CB-NM-SMAM-75-L-12G - RIGOL TECHNOLOGIES

RF Signal Generator

Series

DSG3000

Highest frequency: 3GHz/6GHz

Amplitude accuracy: <0.5dB (typical)

Output amplitude range: -130 dBm to +13 dBm

High signal purity, phase noise: <-110dBc/Hz@20kHz (typical)

Standard 0.5ppm internal clock; 5ppb high stable clock for option

Standard AM/FM/ΦM analog modulation

Standard pulse modulation; on/off ratio up to 80dB;

pulse train generator for option

I/Q modulation and I/Q baseband output

All modulations support internal and external modulation modes

Standard 2U height design to save rack space;

rack mount kit is available

Standard USB/LAN/GPIB remote control interfaces;

support SCPI command set

Wear-free electronic attenuator design

Well-designed automatic atness calibration function

(Cables, attenuators, ampliers and so on) for test

system with power meter control

RIGOL TECHNOLOGIES,INC.

RIGOL 1

ΦM

DSG3000 Series RF Signal Generator

Dimensions: W × H × D = 364 mm × 112 mm × 420 mm; Weight: 6.4kg (without packag)

9kHz~3/6GHz

+25dBm~-140dBm

Sine, Square,

Triangle, Ramp,

Swp-Sine

Frequency sweep,

Amplitude sweep,

Frequency and

amplitude sweep

Internal modulation,

External modulation

Internal modulation,

External modulation,

I/Q baseband generator,

Baseband output

Internal modulation,

External modulation,

Pulse train generator,

Pulse generator

Internal modulation,

External modulation

Power meter controller,

Test system automatic

calibration

Standard GPIB/USB/LAN interfaces

10 MHz reference clock IN/OUT

I/Q modulating signal input and baseband signal output

Pulse modulation input, pulse gated signal input,

pulse signal generator output

Trigger in/signal valid output/sweep progress

output designed for system integration

High stable OCXO reference clock (option)

Support USB storage device, power

meter sensor or power meter with

USB interface

CW AM

I/Q

PMC

Sweep

Sweep Pulse

Pulse

Main Functions

Preset/View/Help

Signal output

switches

Power key with delay

switching design

RF signal output

Main function keys

Flexible and easy-to-use editing keyboard

4.3 inches TFT LCD

Menu keys

System function

Manual trigger

LF signal output

External modulation input

RIGOL 2

Specications

Frequency

Specifications are valid under the following conditions: the instrument in the calibration cycle is stored at least two hours at 0°C to 50°C

temperature, and 40 minutes warm up. The specications include measurement uncertainty. Data represented in this manual are specications

unless otherwise noted.

Typical (typ.): describes characteristic performance, which 80 percent of the measurement results will meet at room temperature

(approximately 25 °C). This data is not warranted, does not include measurement uncertainty.

Nominal (nom.): indicates the expected mean or average performance, or an attribute whose performance is by design,

such as the 50Ω connector. This data is not warranted and is measured at room temperature (approximately 25 °C).

Measured (meas.): describes an attribute measured during the design phase for purposes of communicating expected performance,

such as amplitude drift vs. time. This data is not warranted and is measured at room temperature (approximately 25 °C).

NOTE: All charts represented in this manual are the measurement results of multiple instruments at room temperature unless otherwise noted.

Frequency

Frequency range DSG3030 9kHz to 3GHz

DSG3060 9kHz to 6GHz

Frequency resolution 0.01Hz

Setting time <10ms[1] (typ.)

Phase offset Adjustable in 0.01° steps (nom.)

Frequency Band[2]

Band Frequency N

1f ≤ 23.4375MHz 1

223.4375MHz < f ≤46.875MHz 0.03125

346.875MHz < f ≤ 93.75MHz 0.0625

493.75MHz < f ≤ 187.5MHz 0.125

5187.5MHz < f ≤ 375MHz 0.25

6375MHz < f ≤ 750MHz 0.5

7 750MHz < f ≤ 1500MHz 1

81500MHz < f ≤ 3000MHz 2

93000MHz < f ≤ 6000MHz 4

Internal Reference Frequency

Reference frequency 10MHz

Temperature stability In temperature range 0℃ to 50℃, reference to 25℃< 0.5ppm

With OCXO-A08 option < 5ppb

Aging rate < 1ppm/year

With OCXO-A08 option < 30ppb/year

Output for internal reference

frequency

Frequency 10MHz

Level +8dBm (typ.)

