ACSL6420 - Agilent / Hewlett-Packard

Agilent ACSL-6xx0

Multi-Channel and Bi-Directional,

15 MBd Digital Logic Gate Optocoupler

Data Sheet

Description

ACSL-6xx0 are truly isolated,

multi-channel and bi-directional,

high-speed optocouplers. Integra-

tion of multiple optocouplers in

monolithic form is achieved

through patented process tech-

nology. These devices provide full

duplex and bi-directional iso-

lated data transfer and communi-

cation capability in compact

surface mount packages. Avail-

able in 15 Mbd speed option and

wide supply voltage range.

These high channel density make

them ideally suited to isolating

data conversion devices, parallel

buses and peripheral interfaces.

They are available in 8-pin and

16–pin narrow-body SOIC

package and are specified over

the temperature range of

-40°C to +100°C.

Features

• Available in dual, triple and quad

channel configurations

• Bi-directional

• Wide supply voltage range

3.0V to 5.5V

• High-speed: 15 MBd typical,

10 MBd minimum

• 10 kV/µs minimum Common Mode

Rejection (CMR) at Vcm = 1000 V

• LSTTL/TTL compatible

• Safety and regulatory approvals

(Pending)

– 2500Vrms for 1 min per UL1577

– CSA Component Acceptance

– IEC/EN/DIN EN 60747-5-2

• 16 Pin narrow-body SOIC package

for triple and quad channel

• -40 to 100°C temperature range

CAUTION:

It is advised that normal static precautions be taken in handling and

assembly of this component to prevent damage and/or degradation,

which may be induced by ESD.

Applications

• Full duplex communication

• Isolated line receiver

• Computer-peripheral interfaces

• Microprocessor system interfaces

• Digital isolation for A/D and D/A

conversion

• Switching power supply

• Instrument input/output isolation

• Ground loop elimination

• Pulse transformer replacement

Device Selection Guide

Device Number Channel Configuration Package

ACSL-6210 Dual, Bi-Directional` 8-pin Small Outline

ACSL-6300* Triple, All-in-One 16-pin Small Outline

ACSL-6310* Triple, Bi-Directional, 2/1 16-pin Small Outline

ACSL-6400 Quad, All-in-One 16-pin Small Outline

ACSL-6410* Quad, Bi-Directional, 3/1 16-pin Small Outline

ACSL-6420* Quad, Bi-Directional, 2/2 16-pin Small Outline

* Advanced Information

Pin Description

Symbol Description Symbol Description

VDD1 Power Supply 1 GND1Power Supply Ground 1

VDD2 Power Supply 2 GND2Power Supply Ground 2

ANODExLED Anode NC Not Connected

CATHODExLED Cathode VOX Output Signal

Truth Table (Positive Logic)

LED OUTPUT

ON L

OFF H

Ordering Information

A C S L - 6 X X 0 - X Y Z E

Channel Configuration

(Refer to the Device

Selection Guide)

Lead Free Option

R = SO-8 Package, 100 units per tube

T = SO-16 Package, 50 units per tube

6 = IEC/EN/DIN EN 60747-5-2,

VIORM = 560V peak Option

5 = Tape and Reel Packaging Option,

1500 units per reel for SO-8 Package

and 1000 units per reel for SO-16 Package

Functional Diagrams

ACSL-6210 - Dual-Ch, Bi-Dir ACSL-6300 - Triple-Ch, All-in-One*

ACSL-6310 - Triple-Ch, Bi-Dir (2/1)* ACSL-6400 - Quad-Ch, All-in-One

ACSL-6410 - Quad-Ch, Bi-Dir (3/1)* ACSL-6420 - Quad-Ch, Bi-Dir (2/2)*

* Advanced Information

228

(

791

)

244

(

197

)

386

(

802

)

394

(

999

)

152

(

861

)

157

(

988

)

013

(

330

)

020

(

508

)

