FSGM0565RWDTU - Fairchild Semiconductor Corporation

March 2010

FSGM0565R • Rev. 1.0.2

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

FSGM0565R

Green-Mode Fairchild Power Switch (FPS™)

Features

 Soft Burst-Mode Operation for Low Standby Power

Consumption and Low Noise

 Precision Fixed Operating Frequency: 66kHz

 Pulse-by-Pulse Current Limit

 Various Protection Functions: Overload Protection

(OLP), Over-Voltage Protection (OVP), Abnormal

Over-Current Protection (AOCP), Internal Thermal

Shutdown (TSD) with Hysteresis, Output Short

Protection (OSP), and Under-Voltage Lockout

(UVLO) with Hysteresis

 Auto-Restart Mode

 Internal Startup Circuit

 Internal High-Voltage SenseFET: 650V

 Built-in Soft-Start: 15ms

Applications

 Power Supply for LCD TV and Monitor, STB and DVD

Combination

Description

The FSGM0565R is an integrated Pulse Width

Modulation (PWM) controller and SenseFET specifically

designed for offline Switch-Mode Power Supplies

(SMPS) with minimal external components. The PWM

controller includes an integrated fixed-frequency

oscillator, Under-Voltage Lockout (UVLO), Leading-

Edge Blanking (LEB), optimized gate driver, internal

soft-start, temperature-compensated precise current

sources for loop compensation, and self-protection

circuitry. Compared with a discrete MOSFET and PWM

controller solution, the FSGM series can reduce total

cost, component count, size, and weight; while

simultaneously increasing efficiency, productivity, and

system reliability. This device provides a basic platform

suited for cost-effective design of a flyback converter.

Ordering Information

Part Number Package

Operating

Junction

Temperature

Current

Limit

RDS(ON)

(Max.)

Output Power Table(2)

Replaces

Device

230VAC ± 15%(3) 85~265VAC

Adapter(4) Open

Frame(5) Adapter(4) Open

Frame(5)

FSGM0565RWDTU

TO-220F

6-Lead(1)

W-Forming

-40°C ~

+125°C 2.20A 2.2Ω 70W 80W 41W 60W FSDM0565RE

FSGM0565RUDTU

TO-220F

6-Lead(1)

U-Forming

-40°C ~

+125°C 2.20A 2.2Ω 70W 80W 41W 60W FSDM0565RE

FSGM0565RLDTU

TO-220F

6-Lead(1)

L-Forming

-40°C ~

+125°C 2.20A 2.2Ω 70W 80W 41W 60W FSDM0565RE

Notes:

1. Pb-free package per JEDEC J-STD-020B.

2. The junction temperature can limit the maximum output power.

3. 230VAC or 100/115VAC with voltage doubler.

4. Typical continuous power in a non-ventilated enclosed adapter measured at 50°C ambient temperature.

5. Maximum practical continuous power in an open-frame design at 50°C ambient temperature.

FSGM0565R • Rev. 1.0.2 2

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Application Circuit

Figure 1. Typical Application Circuit

Internal Block Diagram

Figure 2. Internal Block Diagram

FSGM0565R • Rev. 1.0.2 3

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Pin Configuration

Figure 3. Pin Configuration (Top View)

Pin Definitions

Pin # Name Description

1 Drain SenseFET Drain. High-voltage power SenseFET drain connection.

2 GND Ground. This pin is the control ground and the SenseFET source.

3 VCC Power Supply. This pin is the positive supply input, which provides the internal operating

current for both startup and steady-state operation.

4 FB

Feedback. This pin is internally connected to the inverting input of the PWM comparator. The

collector of an opto-coupler is typically tied to this pin. For stable operation, a capacitor

should be placed between this pin and GND. If the voltage of this pin reaches 6V, the

overload protection triggers, which shuts down the FPS.

5 N.C. No connection.

6 VSTR

Startup. This pin is connected directly, or through a resistor, to the high-voltage DC link. At

startup, the internal high-voltage current source supplies internal bias and charges the

external capacitor connected to the VCC pin. Once VCC reaches 12V, the internal current

source (ICH) is disabled.