Output impedance 50Ω (nom.)

Input for external reference frequency

Frequency 10MHz

Level 0dBm to +10dBm

Maximum deviation ±5ppm

Input impedance 50Ω (nom.)

NOTE: [1] Except in the case of the band1 is switched with another band.

[2] N is a factor used to help dene certain specications within the document.

Frequency Sweep

Operating mode Step sweep (equally or logarithmically spaced frequency steps)

List sweep (the list of arbitrary frequency steps)

Sweep mode Single, continuous

Sweep range Full frequency range

Sweep shape Triangle, ramp

Step change Linear or logarithmic

Number of points Step sweep 2 to 65535

List sweep 1 to 6001

Dwell time range 20ms to 100s

Triggering Auto, trigger key, external, bus (GPIB, USB, LAN)

RIGOL 3

NOTE: [1] Without IQ-DSG3000 option.

Spectral Purity[1]

Harmonic CW mode, 1MHz ≤ f ≤ 6GHz, level ≤ +13dBm <-30dBc

Sub harmonic

CW mode

f ≤ 3GHz <-65dBc, <-80dBc (typ.)

3GHz < f ≤ 6GHz <-52dBc, <-70dBc (typ.)

Non harmonic

CW mode, level > -10dBm, carrier offset > 10kHz

f ≤ 1.5GHz <-64dBc, <-70dBc (typ.)

1.5GHz < f ≤ 3GHz <-58dBc, <-64dBc (typ.)

3GHz < f ≤ 6GHz <-52dBc, <-58dBc (typ.)

SSB phase noise

CW mode, at 20kHz carrier offset, 1Hz measurement bandwidth

f = 100MHz <-120dBc/Hz

f = 1GHz <-108dBc/Hz, <-110dBc/Hz (typ.)

f = 3GHz <-102dBc/Hz, <-104dBc/Hz (typ.)

f = 6GHz <-96dBc/Hz, <-98dBc/Hz (typ.)

Residual FM

CW mode, RMS value at f = 1GHz

0.3kHz to 3kHz <5Hz rms, <1Hz rms (typ.)

0.03kHz to 20kHz <30Hz rms, <8Hz rms (typ.)

Carrier frequency(MHz)

Measured +13dBm output, Harmonics VS frequency

Harmonics(dBc)

Carrier frequency(MHz)

Measured 0dBm output, Harmonics VS frequency

Harmonics(dBc)

SSB phase noise (dBc/Hz)

Carrier offset

Measured SSB phase noise

RIGOL 4

Level

Setting Range

Specication level range Setting range

Maximum output level

9kHz ≤ f <100kHz +7dBm +10dBm

100kHz ≤ f <1MHz +13dBm +15dBm

1MHz ≤f ≤3GHz +13dBm +25dBm

3GHz <f ≤6GHz +13dBm +20dBm

Minimum output level 9kHz ≤ f <100kHz -110dBm -120dBm

100kHz ≤ f ≤ 6GHz -130dBm -140dBm

Setting resolution 0.01dB

Frequency(MHz)

Minimum output level VS frequency

Minimum output level (dBm)

Maximum output level VS frequency

Frequency(MHz)

Maximum output level (dBm)

Measured maximum output level VS frequency

Frequency(MHz)

Minimum output level (dBm)

Absolute Level Uncertainty[1]

Level uncertainty

+13 to -60dBm -60 to -110dBm -110 to -130dBm

9kHz ≤ f <100kHz ≤ 0.5dB (typ.) ≤ 0.7dB (typ.)

100kHz ≤ f ≤3GHz ≤ 0.7dB,

≤0.5 (typ.)

