12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
21 dB Small Signal Gain
25 dBm P1dB Compression Point
38 dBm Output IP3 Linearity
17 dB Gain Control with Bias Adjust
3x3mm Standard QFN Package
100% RF Testing
Features
Absolute Maximum Ratings1
Supply Voltage (Vd1,2,3)
Supply Current (Id1,2,3)
Gate Bias Voltage (Vg1,2,3)
Max Power Dissipation (Pdiss)
RF Input Power
Operating Temperature (Ta)
Storage Temperature (Tstg)
Channel Temperature (Tch)2
ESD Min. - Machine Model (MM)
ESD Min. - Human Body Model (HBM)
MSL Level
+8.0V
550 mA
-2.4V
2.8W
15 dBm
-55 to +85 ºC
-65 to +165 ºC
150 ºC
Class A
Class 1A
MSL3
Page 1 of 6
(1) Operation of this device above any one of these parameters
may cause permanent damage.
(2) Channel temperature directly affects a device’s MTTF.
Channel temperature should be kept as low as possible to
maximize lifetime
Electrical Characteristics (Ambient Temperature T = 25 oC)
Parameter
Frequency Range (f)
Small Signal Gain (S21)
Input Return Loss (S11)
Output Return Loss (S22)
Reverse Isolation (S12)
NF at Max Gain
P1dB
OIP3 at Pout = 8 dBm per Tone
Drain Bias Voltage (Vd1,2,3)
Gate Bias Voltage (Vg1,2,3)
Supply Current (Id1)
Supply Current (Id2)
Supply Current (Id3)
Units
GHz
dB
dB
dB
dB
dB
dB
dBm
VDC
VDC
mA
mA
mA
Min.
12.0
19.0
36.0
-2
Typ.
-
21.0
12.0
10.0
50.0
6.0
25.0
38.0
5
-1
75
75
150
Max.
16.0
8.0
125
125
250
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
P1042-QT
The XP1042-QT is a packaged driver amplifier that
operates over the 12.0-16.0 GHz frequency band. The
device provides 21 dB gain and 38 dBm Output Third
Order Intercept Point (OIP3) across the band and is
offered in an industry standard, fully molded 3x3mm
QFN package. The device includes on-chip ESD
protection structures and DC by-pass capacitors to
ease the implementation and volume assembly of the
packaged part. The device is manufactured in 0.5um
GaAs PHEMT device technology with BCB wafer
coating to enhance ruggedness and repeatability of
performance. The XP1042-QT is well suited for
Point-to-Point Radio, LMDS, SATCOM and VSAT
applications.
General Description
February 2010 - Rev 22-Feb-10
Power Amplifier Measurements
Page 2 of 6
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
P1042-QT
XP1042-QT: S-parameters (dB) vs. Freq (GHz),
VDD=5V, ID1=125mA, ID2=125mA, ID3=250mA
-20
-15
-10
-5
0
5
10
15
20
25
10 11 12 13 14 15 16 17 18
Freq (GHz)
S-parameter (dB)
S21
S11
S22
XP1042-QT: Power Out (dBm) vs. Power In (dBm),
VDD=5V, ID1=125mA, ID2=125mA, ID3=250mA
5
10
15
20
25
30
-15 -10 -5 0 5 10
Power In (dBm)
Power Out (dBm)
12.5 GHz
13 GHz
13.5 GHz
14 GHz
14.5 GHz
15 GHz
15.5 GHz
XP1042-QT: C/I3 (dBc) vs. Output Tone Power (per tone) dBm
10MHz tone separation VDD=5V, ID1=125mA, ID2=125mA, ID3=250mA
0
10
20
30
40
50
60
70
80
6 8 10 12 14 16 18 20
Output tone level per tone (dBm)
C/I3 (dBc)
12.5 GHz
13 GHz
13.5 GHz
14 GHz
14.5 GHz
15 GHz
15.5 GHz
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
February 2010 - Rev 22-Feb-10
MTTF
Page 3 of 6
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
P1042-QT
These numbers were calculated based on accelerated life test information and thermal model analysis received from
the fabricating foundry.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
February 2010 - Rev 22-Feb-10
XP1042-QT-0G00: MTTF hours vs Package Base Temperature
Vd1,2,3=5.0V;Id1=125mA,Id2=125mA,Id3=250mA
1.E+10
1.E+12
1.E+14
u
rs)
1.E+00
1.E+02
1.E+04
1.E+06
1.E+08
20 30 40 50 60 70 80 90 100 110 120
Packa
g
e Base Tem
p (
o
C
)
MTTF (hou
g p (
)
XP1042-QT-0G00: Tch(max) vs Package Base Temperature
Vd1,2,3=5.0V;Id1=125mA,Id2=125mA,Id3=250mA
120
140
160
180
200
(
o
C)
0
20
40
60
80
100
20 30 40 50 60 70 80 90 100 110 120
Package Base Temp (
o
C)
Tch max
XP1080-QK-0N00: Operating Power De-rating Curve (continuous)
Vd1,2,3=5V,Id1=125mA,Id2=125mA,Id3=250mA
1 5
2
2.5
3
s
(W)
0
0.5
1
1
.
