3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Three-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle 3000 Series
Military (with 3M’s 3518 or N3518 polarizing key) •
and center bump polarization
Low profile•
Optional ejector latches•
Mounting holes for securing header to board•
Three wall shroud provides design flexibility•
Solder tail and wrap tail options•
Optional polarizing posts available•
Optional high temperature insulator suitable for “no •
lead” soldering operations
High temperature option is suitable for reflow •
soldering using “paste in hole” techniques
See Regulatory Information Appendix for chemical •
compliance information
Date Modied: May 1, 2008 TS-0771-C
Sheet 1 of 5
Physical
Insulator:
Material: Glass Filled Polyester (PBT)
Glass Filled Polyester (PCT) - High Temp Option
Flammability: UL 94V-0
Color: Gray (PBT), Beige (PCT), Black (PCT)
Contact:
Material: Copper Alloy
Plating:
Underplating: 100 μ” [ 2.54 μm ] Nickel - Overall
Wiping Area: 30 μ” [ 0.76 μm ] Gold
Solder Tails: 200 μ” [ 5.08 μm ] Tin Lead or Matte Tin (See Ordering Information)
Marking: 3M Logo, Part Identification Number and Orientation Triangle
Electrical
Current Rating: 2 A (EIA 364-70)
Insulation Resistance: >1 × 109 Ω at 500 VDC
Withstanding Voltage: 1000 VRMS at Sea Level
Environmental
Temperature Rating: -55°C to +105°C
Process Rating: 260°C (High Temp. PCT insulator) single pass (per J-STD-020C)
PBT gray insulator, maximum insulator temperature 191°C (solder
wave process only)
Moisture Sensitivity Level: 1 (per J-STD-020C) High Temp. (PCT) versions only
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Three-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle 3000 Series
TS-0771-C
Sheet 2 of 5
.25
6.4 .31
7.9
.28
7.1
D
.100
2.54 REF.
B
POSITION #1
.15
3.8
.020
0.51
.100
2.54 REF.
.13
3.3
2X O .100 [2.54]
SEE NOTE #2
.573 ± .010
[ 14.55 ]
-X2XX
Header with
Short Ejector/Latch
for 3M Sockets without
Strain Relief
-X3XX
Header with
Long Ejector/Latch
for 3M Sockets with
Strain Relief
.424 ± .010
[ 10.77 ]
.08
[2.0]
.97 Ref
[24.6]
.37 Ref
[9.4]
.46 Ref
[11.7]
1.07 Ref
[27.2]
.08
[2.0]
F Typ
Section A-A
(Straight)
E ± .010
.30
[7.6]
.24
[6.1]
.025 ± .002 Sq Typ
[ 0.64 ]
C
L
“Y”
.025 ± .002 Sq
Typ
[ 0.64 ]
Position 1
Orientation
Triangle
.21
[5.3]
.24
[6.1]
.30
[7.6]
F Typ
E ± .010
.049
Ref
.100 Ref
[2.54]
2X Ø .100
[2.54]
(See Note 2) A
C
.16
[4.1]
.197
[5.00] .20
[5.1]
Notch C
(See Table 1 & Note 1)
Notch B
(See Table 1)
Notch A
(See Table 1 & Note1)
B
B
Section B-B
.68
[17.3]
.35
[8.9]
.020
[0.51]
A
A
C
L“Y”
(Right Angle)
.12
[3.0]
-X0XX
Header without Latchs
A
.68
[17.3]
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Three-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle 3000 Series
TS-0771-C
Sheet 3 of 5
Table 1
Pin Qty 3M Part
Number
Dimensions Polarizing
Notches
A B C D
10 3793 1.26 (32.1) 1.105 (28.07) 0.865 (21.97) 0.71 (18.0) BC
14 3314 1.46 (37.2) 1.305 (33.15) 1.065 (27.05) 0.91 (23.1) BC
16 3408 1.56 (39.7) 1.405 (35.69) 1.165 (29.59) 1.01 (25.6) ABC
20 3428 1.76 (44.8) 1.605 (40.77) 1.365 (34.67) 1.21 (30.7) ABC
26 3429 2.06 (52.4) 1.905 (48.39) 1.665 (42.29) 1.51 (38.3) ABC
34 3431 2.46 (62.6) 2.305 (58.55) 2.065 (52.45) 1.91 (48.5) ABC
40 3432 2.76 (70.2) 2.605 (66.17) 2.365 (60.07) 2.21 (56.1) ABC
50 3433 3.26 (82.9) 3.105 (78.87) 2.865 (72.77) 2.71 (68.8) ABC
60 3372 3.76 (95.6) 3.605 (91.57) 3.365 (85.47) 3.21 (81.5) ABC
64 3764 3.96 (100.7) 3.805 (96.65) 3.565 (90.55) 3.41 (86.6) ABC
Inch
(mm)
± .005
± .1 ± .01
Tolerance Unless Noted
.0 .00 .000
Inch
[ ] Dimensions for
Reference only
Table 2
3M Part
Number Suffix Contact Tail Dimension E
Pin Cross Section
Dimension G
Dimension F Diagonals Corner Radii
-1XX2
-2XX2
Solder Tail for
.062 (1.57)
Thick PC Board
.112
(2.84)
.0245 ± .0005
(0.622)
.028 ± .001
(0.71)
.0075 Ref
(0.191)
0.035 ± .003
(0.89) (See Note 3)
-1XO3
-2XO3
Solder Tail for
0.94 (2.39) to .125
(3.18) Thick PC
Board
.155
(3.94)
.0245 ± .0005
(0.622)
.028 ± .001
(0.71)
.0075 Ref
(0.191) 0.035 ± .003 (0.89)
Notes:
1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or N3518).
