DS90CR285,DS90CR286 DS90CR285/DS90CR286 +3.3V Rising Edge Data Strobe LVDS 28-Bit Channel Link-66 MHz Literature Number: SNLS130B DS90CR285/DS90CR286 +3.3V Rising Edge Data Strobe LVDS 28-Bit Channel Link-66 MHz General Description The DS90CR285 transmitter converts 28 bits of LVCMOS/ LVTTL data into four LVDS (Low Voltage Differential Signaling) data streams. A phase-locked transmit clock is transmitted in parallel with the data streams over a fifth LVDS link. Every cycle of the transmit clock 28 bits of input data are sampled and transmitted. The DS90CR286 receiver converts the LVDS data streams back into 28 bits of LVCMOS/ LVTTL data. At a transmit clock frequency of 66 MHz, 28 bits of TTL data are transmitted at a rate of 462 Mbps per LVDS data channel. Using a 66 MHz clock, the data throughput is 1.848 Gbit/s (231 Mbytes/s). The multiplexing of the data lines provides a substantial cable reduction. Long distance parallel single-ended buses typically require a ground wire per active signal (and have very limited noise rejection capability). Thus, for a 28-bit wide data and one clock, up to 58 conductors are required. With the Channel Link chipset as few as 11 conductors (4 data pairs, 1 clock pair and a minimum of one ground) are needed. This provides a 80% reduction in required cable width, which provides a system cost savings, reduces connector physical size and cost, and reduces shielding requirements due to the cables' smaller form factor. The 28 LVCMOS/LVTTL inputs can support a variety of signal combinations. For example, seven 4-bit nibbles or three 9-bit (byte + parity) and 1 control. Features n n n n n n n n n n n n n n Single +3.3V supply Chipset (Tx + Rx) power consumption < 250 mW (typ) Power-down mode ( < 0.5 mW total) Up to 231 Megabytes/sec bandwidth Up to 1.848 Gbps data throughput Narrow bus reduces cable size 290 mV swing LVDS devices for low EMI +1V common mode range (around +1.2V) PLL requires no external components Both devices are offered in a Low profile 56-lead TSSOP package Rising edge data strobe Compatible with TIA/EIA-644 LVDS standard ESD Rating > 7 kV Operating Temperature: -40C to +85C Block Diagrams DS90CR285 DS90CR286 01291001 Order Number DS90CR285MTD See NS Package Number MTD56 01291027 Order Number DS90CR286MTD See NS Package Number MTD56 TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2004 National Semiconductor Corporation DS012910 www.national.com DS90CR285/DS90CR286 +3.3V Rising Edge Data Strobe LVDS 28-Bit Channel Link-66 MHz July 2004 DS90CR285/DS90CR286 Pin Diagrams for TSSOP Packages DS90CR285 DS90CR286 01291021 01291022 Typical Application 01291023 www.national.com 2 Maximum Package Power Dissipation @ +25C If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) -0.3V to (VCC + 0.3V) CMOS/TTL Output Voltage -0.3V to (VCC + 0.3V) LVDS Receiver Input Voltage -0.3V to (VCC + 0.3V) LVDS Driver Output Voltage -0.3V to (VCC + 0.3V) 1.63 W DS90CR286MTD 1.61 W Package Derating: -0.3V to +4V CMOS/TTL Input Voltage DS90CR285MTD DS90CR285MTD 12.5 mW/C above +25C DS90CR286MTD 12.4 mW/C above +25C ESD Rating > 7 kV (HBM, 1.5 k, 100 pF) Recommended Operating Conditions LVDS Output Short Circuit Duration Continuous Junction Temperature +150C Storage Temperature -65C to +150C Supply Voltage (VCC) Nom Max Units 3.0 3.3 3.6 V +25 +85 C 2.4 V Operating Free Air Lead Temperature Temperature (TA) (Soldering, 4 sec.) Min +260C -40 Receiver Input Range Solder Reflow Temperature 0 Supply Noise Voltage (VCC) 100 mVPP Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified Symbol Parameter Conditions Min Typ Max Units LVCMOS/LVTTL DC SPECIFICATIONS VIH High Level Input Voltage 2.0 VCC V VIL Low Level Input Voltage GND 0.8 V VOH High Level Output Voltage IOH = -0.4 mA VOL Low Level Output Voltage IOL = 2 mA VCL Input Clamp Voltage ICL = -18 mA IIN Input Current IOS Output Short Circuit Current 2.7 3.3 V 0.06 0.3 V -0.79 -1.5 V VIN = VCC, GND, 2.5V or 0.4V 5.1 10 A VOUT = 0V -60 -120 mA 290 450 mV 35 mV LVDS