DSG3000 Series RF Signal Generator Highest frequency: 3GHz/6GHz Amplitude accuracy: <0.5dB (typical) Output amplitude range: -130 dBm to +13 dBm High signal purity, phase noise: <-110dBc/Hz@20kHz (typical) Standard 0.5ppm internal clock; 5ppb high stable clock for option Standard AM/FM/M analog modulation Standard pulse modulation; on/off ratio up to 80dB; pulse train generator for option I/Q modulation and I/Q baseband output All modulations support internal and external modulation modes Standard 2U height design to save rack space; rack mount kit is available Standard USB/LAN/GPIB remote control interfaces; support SCPI command set Wear-free electronic attenuator design Well-designed automatic flatness calibration function (Cables, attenuators, amplifiers and so on) for test system with power meter control RIGOL TECHNOLOGIES,INC. DSG3000 Series RF Signal Generator Menu keys Preset/View/Help Main function keys Flexible and easy-to-use editing keyboard 4.3 inches TFT LCD Signal output switches Power key with delay switching design RF signal output System function Manual trigger LF signal output External modulation input Standard GPIB/USB/LAN interfaces Support USB storage device, power meter sensor or power meter with USB interface High stable OCXO reference clock (option) 10 MHz reference clock IN/OUT Trigger in/signal valid output/sweep progress output designed for system integration I/Q modulating signal input and baseband signal output Pulse modulation input, pulse gated signal input, pulse signal generator output Dimensions: W x H x D = 364 mm x 112 mm x 420 mm; Weight: 6.4kg (without packag) Main Functions 9kHz~3/6GHz +25dBm~-140dBm Frequency sweep, Amplitude sweep, Frequency and amplitude sweep RIGOL 1 CW Sweep LF PMC Sine, Square, Triangle, Ramp, Swp-Sine Power meter controller, Test system automatic calibration Internal modulation, External modulation Internal modulation, External modulation, Pulse train generator, Pulse generator AM Pulse FM M I/Q Internal modulation, External modulation Internal modulation, External modulation, I/Q baseband generator, Baseband output Specifications Specifications are valid under the following conditions: the instrument in the calibration cycle is stored at least two hours at 0C to 50C temperature, and 40 minutes warm up. The specifications include measurement uncertainty. Data represented in this manual are specifications unless otherwise noted. Typical (typ.): describes characteristic performance, which 80 percent of the measurement results will meet at room temperature (approximately 25 C). This data is not warranted, does not include measurement uncertainty. Nominal (nom.): indicates the expected mean or average performance, or an attribute whose performance is by design, such as the 50 connector. This data is not warranted and is measured at room temperature (approximately 25 C). Measured (meas.): describes an attribute measured during the design phase for purposes of communicating expected performance, such as amplitude drift vs. time. This data is not warranted and is measured at room temperature (approximately 25 C). NOTE: All charts represented in this manual are the measurement results of multiple instruments at room temperature unless otherwise noted. Frequency Frequency 9kHz to 3GHz 9kHz to 6GHz Frequency resolution Setting time Phase offset DSG3030 DSG3060 0.01Hz <10ms[1] (typ.) Adjustable in 0.01 steps (nom.) Frequency Band[2] Band 1 2 3 Frequency f 23.4375MHz 23.4375MHz < f 46.875MHz 46.875MHz < f 93.75MHz N 1 0.03125 0.0625 4 5 6 7 8 9 93.75MHz < f 187.5MHz 187.5MHz < f 375MHz 375MHz < f 750MHz 750MHz < f 1500MHz 