TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F – DECEMBER 1993 – REVISED NOVEMBER 2001
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
D
12-Bit-Resolution A/D Converter
D
10-µs Conversion Time Over Operating
Temperature
D
11 Analog Input Channels
D
3 Built-In Self-Test Modes
D
Inherent Sample-and-Hold Function
D
Linearity Error . . . ±1 LSB Max
D
On-Chip System Clock
D
End-of-Conversion Output
D
Unipolar or Bipolar Output Operation
(Signed Binary With Respect to 1/2 the
Applied Voltage Reference)
D
Programmable MSB or LSB First
D
Programmable Power Down
D
Programmable Output Data Length
D
CMOS Technology
D
Application Report Available
description
The TLC2543C and TLC2543I are 12-bit, switched-
capacitor, successive-approximation, analog-to-
digital converters. Each device, with three control
inputs [chip select (CS), the input-output clock, and
the address input (DATA INPUT)], is designed for
communication with the serial port of a host processor
or peripheral through a serial 3-state output. The
device allows high-speed data transfers from the
host.
In addition to the high-speed converter and versatile control capability, the device has an on-chip 14-channel
multiplexer that can select any one of 11 inputs or any one of three internal self-test voltages. The
sample-and-hold function is automatic. At the end of conversion, the end-of-conversion (EOC) output goes high
to indicate that conversion is complete. The converter incorporated in the device features differential
high-impedance reference inputs that facilitate ratiometric conversion, scaling, and isolation of analog circuitry
from logic and supply noise. A switched-capacitor design allows low-error conversion over the full operating
temperature range.
The TLC2543C is characterized for operation from TA = 0°C to 70°C. The TLC2543I is characterized for
operation from T A = –40°C to 85°C. The TLC2543M is characterized for operation from T A = 55°C to 125°C.
Copyright 2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Microcontroller Based Data Acquisition Using the TLC2543 12-bit Serial-Out ADC (SLAA012)
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
GND
VCC
EOC
I/O CLOCK
DATA INPUT
DATA OUT
CS
REF+
REF
AIN10
AIN9
(TOP VIEW)
DB, DW, J, OR N PACKAGE
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
I/O CLOCK
DATA INPUT
DATA OUT
CS
AIN3
AIN4
AIN5
AIN6
AIN7
FN PACKAGE
(TOP VIEW)
AIN1
AIN0
AIN10
REF –
AIN2
EOC
AIN8
GND
AIN9 VCC
REF+
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
2POST OFFICE BOX 655303 DALLAS, TEXAS 75265
AVAILABLE OPTIONS
PACKAGE
TASMALL OUTLINE PLASTIC CHIP
CARRIER CERAMIC DIP PLASTIC DIP
(DB)(DW)(FN)(J) (N)
0°C to 70°C TLC2543CDB TLC2543CDW TLC2543CFN TLC2543CN
40°C to 85°C TLC2543IDB TLC2543IDW TLC2543IFN TLC2543IN
55°C to 125°C TLC2543MJ
Available in tape and reel and ordered as the TLC2543CDBLE, TLC2543IDBR, TLC2543CDWR, TLC2543IDWR, TLC2543CFNR, or
TLC2543IFNR.
functional block diagram
14-Channel
Analog
Multiplexer
Sample-and-
Hold
Function
12-Bit
Analog-to-Digital
Converter
(Switched Capacitors)
Self-Test
Reference
Output
Data
Register
12-to-1 Data
Selector and
Driver
Control Logic
and I/O
Counters
Input Address
Register
4
12
12
4
REF+ REF
DATA
OUT
DATA
INPUT
I/O CLOCK
CS
3
EOC
17
18
15
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
1
2
3
4
5
6
7
8
9
11
12
14 13
16
19
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
3
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME NO.
I/O
DESCRIPTION
AIN0 AIN10 19,
11, 12 IAnalog input. These 1 1 analog-signal inputs are internally multiplexed. The driving source impedance should
be less than or equal to 50 for 4.1-MHz I/O CLOCK operation and be capable of slewing the analog input
voltage into a capacitance of 60 pF.
CS 15 I Chip select. A high-to-low transition on CS resets the internal counters and controls and enables DA T A OUT,
DA T A INPUT, and I/O CLOCK. A low-to-high transition disables DA T A INPUT and I/O CLOCK within a setup
time.
DATA INPUT 17 I Serial-data input. A 4-bit serial address selects the desired analog input or test voltage to be converted next.
The serial data is presented with the MSB first and is shifted in on the first four rising edges of I/O CLOCK.
After the four address bits are read into the address register, I/O CLOCK clocks the remaining bits in order .
DATA OUT 16 O The 3-state serial output for the A/D conversion result. DATA OUT is in the high-impedance state when CS
is high and active when CS is low. With a valid CS, DATA OUT is removed from the high-impedance state
and is driven to the logic level corresponding to the MSB/LSB value of the previous conversion result. The
next falling edge of I/O CLOCK drives DA T A OUT to the logic level corresponding to the next MSB/LSB, and
the remaining bits are shifted out in order.
EOC 19 O End of conversion. EOC goes from a high to a low logic level after the falling edge of the last I/O CLOCK and
remains low until the conversion is complete and the data is ready for transfer.
GND 10 Ground. GND is the ground return terminal for the internal circuitry. Unless otherwise noted, all voltage
measurements are with respect to GND.
I/O CLOCK 18 I Input/output clock. I/O CLOCK receives the serial input and performs the following four functions:
1. It clocks the eight input data bits into the input data register on the first eight rising edges of I/O CLOCK
with the multiplexer address available after the fourth rising edge.
2. On the fourth falling edge of I/O CLOCK, the analog input voltage on the selected multiplexer input
begins charging the capacitor array and continues to do so until the last falling edge of the I/O
CLOCK.
3. It shifts the 11 remaining bits of the previous conversion data out on DATA OUT. Data changes on
the falling edge of I/O CLOCK.
4. It transfers control of the conversion to the internal state controller on the falling edge of the last
I/O CLOCK.
REF+ 14 I Positive reference voltage The upper reference voltage value (nominally VCC) is applied to REF+. The
maximum input voltage range is determined by the difference between the voltage applied to this terminal and
the voltage applied to the REF terminal.
REF13 I Negative reference voltage. The lower reference voltage value (nominally ground) is applied to REF.
