d DATA SHEET 1310NM FABRY-PEROT (FP) LASER DIODE LC OR SC PACKAGE FP-1310-4I-XXX Wide operating The FP-1310-4I-xxx is an MOCVD grown InAlGaAs ridge laser diode with emission wave-length of 1310 nm and standard continuous light output of 5mW per facet. These lasers provide stable, single transverse mode oscillation. Stable threshold current These are hermetically sealed devices in a coaxial package (TO-56) with an integrated photodiode to monitor the optical output. Suitable as a light source in data-com and telecom applications with data rates up to 4 Gb/s. 1310 nm typical emission Available in three output power options and a choice of LC and SC metal TOSA package. FEATURES: temperature (-40C to 85C) for easy transmitter control (T0 ~ 80K) wavelength FP-LDs Metal LC and SC package options High-speed modulation capability (Up to 4Gb/s) Excellent reliability * Ultra-low gradual wear-out rates * <1% failures in 20 yrs at 55C FP-1310-4I-LCA FP-1310-4I-LCB FP-1310-4I-LCC Part Number FP-1310-4I-SCC Description FP-1310-4I-LCA 1310 nm Fabry-Perot (FP) Laser Diode, LC TOSA package, high power FP-1310-4I-LCB 1310 nm Fabry-Perot (FP) Laser Diode, LC TOSA package, intermediate power FP-1310-4I-LCC 1310 nm Fabry-Perot (FP) Laser Diode, LC TOSA package, low power. FP-1310-4I-SCC 1310 nm Fabry-Perot (FP) Laser Diode, SC TOSA package, low power. FP-1310-4I-XXX 1310NM FP TOSA ABSOLUTE MAXIMUM RATINGS Parameter Output Power, CW Rating FP-1310-4I-LCA 10mW FP-1310-4I-LCB 5mW FP1310-4I-LCC 2mW FP-1310-4I-SCC Reverse Voltage (laser diode) 2V Reverse voltage (monitor photodiode) 10V Forward current (photodiode) 1mA Operating temperature -40C to +85C Storage temperature -40C to +100C ESD Exposure (Human Body Model) 200V Notice Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability. Notice The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product. FP-1310-4I-XXX 1310NM FP TOSA FP ELECTRO-OPTICAL T CASE =25C unless otherwise stated CHARACTERISTICS Parameter Optical Output Power Slope Efficiency Test Condition Symbo l Min. Typ. Max. 2 4 6 -4.0 -1.0 -0.5 Units FP-1310-4I-LCA IF = IOP FP-1310-4I-LCB IF = IOP FP-1310-4I-LCC FP-1310-4I-SCC FP-1310-4I-LCA IF = IOP -6.5 -4.3 -3 Tc = 25oC 0.07 0.1 0.19 FP-1310-4I-LCB Tc = 25oC 0.02 0.03 0.04 0.009 0.016 0.024 32 9 21 80 13 30 mA mA mA K 1.15 7 1.4 12 V 0.8 1310 1.5 1330 2.75 nm nm 0.45 0.55 nm/C tr 140 ps tf 140 ps FP-1310-4I-LCC FP-1310-4I-SCC Operating Current Threshold Current Temperature dependence of threshold current Operating Voltage Differential series resistance (laser diode) Slope efficiency ratio Lasing wavelength Spectral width under modulation Temperature dependence of lasing wavelength Rise time Fall time Relaxation oscillation frequency Monitor photodiode capacitance Tracking error Monitor photodiode dark current FP-1310-4I-LCA Monitor FP-1310-4I-LCB photodiode FP-1310-4I-LCC current FP-1310-4I-SCC PO SE o Tc = 25 C o Tc = 25 C CW, Tc = 25oC CW, Tc = 85oC CW voltage at IF = IOP CW dV/dI at T=25C PRBS 2^7-1, ER =10 dB; Ib = 1.8*Ith; RMS (sigma) 20% - 80% ; Tc = 85C; ER = 10 dB; Ib = 1.8*Ith 20% - 80% ; Tc = 85C; ER = 10 dB; Ib = 1.8*Ith Tc = 85C; I = Ith+36mA VR = 3V IF = Iop IF = Iop IF = IOP IOP ITH 3 ITH,85 T0 VOP ROP 4 SER c 0.6 1290 c/T 0.40 fR Cd TRACK Im0 Im 5.5 5 -1.5 0 30 30 130 130 +1.5 0.1 800 800 30 200 400 Notes 1 dBm 2 W/A 3 4 GHz pF dB A 5 6 A NOTES: 1. Output power is measured into a 9/125um single mode fiber 2. Slope Efficiency is