≤0.9dB,

≤0.5 (typ.) ≤0.7dB (typ.)

3GHz < f ≤6GHz ≤ 0.9dB,

≤0.5 (typ.)

≤1.1dB,

≤0.5 (typ.) ≤0.9dB (typ.)

VSWR[2] 1MHz ≤ f ≤6GHz <1.8 (typ.)

Time (hours)

Measured level repeatability at 6GHz 0dBm, ALC ON, 25℃

Level (dB)

NOTE: [1] ALC state: on or auto mode, 20℃ to 30℃

[2] In 50Ω system, typical, level ≤-10dBm, ATT auto mode

RIGOL 5

Carrier frequency(MHz)

Carrier frequency(MHz) Carrier frequency(MHz)

Carrier frequency(MHz)

Measured +13dBm output level VS frequency

Measured -60dBm output level VS frequency Measured -110dBm output level VS frequency

Measured 0dBm output level VS frequency

Level uncertainty (dB)

Level uncertainty (dB) Level uncertainty (dB)

Level uncertainty (dB)

Carrier frequency(MHz) Carrier frequency(MHz)

Measured -127dBm output level VS frequency Measured -136dBm output level VS frequency

Level uncertainty (dB)

RIGOL 6

Level Setting

Setting time ALC state on, frequency xed,

temperature range: 20℃ to 30℃≤ 5ms (typ.)

Uninterrupted level setting range ATT xed mode, ALC state on, level range -110dBm to

+13dBm >20dB (typ.)

Max. Reverse Power

Max. reverse Power Max. DC voltage 50V

1MHz < f ≤ 6GHz 10W

Level Sweep

Operating mode Step sweep (equally spaced level steps)

List sweep (the list of arbitrary level steps)

Sweep mode Single, continuous

Sweep range Full level range

Sweep shape Triangle, ramp

Step change Linear

Number of points Step sweep 2 to 65535

List sweep 1 to 6001

Dwell time range 20ms to 100s

Triggering Auto, trigger key, external, bus(GPIB, USB, LAN)

Internal Modulation Generator (LF)

Waveform Sine, square, triangle, ramp, sine sweep

Frequency range

Sine, sine sweep 0.1Hz to 1MHz

Square 0.1Hz to 20kHz

Triangle, ramp 0.1Hz to 100kHz

Resolution 0.01Hz

Frequency error Same as RF reference source

Output voltage[1] Setting range

Resolution 1mV

Output impedance 50Ω (nom.)

Sine sweep

Sweep mode Single, continuous

Sweep range Frequency range of LF output

Sweep time 1ms to 1000s

Sweep shape Triangle, ramp

Triggering Auto, trigger key, external, bus (GPIB,

USB, LAN)

1mV to 3V

Internal Modulation Generator (LF)

Modulation[2]

Simultaneous Modulation

AM FM ØM Pulse mod. I/Q mod. (option)

AM - ○ ○ △ ×

FM ○ - × ○ ○

ØM ○ × - ○ ○

Pulse mod. △ ○ ○ - ○

I/Q mod.(option) × ○ ○ ○ -

NOTE: ○:compatible; ×: incompatible; △:compatible with AM performance reduced

Amplitude Modulation

Modulation source Internal, external, internal + external

Modulation depth[3] 0% to 100%

Resolution 0.1%

Modulation accuracy fmod = 1kHz <4% of setting+1%

AM distortion fmod = 1kHz, m ≤ 30%, level = 0dBm <3% (typ.)

Modulation frequency response m ≤ 80%, 10Hz to 50kHz <3dB (nom.)

Sensitivity when using external input fmod = 1kHz 1Vpp for indicated depth[4] (nom.)

NOTE: [1] Measurement in high-impedance state.

[2] The modulation source is sine waveform unless otherwise noted.

[3]Peak power of the envelope is no more than the maximum value of the specication output range.

[4] To ensure the modulation performance, the input amplitude of the external modulating signal should be less than ±0.5V.

RIGOL 7

NOTE: [5] External operating mode, measured at 100kHz deviation.

