Production March 2003 (R) P1818/19/20/21/22 Low Power Mobile VGA EMI Reduction IC Features * * * * * FCC approved method of EMI attenuation Provides up to 15 dB EMI reduction Generates a low EMI spread spectrum clock and a non-spread reference clock of the input frequency Optimized for frequency range from 10 MHz to 160 MHz P1818: 10 to 20 MHz P1819: 20 to 40 MHz P1820: 40 to 80 MHz P1821: 10 to 40 MHz P1822: 80 to 160 MHz Internal loop filter minimizes external components and board space * * * * * * * * * * Selectable spread options: Down Spread and Center Spread Low inherent cycle-to-cycle jitter Eight spread % selections: +/-0.625% to -3.5% 3.3V operating voltage CMOS/TTL compatible inputs and outputs Low power CMOS design Supports notebook VGA and other LCD timing controller applications Power down function for mobile application Products are available for industrial temperature range. Available in 8-pin SOIC and TSSOP Product Description The P18xx is a versatile spread spectrum frequency modulator designed specifically for a wide range of input clock frequencies from 10 to 160 MHz (see Input Frequency and Modulation Rate Selections). The P18xx can generate an EMI reduced clock from crystal, ceramic resonator, or system clock. The P18xx-A to P18xx-H offer various combinations of spread options and percentage deviations (see Spread Deviation Selections). These combinations include Down Spread, Center Spread and percentage deviation range from 0.625% to -3.50%. The P18xx reduces electromagnetic interference (EMI) at the clock source, allowing a system wide EMI reduction for all the down stream clocks and data dependent signals. The P18xx allows significant system cost savings by reducing the number of circuit board layers, ferrite beads, shielding, and other passive components that are traditionally required to pass EMI regulations. The P18xx modulates the output of a single PLL in order to "spread" the bandwidth of a synthesized clock, thereby decreasing the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most clock generators. Lowering EMI by increasing a signal's bandwidth is called "spread spectrum clock generation". The P18xx uses the most efficient and optimized modulation profile approved by the FCC and is implemented by using a proprietary all-digital method. Applications The P18xx is targeted toward EMI management for memory and LVDS interfaces in mobile graphic chipsets and high-speed digital applications such as PC peripheral devices, consumer electronics, and embedded controller systems. Alliance Semiconductor 2575 Augustine Drive * Santa Clara, CA 95054 * Tel: 408.855.4900 * Fax: 408.855.4999 * www.alsc.com Notice: The information in this document is subject to change without notice. P1818/19/20/21/22 (R) Pin Diagrams X IN 1 8 XOUT 2 7 VDD 6 PD# 5 REF X IN 1 8 XOUT VSS 2 7 VDD D_C 3 6 PD# 5 REF VSS SRS M odO ut M odO ut 3 4 4 P 1 8 1 8 A /B /C /D P 1 8 1 9 A /B /C /D P 1 8 2 0 A /B /C /D P 1 8 1 8 E /F /G /H P 1 8 1 9 E /F /G /H P 1 8 2 0 E /F /G /H X IN 1 8 XOUT 2 7 VDD SRS 3 6 FRS M odO ut 4 5 REF X IN 1 8 MRS VSS 2 7 VDD SRS 3 6 SSON# 5 SR0 VSS M odO ut 4 P 1 8 2 1 A /B /C /D P1822A Block Diagram VDD D_C PD# MRS FRS SRS PLL Modulation XIN Crystal Oscillator Frequency Divider XOUT Feedback Divider Phase Detector Loop Filter VCO Output Divider ModOUT REF P1818/19/20/21/22 Block Diagram VSS March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 2 of 8 P1818/19/20/21/22 (R) Input Frequency and Modulation Rate Part