DRIVER DC SPECIFICATIONS VOD Differential Output Voltage VOD Change in VOD between Complimentary Output States RL = 100 250 VOS Offset Voltage (Note 4) VOS Change in VOS between Complimentary Output States 1.125 IOS Output Short Circuit Current VOUT = 0V, RL = 100 IOZ Output TRI-STATE (R) Current PWR DWN = 0V, 1.25 1.375 V 35 mV -3.5 -5 mA 1 10 A VOUT = 0V or VCC LVDS RECEIVER DC SPECIFICATIONS VTH Differential Input High Threshold VTL Differential Input Low Threshold IIN Input Current VCM = +1.2V +100 -100 VIN = +2.4V, VCC = 3.6V VIN = 0V, VCC = 3.6V 3 mV mV 10 10 A A www.national.com DS90CR285/DS90CR286 Absolute Maximum Ratings (Note 1) DS90CR285/DS90CR286 Electrical Characteristics (Continued) Over recommended operating supply and temperature ranges unless otherwise specified Symbol Parameter Conditions Min Typ Max Units TRANSMITTER SUPPLY CURRENT ICCTW Transmitter Supply Current Worst Case (with Loads) Transmitter Supply Current Power Down ICCTZ RL = 100, CL = 5 pF, Worst Case Pattern (Figures 1, 2) , TA = -10C to +70C f = 32.5 MHz 31 45 mA f = 37.5 MHz 32 50 mA f = 66 MHz 37 55 mA RL = 100, CL = 5 pF, Worst Case Pattern (Figures 1, 2) , TA = -40C to +85C f = 40 MHz 38 51 mA f = 66 MHz 42 55 mA 10 55 A PWR DWN = Low Driver Outputs in TRI-STATE under Powerdown Mode RECEIVER SUPPLY CURRENT Receiver Supply Current Worst Case ICCRW ICCRZ Receiver Supply Current Power Down CL = 8 pF, Worst Case Pattern (Figures 1, 3) , TA = -10C to +70C f = 32.5 MHz 49 65 mA f = 37.5 MHz 53 70 mA f = 66 MHz 78 105 mA CL = 8 pF, Worst Case Pattern (Figures 1, 3) , TA = -40C to +85C f = 40 MHz 55 82 mA f = 66 MHz 78 105 mA PWR DWN = Low Receiver Outputs Stay Low during Powerdown Mode 10 55 A Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The tables of "Electrical Characteristics" specify conditions for device operation. Note 2: Typical values are given for VCC = 3.3V and TA = +25C. Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise specified (except VOD and VOD). Note 4: VOS previously referred as VCM. Transmitter Switching Characteristics Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol Parameter Min Typ Max Units LLHT LVDS Low-to-High Transition Time (Figure 2) 0.5 1.5 ns LHLT LVDS High-to-Low Transition Time (Figure 2) 0.5 1.5 ns TCIT TxCLK IN Transition Time (Figure 4) 5 ns TCCS TxOUT Channel-to-Channel Skew (Figure 5) TPPos0 Transmitter Output Pulse Position for Bit0 (Note 7) (Figure 16) TPPos1 TPPos2 250 -0.4 0 0.4 ns Transmitter Output Pulse Position for Bit1 3.1 3.3 4.0 ns Transmitter Output Pulse Position for Bit2 6.5 6.8 7.6 ns www.national.com f = 40 MHz ps 4 (Continued) Over recommended operating supply and -40C to +85C ranges unless otherwise specified Min Typ Max Units TPPos3 Symbol Transmitter Output Pulse Position for Bit3 Parameter 10.2 10.4 11.0 ns TPPos4 Transmitter Output Pulse Position for Bit4 13.7 13.9 14.6 ns TPPos5 Transmitter Output Pulse Position for Bit5 17.3 17.6 18.2 ns TPPos6 Transmitter Output Pulse Position for Bit6 TPPos0 Transmitter Output Pulse Position for Bit0 (Note 6) (Figure 16) TPPos1 21.0 21.2 21.8 ns -0.4 0 0.3 ns Transmitter Output Pulse Position for Bit1 1.8 2.2 2.5 ns TPPos2 Transmitter Output Pulse Position for Bit2 4.0 4.4 4.7 ns TPPos3 Transmitter Output Pulse Position for Bit3 6.2 6.6 6.9 ns TPPos4 Transmitter Output Pulse Position for Bit4 8.4 8.8 9.1 ns TPPos5 Transmitter Output Pulse Position for Bit5 10.6 11.0 11.3 ns TPPos6 Transmitter Output Pulse Position for Bit6 12.8 13.2 13.5 ns TCIP TxCLK IN Period (Figure 6 ) 15 T 50 ns TCIH TxCLK IN High Time (Figure 6) 0.35T 0.5T 0.65T ns TCIL TxCLK IN Low Time (Figure 6) 0.35T 0.5T 0.65T ns TSTC TxIN Setup to TxCLK IN (Figure 6) 2.5 ns THTC TxIN Hold to TxCLK IN (Figure 6) 0 ns TCCD TxCLK IN to TxCLK OUT Delay @ 25C,VCC=3.3V (Figure 3 f = 66 MHz 3.7 5.5 ns 8) TPLLS Transmitter Phase Lock Loop Set (Figure 10) 10 ms TPDD Transmitter Powerdown Delay (Figure 14) 100 ns Receiver Switching Characteristics Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol Parameter Min Typ Max Units 2.2 5.0 ns ns CLHT CMOS/TTL Low-to-High Transition Time (Figure 3) CHLT CMOS/TTL High-to-Low Transition Time (Figure 3) RSPos0 Receiver Input Strobe Position for Bit 0 (Note 7)(Figure 17) RSPos1 Receiver Input Strobe Position for Bit 1 RSPos2 Receiver Input Strobe Position for Bit 2 8.1 8.5 9.15 ns RSPos3 Receiver Input Strobe Position for Bit 3 11.6 11.9 12.6 ns RSPos4 Receiver Input Strobe Position for Bit 4 15.1 15.6 16.3 ns RSPos5 Receiver Input Strobe Position for Bit 5 18.8 19.2 19.9 ns RSPos6 Receiver Input Strobe Position for Bit 6 22.5 22.9 23.6 ns RSPos0 Receiver Input Strobe Position for Bit 0 (Note 6)(Figure 17) 0.7 1.1 1.4 ns RSPos1 Receiver Input Strobe Position for Bit 1 2.9 3.3 3.6 ns RSPos2 Receiver Input Strobe Position for Bit 2 5.1 5.5 5.8 ns RSPos3 Receiver Input Strobe Position for Bit 3 7.3 7.7 8.0 ns RSPos4 Receiver Input Strobe Position for Bit 4 9.5 9.9 10.2 ns RSPos5 Receiver Input Strobe Position for Bit 5 11.7 12.1 12.4 ns RSPos6 Receiver Input Strobe Position for Bit 6 13.9 14.3 14.6 ns RSKM RxIN Skew Margin (Note 5) (Figure 18) RCOP RxCLK OUT Period (Figure 7) RCOH RxCLK OUT High Time (Figure 7) RCOL RxCLK OUT Low Time (Figure 7) 5 f = 40 MHz f = 66 MHz 2.2 5.0 1.0 1.4 2.15 ns 4.5 5.0 5.8 ns f = 40 MHz 490 ps f = 66 MHz 400 ps 15 T f = 40 MHz 6.0 10.0 ns f = 66 MHz 4.0 6.1 ns f = 40 MHz 10.0 13.0 ns f = 66 MHz 6.0 7.8 ns 50 ns www.national.com DS90CR285/DS90CR286 Transmitter Switching Characteristics DS90CR285/DS90CR286 Receiver Switching Characteristics (Continued) Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol RSRC Parameter RxOUT Setup to RxCLK OUT (Figure 7) RHRC RxOUT Hold to RxCLK OUT (Figure 7) RCCD RxCLK IN to RxCLK OUT Delay (Figure 9) Min Typ f = 40 MHz 6.5 14.0 Max Units f = 66 MHz 2.5 8.0 ns f = 40 MHz 6.0 8.0 ns f = 66 MHz 2.5 4.0 f = 40 MHz 4.0 6.7 8.0 ns f = 66 MHz 5.0 6.6 9.0 ns ns ns RPLLS Receiver Phase Lock Loop Set (Figure 11) 10 ms RPDD Receiver Powerdown Delay (Figure 15) 1 s Note 5: Receiver Skew Margin is defined as the valid data sampling region at the receiver inputs. This margin takes into account the transmitter pulse positions (min and max) and the receiver input setup and hold time (internal data sampling window). This margin allows LVDS interconnect skew, inter-symbol interference (both dependent on type/length of cable), and clock jitter less than 250 ps). Note 6: The min. and max. limits are based on the worst bit by applying a -400ps/+300ps shift from ideal position. Note 7: The min. and max. are based on the actual bit position of each of the 7 bits within the LVDS data stream across PVT. AC Timing Diagrams 01291002 FIGURE 1. "Worst Case" Test Pattern 01291003 01291004 FIGURE 2. DS90CR285 (Transmitter) LVDS Output Load and Transition Times www.national.com 6 DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291005 01291006 FIGURE 3. DS90CR286 (Receiver) CMOS/TTL Output Load and Transition Times 01291007 FIGURE 4. DS90CR285 (Transmitter) Input Clock Transition Time 01291008 Note 8: Measurements at VDIFF = 0V Note 9: TCCS measured between earliest and latest LVDS edges. Note 10: TxCLK Differential LowHigh Edge FIGURE 5. DS90CR285 (Transmitter) Channel-to-Channel Skew 7 www.national.com DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291009 FIGURE 6. DS90CR285 (Transmitter) Setup/Hold and High/Low Times 01291010 FIGURE 7. DS90CR286 (Receiver) Setup/Hold and High/Low Times 01291011 FIGURE 8. DS90CR285 (Transmitter) Clock In to Clock Out Delay 01291012 FIGURE 9. DS90CR286 (Receiver) Clock In to Clock Out Delay www.national.com 8 DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291013 FIGURE 10. DS90CR285 (Transmitter) Phase Lock Loop Set Time 01291014 FIGURE 11. DS90CR286 (Receiver) Phase Lock Loop Set Time 01291015 FIGURE 12. Seven Bits of LVDS in Once Clock Cycle 9 www.national.com DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291016 FIGURE 13. 