[6] External operating mode, measured at 5rad deviation.

[7] The state of ALC is off.

Pulse Generator Setting

single

double

train

trigger

Frequency Modulation

Modulation source Internal, external, internal + external

Maximum deviation N × 1MHz (nom.)

Resolution < 0.1% of deviation, or 1Hz, which ever is greater (nom.)

Modulation accuracy fmod = 1kHz, internal mode <2% of setting + 20Hz

FM distortion fmod = 1kHz, deviation = N × 50kHz <2% (typ.)

Modulation frequency response[5] 10Hz to 100kHz <3dB (nom.)

Sensitivity when using external input fmod = 1kHz 1Vpp for indicated deviation[4] (nom.)

Phase Modulation

Modulation source Internal, external, internal + external

Maximum deviation f ≤ 23.4375MHz 3rad (nom.)

f > 23.4375MHz N × 5rad (nom.)

Resolution < 0.1% of deviation, or 0.01rad, which ever is greater (nom.)

Modulation accuracy fmod = 1kHz, internal modulation source < 1% of setting + 0.1rad

ØM distortion fmod = 1kHz, deviation = 5rad < 1% (typ.)

Modulation frequency response[6] 10Hz to 100kHz < 3dB (nom.)

Sensitivity when using external input fmod = 1kHz 1Vpp for indicated deviation[4] (nom.)

Pulse Modulation

Modulation source External, internal

On/off ratio 25MHz ≤ f < 3GHz

3GHz ≤ f ≤ 6GHz

Rise/fall time (10%/90%) <50ns[7], 10ns (typ.)

Pulse repetition frequency DC to 1MHz

Pulse Generator

Operating mode Single pulse, double pulse, pulse train(option PUG-DSG3000)

Pulse period Setting range 40ns to 170s

Resolution 10ns

Pulse width Setting range 10ns to (170s-10ns)

Resolution 10ns

Trigger delay Setting range 10ns to 170s

Resolution 10ns

Double-pulse spacing Setting range 20ns to (170s-20ns)

Resolution 10ns

Triggering Auto, external trigger, external gate, trigger key, bus (GPIB, USB, LAN)

Pulse Train Generator (Option PUG-DSG3000)

Pulse train generator

Number of pulse patterns 1 to 2047

On/off time range 20ns to 170s

Repetition per pattern 1 to 256

>80dB

>70dB

RIGOL 8

I/Q Modulation (Option IQ-DSG3000)

Modulation source External, internal

Bandwidth.(RF)

External modulation

Baseband (I or Q) ≤120MHz (nom.)

RF (I + Q) ≤240MHz (nom.)

Internal modulation

Baseband (I or Q) ≤30MHz (nom.)

RF (I + Q) ≤60MHz (nom.)

Carrier suppression[1] Carrier frequency range:50MHz ≤ f ≤ 6GHz ≥40dBc (typ.)

Suppression of image sideband[2] Modulation bandwidth up to ±10MHz ≥40dBc (typ.)

External I/Q input VSWR <1.5

Full scale input

Internal modulation

EVM

16QAM , root cosine lter (α = 0.22), 4MSps

50MHz ≤ f ≤ 3GHz (level ≤ 4dBm) ≤ 0.7%rms (typ.)

3GHz < f ≤ 6GHz (level ≤ 0dBm) ≤ 1.2%rms (typ.)

QPSK , root cosine lter (α = 0.22), 4MSps

50MHz ≤ f ≤ 3GHz (level ≤ 4dBm) ≤ 0.7%rms (typ.)

3GHz < f ≤ 6GHz (level ≤ 0dBm) ≤ 1.2%rms (typ.)

External modulation

EVM CDMA2000/1xEV-D0,1.2288 Mcps, frequency 800 to

900MHz, 1800 to 1900MHz, level≤4dBm

≤ 1.2%, ≤ 0.8% (typ.)

ACPR ≥ 70dB

VrmsQI 5.0

NOTE: [1] [2]The parameter is measured at room temperature. When the temperature is difference from room temperature, the specication will deteriorate.