number Input frequency range Output frequency range Modulation rate P1818 10 MHz to 20 MHz 10 MHz to 20 MHz Input frequency / 256 P1819 20 MHz to 40 MHz 20 MHz to 40 MHz Input frequency / 512 P1820 40 MHz to 80 MHz 40 MHz to 80 MHz Input frequency / 2048 FRS=0 10 MHz to 20 MHz 10 MHz to 20 MHz Input frequency / 256 FRS=1 20 MHz to 40 MHz 20 MHz to 40 MHz Input frequency / 512 80 MHz to 160 MHz 80 MHz to 160 MHz Input frequency / 3584 P1821 P1822 Spread Deviation Selections Part number1 SRS SR0 D_C Spread deviation P18182/19/20/21A N/A N/A N/A N/A N/A N/A N/A N/A P1818/19/20E 0 1 0 1 0 1 0 1 N/A N/A P1818/19/20F N/A N/A P1818/19/20G N/A N/A P18182/19/20H N/A N/A 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 N/A -2.50% (Down) -3.50% (Down) -1.25% (Down) -1.75% (Down) +/-1.25% (Center) +/-1.75% (Center) +/-0.625% (Center) +/-0.875% (Center) -1.25% (Down) +/-0.625% (Center) -2.5% (Down) +/-1.25% (Center) -1.75% (Down) +/-0.875% (Center) -3.5% (Down) +/-1.75% (Center) -1.25% (Down) -2.50% (Down) -1.75% (Down) -3.50% (Down) +/-0.625% (Center) +/-1.25% (Center) +/-0.875% (Center) +/-1.75% (Center) P1818/19/20/21B P1818/19/20/21C P1818/19/20/21D P1822A P1822B N/A 1. A through H represents various combinations of spread deviations, options, and modulation rates. 2. Refer to Frequency vs. Deviation (P1818A and P1818H). March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 3 of 8 P1818/19/20/21/22 (R) Frequency vs. Deviation (P1818A and P1818H) Deviation in P1818A Deviation in P1818H Frequency SRS = 1 SRS = 0 D_C = 1 D_C = 0 10 MHz -4.4% -3.3% -4.4% 2.2% 15 MHz -1.8% -1.26% -1.8% 0.9% 20 MHz -0.8% -0.6% -0.8% 0.4% Pin Description Pin number Name Type 1 XIN I Connect to externally generated clock signal or crystal. 2 VSS P Ground Connection. Connect to system ground. 3 SRS I Spread Range Select. Digital logic input used to select frequency deviation (see Spread Deviation Selections). This pin has an internal pullup resistor. 31 D_C I Digital logic input used to select Down (LOW) or Center (HIGH) Spread Options (see Spread Deviation Selections). This pin has an internal pull-up resistor. 4 ModOut O Spread Spectrum clock output (see Input Frequency and Modulation Rate Selections and Spread Deviation Selections). 5 REF O Non-modulated reference output clock of the input frequency. 5/61 FRS I Frequency Range Select. Digital logic input used to select input frequency range (see Input Frequency and Modulation Rate Selections). This pin has an internal pull-up resistor. 61 PD# I Power-Down control pin. Pull LOW to enable Power-Down mode. This pin has an internal pull-up resistor. 7 VDD P Connect to +3.3V 8 XOUT I Connect to crystal. No connect if externally generated clock signal is used. 81 MRS I Modulation Rate Select. Digital logic input used to select Modulation Rate (see Spread Deviation Selections). This pin has an internal pullup resistor. Description 1. Please refer to Figure 1 for pin assignment. March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 4 of 8 P1818/19/20/21/22 (R) Absolute Maximum Ratings Symbol Parameter VDD, VIN TSTG TA Rating Unit Voltage on any pin with respect to GND -0.5 to +7.0 V Storage temperature -65 to +125 C 0 to +70 C Operating temperature DC Electrical Characteristics 3.3 V, 25 C Symbol Parameter Min Typ Max Unit VIL Input low voltage GND - 0.3 - 0.8 V VIH Input high voltage 2.00 - VDD + 0.3 V IIL Input low current (inputs D_C, PD#, MRS, FRS, SRS) -60.0 - -20.00 A IIH Input high current - - 1.00 A