Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. 74VHC123A Dual Retriggerable Monostable Multivibrator tm Features General Description High Speed: tPD = 8.1ns (Typ.) at TA = 25C Low Power Dissipation: ICC = 4A (Max) at TA = 25C The VHC123A is an advanced high speed CMOS Monostable Multivibrator fabricated with silicon gate CMOS technology. It achieves the high speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. Each multivibrator features both a negative, A, and a positive, B, transition triggered input, either of which can be used as an inhibit input. Also included is a clear input that when taken low resets the one-shot. The VHC123A can be triggered on the positive transition of the clear while A is held low and B is held high. The output pulse width is determined by the equation: PW = (Rx)(Cx); where PW is in seconds, R is in ohms, and C is in farads. Active State: ICC = 600A (Max.) at TA = 25C High Noise Immunity: VNIH = VNIL = 28% VCC (Min.) Power down protection is provided on all inputs Pin and function compatible with 74HC123A Limits for Rx and Cx are: External capacitor, Cx : No limit External resistors, Rx: VCC = 2.0V, 5 k min VCC > 3.0V, 1 k min An input protection circuit ensures that 0 to 7V can be applied to the input pins without regard to the supply voltage. This device can be used to interface 5V to 3V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages. Ordering Information Order Number 74VHC123AM 74VHC123ASJ 74VHC123AMTC Package Number Package Description M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MTC16 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Surface mount packages are also available on Tape and Reel. Specify by appending the suffix letter "X" to the ordering number. (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 74VHC123A Dual Retriggerable Monostable Multivibrator May 2007 Logic Symbol IEEE/IEC Pin Description Pin Names Description A Trigger Inputs (Negative Edge) B Trigger Inputs (Positive Edge) CLR Reset Inputs Cx External Capacitor Rx External Resistor Q, Q Outputs Truth Table Inputs A Outputs B CLR H H X L H L H H X H L H L Q Q Output Enable H L H X X Function Inhibit Inhibit Output Enable Output Enable L L H Reset H = HIGH Voltage Level L = LOW Voltage Level = HIGH-to-LOW Transition = LOW-to-HIGH Transition X = Don't Care (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 2 74VHC123A Dual Retriggerable Monostable Multivibrator Connection Diagram Note A: Cx, Rx, Dx are external Capacitor, Resistor, and Diode, respectively. Note B: External clamping diode, Dx; External capacitor is charged to VCC level in the wait state, i.e. when no trigger is applied. If the supply voltage is turned off, Cx discharges mainly through the internal (parasitic) diode. If Cx is sufficiently large and VCC drops rapidly, there will be some possibility of damaging the IC through in rush current or latch-up. If the capacitance of the supply voltage filter is large enough and VCC drops slowly, the in rush current is automatically limited and damage to the IC is avoided. The maximum value of forward current through the parasitic diode is 20mA. In the case of a large Cx, the limit of fall time of the supply voltage is determined as follows: tf (VCC -0.7) Cx / 20mA (tf is the time between the supply voltage turn off and the supply voltage reaching 0.4 VCC) In the event a system does not satisfy the above condition, an external clamping diode (Dx) is needed to protect the IC from rush current. (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 3 74VHC123A Dual Retriggerable Monostable Multivibrator Block Diagrams 74VHC123A Dual Retriggerable Monostable Multivibrator System Diagram Timing Chart (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 4 the output Q goes LOW and C2 stops its operation. That means, after triggering, when the voltage level of the Rx/Cx node reaches VrefH, the IC returns to its MONOSTABLE state. 1. Stand-by State The external capacitor (Cx) is fully charged to VCC in the Stand-by State. That means, before triggering, the QP and QN transistors which are connected to the Rx/Cx node are in the off state. Two comparators that relate to the timing of the output pulse, and two reference voltage supplies turn off. The total supply current is only leakage current. With large values of Cx and Rx, and ignoring the discharge time of the capacitor and internal delays of the IC, the width of the output pulse, tW (OUT), is as follows: tW (OUT) = 1.0 Cx Rx 2. Trigger Operation Trigger operation is effective in any of the following three cases. First, the condition where the A input is LOW, and B input has a rising signal; second, where the B input is HIGH, and the A input has a falling signal; and third, where the A input is LOW and the B input is HIGH, and the CLR input has a rising signal. 