NOTICE OF REVISION (NOR) 1. DATE (YYMMDD) 94-10-25 This revision described below has been authorized for the document listed. Form Approved OMB No. 0704-0188 Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washingtion Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLETED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM. b. ADDRESS (Street, City, State, Zip Code) 4. ORIGINATOR Defense Electronics Supply Center 1507 Wilmington Pike Dayton, OH 45444-5270 a. TYPED NAME (First, Middle Initial, Last) 9. TITLE OF DOCUMENT 2. PROCURING ACTIVITY NO. 3. DODAAC 5. CAGE CODE 6. NOR NO. 67268 5962-R284-94 7. CAGE CODE 8. DOCUMENT NO. 67268 5962-86845 11. ECP NO. 10. REVISION LETTER Microcircuits, Linear, High-Speed Voltage Comparator, Switching, Monolithic Silicon. a. CURRENT b. NEW A B 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES All 13. DESCRIPTION OF REVISION Sheet 1: Revisions ltr column; add "B". Revisions description column; add "Changes in accordance with NOR 5962-R284-94". Revisions date column; add "94-10-25". Revision level block; add "B". Rev status above sheet number 1and 2, add "B". Sheet 2: 1.3 Absolute maximum rating, Power dissipation (PD) test, delete "140 mW" and substitute "250 mW". Revision level block; add "B". 14. THIS SECTION FOR GOVERNMENT USE ONLY a. (X one) X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT c. TYPED NAME (First, Middle Initial, Last) DESC-ELDS Michael A. Frye d. TITLE e. SIGNATURE Chief, Custom Microelectronics Michael A. Frye 15a. ACTIVITY ACCOMPLISHING REVISION DESC-ELDS DD Form 1695, APR 92 f. DATE SIGNED (YYMMDD) b. REVISION COMPLETED (Signature) Marcia B. Kelleher Previous editions are obsolete 94-10-25 c. DATE SIGNED (YYMMDD) 94-10-25 DATE (YYMMDD) NOTICE OF REVISION (NOR) (See MIL-STD-480 for instructions) This revision described below has been authorized for the document listed. Form Approved OMB No. 0704-0188 92-10-08 Public reporting burden for this collection is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Information and Regulatory Affairs, Office of Management and Budget, Washington, DC 20503. 1. 2. ORIGINATOR NAME AND ADDRESS CAGE CODE 3. 67268 Defense Electronics Supply Center Dayton, Ohio 45444-5277 4. 5962-R314-92 CAGE CODE 5. 67268 6. TITLE OF DOCUMENT MICROCIRCUIT, LINEAR, HIGH SPEED VOLTAGE COMPARATOR, MONOLITHIC SILICON 7. NOR NO. DOCUMENT NO. 5962-86845 REVISION LETTER A (Current) 8. (New) ECP NO. 5962-86845ECP-1 9. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES All 10. DESCRIPTION OF REVISION Sheet 1: Revisions ltr column; add "A". Revisions description column; add "Changes in accordance with NOR 5962-R314-92". Revisions date column; add "92-10-08". Revision level block; add "A". Rev status of sheets; For sheet 4, add "A". Sheet 4: TABLE I, power supply rejection ratio test with condition of "+4.6 V V+ +5.4 V", under minimum limits column, delete 60 dB and substitute 54 dB. TABLE I, output high voltage test, with condition of "V+ 4.6 V, IOUT = 1.0 mA", under minimum limits column, delete 3.0 V and substitute 2.7 V. Revision level block, add "A". 11. THIS SECTION FOR GOVERNMENT USE ONLY a. CHECK ONE eXf EXISTING DOCUMENT SUPPLEMENTED e f REVISED DOCUMENT MUST BE e f CUSTODIAN OF MASTER DOCUMENT BY THIS NOR MAY BE USED IN RECEIVED BEFORE MANUFACTURER SHALL MAKE ABOVE REVISION AND MANUFACTURE. MAY INCORPORATE THIS CHANGE. FURNISH REVISED DOCUMENT TO: b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENT DESC-ECS 12. ACTIVITY ACCOMPLISHING REVISION DESC-ECS DD Form 1695, JUL 88 SIGNATURE AND TITLE DATE (YYMMDD) Michael A. Frye BRANCH CHIEF REVISION COMPLETED (Signature) Rick C. Officer 92-10-08 DATE (YYMMDD) 92-10-08 Previous editions are obsolete. REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV STATUS OF PAGES Defense Electronics Supply Center Dayton, Ohio Original date of drawing: 8 Oct 87 REV PAGES 1 2 3 4 5 PREPARED BY Donald R. Osborne 6 7 9 MILITARY DRAWING This drawing is available for use by all Departments and Agencies of the Department of Defense CHECKED BY D A DiCenzio APPROVED BY Robert P. Evans TITLE: MICROCIRCUIT, LINEAR, HIGH-SPEED VOLTAGE COMPARATOR, MONOLITHIC SILICON CODE IDENT. NO. SIZE A 67268 DWG NO. 5962-86845 REVISION LEVEL AMSC N/A 8 A SHEET 1 OF 9 5962-E148 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. DESC FORM 193 MAY 86 1. SCOPE 1.1 Scope. This drawing describes device requirements for class B microcircuits in accordance with 1.2.1 of MIL-STD-883, "Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices". 