VCC 20 Positive supply voltage
MSB/LSB = Most significant bit / least significant bit
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
4POST OFFICE BOX 655303 DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise
noted)
Supply voltage range, VCC (see Note 1) 0.5 V to 6.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (any input) 0.3 V to VCC + 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage range, VO 0.3 V to VCC + 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positive reference voltage, Vref+ V
CC + 0.1 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Negative reference voltage, Vref 0.1 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peak input current, II (any input) ±20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peak total input current, II (all inputs) ±30 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: TLC2543C 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLC2543I 40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TLC2543M 55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg 65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from the case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
NOTE 1: All voltage values are with respect to the GND terminal with REF and GND wired together (unless otherwise noted).
recommended operating conditions
MIN NOM MAX UNIT
Supply voltage, VCC 4.5 5 5.5 V
Positive reference voltage, V ref+ (see Note 2) VCC V
Negative reference voltage, V ref (see Note 2) 0 V
Differential reference voltage, Vref+ Vref (see Note 2) 2.5 VCC VCC+0.1 V
Analog input voltage (see Note 2) 0 VCC V
High-level control input voltage, VIH VCC = 4.5 V to 5.5 V 2 V
Low-level control input voltage, VIL VCC = 4.5 V to 5.5 V 0.8 V
Clock frequency at I/O CLOCK 0 4.1 MHz
Setup time, address bits at DATA INPUT before I/O CLOCK, tsu(A) (see Figure 4) 100 ns
Hold time, address bits after I/O CLOCK, th(A) (see Figure 4) 0 ns
Hold time, CS low after last I/O CLOCK, th(CS) (see Figure 5) 0 ns
Setup time, CS low before clocking in first address bit, tsu(CS) (see Note 3 and Figure 5) 1.425 µs
Pulse duration, I/O CLOCK high, twH(I/O) 120 ns
Pulse duration, I/O CLOCK low, twL(I/O) 120 ns
T ransition time, I/O CLOCK high to low, tt(I/O) (see Note 4 and Figure 6) 1µs
T ransition time, DATA INPUT and CS, tt(CS) 10 µs
TLC2543C 0 70
Operating free-air temperature, TATLC2543I 40 85 °C
TLC2543M 55 125
NOTES: 2. Analog input voltages greater than that applied to REF+ convert as all ones (111111111111), while input voltages less than that applied
to REF convert as all zeros (000000000000).
3. T o minimize errors caused by noise at the CS input, the internal circuitry waits for a setup time after CS before responding to control
input signals. No attempt should be made to clock in an address until the minimum CS setup time has elapsed.
4. This is the time required for the clock input signal to fall from VIHmin to VILmax or to rise from VILmax to VIHmin. In the vicinity of
normal room temperature, the devices function with input clock transition time as slow as 1 µs for remote data acquisition applications
where the sensor and the A/D converter are placed several feet away from the controlling microprocessor.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
5
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range,
VCC = Vref+ = 4.5 V to 5.5 V, f(I/O CLOCK) = 4.1 MHz (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TLC2543C, TLC2543I
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYPMAX
UNIT
VOH
High level out
p
ut voltage
VCC = 4.5 V, IOH = 1.6 mA 2.4
V
V
OH
High
-
level
output
voltage
VCC = 4.5 V to 5.5 V, IOH = 20 µA VCC0.1
V
VOL
Low level out
p
ut voltage
VCC = 4.5 V, IOL = 1.6 mA 0.4
V
V
OL
Low
-
level
output
voltage
VCC = 4.5 V to 5.5 V, IOL = 20 µA 0.1
V
IOZ
Hi
g
h-impedance off-state output VO = VCC, CS at VCC 1 2.5
µA
I
OZ
g
current VO = 0, CS at VCC 12.5 µ
A
IIH High-level input current VI = VCC 1 2.5 µA
IIL Low-level input current VI = 0 12.5 µA
ICC Operating supply current CS at 0 V 1 2.5 mA
ICC(PD) Power-down current For all digital inputs,
0 VI 0.5 V or VI VCC 0.5 V 4 25 µA
Selected channel leakage
Selected channel at VCC,Unselected channel at 0 V 1
Selected
channel
leakage
current Selected channel at 0 V,
Unselected channel at VCC 1µA
Maximum static analog
reference current into REF+ Vref+ = VCC, Vref = GND 1 2.5 µA
Ci
Input Analog inputs 30 60 p
F
C
icapacitance Control inputs 5 15
pF
All typical values are at VCC = 5 V, TA = 25°C.
electrical characteristics over recommended operating free-air temperature range,
VCC = Vref+ = 4.5 V to 5.5 V, f(I/O CLOCK) = 4.1 MHz (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TLC2543M
UNIT
PARAMETER
TEST
CONDITIONS
MIN TYPMAX
UNIT
VOH
High level out
p
ut voltage
VCC = 4.5 V, IOH = 1.6 mA 2.4
V
V
OH
High
-
level
output
voltage
VCC = 4.5 V to 5.5 V, IOH = 20 µA VCC0.1
V
VOL
Low level out
p
ut voltage
VCC = 4.5 V, IOL = 1.6 mA 0.4
V
V
OL
Low
-
level
output
voltage
VCC = 4.5 V to 5.5 V, IOL = 20 µA 0.1
V
IOZ
Hi
g
h-impedance off-state output VO = VCC, CS at VCC 1 2.5
µA
I
OZ
g
current VO = 0, CS at VCC 12.5 µ
A
IIH High-level input current VI = VCC 1 10 µA
IIL Low-level input current VI = 0 110 µA
ICC Operating supply current CS at 0 V 1 2.5 mA
ICC(PD) Power-down current For all digital inputs,
0 VI 0.5 V or VI VCC 0.5 V 4 25 µA
Selected channel leakage
Selected channel at VCC,Unselected channel at 0 V 10
Selected
channel
leakage
current Selected channel at 0 V,
Unselected channel at VCC 10 µA
Maximum static analog
reference current into REF+ Vref+ = VCC, Vref = GND 1 2.5 µA
Ci
Input Analog inputs 30 60 p
F
C
icapacitance Control inputs 5 15
pF
All typical values are at VCC = 5 V, TA = 25°C.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
6POST OFFICE BOX 655303 DALLAS, TEXAS 75265
operating characteristics over recommended operating free-air temperature range,
VCC = Vref+ = 4.5 V to 5.5 V, f(I/O CLOCK) = 4.1 MHz
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
ELLinearity error (see Note 5) See Figure 2 ±1 LSB
EDDifferential linearity error See Figure 2 ±1 LSB
EOOffset error (see Note 6) See Note 2 and
Figure 2 ±1.5 LSB
EGGain error (see Note 6) See Note 2 and
Figure 2 ±1 LSB
ETTotal unadjusted error (see Note 7) ±1.75 LSB
DATA INPUT = 1011 2048
Self-test output code (see Table 3 and Note 8) DATA INPUT = 1100 0
DATA INPUT = 1101 4095
t(conv) Conversion time See Figures 914 8 10 µs
tcTotal cycle time (access, sample, and conversion) See Figures 914
and Note 9
10 + total
I/O CLOCK
periods +
td(I/O-EOC)
µs
tacq Channel acquisition time (sample) See Figures 914
and Note 9 4 12 I/O
CLOCK
periods
tvValid time, DATA OUT remains valid after I/O CLOCKSee Figure 6 10 ns
td(I/O-DATA) Delay time, I/O CLOCK to DATA OUT valid See Figure 6 150 ns
td(I/O-EOC) Delay time, last I/O CLOCK to EOCSee Figure 7 1.5 2.2 µs
td(EOC-DATA) Delay time, EOC to DATA OUT (MSB/LSB) See Figure 8 100 ns
tPZH, tPZL Enable time, CS to DATA OUT (MSB/LSB driven) See Figure 3 0.7 1.3 µs
tPHZ, tPLZ Disable time, CS to DATA OUT (high impedance) See Figure 3 70 150 ns
tr(EOC) Rise time, EOC See Figure 8 15 50 ns
tf(EOC) Fall time, EOC See Figure 7 15 50 ns
tr(bus) Rise time, data bus See Figure 6 15 50 ns
tf(bus) Fall time, data bus See Figure 6 15 50 ns
td(I/O-CS) Delay time, last I/O CLOCK to CS to abort conversion
(see Note 10) 5µs
All typical values are at TA = 25°C.
