Document Number: 30259 For technical questions, contact: filmresistorsleaded@vishay.com www.vishay.com
Revision: 19-Oct-09 157
SR37
Surge Metal Film Leaded Resistor Vishay BCcomponents
PERFORMANCE
IEC
60115-1
CLAUSE
IEC
60068-2-xx
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR)
SR37
4.8 - Temperature
coefficient Between - 55 °C and + 155 °C ± 250 ppm/K
4.25.1 - Endurance at 70 °C
1000 h;
loaded with P70 or Umax.;
1.5 h ON; 0.5 h OFF
± (3 % R + 0.1 Ω)
4.24 78 (Cab) Damp heat,
steady state
56 days; 40 °C;
90 % to 95 % RH
loaded with 0.01 P70
± (3 % R + 0.1 Ω)
4.23 Climatic sequence
± (3 % R + 0.1 Ω)
4.23.2 2 (Ba) Dry heat 155 °C; 16 h dry heat
4.23.3 30 (Db) Damp heat
(accelerated)
24 h; 25 °C to 55 °C;
90 % to 100 % RH
1st cycle
4.23.4 1 (Aa) Cold - 55 °C; 2 h
4.23.6 30 (Db)
Damp heat,
(accelerated)
remaining cycles
5 days; 25 °C to 55 °C
90 % to 100 % RH
4.19 14 (Na) Rapid change of
temperature
30 min at LCT;
30 min at UCT;
LCT = - 55 °C;
UCT = 155 °C;
5 cycles
No visual damage
± (1 % R + 0.1 Ω)
4.26 - Active flammability
“Cheese-cloth test“
Steps of:
5/10/16/25/40 x P70 duration
5 min
No flaming of gauze cylinder
--
Passive flammability
“Needle-flame test“ Application of test flame for 20 s
No ignition of product
no ignition of under-layer
burning time less than 30 s
--
High voltage pulse
test
For R-value ≤ 4.7 kΩ, 10 kV;
1 nF; 50 x 12/min
(in accordance with
IEC 60065 14.1.a)
± 20 % R
4.16 Robustness of
terminations:
No damage
± (1 % R + 0.1 Ω)
4.16.2 21 (Ua1) Tensile all samples Load 10 N; 10 s
4.16.3 21 (Ub) Bending half number
of samples Load 5 N; 4 x 90°
4.16.4 21 (Uc) Torsion other half of
samples 3 x 360° in opposite direction
4.22 6 (Fc) Vibration
Frequency 10 Hz to 500 Hz;
displacement
1.5 mm or acceleration 10 g;
3 directions;
total 6 h (3 x 2 h)
± (1 % R + 0.1 Ω)
4.17 20 (Ta) Solderability
(after ageing)
2 s; 235 °C: Solder bath method;
SnPb40
3 s; 245 °C: Solder bath method;
SnAg3Cu0.5
Good tinning
(≥ 95 % covered);
no visible damage
4.18 20 (Tb) Resistance to
soldering heat
Thermal shock: 10 s; 260 °C;
3 mm from body ± (1 % R + 0.1 Ω)
4.29 45 (XA) Component solvent
resistance
Isopropyl alcohol or H2O
followed by brushing No visible damage
4.6.1.1 - Insulation resistance
U = 500 VDC
during 1 min,
V-block method
Rins min. 104 MΩ
4.7 - Voltage proof on
insulation
URMS = 700 V
during 1 min,
V-block method
No flashover or breakdown