R F C o m p o n e n t s July 2013 Balun Transformers Wound SMD ATB series ATB3225-75011CT (3.2u2.5u2.3mm) ATB3225-75032CT (3.2u2.5u2.3mm) ATB3225-75034CT (3.2u2.5u2.3mm) (2/11) R F C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (3/11) R F C o m p o n e n t s Balun Transformers Halogen-free Compatible with lead-free solders Wound SMD Overview of the ATB Series FEATURES The ATB3225 case size is L3.2xW2.5xH2.3mm. The case size is smaller than conventional baluns. The frequency band width for ATB3225-75011CT is 5 to 200MHz, for ATB3225-75032CT is 5 to 100MHz, and for ATB3225-75034CT is 1 to 100MHz. Low insertion loss and good balance parameters. Conforms to the RoHS Directive. APPLICATION Cable modem PART NUMBER CONSTRUCTION ATB Series name 3225 - LxWxH Dimensions (mm) 3.2x2.5x2.3 750 Impedance (:) at 100MHz 750 75 11 CT Impedance ratio Type 11 32 34 1:1 3:2 3:4 CT - Center tap T 000 Packaging style Internal code T TL o180mm reel o330mm reel OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Type Temperature range Operating Storage temperature temperature C C ATB3225-75011CT -25 to +85 -25 to +85 ATB3225-75032CT -25 to +85 -25 to +85 ATB3225-75034CT -25 to +85 -25 to +85 Reel diameter o180mm o330mm o180mm o330mm o180mm o330mm Package quantity Individual weight pieces/reel 2,000 10,000 2,000 10,000 2,000 10,000 mg 75 75 75 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (4/11) R F C o m p o n e n t s Overview of the ATB Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 10 to 30s Peak Temp. T4 245C Time t3 5s max. * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (5/11) R F C o m p o n e n t s ATB series ATB3225-75011CT Type SHAPE & DIMENSIONS 3 4 2 5 1 6 Mark for direction (0.9) 1.8 0.9 2.30.1 2.50.2 3.20.2 0.4 1 6 2 5 3 4 0.18 0.45 0.45 Dimensions in mm RECOMMENDED LAND PATTERN 1.0 2.0 CIRCUIT DIAGRAM Unbalance port Balance port 3 0.55 1 GND or Vcc 0.3 2.25 5 2 6 4 4.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (6/11) R F C o m p o n e n t s ATB series ATB3225-75011CT Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE DC resistance (: )max. Impedance ratio Frequency range (MHz) Insertion loss (dB)max. Return loss (dB)min. 0.7 1:1 (75: :75: ) 5 to 65 5 to 200 0.8 0.5 15 10 Amplitude unbalance (dB)max. 0.1 0.5 Phase unbalance (deg.) 1802 1805 Part No.* ATB3225-75011CT-000 Includes packaging style indication (T: o180mm reel, TL: o330mm reel). Measurement equipment Measurement item Product No. Insertion loss E5071B Return loss E5071B Amplitude unbalance E5071B Phase unbalance E5071B Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies Agilent Technologies FREQUENCY CHARACTERISTICS 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 RETURN LOSS 0 Return loss (dB) Insertion loss (dB) INSERTION LOSS 0 50 100 150 Frequency (MHz) 5 10 15 20 25 200 0 50 100 150 Frequency (MHz) 190 188 186 184 182 180 178 176 174 172 170 Phase unbalance (dB) PHASE UNBALANCE 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 Amplitude unbalance (dB) AMPLITUDE UNBALANCE 0 50 100 150 Frequency (MHz) 200 0 50 100 150 Frequency (MHz) 200 200 * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (7/11) R F C o m p o n e n t s ATB series ATB3225-75032CT Type SHAPE & DIMENSIONS 3 4 2 5 1 6 Mark for direction (0.9) 1.8 0.9 2.30.1 2.50.2 3.20.2 0.4 1 6 2 5 3 4 0.18 0.45 0.45 Dimensions in mm RECOMMENDED LAND PATTERN 1.0 CIRCUIT DIAGRAM Unbalance port 2.0 Balance port 3 0.55 1 GND or Vcc 0.3 2.25 5 2 6 4 4.