040

(

016

)

060

(

524

)

050

(

270

)

060

(

524

)

054

(

372

)

068

(

727

)

004

(

102

)

010

(

249

)

016

(

406

)

050

(

270

)

010

(

245

)

020

(

508

)

008

(

191

)

010

(

249

)

–

(

)

8765

0.228 (5.80)

0.244 (6.20)

0.189 (4.80)

0.197 (5.00)

0.150 (3.80)

0.157 (4.00)

0.013 (0.33)

0.020 (0.51)

0.040 (1.016)

0.060 (1.524)

0.004 (0.10)

0.010 (0.25)

0.054 (1.37)

0.069 (1.75)

0.016 (0.40)

0.050 (1.27)

0.008 (0.19)

0.010 (0.25)

0.020 (0.50)

x 45°

0°

8°

DIMENSIONS: INCHES (MILLIMETERS) MIN

MAX

ACSL-6210 Small Outline SO-8 Package

ACSL-6300*, ACSL-6310*, ACSL-6400, ACSL-6410* and

ACSL-6420* Small Outline SO-16 Package

Package Outline Drawings

TIME (SECONDS)

TEMPERATURE (°C)

200

100

50 150100 200 250

300

SEC.

50 SEC.

SEC.

160°C

140°C

150°C

PEAK

TEMP.

245°C

PEAK

TEMP.

240°C

PEAK

TEMP.

230°C

SOLDERING

TIME

200°C

PREHEATING TIME

150°C, 90 ± 30 SEC.

2.5°C ± 0.5°C/SEC.

3°C + 1°C/–0.5°C

TIGHT

TYPICAL

LOOSE

ROOM

TEMPERATURE

PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.

REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.

Solder Reflow Temperature Profile

Pb-free IR Profile

Regulatory Information

Insulation and Safety Related Specifications

Parameter Symbol Value Units Conditions

Minimum External Air Gap (Clearance) L(I01) 4.9 mm Measured from input terminals to output terminals,

shortest distance through air

Minimum Externa l Tracking(Creepage) L(I02) 4.5 mm Measured from input terminals to output terminals,

shortest distance path through body

Minimum Internal Plastic Gap (Internal Clearance) 0.08 mm Insulation thickness between emitter and detector;

also known as distance through insulation

Tracking Resistance (Comparative Tracking Index) CTI 175 Volts DIN IEC 112/VDE0303 Part 1

Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option X6X Only)

Description Symbol ACSL-6XX0-X6X Units

Installation Classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤150V rms I-IV

for rated mains voltage ≤300V rms I-III

Climatic Classification 55/100/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage VIORM 560 Vpeak

Input to Output Test Voltage, Method b * VPR 1050 Vpeak

VIORM x 1.875 = VPR, 100% Production

Test with tm = 1 sec, Partial Discharge < 5 pC

Input to Output Test Voltage, Method a * VPR 840 Vpeak

VIORM x 1.5 = VPR, Type and Sample Test,

Tm = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage * VIOTM 4000 Vpeak

(Transient Overvoltage, tini = 10 sec)

Safety Limiting Values

(Maximum values allowed in the event of a failure)

Case Temperature TS175 °C

Input Current IS,INPUT 150 mA

Output Power PS,OUTPUT 600 mW

Insulation Resistance at TS, VIO = 500V RIO 109Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2,

for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application.

