) K + .020 (0.5) .461 (11.7) L MAX. 1.969 (50) Z MIN. .303 (7.7) BB MAX. .524 (13.3) JJ + .008 (+0.2) .610 (15.5) .7500-20 UNEF .520 (13.2) .374 (9.5) 1.969 (50) 3.748 (95.2) .138 (3.5) .461 (11.7) 1.969 (50) .417 (10.6) .669 (17.0) .752 (19.1) .8750-20 UNEF .638 (16.2) .374 (9.5) 1.969 (50) 3.748 (95.2) .138 (3.5) .461 (11.7) 1.969 (50) .531 (13.5) .862 (21.9) .941 (23.9) .8750-20 UNEF .638 (16.2) .374 (9.5) 2.362 (60) 3.71 (94.2) .138 (3.5) .453 (11.5) 2.362 (60) .531 (13.5) .862 (21.9) .941 (23.9) 1.0000-20 UNEF .756 (19.2) .374 (9.5) 2.362 (60) 4.094 (104.0) .138 (3.5) .453 (11.5) 2.362 (60) .575 (14.6) .862 (21.9) .941 (23.9) 1.1875-18 UNEF .867 (22.0) .374 (9.5) 2.362 (60) 4.094 (104.0) .138 (3.5) .500 (12.7 2.559 (65) .736 (18.7) 1.031 (26.2) 1.165 (29.6) 1.1875-18 UNEF .965 (24.5) .374 (9.5) 2.362 (60) 4.102 (104.2) . .138 (3.5) .500 (12.7) 2.559 (65) .819 (20.8) 1.031 (26.2) 1.165 (29.6) 1.4375-18 UNEF 1.094 (27.8) .374 (9.5) 2.560 (65) 3.950 (100.4) .138 (3.5) .500 (12.7) 2.559 (65) .969 (24.6) 1.358 (34.5) 1.488 (37.8) 1.4375-18 UNEF 1.228 (31.2) .374 (9.5) 2.560 (65) 4.392 (111.6) . .138 (3.5) .500 (12.7) 2.559 (65) 1.063 (27.0) 1.358 (34.5) 1.488 (37.8) 1.7500-18 UNS 1.488 (37.8) .433 (11.0) 2.560 (65) 5.038 (128.0) .138 (3.5) .598 (15.2) 2.756 (70) 1.311 (33.3) 1.717 (43.6) 1.882 (47.8) 2.0000-18 UNS 1.780 (45.2) .465 (11.8) 3.150 (80) 4.354 (110.6) .138 (3.5) .598 (15.2) 3.150 (80) 1.516 (38.5) 1.717 (43.6) 1.882 (47.8) 2.2500-16 UN 2.016 (51.2) .465 (11.8) 3.150 (80) 4.354 (110.6) .138 (3.5) .610 (15.5) 3.150 (80) 1.898 (48.2) 2.071 (52.6) 2.276 (57.8) B THREAD CLASS 2A .6250-24 UNEF All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 79 Dimensions Style 4 Rubber-Covered Plugs AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Q RV B KK S L L B THREAD CLASS 2A .6250-24 UNEF L + .012 (+ 0.3) 1.087 (27.6) L MAX. 1.890 (48.0) KK MAX. .787 (20.0) 1.713 (43.5) 1.0000-20 UNEF 1.331 (33.8) 2.244 (57.0) 1.161 (29.5) 2.028 (51.5) 1.811 (46.0) 1.1250-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.299 (33.0) 22 2.224 (56.5) 1.988 (50.5) 1.2500-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.417 (36.0) 24 2.362 (60.0) 2.126 (54.0) 1.3750-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.575 (40.0) 28 2.638 (67.0) 2.402 (61.0) 1.6250-18 UNEF 1.406 (35.7) 2.244 (57.0) 1.811 (46.0) 32 2.992 (76.0) 2.661 (67.6) 1.8750-16 UN 1.469 (37.3) 2.362 (60.0) 2.028 (51.5) 36 3.240 (82.3) 2.925 (74.3) 2.0625-16 UN 1.469 (37.3) 2.362 (60.0) 2.283 (58.0) 40 3.465 (88.0) 3.150 (80.0) 2.3125-16 UN 1.469 (37.3) 2.362 (60.0) 2.539 (64.5) SHELL SIZE 10SL Q MAX. 1.319 (33.5) S MAX. 1.122 (28.5) 18 1.929 (49.0) 20 80 All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions Style 4 Rubber-Covered Plugs L AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series F G B Thread B Thread F F K Z BB JJ K J L1 L2 K L B THREAD CLASS 2A .6250-24 UNEF JJ + .008 (+0.2) F MIN. .409 (10.4) K MIN. .374 (9.5) L1 MAX. 1.969 (50) L2 MAX. 3.684 (93.6) J .008 (0.2) .138 (3.5) K + .020 (0.5) .461 (11.7) L MAX. 1.969 (50) Z MIN. .303 (7.7) BB MAX. .524 (13.3) 1.0000-20 UNEF .756 (19.2) .374 (9.5) 2.362 (60) 4.094 (104.0) .138 (3.5) .453 (11.5) 2.362 (60) .575 (14.6) .862 (21.9) .941 (23.9) 1.1875-18 UNEF .867 (22.0) .374 (9.5) 2.362 (60) 4.094 (104.0) .138 (3.5) .500 (12.7) 2.559 (65) .736 (18.7) 1.031 (26.2) 1.165 (29.6) 1.1875-18 UNEF .965 (24.5) .374 (9.5) 2.362 (60) 4.102 (104.2) . .138 (3.5) .500 (12.7) 2.559 (65) .819 (20.8) 1.031 (26.2) 1.165 (29.6) 1.4375-18 UNEF 1.094 (27.8) .374 (9.5) 2.560 (65) 3.950 (100.4) .138 (3.5) .500 (12.7) 2.559 (65) .969 (24.6) 1.358 (34.5) 1.488 (37.8) 1.4375-18 UNEF 1.228 (31.2) .374 (9.5) 2.560 (65) 4.392 (111.6) . .138 (3.5) .500 (12.7) 2.559 (65) 1.063 (27.0) 1.358 (34.5) 1.488 (37.8) 1.7500-18 UNS 1.488 (37.8) .433 (11.0) 2.560 (65) 5.038 (128.0) .138 (3.5) .598 (15.2) 2.756 (70) 1.311 (33.3) 1.717 (43.6) 1.882 (47.8) 2.0000-18 UNS 1.780 (45.2) .465 (11.8) 3.150 (80) 4.354 (110.6) .138 (3.5) .598 (15.2) 3.150 (80) 1.516 (38.5) 1.717 (43.6) 1.882 (47.8) 2.2500-16 UN 2.016 (51.2) .465 (11.8) 3.150 (80) 4.354 (110.6) .138 (3.5) .610 (15.5) 3.150 (80) 1.898 (48.2) 2.071 (52.6) 2.276 (57.8) .610 (15.5) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 81 Dimensions Style 6, 6HD Plugs AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 6 6HD RV B KK Q1 82 L Q2 L B THREAD CLASS 2A .6250-24 UNEF L + .012 (+ 0.3) 1.087 (27.6) L MAX. 1.890 (48.0) KK MAX. .787 (20.0) 1.259 (31.9) .7500-20 UNEF 1.087 (27.6) 1.890 (48.0) .945 (24.0) 1.260 (32.0) 1.410 (35.8) .8750-20 UNEF 1.087 (27.6) 1.890 (48.0) 1.024 (26.0) 16 1.260 (32.0) 1.410 (35.8) .8750-20 UNEF 1.331 (33.8) 2.205 (56.0) 1.024 (26.0) 18 1.437 (36.5) 1.547 (39.2) 1.0000-20 UNEF 1.331 (33.8) 2.244 (57.0) 1.161 (29.5) 20 1.571 (39,9) 1.681 (42.6) 1.1250-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.299 (33.0) 22 1.697 (43.1) 1.847 (46.9) 1.2500-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.417 (36.0) 24 1.835 (46.6) 1.965 (49.9) 1.3750-18 UNEF 1.331 (33.8) 2.244 (57.0) 1.575 (40.0) 28 2.102 (53.4) 2.222 (56.4) 1.6250-18 UNEF 1.406 (35.7) 2.244 (57.0) 1.811 (46.0) 32 2.366 (60.1) 2.482 (63.0) 1.8750-16 UN 1.469 (37.3) 2.362 (60.0) 2.028 (51.5) 36 2.610 (66.3) 2.721 (69.1) 2.0625-16 UN 1.469 (37.3) 2.362 (60.0) 2.283 (58.0) 40 2.850 (72.4) 2.953 (75.0) 2.3125-16 UN 1.469 (37.3) 2.362 (60.0) 2.539 (64.5) SHELL SIZE 10SL Q1 MAX. .898 (22.8) Q2 MAX. 1.007 (25.5) 14S 1.150 (29.2) 16S All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions Style 6, 6HD Plugs L AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series F G B Thread B Thread F F K Z BB JJ K J L2 L1 K L F MIN. .409 (10.4) K MIN. .374 (9.5) L1 MAX. 1.969 (50) L2 MAX. 3.684 (93.6) J .008 (0.2) .138 (3.5) K + .020 (0.5) .461 (11.7) L MAX. 1.969 (50) Z MIN. .303 (7.7) BB MAX. .524 (13.3) JJ + .008 (+0.2) .610 (15.5) .7500-20 UNEF .520 (13.2) .374 (9.5) 1.969 (50) 3.748 (95.2) .138 (3.5) .461 (11.7) 1.969 (50) .417 (10.6) .669 (17.0) .752 (19.1) .8750-20 UNEF .638 (16.2) .374 (9.5) 1.969 (50) 3.748 (95.2) .138 (3.5) .461 (11.7) 1.969 (50) .531 (13.5) .862 (21.9) .941 (23.9) .8750-20 UNEF .638 (16.2) .374 (9.5) 2.362 (60) 3.71 (94.2) .138 (3.5) .453 (11.5) 2.362 (60) .531 (13.5) .862 (21.9) .941 (23.9) 1.0000-20 UNEF .756 (19.2) .374 (9.5) 2.362 (60) 4.094 (104.0) .138 (3.5) .453 (11.5) 2.362 (60) .575 (14.6) .862 (21.9) .941 (23.9) 1.1875-18 UNEF .867 (22.0) .374 (9.5) 2.362 (60) 4.094 (104.0) .138 (3.5) .500 (12.7 2.559 (65) .736 (18.7) 1.031 (26.2) 1.165 (29.6) 1.1875-18 UNEF .965 (24.5) .374 (9.5) 2.362 (60) 4.102 (104.2) .138 (3.5) .500 (12.7) 2.559 (65) .819 (20.8) 1.031 (26.2) 1.165 (29.6) 1.4375-18 UNEF 1.094 (27.8) .374 (9.5) 2.560 (65) 3.950 (100.4) .138 (3.5) .500 (12.7) 2.559 (65) .969 (24.6) 1.358 (34.5) 1.488 (37.8) 1.4375-18 UNEF 1.228 (31.2) .374 (9.5) 2.560 (65) 4.392 (111.6) .138 (3.5) .500 (12.7) 2.559 (65) 1.063 (27.0) 1.358 (34.5) 1.488 (37.8) 1.7500-18 UNS 1.488 (37.8) .433 (11.0) 2.560 (65) 5.038 (128.0) .138 (3.5) .598 (15.2) 2.756 (70) 1.311 (33.3) 1.717 (43.6) 1.882 (47.8) 2.0000-18 UNS 1.780 (45.2) .465 (11.8) 3.150 (80) 4.354 (110.6) .138 (3.5) .598 (15.2) 3.150 (80) 1.516 (38.5) 1.717 (43.6) 1.882 (47.8) 2.2500-16 UN 2.016 (51.2) .465 (11.8) 3.150 (80) 4.354 (110.6) .138 (3.5) .610 (15.5) 3.150 (80) 1.898 (48.2) 2.071 (52.6) 2.276 (57.8) B THREAD CLASS 2A .6250-24 UNEF All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 83 Dimensions Plug Style 6, 6HD Right Angle AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 6 6HD T J B F Q1 84 L Q2 SHELL SIZE 10SL Q1 MAX. .898 (22.8) Q2 MAX. 1.007 (25.5) 14S 1.150 (29.2) 16S B THREAD CLASS 2A F MAX. J MIN. K MAX. L MAX. .6250-24 UNEF .337 (8.5) .370 (9.4) 1.181 (30.0) 1.772 (45.0) 1.259 (31.9) .7500-20 UNEF .462 (11.7) .370 (9.4) 1.181 (30.0) 1.850 (47.0) 1.260 (32.0) 1.410 (35.8)) .8750-20 UNEF .587 (14.9) .370 (9.4) 1.181 (30.0) 1.890 (48.0) 16 1.260 (32.0) 1.410 (35.8)) .8750-20 UNEF .587 (14.9) .370 (9.4) 1.181 (30.0) 2.244 (57.0) 18 1.437 (36.5) 1.547 (39.2) 1.0000-20 UNEF .685 (17.4) .370 (9.4) 1.378 (35.0) 2.283 (58.0) 20 1.571 (39,9) 1.681 (42.6) 1.1875-18 UNEF .810 (20.5) .370 (9.4) 1.378 (35.0) 2.402 (61.0) 22 1.697 (43.1) 1.847 (46.9) 1.1875-18 UNEF .915 (23.2) .370 (9.4) 1.378 (35.0) 2.402 (61.0) 24 1.835 (46.6) 1.965 (49.9) 1.4375-18 UNEF 1.025 (26.0) .370 (9.4) 1.575 (40.0) 2.598 (66.0) 28 2.102 (53.4) 2.222 (56.4) 1.4375-18 UNEF 1.139 (28.9) .370 (9.4) 15.75 (40.0) 2.598 (53.4) 32 2.366 (60.1) 2.482 (63.0) 1.7500-18 UNEF 1.447 (36.7) .433 (11.0) 1.772 (45.0) 2.835 (72.0) 36 2.610 (66.3) 2.721 (69.1) 2.0000-18 UNS 1.687 (42.8) .496 (12.6) 1.969 (50.0) 2.953 (75.0) 40 2.850 (72.4) 2.953 (75.0) 2.2500-16 UN 1.923 (48.8) .496 (12.6) 2.165 (55.1) 3.071 (78.0) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions 6B Panel Plug Style TB Thru-Bulkhead Receptacle 6B AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series M P TB P N N Q S R L L T S T R R S R S SHELL Q L SIZE APPROX. MAX. 10SL 1.087 .898 (27.6) (22.8) P .008 (0.2) .110 (2.8) R S T .004 .012 +.004-.000 (0.1) (0.3) (+0.1-0.0) .717 1.000 .126 (18.2) (25.4) (3.2) S R P M N T L +.016-.000 +.000-.006 .008 .004 .012 +.004-.000 Max. (+0.4-0.0) (+0.00-0.15) (0.2) (0.1) (0.3) (+0.1-0.0) 1.488 .717 .717 .110 .717 1.000 .126 (37.7) (18.2) (18.2) (2.8) (18.2) (25.4) (3.2) 14S 1.091 (27.7) 1.150 (29.2) .126 (3.2) .906 (23.0) 1.181 (30.0) .126 (3I.2) 1.488 (37.7) .717 (18.2) .969 (24.6) .126 (3.2) .906 1.181 (23.0) (30.0) .126 (3.2) 16S 1.091 (27.7) 1.260 (32.0) .126 (3.2) .969 (24.6) 1.280 (32.5) .126 (3.2) 1.488 (37.7) .717 (18.2) 1.079 (24.6) .126 (3.2) .969 1.280 (23.0) (30.0) .126 (3.2) 16 1.469 (37.3) 1.260 (32.0) .126 (3.2) .969 (24.6) 1.280 (32.5) .126 (3.2) 2.049 (52.0) .846 (21.5) 1.079 (27.4) .126 (3.2) .969 1.280 (24.6) (32.5) .126 (3.2) 18 1.500 (38.1) 1.437 (36.5) .157 (4.0) 1.063 (27.0) 1.378 (35.0) .126 (3.2) 2.049 (52.0) .907 (23.0) 1.213 (30.8) .157 (4.0) 1.063 1.378 (27.0) (35.0) .126 (3.2) 20 1.500 (38.1) 1.571 (39.9) .157 (4.0) 1.157 (29.4) 1.496 (38.0) .126 (3.2) 2.049 (52.0) .907 (23.0) 1.346 (34.2) .157 (4.0) 1.157 1.496 (29.4) (38.0) .126 (3.2) 22 1.500 (38.1) 1.697 (43.1) .157 (4.0) 1.252 (31.8) 1.614 (41.0) .126 (3.2) 2.049 (52.0) .907 (23.0) 1.472 (37.4) .157 (4.0) 1.252 1.614 (31.8) (41.0) .126 (3.2) 24 1.598 (40.6) 1.835 (46.6) .157 (4.0) 1.374 (34.9) 1.752 (44.5) .146 (3.7) 2.049 (52.0) .90 (23.0) 1.610 (40.9) .157 (4.0) 1.374 1.752 (34.9) (44.5) .146 (3.7) 28 1.626 (41.3) 2.102 (53.4) .157 (4.0) 1.563 (39.7) 2.000 (50.8) .146 (3.7) 2.049 (52.0) .947 (24.0) 1.839 (46.7) .157 (4.0) 1.563 2.000 (39.7) (50.8) .146 (3.7) 32 1.764 (44.8) 2.366 (60.1) .157 (4.0) 1.752 (44.5) 2.244 (57.0) .169 (4.3) 2.049 (52.0) .947 (24.0) 2.102 (53.4) .157 (4.0) 1.752 2.244 (44.5) (57.0) .160 (4.3) 36 1.764 (44.8) 2.610 (66.3) .157 (4.0) 1.937 (49.2) 2.500 (63.5) .169 (4.3) 2.049 (52.0) .947 (24.0) 2.346 (59.6) .157 (4.0) 1.937 2.500 (49.2) (63.5) .169 (4.3) 40 1.764 (44.8) 2.850 (72.4) .157 (4.0) 2.185 (55.5) 2.752 (69.9) .169 (4.3) 2.049 (52.0) .947 (24.0) 2.579 (65.5) .157 (4.0) 2.185 2.752 (55.5) (69.9) .160 (4.3) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 85 Dimensions Style 7, 70 Jam Nut Receptacles AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series 7 70 L M S M J G J P P G N S N B BB B O-Ring O-Ring R B SHELL THREAD SIZE CLASS 2A 10SL .8750-20 UNEF 86 J G .012 WALL THICKNESS MIN. MAX. (0.3) .441 .094 .205 (11.2) (2.4) (5.2) N M L P R .010 .012 +.000-.0006 .007 .016 (0.3) (0.3) (+0.00-0.15) (0.2) (0.4) 1.425 .965 .717 .157 1.062 (36.2) (24.5) (18.2) (4.0) (27) S .12 (0.3) 1.252 (31.8) BB THREAD CLASS 2A .6250-24 UNEF 14S 1.1250-18 UNEF .575 (14.6) .094 (2.4) .295 (7.5) 1.531 1.055 (38.9) (26.8) .969 (24.6) .189 (4.8) 1.312 (33) 1.626 (41.3) .7500-20 UNEF 16S 1.2500-180 UNEF .618 (15.7) .094 (2.4) .295 (7.5) 1.531 1.055 (38.9) (26.8) 1.079 (27.4) .189 (4.8) 1.500 (38) 1.748 (44.4) .8750-20 UNEF 16 1.2500-18 UNEF .618 (15.7) .094 (2.4) .295 (7.5) 1.909 1.264 (48.5) (32.1) 1.079 (27.4) .189 (4.8) 1.500 (38) 1.748 (44.4) .8750-20 UNEF 18 1.3750-18 UNEF .661 (16.8) .094 (2.4) .354 (9.0) 1.941 1.327 (49.3) (33.7) 12.13 (30.8) .189 (4.8) 1.562 (40) 1.874 1.0000-20 UNEF (47.6) 20 1.5000-18 UNEF .709 (18.0) .094 (2.4) .358 (9.1) 1.941 1.327 (49.3) (33.7) 1.346 (34.2) .189 (4.8) 1.750 (44) 2.000 1.1250-18 UNEF (50.8) 22 1.6250-18 UNEF .795 (20.2) .094 (2.4) .358 (9.1) 1.941 1.327 (49.3) (33.7) 1.472 (37.4) .189 (4.8) 2.000 (51) 2.252 1.2500-18 UNEF (57.2) 24 1.75000-18 UNEF .795 (20.2) .094 (2.4) .358 (9.1) 1.953 1.327 (49.6) (33.7) 1.610 (40.9) .189 (4.8) 2.000 (51) 2.252 1.3750-18 UNEF (57.2) 28 2.0000-18 UNS .886 (22.5) .094 (2.4) .394 (10.0) 2.043 1.386 (51.9) (35.2) 1.839 (46.7) .220 (5.6) 2.188 (56) 2.500 1.6250-18 UNEF (63.5) 32 2.2500-16 UN .972 (24.7) .094 (2.4) .394 (10.0) 2.043 1.386 (51.9) (35.2) 2.102 (53.4) .220 (5.6) 2.438 (62) 2.748 (69.8) 1.8750-16 UN 36 2.5000-16 UN 1.059 (26.9) .094 (2.4) .327 (8.3) 2.043 1.386 (51.9) (35.2) 2.346 (59.6) .220 (5.6) 2.812 (71) 3.000 (76.2) 2.0625-16 UN 40 2.7500-16 UN 1.165 (29.6) .094 (2.4) .327 (8.3) 2.043 1.386 (51.9) (35.2) 2.579 (65.5) .220 (5.6) 3.000 (76) 3.248 (82.5) 2.3125-16 UN All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Dimensions Panel Cutouts AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series STYLE 0, 2, 20, 30, TB FLANGE SHELL SIZE G G J K H Dia. Dim. J-flange in front of panel Dim. K-flange at rear of panel See sealing screws on page 257. 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 40 G (TP) 0.717 0.811 0.906 0.969 0.969 1.063 1.157 1.252 1.374 1.563 1.752 1.937 2.185 (18.2) (20.6) (23.0) (24.6) (24.6) (27.0) (29.4) (31.8) (34.9) (39.7) (44.5) (49.2) (55.5) MOUNTING HOLE DIAMETER H 0.134 0.134 0.134 0.134 0.134 0.134 0.134 0.134 0.154 0.154 0.177 0.177 0.177 (3.4) (3.4) (3.4) (3.4) (3.4) (3.4) (3.4) (3.4) (3.9) (3.9) (4.5) (4.5) (4.5) SHELL SIZE D J FRONT 0.646 0.646 0.776 0.902 0.902 1.028 1.161 1.287 1.417 1.654 1.902 2.150 2.409 (16.4) (16.4) (19.7) (22.9) (22.9) (26.1) (29.5) (32.7) (36.0) (42.0) (48.3) (54.6) (61.2) K REAR 0.728 0.854 0.980 1.091 1.091 1.224 1.358 1.488 1.626 1.854 2.118 2.362 2.610 (18.5) (21.7) (24.9) (27.7) (27.7) (31.1) (34.5) (37.8) (41.3) (47.1) (53.8) (60.0) (66.3) 7/70 PANEL CUTOUT F - FLAT D - DIAMETER 10SL 14S 16S/16 18 20 22 24 28 32 36 40 0.830 1.080 1.210 1.320 1.450 1.570 1.700 1.950 2.200 2.450 2.700 (21.1) (27.4) (30.7) (33.5) (36.8) (39.9) (43.2) (49.5) (55.9) (62.2) (68.6) SHELL SIZE REAR MOUNT 0.875 1.125 1.250 1.375 1.500 1.625 1.750 2.000 2.250 2.500 2.750 (22.2) (28.6) (31.7) (34.9) (38.1) (41.3) (44.5) (50.8) (57.2) (63.5) (69.9) Panel Thickness Rear Mount 10SL 14S 16S 16 18 20 22 24 28 32 36 40 .303 .303 .303 .242 .303 .303 .303 .303 .343 .309 .309 .309 (7.70) (7.70) (7.70) (6.15) (7.70) (7.70) (7.70) (7.70) (8.70) (7.85) (7.85) (7.85) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 87 Accessories MS3057-A Cable Clamp AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Standard MS3057 cable clamps have a dual clamping action to provide a balanced, positive hold on the wires and greatly reduce moisture transmission. This cable clamp accepts MS3420 bushings. MS3420 bushings can be nested to reduce the inside diameter to more closely match the diameter of the cable or wire bundle. STANDARD CLAMP SHELL SIZE 8S 10S/10SL 12/12S/12SL 14/14S 16/16S 18 20/22 24/28 32 36 40 THREAD 2B 1/2-24UNEF 5/8-24UNEF 5/8-24UNEF 3/4-20UNEF 7/8-20UNEF 1-20UNEF 1 3/16-18UNEF 1 7/16-18UNEF 1 3/4-18UNS 2-18UNS 2 1/4UNS-16 LOW COST CAST ZINC 97-3057-1003 97-3057-1004 97-3057-1004 97-3057-1007 97-3057-1008 97-3057-1010 97-3057-1012 97-3057-1016 97-3057-1020 97-3057-1024 - ALUMINUM W/ MAXIMUM ALUMINUM W/ STAINLESS STEEL CABLE DIAMETER BRASS SCREWS SCREWS INCH (mm) MS3057-3A M85049/41-3A .220 (5.58) MS3057-4A M85049/41-4A .312 (7.92) MS3057-4A M85049/41-4A .312 (7.92) MS3057-6A M85049/41-6A .438 (11.13) MS3057-8A M85049/41-8A .562 (14.27) MS3057-10A M85049/41-10A .625 (15.88) MS3057-12A M85049/41-12A .750 (19.05) MS3057-16A M85049/41-16A .938 (23.83) MS3057-20A M85049/41-20A 1.250 (31.75) MS3057-24A M85049/41-24A 1.375 (34.92) MS3057-28A M85049/41-28A 1.625 (41.28) STANDARD CLAMP AND TELESCOPIC BUSHING LOW COST ZINC WITH BUSHING BUSHING ID BUSHING INCLUDED INCH (mm) 97-3057-1003-1 MS3420-3 0.130 (3.3) 97-3057-1004-1 MS3420-4 0.220 (5.6) 97-3057-1004-1 MS3420-4 0.220 (5.6) 97-3057-1007-1 MS3420-6 0.312 (7.9) 97-3057-1008-1 MS3420-8 0.437 (11.1) 97-3057-1010-1 MS3420-10 0.562 (14.3) 97-3057-1012-1 MS3420-12 0.625 (15.9) 97-3057-1016-1 MS3420-16, -12 0.625 (15.9) 97-3057-1020-1 MS3420-20, -16 0.750 (19.1) 97-3057-1024-1 MS3420-24, -20 0.937 (23.8) - MS3057-C Waterproof Cable Clamp NEOPRENE SEALING GLAND METAL COMPRESSION DISC SHELL SIZE 88 CABLE CLAMP Standard MS3057-C waterproof cable clamp with mechanical strain relief for use with style F, L and T endbells. Internal neoprene gland and compression ring will seal a broad range of round cable diameters as listed below. For reduction of cable diameters, order the appropriate MS3420A bushing in table. WIRE DIAMETER INCHES (mm) PART NUMBER MAX. MIN. 10SL 14S MS3057-4C MS3057-6C .312 (7.93) .438 (11.12) .188 (4.80) .281 (7.10) 16/16S MS3057-8C .530 (13.48) .312 (7.90) 18 MS3057-10C .625 (15.87) .375 (9.50) 20/22 MS3057-12C .750 (19.00) .500 (12.70) 24/28 MS3057-16C .940 (23.8) .625 (15.90) 32 MS3057-20C 1.25 (31.75) - 36 MS3057-24C 1.38 (35.00) 1.00 (25.40) 40 MS3057-28C 1.62 (41.25) 1.25 (31.80) OPTIONAL BUSHINGS PART NUMBER MAX. WIRE DIA. (mm) MS3420-4A MS3420-6A MS3420-4A MS3420-8A MS3420-6A MS3420-10A MS3420-6A MS3420-12A MS3420-8A MS3420-16A MS3420-12A MS3420-8A MS3420-20A MS3420-16A MS3420-12A MS3420-24A MS3420-18A MS3420-16A MS3420-28A MS3420-20A MS3420-16A .219 (5.56) .312 (7.93) .219 (5.56) .438 (11.10) .312 (7.93) .438 (11.10) .312 (7.93) .540 (13.74) .438 (11.10) .750 (19.00) .540 (13.74) .438 (11.10) .938 (23.80) .750 (19.00) .540 (13.74) 1.12 (28.5) .938 (23.80) .750 (19.00) 1.25 (31.75) .940 (23.80) .750 (19.00) All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Accessories MS3420 Telescoping Bushings AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series For use with style A cable clamps and AIT/MS style E/F endbells to eliminate dust, dirt and oil from entering the cable clamp. Bushings can be nested, one inside the other, to reduce the inside diameter and form a better seal against the cable jacket. Each bushing will accept the next smallest bushing. 1ST BUSHING PART NUMBER MS3420-4 INSIDE DIAMETER .220 (5.59) 2ND NESTED BUSHING FITS IN CABLE CLAMP MS3057-4A NONE INSIDE DIAMETER - 12S MS3420-4 .220 (5.59) NONE - MS3057-4A 14S MS3420-6 .312 (7.92) NONE - MS3057-6A 16S MS3420-8 .437 (11.10) NONE - MS3057-8A 16 MS3420-8 .437 (11.10) NONE - MS3057-8A 18 MS3420-10 .562 (14.30) NONE - MS3057-10A 20 MS3420-12 .625 (15.90) NONE - MS3057-12A 22 MS3420-12 .625 (15.90) NONE - MS3057-12A 24 MS3420-16 .750 (19.05) MS3420-12 .625 (15.90) MS3057-16A 28 MS3420-16 .750 (19.05) MS3420-12 .625 (15.90) MS3057-16A 32 MS3420-20 .937 (23.80) MS3420-16 .750 (19.05) MS3057-20A 36 MS3420-24 1.250 (31.75) MS3420-20 .937 (23.80) MS3057-24A 40 MS3420-28 1.375 (34.92) MS3420-24 1.250 (31.75) SE96-28A4 SIZE 10SL MS3420-A Reduction Bushings For use with MS3057-C cable clamps (Style C) to reduce the wire sealing diameter. Bushings can be nested, one inside the other, to progressively reduce the inside diameter of the cable clamp. The column labeled "reduction bushings" shows the acceptable nesting options for each clamp. 