NOTES: 2. Analog input voltages greater than that applied to REF+ convert as all ones (111111111111), while input voltages less than that
applied to REF convert as all zeros (000000000000).
5. Linearity error is the maximum deviation from the best straight line through the A/D transfer characteristics.
6. Gain error is the difference between the actual midstep value and the nominal midstep value in the transfer diagram at the specified
gain point after the of fset error has been adjusted to zero. Of fset error is the difference between the actual midstep value and the
nominal midstep value at the offset point.
7. Total unadjusted error comprises linearity, zero-scale, and full-scale errors.
8. Both the input address and the output codes are expressed in positive logic.
9. I/O CLOCK period = 1/(I/O CLOCK frequency) (see Figure 7).
10. Any transitions of CS are recognized as valid only when the level is maintained for a setup time. CS must be taken low at 5 µs
of the tenth I/O CLOCK falling edge to ensure a conversion is aborted. Between 5 µs and 10 µs, the result is uncertain as to whether
the conversion is aborted or the conversion results are valid.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
7
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
_
+
C2
0.1 µF
C1
10 µFC3
470 pF
50
15 V
50
15 V
VIAIN0AIN10
TLC2543
10
U1
C1
10 µFC3
470 pF
C2
0.1 µF
LOCATION
U1
C1
C2
C3
DESCRIPTION
OP27
10-µF 35-V tantalum capacitor
0.1-µF ceramic NPO SMD capacitor
470-pF porcelain Hi-Q SMD capacitor
PART NUMBER
AVX 12105C104KA105 or equivalent
Johanson 201S420471JG4L or equivalent
Figure 1. Analog Input Buffer to Analog Inputs AIN0AIN10
EOC
CL = 50 pF 12 k
DATA OUT
Test Point VCC
RL = 2.18 k
CL = 100 pF 12 k
Test Point VCC
RL = 2.18 k
Figure 2. Load Circuits
CS
DATA
OUT
2.4 V
0.4 V
90%
10%
tPZH, tPZL tPHZ, tPLZ
0.8 V 2 V
Figure 3. DATA OUT to Hi-Z Voltage Waveforms
DATA INPUT
th(A)
0.8 V
2 V
I/O CLOCK
Data
Valid
tsu(A)
0.8 V
Figure 4. DATA INPUT and I/O CLOCK
Voltage Waveforms
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
8POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
Last
Clock
CS 0.8 V 2 V
0.8 V
tsu(CS)
0.8 V
I/O CLOCK
th(CS)
NOTE A: To ensure full conversion accuracy , it is recommended that no input signal change
occurs while a conversion is ongoing.
Figure 5. CS and I/O CLOCK Voltage Waveforms
0.4 V
2.4 V 0.4 V
2.4 V
2 V 0.8 V
I/O CLOCK
DATA OUT
tt(I/O)
0.8 V
2 V
tr(bus), tf(bus)
td(I/O-DATA)
tv
tt(I/O)
0.8 V
I/O CLOCK Period
Figure 6. I/O CLOCK and DATA OUT Voltage Waveforms
Last
Clock 0.8 V
2.4 V 0.4 V
tf(EOC)
td(I/O-EOC)
I/O CLOCK
EOC
Figure 7. I/O CLOCK and EOC Voltage Waveforms
0.4 V
2.4 V
EOC
td(EOC-DATA)
Valid MSB
DATA OUT
0.4 V 2.4 V
tr(EOC)
Figure 8. EOC and DATA OUT Voltage Waveforms
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
9
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Access Cycle B
Shift in New Multiplexer Address,
Simultaneously Shift Out Previous
Conversion Value
Sample Cycle B
A/D Conversion
Interval InitializeInitialize
MSB LSB
Previous Conversion Data
MSB LSB
B7 B6 B5 B4 C7
B11A11 A10 A9 A8 A7 A6 A5 A4 A1 A0 Hi-Z State
1 2 3 4 5 6 7 8 11 12 1
I/O
CLOCK
DATA
OUT
DATA
INPUT
CS
EOC
(see Note A)
B3 B2 B1 B0
ÎÎÎ
ÎÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Î
Î
Î
Î
Î
Î
ÎÎ
ÎÎ
ÎÎ
ÎÎ
t(conv)
NOTE A: T o minimize errors caused by noise at CS, the internal circuitry waits for a setup time after CS before responding to control input signals.
Therefore, no attempt should be made to clock in an address until the minimum CS setup time has elapsed.
Figure 9. Timing for 12-Clock Transfer Using CS With MSB First
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Access Cycle B
Shift in New Multiplexer Address,
Simultaneously Shift Out Previous
Conversion Value
Sample Cycle B
A/D Conversion
Interval
Initialize
MSB LSB
Previous Conversion Data
MSB LSB
B7 B6 B5 B4 C7
B11A11 A10 A9 A8 A7 A6 A5 A4 A1 A0 Low Level
1 2 3 4 5 6 7 8 11 12 1
I/O
CLOCK
DATA
OUT
DATA
INPUT
CS
EOC
Initialize
(see Note A)
B3 B2 B1 B0
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
t(conv)
NOTE A: T o minimize errors caused by noise at CS, the internal circuitry waits for a setup time after CS before responding to control input signals.
Therefore, no attempt should be made to clock in an address until the minimum CS setup time has elapsed.
Figure 10. Timing for 12-Clock Transfer Not Using CS With MSB First
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
10 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
ÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
Access Cycle B
Shift in New Multiplexer Address,
Simultaneously Shift Out Previous
Conversion Value
Sample Cycle B
A/D Conversion
Interval
Initialize
MSB LSB
Previous Conversion Data
MSB LSB
B7 B6 B5 B4 C7
B7A7 A6 A5 A4 A3 A2 A1 A0
12345678 1
I/O CLOCK
DATA OUT
DATA INPUT
CS
EOC
Initialize
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
Hi-Z
(see Note A)
B3 B2 B1 B0
ÎÎ
ÎÎ
Î
Î
Î
Î
Î
Î
ÎÎ
ÎÎ
ÎÎ
ÎÎ
t(conv)
NOTE A: T o minimize errors caused by noise at CS, the internal circuitry waits for a setup time after CS before responding to control input signals.