Absolute Maximum Ratings

Parameter Symbol Min. Max. Units

Storage Temperature Ts-55 125 °C

Operating Temperature TA-40 100 °C

Supply Voltage (1 Minute Maximum) VDD1 , VDD2 7V

Reverse Input Voltage (Per Channel) VR5V

Output Voltage (Per Channel) VO7V

Average Forward Input Current[1] (Per Channel) IF15 mA

Output Current (Per Channel) IO50 mA

Input Power Dissipation[2] (Per Channel) P127 mW

Output Power Dissipation[2] (Per Channel) PO60 mW

Recommended Operating Conditions

Parameter Symbol Min. Max. Units

Operating Temperature TA-40 100 °C

Input Current, Low Level[3] IFL 0 250 µA

Input Current, High Level[4] IFH 715mA

Supply Voltage VDD1, VDD2 3.0 5.5 V

Fan Out (at TA= 1kΩ) N 5 TTL Loads

Output Pull-up Resistor RL330 4k Ω

Notes:

1. Peaking circuits may produce transient input

currents up to 50 mA, 50 ns max. pulse width,

provided average current does not exceed its

max. values.

2. Derate total package power dissipation, PT

linearly above +80°C free-air temperature at a

rate of 5.45 mW/°C for the SO8 package.

PT=number of channels multiply by (PI+PO).

For SO16 package data, contact factory for

assistance.

3. The off condition can be guaranteed by

ensuring that VFL ≤0.8V.

4. The initial switching threshold is 7 mA or

less. It is recommended that minimum 8 mA

be used for best performance and to permit

guardband for LED degradation.

Electrical Specifications

Over recommended operating range (3.0V ≤ VDD1 ≤ 3.6V, 3.0V ≤ VDD2 ≤ 3.6V, TA = -40°C to +100°C)

unless otherwise specified.

All typical specifications are at TA = +25°C , VDD1 = VDD2 = +3.3V.

Parameter Symbol Min. Typ. Max. Units Test Conditions

Input Threshold Current ITH 2.7 7.0 mA IOL(Sinking)=13 mA, VO= 0.6V

High Level Output Current IOH 4.7 100.0 µAI

F= 250 µA, VO= 3.3V

Low Level Output Voltage VOL 0.36 0.68 V IOL(Sinking) = 13 mA, IF= 7mA

High Level Supply Current (per channel) IDDH 3.2 5.0 mA IF=0 mA

Low Level Supply Current (per channel) IDDL 4.6 7.5 mA IF= 10 mA

Input Forward Voltage VF1.25 1.52 1.80 V IF= 10 mA, TA=25°C

Input Reverse Breakdown Voltage BVR5.0 V IR=10 µA

Input Diode Temperature Coefficient ∆VF / ∆TA-1.8 mV/°CI

F=10 mA

Input Capacitance CIN 80 pF f = 1 MHz, VF= 0V

Switching Specifications

Over recommended operating range (3.0V ≤ VDD1 ≤ 3.6V, 3.0V ≤ VDD2 ≤ 3.6V, IF = 8.0 mA, TA = -40°C to +100°C)

unless otherwise specified.

All typical specifications are at TA = +25°C , VDD1 = VDD2 = +3.3V.

Parameter Symbol Min. Typ. Max. Units Test Conditions

Maximum Data Rate 10 15 MBd RL = 350Ω, CL = 15 pF

Pulse Width tPW 100 ns RL = 350Ω, CL = 15 pF

Propagation Delay Time to Logic High Output Level[5] tPLH 52 100 ns RL = 350Ω, CL = 15 pF

Propagation Delay Time to Logic Low Output Level[6] tPHL 44 100 ns RL = 350Ω, CL = 15 pF

Pulse Width Distortion |tPHL – tPLH| |PWD| 8 35 ns RL = 350Ω, CL = 15 pF

Propagation Delay Skew[7] tPSK 40 ns RL = 350Ω, CL = 15 pF

Output Rise Time (10 – 90%) tR35 ns RL = 350Ω, CL = 15 pF

Output Fall Time (10 – 90%) tF12 ns RL = 350Ω, CL = 15 pF

Logic High Common Mode Transient Immunity [8] |CMH| 10 kV/µsV

cm = 1000V, IF = 0 mA,

VO = 2.0V, RL = 350Ω,

TA = 25°C

Logic Low Common Mode Transient Immunity [8] |CML| 10 kV/µsV

cm = 1000V, IF = 8 mA,

VO = 0.8V, RL = 350Ω,

TA = 25°C

Notes:

5. tPLH is measured from the 4.0 mA level on the

falling edge of the input pulse to the 1.5V

level on the rising edge of the output pulse.

