M21544, M21554, M21564 3G/HD/SD-SDI Long Reach Adaptive Cable Equalizer with Integrated Jitter Cleaner The M21544/54/64 are multi-rate, highly integrated, adaptive cable equalizers for SDI and DVB-ASI video as well as digital audio applications. It provides adaptive, low noise, high gain equalization for 75 coaxial cable at SDI data rates from 125 Mbps to 2.97 Gbps. The device is capable of compensating for losses accumulated across cable length up to 200 m when operating at 2.97 Gbps. The M21544/54/64 feature an integrated jitter cleaner, which automatically removes the jitter generated at HD-SDI and 3G-SDI at the output of the equalizer, eliminating the need for standalone reclockers at the input and reducing system cost, complexity and power consumption. The jitter cleaner may be powered down and bypassed in applications where it is not required to allow for optimized power consumption for each application. The M21544/54 also feature dual differential outputs, eliminating the need for additional circuitry and simplifying system design. Both outputs feature programmable swing as well as de-emphasis for enabling the signal to be transmitted across 40" of FR4 trace. The second, optional output may be disabled for additional power savings. The M21564 offers a single output solution with a smaller footprint and maximum power savings. The device operates using a single 2.5 V supply voltage and has extremely low power consumption with the equalizer and jitter cleaner dissipating only 145 mW when one output driver is enabled. It may be used in either hardware mode, or controlled through a standard four-wire serial digital interface. Furthermore, it features advanced diagnostic capabilities such as cable length indication, loss of signal detection, and offers power management functions such as power down upon loss of signal. The M21544/54/64 are offered in a green and RoHS compliant small footprint QFN package. Features * SMPTE 424M, SMPTE 292M, SMPTE 344M, SMPTE 259M, and DVB-ASI compliant * Robust adaptive cable equalization for up to 200 meters of Belden 1694A at 2.97 Gbps, up to 200 meters of Belden 1694A at 1.485 Gbps, and up to 400 meters of Belden 1694A at 270 Mbps * Integrated jitter cleaner for 3G/HD-SDI use with automatic rate detection * Individually controllable dual differential output drivers with programmable 8 dB of de-emphasis * Optional 6 dB flatband gain at input * Cable length indication * SD, HD and 3G Data Rate Detection * Optional four-wire serial digital interface * Very low power consumption: 145 mW (single output), 160 mW (dual output) * Power down and mute features * Extended operating temperature range: -40 C to +85 C Applications * Broadcast video routing and production switchers * Broadcast video distribution amplifiers * Broadcast video cameras and monitors Functional Block Diagram LOS Mute SDI 21544-DSH-001-E Prog. 6 dB Gain Adaptive EQ Digital Interface Jitter Cleaner Mindspeed Technologies(R) Mindspeed Proprietary and Confidential DE & Prog. Swing Ctrl SDO0 DE & Prog. Swing Ctrl SDO1 MUX June 2013 Ordering Information Part Number Package Operating Data Rate Operating Temperature M21544G-13* 24-pin QFN (RoHS compliant) 125-2970 Mbps -40 C to 85 C M21554G-13* 32-pin QFN (RoHS compliant) 125-2970 Mbps -40 C to 85 C M21564G-13* 16-pin QFN (RoHS compliant) 125-2970 Mbps -40 C to 85 C * The letter `G' designator after the part number indicates a RoHS-compliant package. Refer to www.mindspeed.com for additional information. Revision History Revision Level Date E Release June 2013 Description Updated ordering information and marking diagram Updated electrical specifications including maximum power consumption and Jitter Performance Chapter 1.0 Added Figure 2-1 and Figure 2-2. Revised xCS pin description for all three devices in Section 3.0. Updated M21544 pins 17, 18 descriptions. D Advance November Updated Ordering information from -11P to -12P Added Marking Diagram Updated typical power consumption Table 1-3 Updated typical electrical specifications Table 1-4 Updated M21554 Pinout, Figure 3-3 Updated M21554 Pin Specifications, Table 3-2 Added 6 dB attenuation in the functional description Section 4.1.3 Updated Digital Interface functional description Section 4.5 Updated 4-Wire specifications Table 4-6 C Advance September 2012 Added Figure 2-1 and Figure 2-2. Revised xCS pin description for all three devices in Section 3.0. Pins 17, 18 revised for M21554. B Advance May 2012 Added electrical specifications, pinout diagram, pin descriptions, package drawings, functional description and register settings. A Advance June 2011 Advance Release. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 2 M21544/54/64 Marking Diagram 13 215X4 XXXX.X YYWW XX 21544-DSH-001-E Part Revision Part Number Lot Number Date Country Code Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 3 1.0 Electrical Characteristics Table 1-1. Absolute Maximum Ratings Symbol AVDD Parameter Minimum Maximum Unit -0.5 2.75 V Analog power supply voltage VIN,PCML DC input voltage (PCML) VSS - 0.5 AVDD + 0.5 V VIN,CMOS DC input voltage (CMOS) VSS - 0.6 DVDD + 0.5 V TSTORE Storage temperature -65 150 C TJUNC Junction temperature -- 125 C VESD,HBM Electrostatic discharge voltage (HBM) -3000 3000 V VESD,CDM Electrostatic discharge voltage (CDM) -500 500 V VESD,mm Electrostatic discharge voltage (mm) -150 150 V NOTES: 1. Exposure of the device beyond the minimum/maximum limits may cause permanent damage. 2. HBM and CDM per JEDEC Class 2 (JESD22-A114-B). 3. Limits listed in the above table are stress limits only and do not imply functional operation within these limits. Table 1-2. Recommended Operating Conditions Symbol Parameter Minimum Typical Maximum Unit VCC Analog power supply voltage 2.37 2.5 2.63 V TCASE Operating case temperature -40 -- 85 C M21544/64 -- -- 13.8 C/W M21554 -- -- 11.5 C/W JC Junction to case thermal resistance NOTES: 1. Thermal resistance value is calculated using a 5% increase on the supply voltage and includes all temperature variations. Table 1-3. Power Consumption Specifications (1 of 2) Symbol ICC Parameter Intermediate output swing (Default) Core Current Consumption Maximum output swing 21544-DSH-001-E Typical Maximum Unit Two outputs enabled 62 75 mA One output enabled 56 68 mA Two outputs enabled 64 78 mA One output enabled 57 70 mA Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 4 Electrical Characteristics Table 1-3. Power Consumption Specifications (2 of 2) Symbol Parameter PTOTAL Intermediate swing (Default) Typical Maximum Unit Two outputs enabled 155 197 mW One output enabled 140 179 mW NOTES: 1. Maximum current and maximum power consumption numbers are calculated using a 5% increase on the supply voltage, with jitter cleaner and include all temperature and process variations. Table 1-4. PCML Input/Output Electrical Characteristics (1 of 2) Symbol Parameter Note Minimum Typical Maximum Unit DR NRZ data rate 125 -- 2970 Mbps VIN Differential input swing 720 800 880 mVPP RIN Input termination resistance -- 2.3 -- CIN Input Capacitance -- 0.4 -- pF S11 Input Return Loss from 5 MHz to 1.5 GHz -- -- -15 dB S11 Input Return Loss from 1.5 GHz to 3 GHz -- -- -10 dB VOUT Differential output swing 1 250 390 540 365 555 740 480 720 940 mVPPD VOCM Output Common Mode Voltage 1 0.8 -- 1.2 V tR/tF Output rise/fall time (20% - 80%) 2 -- 90 130 ps DE Highest output de-emphasis setting 3 0 -- 8 dB 4, 5, 6 -- Jitter Performance tJIT Total jitter added at 2.97 Gbps for the following Belden 1694A cable length 0 - 200 m mUI 100 Total jitter added at 1.485 Gbps for the following Belden 1694A cable length 4, 5, 6 -- 0 - 200 m mUI 50 Total jitter added at 270 Mbps for the following Belden 1694A cable length 4, 5, 6 170 -- 100 -- 0 - 400 m mUI 300 Jitter Cleaner DR DR Input data rate retimed, SMPTE 292M -- 1483, 1485 -- Mbps Input data rate retimed, SMPTE424M -- 2967, 2970 -- Mbps FLBW Loop bandwidth for SMPTE 292M -- 2 -- MHz FLBW Loop bandwidth for SMPTE 424M -- 4 -- MHz 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 5 Electrical Characteristics Table 1-4. PCML Input/Output Electrical Characteristics (2 of 2) Symbol Parameter Note Minimum Typical Maximum Unit tLOCK, ASYNCH Lock time, asynchronous -- -- 15 ms tLOCK, SYNCH Lock time, synchronous -- -- 1 s NOTES: 1. Programmable with 200 mV increments. 2. Measured using a clock pattern with 50% duty cycle and consisting of 10 Consecutive Identical Digits (10 CID) 3. Programmable in 2 dB steps. 4. Measured according to SMPTE RP184 and SMPTE RP192. 5. Jitter cleaner is used for HD and 3G data rates only, bypassed and powered down for SD data rates. 6. Measured to BER 1E-09 using PRBS10 test pattern, using default output swing Table 1-5. Control/Interface Logic Input/Output Characteristics Symbol Parameter Note Minimum Typical Maximum Unit VOH Digital output logic high 1 0.85 x VCC VCC -- V VOL Digital output logic low 2 -- 0 0.15 x VCC V VIH Digital input logic high 0.75 x VCC -- VCC V VIL Digital input logic low 0 -- 0.25 x VCC V VIF Digital input logic float 0.35 x VCC -- 0.65 x VCC V NOTES: 1. IOH = -4 mA. 2. IOL = 4 mA. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 6 2.0 Typical Performance Characteristics Unless otherwise noted, typical performance applies for VCC = 2.5 V, 25 C ambient temperature, 800 mVPP differential input data swing, PRBS 210 - 1 data pattern at 2.97 Gbps. Figure 2-1. 