MICROCIRCUIT DATA SHEET Original Creation Date: 09/20/96 Last Update Date: 09/11/98 Last Major Revision Date: 12/05/97 MN54ABT16374-X REV 0B0 16-BIT D FLIP-FLOP WITH TRI-STATE OUTPUTS General Description The ABT16374 contains sixteen non-inverting D flip-flops with TRI-STATE outputs and is intended for bus oriented applications. The device is byte controlled. A buffered clock (CP) and Output Enable (OE) are common to each byte and can be shorted together for full 16-bit operation. Industry Part Number NS Part Numbers 54ABT16374 54ABT16374W-QML Prime Die NB6374 Controlling Document 5962-9320101QXA Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 Features - Separate control logic for each byte 16-bit version of the ABT374 Edge-triggered D-type inputs Outputs sink capability of 48 mA, source capability of 24 mA High impedance glitch free bus loading during entire power up and power down cycle. Non-Destructive hot insertion capability. 2 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 (Absolute Maximum Ratings) (Note 1) Vcc Pin Potential to Ground Potential -0.5V to +7.0V Input Voltage (Note 2) -0.5V to +7.0V Input Current (Note 2) -30mA to +5.0mA Voltage Applied To Any Output In the Disabled or Power-Off State In The High State Current Applied To Output In The Low State (Max) Junction Temperature (Tj) Ceramic Thermal Resistance Junction-To-Case (Theta JC) Ceramic 48 Pin Flatpack Junction-To-Ambient (Theta JA) (1 Watt at no airflow) Ceramic 48 Pin Flatpack Storage Temperature -0.5V to 5.5V -0.5V to Vcc 96mA +175C 20 C/Watt 80 C/Watt -65C to +150C Lead Temperature (Soldering, 10 seconds) ESD Classification +300C Class 2 Maximum Power Dissipation 500 mW Note 1: Note 2: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Either voltage limit or current limit is sufficient to protect inputs. Recommended Operating Conditions Supply Voltage (Vcc) 4.5V to 5.5V Operating Temperature -55C to +125C Minimum Input Edge Rate (dV/dt) Data Input Enable Input Maximum Output Current High Level (Ioh) Low Level (Iol) 50 mV/ns 20 mV/ns -24 mA 48 mA 3 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: 4.5V to 5.5V Temp Range: -55C to 125C SYMBOL PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS ICCH Supply Current VCC=5.5V, VINH=5.5V, VINL=0.0V 1, 4 VCC 2.0 mA 1, 2, 3 ICCL Supply Current VCC=5.5V, VINH=5.5V, VINL=0.0V 1, 4 VCC 62.0 mA 1, 2, 3 ICCZ Supply Current VCC=5.5V, VINH=5.5V, VINL=0.0V 1, 4 VCC 2.0 mA 1, 2, 3 ICCT Supply Current per Input VCC=5.5V, OE=0.0V Input under test=3.4V Other inputs=5.5V or 0.0V 1, 4 VCC 2.5 mA 1, 2, 3 VCC=5.5V, OE=3.4V Other inputs=5.5V or 0.0V 1, 4 VCC 2.5 mA 1, 2, 3 IIH High Level Input Current VCC=5.5V, VINH=5.5V 1, 4 IN 2.0 uA 1, 2, 3 IIL Low Level Input Current VCC=5.5V, VINL=0.0V 1, 4 IN -2.0 uA 1, 2, 3 IOZH Maximum TRI-STATE Leakage Current HIGH VCC=5.5V, VOUT=2.7V VINL=0.0V, VIH (OE)=2.0V 1, 4 OUT 50.0 uA 1, 2, 3 IOZL Maximum TRI-STATE Leakage Current LOW VCC=5.5V, VOUT=0.5V VINH=5.5V, VIH (OE)=2.0V 1, 4 OUT -50.0 uA 1, 2, 3 ICEX Output High Leakage Current VCC=5.5V, VOUT=5.5V VINH=5.5V 1, 4 OUT 50.0 uA 1, 2, 3 IOS Output Short Circuit Current VCC=5.5V, VOUT=0.0V VINH=5.5V 1, 4, 10 OUT -100 -275 mA 1, 2, 3 IOS1 Output Short Circuit Current VCC=5.5V, VOUT=2.5V VINH=5.5V 1, 4, 10 OUT -50 -180 mA 1, 2, 3 IBVI Input High Current Breakdown Test VCC=5.5V, VINH=7.0V 1, 4 IN 7.0 uA 1, 2, 3 IZZ Bus Drainage Test VCC=0.0V, VOUT=5.5V, VINL=0.0V 1, 4 IN/OUT 100 uA 1, 2, 3 VOL Low Level Output Voltage VCC=4.5V, IOL=48.0mA, VINH=4.5V, VINL=0.0V, VIH=2.0V, VIL=0.8V 1, 4 OUT 0.55 V 1, 2, 3 VOH High Level Output Voltage VCC=4.5V, IOH=24.0mA, VINH=4.5V, VINL=0.0V, VIH=2.0V, VIL=0.8V 1, 4 OUT 2.0 V 1, 2, 3 