FSGM0565R • Rev. 1.0.2 4

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Absolute Maximum Ratings

Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be

operable above the recommended operating conditions and stressing the parts to these levels is not recommended.

In addition, extended exposure to stresses above the recommended operating conditions may affect device

reliability. The absolute maximum ratings are stress ratings only.

Symbol Parameter Min. Max. Unit

VSTR V

STR Pin Voltage 650 V

VDS Drain Pin Voltage 650 V

VCC V

CC Pin Voltage 26 V

VFB Feedback Pin Voltage -0.3 12 V

IDM Drain Current Pulsed 11 A

IDS Continuous Switching Drain Current(6) TC=25°C 5.6 A

TC=100°C 3.4 A

EAS Single Pulsed Avalanche Energy(7) 295 mJ

PD Total Power Dissipation (TC=25°C)(8) 45 W

TJ Maximum Junction Temperature +150

°C

Operating Junction Temperature(9) -40 +125 °C

TSTG Storage Temperature -55 +150 °C

VISO Minimum Isolation Range(10) 2.5 V

ESD Electrostatic

Discharge Capability

Human Body Model, JESD22-A114 2 kV

Charged Device Model, JESD22-C101 2

Notes:

6. Repetitive peak switching current when the inductive load is assumed: Limited by maximum duty (DMAX=0.75)

and junction temperature (see Figure 4).

7. L=45mH, starting TJ=25°C.

8. Infinite cooling condition (refer to the SEMI G30-88).

9. Although this parameter guarantees IC operation, it does not guarantee all electrical characteristics.

10. The voltage between the package back side and the lead is guaranteed.

Figure 4. Repetitive Peak Switching Current

Thermal Impedance

TA=25°C unless otherwise specified.

Symbol Parameter Value Unit

JA Junction-to-Ambient Thermal Impedance(11) 62.5 °C/W

JC Junction-to-Case Thermal Impedance(12) 3 °C/W

Notes:

11. Infinite cooling condition (refer to the SEMI G30-88).

12. Free standing with no heat-sink under natural convection.

FSGM0565R • Rev. 1.0.2 5

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Electrical Characteristics

TJ = 25°C unless otherwise specified.

Symbol Parameter Conditions Min. Typ. Max. Unit

SenseFET Section

BVDSS Drain-Source Breakdown Voltage VCC = 0V, ID = 250µA 650 V

IDSS Zero-Gate-Voltage Drain Current VDS = 520V, TA = 125°C 250 µA

RDS(ON) Drain-Source On-State Resistance VGS = 10V, ID =1A 1.8 2.2 

CISS Input Capacitance(13) VDS = 25V,VGS = 0V,

f = 1MHz 515 pF

COSS Output Capacitance(13) VDS = 25V,VGS = 0V,

f = 1MHz 75 pF

tr Rise Time VDS = 325V, ID = 4A,

RG = 25 26 ns

tf Fall Time VDS = 325V, ID = 4A,

RG = 25 25 ns

td(on) Turn-on Delay Time VDS = 325V, ID = 4A,

RG = 25 14 ns

td(off) Turn-off Delay Time VDS = 325V, ID = 4A,

RG = 25 32 ns

Control Section

fS Switching Frequency VCC = 14V, VFB = 4V 60 66 72 kHz

ΔfS Switching Frequency Variation(13) - 25°C < TJ < 125°C ±5 ±10 %

DMAX Maximum Duty Ratio VCC = 14V, VFB = 4V 65 70 75 %

DMIN Minimum Duty Ratio VCC = 14V, VFB = 0V 0 %

IFB Feedback Source Current VFB = 0 160 210 260 µA

VSTART

UVLO Threshold Voltage VFB = 0V, VCC Sweep 11 12 13 V

VSTOP After Turn-on, VFB = 0V 7.0 7.5 8.0 V

VOP V

CC Operating Range 13 23 V

tS/S Internal Soft-Start Time VSTR = 40V, VCC Sweep 15 ms

Burst-Mode Section

VBURH

Burst-Mode Voltage VCC = 14V, VFB Sweep

0.6 0.7 0.8 V

VBURL 0.4 0.5 0.6 V

Hys 200 mV

Protection Section

ILIM Peak Drain Current Limit di/dt = 300mA/µs 2.0 2.2 2.4 A

VSD Shutdown Feedback Voltage VCC = 14V, VFB Sweep 5.5 6.0 6.5 V

IDELAY Shutdown Delay Current VCC = 14V, VFB = 4V 2.5 3.3 4.1 µA

tLEB Leading-Edge Blanking Time(13)(14) 300 ns

VOVP Over-Voltage Protection VCC Sweep 23.0 24.5 26.0 V

tOSP

Output Short

Protection(13)

