Multilayer Ceramic Capacitors Capacitor Arrays Series Description: WTC middle and high voltage series MLCC is designed by a special internal electrode pattern, which can reduce voltage concentrations by distributing voltage gradients throughout the entire capacitor. This special design also affords increased capacitance values in a given case size and voltage rating. WTC capacitor arrays are developed to offer designers the opportunity to lower placement costs increase assembly line output through lower component count per board. Features: * * * High density mounting due to mounting space saving. Mounting cost saving. Increased throughput. Applications: * * * or use as a bypass for digital and analog signal line noise F Computer motherboards and peripherals. The other common electronic circuits. External Dimensions: Size Inch (mm) L (mm) W (mm) T (mm)/Symbol 0508 (1220) 2 0.15 1.25 0.15 0.85 0.1 T 0.2 0.1 0.25 0.1 0.5 0.1 0612 (1632) 3.2 0.15 1.6 0.15 0.8 0.1 B 0.3 0.2 0.4 0.15 0.8 0.15 S (mm) BW (mm) P (mm) Reflow soldering process only. www.element14.com www.farnell.com www.newark.com Page <1> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series General Electrical Data: Dielectric NP0 Size Capacitance* X7R 4x0402 4x0603 4x0402 4x0603 10pF to 270pF 10pF to 470pF 1,000pF to 100nF 180pF to 100nF Capacitance tolerance** J (5%), K (10%) K (10%), M (20%) Rated voltage (WVDC) 50V 25, 50V Q/Tan * Cap<30pF: Q400+20C Cap30pF: Q1000 Insulation resistance at Ur 10V, 16V, 25V, 50V 16V, 25V, 50V Ur=50V, 2.5% Ur=25V&16V, 3.5% Ur=10V, 5.0% 10G 10Gor RxC500xF whichever is less Operating temperature -55C to +125C Capacitance characteristic 30ppm Termination Ni/Sn (lead-free termination) * Measured at 30~70% related humidity. NP0: Apply 1.00.2Vrms, 1.0MHz10% at the conditions of 25C ambient temperature. X7R: Apply 1.00.2Vrms, 1.0kHz10%, at the conditions of 25C ambient temperature. ** Preconditioning for Class II MLCC: Perform a heat treatment at 15010C for 1 hour, then leave in ambient condition for 242 hours before measurement. Packaging Dimension And Quantity: Paper Tape Thickness/Symbol (mm) Size 7" reel 13" reel 4 x 0402 0.85 0.1 T 4k - 4 x 0603 0.8 0.1 B 4k Unit: pieces Capacitance Range: Size 4 x 0402 NP0 Rated Voltage (VDC) 50 Capacitance Dielectric 4 x 0603 X7R 10 16 NP0 25 50 X7R 25 50 10pF (100) T B B 15pF (150) T B B 22pF (220) T B B 33pF (330) T B B 47pF (470) T B B 68pF (680) T B B 100pF (101) T B B 150pF (151) T B B 180pF (181) T B B 16 25 50 B B www.element14.com www.farnell.com www.newark.com Page <2> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series Capacitance Range: Size 4 x 0402 Dielectric NP0 Rated Voltage (VDC) 50 4 x 0603 X7R 10 16 NP0 25 50 X7R 25 50 16 50 220pF (221) T B B B B 270pF (271) T B B B B 330pF (331) B B B B 470pF (471) B B B B 6,80pF (681) Capacitance 25 B B 1,000pF (102) T T T T B B 1,500pF (152) T T T T B B 2,200pF (222) T T T T B B 3,300pF (332) T T T T B B 4,700pF (472) T T T T B B 6,800pF (682) T T T T B B 0.010F (103) T T T T B B 0.015F (153) T T T B B B 0.022F (223) T T T B B B 0.033F (333) T T T B 0.047F (473) T T T B 0.068F (683) T T T B 0.10F (104) T T T B 1. The letter in cell is expressed the symbol of product thickness. Reliability Test Conditions and Requirements: No Item Test Condition Requirements 1 Visual and Mechanical - 2 Capacitance 3 Q/ D.F. (Dissipation Factor) 4 Dielectric Strength * To apply voltage (100V) 250%. * Duration: 1 to 5 sec. * Charge and discharge current less than 50mA. * No evidence of damage or flash over during test. 5 Insulation Resistance To apply rated voltage for max. 120 sec. 10G or RxC500-F whichever is smaller. * No remarkable defect. * Dimensions to conform to individual specification sheet. * Shall not exceed the limits given in the detailed spec. Class I: NP0 1 0.2Vrms, 1MHz 10% Class II: (X7R) 1 0.2Vrms, 