© Semiconductor Components Industries, LLC, 2016
July, 2016 − Rev. 9 1Publication Order Number:
NLU2G17/D
NLU2G17
Dual Non-Inverting
Schmitt-Trigger Buffer
The NLU2G17 MiniGatet is an advanced high−speed CMOS dual
non−inverting Schmitt−trigger buffer in ultra−small footprint.
The NLU2G17 input and output structures provide protection when
voltages up to 7.0 V are applied, regardless of the supply voltage.
The NLU2G17 can be used to enhance noise immunity or to square
up slowly changing waveforms.
Features
•High Speed: tPD = 4.0 ns (Typ) @ VCC = 5.0 V
•Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C
•Power Down Protection Provided on inputs
•Balanced Propagation Delays
•Overvoltage Tolerant (OVT) Input and Output Pins
•Ultra−Small Packages
•These are Pb−Free Devices
IN A2 OUT Y2
1
OUT Y1IN A1
GND
OUT Y2IN A2
1
2
3
5
4
Figure 1. Pinout (Top View)
Figure 2. Logic Symbol
6
VCC
IN A1 OUT Y1
1
PIN ASSIGNMENT
1
2
3IN A2
IN A1
GND
4
5V
CC
OUT Y2
FUNCTION TABLE
L
H
AY
L
H
6 OUT Y1
MARKING
DIAGRAMS
M = Date Code
www.onsemi.com
See detailed ordering and shipping information on page 4 o
f
this data sheet.
ORDERING INFORMATION
AM
1
UDFN6
1.2 x 1.0
CASE 517AA
1
ULLGA6
1.45 x 1.0
CASE 613AF AM
UDFN6
1.45 x 1.0
CASE 517AQ
UDFN6
1.0 x 1.0
CASE 517BX
1
M
1
M
5R
NLU2G17
www.onsemi.com
2
MAXIMUM RATINGS
Symbol Parameter Value Unit
VCC DC Supply Voltage −0.5 to +7.0 V
VIN DC Input Voltage −0.5 to +7.0 V
VOUT DC Output Voltage −0.5 to +7.0 V
IIK DC Input Diode Current VIN < GND −20 mA
IOK DC Output Diode Current VOUT < GND ±20 mA
IODC Output Source/Sink Current ±12.5 mA
ICC DC Supply Current Per Supply Pin ±25 mA
IGND DC Ground Current per Ground Pin ±25 mA
TSTG Storage Temperature Range −65 to +150 °C
TLLead Temperature, 1 mm from Case for 10 Seconds 260 °C
TJJunction Temperature Under Bias 150 °C
MSL Moisture Sensitivity Level 1
FRFlammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in
ILATCHUP Latchup Performance Above VCC and Below GND at 125°C (Note 2) ±500 mA
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be af fected.
1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2 ounce copper trace no air flow.
2. Tested to EIA / JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Max Unit
VCC Positive DC Supply Voltage 1.65 5.5 V
VIN Digital Input Voltage 0 5.5 V
VOUT Output Voltage 0 5.5 V
TAOperating Free−Air Temperature −55 +125 °C
Dt/DVInput Transition Rise or Fall Rate VCC = 3.3 V ± 0.3 V
VCC = 5.0 V ± 0.5 V 0
0No Limit
No Limit ns/V
NLU2G17
www.onsemi.com
3
DC ELECTRICAL CHARACTERISTICS
Symbol Parameter Conditions VCC
(V)
TA = 25 5C TA = +855CTA = −555C to
+1255C
Unit