Frequency offset from carrier (MHz) Frequency offset from carrier (MHz)

Carrier frequency (MHz) Carrier frequency (MHz)

Carrier suppression (dBc)

Suppression of image sideband (dBc)

Measured external IQ bandwidth

Measured suppression of image sideband

Measured carrier suppression

Measured internal IQ bandwidth

RIGOL 9

Input and Output

I/Q Baseband Generator (Option IQ-DSG3000)

Output impedance 50Ω (nom.)

Output voltage Setting range 0.1Vpp to 1.5Vpp

Resolution 1mV

Frequency response Referenced to 1MHz

I/Q imbalance

Magnitude

Nonlinear phase

SFDR Sine

Waveform memory

Waveform length 1 sample to 16 Msample

in one-sample steps

Resolution 14 bits

Loading time 1Msample <10 s[1] (nom.)

Nonvolatile memory 1G Bytes

Sample rate Setting range 1 kHz to 50 MHz,100 MHz

Resolution 0.01 Hz

Trigger

Triggering Auto, trigger key, external, bus(GPIB,

USB, LAN)

Operating modes Retrig, armed auto, armed retrig, single

External trigger delay

Setting range 0 to (216 - 1)

Resolution 1

External trigger inhibit

Setting range 0 to (216 - 1)

Resolution 1

External trigger pulse width >20 ns (nom.)

Front Panel Connector

RF output Impedance 50Ω (nom.)

Connector N female

External modulation signal input Impedance 100kΩ (nom.)

Connector BNC female

Internal modulation generator.(LF)

output

Impedance 50Ω (nom.)

Connector BNC female

Rear Panel Connector

External trigger in

Impedance 1kΩ (nom.)

Connector BNC female

Trigger voltage 5V TTL level

Signal valid output Connector BNC female

Output voltage 0V/3.3V (nom.)

Sweep out Connector BNC female

Output voltage 0 to 10V (nom.)

Pulse input or output Impedance 50Ω (nom.)

Input/output voltage 0V/3.3V (nom.)

10MHz in (external frequency

reference input)

Impedance 50Ω (nom.)

Connector BNC female

10MHz out (external frequency

reference output)

Impedance 50Ω (nom.)

Connector BNC female

I/Q baseband input/output (option IQ-

DSG3000)

Impedance 50Ω (nom.)

Connector BNC female

Rear Panel Communication Interface

USB host Connector A plug

Protocol Version2.0

USB device Connector B plug

Protocol Version2.0

LAN LXI Core 2011 Device 10/100Base, RJ-45

IEC/IEEE bus (GPIB) IEEE488.2

NOTE: [1] Load from ash internal non-volatile memory.

≤ 10MHz <0.5dB (nom.)

≤ 30MHz <1dB (nom.)

≤ 10MHz <0.1dB (nom.)

≤ 30MHz <0.2dB (nom.)

≤ 10MHz 200ps (nom.)

≤ 30MHz 500ps (nom.)

≤ 30MHz >50dB (nom.)

RIGOL 10

General Specications

Display

Type TFT LCD

Resolution 480*272

Size 4.3”

Mass Memory

Mass memory Flash non-volatile memory (internal); USB disk (not supplied)

Data storage space Flash non-volatile memory (internal) 1G Bytes

Environmental

Temperature Operating temperature range 0℃ to 50℃

Storage temperature range -20℃ to 70℃

Humidity 0℃ to 30℃ ≤95% rel. humidity

30℃ to 40℃ ≤75% rel. humidity

Altitude Operating height Up to 3,048m (10000ft)

Dimensions

(W × H × D) 364 mm × 112 mm × 420 mm (14.33 in × 4.41 in × 16.54 in)

Weight

6.4kg (14.1Ib)

With IQ-DSG3000 option 6.7kg (14.8Ib)

Electromagnetic Compatibility and Safety

EMC

In line with EMC instruction (2014/30/EU),

In line with or exceed IEC61326-1:2013/EN61326-1:2013 Group 1 Class A standard

CISPR 11/EN 55011

IEC 61000-4-2:2008/EN 61000-4-2 ±4.0kV (contact discharge), ±4.0kV (air discharge)