9767 Cable Clamps 9767 waterproof cable clamp with mechanical strain relief. An internal neoprene gland seal bushing and compression washer will seal a broad range of round cable diameters as listed below. MAX. CABLE OD MIN. CABLE OD THREAD CLASS 2B 10SL, 12S CABLE CLAMP PART NUMBER 9767-12-4 INCHES 0.219 (mm) (5.55) INCHES 0.020 (mm) (0.51) 5/8-24 UNEF 14S 9767-14-4 0.219 (5.55) 0.020 (0.51) 3/4-20 UNEF SHELL SIZE 14S 9767-14-6 0.344 (8.73) 0.176 (4.47) 3/4-20 UNEF 16S, 16 9767-16-4 0.219 (5.55) 0.020 (0.51) 7/8-20 UNEF 16S, 16 9767-16-6 0.344 (8.73) 0.176 (4.47) 7/8-20 UNEF 16S, 16 9767-16-8 0.438 (11.12) 0.177 (4.50) 7/8-20 UNEF 18 9767-18-6 0.344 (8.73) 0.176 (4.47) 1-20 UNEF 18 9767-18-8 0.438 (11.12) 0.177 (4.50) 1-20 UNEF 18 9767-18-10 0.563 (14.29) 0.292 (7.42) 1-20 UNEF 20, 22 9767-22-8 0.438 (11.12) 0.177 (4.50) 1-3/16-18 UNEF 20, 22 9767-22-10 0.563 (14.29) 0.292 (7.42) 1-3/16-18 UNEF 20, 22 9767-22-12 0.688 (17.46) 0.370 (9.40) 1-3/16-18 UNEF 24, 28 9767-28-10 0.563 (14.29) 0.292 (7.42) 1-7/16-18 UNEF 24, 28 9767-28-12 0.688 (17.46) 0.370 (9.40) 1-7/16-18 UNEF 24, 28 9767-28-16 0.844 (21.43) 0.536 (13.61) 1-7/16-18 UNEF 32 9767-32-20 1.031 (26.19) 0.590 (14.99) 1-3/4-18 UNS 36 9767-36-16 0.844 (21.43) 0.536 (13.61) 2-18 UNS All dimensions in inches (millimeters in parenthesis) For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. 89 Accessories Gaskets AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Synthetic rubber gaskets are used to insure a moisture tight seal between a receptacle and the panel. Gaskets are available for front or rear panel mounting of style 0, 2, 20, 30 and TB connectors. Gasket thickness is approximately .031" (1 mm), for nonconductive and low temperature types. Conductive shielding gaskets contain an imbedded metal screen for EMI/RFI shielding in addition to moisture sealing. Gaskets are available for front or rear panel mounting of style 30 and TB connectors. Gasket thickness is .020" (.5 mm). REAR MOUNT FRONT MOUNT SHELL SIZE 10SL 14S 16S 16 18 20 22 24 28 32 36 40 NON-CONDUCTIVE 10-040450-010 10-040450-014 10-040450-016 10-040450-016 10-040450-018 10-040450-020 10-040450-022 10-040450-024 10-040450-028 10-040450-032 10-040450-036 10-040450-040 CONDUCTIVE 10-040450-10S 10-040450-14S 10-040450-16S 10-040450-16S 10-040450-18S 10-040450-20S 10-040450-22S 10-040450-24S 10-040450-28S 10-040450-32S 10-040450-36S 10-040450-40S NON-CONDUCTIVE 10-580649-011 10-580649-014 10-580649-016 10-580649-016 10-580649-018 10-580649-020 10-580649-022 10-580649-024 10-580649-026 10-580649-032 10-580649-036 10-580649-040 LOW TEMPERATURE 10-036675-010 10-036675-014 10-036675-016 10-036675-016 10-036675-018 10-036675-020 10-036675-022 10-036675-024 10-036675-028 10-036675-032 10-036675-036 10-036675-040 Metal Dust Caps With Sash Chain Metal dust caps are used to protect the contacts when the connectors are left unmated. Dust caps come with metal chain lanyards. Dummy Receptacles are for front or rear panel mounting. AIB/GT Series connectors have bayonet ramps. The center of the connector is closed. Dummy receptacles mount on the same centers and have the same outside dimensions as a STYLE 2 receptacle. A version with a clearance hole through the middle of the connector is also available. Call for ordering information. PLUG CAP DUST CAPS RECEPTACLE DUMMY RECEPTACLES PLUG SEAL RING 1,8 0,2 D9 SHELL SIZE 10SL 14S 16S 16 18 20 22 24 28 32 36 40 3 10-580903-11* 10-580903-14* 10-580903-16* 10-580903-17* 10-580903-18* 10-580903-20* 10-580903-22* 10-580903-24* 10-580903-28* 10-580903-32* 10-580903-36* 10-580903-40* *Select code for plating: Z = Black anodize 3 = Olive drab cadmium plate 10-580902-11* 10-580902-14* 10-580902-16* 10-580902-17* 10-580902-18* 10-580902-20* 10-580902-22* 10-580902-24* 10-580902-28* 10-580902-32* 10-580902-36* 10-580902-40* 10-580595-11* 10-580595-14* 10-580595-16* 10-580595-17* 10-580595-18* 10-580595-20* 10-580595-22* 10-580595-24* 10-580595-28* 10-580595-32* 10-580595-36* 10-580595-40* 9 = Olive drab cadmium nickel base G = Electroless nickel 0,2 10-564843-101 10-564843-141 10-564843-161 10-564843-161 10-564843-181 10-564843-201 10-564843-221 10-564843-241 10-564843-281 10-564843-321 10-564843-161 10-564843-401 U = Green zinc cobalt Y = Black Zinc cobalt 90 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Assembly Instructions Crimp Tool Operation 1. Slide the rear accessories over the wire bundle in the proper sequence for re-assembly: cable clamp and/or endbell first, then ferrule and (if used) coupling nut. NOTE: Hand crimp tools can be used with size 16S, 16 & 12 contacts. Size 8, 4 and 0 contacts require the use of air powered crimp tools. Call us for assistance in the use of these tools. 4. AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Solder Contacts Adjust dial for proper wire gauge. To change the dial setting, remove the lock pin and lift center of dial. Turn to the desired wire gauge. Replace lock pin on dial. DIAL 2. Open the crimp tool by squeezing the handles. Push the latch on the turret to pop up the locator. Attach the turret to the crimp tool using the two captive hex bolts in the turret. LOCATOR 4. Fixture the connector for reassembly using the endbell page 96. assembly tools on 7. Slide coupling nut, ferrule, and endbell accessories over rear of the connector and tighten. For tooling, see page 96. TE 6. Fill all unused grommet cavities with a wire hole filler to maintain the sealing integrity of the connector. (page 73). CRIMP TOOL 5. Cycle the tool before inserting the contact to be sure the tool is in the open position. Drop the contact, mating end first, into the crimp cavity of the tool. Squeeze the tool handle just enough to grip the contact without actually crimping it. ISE TO ROTA RA SE L 5. Slide the grommet down the wires (lubricating the grommet with isopropyl alcohol will help). LATCH . NO 3. Solder wires to appropriate contacts on the rear of the connector. A document covering standard soldering practices is available upon request by fax or mail. Please call. LOCK PIN 24 26 WIR E 22 1 SEL 32 E SIZ Insert individual wires through the proper holes in the grommet. Use isopropyl alcohol as a lubricant. 14 16 18 2 0 12 654 87 2. 1. Strip the wires to the appropriate length. See strip lengths on the Contact Selection Guide, page 72. DM 3. Select the proper locator position for your contact by rotating the locator until the proper color is aligned with the index mark. Push locator back down until it snaps into position. CONTACT SIZE 16S 16 12 PIN LOCATOR COLOR Red Blue Green 6. Insert the stripped wire into the contact with a slight twisting motion. Be sure all wire strands are inside the contact. Squeeze the handle to cycle the tool. The handle will not release until the contact is completely crimped. SOCKET LOCATOR COLOR Red Green Green LATCH LOCATOR LOCATOR COLOR CODE INDEX MARK TURRET 91 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Assembly Instructions AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Crimp Tool Operation Insertion of Contacts (continued) 1. Slide the rear accessories over the wire bundle in the proper sequence for re-assembly: cable clamp and/or endbell first, then ferrule, and coupling nut. 7. Remove the crimped contact. Pull on the wire slightly to be sure it is properly crimped. Be sure the contact is not bent or damaged in any way. Visually inspect the crimp: CHECK TO BE SURE CONDUCTOR IS VISIBLE THROUGH WIRE INSPECTION HOLE CRIMP 4. Place the connector into an assembly fixture (fixtures are available for production use, call us.) If you are not using a fixture, be sure to allow clearance on the mating face of the connector for the guide pins to come through the connector during insertion. CONNECTOR 2. Use the proper insertion tool from the Contact Selection Chart on page 73. Place the contact in the tool. The tool should butt against the shoulder of the contact. Contact sizes 16S, 16, and 12 use a pliers style tool. Contact sizes 8, 4 and 0 use a tool with a `C' shaped shaft. WIRE INSULATION SHOULD BUTT UP AGAINST THE END OF THE CONTACT. MICRO-SECTIONS Enlargement of micro-section permits a final inspection of crimp quality. This test is recommended whenever new tools or new types of wire or contacts are used. GUIDE (PILOT) PIN INSERTION TOOL SHOULDER ASSEMBLY FIXTURE 5. Lubricate the contact cavities of the connector insulator with isopropyl alcohol (do not use any other type of lubricant). Crimp Tensile Strength Initial minimum pullout force in lb. (before conditioning) SIZE WIRE GAUGE LB. 16 20 18 16 14 12 8 4 0 20 40 50 70 110 185 450 800 12 8 4 0 3. Lubricate the grommet with isopropyl alcohol (do not use any lubricant other than isopropyl alcohol). Insert the contact through the appropriate cavity in the grommet. Sizes 16S, 16 and 12 socket contacts must be installed using guide pins. See the Contact Selection Guide on page 73 for Insertion Guide (Pilot) Pin part numbers. 6. Using guide pins where necessary, push straight down with a firm even pressure until the contact snaps into position in the proper cavity. Start at the center of the pattern and work toward the outer edges. 92 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Assembly Instructions 7. Fill any unused cavities with contacts. UNCRIMPED CONTACTS 9. A wire hole filler must be inserted into the grommet behind the unused contacts to maintain the sealing integrity of the connector. See the Contact Selection Chart on page 73 for wire hole fillers. AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series Insertion of Contacts 2. Use the proper extraction tool from the Contact Selection Chart on page 73. The extraction tool can be used for both pin and socket contacts by removing the shaft from the handle and reversing it for pin or socket extraction. SOCKET EXTRACTION END LOCK RING HANDLE PIN EXTRACTION END 8. Check the mating face of the connector to insure that all the same size contacts are on the same plane (fully inserted). If not, the contact is not fully inserted. Remove the contact using the proper extraction tool and procedure and reinsert. Do not attempt to reinsert the insertion tool to correct the problem. 