6. tPHL is measured from the 4.0 mA level on the

rising edge of the input pulse to the 1.5V level

on the falling edge of the output pulse.

7. tPSK is equal to the worst case difference in

tPHL and/or tPLH that will be seen between

units at any given temperature and specified

test conditions.

8. CMH is the maximum common mode voltage

slew rate that can be sustained while

maintaining VO > 2.0V. CML is the maximum

common mode voltage slew rate that can be

sustained while maintaining VO < 0.8V. The

common mode voltage slew rates apply to

both rising and falling common mode voltage

edges.

Electrical Specifications

Over recommended operating range (4.5V ≤ VDD1 ≤ 5.5V, 4.5V ≤ VDD2 ≤ 5.5V, TA = -40°C to +100°C)

unless otherwise specified.

All typical specifications are at TA = +25°C, VDD1 = VDD2 = +5.0V.

Parameter Symbol Min. Typ. Max. Units Test Conditions

Input Threshold Current ITH 2.7 7.0 mA IOL(Sinking)=13 mA, VO= 0.6V

High Level Output Current IOH 3.8 100.0 µAI

F = 250 µA, VO= 5.5V

Low Level Output Voltage VOL 0.36 0.6 V IOL(Sinking)=13 mA, IF=7 mA

High Level Supply Current (per channel) IDDH 4.3 7.5 mA IF = 0 mA

Low Level Supply Current (per channel) IDDL 5.8 10.5 mA IF = 10 mA

Input Forward Voltage VF1.25 1.52 1.8 V IF = 10 mA, TA = 25°C

Input Reverse Breakdown Voltage BVR5.0 V IR = 10 µA

Input Diode Temperature Coefficient ∆VF / ∆TA-1.8 mV/°CI

F = 10 mA

Input Capacitance CIN 80 pF f = 1 MHz, VF = 0V

Switching Specifications

Over recommended operating range (4.5V ≤ VDD1 ≤ 5.5V, 4.5V ≤ VDD2 ≤ 5.5V, IF = 8.0 mA, TA = -40°C to +100°C)

unless otherwise specified.

All typical specifications are at TA=+25°C, VDD1 = VDD2 = +5.0V.

Parameter Symbol Min. Typ. Max. Units Test Conditions

Maximum Data Rate 10 15 MBd RL = 350Ω, CL =15 pF

Pulse Width tPW 100 ns RL = 350Ω, CL =15 pF

Propagation Delay Time to Logic High Output Level[5] tPLH 46 100 ns RL = 350Ω, CL =15 pF

Propagation Delay Time to Logic Low Output Level[6] tPHL 43 100 ns RL = 350Ω, CL =15 pF

Pulse Width Distortion |tPHL – tPLH| |PWD| 5 35 ns RL = 350Ω, CL =15 pF

Propagation Delay Skew[7] tPSK 40 ns RL = 350Ω, CL =15 pF

Output Rise Time (10 – 90%) tR30 ns RL = 350Ω, CL =15 pF

Output Fall Time (10 – 90%) tF12 ns RL = 350Ω, CL =15 pF

Logic High Common Mode Transient Immunity [8] |CMH| 10 kV/µsV

cm= 1000V, IF=0 mA,

VO = 2.0V, RL=350Ω,

TA = 25°C

Logic Low Common Mode Transient Immunity [8] |CML| 10 kV/µsV

cm= 1000V, IF= 8 mA,

VO = 0.8V, RL= 350Ω,

TA = 25°C

Notes:

5. tPLH is measured from the 4.0 mA level on the

falling edge of the input pulse to the 1.5V

level on the rising edge of the output pulse.