Threshold Time OSP Triggered When 1.0 1.2 1.4 µs

VOSP Threshold VFB t

ON<tOSP & VFB>VOSP 1.8 2.0 2.2 V

tOSP_FB V

FB Blanking Time (Lasts Longer than tOSP_FB) 2.0 2.5 3.0 µs

TSD

Thermal Shutdown Temperature(13) Shutdown Temperature 130 140 150 °C

Hys Hysteresis 30

°C

Continued on the following page…

FSGM0565R • Rev. 1.0.2 6

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Electrical Characteristics (Continued)

TJ = 25°C unless otherwise specified.

Symbol Parameter Conditions Min. Typ. Max. Unit

Total Device Section

IOP

Operating Supply Current,

(Control Part in Burst Mode) VCC = 14V, VFB = 0V 1.2 1.6 2.0 mA

IOPS Operating Switching Current,

(Control Part and SenseFET Part) VCC = 14V, VFB = 4V 2.0 2.5 3.0 mA

ISTART Start Current VCC = 11V (Before VCC

Reaches VSTART) 0.5 0.6 0.7 mA

ICH Startup Charging Current VCC = VFB = 0V, VSTR = 40V 1.00 1.15 1.30 mA

VSTR Minimum VSTR Supply Voltage VCC = VFB = 0V, VSTR Sweep 26 V

Notes:

13. Although these parameters are guaranteed, they are not 100% tested in production.

14. tLEB includes gate turn-on time.

Comparison of FSDM0565RE and FSGM0565R

Function FSDM0565RE FSGM0565R Advantages of FSGM0565R

Burst Mode Advanced Burst Advanced Soft Burst Low noise and low standby power

Lightning Surge Strong Enhanced SenseFET and controller against

lightning surge

Soft-Start 10ms (Built-in) 15ms (Built-in) Longer soft-start time

Protections

OLP

OVP

TSD

OLP

OVP

OSP

AOCP

TSD with Hysteresis

Enhanced protections and high reliability

Power Balance Long TCLD Very Short TCLD The difference of input power between the low

and high input voltage is quite small.

FSGM0565R • Rev. 1.0.2 7

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Typical Performance Characteristics

Characteristic graphs are normalized at TA=25°C.

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

Figure 5. Operating Supply Current (IOP) vs. T

Figure 6. Operating Switching Current (IOPS) vs. T

0.60

0.70

0.80

0.90

1.00

1.10

1.20

1.30

1.40

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

Figure 7. Startup Charging Current (ICH) vs. T

Figure 8. Peak Drain Current Limit (ILIM) vs. T

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

Figure 9. Feedback Source Current (IFB) vs. T

Figure 10. Shutdown Delay Current (IDELAY) vs. T

FSGM0565R • Rev. 1.0.2 8

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Typical Performance Characteristics

Characteristic graphs are normalized at TA=25°C.

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

Figure 11. UVLO Threshold Voltage (VSTART) vs. T

Figure 12. UVLO Threshold Voltage (VSTOP) vs. T

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

Figure 13. Shutdown Feedback Voltage (VSD) vs. T

Figure 14. Over-Voltage Protection (VOVP) vs. T

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

-40℃ -25℃ 0℃ 25℃ 50℃ 75℃ 100℃ 125℃

Normalized

Temperature [°C]

Figure 15. Switching Frequency (fS) vs. T

Figure 16. Maximum Duty Ratio (DMA

) vs. T

FSGM0565R • Rev. 1.0.2 9

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Functional Description

1. Startup: At startup, an internal high-voltage current

source supplies the internal bias and charges the

external capacitor (CVcc) connected to the VCC pin, as

illustrated in Figure 17. When VCC reaches 12V, the

FSGM0565R begins switching and the internal high-

voltage current source is disabled. The FSGM0565R

continues normal switching operation and the power is

supplied from the auxiliary transformer winding unless

VCC goes below the stop voltage of 7.5V.