1500MHz < f 3000MHz 3000MHz < f 6000MHz 0.125 0.25 0.5 1 2 4 Frequency range Internal Reference Frequency Reference frequency Temperature stability Aging rate Output for internal reference frequency Input for external reference frequency 10MHz In temperature range 0 to 50 , reference to 25 With OCXO-A08 option With OCXO-A08 option Frequency Level Output impedance Frequency Level Maximum deviation Input impedance < 0.5ppm < 5ppb < 1ppm/year < 30ppb/year 10MHz +8dBm (typ.) 50 (nom.) 10MHz 0dBm to +10dBm 5ppm 50 (nom.) Frequency Sweep Operating mode Sweep mode Sweep range Sweep shape Step change Number of points Dwell time range Triggering Step sweep (equally or logarithmically spaced frequency steps) List sweep (the list of arbitrary frequency steps) Single, continuous Full frequency range Triangle, ramp Linear or logarithmic Step sweep 2 to 65535 List sweep 1 to 6001 20ms to 100s Auto, trigger key, external, bus (GPIB, USB, LAN) NOTE: [1] Except in the case of the band1 is switched with another band. [2] N is a factor used to help define certain specifications within the document. RIGOL 2 Spectral Purity[1] Harmonic CW mode, 1MHz f 6GHz, level +13dBm <-30dBc CW mode f 3GHz <-65dBc, <-80dBc (typ.) 3GHz < f 6GHz <-52dBc, <-70dBc (typ.) CW mode, level > -10dBm, carrier offset > 10kHz f 1.5GHz <-64dBc, <-70dBc (typ.) 1.5GHz < f 3GHz <-58dBc, <-64dBc (typ.) 3GHz < f 6GHz <-52dBc, <-58dBc (typ.) CW mode, at 20kHz carrier offset, 1Hz measurement bandwidth f = 100MHz <-120dBc/Hz f = 1GHz <-108dBc/Hz, <-110dBc/Hz (typ.) f = 3GHz <-102dBc/Hz, <-104dBc/Hz (typ.) f = 6GHz <-96dBc/Hz, <-98dBc/Hz (typ.) CW mode, RMS value at f = 1GHz 0.3kHz to 3kHz <5Hz rms, <1Hz rms (typ.) 0.03kHz to 20kHz <30Hz rms, <8Hz rms (typ.) Sub harmonic Non harmonic SSB phase noise Residual FM Measured +13dBm output, Harmonics VS frequency Harmonics(dBc) Harmonics(dBc) Carrier frequency(MHz) SSB phase noise (dBc/Hz) Measured SSB phase noise Carrier offset NOTE: [1] Without IQ-DSG3000 option. RIGOL 3 Measured 0dBm output, Harmonics VS frequency Carrier frequency(MHz) Level Setting Range Specification level range +7dBm +13dBm +13dBm +13dBm -110dBm -130dBm 9kHz f <100kHz 100kHz f <1MHz 1MHz f 3GHz 3GHz <f 6GHz 9kHz f <100kHz 100kHz f 6GHz 0.01dB Maximum output level Minimum output level Setting resolution Minimum output level VS frequency Setting range +10dBm +15dBm +25dBm +20dBm -120dBm -140dBm Minimum output level (dBm) Maximum output level (dBm) Maximum output level VS frequency Frequency(MHz) Frequency(MHz) Measured maximum output level VS frequency Level (dB) Minimum output level (dBm) Measured level repeatability at 6GHz 0dBm, ALC ON, 25 Time (hours) Frequency(MHz) Absolute Level Uncertainty[1] 9kHz f <100kHz Level uncertainty 100kHz f 3GHz 3GHz < f 6GHz VSWR [2] 1MHz f 6GHz +13 to -60dBm 0.5dB (typ.) 0.7dB, 0.5 (typ.) 0.9dB, 0.5 (typ.) <1.8 (typ.) -60 to -110dBm 0.7dB (typ.) 0.9dB, 0.5 (typ.) 1.1dB, 0.5 (typ.) -110 to -130dBm 0.7dB (typ.) 0.9dB (typ.) NOTE: [1] ALC state: on or auto mode, 20 to 30 [2] In 50 system, typical, level -10dBm, ATT auto mode RIGOL 4 Measured -60dBm output level VS frequency Measured -110dBm output level VS frequency Level uncertainty (dB) Carrier frequency(MHz) Level uncertainty (dB) Carrier frequency(MHz) Measured -127dBm output level VS frequency Measured -136dBm output level VS frequency Level uncertainty (dB) Carrier frequency(MHz) Level uncertainty (dB) Carrier frequency(MHz) Carrier frequency(MHz) RIGOL 5 Measured 0dBm output level VS frequency Level uncertainty (dB) Level uncertainty (dB) Measured +13dBm output level VS frequency Carrier frequency(MHz) Level Setting