Min Typ Max Min Max Min Max
VT+ Positive
Threshold
Voltage
3.0
4.5
5.5
2.0
3.0
3.6
2.2
3.15
3.85
2.2
3.15
3.85
2.2
3.15
3.85
V
VT− Negative
Threshold
Voltage
3.0
4.5
5.5
0.9
1.35
1.65
1.5
2.3
2.9
1.65
2.46
3.05
0.9
1.35
1.65
0.9
1.35
1.65
V
VHHysteresis
Voltage 3.0
4.5
5.5
0.30
0.40
0.50
0.57
0.67
0.74
1.20
1.40
1.60
0.30
0.40
0.50
1.20
1.40
1.60
0.30
0.40
0.50
1.20
1.40
1.60
V
VOH Minimum
High−Level
Output
Voltage
VIN w VT+MAX
IOH = −50 mA2.0
3.0
4.5
1.9
2.9
4.4
2.0
3.0
4.5
1.9
2.9
4.4
1.9
2.9
4.4
V
VIN w VT+MAX
IOH = −4 mA
IOH = −8 mA 3.0
4.5 2.58
3.94 2.48
3.80 2.34
3.66
VOL Maximum
Low−Level
Output
Voltage
VIN v VT−MIN
IOL = 50 mA2.0
3.0
4.5
0
0
0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
V
VIN v VT−MIN
IOL = 4 mA
IOL = 8 mA 3.0
4.5 0.36
0.36 0.44
0.44 0.52
0.52
IIN Input
Leakage
Current
0 v VIN v 5.5 V 0 to
5.5 ±0.1 ±1.0 ±1.0 mA
ICC Quiescent
Supply
Current
VIN = 5.5 V or
GND 5.5 1.0 10 40 mA
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns)
Symbol Parameter VCC
(V) Test
Condition
TA = 25 5C TA = +855CTA = −555C to
+1255C
Unit
Min Typ Max Min Max Min Max
tPLH,
tPHL Propagation Delay,
Input A to Output Y 3.0 to
3.6 CL = 15 pF 7.0 12.8 1.0 15 1.0 17 ns
CL = 50 pF 8.5 16.3 1.0 18.5 1.0 20.5
4.5 to
5.5 CL = 15 pF 4.0 8.6 1.0 10 1.0 11.5
CL = 50 pF 5.5 10.6 1.0 12 1.0 13.5
CIN Input Capacitance 5.0 10 10 10 pF
CPD Power Dissipation
Capacitance (Note 3) 5.0 7.0 pF
3. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without
load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no−load
dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC.
NLU2G17
www.onsemi.com
4
VCC
GND
50%
50% VCC
A or B
Y
tPHL
tPLH
Figure 3. Switching Waveforms Figure 4. Test Circuit
A 1−MHz square input wave is recommended for propagation delay tests.
CL
INPUT OUTPUT
RL
VH
VIN
Vout
V
CC
VT+
VT−
GND
VOH
VOL
VH
VIN
VOUT
V
CC
VT+
VT−
GND
VOH
VOL
(a) A Schmitt−Trigger Squares Up Inputs With Slow Rise and Fall Times (b) A Schmitt−Trigger Offers Maximum Noise Immunity
Figure 5. Typical Schmitt−Trigger Applications
ORDERING INFORMATION
Device Package Shipping†
NLU2G17MUTCG UDFN6, 1.2 x 1.0, 0.4P
(Pb−Free) 3000 / Tape & Reel
NLU2G17AMUTCG UDFN6, 1.45 x 1.0, 0.5P
(Pb−Free) 3000 / Tape & Reel
NLU2G17CMUTCG UDFN6, 1.0 x 1.0, 0.35P
(Pb−Free) 3000 / Tape & Reel
NLU2G17AMX1TCG ULLGA6, 1.45 x 1.0, 0.5P
(Pb−Free) 3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
NLU2G17
www.onsemi.com
5
PACKAGE DIMENSIONS
UDFN6 1.0x1.0, 0.35P
CASE 517BX
ISSUE O
ÉÉÉ
ÉÉÉ
ÉÉÉ
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.20 MM FROM TERMINAL TIP.
4. PACKAGE DIMENSIONS EXCLUSIVE OF
BURRS AND MOLD FLASH.