Figure 17. Startup Block

2. Soft-Start: The FSGM0565R has an internal soft-

start circuit that increases PWM comparator inverting

input voltage, together with the SenseFET current,

slowly after it starts. The typical soft-start time is 15ms.

The pulse width to the power switching device is

progressively increased to establish the correct working

conditions for transformers, inductors, and capacitors.

The voltage on the output capacitors is progressively

increased to smoothly establish the required output

voltage. This helps prevent transformer saturation and

reduces stress on the secondary diode during startup.

3. Feedback Control: This device employs current-

mode control, as shown in Figure 18. An opto-coupler

(such as the FOD817) and shunt regulator (such as the

KA431) are typically used to implement the feedback

network. Comparing the feedback voltage with the

voltage across the RSENSE resistor makes it possible to

control the switching duty cycle. When the reference pin

voltage of the shunt regulator exceeds the internal

reference voltage of 2.5V, the opto-coupler LED current

increases, pulling down the feedback voltage and

reducing the drain current. This typically occurs when

the input voltage increases or the output load decreases.

3.1 Pulse-by-Pulse Current Limit: Because current-

mode control is employed, the peak current through

the SenseFET is limited by the inverting input of PWM

comparator (VFB*), as shown in Figure 18. Assuming

that the 210μA current source flows only through the

internal resistor (3R + R =11.6k), the cathode

voltage of diode D2 is about 2.4V. Since D1 is

blocked when the feedback voltage (VFB) exceeds

2.4V, the maximum voltage of the cathode of D2 is

clamped at this voltage. Therefore, the peak value of

the current through the SenseFET is limited.

3.2 Leading-Edge Blanking (LEB): At the instant the

internal SenseFET is turned on, a high-current spike

usually occurs through the SenseFET, caused by

primary-side capacitance and secondary-side rectifier

reverse recovery. Excessive voltage across the

RSENSE resistor leads to incorrect feedback operation

in the current mode PWM control. To counter this

effect, the FSGM0565R employs a leading-edge

blanking (LEB) circuit. This circuit inhibits the PWM

comparator for tLEB (300ns) after the SenseFET is

turned on.

Figure 18. Pulse Width Modulation Circuit

FSGM0565R • Rev. 1.0.2 10

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

4. Protection Circuits: The FSGM0565R has several

self-protective functions, such as Overload Protection

(OLP), Abnormal Over-Current Protection (AOCP),

Output Short Protection (OSP), Over-Voltage Protection

(OVP), and Thermal Shutdown (TSD). All the

protections are implemented as auto-restart. Once the

fault condition is detected, switching is terminated and

the SenseFET remains off. This causes VCC to fall.

When VBCCB falls to the Under-Voltage Lockout (UVLO)

stop voltage of 7.5V, the protection is reset and the

startup circuit charges the VCC capacitor. When VCC

reaches the start voltage of 12.0V, the FSGM0565R

resumes normal operation. If the fault condition is not

removed, the SenseFET remains off and VCC drops to

stop voltage again. In this manner, the auto-restart can

alternately enable and disable the switching of the

power SenseFET until the fault condition is eliminated.

Because these protection circuits are fully integrated

into the IC without external components, the reliability is

improved without increasing cost.

Figure 19. Auto Restart Protection Waveforms

4.1 Overload Protection (OLP): Overload is defined

as the load current exceeding its normal level due to

an unexpected abnormal event. In this situation, the

protection circuit should trigger to protect the SMPS.