Setting time Uninterrupted level setting range ALC state on, frequency fixed, temperature range: 20 to 30 ATT fixed mode, ALC state on, level range -110dBm to +13dBm 5ms (typ.) >20dB (typ.) Max. Reverse Power Max. reverse Power Max. DC voltage 1MHz < f 6GHz 50V 10W Level Sweep Operating mode Sweep mode Sweep range Sweep shape Step change Number of points Dwell time range Triggering Step sweep (equally spaced level steps) List sweep (the list of arbitrary level steps) Single, continuous Full level range Triangle, ramp Linear Step sweep List sweep 20ms to 100s Auto, trigger key, external, bus(GPIB, USB, LAN) 2 to 65535 1 to 6001 Internal Modulation Generator (LF) Internal Modulation Generator (LF) Waveform Frequency range Resolution Frequency error Output voltage[1] Output impedance Sine sweep Sine, square, triangle, ramp, sine sweep Sine, sine sweep Square Triangle, ramp 0.01Hz Same as RF reference source Setting range Resolution 50 (nom.) Sweep mode Sweep range Sweep time Sweep shape 0.1Hz to 1MHz 0.1Hz to 20kHz 0.1Hz to 100kHz 1mV to 3V 1mV Single, continuous Frequency range of LF output 1ms to 1000s Triangle, ramp Auto, trigger key, external, bus (GPIB, USB, LAN) Triggering Modulation[2] Simultaneous Modulation AM FM OM Pulse mod. I/Q mod.(option) AM x FM x OM x Pulse mod. I/Q mod. (option) x - NOTE: :compatible; x: incompatible; :compatible with AM performance reduced Amplitude Modulation Modulation source Modulation depth[3] Resolution Modulation accuracy AM distortion Modulation frequency response Sensitivity when using external input Internal, external, internal + external 0% to 100% 0.1% fmod = 1kHz fmod = 1kHz, m 30%, level = 0dBm m 80%, 10Hz to 50kHz fmod = 1kHz <4% of setting+1% <3% (typ.) <3dB (nom.) 1Vpp for indicated depth[4] (nom.) NOTE: [1] Measurement in high-impedance state. [2] The modulation source is sine waveform unless otherwise noted. [3]Peak power of the envelope is no more than the maximum value of the specification output range. [4] To ensure the modulation performance, the input amplitude of the external modulating signal should be less than 0.5V. RIGOL 6 Frequency Modulation Modulation source Maximum deviation Resolution Modulation accuracy FM distortion Modulation frequency response[5] Sensitivity when using external input Phase Modulation Modulation source Maximum deviation Resolution Modulation accuracy OM distortion Modulation frequency response[6] Sensitivity when using external input Pulse Modulation Modulation source On/off ratio Rise/fall time (10%/90%) Pulse repetition frequency Pulse Generator Operating mode Pulse period Pulse width Trigger delay Double-pulse spacing Triggering Internal, external, internal + external N x 1MHz (nom.) < 0.1% of deviation, or 1Hz, which ever is greater (nom.) fmod = 1kHz, internal mode <2% of setting + 20Hz fmod = 1kHz, deviation = N x 50kHz <2% (typ.) 10Hz to 100kHz <3dB (nom.) fmod = 1kHz 1Vpp for indicated deviation[4] (nom.) Internal, external, internal + external f 23.4375MHz 3rad (nom.) f > 23.4375MHz N x 5rad (nom.) < 0.1% of deviation, or 0.01rad, which ever is greater (nom.) fmod = 1kHz, internal modulation source < 1% of setting + 0.1rad fmod = 1kHz, deviation = 5rad < 1% (typ.) 10Hz to 100kHz < 3dB (nom.) fmod = 1kHz 1Vpp for indicated deviation[4] (nom.) External, internal 25MHz f < 3GHz 3GHz f 6GHz <50ns[7], 10ns (typ.) DC to 1MHz >80dB >70dB Single pulse, double pulse, pulse train(option PUG-DSG3000) Setting range 40ns to 170s Resolution 10ns Setting range 10ns to (170s-10ns) Resolution 10ns Setting range 10ns to 170s Resolution 10ns Setting range 20ns to (170s-20ns) Resolution 10ns Auto, external trigger, external gate, trigger key, bus (GPIB, USB, LAN) Pulse Train Generator (Option PUG-DSG3000) Number of pulse patterns Pulse train generator On/off time range Repetition per pattern 1 to 2047 20ns to 170s 1 to 256 Pulse Generator Setting single double train NOTE: [5] External operating mode, measured at 100kHz deviation. [6] External operating mode, measured at 5rad deviation. [7] The state of ALC is off. RIGOL 7 trigger I/Q Modulation (Option IQ-DSG3000) Modulation source Bandwidth.