ECG004 The Communications Edge TM InGaP HBT Gain Block Product Features Product Description * +13.5 dBm P1dB at 1 GHz * +28 dBm OIP3 at 1 GHz * 16.2 dB Gain at 1 GHz * 3.2 dB Noise Figure * Available in Lead-free / green SOT-89 Package Style * Internally matched to 50 The ECG004B is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surface-mount package. At 1000 MHz, the ECG004B typically provides 16 dB of gain, +28 dBm Output IP3, and +13.5 dBm P1dB. The ECG004B consists of Darlington pair amplifiers using the high reliability InGaP/GaAs HBT process technology and only requires DC-blocking capacitors, a bias resistor, and an inductive RF choke for operation. The device is ideal for wireless applications and is available in a lowcost, surface-mountable lead-free/green/RoHS-compliant SOT-89 package. All devices are 100% RF and DC tested. The broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as GPRS, GSM, CDMA, and W-CDMA. In addition, the ECG004B will work for other various applications within the DC to 6 GHz frequency range such as CATV and mobile wireless. Applications Mobile Infrastructure CATV / FTTX W-LAN / ISM RFID WiMAX / WiBro Specifications (1) Parameter Functional Diagram GND * DC - 6 GHz * * * * * Product Information 4 1 2 3 RF IN GND RF OUT Function Input Output/Bias Ground Pin No. 1 3 2, 4 Typical Performance (1) Units Min MHz MHz dB dBm dBm MHz dB dB dB dBm dBm dB V mA DC Operational Bandwidth Test Frequency Gain Output P1dB Output IP3 (3) Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure Device Voltage Device Current 13.5 10.5 3.1 Typ 1000 16.2 +13.5 +28 2000 15.9 19 15 +13 +27 3.2 3.4 35 Max Parameter 6000 Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure Units MHz dB dB dB dBm dBm dB Typical 500 16.5 -31 -28 +13.6 +28 3.3 900 16.2 -28 -21 +13.5 +28 3.2 1900 15.5 -19 -21 +13 +27 3.3 2140 15.2 -18 -14 +13 +27 3.3 3.7 1. Test conditions unless otherwise noted: 25 C, Supply Voltage = +5 V, Rbias = 45.3 , 50 System. 2. 3OIP measured with two tones at an output power of -1 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature Device Current RF Input Power (continuous) Junction Temperature Rating -40 to +85 C -55 to +150 C 150 mA +12 dBm +250 C Ordering Information Part No. Description ECG004B-G InGaP HBT Gain Block ECG004B-PCB 700 - 2400 MHz Fully Assembled Eval. Board (lead-free/green/RoHS-compliant SOT-89 package) Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 1 of 4 April 2006 ECG004 The Communications Edge TM InGaP HBT Gain Block Product Information Typical Device RF Performance Supply Bias = +5 V, Rbias = 45.3 , Icc = 35 mA Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure MHz dB dB dB dBm dBm dB 100 16.8 -18 -16.7 +13.4 +28 3.3 500 16.5 -31 -28 +13.5 +28 3.3 900 16.3 -28 -21 +13.5 +28 3.3 1900 15.5 -19 -15 +12.9 +27 2.9 2140 15.2 -18 -14 +12.9 +27 3.0 2400 14.9 -17 -12.5 +12.8 +27 3.4 3500 13.1 -12.6 -9 +11.7 +24 3.5 5800 10.2 -5 -4 +5 1. Test conditions: T = 25 C, Supply Voltage = +5 V, Device Voltage = +3.9 V, Rbias = 45.3 , Icc = 35 mA typical, 50 System. 2. 