1.2 Part number. The complete part number shall be as shown in the following example: 5962-86845 Drawing number 01 I Device type (1.2.1) X Case outline (1.2.2) Lead finish per MIL-M-38510 1.2.1 Device type. The device type shall identify the circuit function as follows: Device type Generic number 01 Circuit LT1016 High speed comparator 1.2.2 Case outlines. The case outlines shall be as designated in appendix C of MIL-M-38510, and as follows: Outline letter I P Case outline A-2 (10-lead), metal can D-4 (8-lead, 1/4" x 3/8"), dual-in-line package 1.3 Absolute maximum ratings. Positive supply voltage - - - - - - - - - - - - - - - - - - - - - - - - Negative supply voltage - - - - - - - - - - - - - - - - - - - - - - - Differential input voltage - - - - - - - - - - - - - - - - - - - - - - - Input voltage (either input) - - - - - - - - - - - - - - - - - - - - - Latch input voltage - - - - - - - - - - - - - - - - - - - - - - - - - - - Output current (continuous) - - - - - - - - - - - - - - - - - - - - Storage temperature range- - - - - - - - - - - - - - - - - - - - - Lead temperature (soldering, 10 seconds) - - - - - - - - - - Maximum power dissipation (PD) - - - - - - - - - - - - - - - - Thermal resistance, junction-to-case (JC): Case I - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Case P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Junction temperature (TJ)- - - - - - - - - - - - - - - - - - - - - - - +7.0 V dc -7.0 V dc 5.0 V dc 7.0 V dc 7.0 V dc 20 mA -65(C to +150(C +300(C 140 mW 60(C/W 50(C/W +150(C 1.4 Recommended operating conditions. Ambient operating temperature range (TA) - - - - - - - - - - -55(C to +125(C SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 2 2. APPLICABLE DOCUMENTS 2.1 Government specification and standard. Unless otherwise specified, the following specification and standard, of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified herein. SPECIFICATION MILITARY MIL-M-38510 - Microcircuits, General Specification for. STANDARD MILITARY MIL-STD-883 - Test Methods and Procedures for Microelectronics. (Copies of the specification and standard required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with 1.2.1 of MIL-STD-883, "Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices" and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-M-38510 and herein. 3.2.1 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.2 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.3 Electrical performance characteristics. Unless otherwise specified, the electrical performance characteristics are as specified in table I and apply over the full case operating temperature range. 3.4 Marking. Marking shall be in accordance with MIL-STD-883 (see 3.1 herein). The part shall be marked with the part number listed in 1.2 herein. In addition, the manufacturer's part number may also be marked as listed in 6.4 herein. 3.5 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in 6.4. The certificate of compliance submitted to DESC-ECS prior to listing as an approved source of supply shall state that the manufacturer's product meets the requirements of MIL-STD-883 (see 3.1 herein) and the requirements herein. 3.6 Certificate of conformance. A certificate of conformance as required in MIL-STD-883 (see 3.1 herein) shall be provided with each lot of microcircuits delivered to this drawing. 