3. Retrigger operation (74VHC123A) When a new trigger is applied to either input A or B while in the MONOSTABLE state, it is effective only if the IC is charging Cx. The voltage level of the Rx/Cx node then falls to VrefL level again. Therefore the Q output stays HIGH if the next trigger comes in before the time period set by Cx and Rx. After a trigger becomes effective, comparators C1 and C2 start operating, and QN is turned on. The external capacitor discharges through QN. The voltage level at the Rx/Cx node drops. If the Rx/Cx voltage level falls to the internal reference voltage VrefL, the output of C1 becomes LOW. The flip-flop is then reset and QN turns off. At that moment C1 stops but C2 continues operating. If the new trigger is very close to a previous trigger, such as an occurrence during the discharge cycle, it will have no effect. The minimum time for a trigger to be effective 2nd trigger, tRR (Min), depends on VCC and Cx. 4. Reset Operation After QN turns off, the voltage at the Rx /Cx node starts rising at a rate determined by the time constant of external capacitor Cx and resistor Rx. In normal operation, the CLR input is held HIGH. If CLR is LOW, a trigger has no affect because the Q output is held LOW and the trigger control F/F is reset. Also, Qp turns on and Cx is charged rapidly to VCC. Upon triggering, output Q becomes HIGH, following some delay time of the internal F/F and gates. It stays HIGH even if the voltage of Rx/Cx changes from falling to rising. When Rx/Cx reaches the internal reference voltage VrefH, the output of C2 becomes LOW, (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 This means if CLR is set LOW, the IC goes into a wait state. www.fairchildsemi.com 5 74VHC123A Dual Retriggerable Monostable Multivibrator Functional Description Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Rating VCC Supply Voltage -0.5V to +7.0V VIN DC Input Voltage -0.5V to +7.0V VOUT DC Output Voltage -0.5V to VCC + 0.5V IIK Input Diode Current -20mA IOK Output Diode Current 20mA IOUT DC Output Current 25mA ICC DC VCC / GND Current 50mA TSTG TL Storage Temperature -65C to +150C Lead Temperature (Soldering, 10 seconds) 260C Recommended Operating Conditions(1) The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter VCC Supply Voltage VIN Input Voltage VOUT Output Voltage TOPR Operating Temperature tr , tf Rating 2.0V to +5.5V 0V to +5.5V 0V to VCC -40C to +85C Input Rise and Fall Time (CLR only) VCC = 3.3V 0.3V 0ns/V 100ns/V VCC = 5.0V 0.5V 0ns/V 20ns/V No Limitation(2) F External Capacitor, Cx >5k(2) (VCC = 2.0V) External Resistor, Rx >1k(2) (VCC > 3.0V) Notes: 1. Unused inputs must be held HIGH or LOW. They may not float. 2. The maximum allowable values of Cx and Rx are a function of the leakage of capacitor Cx, the leakage of the device, and leakage due to board layout and surface resistance. Susceptibility to externally induced noise signals may occur for Rx > 1M. (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 6 74VHC123A Dual Retriggerable Monostable Multivibrator Absolute Maximum Ratings TA = 25C Symbol Parameter VIH HIGH Level Input Voltage VIL LOW Level Input Voltage VOH HIGH Level Output Voltage VCC (V) Conditions Min. 2.0 1.50 3.0-5.5 0.7 x VCC 3.0 LOW Level Output Voltage Min. IOH = -50A 2.0 1.9 2.9 3.0 2.9 4.4 4.5 4.4 IOH = -4mA 2.58 2.48 4.5 IOH = -8mA 3.94 3.80 3.0 VIN = VIH or VIL IOL = 50A 4.5 3.0 4.5 V 0.0 0.1 0.1 0.0 0.1 0.1 0.0 IOL = 4mA IOL = 8mA V 0.3 x VCC 1.9 3.0 2.0 Units V 0.50 0.3 x VCC VIN = VIH or VIL Max. 0.7 x VCC 0.50 3.0-5.5 2.0 Max. 1.50 2.0 4.5 VOL Typ. TA = -40 to 85C 0.1 0.1 0.36 0.44 V 0.36 0.44 0-5.5 VIN = 5.5V or GND 0.1 1.0 A Rx/Cx Terminal Off-State Current 5.5 VIN = VCC or GND 0.25 2.50 A ICC Quiescent Supply Current 5.5 VIN = VCC or GND 4.0 40.0 A ICC Active--State(3) Supply Current 3.0 VIN = VCC or GND, Rx/Cx = 0.5 VCC 160 250 280 A 380 500 650 560 750 975 IIN Input Leakage Current IIN 4.5 5.5 Note: 3. Per circuit. (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 