1kHz 10% NP0: Cap30pF, Q1000; Cap<30pF, Q400+20C X7R: Ur=50V, 2.5%; Ur=25V&16V, 3.5%; Ur=10V, 5.0% www.element14.com www.farnell.com www.newark.com Page <3> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series Reliability Test Conditions and Requirements: No Item Test Condition Requirements With no electrical load. 6 Temperature Coefficient T.C. Operating Temperature NP0) 55~125C at 25C X7R -55~125C at 25C T.C. Capacitance Change NP0 Within 30ppm/C X7R Within 15% 7 Adhesive Strength of Termination Pressurizing force: 5N (0603) and 10N (>0603) Test time: 10 1 sec. No remarkable damage or removal of the terminations. 8 Vibration Resistance Vibration frequency: 10~55 Hz/min. Total amplitude: 1.5mm Test time: 6 hrs. (Two hrs each in three mutually perpendicular directions.) No remarkable damage. Cap change and Q/D.F.: To meet initial spec. 9 Solderability Solder temperature: 235 5C Dipping time: 2 0.5 sec. 95% min. coverage of all metalized area. Bending Test The middle part of substrate shall be pressurized by means of the pressurizing rod at a rate of about 1mm per second until the deflection becomes 1mm and then the pressure shall be maintained for 5 1 sec. Measurement to be made after keeping at room temp. for 24 2 hrs. No remarkable damage. Cap change NP0: within 5.0% or 0.5pF whichever is larger. X7R: within 12.5% (This capacitance change means the change of capacitance under specified flexure of substrate from the capacitance measured before the test.) Resistance to Soldering Heat Solder temperature: 260 5C Dipping time: 10 1 sec Preheating: 120 to 150C for 1 minute before immerse the capacitor in a eutectic solder. Before initial measurement (Class II only): Perform 150+0/-10C for 1 hr and then set for 48 4hrs at room temp. Measurement to be made after keeping at room temp. for 24 2 hrs. (Class I) or 48 4 hrs. (Class II). No remarkable damage. Cap change: NP0: within 2.5% or 0.25pF whichever is larger. X7R: within 7.5% Q/D.F., I.R. and dielectric strength: To meet initial requirements. 25% max. leaching on each edge. 10 11 Conduct the five cycles according to the temperatures and time. 12 Temperature Cycle Step Temp. (C) Time (Min.) 1 Min. operating temp. +0/-3 303 2 Room temp. 2~3 3 Max. operating temp. +3/-0 303 4 Room temp. 2~3 Before initial measurement (Class II only): Perform 150+0/-10C for 1hour and then set for 242 hrs at room temp. Measurement to be made after keeping at room temp. for 242 hrs. (Class I) or 484 hrs. (Class II). No remarkable damage. Cap change: NP0: within 2.5% or 0.25pF whichever is larger. X7R: within 7.5% Q/D.F., I.R. and dielectric strength: To meet initial requirements. www.element14.com www.farnell.com www.newark.com Page <4> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series Reliability Test Conditions and Requirements: No 13 14 15 Item Humidity (Damp Heat) Steady State Humidity (Damp Heat) Load High Temperature Load (Endurance) Test Condition Requirements Test temp.: 402C Humidity: 90~95% RH Test time: 500+24/-0hrs. Measurement to be made after keeping at room temp. for 242 hrs. (Class I) or 484 hrs. (Class II). No remarkable damage. Cap change: NP0: within 5.0% or 0.5pF whichever is larger. X7R: within 12.5% Q/D.F. value: NP0: C ap30pF, Q350; 10pFCap<30pF, Q275+2.5C Cap<10pF; Q200+10C X7R: Ur=50V, 3%; Ur=25V&16V, 5%; Ur=10V, 7.5% I.R.: 1G or RxC50-F whichever is smaller. Test temp.: 402C Humidity: 90~95%RH Test time: 500+24/-0 hrs. To apply voltage: rated voltage. Measurement to be made after keeping at room temp. for 242 hrs. (Class I) or 484 hrs. (Class II). No remarkable damage. Cap change: NP0: within 7.5% or 0.75pF whichever is larger. X7R: within 12.5% Q/D.F. value: NP0: Cap30pF, Q200; Cap<30pF, Q100+10/3C X7R: Ur=50V, 3%; Ur=25V&16V, 5%; Ur=10V, 7.5% I.R.: 500Mor RxC25-F whichever is smaller. Test temp.: NP0, X7R: 1253C To apply