28 ParalIeI TTL Data Inputs Mapped to LVDS Outputs 01291017 FIGURE 14. Transmitter Powerdown DeIay 01291018 FIGURE 15. Receiver Powerdown Delay www.national.com 10 DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291019 FIGURE 16. Transmitter LVDS Output Pulse Position Measurement 11 www.national.com DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291028 FIGURE 17. Receiver LVDS Input Strobe Position www.national.com 12 DS90CR285/DS90CR286 AC Timing Diagrams (Continued) 01291020 C -- Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max Tppos -- Transmitter output pulse position (min and max) RSKM Cable Skew (type, length) + Source Clock Jitter (cycle to cycle)(Note 11) + ISI (Inter-symbol interference)(Note 12) Cable Skew -- typically 10 ps-40 ps per foot, media dependent Note 11: Cycle-to-cycle jitter is less than 250 ps Note 12: ISI is dependent on interconnect length; may be zero FIGURE 18. Receiver LVDS Input Skew Margin Pin Descriptions DS90CR285 MTD56 (TSSOP) Package Pin Description -- Channel Link Transmitter I/O No. TxIN Pin Name I 28 TTL level input. Description TxOUT+ O 4 Positive LVDS differential data output. TxOUT- O 4 Negative LVDS differential data output. TxCLK IN I 1 TTL IeveI clock input. The rising edge acts as data strobe. Pin name TxCLK IN. TxCLK OUT+ O 1 Positive LVDS differential clock output. TxCLK OUT- O 1 Negative LVDS differential clock output. PWR DWN I 1 TTL level input. Assertion (low input) TRI-STATES the outputs, ensuring low current at power down. VCC I 4 Power supply pins for TTL inputs. GND I 5 Ground pins for TTL inputs. PLL VCC I 1 Power supply pin for PLL. PLL GND I 2 Ground pins for PLL. LVDS VCC I 1 Power supply pin for LVDS outputs. LVDS GND I 3 Ground pins for LVDS outputs. DS90CR286 MTD56 (TSSOP) Package Pin Description -- Channel Link Receiver I/O No. RxIN+ Pin Name I 4 Positive LVDS differential data inputs. Description RxIN- I 4 Negative LVDS differential data inputs. RxOUT O 28 TTL level data outputs. RxCLK IN+ I 1 Positive LVDS differential clock input. RxCLK IN- I 1 Negative LVDS differential clock input. RxCLK OUT O 1 TTL level clock output. The rising edge acts as data strobe. Pin name RxCLK OUT. PWR DWN I 1 TTL level input.When asserted (low input) the receiver outputs are low. VCC I 4 Power supply pins for TTL outputs. GND I 5 Ground pins for TTL outputs. PLL VCC I 1 Power supply for PLL. 13 www.national.com DS90CR285/DS90CR286 DS90CR286 MTD56 (TSSOP) Package Pin Description -- Channel Link Receiver (Continued) I/O No. PLL GND Pin Name I 2 Ground pin for PLL. Description LVDS VCC I 1 Power supply pin for LVDS inputs. LVDS GND I 3 Ground pins for LVDS inputs. using Twin-Coax cable. Twin-Coax has very low cable skew and EMI due to its construction and double shielding. All of the design considerations discussed here and listed in the supplemental application notes provide the subsystem communications designer with many useful guidelines. It is recommended that the designer assess the tradeoffs of each application thoroughly to arrive at a reliable and economical cable solution. BOARD LAYOUT: To obtain the maximum benefit from the noise and EMI reductions of LVDS, attention should be paid to the layout of differential lines. Lines of a differential pair should always be adjacent to eliminate noise interference from other signals and take full advantage of the noise canceling of the differential signals. The board designer should also try to maintain equal length on signal traces for a given differential pair. As with any high speed design, the impedance discontinuities should be limited (reduce the numbers of vias and no 90 degree angles on traces). Any discontinuities which do occur on one signal line should be mirrored in the other line of the differential pair. Care should be taken to ensure that the differential trace impedance match the differential impedance of the selected physical media (this impedance should also match the value of the termination resistor that is connected across the differential pair at the receiver's input). Finally, the