21544-DSH-001-E Eye Diagram @2.97 Gbps, Unequalized Signal, After 200 m Belden 1694A Cable Figure 2-2. Mindspeed Technologies(R) Mindspeed Proprietary and Confidential Eye Diagram @2.97 Gbps, Equalized Signal, After 200 m Belden 1694A Cable (Jitter Cleaner Enabled) 7 3.0 Pinout Diagram, Pin Descriptions, and Package Outline Drawing MF2 V CC MF1 24 23 22 21 20 19 VEE 1 18 SDO1P VEE 2 17 SDO1N SDIP 3 16 VEE 15 SDO0P M21544 4x4 mm 24pin QFN 5 14 SDO0N 6 13 xCS 9 10 Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 11 12 V EE 8 M UTEREF 7 MF0 VEE AGC- 4 AGC+ SDIN MODE_SEL 21544-DSH-001-E M F3 Ground Pad VEE V EE M21544 Pinout Diagram (Bottom View of the Package) V CC Figure 3-1. M21544 Pinout SDO1_DISABLE 3.1 8 Pinout Diagram, Pin Descriptions, and Package Outline Drawing 3.2 M21544 Pin Description Table 3-1. M21544 Pin Descriptions (1 of 2) Pin Name Pin Number(s) Type Description VEE 1,2,5,12,16,23, Ground Pad Ground Negative power supply (ground) VCC 20,24 Power Positive power supply (2.5 V) SDIP/SDIN 3,4 I, SDI Serial data input SDO0P/SDO0N 15,14 O, LVDS Serial data output 0 SDO1P/SDO1N 18,17 O, LVDS Serial data output 1 MODE_SEL 6 I, LVCMOS Mode Select 1: Software Mode Enabled (4-wire digital interface) 0: Hardware Mode Enabled Internal pull down SDO1_DISABLE 7 I, LVCMOS SDO1 disable pin 1: SDO1 disable 0: SDO1 enable Internal pull up. Hardware pin state overrides register setting configurations AGC+/- 8,9 I/O, Analog Equalizer loop filter capacitor (33 nF) MF0 10 I, tri-state LVCMOS Hardware Mode (MODE_SEL =0) BYPASS 1: Bypass entirely the equalizer and jitter cleaner Z: Bypass only the jitter cleaner 0: Normal operation Software Mode (MODE_SEL =1) xSD: Signal Detect Complement 1: No input signal is present or the cable length is above the MUTEREF threshold 0: Input signal is present and cable length is below the MUTEREF threshold MUTEREF 11 I, Analog xCS 13 I, LVCMOS Mute reference input. Defines the cable length threshold at which the signal detect will be asserted. By connecting xSD to MUTE, it controls the maximum cable length after which the part will mute. This pin can be left floating or can be grounded for maximum equalization. Hardware Mode (MODE_SEL =0) Must be set LOW for normal operation. Software Mode (MODE_SEL =1) Chip Select Complement, Internal pullup. MF1 19 I, LVCMOS Hardware Mode (MODE_SEL =0) Automatic sleep control. Sleep mode has precedence over MUTE and BYPASS. 1: Automatic power down when no input is present 0: Normal mode, the equalizer is always active Software Mode (MODE_SEL =1) 4-wire: Signal Out Internal pull up 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 9 Pinout Diagram, Pin Descriptions, and Package Outline Drawing Table 3-1. M21544 Pin Descriptions (2 of 2) Pin Name Pin Number(s) Type MF2 21 I, LVCMOS Description Hardware Mode (MODE_SEL =0) Output mute. MUTE has precedence over BYPASS. 1: Outputs are muted 0: Normal operation Software Mode (MODE_SEL =1) 4-wire: SCLK Internal pull down MF3 22 I, LVCMOS Hardware Mode (MODE_SEL =0) xSD: Signal Detect 1: No input signal is present or the cable length is above the MUTEREF threshold 0: Input signal is present and cable length is below the MUTEREF threshold Software Mode (MODE_SEL =1) 4-wire: Signal In Internal pull down 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 10 Pinout Diagram, Pin Descriptions, and Package Outline Drawing 3.3 M21544 Package Information The M21544 is packaged in a 4 mm footprint, 24-pin QFN. Figure 3-2. 21544-DSH-001-E M21544 Packaging Drawing Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 11 Pinout Diagram, Pin Descriptions, and Package Outline Drawing MF3 MF2 VCC VCC NC 32 31 30 29 28 27 26 25 NC 1 24 MF1 VEE 2 23 SDO1P SDIP 3 22 SDO1N SDIN 4 21 NC 20 SDO0P M21554 5x5 mm 32pin QFN 7 18 xCS 8 17 NC 9 10 11 12 13 14 15 16 NC VEE NC SDO0N MUTEREF 19 NC 6 NC NC MF0 5 AGC- NC MODE_SEL 21544-DSH-001-E VCC Ground Pad VEE NC M21554 Pinout Diagram (Bottom View of the Package) NC Figure 3-3. M21554 Pinout AGC+ 3.4 Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 12 Pinout Diagram, Pin Descriptions, and Package Outline Drawing 3.5 M21554 Pin Description Table 3-2. Pin Name M21554 Pin Descriptions (1 of 2) Pin Number(s) Type Description VEE 2,7, Ground Pad Ground Negative power supply (ground) VCC 26,27,30 Power Positive power supply (2.5 V) SDIP/SDIN 3,4 I, SDI Serial data input SDO0P/SDO0N 20,19 O, LVDS Serial data output 0 SDO1P/SDO1N 23,22 O, LVDS Serial data output 1 MODE_SEL 8 I, LVCMOS Mode Select 1: Software Mode Enabled (4-wire digital interface) 0: Hardware Mode Enabled Internal pull down AGC+/- 9,10 I/O, Analog Equalizer loop filter capacitor (33 nF) MF0 11 I, tri-state LVCMOS Hardware Mode (MODE_SEL =0) BYPASS 1: Bypass entirely the equalizer and jitter cleaner Z: Bypass only the jitter cleaner 0: Normal operation Software Mode (MODE_SEL =1) xSD: Signal Detect Complement 1: No input signal is present or the cable length is above the MUTEREF threshold 0: Input signal is present and cable length is below the MUTEREF threshold MUTEREF 14 I, Analog Mute reference input. Defines the cable length threshold at which signal detect will be asserted. By connecting xSD to MUTE, it controls the maximum cable length after which the part will mute. This pin can be left floating or can be grounded for maximum equalization. xCS 18 I, LVCMOS Hardware Mode (MODE_SEL =0) Must be set LOW for normal operation. Software Mode (MODE_SEL =1) Chip Select Complement, Internal pullup. MF1 24 I, LVCMOS Hardware Mode (MODE_SEL =0) Automatic sleep control. Sleep mode has precedence over MUTE and BYPASS. 