L1F3-U390100007001 - LUMILEDS HOLDING B.V.

ILLUMINATION

RoHS

COMPLIANT

With FlipChip platform technology, the LUXEON UV FC Line is the smallest

and highest power density (W/cm2) ultraviolet LED with FlipChip Technology

in a Chip Scale Package (CSP). The LED can be reowed onto a substrate

with standard surface mount (SMT) equipment and process. LUXEON UV

FC Line LEDs enable tighter beam control and high packing density of

LEDs on a chip on board solution and completely eliminate wire bonds

in the system. LUXEON UV FC Line is the ideal choice for cost sensitive

applications to achieve high irradiance at high current density, maximizing

W/$ by taking advantage of lowest thermal resistance of a CSP device.

FEATURES AND BENEFITS PRIMARY APPLICATIONS

Ultraviolet wavelength range of 380nm to 420nm for a range of options Specialty Lighting

Micro sized CSP: 1.0mm2 package for design exibility and packing density – Analytical Instrumentation

No wire bonds allows for direct attach and reow – Curing

5-sided emitter with batwing radiation pattern – Medical

Low thermal resistance for leading system level W/$ – Security

Maximum drive current of 1A/mm2 delivers superior ux for reduced

LED count

LUXEON UV FC Line

Unique LED enabling limitless

design freedom

Table of Contents

General Product Information ......................................................................2

Product Test Conditions ..............................................................................2

Part Number Nomenclature ..........................................................................2

Lumen Maintenance .................................................................................2

Environmental Compliance ...........................................................................2

Performance Characteristics ......................................................................3

Product Selection Guide..............................................................................3

Optical Characteristics ...............................................................................3

Electrical and Thermal Characteristics..................................................................3

Absolute Maximum Ratings ...........................................................................4

Characteristic Curves .............................................................................4

Spectral Power Distribution Characteristics .............................................................4

Light Output Characteristics.......................................................................5

Forward Current Characteristics.......................................................................6

Wavelength Shift ....................................................................................7

Radiation Pattern Characteristics ......................................................................8

Product Bin and Labeling Denitions ...............................................................9

Decoding Product Bin Labeling........................................................................9

Radiometric Power Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Peak Wavelength Bins...............................................................................10

Forward Voltage Bins ............................................................................11

Mechanical Dimensions..........................................................................11

Reow Soldering Guidelines ......................................................................12

JEDEC Moisture Sensitivity ...........................................................................12

Solder Pad Design ..................................................................................13

Packaging Information...........................................................................14

Pocket Tape Dimensions ............................................................................14

Reel Dimensions ...................................................................................14

General Product Information

Product Test Conditions

LUXEON UV FC Line LEDs are tested and binned with a DC drive current of 500mA at a junction temperature, Tj, of 25°C.

Part Number Nomenclature

Part numbers for LUXEON UV FC Line follow the convention below:

L A F 3 – U B B B C 0 0 0 D D D D 1

Where:

A – designates packing type (1=tape and reel)

B B B – designates minimum peak wavelength (380=380nm, 390=390nm, 400=400nm, 410=410nm)

C – designates product name and die size (1=LUXEON UV FC with 1mm2 die size)

D D D D – designates radiometric power (0300=300mW, 0350=350mW, 0400=400mW, 0450=450mW,

1400=1400mW, 1600=1600mW, etc.)

Therefore, the following part number is used for a LUXEON UV FC, with a 1mm2 die, minimum peak wavelength of 390nm and a

radiometric power of 400mW on tape and reel:

L 1 F 3 – U 3 9 0 1 0 0 0 0 4 0 0 1

Lumen Maintenance

Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the long-

term performance of this product.

Environmental Compliance

Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON UV FC Line

is compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the

RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted

materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated

diphenyl ethers (PBDE).

Performance Characteristics

Product Selection Guide

Table 1. Product performance of LUXEON UV FC Line at 500mA and 1000mA, Tj=25°C.

PEAK

WAVELENGTH [1]

(nm)

TYPICAL RADIOMETRIC POWER [2] (mW) PART NUMBER

500mA 1000mA

410–420 750 1417 LxF3-U410100007001

400–410 750 1417 LxF3-U400100007001

390–400 750 1417 LxF3-U390100007001

380–390 450 850 LxF3-U380100004001

Notes for Table 1:

1. Lumileds maintains a tolerance of ±2nm for peak wavelength measurements.

2. Lumileds maintains a tolerance of ±10% for radiometric power measurements.

Optical Characteristics

Table 2. Optical characteristics for LUXEON UV FC Line at 500mA, Tj=25°C.

PART NUMBER TYPICAL SPECTRAL

HALF-WIDTH (nm)

TYPICAL TEMPERATURE

COEFFICIENT OF PEAK

WAVELENGTH (nm/°C)

TYPICAL TOTAL

INCLUDED ANGLE [1]

TYPICAL

VIEWING ANGLE [2]

LxF3-U410x000xxxx1 13.7 0.05 170° 140°

LxF3-U400x000xxxx1 12.0 0.05 170° 140°

LxF3-U390x000xxxx1 11.0 0.05 170° 140°

LxF3-U380x000xxxx1 9.0 0.05 170° 140°

Notes for Table 2:

1. Total angle at which 90% of total luminous ux is captured.

2. Viewing angle is the o axis angle from the LED centerline where the luminous intensity is ½ of the peak value.

Electrical and Thermal Characteristics

Table 3. Electrical and thermal characteristics for LUXEON UV FC Line at 500mA, Tj=25°C.