However, even when the SMPS is in normal

operation, the overload protection circuit can be

triggered during the load transition. To avoid this

undesired operation, the overload protection circuit is

designed to trigger only after a specified time to

determine whether it is a transient situation or a true

overload situation. Because of the pulse-by-pulse

current limit capability, the maximum peak current

through the SenseFET is limited, and therefore the

maximum input power is restricted with a given input

voltage. If the output consumes more than this

maximum power, the output voltage (VOUT) decreases

below the set voltage. This reduces the current

through the opto-coupler LED, which also reduces

the opto-coupler transistor current, thus increasing

the feedback voltage (VFB). If VFB exceeds 2.4V, D1 is

blocked and the 3.3µA current source starts to charge

CFB slowly up. In this condition, VFB continues

increasing until it reaches 6.0V, when the switching

operation is terminated, as shown in Figure 20. The

delay time for shutdown is the time required to charge

CFB from 2.4V to 6.0V with 3.3µA. A 25 ~ 50ms delay

is typical for most applications. This protection is

implemented in auto-restart mode.

Figure 20. Overload Protection

4.2 Abnormal Over-Current Protection (AOCP):

When the secondary rectifier diodes or the

transformer pins are shorted, a steep current with

extremely high di/dt can flow through the SenseFET

during the minimum turn-on time. Even though the

FSGM0565R has overload protection, it is not

enough to protect the FSGM0565R in that abnormal

case; since severe current stress is imposed on the

SenseFET until OLP is triggered. The FSGM0565R

internal AOCP circuit is shown in Figure 21. When

the gate turn-on signal is applied to the power

SenseFET, the AOCP block is enabled and monitors

the current through the sensing resistor. The voltage

across the resistor is compared with a preset AOCP

level. If the sensing resistor voltage is greater than

the AOCP level, the set signal is applied to the S-R

latch, resulting in the shutdown of the SMPS.

Figure 21. Abnormal Over-Current Protection

FSGM0565R • Rev. 1.0.2 11

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

4.3. Output Short Protection (OSP): If the output is

shorted, steep current with extremely high di/dt can

flow through the SenseFET during the minimum turn-

on time. Such a steep current brings high-voltage

stress on drain of SenseFET when turned off. To

protect the device from such an abnormal condition,

OSP is included. It is comprised of detecting VFB and

SenseFET turn-on time. When the VFB is higher than

2V and the SenseFET turn-on time is lower than

1.2μs, the FSGM0565R recognizes this condition as

an abnormal error and shuts down PWM switching

until VCC reaches VSTART again. An abnormal

condition output short is shown in Figure 22.

Figure 22. Output Short Protection

4.4 Over-Voltage Protection (OVP): If the

secondary-side feedback circuit malfunctions or a

solder defect causes an opening in the feedback

path, the current through the opto-coupler transistor

becomes almost zero. Then VFB climbs up in a similar

manner to the overload situation, forcing the preset

maximum current to be supplied to the SMPS until

the overload protection is triggered. Because more

energy than required is provided to the output, the

output voltage may exceed the rated voltage before

the overload protection is triggered, resulting in the

breakdown of the devices in the secondary side. To

prevent this situation, an OVP circuit is employed. In

general, the VCC is proportional to the output voltage

and the FSGM0565R uses VCC instead of directly

monitoring the output voltage. If VCC exceeds 24.5V,

an OVP circuit is triggered, resulting in the

termination of the switching operation. To avoid

undesired activation of OVP during normal operation,

VCC should be designed to be below 24.5V.

4.5 Thermal Shutdown (TSD): The SenseFET and

the control IC on a die in one package makes it

easier for the control IC to detect the over

temperature of the SenseFET. If the temperature

exceeds ~140°C, the thermal shutdown is triggered

and the FSGM0565R stops operation. The

FSGM0565R operates in auto-restart mode until the

temperature decreases to around 110°C, when

normal operation resumes.

5. Soft Burst-Mode Operation: To minimize power

dissipation in standby mode, the FSGM0565R enters

burst-mode operation. As the load decreases, the

feedback voltage decreases. As shown in Figure 23,

the device automatically enters burst mode when the

feedback voltage drops below VBURL (500mV). At this

point, switching stops and the output voltages start to

drop at a rate dependent on standby current load. This

causes the feedback voltage to rise. Once it passes

VBURH (700mV), switching resumes. At this point, the

drain current peak increases gradually. This soft burst-

mode can reduce audible noise during burst-mode

operation. The feedback voltage then falls and the

process repeats. Burst-mode operation alternately

enables and disables switching of the SenseFET,

thereby reducing switching loss in standby mode.