measured between ITH+10mA and ITH+20mA 3. Series resistance is measured between 15mA and 25mA 4. .Slope Efficiency Ratio is defined as the ratio of SE85C/SE25C 5. Spectral width is measured according to FOTP-127 6. Tracking error is defined as the change in fiber coupled optical power when the monitor current is held constant over the operating temperature range FP-1310-4I-XXX 1310NM FP TOSA TYPICAL CHARACTERISTICS 85C, 60mA, SS=41 Typical IV curve at Tc = 25C, 45C, 65C and 85C RELATIVE OPTICAL POWER Typical LI curve at Tc = 25C, 45C, 65C and 85C 85C, 60mA, SS=41 LD chip level bandwidth at 85C 2.5Gb/s eye diagram at RT FP-1310-4I-XXX 1310NM FP TOSA TYPICAL CHARACTERISTICS PIN OUT Pin 1 2 3 4 Function Case (isolated) LD Cathode PD Anode LD Cathode / PD Anode MOUNTING DIMENSIONS For reference only. All dimensions in mm. FP-1310-4I- LCA, FP-1310-4I-LCB FP-1310-4I-XXX 1310NM FP TOSA MOUNTING DIMENSIONS For reference only. All dimensions in mm. FP-1310-4I- LCC FP-1310-4I- SCC FP-1310-4I-XXX 1310NM FP TOSA ADVANCED OPTICAL COMPONENTS AOC CAPABILITIES Finisar's ADVANCED OPTICAL COMPONENTS division was formed through strategic acquisition of key optical component suppliers. The company has led the industry in high volume Vertical Cavity Surface Emitting Laser (VCSEL) and associated detector technology since 1996. VCSELs have become the primary laser source for optical data communication, and are rapidly expanding into a wide variety of sensor applications. VCSELs' superior reliability, low drive current, high coupled power, narrow and circularly symmetric beam and versatile packaging options (including arrays) are enabling solutions not possible with other optical technologies. ADVANCED OPTICAL COMPONENTS is also a key supplier of Fabrey-Perot (FP) and Distributed Feedback (DFB) Lasers, and Optical Isolators (OI) for use in single mode fiber data and telecommunications networks ADVANCED OPTICAL COMPONENTS' advanced capabilities include: LOCATION Allen, TX - Business unit headquarters, VCSEL wafer growth, wafer fabrication and TO package assembly. Fremont, CA - Wafer growth and fabrication of 1310 to 1550nm FP and DFB lasers. Shanghai, PRC - Optical passives assembly, including optical isolators and splitters. 1, 2, 4, 8, and 10Gbps serial VCSEL solutions 1, 2, 4, 8, and 10Gbps serial SW DETECTOR solutions VCSEL and detector arrays 1, 2, 4, 8, and 10Gbps FP and DFB solutions at 1310 and 1550nm 1, 2, 4, 8, and 10Gbps serial LW DETECTOR solutions Optical Isolators from 1260 to 1600nm range Laser packaging in TO46, TO56, and Optical subassemblies with SC, LC, and MU interfaces for communication networks VCSELs operating at 670nm, 780nm, 980nm, and 1310nm in development Sensor packages include surface mount, various plastics, chip on board, chipscale packages, etc. Custom packaging options SALES AND SERVICE Finisar's ADVANCED OPTICAL COMPONENTS division serves its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact a nearby sales office or call the number listed below. Phone: 1-866-MY-VCSEL USA (toll free) 1-214-509-2700 USA (Direct dial) 44 (0) 174 336 5533 Europe 886-935-409898 China & Taiwan 81-90-4437-1130 Japan 82-11-220-6153 Asia Pacific & Korea Fax: 1-2140509-3709 USA Email: support@adopco.com WEB: www.finisar.com/aoc.php (c)2008 Finisar Corporation. All rights reserved. Finisar is a registered trademark of Finisar Corporation. Features and specifications are subject to change without notice. 2/10