Therefore, no attempt should be made to clock in an address until the minimum CS setup time has elapsed.
Figure 11. Timing for 8-Clock Transfer Using CS With MSB First
ÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Access Cycle B Sample Cycle B
A/D Conversion
Interval
Initialize
MSB LSB
Previous Conversion Data
MSB LSB
B7 B6 B5 B4 C7
B7A7 A6 A5 A4 A3 A2 A1 A0 Low Level
12345678 1
I/O CLOCK
DATA OUT
DATA INPUT
CS
EOC
Initialize
(see Note A)
ÎÎ
ÎÎ
B3 B2 B1 B0
Î
Î
Î
Î
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
t(conv)
Shift in New Multiplexer Address,
Simultaneously Shift Out Previous
Conversion Value
NOTE A: T o minimize errors caused by noise at CS, the internal circuitry waits for a setup time after CS before responding to control input signals.
Therefore, no attempt should be made to clock in an address until the minimum CS setup time has elapsed.
Figure 12. Timing for 8-Clock Transfer Not Using CS With MSB First
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
11
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
ÎÎ
ÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Î
ÎÎ
ÎÎ
A/D Conversion
Interval
Initialize
MSB LSB
MSB LSB
B7 B6 B5 B4 C7
B15A15 A14 A13 A12 A11 A10 A9 A8 A1 A0
1 2 3 4 5 6 7 8 15 16 1
I/O
CLOCK
DATA
OUT
DATA
INPUT
CS
EOC
Initialize
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
Hi-Z State
(see Note A)
B3 B2 B1 B0
Access Cycle B Sample Cycle B
Previous Conversion Data
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
t(conv)
Shift in New Multiplexer Address,
Simultaneously Shift Out Previous
Conversion Value
NOTE A: T o minimize errors caused by noise at CS, the internal circuitry waits for a setup time after CS before responding to control input signals.
Therefore, no attempt should be made to clock in an address until the minimum CS setup time has elapsed.
Figure 13. Timing for 16-Clock Transfer Using CS With MSB First
Î
Î
ÎÎ
ÎÎ
ÎÎ
ÎÎ
Î
Î
ÎÎÎÎ
ÎÎÎÎ
A/D Conversion
Interval
Initialize
MSB LSB
MSB LSB
B7 B6 B5 B4 C7
B15A15 A14 A13 A12 A11 A10 A9 A8 A1 A0
1 2 3 4 5 6 7 8 15 16 1
I/O
CLOCK
DATA
OUT
DATA
INPUT
CS
EOC
Low Level
(see Note A)
B3 B2 B1 B0
Sample Cycle B
Access Cycle B
Previous Conversion Data
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎ
t(conv)
Shift in New Multiplexer Address,
Simultaneously Shift Out Previous
Conversion Value
NOTE A: T o minimize errors caused by noise at CS, the internal circuitry waits for a setup time after CS before responding to control input signals.
Therefore, no attempt should be made to clock in an address until the minimum CS setup time has elapsed.
Figure 14. Timing for 16-Clock Transfer Not Using CS With MSB First
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
12 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
Initially, with chip select (CS) high, I/O CLOCK and DATA INPUT are disabled and DATA OUT is in the
high-impedance state. CS going low begins the conversion sequence by enabling I/O CLOCK and DAT A INPUT
and removes DATA OUT from the high-impedance state.
The input data is an 8-bit data stream consisting of a 4-bit analog channel address (D7D4), a 2-bit data length
select (D3D2), an output MSB or LSB first bit (D1), and a unipolar or bipolar output select bit (D0) that are
applied to DA T A INPUT. The I/O CLOCK sequence applied to the I/O CLOCK terminal transfers this data to the
input data register.
During this transfer, the I/O CLOCK sequence also shifts the previous conversion result from the output data
register to DATA OUT. I/O CLOCK receives the input sequence of 8, 12, or 16 clock cycles long depending on
the data-length selection in the input data register. Sampling of the analog input begins on the fourth falling edge
of the input I/O CLOCK sequence and is held after the last falling edge of the I/O CLOCK sequence. The last
falling edge of the I/O CLOCK sequence also takes EOC low and begins the conversion.
converter operation
The operation of the converter is organized as a succession of two distinct cycles: 1) the I/O cycle and 2) the
actual conversion cycle.
I/O cycle
The I/O cycle is defined by the externally provided I/O CLOCK and lasts 8, 12, or 16 clock periods, depending
on the selected output data length.
During the I/O cycle, the following two operations take place simultaneously.
An 8-bit data stream consisting of address and control information is provided to DATA INPUT. This data is
shifted into the device on the rising edge of the first eight I/O CLOCKs. DATA INPUT is ignored after the first
eight clocks during 12- or 16-clock I/O transfers.
The data output, with a length of 8, 12, or 16 bits, is provided serially on DATA OUT. When CS is held low, the
first output data bit occurs on the rising edge of EOC. When CS is negated between conversions, the first output
data bit occurs on the falling edge of CS. This data is the result of the previous conversion period, and after the
first output data bit, each succeeding bit is clocked out on the falling edge of each succeeding I/O CLOCK.
conversion cycle
The conversion cycle is transparent to the user, and it is controlled by an internal clock synchronized to
I/O CLOCK. During the conversion period, the device performs a successive-approximation conversion on the
analog input voltage. The EOC output goes low at the start of the conversion cycle and goes high when
conversion is complete and the output data register is latched. A conversion cycle is started only after the I/O
cycle is completed, which minimizes the influence of external digital noise on the accuracy of the conversion.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
13
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
power up and initialization
After power up, CS must be taken from high to low to begin an I/O cycle. EOC is initially high, and the input data
register is set to all zeroes. The contents of the output data register are random, and the first conversion result
should be ignored. To initialize during operation, CS is taken high and is then returned low to begin the next I/O
cycle. The first conversion after the device has returned from the power-down state may not read accurately
due to internal device settling.
Table 1. Operational Terminology
Current (N) I/O cycle The entire I/O CLOCK sequence that transfers address and control data into the data register and clocks
the digital result from the previous conversion from DATA OUT
Current (N) conversion cycle The conversion cycle starts immediately after the current I/O cycle. The end of the current I/O cycle is the
last clock falling edge in the I/O CLOCK sequence. The current conversion result is loaded into the output
register when conversion is complete.
Current (N) conversion result The current conversion result is serially shifted out on the next I/O cycle.