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (8/11) R F C o m p o n e n t s ATB series ATB3225-75032CT Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE DC resistance (: )max. Impedance ratio Frequency range (MHz) Insertion loss (dB)max. Return loss (dB)min. 0.7 3:2 (75: :50: ) 5 to 100 2 5 Amplitude unbalance (dB)max. 1 Phase unbalance (deg.) 18010 Part No. ATB3225-75032CT-000 Includes packaging style indication (T: o180mm reel, TL: o330mm reel). Measurement equipment Measurement item Product No. Insertion loss E5071B Return loss E5071B Amplitude unbalance E5071B Phase unbalance E5071B Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies Agilent Technologies FREQUENCY CHARACTERISTICS 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 RETURN LOSS 0 Return loss (dB) Insertion loss (dB) INSERTION LOSS 0 50 100 150 Frequency (MHz) 20 30 200 0 50 100 150 Frequency (MHz) 0 50 100 150 Frequency (MHz) 200 PHASE BALANCE Phase balance (dB) Amplitude balance (dB) 15 25 AMPLITUDE BALANCE 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 5 10 200 190 188 186 184 182 180 178 176 174 172 170 0 50 100 150 Frequency (MHz) 200 * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (9/11) R F C o m p o n e n t s ATB series ATB3225-75034CT Type SHAPE & DIMENSIONS 3 4 2 5 1 6 Mark for direction (0.9) 1.8 0.9 2.30.1 2.50.2 3.20.2 0.4 1 6 2 5 3 4 0.18 0.45 0.45 Dimensions in mm RECOMMENDED LAND PATTERN 1.0 2.0 CIRCUIT DIAGRAM Unbalance port Balance port 3 0.55 1 GND or Vcc 0.3 2.25 5 2 6 4 4.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (10/11) R F C o m p o n e n t s ATB series ATB3225-75034CT Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE DC resistance (: )max. Impedance ratio Frequency range (MHz) Insertion loss (dB)max. Return loss (dB)min. 0.7 3:4 (75: :100: ) 1 to 100 2 5 Amplitude unbalance (dB)max. 0.1 Phase unbalance (deg.) 18010 Part No. ATB3225-75034CT-000 Includes packaging style indication (T: o180mm reel, TL: o330mm reel). Measurement equipment Measurement item Product No. Insertion loss E5071B Return loss E5071B Amplitude unbalance E5071B Phase unbalance E5071B Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies Agilent Technologies FREQUENCY CHARACTERISTICS 0 1 2 3 4 5 6 7 8 9 10 RETURN LOSS 0 Return loss (dB) Insertion loss (dB) INSERTION LOSS 15 20 25 1 10 Frequency (MHz) 1 10 Frequency (MHz) 1 10 Frequency (MHz) 100 PHASE BALANCE Phase balance (dB) 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 30 100 AMPLITUDE IMBALANCE Amplitude balance (dB) 5 10 100 185 184 183 182 181 180 179 178 177 176 175 1 10 Frequency (MHz) 100 * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm (11/11) R F C o m p o n e n t s ATB series Packaging style REEL DIMENSIONS 2.00.5 E W1 9+1/-0 9+1/-0 9+1/-0 W2 131 131 131 N 60+1/-0 60+1/-0 60+1/-0 E 2 typ. 2 typ. 2 typ. N Type A ATB3225-75011CT o180+0/-1.5 ATB3225-75032CT o180+0/-1.5 ATB3225-75034CT o180+0/-1.5 1.0 o13.00.2 W1 o21.00.8 W2 A Dimensions in mm TAPE DIMENSIONS P2 P0 W B F E oD0 A K P1 Dimensions in mm Type ATB3225-75011CT ATB3225-75032CT ATB3225-75034CT A 2.90.1 2.90.1 2.90.1 B 3.60.1 3.60.1 3.60.1 oD0 1.5+0.1/0 1.5+0.1/0 1.5+0.1/0 E F 1.750.1 3.50.05 1.750.1 3.50.05 1.750.1 3.50.05 P0 4.00.1 4.00.1 4.00.1 P1 4.00.1 4.00.1 4.00.1 P2 2.00.05 2.00.05 2.00.05 W 8.00.2 8.00.2 8.00.2 K 2.50.05 2.50.05 2.50.05 500 to 560min. 160min. Taping 440min. Drawing direction Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e751_woundbalun_atb3225.fm