Figure 23. Burst-Mode Operation

FSGM0565R • Rev. 1.0.2 12

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Typical Application Circuit

Application Input Voltage Rated Output Rated Power

LCD TV, Monitor

Power Supply 85 ~ 265VAC 5.0V(2A)

14.0V(2.8A) 49.2W

Key Design Notes:

1. The delay time for overload protection is designed to be about 40ms with C105 (33nF). OLP time between 25ms

(22nF) and 50ms (43nF) is recommended.

2. The SMD-type capacitor (C106) must be placed as close as possible to the VCC pin to avoid malfunction by

abrupt pulsating noises and to improve ESD and surge immunity. Capacitance between 100nF and 220nF is

recommended.

1. Schematic

Figure 24. Schematic of Demonstration Board

FSGM0565R • Rev. 1.0.2 13

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

2. Transformer

EER3019

N14V

Np/2

N5V

Np/2

Figure 25. Schematic of Transformer

3. Winding Specification

Pin (S → F) Wire Turns Winding Method Barrier Tape

TOP BOT Ts

Np /2 3  2 0.35×1 22 Solenoid Winding 2.0mm 1

Insulation: Polyester Tape t = 0.025mm, 2 Layers

N5V 8  9 0.4×3 (TIW) 3 Solenoid Winding

Insulation: Polyester Tape t = 0.025mm, 2 Layers

N14V 10  8 0.4×3 (TIW) 5 Solenoid Winding

Insulation: Polyester Tape t = 0.025mm, 2 Layers

N5V 7  6 0.4×3 (TIW) 3 Solenoid Winding

Insulation: Polyester Tape t = 0.025mm, 2 Layers

Na 4  5 0.15×1 7 Solenoid Winding 4.0mm 4.0mm 1

Insulation: Polyester Tape t = 0.025mm, 2 Layers

Np/2 2  1 0.35×1 21 Solenoid Winding 2.0mm 1

Insulation: Polyester Tape t = 0.025mm, 2 Layers

4. Electrical Characteristics

Pin Specification Remark

Inductance 1－3 700μH ± 7% 67kHz, 1V

Leakage 1－3 15μH Maximum Short All Other Pins

5. Core & Bobbin

 Core: EER3019 (Ae=134.0mm2)

 Bobbin: EER3019

FSGM0565R • Rev. 1.0.2 14

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

6. Bill of Materials

Part # Value Note Part # Value Note

Fuse Capacitor

F101 250V 3.15A C101 220nF/275V Box (Pilkor)

NTC C102 150nF/275V Box (Pilkor)

NTC101 5D-11 DSC C103

100μF/400V Electrolytic (SamYoung)

Resistor C104 3.3nF/630V Film (Sehwa)

R101 1.5M, J 1W C105 33nF/100V Film (Sehwa)

R102 75k, J 1/2W C106 220nF SMD (2012)

R103 51k, J 1W C107 47μF/50V Electrolytic (SamYoung)

R104 51, J 1/2W C201 1000μF/25V Electrolytic (SamYoung)

R201 620, F 1/4W, 1% C202 1000μF/25V Electrolytic (SamYoung)

R202 1.2k, F 1/4W, 1% C203 2200μF/10V Electrolytic (SamYoung)

R203 18k, F 1/4W, 1% C204 1000μF/16V Electrolytic (SamYoung)

R204 8k, F 1/4W, 1% C205 68nF/100V Film (Sehwa)

R205 8k, F 1/4W, 1% C206 100nF SMD (2012)

IC C207 100nF SMD (2012)

FSGM0565R FSGM0565R Fairchild

Semiconductor C301 4.7nF/Y2 Y-cap (Samhwa)

IC201 KA431LZ

Fairchild

Semiconductor Inductor

IC301 FOD817C

Fairchild

Semiconductor LF101 20mH Line filter 0.7Ø

Diode L201 5μH 5A Rating

D101 1N4007 Vishay L202 5μH 5A Rating

D102 UF4004 Vishay Jumper

ZD101 1N4749 Vishay J101

D201 MBR20150CT Fairchild

Semiconductor Transformer

D202 FYPF2006DN

Fairchild

Semiconductor T101 700μH

BD101 G3SBA60 Vishay

FSGM0565R • Rev. 1.0.2 15

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Physical Dimensions

NOTES: UNLESS OTHERWISE SPECIFIED

A) THIS PACKAGE DOES NOT COMPLY

TO ANY CURRENT PACKAGING STANDARD.

