Web page Tools & software Sample & buy Support & FAQ Document 101-1 Chip Inductors-1008CS Series (2520) Halogen Free * High SRF and excellent Q values * Tight tolerances, many values at 1% * 40 inductance values from 10 nH to 8.2 H AEC Typical Q vs Frequency 120 100 100 47 nH 90 80 Q Factor Q200 +125C Designer's Kit C300 contains 10 each of all 5% tolerance values Core material Ceramic Environmental RoHS compliant, halogen free Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 29.6 - 37.4 mg Ambient temperature -40C to +125C with Irms current Maximum part temperature +140C (ambient + temp rise). Storage temperature Component: -40C to +140C. Tape and reel packaging: -40C to +80C Resistance to soldering heat Max three 40 second reflows at +260C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +25 to +125 ppm/C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000 per 7 reel; 7500 per 13 reel. Plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing, 2.0 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. 100 nH 12 nH 70 60 330 nH 50 750 nH 1800 nH 40 30 20 0 C B overall 10 10 100 1000 Frequency (MHz) 10000 F A Typical L vs Frequency E terminal A B max max 0.115 0.110 2,92 2,79 H D Pick and place material I G J F I Terminal wraparound: approx 0.010/0,25 both ends Recommended Land Pattern C D max ref E F G H I J 0.080 0.020 0.080 0.020 0.060 0.100 0.040 0.050 inches 2,03 0,51 2,03 0,51 1,52 2,54 1,02 1,27 mm Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. Document 101-1 Revised 10/12/15 Document 101-2 1008CS Series (2520) Part number1 Halogen Free AEC Q200 +125C Inductance2 (nH) 1008CS-100X_E_ 10 @ 50 MHz 1008CS-120X_E_ 12 @ 50 MHz 1008CS-150X_E_ 15 @ 50 MHz 1008CS-180X_E_ 18 @ 50 MHz 1008CS-220X_E_ 22 @ 50 MHz 1008CS-270X_E_ 27 @ 50 MHz 1008CS-330X_E_ 33 @ 50 MHz 1008CS-390X_E_ 39 @ 50 MHz 1008CS-470X_E_ 47 @ 50 MHz 1008CS-560X_E_ 56 @ 50 MHz 1008CS-680X_E_ 68 @ 50 MHz 1008CS-820X_E_ 82 @ 50 MHz 1008CS-101X_E_ 100 @ 25 MHz 1008CS-121X_E_ 120 @ 25 MHz 1008CS-151X_E_ 150 @ 25 MHz 1008CS-181X_E_ 180 @ 25 MHz 1008CS-221X_E_ 220 @ 25 MHz 1008CS-271X_E_ 270 @ 25 MHz 1008CS-331X_E_ 330 @ 25 MHz 1008CS-391X_E_ 390 @ 25 MHz 1008CS-471X_E_ 470 @ 25 MHz 1008CS-561X_E_ 560 @ 25 MHz 1008CS-621X_E_ 620 @ 25 MHz 1008CS-681X_E_ 680 @ 25 MHz 1008CS-751X_E_ 750 @ 25 MHz 1008CS-821X_E_ 820 @ 25 MHz 1008CS-911X_E_ 910 @ 25 MHz 1008CS-102X_E_ 1000 @ 25 MHz 1008CS-122X_E_ 1200 @ 7.9 MHz 1008CS-132X_E_ 1300 @ 7.9 MHz 1008CS-152X_E_ 1500 @ 7.9 MHz 1008CS-182X_E_ 1800 @ 7.9 MHz 1008CS-222X_E_ 2200 @ 7.9 MHz 1008CS-272X_E_ 2700 @ 7.9 MHz 1008CS-332X_E_ 3300 @ 7.9 MHz 1008CS-392X_E_ 3900 @ 7.9 MHz 1008CS-472X_E_ 4700 @ 7.9 MHz 1008CS-562XJE_ 5600 @ 7.9 MHz 1008CS-682XJE_ 6800 @ 7.9 MHz 1008CS-822XJE_ 8200 @ 2.5 MHz Percent SRF min5 tolerance3 Q min4 (MHz) 5,2 5,2 5,2 5,2 5,2,1 5,2 5,2 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5 5 5 1. When ordering, specify tolerance, termination and packaging codes: 1008CS-472XJEC F = 1% G = 2% J = 5% (Table shows stock tolerances in bold.) Termination: E = Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. L = RoHS compliant, not halogen-free. Silver-palladium-platinum-glass frit terminations. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7 machine-ready reel. EIA-481 embossed plastic tape (2000 per full reel). D = 13 machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 per full reel). Tolerance: 50 @ 500 MHz 50 @ 500 MHz 50 @ 500 MHz 50 @ 350 MHz 55 @ 350 MHz 55 @ 350 MHz 60 @ 350 MHz 60 @ 350 MHz 65 @ 350 MHz 65 @ 350 MHz 65 @ 350 MHz 60 @ 350 MHz 60 @ 350 MHz 60 @ 350 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 45 @ 100 MHz 35 @ 50 MHz 35 @ 50 MHz 35 @ 50 MHz 25 @ 50 MHz 28 @ 50 MHz 28 @ 50 MHz 28 @ 50 MHz 22 @ 25 MHz 22 @ 25 MHz 20 @ 25 MHz 20 @ 25 MHz 16 @ 7.9 MHz 18 @ 7.9 MHz 18 @ 7.9 MHz 4100 3300 2500 2500 2400 1600 1600 1500 1500 1300 1300 1000 1000 950 850 750 700 600 570 500 450 415 375 375 360 350 320 290 250 200 200 160 160 140 110 100 90 20 40 25 DCR max6 (Ohms) Irms7 (mA) Color code8 0.08 0.09 0.10 0.11 0.12 0.13 0.14 0.15 0.16 0.18 0.20 0.22 0.56 0.63 0.70 0.77 0.84 0.91 1.05 1.12 1.19 1.33 1.40 1.47 1.54 1.61 1.68 1.75 2.00 2.25 2.3 2.6 2.8 3.2 3.4 3.6 4.0 4.0 4.9 6.0 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 650 650 580 620 500 500 450 470 470 400 300 400 360 400 380 370 310 310 330 300 280 290 290 260 260 240 200 170 Black Red Orange Yellow Blue Black Orange Violet Red Yellow Gray Red Violet White Red Orange Green White Orange Blue Black Green Blue Gray Black Brown Red Yellow Blue Red Gray Brown Orange Green Violet Gray White Black Brown Red 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Tolerances in bold are stocked for immediate shipment. 4. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 5. SRF measured using an Aglilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture. 6. DCR measured on a Cambridge Technology micro-ohmmeter and a Coilcraft CCF840 test fixture. 7. Current that causes a 15C temperature rise from 25C ambient. This information is for reference only and does not represent absolute maximum ratings. 8. Current production parts are marked with one dot. Prior production parts were marked with three dots. Single color dots are not unique identifiers and correspond to multiple inductance values. Part marking does not indicate polarity. 9. Electrical specifications at 25C. Refer to Doc 362 "Soldering Surface Mount Components" before soldering. Document 101-2 Revised 08/03/15