5
25 50 75 100 125 150 175
Package Base Temp (
o
C)
Pdis
s
Page 4 of 6
Package Dimensions / Layout
Functional Block Diagram Pin Designations
Pin Number
1-2
3
4
5
6
7
8-9
10
11-12
13
14
15
16
Pin Name
nc
RF In
nc
Vg1
Vg2
Vg3
nc
RF Out
nc
Vd3
Vd2
Vd1
nc
Pin Function
Not Connected
RF Input
Not Connected
Gate 1 Bias
Gate 2 Bias
Gate 3 Bias
Not Connected
RF Output
Not Connected
Drain 3 Bias
Drain 2 Bias
Drain 1 Bias
Not Connected
Nominal Value
GND
GND
~ -1.0V
~ -0.8V
~ -1.0V
GND
GND
5.0V, 250 mA
5.0V, 125 mA
5.0V, 125 mA
GND
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
P1042-QT
1
2
3
4
16
15
14
13
12
11
10
9
5
6
7
8
RF In
Vg1 Vg3
RF Out
nc
nc
Vg2 nc
nc
nc
nc
nc Vd1 Vd2 Vd3
nc
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
February 2010 - Rev 22-Feb-10
Page 5 of 6
Recommended Layout
App Note [1] Biasing - As shown in the Pin Designations table, the device is operated by biasing VD1,2,3 at 5.0V with 125, 125, 250 mA respectively.
It is recommended to use active bias to keep the currents constant in order to maintain the best performance over temperature. Depending on the
supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with
a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current
and thus drain voltage. The typical gate voltage needed to do this is -1.0V. Make sure to sequence the applied voltage to ensure negative gate bias
is available before applying the positive drain supply.
App Note [2] Board Layout - As shown in the board layout, it is recommended to provide 100pF decoupling caps as close to the bias pins as
possible, with additional 10µF decoupling caps.
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
P1042-QT
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
February 2010 - Rev 22-Feb-10
Page 6 of 6
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
P1042-QT
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems
without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or
systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to
perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a
significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high
volume solder installation. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be
taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids
or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress.
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for
eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit
and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper
alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260°C
reflow) “Pb Free” processes.
Part Number for Ordering Description
XP1042-QT-0G00 Matte Tin plated RoHS compliant 3x3 16L QFN surface mount package in bulk quantity
XP1042-QT-0G0T Matte Tin plated RoHS compliant 3x3 16L QFN surface mount package in tape and reel
XP1042-QT-EV1 XP1042-QT evaluation board
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the
environment. For safety, observe the following procedures:
• Do not ingest.
• Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-
products are dangerous to the human body if inhaled, ingested, or swallowed.
• Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with
methods specified by applicable hazardous waste procedures.
Typical Reflow Profiles
Reflow Profile
Ramp Up Rate
Activation Time and Temperature
Time Above Melting Point
Max Peak Temperature
Time Within 5 ºC of Peak
Ramp Down Rate
SnPb
3-4 ºC/sec
60-120 sec @ 140-160 ºC
60-150 sec
240 ºC
10-20 sec
4-6 ºC/sec
Pb Free
3-4 ºC/sec
60-180 sec @ 170-200 ºC
60-150 sec
265 ºC
10-20 sec
4-6 ºC/sec
Factory Automation and Identification
Mimix
Designator
-QT
Package
Type
QFN (3x3mm)
P1 Component
Pitch
8mm
P0 Hole
Pitch
4mm
W Tape
Width
12mm
Number of
leads offered
16
Reel
Diameter
329mm (13in)
Units
per Reel
2000
Component Orientation: Parts are to be oriented with the PIN 1 closest to the tape's round sprocket holes on the tape’s trailing edge.
Note: Tape and Reel packaging is ordered with a -0G0T suffix. Package is available in 500 unit reels through designated sales channels.
Minimum order quantities should be discussed with your local sales representative.
Ordering Information
Caution: ESD Sensitive
Appropriate precautions in handling, packaging
and testing devices must be observed.
Proper ESD procedures should be followed when handling this device.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
February 2010 - Rev 22-Feb-10
