Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC987LP5E Evaluation Kit Analog, Digital & Mixed-Signal ICs, Modules, Subsystems & Instrumentation User Manual Software & Hardware Installation Order On-Line at: www.hittite.com Receive the latest product releases - click on "My Subscription" 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * sales@hittite.com Part # 140-00037-00 Rev. B - v01.0711 ECN# CP111107 HMC987LP5E Evaluation Kit User Manual Rev. B - v01.0711 Table of Contents 1. 2. 2.1 2.2 3. 4. 4.1 4.2 4.2.1 4.2.2 4.2.2.1 4.3 4.3.1 4.3.2 5. 5.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Setup and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 User Provided Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Parallel Port Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SPI Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Evaluation Board Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Single-Ended Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Single-Ended Output Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using the HMC987LP5E Evaluation Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 HMC987LP5E GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Notice Hittite Microwave Corporation has prepared this manual for use by Hittite personnel and customers as a guide for the proper installation, operation, and maintenance of Hittite equipment and computer programs. The drawings, specifications, and information contained herein are the property of Hittite Microwave Corporation, and any unauthorized use or disclosure of these drawings, specifications, and information is prohibited; they shall not be reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the equipment or software programs without the prior written consent of Hittite Microwave Corporation. 2 Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com Rev. B - v01.0711 HMC987LP5E Evaluation Kit User Manual 1. Introduction This document describes the functionality of the HMC987LP5E Evaluation Kit. The HMC987LP5E Evaluation board can be controlled via parallel port or SPI (Serial Port Interface). Parallel port control is implemented by simple jumper settings on the evaluation board. Serial Port interface offers more flexibility. This HMC987LP5E Evaluation Kit also includes the PC compatible software with Graphical User Interface (GUI), and software drivers necessary for Serial Port Interface, allowing the user to read from and write to all device registers, set gain levels and save & recall device configurations. Note: For most up-to-date software download and information please visit www.hittite.com. 2. Package Contents 2.1 Hardware Verify that all the items listed in Table 1 are included in the shipment. Item Quantity HMC987LP5E Evaluation Board 1 USB Interface Board 1 6' USB A Male to USB B Male Cable 1 CD ROM (Contains User Manual and software) 1 Table 1: Packing List 2.2 Software The HMC987LP5E Evaluation Software enables users to communicate with and control HMC987LP5E Evaluation Board with their PC, and observe full functionality and performance of the HMC987LP5E. 3. Operating Environment This evaluation kit is designed for use in a laboratory setting at ambient room temperature (25C) and is not protected against moisture. The USB Interface Board has an ESD rating of +/-3000V, however the HMC987LP5E may have a lower rating (check the product's datasheet for its specific ESD rating). Use appropriate ESD procedures and precautionary measures when handling all electronic hardware. 4. Setup and Installation 4.1 User Provided Equipment In addition to the items provided in the evaluation kit, the user must provide the following equipment to communicate with the device under test. * DC Power Supply * DC Cables * Signal source Generator * Computer (PC) with Standard USB port if SPI control of the HMC987LP5E is desired. For detail specifications regarding operating system and software requirements please visit www.hittite.com Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com 3 Rev. B - v01.0711 HMC987LP5E Evaluation Kit User Manual 4.2 Hardware Setup The HMC987LP5E can be controlled via the parallel port or the SPI (Serial Port Interface). More information is available in the HMC987LP5E datasheet. 4.2.1 Parallel Port Control Setup Setup all hardware according to Figure 1. * Apply 4 V to 5 V to TP1 (TP2 is GND) on HMC987LP5E eval board. Supply current should be ~390 mA. * Ensure jumper J7 is off, to enable parallel mode of the HMC987LP5E (PMODE_SEL = 1). * Any enabled outputs that are not used should be terminated with a 50 termination to ground. * Jumpers J5 (SCLK), J6 (SDI), and J10 (SEN) are used to enable individual LVPECL outputs according to the following truth table: Table 2. HMC987LP5E Parallel Port Output Control Truth Table SCLK, SDI, SEN Enabled Outputs 000 OUT2 001 OUT2 + OUT7 010 OUT2 + OUT7 + OUT4 011 OUT2 + OUT7 + OUT4 + OUT6 100 OUT2 + OUT7 + OUT4 + OUT6 + OUT5 + OUT5 101 OUT2 + OUT7 + OUT4 + OUT6 + OUT5 + OUT5 + OUT3 110 OUT2 + OUT7 + OUT4 + OUT6 + OUT5 + OUT5 + OUT3 + OUT8 111 OUT2 + OUT7 + OUT4 + OUT6 + OUT5 + OUT5 + OUT3 + OUT8 + OUT1 Note that jumper ON pulls the signal