1: Automatic power down when no input is present 0: Normal mode, the equalizer is always active Software Mode (MODE_SEL =1) 4-wire: Signal Out Internal pull up 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 13 Pinout Diagram, Pin Descriptions, and Package Outline Drawing Table 3-2. M21554 Pin Descriptions (2 of 2) Pin Name Pin Number(s) Type MF2 28 I, LVCMOS Description Hardware Mode (MODE_SEL =0) Output mute. MUTE has precedence over BYPASS. 1: Outputs are muted 0: Normal operation Software Mode (MODE_SEL =1) 4-wire: SCLK Internal pull down MF3 29 I, LVCMOS Hardware Mode (MODE_SEL =0) xSD: Signal Detect 1: No input signal is present or the cable length is above the MUTEREF threshold 0: Input signal is present and cable length is below the MUTEREF threshold Software Mode (MODE_SEL =1) 4-wire: Signal In Internal pull down NC 1,5,6,12,13, No Connect 15,16,17,21, 25,31,32 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 14 Pinout Diagram, Pin Descriptions, and Package Outline Drawing 3.6 M21554 Package Information The M21554 is packaged in a 5 mm footprint, 32-pin QFN. Figure 3-4. 21544-DSH-001-E M21554 Packaging Drawing Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 15 Pinout Diagram, Pin Descriptions, and Package Outline Drawing VCC Ground Pad VEE MF2 M21564 Pinout Diagram (Bottom View of the Package) MF3 Figure 3-5. M21564 Pinout VCC 3.7 16 15 14 13 VEE 1 12 MF1 SDIP 2 11 SDOP 3 10 SDON 4 9 xCS 21544-DSH-001-E 6 7 Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 8 MUTEREF 5 MF0 MODE_SEL AGC- SDIN AGC+ M21564 4x4 mm 16pin QFN 16 Pinout Diagram, Pin Descriptions, and Package Outline Drawing 3.8 M21564 Pin Description Table 3-3. Pin Name M21564 Pin Descriptions (1 of 2) Pin Number(s) Type Description VEE 1, Ground Pad Ground Negative power supply (ground) VCC 13,16 Power Positive power supply (2.5 V) SDIP/SDIN 2,3 I, SDI Serial data input SDOP/SDON 11,10 O, LVDS MODE_SEL 4 I, LVCMOS Mode Select 1: Software Mode Enabled (4-wire digital interface) 0: Hardware Mode Enabled Internal pull down AGC+/- 5,6 I/O, Analog Equalizer loop filter capacitor (33 nF) MF0 7 I, tri-state LVCMOS Hardware Mode (MODE_SEL =0) BYPASS 1: Bypass entirely the equalizer and jitter cleaner Z: Bypass only the jitter cleaner 0: Normal operation Software Mode (MODE_SEL =1) Signal Detect 1: No input signal is present or the cable length is above the MUTEREF threshold 0: Input signal is present and cable length is below the MUTEREF threshold MUTEREF 8 I, Analog Mute reference input. Defines the cable length threshold at which the signal detect will be asserted. By connecting xSD to MUTE, it controls the maximum cable length after which the part will mute. This pin can be left floating or can be grounded for maximum equalization. xCS 9 I, LVCMOS Serial data output 0 Hardware Mode (MODE_SEL =0) Must be set LOW for normal operation. Software Mode (MODE_SEL =1) Chip Select Complement, Internal pullup. MF1 12 I, LVCMOS Hardware Mode (MODE_SEL =0) Automatic sleep control. Sleep mode has precedence over MUTE and BYPASS. 1: Automatic power down when no input is present 0: Normal mode, the equalizer is always active Software Mode (MODE_SEL =1) 4-wire: Signal Out Internal pull up 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 17 Pinout Diagram, Pin Descriptions, and Package Outline Drawing Table 3-3. M21564 Pin Descriptions (2 of 2) Pin Name Pin Number(s) Type MF2 14 I, LVCMOS Description Hardware Mode (MODE_SEL =0) Output mute. MUTE has precedence over BYPASS. 1: Outputs are muted 0: Normal operation Software Mode (MODE_SEL =1) 4-wire: SCLK Internal pull down MF3 15 I, LVCMOS Hardware Mode (MODE_SEL =0) xSD: Signal Detect 1: No input signal is present or the cable length is above the MUTEREF threshold 0: Input signal is present and cable length is below the MUTEREF threshold Software Mode (MODE_SEL =1) 4-wire: Signal In Internal pull down 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 18 Pinout Diagram, Pin Descriptions, and Package Outline Drawing 3.9 M21564 Package Information The M21564 is packaged in a 4 mm footprint, 16-pin QFN. Figure 3-6. 