10. Place the connector back in the fixture for re-assembly. Slide the connector accessories back down the cable over the rear of the connector and tighten. Use the appropriate endbell tools as shown on page 73. 3. On the mating face of the connector, insert the tool over the pin contact or into the socket contact until the tool bottoms. Apply a slow continuous pressure to push the contact out the rear of the connector. When the shoulder of the tool "thunks" against the insulator, the contact is extracted. CROSS SECTION OF CONNECTOR CROSS SECTION OF CONNECTOR Extraction of Contacts 1. Remove the endbell accessories and slide them back over the wires. Use the appropriate endbell tools as shown on page 96. SOFT JAW PLIERS PIN CONTACT SOCKET CONTACT 4. Carefully remove the extraction tool from the connector to avoid damage to the insulator. 93 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Amphenol How To Order Guide GT C 00 A 36-5 P W - 002 SERIES GT Circular connectors with bayonet coupling CONTACT STYLE/INSERT C = Crimp S = Solder CY = Crimp with Viton SY = Solder with Viton CL = Crimp with low smoke/flame retardant inserts SL = Solder with low smoke/flame retardant inserts CONNECTOR SHELL VARIATIONS Omit for standard olive drab with silver plated contacts G96 Black anodized 014 Olive drab cadmium plate, nickel base A24 Gold/nickel plated contacts 023 Electroless nickel (RoHS with Crimp only) 025 Black zinc cobalt (RoHS with Crimp only) 027 Conductive black zinc cobalt 024 Green zinc cobalt B30 Gold RDS Radsok power contacts 8, 4 & 0 socket contact only New 116 Less pre-tinned solder cups 472 116 & 025 mod codes (RoHS) 548 116 & 023 mod codes (RoHS) AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series AIB/GT Series Connectors ! ALTERNATE INSERT ROTATION "W", "X", "Y", "Z" designates that the insert is rotated in its shell from a normal position. No letter required for normal (no rotation) position. See pages 59-69. CONTACT STYLE P designates pin contacts S designates socket contacts SHELL STYLE 00 Wall mount receptacle 01 Inline receptacle 02 Box mount receptacle 020 Box mount receptacle with accessory threads 030 Square flange receptacle - rear panel mount (Most Popular) 05 Dummy receptacle 06 Straight plug (Most Popular) 062 Straight plug with deep serrated coupling nut* 064 Panel mounted plug with heavy duty coupling nut 065 Straight plug with long heavy duty coupling nut 07 Jam nut receptacle - rear panel mount 070 Jam nut receptacle with accessory threads 08 90 angle plug TB Thru-bulkhead Mateability with identical contact arrangements Connector Style Mateable with Style GT00 GT01 GT02 GT020 GT030 GT06/062/064/065 GT07/070 GT08 GTTB GT06/062/064/065/08 GT06/062/064/065/08 GT06/062/064/065/08 GT06/062/064/065/08 GT06/062/064/065/08 GT00/01/02/020/03/030/05/070/TB GT06/062/064/065/08 GT00/01/02/020/03/030/05/070/TB GT06/062/064/065/08 Have a unique requirement? Doing standard modifications quickly is our specialty! To save cost, minimize lead time, and reduce assembly labor, please call 800-523-0727 for engineering assistance. SHELL SIZE & LAYOUT See pages 50-69. CONNECTOR CLASS A General duty, threaded backshell, no cable clamp, no grommet AF General duty, threaded backshell, cable clamp, no grommet F General duty, threaded backshell, cable clamp, with grommet CF General duty, threaded endbell, gland-seal cable clamp, no grommet CFZ General duty, threaded endbell, gland-seal cable clamp, with grommet G One-piece, heat shrink endbell adaptor, with grommet (use with heat shrink boot - see Accessories, pages 258-260) G2 Two-piece, heat shrink endbell adaptor, with grommet (use with heat shrink boot - see Accessories, pages 258-260) LC Long threaded backshell, gland-seal cable clamp, with grommet, and basket-weave cord grip (please call with cable O.D.) LCF Long threaded endbell, gland-seal cable clamp, no grommet LCFZ Long threaded endbell, gland-seal cable clamp, with grommet R General duty, threaded backshell, no cable clamp, with grommet RV General duty, short backshell, with grommet (may be used with heat shrink boot - see Accessories, pages 258-260) CFGG General duty, threaded endbell, gland-seal cable clamp, no grommet, rubber-covered coupling nut (shell styles 06 and 08 only) PP Panel plug, only for shell styles 06 and 064 LT Long back shell for metal core conduit, with grommet (please call with conduit O.D.) PFC For plastic, flexible conduit (please call with conduit O.D.) see pages 262-263. SL Long backshell for use with PG gland-seal style cord grip (please call with cable O.D.) 94 