6. tPHL is measured from the 4.0 mA level on the

rising edge of the input pulse to the 1.5V level

on the falling edge of the output pulse.

7. tPSK is equal to the worst case difference in

tPHL and/or tPLH that will be seen between

units at any given temperature and specified

test conditions.

8. CMH is the maximum common mode voltage

slew rate that can be sustained while

maintaining VO > 2.0V. CML is the maximum

common mode voltage slew rate that can be

sustained while maintaining VO < 0.8V. The

common mode voltage slew rates apply to

both rising and falling common mode voltage

edges.

Package Characteristics

All specifications are at TA=+25°C.

Parameter Symbol Min. Typ. Max. Units Test Conditions

Input-Output Momentary SO8 VISO 2500 VRMS RH ≤50%, t = 1 min

Withstand Voltage[9] SO16 VISO 2500 RH ≤50%, t = 1 min

Input-Output Insulation[10] [11] SO8 II-O 5µA 45% RH, t=5 sec, VI-O= 3kV DC

SO16 II-O 5 45% RH, t=5 sec, VI-O=3kV DC

Input-Output Resistance[10] SO8 RI-O 1091011 ΩVI-O = 500V DC

SO16 RI-O 1091011 VI-O = 500V DC

Input-Output Capacitance[10] SO8 CI-O 0.7 pF f = 1 MHz

SO16 CI-O 0.7 f = 1 MHz

Input-Input Insulation SO8 II-I 0.005 µARH≤45%, t = 5 sec, VI-I = 500V

Leakage Current[12] SO16 II-I 0.005 RH ≤45%, t = 5 sec, VI-I = 500V

Input-Input Resistance[12] SO8 RI-I 1011 ΩRH ≤45%, t= 5 sec, VI-I = 500V

SO16 RI-I 1011 RH ≤45%, t =5 sec, VI-I =500V

Input-Input Capacitance[12] SO8 CI-I 0.1 pF f = 1 MHz

SO16 CI-I 0.12 f = 1 MHz

Electrostatic Discharge Sensitivity

This product has been tested for

electrostatic sensitivity to the

limits stated in the specifications.

However, Agilent recommends

that all integrated circuits be

handled with appropriate care to

avoid damage. Damage caused by

inappropriate handling or storage

could range from performance

degradation to complete failure.

www.agilent.com/semiconductors

For product information and a complete list of

distributors, please go to our web site.

For technical assistance call:

Americas/Canada: +1 (800) 235-0312 or

(916) 788-6763

Europe: +49 (0) 6441 92460

China: 10800 650 0017

Hong Kong: (65) 6756 2394

India, Australia, New Zealand: (65) 6755 1939

Japan: (+81 3) 3335-8152(Domestic/International), or

0120-61-1280(Domestic Only)

Korea: (65) 6755 1989

Singapore, Malaysia, Vietnam, Thailand, Philippines,

Indonesia: (65) 6755 2044

Taiwan: (65) 6755 1843

Data subject to change.

November 1, 2004

5989-1343EN

Notes:

9. VISO is a dielectric voltage rating that should

not be interpreted as an input-output

continuous voltage rating. For continuous

voltage rating, refer to the IEC/EN/DIN EN

60747-5-2 Insulation Characteristics Table (if

applicable), the equipment level safety

specification or Agilent Application Note

1074 entitled “Optocoupler Input-Output

Endurance Voltage.”

10. Measured between each input pair shorted

together and all output connections for that

channel shorted together.

11. In accordance to UL1577, each optocoupler

is proof tested by applying an insulation test

voltage ≥ 3000 Vrms for 1 sec (leakage

detection current limit, II-O ≤ 5 µA). This test

is performed before the 100% production test

for partial discharge (Method b) shown in the

IEC/EN/DIN EN 60747-5-2 Insulation

Characteristics Table, if applicable.

12. Measured between inputs with the LED

anode and cathode shorted together.