PART NUMBER

FORWARD VOLTAGE [1] (Vf)TYPICAL TEMPERATURE

COEFFICIENT OF FORWARD

VOLTAGE [2] (mV/°C)

TYPICAL THERMAL

RESISTANCE—JUNCTION

TO SOLDER PAD (°C/W)

MINIMUM TYPICAL MAXIMUM

LxF3-U41010000xxxx1 2.8 3.1 3.4 -2.0 to -3.0 2.0

LxF3-U40010000xxxx1 2.8 3.1 3.4 -2.0 to -3.0 2.0

LxF3-U39010000xxxx1 2.8 3.1 3.4 -2.0 to -3.0 2.0

LxF3-U38010000xxxx1 2.8 3.2 3.4 -2.0 to -3.0 2.0

Notes for Table 3:

1. Lumileds maintains a tolerance of ±0.05V on forward voltage measurements.

2. Measured between 25°C and 85°C.

Absolute Maximum Ratings

Table 4. Absolute maximum ratings for LUXEON UV FC Line.

PARAMETER MAXIMUM PERFORMANCE

DC Forward Current [1,2] 1000mA

Peak Pulsed Forward Current [1,3] 1300mA

LED Junction Temperature [1] (DC & Pulse) 120°C

ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012) Class 0B

Operating Case Temperature [1] -40°C to 120°C

LED Storage Temperature -40°C to 135°C

Soldering Temperature 300 ±3°C [4]

Allowable Reow Cycles 3

Reverse Voltage (Vreverse) LUXEON UV FC Line LEDs are not designed to be driven in reverse bias

Notes for Table 4:

1. Proper current derating must be observed to maintain the junction temperature below the maximum allowable junction temperature.

2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple,” are acceptable if the following conditions are met:

– The frequency of the ripple current is 100Hz or higher

– The average current for each cycle does not exceed the maximum allowable DC forward current

– The maximum amplitude of the ripple does not exceed 15% of the maximum allowable DC forward current

3. At 10% duty cycle with pulse width of 10ms.

4. 300°C for AuSn (gold-tin) solder system, see AB116 for more details; 260°C for non-AuSn lead-free solder system per JEDEC J-STD-020E classication.

Characteristic Curves

Spectral Power Distribution Characteristics

Figure 1. Typical normalized radiant power vs. wavelength for LUXEON UV FC Line at 500mA, Tj=25°C.

Light Output Characteristics

Figure 2. Typical normalized radiant power vs. junction temperature for LUXEON UV FC Line at 500mA.

Figure 3. Typical normalized radiant power vs. forward current for LUXEON UV FC Line at Tj=25°C.

Forward Current Characteristics

Figure 4. Typical forward current vs. forward voltage for LUXEON UV FC Line at Tj=25°C.

Figure 5. Typical forward voltage shift vs. junction temperature for LUXEON UV FC Line at Tj=25°C.

Wavelength Shift

Figure 6. Typical peak wavelength shift vs. forward current for LUXEON UV FC Line at Tj=25°C.

Figure 7. Typical peak wavelength vs. junction temperature for LUXEON UV FC Line at 500mA.

Radiation Pattern Characteristics

Figure 8. Typical radiation pattern for LUXEON UV FC Line at 500mA, Tj=25ºC.

Figure 9. Typical polar radiation pattern for LUXEON UV FC Line at 500mA, Tj=25ºC.

Product Bin and Labeling Denitions

Decoding Product Bin Labeling

In the manufacturing of semiconductor products, there are variations in performance around the average values given in the

technical datasheet. For this reason, Lumileds bins LED components for luminous ux or radiometric power, color point, peak or

dominant wavelength and forward voltage.

LUXEON UV FC Line LEDs are labeled using a 4-digit alphanumeric CAT code following the format below:

A B c D

A – designates radiometric power bin (example: B=300 to 350mW, D=400 to 450mW, F=500 to 550mW)

B c – designates peak wavelength bin (example: Ax=380 to 385nm, Cx=390 to 395nm, Ex=400 to 405nm)

D – designates forward voltage bin (example: 8=2.8 to 2.9V, 0=3.0 to 3.1V)

Therefore, a LUXEON UV FC LED with a radiometric power range of 400 to 450mW, peak wavelength range of 400 to 405nm and

a forward voltage range of 3.0 to 3.1V has the following CAT code:

D E x 0

Radiometric Power Bins

Table 5 lists the standard radiometric power bins for LUXEON UV FC Line emitters. Although several bins are outlined, product

availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs.

Table 5. Radiometric power bin denitions for LUXEON UV FC Line.

BIN RADIOMETRIC POWER [1] (mW)

MINIMUM MAXIMUM

B 300 350

C 350 400

D 400 450

E 450 500

F 500 550

G 550 600

H 600 650

I 650 700

J 700 750

K 750 800

L 800 850

M 850 900

A1 400 600

B1 600 800

C1 800 1000

D1 1000 1200

E1 1200 1400

F1 1400 1600

G1 1600 1800

Notes for Table 5:

1. Lumileds maintains a tolerance of ±10% on radiometric power measurements.

Peak Wavelength Bins

Table 6. Peak wavelength denitions for LUXEON UV FC Line.

BIN PEAK WAVELENGTH [1] (nm)

MINIMUM MAXIMUM

Ax 380 385

Bx 385 390

Cx 390 395

Dx 395 400

Ex 400 405

Fx 405 410

Gx 410 415

Hx 415 420

Notes for Table 6:

1. Lumileds maintains a tolerance of ±2nm on peak wavelength measurements.

Forward Voltage Bins

Table 7. Forward voltage bin denitions for LUXEON UV FC Line.

BIN FORWARD VOLTAGE [1] (V)

MINIMUM MAXIMUM

7 2.7 2.8

8 2.8 2.9

9 2.9 3.0

0 3.0 3.1

1 3.1 3.2

2 3.2 3.3

3 3.3 3.4

4 3.4 3.5

T 2.8 3.0

V 3.0 3.2

W 3.2 3.4

X 3.4 3.6

Notes for Table 7:

1. Lumileds maintains a tolerance of ±0.05V on forward voltage measurements.

Mechanical Dimensions

Notes for Figure 10:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Figure 10. Mechanical dimensions for LUXEON UV FC Line.

ANODE

Reow Soldering Guidelines

Table 8. Reow prole characteristics for LUXEON UV FC Line (non-AuSn solder system) [1].

PROFILE FEATURE LEAD-FREE ASSEMBLY

Preheat Minimum Temperature (Tsmin) 150°C

Preheat Maximum Temperature (Tsmax) 200°C

Preheat Time (tsmin to tsmax) 60 to 120 seconds

Ramp-Up Rate (TL to Tp) 3°C / second maximum

Liquidus Temperature (TL) 217°C

Time Maintained Above Temperature TL (tL) 60 to 150 seconds

Peak / Classication Temperature (Tp) 260°C

Time Within 5°C of Actual Temperature (tp) 20 to 40 seconds

Ramp-Down Rate (Tp to TL) 6°C / second maximum

Time 25°C to Peak Temperature 8 minutes maximum

Notes for Table 8:

1. Characteristics are for non-AuSn lead-free solder system only (for AuSn (gold-tin) solder system, see AB116 for more details).

JEDEC Moisture Sensitivity

Table 9. Moisture sensitivity levels for LUXEON UV FC Line.

LEVEL FLOOR LIFE SOAK REQUIREMENTS STANDARD

TIME CONDITIONS TIME CONDITIONS

1 Unlimited ≤30°C / 85% RH 168 Hours +5 / -0 85°C / 85% RH

Time 25ºC to Peak

JEDEC J-STD-020D

Critical Zone

TL to Tp

Ramp-up

Ramp-down

Temperature

Time

Preheat Area

Tsmax

Tsmin

Figure 11. Visualization of the acceptable reow temperature prole as specied in Table 8.

Figure 12. Recommended PCB solder pad layout for LUXEON UV FC Line.

Notes for Figure 12:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Solder Pad Design

Packaging Information

Pocket Tape Dimensions

Figure 13. Pocket tape dimensions for LUXEON UV FC Line.

Reel Dimensions

Notes for Figures 13 and 14:

1. Drawings are not to scale.

2. All dimensions are in millimeters.

Figure 14. Reel dimensions for LUXEON UV FC Line.

DS185 LUXEON UV FC Line

Product Datasheet 20180604

About Lumileds

Companies developing automotive, mobile, IoT and illumination lighting applications need a partner who can collaborate with

them to push the boundaries of light. With over 100 years of inventions and industry rsts, Lumileds is a global lighting solutions

company that helps customers around the world deliver dierentiated solutions to gain and maintain a competitive edge. As the

inventor of Xenon technology, a pioneer in halogen lighting and the leader in high performance LEDs, Lumileds builds innovation,

quality and reliability into its technology, products and every customer engagement. Together with its customers, Lumileds is

making the world safer, better and more beautiful—with light.

To learn more about our lighting solutions, visit lumileds.com.

LUXEON is a registered trademark of the Lumileds

Holding B.V. in the United States and other countries.

lumileds.com

Neither Lumileds Holding B.V. nor its aliates shall be liable for any kind of loss of data or any other damages,

direct, indirect or consequential, resulting from the use of the provided information and data. Although Lumileds

Holding B.V. and/or its aliates have attempted to provide the most accurate information and data, the materials

and services information and data are provided “as is,” and neither Lumileds Holding B.V. nor its aliates

warrants or guarantees the contents and correctness of the provided information and data. Lumileds Holding

B.V. and its aliates reserve the right to make changes without notice. You as user agree to this disclaimer and

user agreement with the download or use of the provided materials, information and data. A listing of Lumileds

product/patent coverage may be accessed at lumileds.com/patents.