2. Accepts Rear and Front mounting hardware:
Rear Entry: #4-24 thread cutting screw, 3M Part #3341-5, .116 [2.95] dia mounting hole
Front Entry: (Prior to installation of latch on Straight Versions) #2-56 bolt and nut, 3M Part #3341-6,
.106 [2.69] dia mounting hole
3. The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 ± .002.
Kink is located .05” below bottom surface of plastic. External radius of kink toward part centerline
Ø.106
[2.69]
or Ø.116
[2.95]
(See Note 2)
G Dim
Position 1
.100 ± .003
[2.54]
.100 ± .003
[2.54]
.060
[1.52]
.300
[7.62]
Side to Side Stackability
B
Recommended Mounting Hole Pattern
(Straight)
.352
[8.94]
C
L
“Y”
C
L
.41
[10.4]
Max to Edge of PCB
for Daisy Chain
Ø.106
[2.69]
or Ø.116
[2.95]
(See Note 2)
G Dim
.029
[0.74]
.100 ± .003
[2.54]
Position 1
.232
[5.89]
C
Recommended Mounting Hole Pattern
(Right Angle)
.100 ± .003
[2.54]
“Y”
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Three-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle 3000 Series
TS-0771-C
Sheet 4 of 5
Part Customization
This spec sheet details our standard offering.
3M has several capabilities that can provide a part tailored to
your specific needs. Ask your 3M sales representative or
customer service for more details.
Use of snap-in style latch/ejectors in either short (N3XXX
X5XX) or long (N3XXX-X6XX) styles, installed or shipped
separately (the -5 & -6 snap-in latches are dimensional and
functional equivalents to the -2 & -3 roll pin latches) which
are also available separately with roll pins included. Refer to
chart below.
If ordering snap-in or roll pin style latches separately, please use the below chart
Short Latch Long Latch Latch Style Color
Standard Temperature
(PBT)
3505-2 3505-3 Roll Pin Gray
High Temperature
(PCT)
N3505-2 N3505-3 Roll Pin Beige
High Temperature
(PCT)
N3505-2B N3505-3B Roll Pin Black
High Temperature
(PPA)
3505-30 3505-31 Snap-In Gray
High Temperature
(PPA)
N3505-30 N3505-31 Snap-In Beige
High Temperature
(PPA)
N3505-30B N3505-31B Snap-In Black
Selective pin removal (ATA or other compatability)•
Wire wrap tails styles•
Kinked Tail (K2 option) positions:
2500 & 3000 Series Shrouded Header
Total Number
of Pins
Number of
Tails Kinked
Positions
Kinked
10 4 3478
14 4 3411 12
16 4 34 13 14
20 4 34 17 18
24 4 34 21 22
26 4 34 23 24
30 4 5 6 25 26
34 4 7 8 27 28
36 4 7 8 27 28
40 4 7 8 33 34
50 4 7 8 43 44
60 4 11 12 49 50
64 4 11 12 53 54
Kinked Tail Detail:
Kink is located .05” below bottom surface of plastic.
External radius of kink toward part centerline.
Ordering Information
X3XXX - XXXX XX
Blank = Std. Temp Gray (PBT) /(Blank or UB Pltg. Req’d.)
N = High Temp Beige (PCT) /(Blank or UB Pltg. Req’d.)
N = High Temp Black (PCT)/(RB Plating Req’d)
3M Part Number
(See Table 1)
Latch/Ejector System
0 = No Latch/Ejector
2 = Short Roll PinLatch/Ejectors
3 = Long Roll Pin Latch/Ejectors
Shroud and Pin Conguration
1 = 3 Wall, Right Angle Solder Tail
2 = 3 Wall, Straight Solder Tail
Tail
02 = Solder Tail for .062 [1.57] Thick Board
K2= Kinked Solder Tails for .062 [1.57] Thick Board
03 = Solder Tails for .094 to .125 [2.39 to 3.18] Thick Board
blank or UB = 30 μ” Gold with Sn/Pb Tails (App. E3 & C2 Apply)
RB = 30 μ” Gold with Matte Tin Tails (App. E1 & C1 Apply)
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Three-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle 3000 Series
TS-0771-C
Sheet 5 of 5
.321
[8.15]
.100 Dia
[2.54]
Polarizing Post
Note: Insert Post into one mounting hardware hole on
bottom of header. Set post to protrude .115” [2.92]
3201 -3 P B T G ra y
3201 -4 L C P B la c k
Polarizing Keys
.15
[3.8]
.09
[2.3]
A
Breakaway Tab .34 Ref
[8.6]
Note: #2216 B/A Scotchweld can be used to adhere keys.
Dim A
N3518 LCP Black .02
3518 PBT Gray .02
Mounting Hardware
.31
[7.9]
.50
[12.7]
Panhead Thread Cutting Screw:
#4-24 X 5/16”
Type: USA Std BT, Federal BG
Hex Head Bolt, Nut and Washer
Bolt - #2-56 X 1/2”
3341-5
(Installed from bottom of board)
3341-6
(Must be inserted prior to latch on
vertical headers)
3341-5 & 6
Material - Stainless Steel
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/717/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.
RIA-2217A-D
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means
that the product or part does not contain any of the following substances in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217A-D
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty
period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where
prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the
legal theory asserted.
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217A-D
3M Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects 3M is a trademark of 3M Company.
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls
or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.