3.7 Notification of change. Notification of change to DESC-ECS shall be required in accordance with MIL-STD-883 (see 3.1 herein). SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 3 TABLE I. Electrical performance characteristics. Test Conditions 1/ -55(C TA +125(C unless otherwise specified Symbol Group A subgroups Limits Min Input offset voltage 2/ VOS RS 1006, TA = +25(C RS 1006 Input offset current 2/ Input bias current Input voltage range IOS IB TA = +25(C TA = +25(C VINR Unit Max 1 2.0 mV 2, 3 3.0 mV 1 1.0 )A 2, 3 1.3 )A 1 10 )A 2, 3 13 )A 1, 2, 3 -3.75 +3.5 V Single +5.0 V supply 1, 2, 3 +1.25 +3.5 V Common-mode rejection ratio CMRR -3.75 V VCM +3.5 V 1, 2, 3 80 dB Power supply rejection ratio PSRR +4.6 V V+ +5.4 V 1, 2, 3 60 dB -7.0 V V- -2.0 V 1, 2, 3 80 dB 4 1400 V/V 1, 2, 3 3.0 V 2.4 V Small signal voltage gain AV 1.0 V VOUT 2.0 V, TA = +25(C Output high voltage VOH V+ +4.6 V, IOUT = 1.0 mA IOUT = 10 mA Output low voltage VOL ISINK = 4.0 mA 1, 2, 3 0.5 V See footnotes at end of table. SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 4 TABLE I. Electrical performance characteristics - Continued. Test Conditions 1/ -55(C TA +125(C unless otherwise specified Symbol Group A subgroups Limits Min Unit Max Positive supply current I+ 1, 2, 3 35 mA Negative supply current I- 1, 2, 3 5.0 mA Latch pin input high voltage VIH 1, 2, 3 Latch pin input low voltage VIL 1, 2, 3 0.8 V Latch pin current IIL VLATCH = 0 V 1, 2, 3 500 )A Propagation delay time tPD VIN = 100 mV, TA = +25(C 4/ 0D = 5.0 mV 9 14 ns 0D = 20 mV 9 12 ns 0D = 5.0 mV 10, 11 16 ns 0D = 20 mV 10, 11 15 ns 9, 10, 11 5.0 ns VIN = 100 mV 4/ Differential propagation delay tPD VIN = 100 mV, 0D = 5.0 mV 4/ 2.0 V 1/ V+ = 5.0 V, V- = 5.0 V, VOUT(Q) = 1.4 V and VLATCH = 0 V, unless otherwise specified. 2/ Input offset voltage is defined as the average of the two voltages measured by forcing first one output, then the other to 1.4 V. Input offset current is defined the same way. 3/ Input bias current is defined as the average of the two input currents. 4/ Propagation delay time is measured with the overdrive added to actual VOS. Parameters are guaranteed by design, characterization, or correlation to other tested parameters. SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 5 FIGURE 1. Logic diagram and terminal connections. SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 6 3.8 Verification and review. DESC, DESC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with section 4 of MIL-M-38510 to the extent specified in MIL-STD-883 (see 3.1 herein). 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.5 herein). (2) TA = +125(C, minimum. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.5 herein). (2) TA = +125(C, minimum. (3) Test duration: 1,000 hours, except as permitted by appendix B of MIL-M-38510 and method 1005 of MIL-STD-883. SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 7 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (per method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) 1*, 2, 3, 4 Group A test requirements (method 5005) 1, 2, 3, 4, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1 *PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-M-38510. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-38510, the device specified herein will be inactivated and will not be used for new design. The QPL-38510 product shall be the preferred item for all applications. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Comments. Comments on this drawing should be directed to DESC-ECS, Dayton, Ohio 45444, or telephone 513-296-5375. SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 8 6.4 Approved source of supply. An approved source of supply is listed herein. Additional sources will be added as they become available. The vendor listed herein has agreed to this drawing and a certificate of compliance (see 3.5) has been submitted to DESC-ECS. Military drawing part number Vendor CAGE number Vendor similar part number 1/ 5962-8684501IX 64155 LT1016MH/883B 5962-8684501PX 64155 LT1016MJ8/883B 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number Vendor name and address 64155 Linear Technology Corporation 1630 McCarthy Boulevard Milpitas, CA 95035-7487 SIZE MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A FEB 87 DWG NO. 5962-86845 A REV PAGE 9