3OIP measured with two tones at an output power of -1 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit. Gain vs. Frequency S11, S22 vs. Frequency S11, S22 (dB) 14 12 10 -5 100 -10 -20 -25 -30 1000 -40C +85C 1500 2000 Frequency (MHz) 2500 25 3.5 NF (dB) OIP3 (dBm) 1 2 3 4 5 20 15 1500 2000 Frequency (MHz) 1.0 3000 3 2 500 3.0 4.0 P1dB vs. Frequency 14 12 10 +85C 2500 2.0 Vde (V) 16 2.5 1000 0 0.0 6 Noise Figure vs. Frequency 4 -40C 40 Frequency (GHz) OIP3 vs. Frequency +25C +25C 60 20 0 3000 80 S11 -40 30 10 500 S22 -15 -35 +25C 8 500 120 P1dB (dBm) Gain (dB) 16 Vde vs. Icc 0 Icc (mA) 18 1000 1500 Frequency (MHz) 2000 8 500 +25C 1000 -40C 1500 2000 Frequency (MHz) +85C 2500 3000 Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 2 of 4 April 2006 ECG004 The Communications Edge TM InGaP HBT Gain Block Product Information Recommended Application Circuit Vcc Icc = 35 mA R4 Bias Resistor C4 Bypass Capacitor C3 0.018 F L1 RF Choke RF IN RF OUT ECG004 C2 Blocking Capacitor C1 Blocking Capacitor Reference Designator L1 C1, C2, C4 50 820 nH .018 F Recommended Component Values Frequency (MHz) 500 900 1900 2200 220 nH 68 nH 27 nH 22 nH 1000 pF 100 pF 68 pF 68 pF Recommended Bias Resistor Values 2500 18 nH 56 pF 3500 15 nH 39 pF Supply Voltage R1 value Size 5V 6V 8V 9V 10 V 12 V 45.7 ohms 74.3 ohms 131 ohms 160 ohms 189 ohms 246 ohms 0805 0805 1210 1210 2010 2010 1. The proper values for the components are dependent upon the intended frequency of operation. 2. The following values are contained on the evaluation board to achieve optimal broadband performance: Ref. Desig. L1 C1, C2 C3 C4 R4 Value / Type 39 nH wirewound inductor 56 pF chip capacitor 0.018 F chip capacitor Do Not Place 45.3 1% tolerance Size 0603 0603 0603 The proper value for R1 is dependent upon the supply voltage and allows for bias stability over temperature. WJ recommends a minimum supply bias of +5 V. A 1% tolerance resistor is recommended. 0805 Typical Device S-Parameters S-Parameters (Vdevice = +3.4 V, ICC = 35 mA, T = 25 C, calibrated to device leads) Freq (MHz) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) -30.10 -31.20 -28.45 -23.62 -19.37 -16.79 -14.66 -12.59 -10.75 -8.99 -7.43 -6.05 -4.96 177.98 178.03 -160.53 -166.34 176.50 155.39 135.92 114.48 95.65 77.47 62.98 49.23 37.32 17.55 17.28 16.78 16.22 15.77 15.17 14.46 13.72 12.93 12.01 11.08 10.00 8.98 177.81 158.24 138.41 119.90 102.19 84.04 66.94 49.78 33.56 17.53 2.33 -12.12 -25.64 -19.87 -19.74 -19.41 -19.00 -18.38 -18.05 -17.64 -17.38 -17.22 -17.17 -17.21 -17.44 -17.72 -0.31 -2.46 -5.05 -9.45 -14.50 -21.06 -27.87 -35.91 -43.77 -52.19 -61.28 -69.75 -77.89 -39.30 -28.23 -21.58 -17.50 -14.46 -12.24 -10.51 -9.02 -7.58 -6.36 -5.29 -4.29 -3.45 -168.77 -118.21 -132.33 -151.05 -171.81 167.01 147.79 129.31 112.01 95.56 81.52 68.48 55.77 Device S-parameters are available for download off of the website at: http://www.wj.com Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 3 of 4 April 2006 ECG004 The Communications Edge TM InGaP HBT Gain Block Product Information ECG004B-G Mechanical Information This package is lead-free/Green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both lead-free (maximum 260 C reflow temperature) and leaded (maximum 245 C reflow temperature) soldering processes. Outline Drawing Product Marking The component will be marked with an "E004G" designator with an alphanumeric lot code on the top surface of the package. The obsolete tin-lead package is marked with an "E004" designator followed by an alphanumeric lot code; it may also have been marked with a "D" designator followed by a 3-digit numeric lot code. Tape and reel specifications for this part are located on the website in the "Application Notes" section. MSL / ESD Rating Land Pattern ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 3 at +260 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135") diameter drill and have a final plated thru diameter of .25 mm (.010"). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contact the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 4 of 4 April 2006