location of the CHANNEL LINK TxOUT/RxIN pins should be as close as possible to the board edge so as to eliminate excessive pcb runs. All of these considerations will limit reflections and crosstalk which adversely effect high frequency performance and EMI. Applications Information The Channel Link devices are intended to be used in a wide variety of data transmission applications. Depending upon the application the interconnecting media may vary. For example, for lower data rate (clock rate) and shorter cable lengths ( < 2m), the media electrical performance is less critical. For higher speed/long distance applications the media's performance becomes more critical. Certain cable constructions provide tighter skew (matched electrical length between the conductors and pairs). Twin-coax for example, has been demonstrated at distances as great as 5 meters and with the maximum data transfer of 1.848 Gbit/s. Additional applications information can be found in the following National Interface Application Notes: AN = #### Topic AN-1041 Introduction to Channel Link AN-1108 Channel Link PCB and Interconnect Design-In Guidelines AN-806 Transmission Line Theory AN-905 Transmission Line Calculations and Differential Impedance AN-916 Cable Information CABLES: A cable interface between the transmitter and receiver needs to support the differential LVDS pairs. The 21-bit CHANNEL LINK chipset (DS90CR215/216) requires four pairs of signal wires and the 28-bit CHANNEL LINK chipset (DS90CR285/286) requires five pairs of signal wires. The ideal cable/connector interface would have a constant 100 differential impedance throughout the path. It is also recommended that cable skew remain below 150 ps ( @ 66 MHz clock rate) to maintain a sufficient data sampling window at the receiver. In addition to the four or five cable pairs that carry data and clock, it is recommended to provide at least one additional conductor (or pair) which connects ground between the transmitter and receiver. This low impedance ground provides a common mode return path for the two devices. Some of the more commonly used cable types for point-to-point applications include flat ribbon, flex, twisted pair and TwinCoax. All are available in a variety of configurations and options. Flat ribbon cable, flex and twisted pair generally perform well in short point-to-point applications while TwinCoax is good for short and long applications. When using ribbon cable, it is recommended to place a ground line between each differential pair to act as a barrier to noise coupling between adjacent pairs. For Twin-Coax cable applications, it is recommended to utilize a shield on each cable pair. All extended point-to-point applications should also employ an overall shield surrounding all cable pairs regardless of the cable type. This overall shield results in improved transmission parameters such as faster attainable speeds, longer distances between transmitter and receiver and reduced problems associated with EMS or EMI. The high-speed transport of LVDS signals has been demonstrated on several types of cables with excellent results. However, the best overall performance has been seen when www.national.com UNUSED INPUTS: All unused inputs at the TxIN inputs of the transmitter must be tied to ground. All unused outputs at the RxOUT outputs of the receiver must then be left floating. INPUTS: The TxIN and control inputs are compatible with LVCMOS and LVTTL levels. These pins are not 5V tolerant. TERMINATION: Use of current mode drivers requires a terminating resistor across the receiver inputs. The CHANNEL LINK chipset will normally require a single 100 resistor between the true and complement lines on each differential pair of the receiver input. The actual value of the termination resistor should be selected to match the differential mode characteristic impedance (90 to 120 typical) of the cable. Figure 19 shows an example. No additional pull-up or pulldown resistors are necessary as with some other