FP-1310-4I-LCC - FINISAR - Datasheet.Live

DATA

SHEET

1310NM FABR

-PEROT (FP)

LASER DIODE

LC OR SC PACKAGE

FP-1310-4I-XXX

FEATURES:



Wide operating

temperature (-40°C to

85°C)



Stable threshold current

for easy transmitter control

(T0 ~ 80K)



1310 nm typical emission

wavelength FP-LDs



Metal LC and SC package

options



High-speed modulation

capability (Up to 4Gb/s)



Excellent reliability

• Ultra-low gradual

wear-out rates

• <1% failures in 20 yrs at

55°C

The FP-1310-4I-xxx is an MOCVD grown InAlGaAs ridge laser diode with emission

wave-length of 1310 nm and standard continuous light output of 5mW per facet. These

lasers provide stable, single transverse mode oscillation.

These are hermetically sealed devices in a coaxial package (TO-56) with an integrated

photodiode to monitor the optical output. Suitable as a light source in data-com and

telecom applications with data rates up to 4 Gb/s.

Available in three output power options and a choice of LC and SC metal TOSA

package.

Part Number Description

FP-1310-4I-LCA 1310 nm Fabry-Perot (FP) Laser Diode, LC TOSA package, high power

FP-1310-4I-LCB 1310 nm Fabry-Perot (FP) Laser Diode, LC TOSA package, intermediate power

FP-1310-4I-LCC 1310 nm Fabry-Perot (FP) Laser Diode, LC TOSA package, low power.

FP-1310-4I-SCC 1310 nm Fabry-Perot (FP) Laser Diode, SC TOSA package, low power.

FP-1310-4I-LCA FP-1310-4I-SCC

FP-1310-4I-LCB

FP-1310-4I-LCC

FP-1310-4I-XXX 1310NM FP TOSA

ABSOLUTE MAXIMUM RATINGS

Parameter Rating

FP-1310-4I-LCA 10mW

FP-1310-4I-LCB 5mW

Output Power, CW FP1310-4I-LCC

FP-1310-4I-SCC

2mW

Reverse Voltage (laser diode) 2V

Reverse voltage (monitor photodiode) 10V

Forward current (photodiode) 1mA

Operating temperature -40°C to +85°C

Storage temperature -40°C to +100°C

ESD Exposure (Human Body Model) 200V

Notice

Stresses greater than those listed under “Absolute Maximum Ratings”

may cause permanent damage to the device. This is a stress rating

only and functional operation of the device at these or any other

conditions above those indicated in the operations section for

extended periods of time may affect reliability.

Notice

The inherent design of this component causes it to be sensitive to

electrostatic discharge (ESD). To prevent ESD-induced damage

and/or degradation to equipment, take normal ESD precautions when

handling this product.

FP-1310-4I-XXX 1310NM FP TOSA

Parameter Test Condition Symbo

l Min. Typ. Max. Units Notes

FP-1310-4I-LCA IF = IOP 2 4 6

FP-1310-4I-LCB IF = IOP -4.0 -1.0 -0.5

Optical

Output

Power FP-1310-4I-LCC

FP-1310-4I-SCC

IF = IOP

-6.5 -4.3 -3

dBm

FP-1310-4I-LCA Tc = 25oC 0.07 0.1 0.19

FP-1310-4I-LCB Tc = 25oC 0.02 0.03 0.04

Slope

Efficiency FP-1310-4I-LCC

FP-1310-4I-SCC

Tc = 25oC

0.009 0.016 0.024

W/A

Operating Current Tc = 25oC IOP 32 mA

CW, Tc = 25oC ITH 3 9 13 mA Threshold Current

CW, Tc = 85oC ITH,85 21 30 mA

Temperature dependence of

threshold current

0 80 K

Operating Voltage CW voltage at IF = IOP V

OP 1.15 1.4 V

Differential series resistance

(laser diode)

CW dV/dI at T=25°C

ROP 4 7 12 Ω 3

Slope efficiency ratio SER 0.6 0.8 - 4

Lasing wavelength λc 1290 1310 1330 nm

Spectral width under modulation PRBS 2^7-1, ER =10

dB;

Ib = 1.8*Ith; RMS

(sigma)

Δλ 1.5 2.75 nm 5

Temperature dependence of

lasing wavelength

Δλc/ΔT 0.40 0.45 0.55 nm/C

Rise time 20% - 80% ; Tc = 85°C;

ER = 10 dB; Ib = 1.8*Ith

tr 140 ps

Fall time 20% - 80% ; Tc = 85°C;