(RF) Carrier suppression[1] Suppression of image sideband[2] External I/Q input External, internal External modulation Baseband (I or Q) RF (I + Q) Internal modulation Baseband (I or Q) RF (I + Q) Carrier frequency range:50MHz f 6GHz Modulation bandwidth up to 10MHz VSWR 120MHz (nom.) 240MHz (nom.) 30MHz (nom.) 60MHz (nom.) 40dBc (typ.) 40dBc (typ.) <1.5 Full scale input I 2 + Q 2 = 0.5Vrms Internal modulation EVM External modulation EVM ACPR 16QAM , root cosine filter ( = 0.22), 4MSps 50MHz f 3GHz (level 4dBm) 3GHz < f 6GHz (level 0dBm) QPSK , root cosine filter ( = 0.22), 4MSps 50MHz f 3GHz (level 4dBm) 3GHz < f 6GHz (level 0dBm) 0.7%rms (typ.) 1.2%rms (typ.) 0.7%rms (typ.) 1.2%rms (typ.) CDMA2000/1xEV-D0,1.2288 Mcps, frequency 800 to 900MHz, 1800 to 1900MHz, level4dBm Measured internal IQ bandwidth dB dB Measured external IQ bandwidth 1.2%, 0.8% (typ.) 70dB Frequency offset from carrier (MHz) Measured carrier suppression Measured suppression of image sideband Carrier suppression (dBc) Suppression of image sideband (dBc) Frequency offset from carrier (MHz) Carrier frequency (MHz) Carrier frequency (MHz) NOTE: [1] [2]The parameter is measured at room temperature. When the temperature is difference from room temperature, the specification will deteriorate. RIGOL 8 I/Q Baseband Generator (Option IQ-DSG3000) Output impedance 50 (nom.) Setting range Output voltage Resolution Frequency response Referenced to 1MHz Magnitude I/Q imbalance Nonlinear phase SFDR Sine Waveform length Waveform memory Sample rate Resolution Loading time 1Msample Nonvolatile memory Setting range Resolution Triggering Trigger Operating modes External trigger delay Setting range Resolution External trigger inhibit Setting range Resolution External trigger pulse width 10MHz 30MHz 10MHz 30MHz 10MHz 30MHz 30MHz 0.1Vpp to 1.5Vpp 1mV <0.5dB (nom.) <1dB (nom.) <0.1dB (nom.) <0.2dB (nom.) 200ps (nom.) 500ps (nom.) >50dB (nom.) 1 sample to 16 Msample in one-sample steps 14 bits <10 s[1] (nom.) 1G Bytes 1 kHz to 50 MHz,100 MHz 0.01 Hz Auto, trigger key, external, bus(GPIB, USB, LAN) Retrig, armed auto, armed retrig, single 0 to (216 - 1) 1 0 to (216 - 1) 1 >20 ns (nom.) Input and Output Front Panel Connector RF output External modulation signal input Internal modulation generator.(LF) output Impedance Connector Impedance Connector Impedance Connector 50 (nom.) N female 100k (nom.) BNC female 50 (nom.) BNC female Impedance Connector Trigger voltage Connector Output voltage Connector Output voltage Impedance Input/output voltage Impedance Connector Impedance Connector Impedance Connector 1k (nom.) BNC female 5V TTL level BNC female 0V/3.3V (nom.) BNC female 0 to 10V (nom.) 50 (nom.) 0V/3.3V (nom.) 50 (nom.) BNC female 50 (nom.) BNC female 50 (nom.) BNC female Connector Protocol Connector Protocol LXI Core 2011 Device A plug Version2.0 B plug Version2.0 10/100Base, RJ-45 IEEE488.2 Rear Panel Connector External trigger in Signal valid output Sweep out Pulse input or output 10MHz in (external frequency reference input) 10MHz out (external frequency reference output) I/Q baseband input/output (option IQDSG3000) Rear Panel