IXOL XOUT output low current (@ 0.4 V, VDD = 3.3 V) 2.00 - 12.00 mA IXOH XOUT output high current (@ 2.5 V, VDD = 3.3 V) - - 12.00 mA VOL Output low voltage (VDD=3.3 V, IOL = 20 mA) - - 0.4 V VOH Output high voltage (VDD=3.3 V, IOH = 20 mA) - - 2.8 V IDD Static supply current Standby mode - 4.5 - mA ICC Dynamic supply current Normal mode (3.3 V and 25 pF probe loading) 7.1 fIN-min - 26.9 fIN-max mA VDD Operating voltage - 3.3 - V tON Power up time (first locked clock cycle after power up) - 0.18 - mS ZOUT Clock output impedance - 50 - March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 5 of 8 P1818/19/20/21/22 (R) AC Electrical Characteristics 3.3 V, 25 C Symbol Min Typ Max Unit Input frequency 10 - 160 MHz fOUT Output frequency 10 - 160 MHz tLH1 Output rise time (measured at 0.8 V to 2.0 V) - 0.66 - ns tHL1 Output fall time (measured at 2.0 V to 0.8 V) - 0.65 - ns tJC Jitter (cycle to cycle) at 20 MHz -200 - 200 ps tD Output duty cycle 45 50 55 % fIN Parameter 1. tLH and tHL are measured into a capacitive load of 15 pF March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 6 of 8 P1818/19/20/21/22 (R) Mechanical Package Outline (8-Pin SOIC) Inches Millimeters Symbol C L P18xxx LOT NUMBER YYWW H E a Min Nor Max Min Nor Max A 0.057 0.064 0.071 1.45 1.63 1.80 A1 0.004 0.007 0.010 0.10 0.18 0.25 A2 0.053 0.061 0.069 1.35 1.55 1.75 B 0.012 0.016 0.020 0.31 0.41 0.51 C 0.004 0.006 0.01 0.10 0.15 0.25 D 0.186 0.194 0.202 4.72 4.92 5.12 E 0.148 0.156 0.164 3.75 3.95 4.15 D e A2 B e A 0.050 BSC 1.27 BSC H 0.224 0.236 0.248 5.70 6.00 6.30 L 0.012 0.020 0.028 0.30 0.50 0.70 a 0 5 8 0 5 8 A1 Note: Controlling dimensions are millimeters. SOIC: 0.074 grams unit weight. Mechanical Package Outline (8-Pin TSSOP) Inches Millimeters Symbol Min Nor Max Min Nor Max A - - 0.047 - - 1.10 A1 0.002 - 0.006 0.05 - 0.15 A2 0.031 0.039 0.041 0.80 1.00 1.05 B 0.007 - 0.012 0.19 - 0.30 C 0.004 - 0.008 0.09 - 0.20 D 0.114 0.118 0.122 2.90 3.00 3.10 E 0.169 0.173 0.177 4.30 4.40 4.50 C P 18xxx Lot # YYWW L H E a D A2 B e A1 A e 0.026 BSC 0.65 BSC H 0.244 0.252 0.260 6.20 6.40 6.60 L 0.018 0.024 0.030 0.45 0.60 0.75 a 0 - 8 0 - 8 Note: Controlling dimensions are millimeters. TSSOP: 0.034 grams unit weight. March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 7 of 8 P1818/19/20/21/22 (R) Ordering Information X 18XX X -08 XX 1 2 3 4 5 1. Flow prefix: I = industrial temperature range (-40 C to 85 C) P = commercial temperature range (0 C to 70 C) 2. Device number 3. Deviation (%) and spread option identifier 4. Device pin count 5. Package identifier: ST = SOIC in tube SR = SOIC in tape and reel TT = TSSOP in tube TR = TSSOP in tape and reel Example: Ordering number Marking Input frequency (MHz) Frequency deviation (%) Package type P1818A-08ST P1818A 10 - 20 -2.5, -3.5 8 PIN SOIC, TUBE P1818A-08SR P1818A 10 - 20 -2.5, -3.5 8 PIN SOIC, TAPE & REEL P1818A-08TT P1818A 10 - 20 -2.5, -3.5 8 PIN TSSOP, TUBE P1818A-08TR P1818A 10 - 20 -2.5, -3.5 8 PIN TSSOP, TAPE & REEL Qty. / reel Temp1 0C to 70C 2,500 0C to 70C 0C to 70C 2,500 0C to 70C 1. Products are available for industrial temperature range operation. Please contact factory for more information. Licensed under U.S. patent numbers 5,488,627 and 5,631,920. (c) Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights, mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use. March 2003 Low Power Mobile VGA EMI Reduction IC Notice: The information in this document is subject to change without notice. 8 of 8