STEVAL-CBP005V1 Front panel demonstration board based on the STLED316S Data Brief Features 16 x 3 mm blue LEDs for status and function indication 2 x 5 mm BiColor LEDs 12 front panel function keys 1 reset button on rear Provision for mounting IR sensor and associated bias components 11-pin connector termination for easy interface to host All data and power lines and additional signals available on connector STEVAL-CBP005V1 Description The STEVAL-CBP005V1 demonstration board functions as a front panel solution for the HR21 set-top box (STB), and is designed to allow testing of the versatile LED controller/driver STLED316S. The HR21 main board serves as the host (master), and the STEVAL-CBP005V1 demonstration board functions as a slave. The interface is an 11-pin connector cable, which provides all required device control signals, the 3.3 and 5 V supply, the reset and IR sensor data lines, and ground. The board also provides all necessary function switches as well as LEDs for function/status indication. The STEVAL-CBP005V1 demonstration board must be connected to the host to function properly. Factory testing was completed using a test jig, which emulated the host. June 2008 Rev 1 For further information contact your local STMicroelectronics sales office. 1/4 www.st.com 4 DIG2 2/4 L9 L1 L14 L1 L13 L1 L12 L1 L11 L1 L10 DIG3 5V 9 L1 L18 L1 L17 L1 L16 L1 L15 SEG8/KS SE KS8 SEG7/KS SE KS7 SEG6/KS SE KS6 SEG5/KS SE KS5 SEG4/KS SE KS4 SEG3/KS SE KS3 SEG2/KS SE KS2 SEG1/KS SE KS1 R5 360 36 24 C2 0.1u 1uF/25 25V GND 17 4 2 3 1 21 20 19 18 16 15 14 13 480i 480 L1 REC/MODEM L5 3.3V 3.3V PWR/STBY L6 R1 1K R2 10 10K SEG1/KS1 SEG2/KS2 SEG3/KS3 SEG4/KS4 SEG5/KS5 SEG6/KS6 SEG7/KS7 SEG8/KS8 IRQ_N CLK STB DIN/DOUT EY1 23 KEY EY2 22 KEY LED_DISPLAY_SECTION IRQ-N CLK STB DIN/DOUT STLED3168_ 3168_SO_2 _24 SET DIG1_L 1_LED KEY1 DIG2 KEY2 DIG3 DIG4 SEG1/K /KS1 DIG5 SEG2/K /KS2 DIG6 SEG3/K /KS3 DIG7 SEG4/K /KS4 VCC SEG5/K /KS5 SEG6/K /KS6 SEG7/K /KS7 SEG8/K /KS8 GND U1 R4 10k 10 480P 480 L2 D6 D5 D4 D3 D2 D1 720p 720 L3 KEY1 KEY KEY2 KEY SW9 MENU 1080i 1080 L4 SW5 SW1 SW10 SW6 SEG6/KS SE KS6 SEG5/KS SE KS5 SEG8/KS SE KS8 SEG7/KS SE KS7 SE KS1 SEG1/KS SEG2/KS SE KS2 SEG3/KS SE KS3 SEG4/KS SE KS4 DIG1_L 1_LED SELECT SE SW2 REC SW7 SW3 SW11 ACTIVE KEY_MATRIX SECTION INFO CON3 IR 3 2 1 SW12 POWER RESO R6 47 RESE SET RESET_ SECTION IR_OUT 47u 47uF C3 5V I R_ S E NS OR_ S E CT I ON SW8 SW4 RESE SET R8 12K 12 3.3V R7 10k 10 3.3V CON1 J6 CON1 J5 CON1 J4 CON1 J3 DIN/DOUT CLK STB IRQ_N IR_OUT RESE SET GND 5V GND 3.3V TP1 TES EST POINT 1 2 3 4 5 6 7 8 9 10 11 CON11 J2 S I GNA L _ P OWE R_ HE A DE R 1 1 1 1 Figure 1. L8 L7 C1 33uF/25 33u 25V 5V DIG1_L 1_LED 5 DIG2 6 DIG3 7 8 10 11 12 R3 10 10k GUIDE 1 1 LED_DRIVER_ SECTION Board schematic STEVAL-CBP005V1 Board schematic Schematic diagram STEVAL-CBP005V1 2 Revision history Revision history Table 1. Document revision history Date Revision 24-Jun-2008 1 Changes Initial release. 3/4 STEVAL-CBP005V1 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 4/4