21544-DSH-001-E M21564 Packaging Drawing Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 19 4.0 Functional Descriptions The M21544/54/64 devices are part of the next generation cable equalizer family for SDI video applications. They allow the transmission of data over of 200 m Belden 1694A cable at 3 Gbps, 220 m at 1.5 Gbps and 400 m at 270 Mbps. The equalizer has an integrated Automatic Rate Detect (ARD) circuitry that allows the jitter cleaner to be enabled for HD and 3G data rates and will be automatically bypassed and turned off for SD rates providing additional power consumption savings. The jitter cleaner can provide retimed one or two serial data outputs with very low alignment jitter. In addition, the jitter cleaner does not need the traditional 27 MHz crystal reference clock. The M21544/54/64 support limited configuration through hardware pin settings (Hardware Mode) or for additional configuration settings, a digital interface is also available (Software Mode). Figure 4-1. M21544/54 Block Diagram M21544/54 Output Buffer0 Programmable Output Swing , Vcm and De -emphasis VCm Input Buffer 5.6nH Adaptive Equalization , 6dB BNC 75 75 1uF 1uF SDO0[P/N] DRV attenuation and signal detection SDIP SDIN Adaptive EQ Jitter Cleaner Output Buffer1 Programmable Output Swing , Vcm and De -emphasis VCm 37.5 DRV MODE_SEL SDO1_DISABLE MF0 MF1 MF2 MF3 21544-DSH-001-E Digital Interface (Hardware or 4-wire mode acess) Mindspeed Technologies(R) Mindspeed Proprietary and Confidential SDO1[P/N] MUTE MUTERef xCS 20 Functional Descriptions Figure 4-2. M21564 Block Diagram M21564 Input Buffer 5.6nH BNC 75 75 Output Buffer0 Adaptive Equalization , 6dB Programmable Output Swing , Vcm attenuation and signal detection 1uF 1uF and De -emphasis VCm SDIP SDIN Adaptive EQ Jitter Cleaner DRV SDO0[P/N] 37.5 MODE_SEL SDO1_DISABLE MF0 MF1 MF2 MF3 4.1 Digital Interface (Hardware or 4-wire mode acess) MUTE MUTERef xCS High-Speed Input Digital video coaxial cables are AC-coupled to the high-speed low-noise inputs (SDIP/SDIN). These are designed to operate in both single-ended or differential mode. The typical application is single-ended into the non-inverting SDI input with the inverting SDI input biased to match the bias on the input used. The M21544/54/64 do not contain any internal input terminations and require both external input termination as well as the matching circuit to exceed the SMPTE input return loss specifications. The package and IC design have been optimized for high-speed performance, allowing them to exceed the SD/HD/3G SMPTE return loss. For non-inverting single-ended operation, the recommended input circuit is shown in Figure 4-1. For differential operation, the matching/termination circuit on SDIP should be duplicated on SDIN. 4.1.1 Input Signal Detection The high-speed input block offers a signal detect function that can be monitored either with pin.MF3 or register.GenConfig bit[7]. The signal detect is also used to turn off the device if there is no signal present at the input. If desired, this function can be bypassed using register.GenConfig bit[4:3] or by setting pin.MF1 = low in hardware mode. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 21 Functional Descriptions 4.1.2 Adaptive Equalizer In typical hardware mode operation, the adaptive equalization is enabled with pin.MF0 = Low (bypass disabled). However, with pin.MF0= High, the adaptive equalization and DC restore circuit are bypassed and the input is fed directly to the output buffers. In software mode operation, the equalizer block can be bypassed by setting register.GenConfig.bit[5] to 1b. The adaptive equalizer can be set to have a 6 dB gain for applications that have 400 mVPP launch amplitude instead of 800 mVPP. To have this 6 dB gain, register 00h bit[2] (register.launch_ctrl) must be set to 1b. Once there is a signal detected at the input of the equalizer, the adaptive equalizer has the ability to report what length of Belden 1694A cable is being used. The cable length indicator results can be read on registers 05h bit[0] and register 06h bit[7:0]. The formulas to calculate the estimated cable length are: CL(m) = 0.625*CLI, for 0-250 m CL(m) = 2.5*(CLI - 400) + 250, for >250 m where CLI is the decimal value of the 9 bits from registers 05h bit[0] (msb) and register 06h bit[7:0] (lsb) and CL is the estimated Belden 1694A cable length in meters. Table 4-1 has some of the decoded values for the cable length indicator registers. Table 4-1. Cable Length Indicator Decoder CLI Results Estimated Cable Length* 000000000 0m 000101000 25 m 001010000 50 m 001111000 75 m 010100000 100 m 011001000 125 m 011110000 150 m 100011000 175 m 101000000 200 m 101101000 225 m 110010000 250 m 110100100 300 m 110111000 350 m 111001100 400 m 111100000 450 m * All cable length indicator values are approximate and are not guaranteed. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 22 Functional Descriptions 4.1.3 6 dB Attenuation The M21544/54/64 provide an option to compensate for 6 dB of flat attenuation in applications where the launch amplitude is a lot lower than 800 mVPPD. When the expected launch amplitude is between ~300 mVPPD and ~500 mVPPD, setting register.GenConfig,bit[2] to 1b will improve the equalizer's performance specially for SD rates. For HD and 3G rates, having the jitter cleaner enabled will result in the best performance in addition to the 6 dB compensation. 4.2 Jitter Cleaner The jitter cleaner on the M21544/54/64 is functional only for HD and 3G video data rates and will be automatically bypassed and turned off for SD rates providing additional power consumption savings. The jitter cleaner features an Automatic Rate Detector (ARD) circuit that monitors the input signal rate and automatically sets the Jitter Cleaner to the correct video rate. The data rate determined by the ARD block may be read from register.JitterCleaner,bit[7:6]. Table 4-2. Jitter Cleaner Data Rate Detector Register.JitterCleaner,bit[7:6] Data Rate Detected 00b SD 01b HD 10b 3G 11b HD or 3G (used when the Jitter cleaner is bypassed) The jitter cleaner is always in auto-bypass mode. If the ARD cannot determine the rate of the input data stream, it will switch the Jitter Cleaner into bypass mode. This allows a data rate other than those specified to be passed through the Jitter Cleaner. 4.3 High-Speed Outputs The high-speed LVDS differential outputs after equalization are made available on the pin.SDO0[P/N] and pin.SDO1[P/N] pins. Note that the M21564 has only one output available, pin.SDO0[P/N]. There are three output swings available - 400 mVPP, 600 mVPP (default) and 800 mVPP. The output swing levels can only be controlled via register.OutputDriver[1:0].bit[7:6]. In addition to controlling the output swing, the common mode voltage (VCM), can also be modified to Auto mode for low common mode DC impedance, 0.8 V, 1.0 V or 1.2 V(default) by programming the desired value to register.OutputDriver[1:0].bit[5:4]. When the output driver is set to have automatic common mode voltage, it will sense the downstream device input common mode and it will match it. Note, the maximum common mode voltage is 1.2 V. In order to improve signal integrity when used in large systems, each output also comes equipped with programmable de-emphasis (DE) for FR4 traces. There are four settings for output de-emphasis: 0 dB (or no DE), 2 dB, 4 dB, and 6 dB. In software mode, the output de-emphasis level for each input may be set by programming the desired value to register.OutputDriver[1:0].bit[3:1]. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 23 Functional Descriptions 4.4 Control Modes The M21544/54/64 may be configured in two separate control modes. The control mode is determined by the setting of the MODE_SEL pin as shown in Table 4-3 below. Table 4-3. Control Mode Setting MODE_SEL Control Mode MODE_SEL = L Hardware Mode MODE_SEL = H Software Mode (4-wire digital interface) 4.4.1 Hardware Mode Configuring the M21544/54/64 in hardware mode avoids the complication of adding a microcontroller, but offers limited control options. When in hardware mode, the MF (Multi Function IO) pins are configured as shown in Table 4-4 below. Table 4-4. MF Pin Configuration in Hardware Mode (MODE_SEL = 0) Pin Name Hardware Mode Pin Name Function MF0 BYPASS EQ and Jitter Cleaner bypass* MF1 AUTOSLEEP Power down EQ when no input signal is present MF2 MUTE Output mute MF3 xSD Signal Detect (Active Low) * Please see pin descriptions for more details. 4.4.2 Software Mode (4-wire Digital Interface Access) In this mode, a four-wire serial interface is used to program the device's internal registers, configuring the operation of the M21544/54/64. When in software mode, MF[3:0] pins comprise the four-wire bus as well as additional diagnostics as shown in Table 4-5 below. Table 4-5. 21544-DSH-001-E MF Pin Configuration in Software mode (4-wire Interface Mode, MODE_SEL = 1) Pin Name 4-Wire Mode Pin Name Function MF0 xSD Signal Detect (Active Low) MF1 S0 Serial Data Output MF2 SCK Serial Data Clock MF3 SI Serial Data Input xCS xCS Chip Select (Active Low) Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 24 Functional Descriptions 4.5 Digital Interface The 4-wire serial interface is selected with pin.MODE_SEL =H. The interface shifts data in from the external controller on the rising edge of the serial clock (SCLK). The serial I/O operation is gated by chip select (xCS). Data is shifted to the M21544/54/64 from the Host (Master) on the serial input (SI) on the falling edge of SCLK, and shifted out through the serial output (SO) on the rising edge of SCLK. To address a register, a 10-bit input needs to be shifted using SI, consisting of the Start Bit (SB) = 1, the Operation bit (OP) = 1 for read, = 0 for write; and the 8-bit address (MSB first). Figure 4-3. 