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Amphenol How To Order Guide AIB/AIBC Amphenol Industrial Bayonet/GT/ACA-B Series AIBC/ACA-B Series Connectors To more easily illustrate ordering procedure, part number ACA3106E181SXB-F80 is shown as follows: ACA 3106 E 18 1 S X B - F80 CONNECTOR MODIFICATION 01 - Metric crimp contacts 116 - Less solder filled contacts F80 - AWG Crimp contacts A176 - Gold plated contacts A23 - Electroless nickel plating shells A232 - Black zinc cobalt plated shells F42 - Less grommet, endbell & sleeve (ferrule) F0 - Less contacts (ordered separately) SERIES ACA Circular Connector Family SHELL STYLES 3100 - Wall mount receptacle with rear accessory threads for front mounting through holes in flange RFI - Grounding spring on barrel (3106 & 3108) 3101 - Cable connecting receptacle with rear accessory threads T00 - Metric threaded holes in flange (3100, 3102, 3103 only) 3102 - Front mount box receptacle no rear accessory threads through holes in flange Consult factory for other modifications REVERSE BAYONET COUPLING 3103 - Rear mount box receptacle with rear accessory threads through holes in flange ALTERNATE POSITION W, X, Y, and Z 3106 - Plug straight 3107A - Jam nut receptacle rear mount no rear accessory threads No suffix required for normal position See pages 59-69 for valid alternate insert position (rotation) 3108 - Plug with 90 degree endbell CONTACT TYPE P - Pin S - Socket CONNECTOR CLASS E F Environmental with resilient insulator and endbell with clamp and bushing CONNECTOR ARRANGEMENT See pages 50-58 for layouts by number of contacts Environmental with resilient insulator and endbell with rear accessory threads G Two piece backshell for heat shrink boots R Environmental with resilient insulator and shortened lightweight endbell without cable clamp SHELL SIZE 10SL, 14S, 16S, 16, 18, 20, 22, 24, 28, 32, and 36 Mateability with identical contact arrangements Connector Style Mateable with Style ACA ACA ACA ACA ACA ACA ACA ACA3106/ ACA3106/ ACA3106/ ACA3106/ ACA3106/ ACA3101/ ACA3101/ 3100 3101 3102 3103 3105 3106 3108 ACA3108 ACA3108 ACA3108 ACA3108 ACA3108 ACA3102/ ACA3103 ACA3102/ ACA3103 Series part numbering system on Use theAIB/GT pages 48-49 whenever possible. 95 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change. Connector Tools TG70 Strap Wrench AIB/AIBCAmphenol AmphenolIndustrial IndustrialBayonet/GT/ACA-B Bayonet/GT/AC-B Series Series AIB/AIBC The strap wrench is used to connect or disconnect coupling nuts in a confined space, or to tighten or loosen endbells without damaging the connector plating. A strap wrench also increases torque, allowing you to more easily mate or unmate a connector pair. Substitute tools, such as a pipe wrench or pliers, should never be used because of the high probability of severe damage to the connector plating or the coupling mechanism. TG69P Non-Marring Adjustable Endbell Pliers For Field Service The TG69P pliers have resilient jaws and are used to tighten or remove endbells without damaging the connector plating. The pliers are adjustable and will accommodate all of the connector sizes in this catalog. Substitute tools, such as a pipe wrench or metal jaw pliers, should never be used due to the high probability of severe damage to the connector plating. Replacement jaws, Part No. G77015, are available. 600 Series Production System The 600 Series is a complete system for the proper assembly and torquing of connector endbells. The System includes a bench mounted or hand-held torque wrench, plug and receptacle holders, and a range of endbell tightening tools. When used together, these tools provide the user with consistent endbell installations. Each item is shipped with detailed assembly instructions. Plug and Receptacle Holders 600-004 600-007 600B005-R Bench mounted Torque wrench Hand held Torque wrench SIZE 8/8S 10S/SL 12/12S 14/14S 16/16S 18 20 22 24 28 32 36 600B005-P MIL-DTL-5015 FOR AIT/MS, AIB/GT, P-lok RECEPTACLES PLUGS 600B005-8R 600B005-8P 600B005-10R 600B005-10P 600B005-12R 600B005-12P 600B005-14R 600B005-14P 600B005-16R 600B005-16P 600B005-18R 600B005-18P 600B005-20R 600B005-20P 600B005-22R 600B005-22P 600B005-24R 600B005-24P 600B005-28R 600B005-28P 600B005-32R 600B005-32P 600B005-36R 600B005-36P 600D005-R 600D005-P MIL-DTL-26482 FOR PT, PT-SE, MS311_, MS312_ RECEPTACLES PLUGS 600D005-8R 600D005-8P 600D005-10R 600D005-10P 600D005-12R 600D005-12P 600D005-14R 600D005-14P 600D005-16R 600D005-16P 600D005-18R 600D005-18P 600D005-20R 600D005-20P 600D005-22R 600D005-22P 600D005-24R 600D005-24P - Torque Values Important Note: If Barrel/Shell have three threads or less, torque to 30 to 35 inch - Lbs (3.4 to 4.0 NM) per L-725-2. SIZE IN./LB. MAX. 10SL 14S 16 16S 18 20 22 24 28 32 36 40 26 44 50 50 55 65 85 90 114 120 153 170 96 For price & delivery: 800-642-8750 * For tech support: 800-523-0727 * www.PeiGenesis.com Specifications subject to change.