7 74VHC123A Dual Retriggerable Monostable Multivibrator DC Electrical Characteristics TA = -40C to +85C TA = 25C Symbol Parameter tPLH, tPHL Propagation Delay Time (A, B-Q, Q) VCC (V) 3.3 0.3 5.0 0.5 tPLH, tPHL Propagation Delay Time (CLR Trigger--Q, Q) 3.3 0.3 5.0 0.5 tPLH, tPHL Propagation Delay Time (CLR--Q, Q) 3.3 0.3 5.0 0.5 tWOUT Output Pulse Width 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 3.3 0.3 5.0 0.5 tWOUT Conditions Min. Typ. Max. Min. Max. Units CL = 15 pF 13.4 20.6 1.0 24.0 CL = 50 pF 15.9 24.1 1.0 27.5 CL = 15 pF 8.1 12.0 1.0 14.0 CL = 50 pF 9.6 14.0 1.0 16.0 CL = 15 pF 14.5 22.4 1.0 26.0 CL = 50 pF 17.0 25.9 1.0 29.5 CL = 15 pF 8.7 12.9 1.0 15.0 CL = 50 pF 10.2 14.9 1.0 17.0 CL = 15 pF 10.3 15.8 1.0 18.5 CL = 50 pF 12.8 19.3 1.0 22.0 CL = 15 pF 6.3 9.4 1.0 11.0 CL = 50 pF 7.8 11.4 1.0 13.0 CL = 50pF, Cx = 28pF, Rx = 2k 160 240 300 133 200 CL = 50pF, Cx = 0.01F, Rx = 10k 90 100 110 90 110 90 100 110 90 110 CL = 50pF, Cx = 0.1F, Rx = 1k 0.9 1.0 1.1 0.9 1.1 0.9 1.0 1.1 0.9 1.1 Output Pulse Width Error Between Circuits (In same Package) CIN Input Capacitance VCC = Open Power Dissipation Capacitance (5) 4 73 ns ns ns ns ns ns 240 1 CPD ns s ms % 10 10 pF pF Notes: 4. Refer to Timing Chart. 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr.) = CPD * VCC * fIN+ ICC1 * Duty / 100 + ICC / 2 (per Circuit) ICC1: Active Supply Current Duty: % (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 8 74VHC123A Dual Retriggerable Monostable Multivibrator AC Electrical Characteristics(4) TA = 25C Symbol tW(L), tW(H) tW(L) tRR Parameter VCC (V) Conditions Min. Typ. Max. TA = -40C to +85C Min. Minimum Trigger 3.3 5.0 5.0 Pulse Width 5.0 5.0 5.0 Minimum Clear Pulse Width 3.3 5.0 5.0 5.0 5.0 5.0 Minimum Retrigger Time 3.3 0.3 5.0 0.5 3.3 5.0 Rx = 1k, CX = 100pF 60 Rx = 1k, CX = 0.01F 1.5 Max. Units ns ns ns 39 s 1.2 Note: 6. Refer to Timing Chart. (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 9 74VHC123A Dual Retriggerable Monostable Multivibrator AC Operating Requirement(6) twout*Cx Characteristics (Typ.) tRR*VCC Characteristics (Typ.) Output Pulse Width Constant K-Supply Voltage (Typ.) Input Equivalent Circuit (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 10 74VHC123A Dual Retriggerable Monostable Multivibrator Device Characteristics 74VHC123A Dual Retriggerable Monostable Multivibrator Physical Dimensions Dimensions are in millimeters unless otherwise noted. Figure 1. 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package Number M16A (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 11 74VHC123A Dual Retriggerable Monostable Multivibrator Physical Dimensions (Continued) Dimensions are in millimeters unless otherwise noted. Figure 2. 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M16D (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 12 5.000.10 4.55 5.90 4.45 7.35 0.65 4.40.1 1.45 5.00 0.11 12 MTC16rev4 Figure 3. 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC16 (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 13 74VHC123A Dual Retriggerable Monostable Multivibrator Physical Dimensions (Continued) Dimensions are in millimeters unless otherwise noted. (R) ACEx Across the board. Around the world.TM ActiveArrayTM BottomlessTM Build it NowTM CoolFETTM CROSSVOLTTM CTLTM Current Transfer LogicTM DOMETM 2 E CMOSTM (R) EcoSPARK EnSignaTM FACT Quiet SeriesTM (R) FACT (R) FAST FASTrTM FPSTM (R) FRFET GlobalOptoisolatorTM GTOTM HiSeCTM i-LoTM ImpliedDisconnectTM IntelliMAXTM ISOPLANARTM MICROCOUPLERTM MicroPakTM MICROWIRETM Motion-SPMTM MSXTM MSXProTM OCXTM OCXProTM (R) OPTOLOGIC (R) OPTOPLANAR PACMANTM PDP-SPMTM POPTM (R) Power220 (R) Power247 PowerEdgeTM PowerSaverTM Power-SPMTM (R) PowerTrench Programmable Active DroopTM (R) QFET QSTM QT OptoelectronicsTM Quiet SeriesTM RapidConfigureTM RapidConnectTM ScalarPumpTM SMART STARTTM (R) SPM STEALTHTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SyncFETTM TCMTM (R) The Power Franchise TinyBoostTM TinyBuckTM (R) TinyLogic TINYOPTOTM TinyPowerTM TinyWireTM TruTranslationTM SerDesTM (R) UHC UniFETTM VCXTM WireTM TM DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Definition Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. Rev. I26 (c)1993 Fairchild Semiconductor Corporation 74VHC123A Rev. 1.2 www.fairchildsemi.com 14 74VHC123A Dual Retriggerable Monostable Multivibrator TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com