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
RECOMMENDED
DIM MIN MAX
MILLIMETERS
A0.45 0.55
A1 0.00 0.05
A3 0.13 REF
b0.12 0.22
D1.00 BSC
E1.00 BSC
e0.35 BSC
L0.25 0.35
L1 0.30 0.40
A B
E
D
0.10 C
PIN ONE
REFERENCE
TOP VIEW
0.10 C
A
A1
0.05 C
0.05 C
CSEATING
PLANE
SIDE VIEW
2X
2X
A3
BOTTOM VIEW
b
e
6X
0.10 B
0.05
AC
C
L5X
NOTE 3
L1
13
46
M
MDIMENSIONS: MILLIMETERS
0.22
5X
0.48 6X
1.18
0.53 PITCH
0.35
1
PKG
OUTLINE
NLU2G17
www.onsemi.com
6
PACKAGE DIMENSIONS
UDFN6, 1.2x1.0, 0.4P
CASE 517AA
ISSUE C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.25 AND
0.30 mm FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
ÉÉ
ÉÉ
A
B
E
D
BOTTOM VIEW
b
e
6X
0.10 B
0.05
AC
C
L5X
NOTE 3
2X
0.10 C
PIN ONE
REFERENCE
TOP VIEW
2X
0.10 C
10X
A
A1
(A3)
0.08 C
0.10 C
C
SEATING
PLANE
SIDE VIEW
L2
13
46
DIM MIN MAX
MILLIMETERS
A0.45 0.55
A1 0.00 0.05
A3 0.127 REF
b0.15 0.25
D1.20 BSC
E1.00 BSC
e0.40 BSC
L0.30 0.40
L1 0.00 0.15
L1
DETAIL A
Bottom View
(Optional)
ÉÉÉ
ÉÉÉ
ÉÉÉ
A1
A3
DETAIL B
Side View
(Optional)
EDGE OF PACKAGE
MOLD CMPD
EXPOSED Cu
L2 0.40 0.50
MOUNTING FOOTPRINT*
DIMENSIONS: MILLIMETERS
0.22
6X
0.42 6X
1.07
0.40
PITCH
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
NLU2G17
www.onsemi.com
7
PACKAGE DIMENSIONS
UDFN6 1.45x1.0, 0.5P
CASE 517AQ
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.30 mm FROM THE TERMINAL TIP.
ÉÉÉ
ÉÉÉ
A
B
E
D
BOTTOM VIEW
b
e
6X
0.10 B
0.05
AC
C
L6X
NOTE 3
0.10 C
PIN ONE
REFERENCE
TOP VIEW
0.10 C
6X
A
A1
0.05 C
0.05 C
CSEATING
PLANE
SIDE VIEW
13
46
DIM MIN MAX
MILLIMETERS
A0.45 0.55
A1 0.00 0.05
b0.20 0.30
D1.45 BSC
E1.00 BSC
e0.50 BSC
L0.30 0.40
L1 −−− 0.15
DIMENSIONS: MILLIMETERS
0.30
6X
1.24
0.53 PITCH
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
0.50
1
MOUNTING FOOTPRINT
PACKAGE
OUTLINE
L1
DETAIL A
L
OPTIONAL
CONSTRUCTIONS
L
ÉÉ
ÉÉ
ÉÉ
DETAIL B
MOLD CMPDEXPOSED Cu
OPTIONAL
CONSTRUCTIONS
A2 0.07 REF
6X
A2
DETAIL B
DET AIL A
NLU2G17
www.onsemi.com
8
PACKAGE DIMENSIONS
ULLGA6 1.45x1.0, 0.5P
CASE 613AF
ISSUE A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.30 mm FROM THE TERMINAL TIP.
4. A MAXIMUM OF 0.05 PULL BACK OF THE
PLATED TERMINAL FROM THE EDGE OF THE
PACKAGE IS ALLOWED.
ÉÉÉ
ÉÉÉ
A
B
E
D
BOTTOM VIEW
b
e
6X
0.10 B
0.05
AC
C
L5X
NOTE 3
0.10 C
PIN ONE
REFERENCE
TOP VIEW
0.10 C
6X
A
A1
0.05 C
0.05 C
C
SEATING
PLANE
SIDE VIEW
L1
13
46
DIM MIN MAX
MILLIMETERS
A−−− 0.40
A1 0.00 0.05
b0.15 0.25
D1.45 BSC
E1.00 BSC
e0.50 BSC
L0.25 0.35
L1 0.30 0.40
NOTE 4
SOLDERMASK DEFINED*
DIMENSIONS: MILLIMETERS
0.30
5X
0.49 6X
1.24
0.53 PITCH
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
0.50
1
MOUNTING FOOTPRINT
PKG
OUTLINE
P
UBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
NLU2G17/D
MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC).
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loc
al
Sales Representative
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor ’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer ’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body . Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