Communication Interface USB host USB device LAN IEC/IEEE bus (GPIB) NOTE: [1] Load from flash internal non-volatile memory. RIGOL 9 General Specifications Display Type Resolution Size TFT LCD 480*272 4.3" Mass Memory Mass memory Data storage space Flash non-volatile memory (internal); USB disk (not supplied) Flash non-volatile memory (internal) 1G Bytes Electromagnetic Compatibility and Safety In line with EMC instruction (2014/30/EU), In line with or exceed IEC61326-1:2013/EN61326-1:2013 Group 1 Class A standard CISPR 11/EN 55011 IEC 61000-4-2:2008/EN 61000-4-2 4.0kV (contact discharge), 4.0kV (air discharge) IEC 61000-4-3:2002/EN 61000-4-3 3V/m (80MHz to 1GHz) 3V/m (1.4GHz to 2GHz) 1V/m (2.0GHz to 2.7GHz) IEC 61000-4-4:2004/EN 61000-4-4 1kV power lines IEC 61000-4-5:2001/EN 61000-4-5 0.5kV (phase to Neutral) 1kV (phase to PE) 1kV (neutral to PE) IEC 61000-4-6:2003/EN 61000-4-6 3V, 0.15-80MHz IEC 61000-4-11:2004/EN 61000-4-11 Voltage dip: 0% UT during half cycle 0% UT during 1 cycle 70% UT during 25 cycles Short interruption: 0% UT during 250 cycles EMC Safety In line with IEC 61010-1:2010 (Third Edition)/EN 61010-1:2010, UL 61010-1:2012 R4.16 and CAN/CSA-C22.2 NO. 61010-1-12+ GI1+ GI2 Environmental Altitude Operating temperature range Storage temperature range 0 to 30 30 to 40 Operating height Dimensions (W x H x D) 364 mm x 112 mm x 420 mm (14.33 in x 4.41 in x 16.54 in) Temperature Humidity 0 to 50 -20 to 70 95% rel. humidity 75% rel. humidity Up to 3,048m (10000ft) Weight With IQ-DSG3000 option 6.4kg (14.1Ib) 6.7kg (14.8Ib) Calibration Interval Recommended calibration interval 18 months RIGOL 10 Ordering Information Model Standard accessories Options Description Order Number Signal Generator, 9kHz to 3GHz DSG3030 Signal Generator, 9kHz to 6GHz DSG3060 Quick Guide (Hard Copy) - Power Cable - Pulse Train Generator PUG-DSG3000 High Stable OCXO Reference Clock OCXO-A08 I/Q Modulation, Baseband Output IQ-DSG3000 Rack Mount Kit RM-DSG3000 Power Meter Controller PMC-DSG3000 Include: N(F)-N(F) adaptor (1pcs), N(M)-N(M) adaptor (1pcs), N(M)-SMA(F) adaptor (2pcs), N(M)-BNC(F) adaptor (2pcs), SMA(F)-SMA(F) adaptor (1pcs), SMA(M)-SMA(M) adaptor RF Adaptor Kit (1pcs), BNC T type adaptor (1pcs), 50 SMA load (1pcs), 50 BNC impedance adaptor (1pcs) Optional accessories Include: 50 to 75 adaptor (2pcs) RF CATV Kit Include: 6dB attenuator (1pcs), 10dB attenuator (2pcs) RF Attenuator Kit N(M)-N(M) RF cable CB-NM-NM-75-L-12G N(M)-SMA(M) RF cable CB-NM-SMAM-75-L-12G RF demo kit (receiver) RX1000 NOTE: All instruments, accessories and options can be ordered from your local RIGOL distributors. Warranty Three -year warranty, excluding probes and accessories. HEADQUARTER EUROPE NORTH AMERICA JAPAN RIGOL TECHNOLOGIES, INC. No.156,Cai He Village, Sha He Town, Chang Ping District, Beijing, 102206 P.R.China Tel:+86-10-80706688 Fax:+86-10-80720067 Electronic Measurement Instrument service and support email:EMD_support@rigol.com RIGOL TECHNOLOGIES EU GmbH Lindbergh str. 4 82178 Puchheim Germany Tel: 0049- 89/89418950 Email: info-europe@rigol.com RIGOL TECHNOLOGIES, USA INC. 8140 SW Nimbus Ave. Beaverton, OR 97008 Tel: 877-4-RIGOL-1 Email: info@rigol.com RIGOL TECHNOLOGIES JAPAN, LLC MJ BLDG.3F,1-7-4 MINATO,CHUOUKU,TOKYO,JAPAN 104-0043 Tel: 03-6262-8932 Fax: 03-6262-8933 Email: info-japan@rigol.com RIGOL(R) is the registered trademark of RIGOL Technologies, Inc. Product information in this document subject to update without notice. For the latest information about RIGOL's products, applications and services, please contact local RIGOL office or access RIGOL official website: www.rigol.com July 2017