4-wire Serial Digital Interface Figure 4-4 illustrates the Serial Write Mode. To initiate a Write sequence, xCS goes low before the falling edge of SCLK. On each falling edge of the clock, the 18 bits consisting of the Start Bit = 1, OP = 0 for write, ADDR (8-bit), and DATA (8-bit), are latched into the input shift register through "SI." The rising edge of xCS must occur before the falling edge of SCLK for the last bit. Upon receipt of the last bit, one additional cycle of SCLK is necessary before DATA transfers from the input shift register to the addressed register. Figure 4-6 illustrates the Serial Read mode to initiate a read sequence. xCS goes low before the falling edge of SCLK. On each falling edge of SCLK, the 10 bits consisting of Start Bit = 1, OP = 1 for read, and the 8-bit ADDR are written to the serial input shift register and copied to the serial output shift register. On the next rising edge after the address LSB, the SB and 8 bits of the DATA are shifted out. The 4-wire serial interface supports multiple consecutive writes and reads, see Figure 4-5and Figure 4-7 respectively. In these cases, the address header is not needed and each additional 8 bits of data will be written into consecutive addresses. If consecutive read/write cycles are being performed, it is not necessary to insert an extra clock cycle between read/write cycles, however one extra clock cycle is needed after the last data bit of the last read/write cycle. Notes: On a Write cycle, any bits that follow the expected number of bits will be ignored. On a Read cycle, any extra clock cycles will result in the repeat of the data LSB. An invalid SB or OP renders the operation undefined. The falling edge of "xCS" always resets the serial operation for a new Read or Write cycle. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 25 Functional Descriptions Figure 4-4. 4-wire Random WRITE Timing Diagram 1 2 3 ... 10 11 12 13 14 15 16 17 18 19 20 21 SCLK tCS xCS tcs tDH SI 1 0 SB OP tCH Address[7:0] Data[7:0] tDH tDS SO Figure 4-5. 4-wire Sequential WRITE Timing Diagram 1 2 3 ... 10 11 12 13 ... 18 19 20 21 ... 26 27 ... SCLK xCS tcs tDH SI 1 0 SB OP 1st Data[7:0] Address[7:0] 2nd Data[7:0] 3rd Data[7:0] tDS SO Figure 4-6. 4-wire Random READ Timing Diagram 1 2 3 ... 10 11 12 13 14 15 16 17 18 19 20 21 SCLK xCS SI tcs tDH 1 SB 1 OP Address[7:0] SO D7 D6 D5 D4 D3 D2 D1 D0 tDD 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 26 Functional Descriptions Figure 4-7. 4-wire Sequential READ Timing Diagram 1 2 3 ... 10 11 12 13 14 ... 19 20 21 22 ... 26 27 SCLK xCS tcs SI tDH 1 SB 1 OP Address[7:0] SO 1st Data[7:0] 2nd Data[7:0] 3rd tDD Table 4-6. 4-wire Serial Interface Specifications Timing Symbol Description Min Typ Max Unit 2 -- -- ns Tds Data set-up time Tdh Data hold time 2.5 -- -- ns Tcs xCS set-up time 2 -- -- ns Tch xCS hold time 2.5 -- -- ns Tdd Read data output delay (for max load capacitor 30 pF and DVDDO@3.3 V) 2 -- 16 ns TFREQW Write 4-Wire clock Frequency -- -- 100 MHz TFREQR Read 4-Wire clock Frequency -- -- 25 MHz SCLK pulse width 45 -- 55 % TDCD 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 27 5.0 Control Register Descriptions Table 5-1. Register Summary Address Register Bit 7 Bit 6 Bit 5 00h GenConfig signal_detect mute bypass 01h OutputDriver0 output_swing0 offset_voltage0 02h OutputDriver1 output_swing1 offset_voltage1 03h Misc 04h JitterCleaner 05h CableLengthIndic ator1 Reserved 06h CableLengthIndic ator0 cable_length_ind_bit7 5.1 muteref_mode Bit 4 Bit 3 sleep mode digital_muteref rate_indicator Reserved Bit 2 Bit 1 Bit 0 Default R/W lanch_ ctrl master _rst acq_rst 08'h R/W de_emphasis0 Reserved B0'h R/W de_emphasis1 Reserved B0'h R/W jc_bypass 7C'h R/W 80'h R na R na R Reserv ed die_rev cable_leng ht_ind_bit 8 Address Register Description Address: Register Name: Default Value: Description: 00h GenConfig 08'h General Configuration Register Bit(s) Name 7 signal_detect Description Default 0b: No Signal detected Type R 1b: Signal detected 6 mute 0b: Normal operation 0b R/W 0b R/W 01b R/W 1b: Equalizer muted 5 bypass 0b: Normal operation 1b: Equalizer bypassed [4:3] sleep_mode 00b: Forced enable of the equalizer 01b: Power down when no input signal detected 10b: Forced power down of the equalizer 11b: Reserved 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 28 Control Register Descriptions Bit(s) Name 2 launch_ctrl Description 0b: Equalizer expects 800 mV launch Default Type 0b R/W 0b R/W 0b R/W Default Type 10b R/W 11b R/W 000b R/W 0b R/W 1b: Equalizer expects 400 mV (6 dB attenuation) 1 master_rst 0b: No reset 1b: Reset of registers and state machine (self clearing) 0 acq_rst 0b: No reset 1b: Reset state machine only (self clearing) Address: Register Name: Default Value: Description: 01h OutputDriver0 B0'h Output