Previous (N1) conversion cycle The conversion cycle just prior to the current I/O cycle
Next (N+1) I/O cycle The I/O period that follows the current conversion cycle
Example: In the 12-bit mode, the result of the current conversion cycle is a 12-bit serial-data stream clocked out during
the next I/O cycle. The current I/O cycle must be exactly 12 bits long to maintain synchronization, even
when this corrupts the output data from the previous conversion. The current conversion is begun
immediately after the twelfth falling edge of the current I/O cycle.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
14 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
data input
The data input is internally connected to an 8-bit serial-input address and control register . The register defines
the operation of the converter and the output data length. The host provides the data word with the MSB first.
Each data bit is clocked in on the rising edge of the I/O CLOCK sequence (see Table 2 for the data input-register
format).
Table 2. Input-Register Format
INPUT DATA BYTE
FUNCTION SELECT
ADDRESS BITS L1 L0 LSBF BIP
FUNCTION
SELECT
D7
(MSB) D6 D5 D4 D3 D2 D1 D0
(LSB)
Select input channel
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
Select test voltage
(Vref+ Vref)/2
V ref
V ref+
1
1
1
0
1
1
1
0
0
1
0
1
Software power down 1110
Output data length
8 bits
12 bits
16 bits
0
X
1
1
0
1
Output data format
MSB first
LSB first (LSBF) 0
1
Unipolar (binary) 0
Bipolar (BIP) 2s complement 1
X represents a do not care condition.
data input address bits
The four MSBs (D7 D4) of the data register address one of the 11 input channels, a reference-test voltage,
or the power-down mode. The address bits affect the current conversion, which is the conversion that
immediately follows the current I/O cycle. The reference voltage is nominally equal to Vref+ Vref.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
15
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
data output length
The next two bits (D3 and D2) of the data register select the output data length. The data-length selection is
valid for the current I/O cycle (the cycle in which the data is read). The data-length selection, being valid for the
current I/O cycle, allows device start-up without losing I/O synchronization. A data length of 8, 12, or 16 bits can
be selected. Since the converter has 12-bit resolution, a data length of 12 bits is suggested.
With D3 and D2 set to 00 or 10, the device is in the 12-bit data-length mode and the result of the current
conversion is output as a 12-bit serial data stream during the next I/O cycle. The current I/O cycle must be exactly
12 bits long for proper synchronization, even when this means corrupting the output data from a previous
conversion. The current conversion is started immediately after the twelfth falling edge of the current I/O cycle.
With bits D3 and D2 set to 1 1, the 16-bit data-length mode is selected, which allows convenient communication
with 16-bit serial interfaces. In the 16-bit mode, the result of the current conversion is output as a 16-bit serial
data stream during the next I/O cycle with the four LSBs always reset to 0 (pad bits). The current I/O cycle must
be exactly 16 bits long to maintain synchronization even when this means corrupting the output data from the
previous conversion. The current conversion is started immediately after the sixteenth falling edge of the current
I/O cycle.
With bits D3 and D2 set to 01, the 8-bit data-length mode is selected, which allows fast communication with 8-bit
serial interfaces. In the 8-bit mode, the result of the current conversion is output as an 8-bit serial data stream
during the next I/O cycle. The current I/O cycle must be exactly eight bits long to maintain synchronization, even
when this means corrupting the output data from the previous conversion. The four LSBs of the conversion
result are truncated and discarded. The current conversion is started immediately after the eighth falling edge
of the current I/O cycle.
Since D3 and D2 take effect on the current I/O cycle when the data length is programmed, there can be a conflict
with the previous cycle when the data-word length is changed from one cycle to the next. This may occur when
the data format is selected to be least significant bit first, since at the time the data length change becomes
effective (six rising edges of I/O CLOCK), the previous conversion result has already started shifting out.
In actual operation, when different data lengths are required within an application and the data length is changed
between two conversions, no more than one conversion result can be corrupted and only when it is shifted out
in LSB-first format.
sampling period
During the sampling period, one of the analog inputs is internally connected to the capacitor array of the
converter to store the analog input signal. The converter starts sampling the selected input immediately after
the four address bits have been clocked into the input data register. Sampling starts on the fourth falling edge
of I/O CLOCK. The converter remains in the sampling mode until the eighth, twelfth, or sixteenth falling edge
of the I/O CLOCK depending on the data-length selection. After the EOC delay time from the last I/O CLOCK
falling edge, the EOC output goes low indicating that the sampling period is over and the conversion period has
begun. After EOC goes low , the analog input can be changed without affecting the conversion result. Since the
delay from the falling edge of the last I/O CLOCK to EOC low is fixed, time-varying analog input signals can be
digitized at a fixed rate without introducing systematic harmonic distortion or noise due to timing uncertainty.
After the 8-bit data stream has been clocked in, DATA INPUT should be held at a fixed digital level until EOC
goes high (indicating that the conversion is complete) to maximize the sampling accuracy and minimize the
influence of external digital noise.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
16 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
data register, LSB first
D1 in the input data register (LSB first) controls the direction of the output binary data transfer. When D1 is reset
to 0, the conversion result is shifted out MSB first. When set to 1, the data is shifted out LSB first. Selection of
MSB first or LSB first always affects the next I/O cycle and not the current I/O cycle. When changing from one
data direction to another, the current I/O cycle is never disrupted.
data register, bipolar format
D0 (BIP) in the input data register controls the binary data format used to represent the conversion result. When
D0 is cleared to 0, the conversion result is represented as unipolar (unsigned binary) data. Nominally, the
conversion result of an input voltage equal to Vref is a code of all zeros (000 . . . 0), the conversion result of
an input voltage equal to V ref+ is a code of all ones (111 . . . 1), and the conversion result of (Vref + + Vref)/2
is a code of a one followed by zeros (100 ...0).
When D0 is set to 1, the conversion result is represented as bipolar (signed binary) data. Nominally , conversion
of an input voltage equal to Vref is a code of a one followed by zeros (100 . . . 0), conversion of an input voltage
equal to V ref+ is a code of a zero followed by all ones (011 . . . 1), and the conversion of (V ref+ + V ref)/2 is a
code of all zeros (000 . . . 0). The MSB is interpreted as the sign bit. The bipolar data format is related to the
unipolar format in that the MSBs are always each others complement.
Selection of the unipolar or bipolar format always af fects the current conversion cycle, and the result is output
during the next I/O cycle. When changing between unipolar and bipolar formats, the data output during the
current I/O cycle is not affected.
EOC output
The EOC signal indicates the beginning and the end of conversion. In the reset state, EOC is always high. During
the sampling period (beginning after the fourth falling edge of the I/O CLOCK sequence), EOC remains high
until the internal sampling switch of the converter is safely opened. The opening of the sampling switch occurs
after the eighth, twelfth, or sixteenth I/O CLOCK falling edge, depending on the data-length selection in the input
data register. After the EOC signal goes low, the analog input signal can be changed without affecting the
conversion result.
The EOC signal goes high again after the conversion is completed and the conversion result is latched into the
output data register . The rising edge of EOC returns the converter to a reset state and a new I/O cycle begins.
On the rising edge of EOC, the first bit of the current conversion result is on DATA OUT when CS is low . When
CS is negated between conversions, the first bit of the current conversion result occurs at DATA OUT on the
falling edge of CS.
data format and pad bits
D3 and D2 of the input data register determine the number of significant bits in the digital output that represent
the conversion result. The LSB-first bit determines the direction of the data transfer while the BIP bit determines
the arithmetic conversion. The numerical data is always justified toward the MSB in any output format.
The internal conversion result is always 12 bits long. When an 8-bit data transfer is selected, the four LSBs of
the internal result are discarded to provide a faster one-byte transfer . When a 12-bit transfer is used, all bits are
transferred. When a 16-bit transfer is used, four LSB pad bits are always appended to the internal conversion
result. In the LSB-first mode, four leading zeros are output. In the MSB-first mode, the last four bits output are
zeros.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
17
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
data format and pad bits (continued)
When CS is held low continuously, the first data bit of the newly completed conversion occurs on DATA OUT
on the rising edge of EOC. When a new conversion is started after the last falling edge of I/O CLOCK, EOC goes
low and the serial output is forced to a setting of 0 until EOC goes high again.
When CS is negated between conversions, the first data bit occurs on DATA OUT on the falling edge of CS.
On each subsequent falling edge of I/O CLOCK after the first data bit appears, the data is changed to the next
bit in the serial conversion result until the required number of bits has been output.
chip-select input (CS)
CS enables and disables the device. During normal operation, CS should be low . Although the use of CS is not
necessary to synchronize a data transfer, it can be brought high between conversions to coordinate the data
transfer of several devices sharing the same bus.
When CS is brought high, the serial-data output is immediately brought to the high-impedance state, releasing
its output data line to other devices that may share it. After an internally generated debounce time, I/O CLOCK
is inhibited, thus preventing any further change in the internal state.
When CS is subsequently brought low again, the device is reset. CS must be held low for an internal debounce
time before the reset operation takes effect. After CS is debounced low , I/O CLOCK must remain inactive (low)
for a minimum time before a new I/O cycle can start.
CS can interrupt any ongoing data transfer or any ongoing conversion. When CS is debounced low long enough
before the end of the current conversion cycle, the previous conversion result is saved in the internal output
buffer and shifted out during the next I/O cycle.
power-down features
When a binary address of 1110 is clocked into the input data register during the first four I/O CLOCK cycles,
the power-down mode is selected. Power down is activated on the falling edge of the fourth I/O CLOCK pulse.
During power down, all internal circuitry is put in a low-current standby mode. No conversions are performed,
and the internal output buffer keeps the previous conversion cycle data results provided that all digital inputs
are held above VCC 0.5 V or below 0.5 V. The I/O logic remains active so the current I/O cycle must be
completed even when the power-down mode is selected. Upon power-on reset and before the first I/O cycle,
the converter normally begins in the power-down mode. The device remains in the power-down mode until a
valid input address (other than 1110) is clocked in. Upon completion of that I/O cycle, a normal conversion is
performed with the results being shifted out during the next I/O cycle.
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
18 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
analog input, test, and power-down mode
The 11 analog inputs, three internal voltages, and power-down mode are selected by the input multiplexer
according to the input addresses shown in T ables 2, 3, and 4. The input multiplexer is a break-before-make type
to reduce input-to-input noise rejection resulting from channel switching. Sampling of the analog input starts on
the falling edge of the fourth I/O CLOCK and continues for the remaining I/O CLOCK pulses. The sample is held
on the falling edge of the last I/O CLOCK pulse. The three internal test inputs are applied to the multiplexer, then
sampled and converted in the same manner as the external analog inputs. The first conversion after the device
has returned from the power-down state may not read accurately due to internal device settling.
Table 3. Analog-Channel-Select Address
ANALOG INPUT
SELECTED
VALUE SHIFTED INTO
DATA INPUT
SELECTED
BINARY HEX
AIN0 0000 0
AIN1 0001 1
AIN2 0010 2
AIN3 0011 3
AIN4 0100 4
AIN5 0101 5
AIN6 0110 6
AIN7 0111 7
AIN8 1000 8
AIN9 1001 9
AIN10 1010 A
Table 4. Test-Mode-Select Address
INTERNAL
SELF-TEST
VOLTAGE
VALUE SHIFTED INTO
DATA INPUT UNIPOLAR OUTPUT
RESULT (HEX)
VOLTAGE
SELECTEDBINARY HEX
RESULT
(HEX)
Vref+ Vref
21011 B 800
Vref1100 C 000
Vref+ 1101 D FFF
Vref+ is the voltage applied to REF+, and Vref is the voltage applied to REF.
The output results shown are the ideal values and may vary with the reference stability
and with internal offsets.
Table 5. Power-Down-Select Address
INPUT COMMAND VALUE SHIFTED INTO
DATA INPUT RESULT
BINARY HEX
Power down 1110 E ICC 25 µA
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
19
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
converter and analog input
The CMOS threshold detector in the successive-approximation conversion system determines each bit by
examining the charge on a series of binary-weighted capacitors (see Figure 1). In the first phase of the
conversion process, the analog input is sampled by closing the SC switch and all ST switches simultaneously .
This action charges all the capacitors to the input voltage.
In the next phase of the conversion process, all ST and SC switches are opened and the threshold detector
begins identifying bits by identifying the charge (voltage) on each capacitor relative to the reference (REF)
voltage. In the switching sequence, 12 capacitors are examined separately until all 12 bits are identified and
the charge-convert sequence is repeated. In the first step of the conversion phase, the threshold detector looks
at the first capacitor (weight = 4096). Node 4096 of this capacitor is switched to the REF+ voltage, and the
equivalent nodes of all the other capacitors on the ladder are switched to REF . When the voltage at the
summing node is greater than the trip point of the threshold detector (approximately 1/2 VCC), a bit 0 is placed
in the output register and the 4096-weight capacitor is switched to REF. When the voltage at the summing node
is less than the trip point of the threshold detector , a bit 1 is placed in the register and this 4096-weight capacitor
remains connected to REF+ through the remainder of the successive-approximation process. The process is
repeated for the 2048-weight capacitor, the 1024-weight capacitor, and so forth down the line until all bits are
determined. With each step of the successive-approximation process, the initial charge is redistributed among
the capacitors. The conversion process relies on charge redistribution to determine the bits from MSB to LSB.