VCC=4.5V, IOH=-3mA, VINH=4.5V, VINL=0.0V, VIH=2.0V, VIL=0.8V 1, 4 OUT 2.5 V 1, 2, 3 VCC=5.0V, IOH=-3mA, VINH=5.0V, VINL=0.0V, VIH=2.0V, VIL=0.8V 1, 4 OUT 3.0 V 1, 2, 3 4 -100 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: 4.5V to 5.5V Temp Range: -55C to 125C SYMBOL PARAMETER CONDITIONS NOTES PINNAME VID Input Leakage Test VCC=0.0V, IID=1.9uA, VINL=0.0V 1, 4 IN VCD Input Clamp Diode Voltage VCC=4.5V, IKL=-18mA, VINH=4.5V, VINL=0.0V 1, 4 IN VOLP Low Level Ground Bounce VCC=5.0V, LOAD : 50pF / 500 OHMS VOLV Low Level Ground Bounce VOHP MIN MAX SUBGROUPS V 1, 2, 3 -1.2 V 1, 2, 3 7, 8 OUT 0.88 V 4 VCC=5.0V, LOAD : 50pF / 500 OHMS 7, 8 OUT -1.5 V 4 High Level VCC Bounce VCC=5.0V, LOAD : 50pF / 500 OHMS 7, 8 OUT 1.375 V 4 VOHV High Level VCC Bounce VCC=5.0V, LOAD : 50pF / 500 OHMS 7, 8 OUT -0.8 V 4 CIN Input Capacitance VCC=0.0V 7 IN 10.5 pF 4 COUT Output Capacitance VCC=5.0V 7 OUT 14.5 pF 4 5 4.75 UNIT MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 Electrical Characteristics AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF RL=500 OHMS TRISE/TFALL = 3.0nS SYMBOL tpLH tpHL tpZL tpZH tpHZ tpLZ PARAMETER Propagation Delay Propagation Delay Output Enable Time Output Enable Time Output Disable Time Output Disable Time CONDITIONS NOTES VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C PINNAME MIN MAX UNIT SUBGROUPS 2, 5 CP to On 1.5 5.7 ns 9 2, 5 CP to On 1.5 6.9 ns 10, 11 2, 5 CP to On 1.5 6.1 ns 9 2, 5 CP to On 1.5 6.9 ns 10, 11 2, 5 OE to On 1.6 5.9 ns 9 2, 5 OE to On 1.2 6.5 ns 10, 11 2, 5 OE to On 1.2 5.9 ns 9 2, 5 OE to On 0.8 6.5 ns 10, 11 2, 5 OE to On 1.5 8.6 ns 9 2, 5 OE to On 1.5 9.6 ns 10, 11 2, 5 OE to On 1.5 6.2 ns 9 2, 5 OE to On 1.5 7.2 ns 10, 11 ts (H/L) Setup Time HIGH or LOW VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 7 Dn to CP 1.3 ns 9, 10, 11 th (H/L) Hold Time HIGH or LOW VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 7 Dn to CP 1.5 ns 9, 10, 11 tw (H) Pulse Width VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 7 CP 3.3 ns 9, 10, 11 Fmax Maximum Clock Frequency VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 7 CP 150 MHz 9, 10, 11 Note 1: Screen tested 100% on each device at -55C, +25C & +125C Temp., Subgroups 1,2,3,7 & 8. Note 2: Screen tested 100% on each device at -55C, +25C, and +125C temp., subgroups A9, A10, and A11. Screen tested 100% on each device at +25C temp. only, subgroup A9. Sample tested (Method 5005, Table 1) on each mfg. lot at +25C, +125C, & -55C temp. subgroups A1, 2, 3, 7 & 8. Sample tested (Method 5005, Table 1) on each mfg. Lot at +25C, +125C & -55C temp., subgroups A9, 10 & 11. Sample tested (Method 5005, Table 1) on each mfg. Lot at 25C temp only, subgroup A9. Not tested (Guaranteed by Design Characterization Data). Max number of outputs defines as (N). N-1 data inputs are driven 0V to 3V. one output @Vol or @Voh. Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: 6 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 (Continued) Note 9: Max number of data inputs (N) switching. (N-1) inputs switching 0V to 3V. Input-under-test switching : 3V to threshold (Vild), 0V to threshold (Vihd), Freq= 1 MHZ Note 10: Maximum test duration not to exceed one second, not more than one output shorted at one time. 7 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 Graphics and Diagrams GRAPHICS# WA48ARB DESCRIPTION CERPACK, 48 LEAD, .025 LEAD PITCH (P/P DWG) See attached graphics following this page. 8 MICROCIRCUIT DATA SHEET MN54ABT16374-X REV 0B0 Revision History Rev ECN # Originator Changes 0A0 M0000446 09/11/98 Rel Date Bill Petcher Initial MDS Release 0B0 M0002952 09/11/98 Linda Collins New update:: MN54ABT16374-X Rev. 0B0. Changed ns to MHz in the AC FMax unit column. 9