voltage: 200% of rated voltage. Test time: 1000+24/-0 hrs. Measurement to be made after keeping at room temp. for 242 hrs. (Class I) or 484 hrs. (Class II). No remarkable damage. Cap change: NP0: within 3.0% or 0.3pF whichever is larger. X7R: within 12.5% Q/D.F. value: NP0: C ap30pF, Q350 10pFCap<30pF, Q275+2.5C Cap<10pF, Q200+10C X7R: Ur=50V, 3%; Ur=25V&16V, 5%; Ur=10V, 7.5% I.R.: 1G or RxC50-F whichever is smaller. Appendixes Reel Dimensions Size 4x0402, 4x0603 Reel size 7" C 13 +0.5/-0.2 W1 8.4 +1.5/-0 A 178 0.1 N 60 +1/-0 www.element14.com www.farnell.com www.newark.com Page <5> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series Tape Dimensions Size 4x0402 4x0603 Thickness T B The dimension of paper tape Constructions: A0 1.5 0.1 2 0.1 B0 2.3 0.1 3.5 0.1 T 0.95 0.05 0.95 0.05 K0 - - W 8 0.1 8 0.1 P0 4 0.1 4 0.1 10xP0 40 0.1 40 0.1 P1 4 0.1 4 0.1 P2 2 0.05 2 0.05 D0 1.55 0.05 1.5 0.05 D1 - - E 1.75 0.05 1.75 0.1 F 3.5 0.05 3.5 0.05 No. Name NP0 & X7R, 1 Ceramic material BaTiO3 based 2 Inner electrode Ni 3 4 Termination 5 Inner layer Cu Middle layer Ni Outer layer Sn (Matt) Storage and handling conditions (1) To store products at 5 to 40C ambient temperature and 20 to 70%. related humidity conditions. (2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life extension is needed. Cautions: a. The corrosive gas reacts on the terminal electrodes of capacitors, and results in the poor solderability. Do not store the capacitors in the ambience of corrosive gas (e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas etc.) b. In corrosive atmosphere, solderability might be degraded, and silver migration might occur to cause low reliability. c. Due to the dewing by rapid humidity change, or the photochemical change of the terminal electrode by direct sunlight,the solderability and electrical performance may deteriorate. Do not store capacitors under direct sunlight or dewing condition. To store products on the shelf and avoid exposure to moisture. www.element14.com www.farnell.com www.newark.com Page <6> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series Recommended Soldering Conditions: The lead-free termination MLCCs are not only to be used on SMT against lead-free solder paste, but also suitable against lead-containing solder paste. If the optimized solder joint is requested, increasing soldering time, temperature and concentration of N2 within oven are recommended. Recommended reflow soldering profile for SMT process with SnAgCu series solder paste. Recommended wave soldering profile for SMT process with SnAgCu series solder. www.element14.com www.farnell.com www.newark.com Page <7> 12/04/13 V1.0 Multilayer Ceramic Capacitors Capacitor Arrays Series Part Number Table Description Partnumber Capacitor, RF, 0.1UF, 10V, X7R, 4x0402 MC000249 Capacitor, RF, 0.01UF, 50V, X7R, 4x0603 MC000250 Capacitor, RF, 0.01UF, 50V, X7R, 4x0603 MC000251 Capacitor, RF, 0.01UF, 50V, X7R, 4x0603 MC000252 Capacitor, RF, 100PF, 50V, NP0, 4x0603 MC000253 Capacitor, RF, 150PF, 50V, NP0, 4x0603 MC000254 Capacitor, RF, 180PF, 50V, NP0, 4x0603 MC000255 Capacitor, RF, 220PF, 50V, NP0, 4x0603 MC000256 Capacitor, RF, 33PF, 50V, NP0, 4x0603 MC000257 Capacitor, RF, 330PF, 50V, NP0, 4x0603 MC000258 Capacitor, RF, 100PF, 50V, NP0, 4x0603 MC000259 Capacitor, RF, 220PF, 50V, NP0, 4x0603 MC000260 Capacitor, RF, 47PF, 50V, NP0, 4x0603 MC000261 Capacitor, RF, 470PF, 50V, NP0, 4x0603 MC000262 Capacitor, RF, 470PF, 50V, NP0, 4x0603 MC000263 Capacitor, RF, 0.01UF, 25V, X7R, 4x0603 MC000264 Capacitor, RF, 0.047UF, 16V, X7R, 4x0603 MC000265 Capacitor, RF, 1000PF, 50V, X7R, 4x0603 MC000266 Capacitor, RF, 1000PF, 50V, X7R, 4x0603 MC000267 Capacitor, RF, 0.022UF, 50V, X7R, 4x0603 MC000268 Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2012. www.element14.com www.farnell.com www.newark.com Page <8> 12/04/13 V1.0