reference voltage inputs
The two reference inputs used with the device are the voltages applied to the REF+ and REF terminals. These
voltage values establish the upper and lower limits of the analog input to produce a full-scale and zero-scale
reading respectively. These voltages and the analog input should not exceed the positive supply or be lower
than ground consistent with the specified absolute maximum ratings. The digital output is at full scale when the
input signal is equal to or higher than REF+ terminal voltage and at zero when the input signal is equal to or lower
than REF terminal voltage. SC
Threshold
Detector
Node 4096
REF
REF+
ST
4096
VI
To Output
Latches
REF
ST
REF+
REF
ST
REF+
REF
ST
REF+
REF
ST
REF+
REF
ST
REF+
REF
ST
REF+
REF
ST
REF
ST
112481610242048
Figure 15. Simplified Model of the Successive-Approximation System
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
20 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
APPLICATION INFORMATION
100000000000
011111111111
000000000010
000000000001
000000000000
111111111110
0 0.0024 2.4564 2.4576 2.4588
Digital Output Code
100000000001
111111111101
111111111111
4.9128 4.9140 4.9152
2048
2047
2
1
0
4094
Step
2049
4093
4095
0.0006
VI Analog Input Voltage V
VZT = VZS + 1/2 LSB
VZS
See Notes A and B
4.9134
0.0012
VFT = VFS 1/2 LSB
VFS
VFSnom
NOTES: A. This curve is based on the assumption that Vref+ and Vref have been adjusted so that the voltage at the transition from digital 0
to 1 (VZT) is 0.0006 V and the transition to full scale (VFT) is 4.9134 V. 1 LSB = 1.2 mV.
B. The full-scale value (VFS) is the step whose nominal midstep value has the highest absolute value. The zero-scale value (VZS) is
the step whose nominal midstep value equals zero.
Figure 16. Ideal Conversion Characteristics
Processor Control
Circuit
Analog
Inputs
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
AIN9
AIN10
I/O CLOCK
CS
DATA INPUT
DATA OUT
EOC
REF+
REF
GND
TLC2543
To Source
Ground
5-V DC Regulated
1
2
3
4
5
6
7
8
9
11
12
15
18
17
16
19
14
13
10
Figure 17. Serial Interface
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
21
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
APPLICATION INFORMATION
simplified analog input analysis
Using the equivalent circuit in Figure 18, the time required to charge the analog input capacitance from 0 V to
VS within 1/2 LSB can be derived as follows:
The capacitance charging voltage is given by
(1
)
Where: Rt = Rs + ri
VC
+
VS
ǒ
1etc
ń
RtCi
Ǔ
The final voltage to 1/2 LSB is given by
(2)VC (1/2 LSB) = VS (VS/8192)
Equating equation 1 to equation 2 and solving for time tc gives
(3
)
and tc (1/2 LSB) = Rt × Ci × ln(8192) (4
)
VS
*ǒ
VS
ń
8192
Ǔ+
VS
ǒ
1etc
ń
RtCi
Ǔ
Therefore, with the values given, the time for the analog input signal to settle is
(5)
tc (1/2 LSB) = (Rs + 1 k) × 60 pF × ln(8192)
This time must be less than the converter sample time shown in the timing diagrams.
Rsri
VSVC
60 pF Max
1 k Max
Driving SourceTLC2543
Ci
VI
VI= Input Voltage at AIN
VS= External Driving Source Voltage
Rs= Source Resistance
ri= Input Resistance
Ci= Input Capacitance
VC= Capacitance Charging Voltage
Driving source requirements:
Noise and distortion for the source must be equivalent to the
resolution of the converter.
Rs must be real at the input frequency.
Figure 18. Equivalent Input Circuit Including the Driving Source
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
22 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
4040065 /C 10/95
28 PIN SHOWN
Gage Plane
8,20
7,40
0,15 NOM
0,63
1,03
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°8°
0,10
3,30
8
2,70
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
23
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
MECHANICAL INFORMATION
DW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
16 PIN SHOWN
4040000/B 03/95
Seating Plane
0.400 (10,15)
0.419 (10,65)
0.104 (2,65) MAX
1
0.012 (0,30)
0.004 (0,10)
A
8
16
0.020 (0,51)
0.014 (0,35)
0.293 (7,45)
0.299 (7,59)
9
0.010 (0,25)
0.050 (1,27)
0.016 (0,40)
(15,24)
(15,49)
PINS **
0.010 (0,25) NOM
A MAX
DIM
A MIN
Gage Plane
20
0.500
(12,70)
(12,95)
0.510
(10,16)
(10,41)
0.400
0.410
16
0.600
24
0.610
(17,78)
28
0.700
(18,03)
0.710
0.004 (0,10)
M
0.010 (0,25)
0.050 (1,27)
0°8°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-013
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
24 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
MECHANICAL INFORMATION
FN (S-PQCC-J**) PLASTIC J-LEADED CHIP CARRIER
4040005/B 03/95
20 PIN SHOWN
0.026 (0,66)
0.032 (0,81)
D2/E2
0.020 (0,51) MIN
0.180 (4,57) MAX
0.120 (3,05)
0.090 (2,29)
D2/E2
0.013 (0,33)
0.021 (0,53)
Seating Plane
MAX
D2/E2
0.219 (5,56)
0.169 (4,29)
0.319 (8,10)
0.469 (11,91)
0.569 (14,45)
0.369 (9,37)
MAX
0.356 (9,04)
0.456 (11,58)
0.656 (16,66)
0.008 (0,20) NOM
1.158 (29,41)
0.958 (24,33)
0.756 (19,20)
0.191 (4,85)
0.141 (3,58)
MIN
0.441 (11,20)
0.541 (13,74)
0.291 (7,39)
0.341 (8,66)
18
19
14
13
D
D1
13
9
E1E
4
8
MINMAXMIN
PINS
**
20
28
44
0.385 (9,78)
0.485 (12,32)
0.685 (17,40)
52
68
84 1.185 (30,10)
0.985 (25,02)
0.785 (19,94)
D/E
0.395 (10,03)
0.495 (12,57)
1.195 (30,35)
0.995 (25,27)
0.695 (17,65)
0.795 (20,19)
NO. OF D1/E1
0.350 (8,89)
0.450 (11,43)
1.150 (29,21)
0.950 (24,13)
0.650 (16,51)
0.750 (19,05)
0.004 (0,10)
M
0.007 (0,18)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-018
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
25
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
MECHANICAL INFORMATION
J (R-GDIP-T**) CERAMIC DUAL-IN-LINE PACKAGE
14 PIN SHOWN
20
0.290
(7,87)
0.310
0.975
(24,77)
(23,62)
0.930
(7,37)
0.245
(6,22)
(7,62)
0.300
181614
PINS **
0.290
(7,87)
0.310
0.785
(19,94)
(19,18)
0.755
(7,37)
0.310
(7,87)
(7,37)
0.290
0.755
(19,18)
(19,94)
0.785
0.245
(6,22)
(7,11)
0.280
A
0.300
(7,62)
(6,22)
0.245
A MIN
A MAX
B MAX
B MIN
C MIN
C MAX
DIM
0.310
(7,87)
(7,37)
0.290
(23,10)
0.910
0.300
(7,62)
(6,22)
0.245
Seating Plane
0.014 (0,36)
0.008 (0,20) 4040083/C 08/96
C
8
7
0.020 (0,51) MIN
B
0.070 (1,78)
0.100 (2,54)
0.065 (1,65)
0.045 (1,14)
14
1
0.015 (0,38)
0.023 (0,58)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.100 (2,54) 0°15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.