to ground (0 V). * The RF Buffer Enable is controlled from jumper J9. Installing the jumper pulls the enable to 0 - disabling the buffer. If the jumper is open, the buffer is enabled at maximum gain. Note that the HMC987LP5E evaluation board includes a very low noise HMC987LP3E regulator. It is programmed (via resistors) to take in a voltage from 4.0 V to 5 V and generate the 3.3 V required for the HMC987LP5E. 4 Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com Rev. B - v01.0711 HMC987LP5E Evaluation Kit User Manual SLCK SDI Parallel Control SEN Figure 1. HMC987LP5E Eval Board Parallel Port Control Test Setup 4.2.2 SPI Control Setup all hardware according to Figure 2. * Connect the USB board to HMC987LP5E eval board. * Connect the USB cable to USB board. * Apply 4 V to 5 V to TP1 (TP2 is GND) on HMC987LP5E eval board. Supply current should be ~395 mA. * Use a jumper on J7 to disable Parallel Mode of the HMC987LP5E. * Any enabled outputs that are not used should be terminated with a 50 termination to ground. Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com 5 HMC987LP5E Evaluation Kit User Manual Rev. B - v01.0711 Figure 2. HMC987LP5E Eval Board SPI Control Test Setup 4.2.2.1 Software Installation Note: Installing/Uninstalling the HMC987LP5E Evaluation Software requires administrative privileges To install/uninstall HMC987LP5E Evaluation Software, double click on "HMC987LP5E Eval Software Installer.exe" that was downloaded from www.hittite.com, or provided with a CD, and follow the installation/ uninstallation wizard. 6 Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com Rev. B - v01.0711 HMC987LP5E Evaluation Kit User Manual 4.3 Evaluation Board Configuration The HMC987LP5E Evaluation Board schematic shows various input/output configurations. Default configurations are populated, and optional ones (labeled `depop') are not populated. HMC987LP5E evaluation board is configured for differential drive, with AC coupling on both the input and output, by default. Components that are not populated on the HMC987LP5E evaluation board are not included in the evaluation kit. For low frequency signals ( < 500 MHz) the 100 pF DC blocking capacitors on input and output should be increased. Detailed information about various input/output HMC987LP5E interface configuration options are available in the HMC987LP5E datasheet. 4.3.1 Single-Ended Input Configuration Hardware evaluation board changes are required to configure the HMC987LP5E evaluation board for single-ended input operation. To configure HMC987LP5E evaluation board for single-ended input operation simply populate C104 with a 1 nF capacitor, and remove C12. Drive input CLKP (J1), and CLKN (J2) is AC grounded. 4.3.2 Single-Ended Output Configuration When measuring single-ended, ensure that the other unused output is terminated with 50 to ground. 5. Using the HMC987LP5E Evaluation Software 1. Ensure that the USB interface hardware is connected to the evaluation board, and that the HMC987LP5E is powered. 2. Launch HMC987LP5E Evaluation Software by selecting on "Hittite BUFFER Eval Software Vx.exe" from the Program Files menu of your computer. The main window should open. See Figure 3 below. Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com 7 HMC987LP5E Evaluation Kit User Manual Rev. B - v01.0711 Figure 3. HMC FANOUT BUFFER Control Software 3. From this window select the HMC987LP5E from the drop down menu and press "Done" and the following window appears. 8 Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com Rev. B - v01.0711 HMC987LP5E Evaluation Kit User Manual Figure 4. HMC987LP5E Main GUI This interface allows the user: * To save and load HMC987LP5E register configurations. * To open an existing register configuration file use the "Load Register File" button. * To save a register configuration to a file use the "Save Register File" button. This allows you to instantly recall the desired register state by using the " Load Register File" button. Click on `Open HMC987LP5E GUI.' 5.1 HMC987LP5E GUI The HMC987LP5E GUI (Figure 5) allows the user: * Enable/disable individual buffers (LVPECL outputs) * Read the chip ID * Select input impedance * Adjust output RF buffer settings including gain settings Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com 9 HMC987LP5E Evaluation Kit User Manual Rev. B - v01.0711 Figure 5. Register Settings 10 Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com Rev. B - v01.0711 HMC987LP5E Evaluation Kit User Manual 5.2 Direct Register Access * "Direct SPI Access" button in the `HMC987LP5E Main GUI' provides direct register read/write capability (Figure 6). Figure 6. Direct SPI Access 6. Technical Support Please contact apps-support@hittite.com for any questions. Hittite Microwave provides local direct support in many areas around the world. Please see the "Contact Us" page at www.hittite.com. Order On-Line: www.hittite.com. For technical application questions: Tel: 978-250-3343 or apps-support@hittite.com 11 Order On-Line at: www.hittite.com Receive the latest product releases - click on "My Subscription" 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 * Fax: 978-250-3373 * sales@hittite.com