ER = 10 dB; Ib = 1.8*Ith

tf 140 ps

Relaxation oscillation frequency Tc = 85°C; I = Ith+36mA fR 5.5 GHz

Monitor photodiode capacitance Cd 5 pF

Tracking error ΔTRACK -1.5 +1.5 dB 6

Monitor photodiode dark current VR = 3V Im0 0 0.1 µA

FP-1310-4I-LCA IF = Iop 30 130 800

FP-1310-4I-LCB IF = Iop 30 130 800

Monitor

photodiode

current FP-1310-4I-LCC

FP-1310-4I-SCC

IF = IOP Im

30 200 400

µA

FP ELECTRO-OPTICAL

CHARAC

TERISTICS

E =25°C unless otherwise stated

NOTES:

1. Output power is measured into a 9/125um single mode fiber

2. Slope Efficiency is measured between ITH+10mA and ITH+20mA

3. Series resistance is measured between 15mA and 25mA

4. .Slope Efficiency Ratio is defined as the ratio of SE85C/SE25C

5. Spectral width is measured according to FOTP-127

6. Tracking error is defined as the change in fiber coupled optical power when the monitor current is held constant over

the operating temperature range

FP-1310-4I-XXX 1310NM FP TOSA

TYPICAL CHARACTERISTICS

85°C, 60mA, SS=41 85°C, 60mA, SS=41

Typical LI curve at Tc = 25°C, 45°C, 65°C and 85°CTypical IV curve at Tc = 25°C, 45°C, 65°C and 85°C

LD chip level bandwidth at 85°C 2.5Gb/s eye diagram at RT

RELATIVE OPTICAL POWER

FP-1310-4I-XXX 1310NM FP TOSA

PIN OUT

TYPICAL CHARACTERISTICS

Pin Function

1 Case (isolated)

2 LD Cathode

3 PD Anode

4 LD Cathode / PD

Anode

MOUNTING DIMENSIONS

For reference only. All dimensions in mm.

FP-1310-4I- LCA, FP-1310-4I-LCB

FP-1310-4I-XXX 1310NM FP TOSA

MOUNTING DIMENSIONS

For reference only. All dimensions in mm.

FP-1310-4I- LCC

FP-1310-4I- SCC

FP-1310-4I-XXX 1310NM FP TOSA

ADVANCED OPTICAL COMPONENTS

Finisar’s ADVANCED OPTICAL COMPONENTS division

was formed through strategic acquisition of key optical

component suppliers. The company has led the industry

in high volume Vertical Cavity Surface Emitting Laser

(VCSEL) and associated detector technology since 1996.

VCSELs have become the primary laser source for

optical data communication, and are rapidly expanding

into a wide variety of sensor applications. VCSELs’

superior reliability, low drive current, high coupled power,

narrow and circularly symmetric beam and versatile

packaging options (including arrays) are enabling

solutions not possible with other optical technologies.

ADVANCED OPTICAL COMPONENTS is also a key

supplier of Fabrey-Perot (FP) and Distributed Feedback

(DFB) Lasers, and Optical Isolators (OI) for use in single

mode fiber data and telecommunications networks

LOCATION



Allen, TX - Business unit headquarters, VCSEL

wafer growth, wafer fabrication and TO package

assembly.



Fremont, CA – Wafer growth and fabrication of

1310 to 1550nm FP and DFB lasers.



Shanghai, PRC – Optical passives assembly,

including optical isolators and splitters.

SALES AND SERVICE

Finisar’s ADVANCED OPTICAL COMPONENTS division

serves its customers through a worldwide network of

sales offices and distributors. For application assistance,

current specifications, pricing or name of the nearest

Authorized Distributor, contact a nearby sales office or

call the number listed below.

AOC CAPABILITIES

ADVANCED OPTICAL COMPONENTS’ advanced

capabilities include:



1, 2, 4, 8, and 10Gbps serial VCSEL solutions



1, 2, 4, 8, and 10Gbps serial SW DETECTOR

solutions

VCSEL and detector arrays



1, 2, 4, 8, and 10Gbps FP and DFB solutions at

1310 and 1550nm



1, 2, 4, 8, and 10Gbps serial LW DETECTOR

solutions



Optical Isolators from 1260 to 1600nm range



Laser packaging in TO46, TO56, and Optical

subassemblies with SC, LC, and MU interfaces

for communication networks



VCSELs operating at 670nm, 780nm, 980nm,

and 1310nm in development



Sensor packages include surface mount, various

plastics, chip on board, chipscale packages, etc.

Custom packaging options

Phone: 1-866-MY-VCSEL USA (toll free)

1-214-509-2700 USA (Direct dial)

44 (0) 174 336 5533 Europe

886-935-409898 China & Taiwan

81-90-4437-1130 Japan

82-11-220-6153 Asia Pacific &

Korea

Fax: 1-2140509-3709 USA

Email: support@adopco.com

WEB: www.finisar.com/aoc.php