IEC 61000-4-3:2002/EN 61000-4-3

3V/m (80MHz to 1GHz)

3V/m (1.4GHz to 2GHz)

1V/m (2.0GHz to 2.7GHz)

IEC 61000-4-4:2004/EN 61000-4-4 1kV power lines

IEC 61000-4-5:2001/EN 61000-4-5

0.5kV (phase to Neutral)

1kV (phase to PE)

1kV (neutral to PE)

IEC 61000-4-6:2003/EN 61000-4-6 3V, 0.15-80MHz

IEC 61000-4-11:2004/EN 61000-4-11

Voltage dip:

0% UT during half cycle

0% UT during 1 cycle

70% UT during 25 cycles

Short interruption:

0% UT during 250 cycles

Safety

In line with

IEC 61010-1:2010 (Third Edition)/EN 61010-1:2010,

UL 61010-1:2012 R4.16 and CAN/CSA-C22.2 NO. 61010-1-12+ GI1+ GI2

Calibration Interval

Recommended calibration interval 18 months

Ordering Information

NOTE: All instruments, accessories and options can be ordered from your local RIGOL distributors.

Warranty

Three -year warranty, excluding probes and accessories.

Description Order Number

Model Signal Generator, 9kHz to 3GHz DSG3030

Signal Generator, 9kHz to 6GHz DSG3060

Standard

accessories

Quick Guide (Hard Copy) -

Power Cable -

Options

Pulse Train Generator PUG-DSG3000

High Stable OCXO Reference Clock OCXO-A08

I/Q Modulation, Baseband Output IQ-DSG3000

Rack Mount Kit RM-DSG3000

Power Meter Controller PMC-DSG3000

Optional

accessories

Include: N(F)-N(F) adaptor (1pcs), N(M)-N(M) adaptor (1pcs), N(M)-SMA(F) adaptor (2pcs),

N(M)-BNC(F) adaptor (2pcs), SMA(F)-SMA(F) adaptor (1pcs), SMA(M)-SMA(M) adaptor

(1pcs), BNC T type adaptor (1pcs), 50 Ω SMA load (1pcs), 50 Ω BNC impedance adaptor

(1pcs)

RF Adaptor Kit

Include: 50 Ω to 75 Ω adaptor (2pcs) RF CATV Kit

Include: 6dB attenuator (1pcs), 10dB attenuator (2pcs) RF Attenuator Kit

N(M)-N(M) RF cable CB-NM-NM-75-L-12G

N(M)-SMA(M) RF cable CB-NM-SMAM-75-L-12G

RF demo kit (receiver) RX1000

RIGOL® is the registered trademark of RIGOL Technologies, Inc. Product information in this

document subject to update without notice. For the latest information about RIGOL's products,

applications and services, please contact local RIGOL ofce or access RIGOL ofcial

website: www.rigol.com

July 2017

HEADQUARTER

RIGOL TECHNOLOGIES, INC.

No.156,Cai He Village,

Sha He Town,

Chang Ping District, Beijing,

102206 P.R.China

Tel:+86-10-80706688

Fax:+86-10-80720067

Electronic Measurement

Instrument service and support

email:EMD_support@rigol.com

EUROPE

RIGOL TECHNOLOGIES EU GmbH

Lindbergh str. 4

82178 Puchheim

Germany

Tel: 0049- 89/89418950

Email: info-europe@rigol.com

NORTH AMERICA

RIGOL TECHNOLOGIES, USA INC.

8140 SW Nimbus Ave.

Beaverton, OR 97008

Tel: 877-4-RIGOL-1

Email: info@rigol.com

JAPAN

RIGOL TECHNOLOGIES JAPAN, LLC

MJ BLDG.3F,1-7-4 MINATO,CHUOU-

KU,TOKYO,JAPAN 〒104-0043

Tel: 03-6262-8932

Fax: 03-6262-8933

Email: info-japan@rigol.com