B) ALL DIMENSIONS ARE IN MILLIMETERS.

C) DIMENSIONS ARE EXCLUSIVE OF BURRS,

MOLD FLASH, AND TIE BAR EXTRUSIONS.

D) LEADFORM OPTION A

E) DFAWING FILENAME: TO220A06REV4

1.40

1.20

0.80

0.70

0.50

1,3,5 2,4,6

8.13

7.13

16.07

15.67

3.48

2.88

3.06

2.46

24.00

23.00

20.00

19.00

6.90

6.50

2.74

2.34

3.40

3.20

10.16

9.96

(5.40)

(1.13)

0.60

0.45

(0.48)

(0.70)

5° 5°

(7.15)

(13.05)

2.19

1.27

3.81

1.75

(7.00) Ø3.28

3.08

R0.55

Figure 26. TO-220F-6L (W-Forming)

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner

without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify

or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically

the warranty therein, which covers Fairchild products.

Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:

http://www.fairchildsemi.com/packaging/.

FSGM0565R • Rev. 1.0.2 16

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Physical Dimensions

5° 5°

Ø3.28

3.08

(7.00)

1.75

3.81

1.27

2.19

(0.70)

0.60

0.45

(0.88)

(5.40)

10.36

9.96

3.40

3.20

2.74

2.34

19.97

18.97

3.06

2.46

3.48

2.88

16.07

15.67

8.13

7.13

#1 #6 #2,4 #3,5

0.70

0.50 5PLCS

0.80

0.70 5PLCS

1.40

1.20

24.00

23.00

13.05

7.15

7.29

6.69

#1,6

(3.81)

(0.48)

5.18

4.98

6.88

6.48

0.20 AB

4.80

4.40

NOTES:

A) NO PACKAGE STANDARD APPLIES.

B) DIMENSIONS ARE EXCLUSIVE OF BURRS,

MOLD FLASH, AND TIE BAR EXTRUSIONS.

C) DIMENSIONS ARE IN MILLIMETERS.

D) DRAWING FILENAME : MKT-TO220F06REV2

18.94

17.94

R0.55

Figure 27. TO-220F-6L (U-Forming)

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner

without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify

or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically

the warranty therein, which covers Fairchild products.

Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:

http://www.fairchildsemi.com/packaging/.

FSGM0565R • Rev. 1.0.2 17

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)

Physical Dimensions

NOTES:

A) NO PACKAGE STANDARD APPLIES.

B) DIMENSIONS ARE EXCLUSIVE OF BURRS,

MOLD FLASH, AND TIE BAR EXTRUSIONS.

C) DIMENSIONS ARE IN MILLIMETERS.

D) DRAWING FILENAME : MKT-TO220E06REV2

16.08

15.68

Ø3.28

3.08

2.19

1.27

3.81

1.75

0.85

0.75 5PLCS

5° 5°

(0.70)

0.61

0.46

3.18

#2,4,6

#1,3,5

2.74

2.34

#1 #6

R1.00

0.65

0.55 6PLCS

3.40

3.20

10.36

9.96

4.90

4.70 6PLCS

6.88

6.48

(1.13)

1.30

1.05

0.20 AB

4.80

4.40

(17.83)

(21.01)

0.05 C

R1.00

5.18

4.98

Figure 28. TO-220F-6L (L-Forming)

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner

without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify

or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically

the warranty therein, which covers Fairchild products.

Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:

http://www.fairchildsemi.com/packaging/.

FSGM0565R • Rev. 1.0.2 18

FSGM0565R — Green-Mode Fairchild Power Switch (FPS™)