Driver 0 Configuration Register Bit(s) Name [7:6] output_swing Description 00b: Power down of driver 0 01b: 400 mV differential peak to peak swing 10b: 600 mV differential peak to peak swing 11b: 800 mV differential peak to peak swing [5:4] offset_voltage 00b: Auto mode to drive a receiver presenting a low common mode DC impedance 01b: 0.8 V output common mode 10b: 1 V output common mode 11b: 1.2 V output common mode [3:1] de_emphasis 000b: De-emphasis disable 001b: 2 dB de-emphasis 011b: 4 dB de-emphasis 101b: 6 dB de-emphasis 111b: 8 dB de-emphasis 0 21544-DSH-001-E RSVD Reserved (set to default) Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 29 Control Register Descriptions Address: Register Name: Default Value: Description: 02h OutputDriver1 B0'h Output Driver1 Configuration Register Bit(s) Name [7:6] output_swing Description 00b: Power down of driver 1 Default Type 10b R/W 11b R/W 000b R/W 0b R/W Default Type 0b R/W 1 1111b R/W 01b: 400 mV differential peak to peak swing 10b: 600 mV differential peak to peak swing 11b: 800 mV differential peak to peak swing [5:4] offset_voltage 00b: Auto mode to drive a receiver presenting a low common mode DC impedance 01b: 0.8 V output common mode 10b: 1 V output common mode 11b: 1.2 V output common mode [3:1] de_emphasis 000b: De-emphasis disable 001b: 2 dB de-emphasis 011b: 4 dB de-emphasis 101b: 6 dB de-emphasis 111b: 8 dB de-emphasis 0 RSVD Address: Register Name: Default Value: Description: Reserved (set to default) 03h Misc 7C'h MuteRef Configuration and Jitter Cleaner Bypass Register Bit(s) Name 7 muteref_mode Description 0b: Analog MuteRef with external pin voltage 1b: Digital MuteRef [6:2] digital_muteref 0 0000b: Mute when cable > 10 m 0 0010b: Mute when cable > 25 m ... 0 1010b: Mute when cable > 100 m 0 1100b: Mute when cable > 125 m 0 1111b: Mute when cable > 150 m 1 0001b: Mute when cable > 175 m 1 0100b: Mute when cable > 200 m ... 1 1001b: Mute when cable > 250 m 1 1010b: Mute when cable > 300 m 1 1011b: Mute when cable > 350 m 1 1100b: Mute when cable > 400 m 1 1110b: Mute when cable > 450 m 1 1111b: Never mute 1 RSVD Reserved (set to default) 0b R/W 0 jc_bypass 0b: Jitter cleaner active 0b R/W 1b: Jitter cleaner bypassed 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 30 Control Register Descriptions Address: Register Name: Default Value: Description: 04h JitterCleaner 00'h Jitter Cleaner Configuration and Status Register Bit(s) Name [7:6] rate_indicator Description Default Type 00b R 00b R/W 0001b R Default Type Reserved (set to default) 0b R Cable_length_ind[8]. Bit 8 of the cable length indication NA R 00b: SD rate 01b: 1.5 Gbps 10b: 3 Gbps 11b: HD rates (1.5 Gbps or 3 Gbps) [5:4] RSVD Reserved [3:0] die_rev 0000b: Die revision Address: Register Name: Default Value: Description: 05h CableLengthIndicator1 na Adaptation Results of Equalizer Bit(s) Name [7:1] RSVD 0 cable_lenght_ind_bit8 Address: Register Name: Default Value: Description: Description 06h CableLengthIndicator0 na Adaptation Results of Equalizer Bit(s) Name [7:0] cable_lenght_ind_bit[7:0] Description Cable_length[7:0]. Bits [7:0] of the cable length indication Default Type NA R NOTES: 1. A numerical value of 0 corresponds to the shortest cable. The maximum value allowed for the cable length indicator is 101111011. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 31 www.mindspeed.com General Information: Telephone: (949) 579-3000 Headquarters - Newport Beach 4000 MacArthur Blvd., East Tower Newport Beach, CA 92660 (c) 2011-2013 Mindspeed Technologies(R), Inc. All rights reserved. Information in this document is provided in connection with Mindspeed Technologies(R) ("Mindspeed(R)") products. These materials are provided by Mindspeed as a service to its customers and may be used for informational purposes only. Except as provided in Mindspeed's Terms and Conditions of Sale for such products or in any separate agreement related to this document, Mindspeed assumes no liability whatsoever. Mindspeed assumes no responsibility for errors or omissions in these materials. Mindspeed may make changes to specifications and product descriptions at any time, without notice. Mindspeed makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MINDSPEED PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MINDSPEED FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MINDSPEED SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. Mindspeed products are not intended for use in medical, lifesaving or life sustaining applications. Mindspeed customers using or selling Mindspeed products for use in such applications do so at their own risk and agree to fully indemnify Mindspeed for any damages resulting from such improper use or sale. 21544-DSH-001-E Mindspeed Technologies(R) Mindspeed Proprietary and Confidential 32