E. Falls within MIL-STD-1835 GDIP1-T14, GDIP1-T16, GDIP1-T18, and GDIP1-T20
TLC2543C, TLC2543I, TLC2543M
12-BIT ANALOG-TO-DIGITAL CONVERTERS
WITH SERIAL CONTROL AND 11 ANALOG INPUTS
SLAS079F DECEMBER 1993 REVISED NOVEMBER 2001
26 POST OFFICE BOX 655303 DALLAS, TEXAS 75265
MECHANICAL INFORMATION
N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE
20
0.975
(24,77)
0.940
(23,88)
18
0.920
0.850
14
0.775
0.745
(19,69)
(18,92)
16
0.775
(19,69)
(18,92)
0.745
A MIN
DIM
A MAX
PINS **
0.310 (7,87)
0.290 (7,37)
(23.37)
(21.59)
Seating Plane
0.010 (0,25) NOM
14/18 PIN ONLY
4040049/C 08/95
9
8
0.070 (1,78) MAX
A
0.035 (0,89) MAX 0.020 (0,51) MIN
16
1
0.015 (0,38)
0.021 (0,53)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.240 (6,10)
0.260 (6,60)
M
0.010 (0,25)
0.100 (2,54) 0°15°
16 PIN SHOWN
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.)
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
5962-9688601QRA ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type
TLC2543CDB ACTIVE SSOP DB 20 70 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDBG4 ACTIVE SSOP DB 20 70 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDBLE OBSOLETE SSOP DB 20 TBD Call TI Call TI
TLC2543CDBR ACTIVE SSOP DB 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDW ACTIVE SOIC DW 20 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDWG4 ACTIVE SOIC DW 20 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDWR ACTIVE SOIC DW 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CDWRG4 ACTIVE SOIC DW 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543CFN ACTIVE PLCC FN 20 46 Green (RoHS &
no Sb/Br) CU SN Level-1-260C-UNLIM
TLC2543CFNG3 ACTIVE PLCC FN 20 46 Green (RoHS &
no Sb/Br) CU SN Level-1-260C-UNLIM
TLC2543CFNR ACTIVE PLCC FN 20 1000 Green (RoHS &
no Sb/Br) CU SN Level-1-260C-UNLIM
TLC2543CFNRG3 ACTIVE PLCC FN 20 1000 Green (RoHS &
no Sb/Br) CU SN Level-1-260C-UNLIM
TLC2543CN ACTIVE PDIP N 20 20 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
TLC2543CNE4 ACTIVE PDIP N 20 20 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
TLC2543IDB ACTIVE SSOP DB 20 70 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDBG4 ACTIVE SSOP DB 20 70 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDBR ACTIVE SSOP DB 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDW ACTIVE SOIC DW 20 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDWG4 ACTIVE SOIC DW 20 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDWR ACTIVE SOIC DW 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IDWRG4 ACTIVE SOIC DW 20 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2543IFN ACTIVE PLCC FN 20 46 Green (RoHS &
no Sb/Br) CU SN Level-1-260C-UNLIM
TLC2543IFNG3 ACTIVE PLCC FN 20 46 Green (RoHS & CU SN Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 15-Oct-2009
Addendum-Page 1
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
no Sb/Br)
TLC2543IFNR OBSOLETE PLCC FN 20 TBD Call TI Call TI
TLC2543IN ACTIVE PDIP N 20 20 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
TLC2543INE4 ACTIVE PDIP N 20 20 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
TLC2543MJ ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type
TLC2543MJB ACTIVE CDIP J 20 1 TBD A42 N / A for Pkg Type
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC2543, TLC2543M :
Automotive: TLC2543-Q1
Enhanced Product: TLC2543-EP
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Enhanced Product - Supports Defense, Aerospace and Medical Applications
PACKAGE OPTION ADDENDUM
www.ti.com 15-Oct-2009
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
TLC2543CDBR SSOP DB 20 2000 330.0 16.4 8.2 7.5 2.5 12.0 16.0 Q1
TLC2543IDBR SSOP DB 20 2000 330.0 16.4 8.2 7.5 2.5 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 9-Apr-2009
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TLC2543CDBR SSOP DB 20 2000 346.0 346.0 33.0
TLC2543IDBR SSOP DB 20 2000 346.0 346.0 33.0
PACKAGE MATERIALS INFORMATION
www.ti.com 9-Apr-2009
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
MECHANICAL DATA
MPLC004A – OCTOBER 1994
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
FN (S-PQCC-J**) PLASTIC J-LEADED CHIP CARRIER
4040005/B 03/95
20 PIN SHOWN
0.026 (0,66)
0.032 (0,81)
D2/E2
0.020 (0,51) MIN
0.180 (4,57) MAX
0.120 (3,05)
0.090 (2,29)
D2/E2
0.013 (0,33)
0.021 (0,53)
Seating Plane
MAX
D2/E2
0.219 (5,56)
0.169 (4,29)
0.319 (8,10)
0.469 (11,91)
0.569 (14,45)
0.369 (9,37)
MAX
0.356 (9,04)
0.456 (11,58)
0.656 (16,66)
0.008 (0,20) NOM
1.158 (29,41)
0.958 (24,33)
0.756 (19,20)
0.191 (4,85)
0.141 (3,58)
MIN
0.441 (11,20)
0.541 (13,74)
0.291 (7,39)
0.341 (8,66)
18
19
14
13
D
D1
13
9
E1E
4
8
MINMAXMIN
PINS
**
20
28
44
0.385 (9,78)
0.485 (12,32)
0.685 (17,40)
52
68
84 1.185 (30,10)
0.985 (25,02)
0.785 (19,94)
D/E
0.395 (10,03)
0.495 (12,57)
1.195 (30,35)
0.995 (25,27)
0.695 (17,65)
0.795 (20,19)
NO. OF D1/E1
0.350 (8,89)
0.450 (11,43)
1.150 (29,21)
0.950 (24,13)
0.650 (16,51)
0.750 (19,05)
0.004 (0,10)
M
0.007 (0,18)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-018
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDLP® Products www.dlp.com Broadband www.ti.com/broadbandDSP dsp.ti.com Digital Control www.ti.com/digitalcontrolClocks and Timers www.ti.com/clocks Medical www.ti.com/medicalInterface interface.ti.com Military www.ti.com/militaryLogic logic.ti.com Optical Networking www.ti.com/opticalnetworkPower Mgmt power.ti.com Security www.ti.com/securityMicrocontrollers microcontroller.ti.com Telephony www.ti.com/telephonyRFID www.ti-rfid.com Video & Imaging www.ti.com/videoRF/IF and ZigBee® Solutions www.ti.com/lprf Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2009, Texas Instruments Incorporated