differential technologies such as PECL. Surface mount resistors are recommended to avoid the additional inductance that accompanies leaded resistors. These resistors should be placed as close as possible to the receiver input pins to reduce stubs and effectively terminate the differential lines. DECOUPLING CAPACITORS: Bypassing capacitors are needed to reduce the impact of switching noise which could limit performance. For a conservative approach three parallel-connected decoupling capacitors (Multi-Layered Ceramic type in surface mount form factor) between each VCC and the ground plane(s) are recommended. The three capacitor values are 0.1 F, 0.01F and 0.001 F. An example is shown in Figure 20. The designer should employ wide traces for power and ground and ensure each capacitor has its own via to the ground plane. If board space is limiting the 14 the most filtering/bypassing. Next would be the LVDS VCC pins and finally the logic VCC pins. (Continued) number of bypass capacitors, the PLL VCC should receive 01291024 FIGURE 19. LVDS Serialized Link Termination for channel-to-channel skew and interconnect skew as a part of the overall jitter/skew budget. COMMON MODE vs. DIFFERENTIAL MODE NOISE MARGIN: The typical signal swing for LVDS is 300 mV centered at +1.2V. The CHANNEL LINK receiver supports a 100 mV threshold therefore providing approximately 200 mV of differential noise margin. Common mode protection is of more importance to the system's operation due to the differential data transmission. LVDS supports an input voltage range of Ground to +2.4V. This allows for a 1.0V shifting of the center point due to ground potential differences and common mode noise. POWER SEQUENCING AND POWERDOWN MODE: Outputs of the CNANNEL LINK transmitter remain in TRISTATE (R) until the power supply reaches 2V. Clock and data outputs will begin to toggle 10 ms after VCC has reached 3V and the Powerdown pin is above 1.5V. Either device may be placed into a powerdown mode at any time by asserting the Powerdown pin (active low). Total power dissipation for each device will decrease to 5 W (typical). The CHANNEL LINK chipset is designed to protect itself from accidental loss of power to either the transmitter or receiver. If power to the transmit board is lost, the receiver clocks (input and output) stop. The data outputs (RxOUT) retain the states they were in when the clocks stopped. When the receiver board loses power, the receiver inputs are shorted to V CC through an internal diode. Current is limited (5 mA per input) by the fixed current mode drivers, thus avoiding the potential for latchup when powering the device. 01291025 FIGURE 20. CHANNEL LINK Decoupling Configuration CLOCK JITTER: The CHANNEL LINK devices employ a PLL to generate and recover the clock transmitted across the LVDS interface. The width of each bit in the serialized LVDS data stream is one-seventh the clock period. For example, a 66 MHz clock has a period of 15 ns which results in a data bit width of 2.16 ns. Differential skew (t within one differential pair), interconnect skew (t of one differential pair to another) and clock jitter will all reduce the available window for sampling the LVDS serial data streams. Care must be taken to ensure that the clock input to the transmitter be a clean low noise signal. Individual bypassing of each VCC to ground will minimize the noise passed on to the PLL, thus creating a low jitter LVDS clock. These measures provide more margin 15 www.national.com DS90CR285/DS90CR286 Applications Information DS90CR285/DS90CR286 Applications Information (Continued) 01291026 FIGURE 21. Single-Ended and Differential Waveforms www.national.com 16 inches (millimeters) Order Number DS90CR285MTD or DS90CR286MTD NS Package Number MTD56 LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. DS90CR285/DS90CR286 +3.3V Rising Edge Data Strobe LVDS 28-Bit Channel Link-66 MHz Physical Dimensions unless otherwise noted IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated