May 2017
INDUCTORS
Multilayer Ferrite
MLZ2012 2012 [0805 inch]*
* Dimensions Code JIS[EIA]
Inductors for Decoupling Circuits
MLZ2012
Type
MLZ Series
(2/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
INDUCTORS
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
Inductors for Decoupling Circuits
Multilayer Ferrite
FEATURES
The MLZ Series include inductors for decoupling circuits that have top-class DC superimposition characteristics and low DC resistance.
They are compatible with wide frequency band noise, from low to high frequency.
H type products have a rated current that is equivalent to that of wound coils.
W type products are the new standard type products that have both large current and low resistance.
L type products have a resistance up to 60% lower than W type products.
APPLICATION
Smart phones, tablet terminals, note PCs, various modules such as camera modules, DSCs, video games, portable memory audio
devices, navigation systems, PNDs, WLANs, SSDs
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
Overview of MLZ2012 Type
MLZ 2012 M 1R0 H T 000
Series name L×W×H Dimensions Product
internal code
Inductance Characteristic type Packaging style Internal code
(mm) (µH)
2012 2.0×1.25×0.85 A 1R0 1 H Ultra-large current type T Taping 000
2.0×1.25×1.25 D 100 10 D High frequency type
M 101 100 W Large current type
N L Low resistance type
Type
Temperature range Package quantity Individual weight
Operating
temperature
（°C）
Storage
temperature
（°C）(pieces/reel) （mg）
MLZ2012 t=0.85 –55 to +125 –55 to +125 4000 10
t=1.25 2000 14
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
T
0.85±0.20
1.25±0.20
2.00±0.20
T 1.25±0.20
0.50±0.30 0.50±0.30
Dimensions in mm
(6/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
1Current assumed when inductance ratio has decreased by 50% max..
2Current assumed when temperature has risen to 20°C max. (reference value).
Operating temperature environment at this time: 105°C max.
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Type LThickness L measuring conditions DC resistance Isat1Itemp2Part No.
TFrequency Current
(µH) Tolerance (mm) (MHz) (mA) ()±30% (mA) (mA)
Ultra-large
current
1.0 ±20% 1.25 2 0.1 0.10 700 800 MLZ2012M1R0HT000
1.5 ±20% 1.25 20.1 0.14 550 700 MLZ2012M1R5HT000
2.2 ±20% 1.25 2 0.1 0.16 400 600 MLZ2012M2R2HT000
3.3 ±20% 1.25 20.1 0.20 350 500 MLZ2012M3R3HT000
4.7 ±20% 1.25 2 0.1 0.34 300 400 MLZ2012M4R7HT000
6.8 ±20% 1.25 20.1 0.40 220 350 MLZ2012M6R8HT000
10 ±20% 1.25 2 0.1 0.68 200 300 MLZ2012M100HT000
High
frequency
0.10 ±20% 0.85 25 1.0 0.07 1000 1150 MLZ2012DR10DT000
0.22 ±20% 0.85 25 1.0 0.13 800 900 MLZ2012DR22DT000
0.47 ±20% 1.25 25 1.0 0.18 550 700 MLZ2012DR47DT000
Large current
1.00 ±20% 0.85 10 1.0 0.10 280 900 MLZ2012A1R0WT000
1.50 ±20% 0.85 10 1.0 0.13 250 750 MLZ2012A1R5WT000
2.20 ±20% 0.85 10 1.0 0.15 210 650 MLZ2012A2R2WT000
3.30 ±20% 0.85 10 1.0 0.34 200 450 MLZ2012A3R3WT000
4.70 ±20% 0.85 2 0.1 0.30 180 500 MLZ2012M4R7WT000
6.80 ±20% 1.25 20.1 0.40 160 400 MLZ2012M6R8WT000
10.0 ±20% 1.25 2 0.1 0.47 150 350 MLZ2012M100WT000
15.0 ±20% 1.25 20.1 0.95 120 250 MLZ2012M150WT000
22.0 ±20% 1.25 2 0.1 1.25 100 220 MLZ2012P220WT000
22.0 ±20% 1.25 20.1 2.0 60 220 MLZ2012M220WT000
33.0 ±20% 1.25 2 0.1 2.60 55 190 MLZ2012M330WT000
47.0 ±20% 1.25 20.1 3.70 50 170 MLZ2012M470WT000
Low
resistance
1.00 ±20% 0.85 2 0.1 0.06 220 1150 MLZ2012N1R0LT000
1.50 ±20% 0.85 20.1 0.10 190 900 MLZ2012N1R5LT000
2.20 ±20% 0.85 2 0.1 0.12 170 800 MLZ2012N2R2LT000
3.30 ±20% 0.85 20.1 0.15 130 750 MLZ2012N3R3LT000
4.70 ±20% 0.85 2 0.1 0.18 130 600 MLZ2012N4R7LT000
6.80 ±20% 0.85 20.1 0.25 110 550 MLZ2012N6R8LT000
10.0 ±20% 1.25 2 0.1 0.30 110 500 MLZ2012N100LT000
15.0 ±20% 1.25 20.1 0.47 90 350 MLZ2012N150LT000
22.0 ±20% 1.25 2 0.1 0.67 70 300 MLZ2012N220LT000
100.0 ±20% 1.25 20.1 3.50 30 140 MLZ2012N101LT000
Measurement item Product No. Manufacturer
L 4294A+16034G Keysight Technologies
DC resistance Type-7561 Yokogawa
(7/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
L FREQUENCY CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.1
1
100
10
M1R0H
M1R5H
M2R2H
M3R3H
M4R7H
M6R8H
M100H
Product No. Manufacturer
E4991A+16192ＡKeysight Technologies
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
1000
100
10
DR10D
DR22D
DR47D
Product No. Manufacturer
E4991A+16192A Keysight Technologies
(8/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
1000
100
10
M100W
M150W
M220W
P220W
M330W
M470W
A1R0W
A1R5W
A2R2W
A3R3W
M4R7W
M6R8W
Product No. Manufacturer
E4991A+16192ＡKeysight Technologies
(9/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
1 10 100 1000
Inductance(μH)
Frequency(MHz)
0.01
0.1
1
1000
100
10
N1R0L
N1R5L
N2R2L
N3R3L
N4R7L
N6R8L
N100L
N150L
N220L
N101L
Product No. Manufacturer
E4991A+16192ＡKeysight Technologies
(10/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
DC current(mA)
Inductance(μH)
0.1
1
10
100
200 400 600 800 1000
M1R0H
M1R5H
M2R2H
M3R3H
M4R7H
M6R8H
M100H
Product No. Manufacturer
4291B+16200A+16192A Keysight Technologies
0
DC current(mA)
Inductance(μH)
0.01
0.1
1
10
200 400 600 800 1000
DR10D
DR22D
DR47D
Product No. Manufacturer
4291B+16200A+16192A Keysight Technologies
(11/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
0
DC current(mA)
Inductance(μH)
0.1
1
10
100
1000
100 200 300 400 500 600 700
M100W
M470W
M4R7W
P220W
M330W
M6R8W
M220W M150W
A1R5W
A1R0W
A2R2W
A3R3W
Product No. Manufacturer
4291B+16200A+16192A Keysight Technologies
0
DC current(mA)
Inductance(μH)
0.1
1
10
100
1000
100 200 300 400 500
N1R0L
N220L
N101L
N150L
N3R3LN4R7L
N6R8L
N100L
N1R5L
N2R2L
Product No. Manufacturer
4291B+16200A+16192A Keysight Technologies
(12/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH H CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH D CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
M1R0H
M1R5H
M2R2H
M3R3H
M4R7H
M6R8H
M100H
Product No. Manufacturer
E4991A+16192A Keysight Technologies
110 1000100
1
100
1000
10000
10
Impedance(Ω)
Frequency(MHz)
DR10D
DR22D
DR47D
Product No. Manufacturer
E4991A+16192A Keysight Technologies
(13/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH W CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
1000000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
M150W
M220W
P220W
M330W
M470W
A1R0W
M6R8W
A1R5W
A2R2W
M4R7W
A3R3W
M100W
Product No. Manufacturer
E4991A+16192A Keysight Technologies
(14/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH L CHARACTERISTIC PRODUCT
○Measurement equipment
＊ Equivalent measurement equipment may be used.
110 1000100
1
100
1000
100000
10000
10
Impedance(Ω)
Frequency(MHz)
N1R0L
N220L
N101L
N3R3L
N2R2L
N1R5L
N4R7L
N6R8L
N100L
N150L
Product No. Manufacturer
E4991A+16192A Keysight Technologies
(15/15)
20170510 / inductor_commercial_decoupling_mlz2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MLZ2012 Type
PACKAGING STYLE
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
Typ e ABK
MLZ2012 t=0.85 1.5±0.2 2.3±0.2 1.1 max.
t=1.25 1.5±0.2 2.3±0.2 1.5 max.
B
A
8.0±0.3
F 1.75±0.1
4.0±0.1
4.0±0.1
2.0±0.05
1.5 +0.1
0
KK
MLZ2012 (t=1.25)MLZ2012 (t=0.85)
Dimensions in mm
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm