LTC3372 60V Low IQ Buck Controller Plus 4-Channel 8A Configurable Buck DC/DCs FEATURES DESCRIPTION HV Buck Controller: VIN = 4.5V to 60V, VOUT = 5V/3.3V nn LV Buck Regulators: V INA-H = 2.25V to 5.5V, VOUT14 0.8V nn 8x1A LV Buck Integrated Power Stages, Configurable as 2, 3 or 4 Output Channels nn 8 Unique Output Configurations (1A to 4A Per Channel) nn Low Total No-Load Input Supply Current (I ) Q nn 15A HV Controller Only (5V OUT) nn 23A HV Controller Only (3.3V OUT) nn 33A HV Controller (3.3V OUT) Plus One LV Regulator nn 9A Per Additional LV Regulator Channel nn 1MHz to 3MHz Operation (HV Runs at 1/6 Frequency) nn Programmable or Synchronizable to External Clock nn Programmable Watchdog and Power-On Reset Delay nn IC Die Temperature Monitor Output nn Thermally Enhanced 48-Pin 7mm x 7mm QFN Package The LTC(R)3372 is a highly flexible multioutput power supply IC. The device includes a high-performance, high voltage (HV) step-down DC/DC switching regulator controller that drives an all N-channel synchronous power FET stage from a 4.5V to 60V input. nn The LTC3372 also includes four low voltage (LV) synchronous buck regulators that can be programmed by the C1-C3 pins to share eight 1A integrated power stages in one of eight possible configurations. Each power stage is powered from independent inputs which may be connected to the HV buck's VOUT or to other 2.25V to 5.5V supplies. The CT pin programs timing parameters of the watchdog timer and LV outputs' Power-On Reset (RST). Precision enable thresholds facilitate reliable power-up sequencing. The LTC3372 is available in a 48-pin 7mm x 7mm QFN package. APPLICATIONS All registered trademarks and trademarks are the property of their respective owners. Automotive and Industrial Always-On Systems nn General Purpose Multi-Channel Power Supplies nn TYPICAL APPLICATION 47F x2 100k INTVCC INTVCC /GND 8.06k 90 VIN PGOOD TG VOUTPRG ITH VOUT1 1.0V 2A VOUT2 1.2V 2A VOUT VINA VINB SWA SWB FB4 EN4 VINC VIND SWC SWD VINF VINE SWF SWE FB2 FB3 EN3 TEMP WDI WDO PLLIN/MODE VOUT 3.3V/5V 3A* 47F C1 C2 C3 RSTB 3372 TA01a 70 60 50 40 30 20 10 SENSE+ - SENSE VOUT /EXTVCC VINH VING SWH SWG EN2 5m 150F x2 BG FB1 EN1 RT CT 2.2H SW LTC3372 TRACK/SS GND 0.1F BOOST 0.01F VOUT 4.7F RUN 2.2nF 100pF 80 INTVCC EFFICIENCY (%) VIN 60V MAX 4.5V MIN LV Efficiency vs Output Current 100 0 0.0001 VOUT VOUT4 2.5V 2A VOUT 100k VINA-H = 3.3V VOUT = 1.8V fSW = 2MHz VOUT3 1.8V 2A INTVCC *FULL LOAD IS EQUIVALENT TO SPECIFIED LOAD CURRENT PLUS THE FULL LOAD INPUT CURRENT FROM VOUT1-4 0.001 0.01 0.1 OUTPUT CURRENT (A) 1A Buck 2A Buck 3A Buck 4A Buck 1 4 3372 TA01b Low Voltage Buck Regulator Configurations C3 0 0 0 0 1 1 1 1 C2 0 0 1 1 0 0 1 1 C1 0 1 0 1 0 1 0 1 BUCK1 BUCK2 BUCK3 2A 2A 2A 3A 1A 2A 3A 1A 1A 4A 1A 1A 3A 2A - 4A - 2A 4A - 1A 4A - - BUCK4 2A 2A 3A 2A 3A 2A 3A 4A Rev. A Document Feedback For more information www.analog.com 1 LTC3372 TABLE OF CONTENTS Features............................................................................................................................. 1 Applications........................................................................................................................ 1 Typical Application ................................................................................................................ 1 Description......................................................................................................................... 1 Absolute Maximum Ratings...................................................................................................... 3 Order Information.................................................................................................................. 4 Electrical Characteristics......................................................................................................... 4 Typical Performance Characteristics........................................................................................... 8 Pin Functions......................................................................................................................14 Block Diagram.....................................................................................................................17 Operation..........................................................................................................................18 Low Voltage Regulators......................................................................................................................................... 20 Applications Information........................................................................................................23 High Voltage Buck Controller................................................................................................................................. 23 Low Voltage Buck Regulators................................................................................................................................ 33 Printed Circuit Board PCB Layout Considerations.................................................................................................. 35 Typical Applications..............................................................................................................37 Package Description.............................................................................................................42 Revision History..................................................................................................................43 Typical Application...............................................................................................................44 Related Parts......................................................................................................................44 2 Rev. A For more information www.analog.com LTC3372 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply (VIN) Voltage.......................... -0.3V to 65V Topside Driver (BOOST) Voltage..................-0.3V to 71V Switch (SW) Voltage...................................... -5V to 65V (BOOST-SW) Voltage.................................... -0.3V to 6V RUN Voltage............................................... -0.3V to 65V TRACK/SS, VOUT/EXTVCC, SENSE+, SENSE-, PGOOD, RT, PLL/MODE, FB1-4, EN1-4, C1-3, WDI, WDO, RST, VINA-H Voltages........................... -0.3V to 6V TG, BG.............................................................. (Note 11) ITH, VOUTPRG, CT, TEMP Voltages......................... -0.3V to (INTVCC + 0.3V) IRST, IWDO.................................................................5mA Operating Junction Temperature Range (Notes 2, 3)............................................. -40C to 150C Storage Temperature Range................... -65C to 150C PIN CONFIGURATION 48 47 46 45 44 43 42 41 40 39 38 37 PGOOD VOUTRPG ITH SENSE+ SENSE- VOUT /EXTVCC TRACK/SS VIN RUN BOOST SW TG TOP VIEW 49 GND 36 35 34 33 32 31 30 29 28 27 26 25 BG INTVCC EN4 FB4 VINH SWH SWG VING VINF SWF SWE VINE FB2 13 EN2 14 C1 15 C2 16 C3 17 RT 18 PLL/MODE 19 WDI 20 WDO 21 CT 22 EN3 23 FB3 24 RST 1 TEMP 2 EN1 3 FB1 4 VINA 5 SWA 6 SWB 7 VINB 8 VINC 9 SWC 10 SWD 11 VIND 12 UK PACKAGE 48-LEAD (7mm x 7mm) PLASTIC QFN TJMAX = 150C, JA = 34C/W EXPOSED PAD (PIN 49) IS GND, MUST BE SOLDERED TO PCB Rev. A For more information www.analog.com 3 LTC3372 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3372EUK#PBF LTC3372EUK#TRPBF LTC3372UK 48-Lead (7mm x 7mm) Plastic QFN -40C to 125C LTC3372IUK#PBF LTC3372IUK#TRPBF LTC3372UK 48-Lead (7mm x 7mm) Plastic QFN -40C to 125C LTC3372HUK#PBF LTC3372HUK#TRPBF LTC3372UK 48-Lead (7mm x 7mm) Plastic QFN -40C to 150C Contact the factory for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2), VIN = 12V, VRUN = 5V, VOUT = VINA-H = 3.3V unless otherwise noted. SYMBOL PARAMETER VIN VIN Pin Operating Voltage Range IQ (Forced Continuous/ PulseSkipping Mode) No-Load VIN Pin DC Current No-Load VOUT/EXTVCC Pin + SENSE- Pin DC Current IQ (Burst Mode) No-Load VIN Pin DC Current No-Load VOUT/EXTVCC Pin DC Current HV Controller On Only HV Controller and One LV Regulator On Additional IQ, per LV Regulator On Additional IQ, Watchdog On (Float CT Pin) Additional IQ, TEMP On (Float TEMP Pin) No-Load SENSE- Pin DC Current PLL/MODE = GND (Burst Mode) No-Load VIN Pin DC Current HV Controller On Only HV Controller and LV Regulator On Additional IQ, Watchdog On (Float CT Pin) Additional IQ, TEMP On (Float TEMP Pin) No-Load VOUT/EXTVCC Pin DC Current HV Controller On Only HV Controller and One LV Regulator On Additional IQ, per LV Regulator On Additional IQ, Watchdog On (Float CT Pin) Additional IQ, TEMP On (Float TEMP Pin) CT = TEMP = INTVCC (Watchdog VOUTPRG = l GND and TEMP Monitor Off, Unless (3.3V VOUT) Otherwise Specified) Total No-Load Input Supply Current HV Controller On Only HV Controller and One LV Regulator On Additional IQ, per LV Regulator On Additional IQ, Watchdog On (Float CT Pin) Additional IQ, TEMP On (Float TEMP Pin) PLL/MODE = GND IQ (Note 4) (Burst Mode) ISD 4 CONDITIONS MIN TYP 4.5 PLL/MODE = INTVCC or INTVCC /2 Run = VIN EN1-4 = GND No-Load VIN Pin DC Current No-Load VOUT/EXTVCC Pin + SENSE- Pin DC Current 60 UNITS V VOUTPRG = INTVCC (5V VOUT) 7 1450 A A VOUTPRG = GND (3.3V VOUT) 1300 130 A A VOUTPRG = INTVCC (5V VOUT) VIN = 12V, VINA-H = VOUT (LV Regulators Powered from HV Regulator's Output), No Load on VOUT or VOUT1-4. VIN = 12V, VINA-H = VOUT (LV Regulators Powered from HV Regulator's Output), No Load on VOUT or VOUT1-4 MAX l 4 10 A l 20 52 +26 +7 +15 0.5 46 74 +39 +12 A A A A A A 22 23 +1 +2 42 33 +4.2 A A A A l 4 29 +23 +6 +13 8.5 39 +33 +8 A A A A A l 15 31 +14 +4 +8 35 45 +20 +6 A A A A A 23 33 +9 +3 +7 46 46 +12 +7 A A A A A 3.5 8 A l VOUTPRG = INTVCC (5V VOUT) Total No-Load Input Supply Current HV Controller On Only HV Controller and One LV Regulator On Additional IQ, per LV Regulator On Additional IQ, Watchdog On (Float CT Pin) Additional IQ, TEMP On (Float TEMP Pin) VOUTPRG = l CT = TEMP = INTVCC (Watchdog GND (3.3V V ) OUT and TEMP Monitor Off, unless otherwise specified) VIN Pin Current in Shutdown RUN = EN1-4 = GND 2 Rev. A For more information www.analog.com LTC3372 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2), VIN = 12V, VRUN = 5V, VOUT = VINA-H = 3.3V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 4.875 3.217 5.000 3.300 5.125 3.383 V V 1.17 1.22 50 1.27 V mV High Voltage Buck Controller VOUT Regulated Output Voltage (Note 5) ITH = 0.7V to 2V VOUTPRG = INTVCC, VIN = 6V to 60V VOUTPRG = GND, VIN = 4.5V to 60V VRUN RUN Pin Controller Enable Threshold RUN Pin Voltage Rising Hysteresis IRUN RUN Pin Pull-Up Current RUN = 0V gm Error Amplifier Transconductance (Note 5) ITH = 1.2V, Sink/Source 5A ITRACK/SS Soft-Start Charge Current TRACK/SS = 0V ISENSE+ SENSE+ Pin Current VSENSE(MAX) Maximum Current Sense Threshold SENSE- = 3.3V DMAX(HV) Maximum Duty Cycle In Dropout RRT = 400k TG l l 0.5 A 2 7 10 mS 14 A 1 A 82 mV 68 75 97.5 98 % Top Gate Pull-Up On-Resistance Top Gate Pull-Down On-Resistance 2.3 1.5 BG Bottom Gate Pull-Up On-Resistance Bottom Gate Pull-Down On-Resistance 2.4 1.1 tD(TG/BG) Delay Time, Top Gate Off to Bottom Gate On (Note 6) 40 ns tD(BG/TG) Delay Time, Bottom Gate Off to Top Gate On (Note 6) 18 ns tON(MIN) Minimum On-Time (Top Gate) (Note 7) 60 ns PGOOD PGOOD Pin Voltage When Low PGOOD Pin Leakage Current When High IPGOOD = 2mA PGOOD = 5V 0.2 0.4 1 V A UV VOUT /EXTVCC Pin Undervoltage Threshold Falling, Relative to Regulated VOUT Hysteresis -5 -7.5 2.5 -10 % % OV VOUT /EXTVCC Pin Overvoltage Threshold Rising, Relative to Regulated VOUT Hysteresis +5 +7.5 2.5 +10 % % SENSE- Pin Overvoltage Threshold Rising, Relative to Regulated VOUT Hysteresis +15 2.5 % % tPGOOD PGOOD Delay for Reporting OV/UV Fault PGOOD High to Low 40 s INTVCC No Load Internal VCC Regulated Voltage INTVCC Voltage Load Regulation 6V < VIN < 60V IINTVCC = 0mA to 50mA No Load Internal VCC Voltage Source Resistance IINTVCC = 0mA to 50mA VOUT Threshold for INTVCC Switchover from VIN to VOUT VOUT Rising Hysteresis Undervoltage Lockout (UVLO) Threshold on INTVCC INTVCC Voltage Rising INTVCC Voltage Falling Internal Bias Start Up Time VOUT = 0V l VOUT = 3.3V 4.9 5.1 -1 5.3 -2 5 -2.5 VOUT = 5V 4.5 l l 3.6 V % V 4.7 0.25 4.9 V V 4.0 3.8 4.25 4.0 V V 1.2 ms Oscillator and Phase-Locked Loop fOSC Frequency of Internal Oscillator (LV Regulators' Switching Frequency) VRT = INTVCC VRT = INTVCC RRT = 400k l l 1.9 1.75 1.85 fSW HV Controller Switching Frequency fPLL/MODE Synchronization Frequency Range tLOW, tHIGH > 60ns l 1 VPLL/MODE PLL/MODE Level High PLL/MODE Level Low For Synchronization For Synchronization l l 1.3 VRT RT Servo Voltage RRT = 400k l 770 2 2 2 2.1 2.25 2.15 1/6*fOSC kHz 3 0.25 800 MHz MHz MHz 825 MHz V V mV Rev. A For more information www.analog.com 5 LTC3372 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2), VIN = 12V, VRUN = 5V, VOUT = VINA-H = 3.3V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 200 220 240 mV Temperature Monitor VTEMP(ROOM) TEMP Voltage at 25C VTEMP/C VTEMP Slope 7 mV/C OT Overtemperature Shutdown 170 C OT Hyst Overtemperature Hysteresis 10 C Low Voltage (LV) Buck Regulators VINA-H Input Operating Voltage l 2.25 5.5 V VOUT1-4 Regulated Output Voltage Set Point l 0.8 VINA-H V UVLO Undervoltage Lockout Threshold on VINA-H VINA-H Falling VINA-H Rising l l 1.95 2.05 2.05 2.15 2.15 2.25 V V IQ(VINA-H) Quiescent Current into VINA-H Pins, Per Enabled LV Regulator (Note 8) Burst Mode, FB1-4 = 0.82V Forced Continuous Mode, FB1-4 = 0V 25 400 35 550 A A ISD(VINA-H) Shutdown Current into VINA-H Pins 0 1 A VFB1 VFB2-4 IFB1-4 Feedback Leakage Current FB1-4 = 0.85V DMAX Maximum Duty Cycle FB1-4 = 0V RPMOS PMOS On-Resistance ISW = 100mA, 1A - Per Power Stage 290 m RNMOS NMOS On-Resistance ISW = -100mA, 1A - Per Power Stage 180 m ILEAKP PMOS Leakage Current EN1-4 = GND -1 1 A ILEAKN NMOS Leakage Current EN1-4 = GND -1 1 A tSS Soft-Start Time (Note 10) UV Rising Undervoltage RST Threshold Regulator 1 Regulated Feedback Voltage for Regulator 1 l 792 800 808 mV Regulated Feedback Voltage for Regulators 2-4 l 780 800 820 mV 50 nA -50 l 100 % 0.25 1.5 3 ms % Relative to Regulated VFB Hysteresis l -4 -2 1 -1 % % Rising RST Undervoltage Threshold Regulators 2-4 % Relative to Regulated VFB Hysteresis l -7 -5 1 -3 % % OV RST Overvoltage Threshold of Regulators 1-4 % Relative to Regulated VFB Hysteresis l +5 +7.5 -3 +10 % % ILIM PMOS Current Limit 1 Buck with 1 Power Stage (Note 9) 1.4 1.8 2.2 A 1 Buck with 2 Power Stages (Note 9) 3.6 A 1 Buck with 3 Power Stages (Note 9) 5.4 A 1 Buck with 4 Power Stages (Note 9) 7.2 A Interface Logic Pins (RST, WDO, WDI, CT, C1, C2, C3) IOH Output High Leakage Current RST, WDO 5.5V at Pin VOL Output Low Voltage RST, WDO 3mA at Pin VIH WDI Input High Threshold l 0.1 A 0.4 V 1.2 CT, C1, C2, C3 Input High Threshold l INTVCC - 0.4 VIL WDI, C1, C2, C3 Input Low Threshold l tWDI(WIDTH) WDI Pulse Width l 6 1 V V 0.4 80 V ns Rev. A For more information www.analog.com LTC3372 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C (Note 2), VIN = 12V, VRUN = 5V, VOUT = VINA-H = 3.3V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Interface Logic Pins (EN1, EN2, EN3, EN4) VEN Enable Rising Threshold All LV Regulators Disabled l 400 730 1200 mV Enable Rising Threshold At Least One LV Regulator Enabled l 380 400 420 mV l 290 315 340 mV 1 A Enable Falling Threshold IEN Enable Pin Leakage Current EN = 3.3V CT Timing Parameters; CT = 10nF tWDIO Time from WDO Low Until Next WDO Low CT = 10nF 9.7 12.9 16.1 s tWDI Time from Last WDI Until Next WDO Low CT = 10nF 1.22 1.62 2.03 s tWDO WDO Low Time Absent a Transition at WDI CT = 10nF 160 202 280 ms tRST RST Assertion Delay CT = 10nF 160 202 280 ms tWDL Watchdog Lower Boundary CT = 10nF 38 50.6 63 ms Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3372 is tested under pulsed load conditions such that TJ TA. The LTC3372E is guaranteed to meet specifications from 0C to 85C operating junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3372I is guaranteed over the -40C to 125C operating junction temperature range. The LTC3372H is guaranteed over the -40C to 150C operating junction temperature range. High junction temperatures degrade operating lifetimes; operating lifetime is derated for junction temperatures greater than 125C. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. The junction temperature (TJ in C) is calculated from the ambient temperature (TA in C) and power dissipation (PD in Watts) according to the formula: TJ = TA + (PD * JA) where JA (in C/W) is the package thermal impedance. Note 3: This IC includes overtemperature protection which protects the device during momentary overload conditions. Junction temperatures will exceed 150C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 4: The IQ (Total Input Supply Quiescent Current) is the total average current drawn from the input power supply by a typical application in Burst Mode with no load currents (from either the HV Controller VOUT or the LV Regulators' VOUT1-4). Note 5: The HV Controller's output regulation is tested in a feedback loop that servos the ITH pin to a specified voltage and measures the resulted voltage at VOUT/EXTVCC pin. Note 6: Delays are measured using 50% levels, with TG and BG driving minimum capacitive load. Note 7: The minimum on-time conditions is specified for an inductor peak-to-peak ripple current 40% of IMAX (see Minimum On-Time Considerations in the Applications Information section). Note 8: The IQ(VINA-H) (Quiescent Current into VINA-H Pins) are measured with power switches not switching. Dynamic supply current when switching may be higher due to the gate charge being delivered. Note 9: The current limit features are intended to protect the IC from short term or intermittent fault conditions. Continuous operation above the maximum specified pin current rating may result in device degradation over time. Note 10: The soft-start is the time from the first top switch turn on, after an enable rising, until the feedback has reached 90% of its nominal regulation voltage. Note 11: Do not apply a voltage or current source to these pins. They must be connected to the gates of the external power MOSFETs, otherwise permanent damage may occur. Rev. A For more information www.analog.com 7 LTC3372 TYPICAL PERFORMANCE CHARACTERISTICS (HV Controller) TA = 25C, unless otherwise noted. Efficiency and Power Loss vs Output Current 90 VIN = 12V BURST EFFICIENCY VOUT = 3.3V 60 FCM LOSS PULSE-SKIPPING LOSS 1000 80 100 50 BURST LOSS 40 10 30 PULSE-SKIPPING EFFICIENCY 20 10 0 0.0001 1 70 60 PULSE-SKIPPING LOSS 0.001 0.01 0.1 1 OUTPUT CURRENT (A) 10 100 50 BURST LOSS 40 30 0 0.0001 FCM EFFICIENCY 0.001 0.01 0.1 1 OUTPUT CURRENT (A) 3372 G01 80 98 VOUT = 5V 92 88 VOUT = 3.3V 86 84 82 80 SUPPLY CURRENT (A) EFFICIENCY (%) 96 90 50 HV Only HV+1LV HV Only HV+1LV 70 94 fSW = 333kHz ILOAD = 5A 60 50 VOUT = 3.3V 40 20 0 5 10 15 20 25 30 35 40 45 50 55 60 INPUT VOLTAGE (V) 35 10 25 20 15 10 3.45 3.40 3.35 3.30 3.25 VOUT = 5V 5 0 -75 -50 -25 5 10 15 20 25 30 35 40 45 50 55 60 INPUT VOLTAGE (V) 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G05 Output Voltage vs Temperature Forced Continuous Mode 3.50 VIN = 12V 3.45 8 7 OUTPUT VOLTAGE (V) VIN SHUTDOWN CURRENT (A) 9 3.50 VOUT = 3.3V 30 Shutdown Current vs Temperature 3.55 HV Only HV+1LV HV Only HV+1LV 6 5 4 3 2 5.10 VIN = 12V ILOAD = 100mA 3.40 5.05 VOUT = 5V 5.00 4.95 3.35 3.30 VOUT = 3.3V 4.90 OUTPUT VOLTAGE (V) VIN SHUTDOWN CURRENT (A) 40 VIN = 12V 3372 G04 Shutdown Current vs VIN 3.60 4.85 3.25 1 5 10 15 20 25 30 35 40 45 50 55 60 INPUT VOLTAGE (V) 3372 G06 8 45 10 3.65 3.20 VOUT = 5V 30 3372 G03 3.70 Burst Mode Quiescent Current vs Temperature SUPPLY CURRENT (A) 100 0.1 10 3372 G02 Burst Mode Quiescent Current vs VIN Efficiency vs VIN 10 PULSE-SKIPPING EFFICIENCY 1 20 0.1 1000 FCM LOSS 10 FCM EFFICIENCY 10000 VIN = 12V BURST EFFICIENCY 90 VOUT = 5V POWER LOSS (mW) 70 100 POWER LOSS (mW) EFFICIENCY (%) 80 10000 EFFICIENCY (%) 100 Efficiency and Power Loss vs Output Current 0 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G07 3.20 -75 -50 -25 4.80 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G08 Rev. A For more information www.analog.com LTC3372 TYPICAL PERFORMANCE CHARACTERISTICS (HV Controller) TA = 25C, unless otherwise noted. 3.318 5.010 3.316 5.009 VOUT = 5V 3.314 5.008 3.312 5.007 VOUT = 3.3V 5.006 3.308 5.005 3.306 5.004 5 10 15 20 25 30 35 40 45 50 55 60 INPUT VOLTAGE (V) 80 78 76 74 72 70 68 66 64 62 60 0 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) 80 Maximum Current Sense Voltage vs ITH Voltage 900 PULSE-SKIPPING MODE 700 20 0 -40 5.25 600 500 400 300 200 100 -20 FORCED CONTINUOUS MODE 0 0.2 0.4 0.6 0.8 VITH (V) 1.0 -100 1.4 3 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0 SENSE- VOLTAGE (V) 3372 G11 INTVCC Voltage vs Gate Charge Current VOUT = 5V 5.25 INTVCC VOLTAGE (V) INTVCC VOLTAGE (V) 5.10 5.05 5.00 4.95 4.90 4.85 5.00 4.75 4.50 4.25 4.80 5 10 15 20 25 GATE CHARGE CURRENT (mA) 30 3372 G14 VIN = 4.5V 4.25 3.75 0 5 10 15 20 25 GATE CHARGE CURRENT (mA) 30 3372 G13 Current Limit in Foldback 5.50 0 4.50 3372 G12 5.20 4.75 4.75 INTVCC Line Regulation in Dropout 5.15 VIN = 12V VIN = 6V 4.00 0 1.2 INTVCC Voltage vs Gate Charge Current VOUT = 3.3V 5.00 INTVCC VOLTAGE (V) 40 Burst Mode OPERATION 5.25 FORCED CONTINUOUS MODE VIN = 12V VOUT = 5V 800 60 3372 G10 SENSE- Pin Input Bias Current SENSE- CURRENT (A) MAXIMUM CURRENT SENSE VOLTAGE (mV) 3372 G09 VOUT = 3.3V GATE CHARGE CURRENT = 10mA 4.00 4.50 4.75 5.00 5.25 5.50 5.75 6.00 6.25 6.50 INPUT VOLTAGE (V) 3372 G15 MAXIMUM CURRENT SENSE VOLTAGE (mV) 3.310 MAXIMUM CURRENT SENSE VOLTAGE (mV) Maximum Current Sense Threshold vs Duty Cycle OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) Output Voltage Line Regulation Forced Continuous Mode 80 70 60 50 40 30 20 0 10 20 30 40 50 60 70 80 90 100 VOUT TO REGULATED VOLTAGE RATIO (%) 3372 G16 Rev. A For more information www.analog.com 9 LTC3372 TYPICAL PERFORMANCE CHARACTERISTICS (HV Controller) TA = 25C, unless otherwise noted. TRACK/SS Pull-Up Current vs Temperature 1.275 11.0 10.5 RUN PIN VOLTAGE (V) TRACK/SS CURRENT (A) 4.20 1.300 VIN = 5V 11.5 Undervoltage Lockout Threshold vs Temperature 10.0 9.5 9.0 8.5 8.0 VIN = 12V 4.10 1.250 1.225 RISING 1.200 FALLING 1.175 1.150 7.5 7.0 -75 -50 -25 1.100 -75 -50 -25 4.00 3.95 3.90 0 25 50 75 100 125 150 TEMPERATURE (C) 3.70 -75 -50 -25 3372 G19 Load Step Forced Continuous Mode Load Step Pulse-Skipping Mode ILOAD 5A/DIV ILOAD 5A/DIV ILOAD 5A/DIV IIND 5A/DIV IIND 5A/DIV IIND 5A/DIV VOUT AC-COUPLED 100mV/DIV VOUT AC-COUPLED 100mV/DIV 3372 G20 3372 G21 100s/DIV VIN = 12V VOUT = 3.3V ILOAD = 100mA to 8A VIN = 12V VOUT = 3.3V ILOAD = 100mA to 8A Inductor Current at Light Load 100s/DIV VIN = 12V VOUT = 3.3V ILOAD = 100mA to 8A 3372 G22 Soft Start-Up FORCED CONTINUOUS 2A/DIV VIN 5V/DIV BURST 2A/DIV VOUT = 5V PULSESKIPPING 2A/DIV VOUT = 3.3V VOUT 2V/DIV VIN = 12V VOUT = 3.3V ILOAD = 200A 10 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G18 Load Step Burst Mode Operation 100s/DIV FALLING 3.85 3.75 3372 G17 VOUT AC-COUPLED 100mV/DIV RISING 4.05 3.80 1.125 0 25 50 75 100 125 150 TEMPERATURE (C) 4.15 INTVCC VOLTAGE (V) 12.0 Shutdown (RUN) Threshold vs Temperature 5s/DIV 3372 G23 2ms/DIV 3372 G24 Rev. A For more information www.analog.com LTC3372 TYPICAL PERFORMANCE CHARACTERISTICS (LV Buck Regulator) TA = 25C, unless otherwise noted. 2A Buck Efficiency and Power Loss vs Output Current 10000 BURST EFFICIENCY 90 1000 100 50 FCM LOSS 40 30 10 BURST LOSS EFFICIENCY (%) FCM EFFICIENCY 60 1 20 VIN = 3.3V VOUT = 1.8V 10 0 0.0001 0.001 0.01 0.1 OUTPUT CURRENT (A) 1 2 70 ILOAD = 100mA 60 50 40 30 VOUT = 1.8V fSW = 2MHz 20 0 ILOAD = 10mA 2 2.5 3 3.5 4 4.5 INPUT VOLTAGE (V) 5 3372 G25 2A Buck Efficiency vs VOUT Forced Continuous Mode EFFICIENCY (%) 100 ILOAD = 1A 95 80 60 50 ILOAD = 10mA 40 30 20 ILOAD = 1mA 10 VIN = 3.3V fSW = 2MHz 2A Buck Efficiency vs VOUT Burst Mode Operation 85 80 ILOAD = 1mA ILOAD = 10mA ILOAD = 10mA ILOAD = 1A 30 20 10 0 0.0001 FCM VIN = 3.3V VOUT = 1.8V fSW = 1MHz fSW = 2MHz fSW = 3MHz 0.001 0.01 0.1 OUTPUT CURRENT (A) 1 2 40 30 10 VIN = 3.3V VOUT = 1.8V fSW = 2MHz 0 0.0001 0.001 0.01 0.1 OUTPUT CURRENT (V) 1.800 VIN = 3.3V VOUT = 1.8V 1.790 800 798 796 4 1A Buck Load Regulation Across VIN Forced Continuous Mode VOUT = 1.8V 1.770 1.760 1.750 1.740 1.730 1.720 794 1.710 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G32 3372 G31 1 1.780 802 792 -75 -50 -25 1A Buck 2A Buck 3A Buck 4A Buck 3372 G30 OUTPUT VOLTAGE (V) 40 50 2A Buck Regulator Feedback Voltage vs Temperature 804 5.5 60 3372 G29 REGULATED FEEDBACK VOLTAGE (mV) EFFICIENCY (%) 50 5 70 20 806 60 3 3.5 4 4.5 INPUT VOLTAGE (V) 80 70 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 OUTPUT VOLTAGE (V) 100 70 2.5 100 90 2A Buck Efficiency vs Output Current Across Switching Frequency BURST MODE 2 90 3372 G28 80 ILOAD = 1mA ILOAD = 10mA ILOAD = 100mA ILOAD = 1A Efficiency vs Output Current Burst Mode Operation VIN = 3.3V fSW = 2MHz 75 0 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 OUTPUT VOLTAGE (V) 90 80 3372 G27 ILOAD = 100mA 70 85 70 5.5 EFFICIENCY (%) 90 90 3372 G26 EFFICIENCY (%) 100 VOUT = 1.8V fSW = 2MHz 75 ILOAD = 1mA 10 0.1 2A Buck Efficiency vs VIN Burst Mode 95 80 POWER LOSS (mW) 70 100 ILOAD = 1A 90 80 EFFICIENCY (%) 100 EFFICIENCY (%) 100 2A Buck Efficiency vs VIN Forced Continuous Mode 1.700 0.001 VIN = 2.25V VIN = 3.3V VIN = 5V 0.01 0.1 OUTPUT CURRENT (A) 1 3372 G33 Rev. A For more information www.analog.com 11 LTC3372 TYPICAL PERFORMANCE CHARACTERISTICS (LV Buck Regulator) TA = 25C, unless otherwise noted. 2A Buck Regulated Feedback Voltage vs VINA-H 808 VOUT = 1.8V REGULATED FEEDBACK VOLTAGE (mV) 1.820 OUTPUT VOLTAGE (V) 1.800 1.780 1.760 1.740 1.720 1.700 0.001 VIN = 2.25V VIN = 3.3V VIN = 5V 0.01 0.1 OUTPUT CURRENT (A) 1 804 VFB1 798 ILOAD = 10mA ILOAD = 1A 794 2 2.5 2.10 VIN = 3.3V 2.08 2.06 2.04 2.5 2.0 1.5 Default Oscillator Frequency vs Temperature 1400 VINA-H = 3.3V 2.06 1.90 -75 -50 -25 Enable Threshold vs Temperature 900 VIN = 3.3V 800 800 600 400 -200 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G39 EN THRESHOLD (mV) VTEMP (mV) 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G40 12 1.90 -75 -50 -25 VTEMP vs Temperature 700 600 RISING 500 400 FALLING 300 0 1.92 1.98 1.92 200 1.94 2.00 1.94 1000 2.04 1.96 2.02 1.96 1200 1.98 RT = 402k VINA-H = 3.3V 3372 G38 3372 G37 2.00 0 25 50 75 100 125 150 TEMPERATURE (C) RT Programmed Oscillator Frequency vs Temperature 0 250 300 350 400 450 500 550 600 650 700 750 800 RT (k) 0 25 50 75 100 125 150 TEMPERATURE (C) 2.02 VIN = 3.3V VIN = 5V 3372 G36 0.5 NMOS 100 -75 -50 -25 FSW (MHz) 1.50 -75 -50 -25 5.5 1.0 150 2.08 5 FSW (MHz) FSW (MHz) PMOS RESISTANCE (m) 4.0 200 2.10 3 3.5 4 4.5 INPUT VOLTAGE (V) 3.0 250 1.65 1.55 Oscillator Frequency vs RT 3.5 300 1.70 3372 G35 PMOS 350 1.75 1.60 796 VIN = 5V VIN = 3.3V VIN = 2.25V 400 1.80 800 1A Buck NMOS and PMOS RDS(ON) vs Temperature Across VIN 450 1.85 802 3372 G34 500 1.90 FORCED CONTINUOUS MODE VIN = 3.3V VFB2 VOUT = 1.8V 806 792 4 1A Buck PMOS Current Limit vs Temperature CURRENT LIMIT (A) 4A Buck Output Voltage vs Output Current 0 25 50 75 100 TEMPERATURE (C) 125 150 3372 G41 200 -75 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G42 Rev. A For more information www.analog.com LTC3372 TYPICAL PERFORMANCE CHARACTERISTICS (LV Buck Regulator) TA = 25C, unless otherwise noted. Precise Enable Threshold vs Temperature 420 410 UVLO THRESHOLD (V) 390 380 370 360 350 FALLING 2.20 IIND 1A/DIV RISING 2.15 2.10 VOUT AC-COUPLED 50mV/DIV 2.05 FALLING 2.00 100s/DIV VIN = 3.3V VOUT = 1.8V ILOAD = 100mA to 1.6A 1.95 330 320 -75 -50 -25 ILOAD 1A/DIV 2.25 RISING 340 2A Buck Load Step Burst Mode 2.30 VIN = 3.3V 400 EN THRESHOLD (mV) VINA-H UVLO Threshold vs Temperature 0 25 50 75 100 125 150 TEMPERATURE (C) 1.90 -75 -50 -25 3372 G43 0 25 50 75 100 125 150 TEMPERATURE (C) 3372 G45 3372 G44 2A Buck Load Step Forced Continuous Mode 2A Buck Start-Up ILOAD 1A/DIV VIN 1V/DIV IIND 1A/DIV VOUT AC-COUPLED 50mA/DIV VOUT 1V/DIV 100s/DIV VIN = 3.3V VOUT = 1.8V ILOAD = 100mA to 1.6A 3372 G46 VIN = 3.3V VOUT = 1.8V 2ms/DIV 3372 G47 Rev. A For more information www.analog.com 13 LTC3372 PIN FUNCTIONS RST (Pin 1): LV Regulator Reset Logic Output. This pin is pulled low when the feedback pin (FB1-4) voltage of any enabled LV regulator is outside of its power good window. The window is -2% to +7.5% (typical) for regulator 1, and -5% to +7.5% (typical) for regulators 2-4, around the regulated 0.8V level. This pin is pulled low when all LV regulators are disabled. Assertion (the pin goes high) delay is scaled by the CT capacitor. TEMP (Pin 2): Temperature Indication Pin. TEMP outputs a voltage of 220mV (typical) at 25C. The TEMP voltage will increase by 7mV/C (typical) at higher temperatures giving an external indication of the IC's internal die temperature. The temperature monitor can be shut down by tying the TEMP pin to INTVCC to reduce quiescent current. If all LV regulators are disabled, the temperature monitor shuts down and the TEMP pin becomes high impedance. EN1 (Pin 3): LV Buck Regulator 1 Enable Input. Active high. Do not float. FB1 (Pin 4): LV Buck Regulator 1 Feedback Pin. Receives feedback by a resistor divider connected across the output. VINA (Pin 5): LV Power Stage A Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. SWA (Pin 6): LV Power Stage A Switch Node. External inductor connects to this pin. SWB (Pin 7): LV Power Stage B Switch Node. External inductor connects to this pin. VINB (Pin 8): LV Power Stage B Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. VINC (Pin 9): LV Power Stage C Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. SWC (Pin 10): LV Power Stage C Switch Node. External inductor connects to this pin. SWD (Pin 11): LV Power Stage D Switch Node. External inductor connects to this pin. VIND (Pin 12): LV Power Stage D Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. 14 FB2 (Pin 13): LV Buck Regulator 2 Feedback Pin. Receives feedback by a resistor divider connected across the output. In configurations where LV Regulator 2 is not used, FB2 should be tied to ground. EN2 (Pin 14): LV Buck Regulator 2 Enable Input. Active high. In configurations where LV Regulator 2 is not used, tie EN2 to ground. Do not float. C1 (Pin 15): LV Regulator Configuration Control Input Bit. With C2 and C3, C1 configures the buck output current power stage combinations. C1 should either be tied to INTVCC or ground. Do not float. C2 (Pin 16): LV Regulator Configuration Control Input Bit. With C1 and C3, C2 configures the buck output current power stage combinations. C2 should either be tied to INTVCC or ground. Do not float. C3 (Pin 17): LV Regulator Configuration Control Input Bit. With C1 and C2, C3 configures the buck output control power stage combinations. C3 should either be tied to INTVCC or ground. Do not float. RT (Pin 18): Oscillator Frequency Pin. This pin provides two modes of setting the switching frequency. Connecting a resistor from RT to ground will set the switching frequency based on the resistor value. If RT is tied to INTVCC the internal 2MHz oscillator will be used. Do not float. PLL/MODE (Pin 19): Oscillator Synchronization Input and Mode Select Pin. Driving this pin with an external clock signal synchronizes the internal oscillator to the applied clock. The LV bucks synchronize to the oscillator frequency and HV buck synchronizes to 1/6th frequency when in forced continuous mode. When no external clock is applied the oscillator frequency is programmed by the RT pin. When not synchronizing to an external clock this input determines how the controller and regulators operate at light load. Floating or grounding this pin selects Burst Mode operation, and tying this pin to INTVCC forces continuous inductor current mode operation for all the converters and the controller. Tying this pin to a voltage greater than 1.2V and less than INTVCC-1.3V selects pulse-skipping mode operation for the controller, but Burst Mode operation for the low voltage converters. This pin has a 100k internal resistor to ground. Rev. A For more information www.analog.com LTC3372 PIN FUNCTIONS WDI (Pin 20): Watchdog Timer Input. The WDI pin must be toggled either low to high or high to low every 1.62 seconds. Failure to toggle WDI results in the WDO pin being pulled low for 202ms. All times correspond to a 10nF capacitor on the CT pin. WDO (Pin 21): Watchdog Timer. Open-drain output. WDO is pulled low for 202ms during a watchdog timeout period. The WDO pin pulls low if the WDI input does not transition in less than 1.62 seconds since its last transition or 12.9 seconds after a watchdog timeout period. An UVLO event resets the watchdog timer and WDO asserts itself low for the 202ms watchdog timeout period. All times correspond to a 10nF capacitor on the CT pin. CT (Pin 22): Timing Capacitor Pin. A capacitor connected to GND sets a time constant which is scaled for use by the WDI, WDO, and RST pins. Tying the CT pin to INTVCC disables the watchdog timer to reduce quiescent current. EN3 (Pin 23): LV Buck Regulator 3 Enable Input. Active high. In configurations where LV Regulator 3 is not used, tie EN3 to ground. Do not float. FB3 (Pin 24): LV Buck Regulator 3 Feedback Pin. Receives feedback by a resistor divider connected across the output. In configurations where LV Regulator 3 is not used, FB3 should be tied to ground. VINE (Pin 25): LV Power Stage E Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. SWE (Pin 26): LV Power Stage E Switch Node. External inductor connects to this pin. SWF (Pin 27): LV Power Stage F Switch Node. External inductor connects to this pin. VINH (Pin 32): LV Power Stage H Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. FB4 (Pin 33): LV Buck Regulator 4 Feedback Pin. Receives feedback by a resistor divider connected across the output. EN4 (Pin 34): LV Buck Regulator 4 Enable Input. Active high. Do not float. INTVCC (Pin 35): Internal VCC Pin. Output of an internal linear low-dropout (LDO) regulator powered from VIN. The HV buck gate drive and control circuits are powered from this voltage source when VOUT is < 4.7V. When VOUT > 4.7V the bias connects to Vout and the LDO is shutdown. Must be de-coupled to GND pin with a minimum of 4.7F low ESR (ceramic) capacitor. BG (Pin 36): HV Controller High Current Gate Drive for Bottom (Synchronous) N-channel MOSFET. Voltage swing at this pin is from ground to INTVCC. TG (Pin 37): HV Controller High Current Gate Drive for Top N-channel MOSFET. This is the output of floating driver with a voltage swing equal to INTVCC superimposed on the switch node voltage SW. SW (Pin 38): HV Controller Switch Node Connection to Inductor. BOOST (Pin 39): HV Controller Bootstrapped Supply to the Topside Floating Driver. A capacitor should be connected between the BOOST and SW pin and a Schottky diode should be connected between the BOOST and INTVCC pins. Voltage swing at the BOOST pin is from INTVCC to (VIN + INTVCC). VINF (Pin 28): LV Power Stage F Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. RUN (Pin 40): HV Controller Enable Input. Forcing this pin above 1.2V turns on the HV controller. This pin has a 0.5A internal pull-up current from ground to around 4V, and can be forced up to 65V (absolute maximum). VING (Pin 29): LV Power Stage G Input Supply. Bypass to GND with a 10F or larger ceramic capacitor. VIN (Pin 41): HV Input Supply Pin. A bypass capacitor should be tied between this pin and the GND pin. SWG (Pin 30): LV Power Stage G Switch Node. External inductor connects to this pin. TRACK/SS (Pin 42): HV Controller External Tracking and Soft-Start Input. When this pin is above 1.2V, the controller regulates the output voltage VOUT to the programed 5V or 3.3V level. When this pin is below 1.2V, the output voltage SWH (Pin 31): LV Power Stage H Switch Node. External inductor connects to this pin. Rev. A For more information www.analog.com 15 LTC3372 PIN FUNCTIONS is regulated proportionally lower. An internal 10A pullup current source is connected to this pin. A capacitor to ground at this pin sets the ramp time to the final regulated output voltage. Alternatively, a resistor divider on another voltage supply connected to this pin allows the controller's output to track another supply during start-up. SENSE+ (Pin 45): HV Controller Positive (+) Input to Differential Current Comparator. The ITH pin voltage and controlled offsets between the SENSE- and SENSE+ pins set the current trip threshold. The current comparator can be used for either inductor DCR sensing or traditional current sensing resistor (RSENSE) sensing. VOUT/EXTVCC (Pin 43): HV Controller Output Voltage Sensing and External VCC Power Input. Connect this pin to the HV controller's regulated output voltage. The HV controller VOUT is regulated to either 3.3V or 5V by an internal resistor divider selected by the VPROG pin. This pin is also provides an external VCC connection and supplies internal bias voltages from VOUT to improve low IQ performance and reduce power loss. ITH (Pin 46): HV Controller Error Amplifier Output and Compensation Point. The current comparator threshold increases with this control voltage. SENSE- (Pin 44): HV Controller Negative (-) Input to Differential Current Comparator. This SENSE- pin also functions as the output voltage sense pin for a secondary 15% overvoltage protection in addition to the 7.5% overvoltage protection at the VOUT/EXTVCC pin. In the situation that SENSE- pin is separated from VOUT/EXTVCC pin to achieve point-of-load (POL) regulation, SENSE- can begin drawing a >500A current when SENSE- is 200mV greater than VOUT (VOUT = 5V) or INTVCC (VOUT = 3.3V). When voltage on SENSE- pin is close to INTVCC, SENSE- can begin drawing >500A current. Do not connect a filtering resistor in series with SENSE- pin unless SENSE- stays close to ground in the application. 16 VOUTPRG (Pin 47): HV Controller Output Voltage Programming Pin. When this pin is tied to INTVCC, the output voltage is regulated to 5V. When tied to ground, the output voltage is regulated to 3.3V. PGOOD (Pin 48): HV Controller Power Good Open-Drain Logic Output. This pin is pulled low when the voltage at the VOUT/EXTVCC pin is outside of the 7.5% window around the regulated level, or voltage at SENSE- pin is more than 15% above the regulated level of VOUT. GND (Exposed Pad Pin 49): Ground. The exposed pad must be soldered to a continuous printed circuit board ground plane directly under the IC package for rated thermal performance. The exposed pad is a shared ground for signal grounds, driver ground and power stage grounds of all HV and LV buck regulators. Rev. A For more information www.analog.com LTC3372 BLOCK DIAGRAM VIN INTVCC DB OV BOOST 1.29V + PGOOD - VFB + UV CB DROP OUT DET LTC3372: CLK/6 (1/6 fOSC) 1.11V S Q R Q TG CIN BOT TOP ON SW SWITCH LOGIC - SHDN VOUT INTVCC COUT BG MODE 0.5A OV RUN 0.425V + SLEEP - + IREV - ICMP -+ +- + 2mV 2.7V 0.65V 15% ABOVE REGULATION SENSE+ SENSE- SLOPE COMP + - VOUT /EXTVCC + VIN - EA VFB 1.2V TRACK/SS VOUT/EXTVCC 3.3V/5V PROGRAM - VOUTPRG GATE CONTROL 5.1V LDO EN EN SHDN RST 2(VFB) + 4.7V CC ITH - FOLDBACK 10A CC2 RC TRACK/SS CSS SHDN INTVCC HIGH VOLTAGE CONTROLLER RT PLL/MODE 4 CLK (fOSC) OSCILLATOR CT MODE BANDGAP OT REF UVLO UV CT OSCILLATOR WDI TEMP MONITOR WDO TEMP 2 SD WATCHDOG TIMER STATE MACHINE CT CLOCK LOW VOLTAGE REGULATORS VINA RST 4 PGOOD DELAY 1A POWER STAGE A SWA 1A POWER STAGE B SWB 1A POWER STAGE C SWC 1A POWER STAGE D SWD 1A POWER STAGE E SWE 1A POWER STAGE F SWF 1A POWER STAGE G SWG 1A POWER STAGE H SWH VINB SD REF CLK MODE 4 VINC VINB EN1 FB1 VIND BUCK REGULATOR 1 CONTROL VIND EN2 FB2 VINE BUCK REGULATOR 2 CONTROL VINE EN3 FB3 VINF BUCK REGULATOR 3 CONTROL VING VING EN4 FB4 BUCK REGULATOR 4 CONTROL CONFIGURATION LINES C1 C2 C3 VINH GND (EXPOSED PAD) 33721 BD Rev. A For more information www.analog.com 17 LTC3372 OPERATION The LTC3372 is a single IC that combines a high voltage (HV) buck (step-down) DC/DC switching regulator controller and a total of four configurable low voltage (LV) buck regulators. Main Control Loop of HV Buck Controller The HV controller uses a constant frequency, current mode buck (step-down) architecture. During normal operation, the external top MOSFET is turned on when the clock sets the RS latch, and is turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier, EA. The error amplifier compares an internal 1.2V reference voltage to the feedback voltage generated by an internal resistor divider connected to the VOUT/EXTVCC pin. The divider can be selected to program an output of either 3.3V to 5V. When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current matches the new load current. After the top MOSFET is turned off each cycle, the bottom MOSFET is turned on until either the beginning of the next clock cycle, or the inductor current starts to reverse, as indicated by the reverse current comparator IREV (at light load in pulse-skipping mode or Burst Mode). INTVCC Power Power for the top and bottom MOSFET drivers and some other internal circuitry is derived from the INTVCC pin. When the VOUT/EXTVCC pin is tied to a voltage less than 4.7V, the VIN LDO (low dropout linear regulator) supplies 5.1V from VIN to INTVCC. If VOUT/EXTVCC is taken above 4.7V, the VIN LDO is turned off and an internal PMOS switch connects VOUT/EXTVCC to INTVCC. Using the VOUT/EXTVCC pin allows the INTVCC power to be derived from the high efficiency HV buck regulator output. The top MOSFET driver is biased from the floating bootstrap capacitor, CB, which normally recharges during each cycle through an external diode, DB, when the top MOSFET turns off. If the input voltage, VIN, decreases to a voltage close 18 to VOUT, the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for a short time every tenth cycle to allow CB to recharge, resulting in an effective duty cycle of 98%. Shutdown and Start-Up (RUN, TRACK/SS Pins) It typically takes 1.2ms for the internal bias circuits (including INTVCC) to be ready after the first time either the RUN pin or any of the EN1-4 pins rises above 730mV. During the 1ms internal bias circuit startup time, neither the HV or LV regulators are enabled. The HV controller is enabled when the RUN pin is pulled above 1.2V and the internal bias is enabled. Pulling RUN pin below 1.16V disables the HV controller. The RUN pin has an internal 0.5A current that pulls up the pin to enable the HV controller. Alternatively, the RUN pin may be externally pulled up or driven by logic. The RUN pin can tolerate up to 65V (absolute maximum), so it can be conveniently tied to VIN in an always-on application in which the controller is enabled continuously and never shut down. The RUN pin can also be used as an undervoltage lockout (UVLO) by connecting it to the midpoint of an external resistor divider network of VIN (see Applications Information section). The start-up of the controller's output voltage VOUT is controlled by the voltage on the TRACK/SS pin. When the voltage on the TRACK/SS pin is less than the 1.2V internal reference, the HV controller regulates the VFB voltage to the TRACK/SS pin voltage instead of the 1.2V reference. This allows the TRACK/SS pin to be used to program a soft-start by connecting an external capacitor from the TRACK/SS pin to GND. An internal 10A pull-up current charges this capacitor creating a voltage ramp on the TRACK/SS pin. As the TRACK/SS voltage rises linearly from 0V to 1.2V and beyond, the output voltage VOUT rises smoothly from zero to its final value. Alternatively the TRACK/SS pin can be used to cause the start-up of VOUT to track that of another supply. Typically, this requires connecting to the TRACK/ SS pin an external resistor divider from the other supply to ground (see the Applications Information section). Rev. A For more information www.analog.com LTC3372 OPERATION Output Overvoltage Protection Overvoltage comparators guard against transient overshoots as well as other more serious conditions that may overvoltage the output. When the VOUT/EXTVCC pin voltage rises by more than 7.5% above its regulation set point, the top power MOSFET gate (TG) is turned off and the bottom power MOSFET gate (BG) is turned on until the overvoltage condition is cleared. The SENSE- pin functions as the output voltage sense pin for a secondary +15% overvoltage protection in addition to the +7.5% overvoltage protection at VOUT/EXTVCC pin. When voltage at this pin is over 15% higher than the regulated output voltage set point, the HV controller will turn TG off and BG on. This provides an additional layer of protection when point-of-load (POL) regulation is desired. Power Good Indicator (PGOOD) Pin The PGOOD pin is connected to the open drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD pin low when the VOUT/EXTVCC voltage is outside of the 7.5% window around the regulated level. The PGOOD pin is also pulled low when the RUN pin is low (shut down). When the VOUT/EXTVCC voltage is within the 7.5% window, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6V. Foldback Current Limit When the output voltage falls to less than 70% of its nominal level, foldback current limiting is activated. Foldback progressively lowers the peak current limit as the output drops in a sustained overcurrent or short-circuit condition. Foldback current limiting is disabled during the soft-start interval (as long as the VFB voltage is keeping up with the TRACK/SS voltage). Light Load Current Operation The HV buck controller can be enabled to enter one of the three modes at light load current: (a) high efficiency Burst Mode, (b) forced continuous conduction mode, or (c) pulse-skipping mode operations at light load currents. The LTC3372's PLL/MODE pin selects the light load operation modes for both the HV controller and LV buck regulators. To select Burst Mode operation, tie the PLL/MODE pin to SGND. To select forced continuous mode operation, tie the PLL/MODE pin to INTVCC. When PLL/MODE pin is connected to an external clock, both HV controller and the LV buck regulators are synchronized to the external clock in forced continuous mode operation. To select pulse-skipping mode for the HV controller, tie the PLL/MODE pin to a DC voltage greater than 1.2V but less than INTVCC - 3.3V. The LV buck regulators will operate in Burst Mode operation. When the controller is enabled for Burst Mode operation, the minimum peak current in the inductor is set to approximately 25% of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the error amplifier, EA, will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V, the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. The ITH pin is then disconnected from the output of the EA and parked at 0.450V. In sleep, much of the internal circuitry is turned off, reducing the quiescent currents that the controllers draws. The load current is supplied by the output capacitor. As the output voltage decreases, the EA's output begins to rise. When the output voltage drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. When the controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator, IREV, turns off the bottom external MOSFET just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller operates in discontinuous operation. In forced continuous operation, the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Rev. A For more information www.analog.com 19 LTC3372 OPERATION Burst Mode operation. However, continuous operation has the advantage of lower output voltage ripple and less interference to other circuitry. In forced continuous mode, the output ripple is independent of load current. Clocking the LTC3372 from an external source enables forced continuous mode (see the Programming the Operating Frequency section.) When the PLL/MODE pin is connected for pulse-skipping mode, the HV controller operates in PWM pulse-skipping mode at light loads. In this mode, constant frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator, ICMP, may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. It typically takes 1ms for the internal bias circuits (including INTVCC) to be ready after the first time RUN or any EN pin rises above 0.73V. All regulators are disabled during internal circuit start-up time. When a LV regulator is enabled there is an additional 150s delay before the soft start ramp begins. All LV regulators have soft start and forward and reverse current limiting to control inrush current during start-up and to provide short-circuit protection in normal operation. The LV buck switching regulators are phased in 90 steps to reduce noise and input ripple. The phase step determines the fixed edge of the switching sequence, which is when the PMOS turns on. The PMOS off (NMOS on) phase is subject to the duty cycle demanded by the regulator. Buck 1 is set to 0, Buck 2 is set to 90, Buck 3 is set to 270, and Buck 4 is set to 180. In shutdown all SW nodes are high impedance. The buck regulator enable pins may be tied to VOUT voltages through a resistor divider, to program power-up sequencing. LV Buck Regulators with Combined Power Stages LOW VOLTAGE REGULATORS Low Voltage Buck Switching Regulator The LTC3372 contains eight low voltage (LV) monolithic 1A synchronous buck switching power stages. Each power stage contains an integrated PMOS top-side switch and a NMOS bottom-side switch. The eight power stages are controlled by up to four constant frequency peak current mode controllers. All of the switching regulators are internally compensated and need only external feedback resistors to set their output voltages. Each LV buck switching regulator can operate with an independent input voltage and has its own FB and EN pins to maximize flexibility. The enable pins have two different enable thresholds that depend on the operating state of the other LV regulators. When all of the LV regulators are disabled, the EN pin threshold is 0.73V . Once any LV regulator is enabled, the EN pin thresholds of the remaining LV regulators are set to a precision internalreference-based 400mV. This precision EN threshold may 20 be used to provide event based sequencing via feedback from other previously enabled regulators. Up to four adjacent LV buck regulators may be combined in a master-slave configuration by setting the configuration via the C1, C2, and C3 pins. These pins should either be tied to ground or pin strapped to INTVCC in accordance with the desired configuration code (Table 1). Any combined SW pins must be tied together, as must any of the combined VIN pins. EN1 and FB1 are utilized by Buck 1, EN2 and FB2 by Buck 2, EN3 and FB3 by Buck 3, and EN4 and FB4 by Buck 4. If any buck is not used or is not available in the desired configuration, then the associated FB and EN pins must be tied to ground. Any available combination of 2, 3, or 4 adjacent buck regulators serves to provide up to either 2A, 3A, or 4A of average output load current. For example, code 110 (C3C2C1) configures Buck 1 to operate as a 4A regulator through VINA-H /SWA-H pairs A, B, C, and D, while Buck 2 is disabled, Buck 3 operates as a 1A regulator through VINA-H /SWA-H pair E, and Buck 4 operates as a 3A regulator through VINA-H /SWA-H pairs F, G, and H. Rev. A For more information www.analog.com LTC3372 OPERATION Table 1. Master Slave Program Combinations (Each Letter Corresponds to a Low Voltage Power Stage) PROGRAM CODE C3C2C1 BUCK 1 BUCK 2 BUCK 3 BUCK 4 000 AB CD EF GH 001 ABC D EF GH 010 ABC D E FGH 011 ABCH D E FG 100 ABC DE Not Used FGH 101 ABCD Not Used EF GH 110 ABCD Not Used E FGH 111 ABCD Not Used Not Used EFGH Power Failure Reporting via RST Pin Power failure conditions of all LV buck regulators are reported by the single RST pin. Each LV regulator has an internal power good signal. If LV Buck 1 output voltage falls below 98%, or any of the Buck 2-4 outputs falls below 95%, of its programmed value, or if any LV regulator's output rises above 107.5% of its programmed value, its internal power good signal is pulled low. If any internal power good signal stays low for greater than 100s, then the RST pin is pulled low. The RST low signal indicates to a microprocessor that a power failure fault has occurred. The 100s filter time prevents a false fault indication low due to a output/load transient. The internal power good comparators have hysteresis, so the regulated output voltage of an enabled regulator has to move back into the power good window by more than the hysteresis for its power good signal to transition high. Once all enabled LV regulator outputs are power good for 202ms (typical, CT = 10nF), the RST output goes high impedance (pulled high by external resistor/current). If all LV buck regulators are disabled, RST pulls low. Temperature Monitoring and Overtemperature Protection To prevent thermal damage to the IC and its surrounding components, the LV regulators have an overtemperature (OT) function. When the LTC3372 die temperature reaches 170C (typical) all LV buck switching regulators are shut down and remain in shutdown until the die temperature falls to 160C (typical). The temperature may be read back by the user by sampling the TEMP pin analog voltage. The temperature, T, indicated by the TEMP pin voltage is given by: V - 45mV T = TEMP * 1C 7mV To reduce quiescent current (IQ), if all the LV buck regulators are shut down, the temperature monitor also shuts down and the TEMP pin becomes high impedance. The temperature monitor can be disabled by tying the TEMP pin to INTVCC to save IQ. Programming the Operating Frequency Selection of the operating frequency is a trade-off between efficiency and component size. High frequency operation allows the use of smaller inductor and capacitor values. Operation at lower frequencies improves efficiency by reducing internal gate charge losses but requires larger inductance values and/or capacitance to maintain low output voltage ripple. The frequency of the internal oscillator (system clock) is determined by an external resistor that is connected between the RT pin and ground. The operating frequency can be calculated using the following equation: fOSC = 8 * 10 11 * Hz RT The oscillator is designed to function with operating frequencies between 1MHz and 3MHz, it has safety clamps that prevent the oscillator from running faster than 4MHz (typical) or slower than 250kHz (typical). Tying the RT pin to INTVCC sets the oscillator to the default internal operating frequency of 2MHz (typical). The internal oscillator can be synchronized through an internal PLL circuit to an external frequency by applying a square wave clock signal to the PLL/MODE pin. During synchronization, the top MOSFET turn-on of LV buck regulator 1 is phase-locked to the rising edge of the external frequency source. All other LV regulators are locked to the appropriate phase of the external frequency source. Rev. A For more information www.analog.com 21 LTC3372 OPERATION The synchronization frequency range is 1MHz to 3MHz. A synchronization signal on the PLL/MODE pin will force all low voltage (LV) active buck switching regulators to operate in forced continuous mode PWM. The LV regulators switch directly off the internal oscillator in 90-degree phase increments. The LTC3372 HV controller switches at one-sixth (1/6) of the internal oscillator frequency with a range of between 166kHz to 500kHz. Windowed Watchdog Timer A standard watchdog function is used to ensure that the system is in a valid state by continuously monitoring the microprocessor's activity. The microprocessor must toggle the logic state of the WDI pin periodically in order to clear the watchdog timer. The WDI pin reset is read only on a WDI falling edge, such that a single reset signal may be asserted by pulsing the WDI pin for a time greater than the minimum pulse width. If timeout occurs, a WDO low is asserted for the reset timeout period, issuing a system reset. Once the reset timeout completes, WDO is released to go high and the watchdog timer starts again. During power-up, the watchdog timer initiates in the timeout state with WDO asserted low. As soon as the reset timer times out, WDO goes high and the watchdog timer is started. A windowed watchdog function is implemented by adding a lower boundary condition to the standard watchdog function. If the WDI input receives a falling edge prior to the watchdog lower boundary, the part considers this a watchdog failure, and asserts WDO low (releasing again after the reset timeout period as described above). This will again be followed by another lower boundary time period. The watchdog timer shuts down when RUN and EN1-4 are off (all HV and LV regulators are shut down). Tying the CT pin to INTVCC disables the watchdog timer regardless of the RUN and EN1-4 pins (HV and LV regulators either on or off). Choosing the CT Capacitor The watchdog timeout period is adjustable and can be optimized for software execution. The watchdog timeout period is adjusted by connecting a capacitor between CT and ground. Given a specified watchdog timeout period, the capacitor is determined by: CT = tWDO * 49.39 [nF/s] For example, using a standard capacitor value of 10nF gives a 202ms watchdog timeout period. Further, the other watchdog timing periods scale with tWDO. The watchdog lower boundary time (tWDL) scales as precisely 1/4 of tWDO, the watchdog upper boundary time following the previous WDI pulse scales as eight times that of tWDO, and the watchdog upper boundary time following a watchdog timeout scales as 64 times that of tWDO. Finally the RST assertion delay will scale to the same time as tWDO. These timing periods are illustrated in Figure 1. Each WDO low period is equal to the time period t2-t1 (202ms for a 10nF CT capacitor, typical). If a WDI falling edge occurs before the watchdog lower boundary, indicated by t3-t2 (50.6ms for a 10nF CT capacitor, typical), then another watchdog timeout period occurs. If a WDI falling edge occurs after the watchdog lower boundary (t4), then the watchdog counter resets, beginning with another watchdog lower boundary period. In the case where a WDI low transition is not detected by the specified time another watchdog timeout period is initiated. This time is indicated by t5-t4 (1.62s for a 10nF CT capacitor, typical). If a WDI low transition is not detected within the specified time following a watchdog timeout period, then another watchdog timeout period is initiated. This time is indicated by t7-t6 (12.9s for a 10nF CT capacitor, typical). WDO WDI 3372 F01 t1 t2 t3 t4 t5 t6 t7 Figure 1. WDO Timing Parameters 22 Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller HIGH VOLTAGE BUCK CONTROLLER The Typical Application on the first page is a basic application circuit. The HV controller inductor current sensing can be configured to use either DCR (inductor resistance) or a low value sense resistor. The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption and accuracy. DCR sensing has become popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs. Finally, input and output capacitors are selected. programmed current limit unpredictable. If inductor DCR sensing is used (Figure 3b), resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. TO SENSE FILTER, NEXT TO THE CONTROLLER 3372 F02 INDUCTOR OR RSENSE Figure 2. Sense Lines Placement with Inductor or Sense Resistor VIN INTVCC VIN BOOST TG Current Sense Pins (SENSE+ and SENSE-) RSENSE SW The SENSE+ and SENSE- pins are the inputs to the current comparators. The common mode voltage range on these pins is 0V to 6V (abs max), allowing margin for tolerances and transients for the HV regulator's regulated 5V or 3.3V output. The SENSE+ pin is high impedance over the full common mode range, drawing at most 1A. This high impedance allows the current comparators to be used in inductor DCR sensing. Connect the SENSE- pin directly to the sense point at the VOUT side of the inductor (in DCR sensing) or the current sense resistor (RSENSE), without adding any resistor in series. The impedance of the SENSE- pin changes depending on its voltage. When SENSE- is less than INTVCC - 0.5V, a small current of less than 1A flows out of the pin. As SENSE- approaches INTVCC, the current transitions higher to close to 1mA. Filter components mutual to the sense lines should be placed close to the IC, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 2). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the COUT LTC3372 VOUT BG SENSE+ SENSE- R1* C1* PLACE CAPACITOR NEAR SENSE PINS GND 3372 F03a *R1 AND C1 ARE OPTIONAL (3a) Using a Resistor to Sense Current VIN INTVCC VIN BOOST INDUCTOR TG L SW LTC3372 DCR VOUT BG R1 SENSE+ C1* R2 SENSE- GND *PLACE C1 NEAR SENSE PINS (R1||R2) * C1 = L DCR RSENSE(EQ) = DCR R2 R1 + R2 3372 F03b (3b) Using the Inductor DCR to Sense Current Figure 3. Current Sensing Methods Rev. A For more information www.analog.com 23 LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 3a. RSENSE is chosen based on the required output current. This LTC3372's current comparator has a fixed maximum current limit threshold of 75mV (typical). The current comparator threshold voltage sets the peak of the inductor current, yielding a maximum average output current, IMAX, equal to the peak value less half the peak-to-peak ripple current, IL. To calculate the sense resistor value, use the equation: R SENSE = VSENSE(MAX) IMAX + IL 2 Using the inductor ripple current value from the Inductor Value Calculation section, the target sense resistor value is: R SENSE(EQUIV) = To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value (68mV) for the Maximum Current Sense Threshold (VSENSE(MAX)) in the Electrical Characteristics table. When using the controller in very low dropout conditions, the maximum output current level will be reduced due to the internal compensation required to meet stability criterion for buck regulators operating at greater than 50% duty factor. The maximum current sense threshold vs duty cycle curve is provided in the Typical Performance Characteristics section to estimate this reduction in peak inductor current depending upon the operating duty factor. Inductor DCR Current Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3372's HV controller is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 3b. The DCR of the inductor represents the small amount of DC resistance of the copper wire, which can be less than 1m for today's low value, high current inductors. In a high current application requiring such an inductor, power loss through a sense resistor would cost several points of efficiency compared to inductor DCR sensing. 24 If the external (R1||R2) * C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers' data sheets for detailed information. VSENSE(MAX) IMAX + IL 2 To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value (68mV) for the Maximum Current Sense Threshold (VSENSE(MAX)) in the Electrical Characteristics table. Next, determine the DCR of the inductor. When provided, use the manufacturer's maximum value, usually given at 20C. Increase this value to account for the temperature coefficient of copper resistance, which is approximately 0.4%/C. A conservative value for TL(MAX) is 100C. To scale the maximum inductor DCR to the desired sense resistor value, use the divider ratio (RD): RD = R SENSE(EQUIV) DCRMAX at TL(MAX) C1 is usually selected to be in the range of 0.1F to 0.47F. This forces R1 || R2 to around 2k, reducing error that might have been caused by the SENSE+ pin's 1A current. The equivalent resistance R1 || R2 is scaled to the room temperature inductance and maximum DCR: R1|| R2 = L (DCR at 20C) * C1 Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller The sense resistor values are: R1= R1|| R2 RD ; R2 = R1* RD 1- RD The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: P LOSS R1= (VIN(MAX) - VOUT ) * VOUT R1 Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET switching and gate charge losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current, IL, decreases with higher inductance or higher frequency and increases with higher VIN: IL = V VOUT 1- OUT VIN (f)(L) 1 Accepting larger values of IL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is IL = 0.3(IMAX). The maximum IL occurs at the maximum input voltage. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 25% of the current limit determined by RSENSE. Lower inductor values (higher IL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance value selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred for high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates hard, which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET and Schottky Diode (Optional) Selection Two external power MOSFETs must be selected for the HV controller: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5.1V during start-up (see VOUT Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. Pay close attention to the BVDSS specification for the MOSFETs as well. Selection criteria for the power MOSFETs include the onresistance, RDS(ON), Miller capacitance, CMILLER, input Rev. A For more information www.analog.com 25 LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers' data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT VIN Synchronous Switch Duty Cycle = VIN - VOUT VIN The MOSFET power dissipations at maximum output current are given by: The term (1+ ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but = 0.005/C can be used as an approximation for low voltage MOSFETs. A Schottky diode can be placed in parallel with the bottom MOSFET to conduct during the dead-time between the conduction of the two power MOSFETs. This prevents the body diode of the bottom MOSFET from turning on, storing charge during the dead-time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high VIN. A 1A to 3A Schottky is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. Another consideration is the losses due to the gate charge of the MOSFETs. Each cycle, the bottom FET gate driver draws a pulse of current from the INTVCC pin when turning on the bottom FET gate. Another pulse of current is drawn by the boost capacitor as the bottom FET turns on. This energy is used by the floating high side driver to turn on the top MOSFET. The INTVCC decoupling capacitor smooths the current flowing through the LDO. The resulting DC current can be estimated as: V PMAIN = OUT (IMAX )2 (1+ )RDS(ON) + VIN I (VIN )2 MAX (RDR )(CMILLER ) * 2 1 1 + (f) VINTVCC - VTHMIN VTHMIN V - VOUT (IMAX )2 (1+ ) RDS(ON) PSYNC = IN VIN IGQ = f(QGT + QGB) where is the temperature dependency of RDS(ON) and RDR (approximately 2) is the effective driver resistance at the MOSFET's Miller threshold voltage. VTHMIN is the typical MOSFET minimum threshold voltage. Both MOSFETs have I2R losses while the topside N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For VIN < 20V the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during 26 a short-circuit when the synchronous switch is on close to 100% of the period. The LDO losses will then become: PLDO = (VIN - VINTVCC) * IGQ To avoid the LDO losses, program VOUT for 5V with the VOUTPRG pin. With this setting, the INTVCC LDO is shut down and the INTVCC pin is tied to VOUT with an internal switch. This will provide significant power loss reductions for high input voltages. The losses in the gate driver are also affected by the MOSFET gate charge. A conservative estimate of the these losses is: PGATE_DRIVE = IGQ * VINTVCC Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller CIN and COUT Selection Setting Output Voltage (HV Controller) The selection of CIN is usually based off the worst-case RMS input current. The highest (VOUT)(IOUT) product needs to be used in the formula to determine the maximum RMS capacitor current requirement. The HV controller output voltage is set by the VOUTPRG pin through an internal resistor voltage divider. When the VOUTPRG pin is tied to INTVCC, the output voltage is regulated to 5V. When tied to ground, the output voltage is regulated to 3.3V. In continuous mode, the source current of the top MOSFET is a square wave of duty cycle (VOUT)/(VIN). To prevent large voltage transients, a low ESR capacitor sized for the maximum RMS current must be used. The maximum RMS capacitor current is given by: I 1/2 CIN Required IRMS MAX [(VOUT )(VIN - VOUT )] VIN This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than size or height requirements in the design. Due to the high operating frequency, ceramic capacitors can also be used for CIN. Always consult the manufacturer if there is any question. A small (0.1F to 1F) bypass capacitor between the chip VIN pin and ground, placed close to the IC, is also suggested. A small (<10) resistor placed between CIN (C1) and the VIN pin provides further isolation. The selection of COUT is driven by the effective series resistance (ESR). Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering. The output ripple (VOUT) is approximated by: RUN Pin The HV controller is enabled using the RUN pin. It has a rising threshold of 1.2V with 50mV of hysteresis. Pulling the RUN pin below 1.15V shuts down the main control loop. Pulling it below 0.7V disables the controller and most internal circuits, including the INTVCC LDOs. Releasing the RUN pin allows a 0.5A internal current to pull up the pin to enable the controller. The RUN pin may be externally pulled up to up to 60V (65V Abs Max). The RUN pin can be implemented as a UVLO by connecting it to the output of an external resistor divider network off VIN, as shown in Figure 4. The rising and falling UVLO thresholds are calculated using the RUN pin thresholds: R VUVLO(RISING) = 1.2V 1+ B RA R VUVLO(FALLING) = 1.15V 1+ B RA The resistor values should be carefully chosen such that the absolute maximum ratings of the RUN pin do not get violated over the entire VIN voltage range. VIN LTC3372 1 VOUT IL ESR + 8 * f * COUT RB RUN RA where f is the operating frequency, COUT is the output capacitance and IL is the ripple current in the inductor. The output ripple is highest at maximum input voltage since IL increases with input voltage. 3372 F04 Figure 4. Using the RUN Pin as a UVLO Rev. A For more information www.analog.com 27 LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller Tracking and Soft-Start (TRACK/SS Pin) Soft-start is enabled by simply connecting a capacitor from the TRACK/SS pin to ground, as shown in Figure 5. An internal 10A current source charges the capacitor, providing a linear ramping voltage at the TRACK/SS pin. The HV controller will regulate the VFB (and hence VOUT) according to the voltage on the TRACK/SS pin, allowing VOUT/EXTVCC to rise smoothly from 0V to its final regulated value. The total soft-start time will be approximately: VOUT = 3372 F05 Figure 5. Using the TRACK/SS Pin to Program Soft-Start VX(MASTER) VOUT(SLAVE) (6a) Coincident Tracking 10A VX(MASTER) VOUT(SLAVE) R + R TRACKB * TRACKA R TRACKA VOUT(REG) 1.2V 3372 F06b TIME VOUT(REG) is the programmed output regulation voltage. If the VOUTPRG pin it tied to INTVCC pin, VOUT(REG) = 5V. If the VOUTPRG pin is tied to ground, VOUT(REG) = 3.3V. (6b) Ratiometric Tracking Figure 6. Two Different Modes of Output Voltage Tracking VOUT/EXTVCC INTVCC Regulation INTVCC powers the gate drivers and much of the internal circuitry. Power to the INTVCC pin is supplied either from the VIN pin through an internal low dropout linear regulator (LDO), or from the VOUT/EXTVCC pin through an internal switch, depending on the voltage at VOUT/EXTVCC. The VIN LDO regulates INTVCC to 5.1V. The INTVCC can supply a peak current of at least 50mA and must be bypassed to ground with a minimum of 4.7F ceramic capacitor. Good 28 3372 F06a TIME 1.2V Alternatively, the TRACK/SS pin can be used to track another supply during start-up, as shown qualitatively in Figures 6a and 6b. To do this, a resistor divider should be connected from the master supply (VX) to the TRACK/SS pin of the slave supply (VOUT/EXTVCC) as shown in Figure 7. During start-up VOUT/EXTVCC will track VX according to the ratio set by the resistor divider: VX SGND OUTPUT VOLTAGE tSS = CSS * CSS OUTPUT VOLTAGE The start-up of VOUT is controlled by the voltage on the TRACK/SS pin. When the voltage on the TRACK/SS pin is less than the internal 1.2V reference, it regulates the internal VFB voltage to the voltage on the TRACK/SS pin instead of 1.2V. The TRACK/SS pin can be used to program an external soft-start function or to allow VOUT to track another supply during start-up. LTC3372 TRACK/SS VOUT/EXTVCC Vx LTC3372 RTRACKB TRACK/SS RTRACKA 3372 F07 Figure 7. Using the TRACK/SS Pin for Tracking Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to prevent interaction between the channels. The INTVCC load current (IINTVCC) is dominated by the gate charge current and may be supplied by either the VIN LDO or the VOUT/EXTVCC pin. The gate charge current is dependent on operating frequency and NMOS size as discussed in the Efficiency Considerations section. When the VOUT/EXTVCC regulation is set to 3.3V, the VIN LDO is always enabled as the voltage on the VOUT/EXTVCC pin is never above the 4.7V threshold. Power dissipation for the IC in this case is highest and is equal to VIN * IINTVCC. High input voltage applications in which large power MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the IC to be exceeded. For example, a 30mA INTVCC current from a 48V input supply will result in a junction temperature (TJ) increase (rise) of: TJ = (30mA)(48V)(34C/W for QFN) = 48C The power dissipation due to IINTVCC from VIN should be checked at the maximum VIN of the application operating in forced continuous mode. When the VOUT regulation is set to 5V and VOUT rises above 4.7V, INTVCC is connected to VOUT through an internal switch. Significant efficiency and thermal gains can be realized by powering INTVCC from the output, since the input supply current resulting from INTVCC current is scaled by a factor of (VOUT/VIN)/(efficiency). In this case, power dissipation in the LTC3372 due to the INTVCC current is VINTVCC * IINTVCC, and the junction temperature (TJ) increase (rise) of: TJ = (30mA)(5V)(34C/W for QFN) = 5C The LTC3372 junction temperature (TJ) can be estimated from ambient temperature (TA) and total power dissipation (PD) using the equations given in Note 2 of the Electrical Characteristics. To prevent the maximum junction temperature from being exceeded, all power dissipations from the HV controller's INTVCC current and the LV buck power stages must be considered. Topside MOSFET Driver Supply (CB, DB) An external bootstrap capacitor, CB, connected to the BOOST pin supplies the gate drive voltage for the topside MOSFET. Capacitor CB in the Block Diagram is charged though external diode DB from INTVCC when the SW pin is low. When the topside MOSFET is to be turned on, the driver places the CB voltage across the gate-source of the MOSFET. This enhances the top MOSFET switch and turns it on. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC. The value of the boost capacitor, CB, needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). Fault Conditions: Current Limit and Current Foldback The HV controller includes current foldback to help limit load current when the output is shorted to ground. If the output voltage falls below 70% of its nominal output level, then the maximum sense voltage is progressively lowered from 100% to 45% of its maximum selected value. Under short-circuit conditions with very low duty cycles, cycle skipping will begin in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power. The short-circuit ripple current is determined by the minimum on-time, tON(MIN) (see Electrical Characteristics), the input voltage and inductor value: V IL(SC) = tON(MIN) IN L The resulting average short-circuit current is: 1 ISC = 45% * ILIM(MAX) - IL(SC) 2 Fault Conditions: Overvoltage Protection (Crowbar) The overvoltage crowbar is designed to blow a system input fuse when the output voltage of the regulator rises much higher than nominal levels. The crowbar causes huge currents to flow, that blow the fuse to protect against a shorted top MOSFET if the short occurs while the controller is operating. Rev. A For more information www.analog.com 29 LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller Both the VOUT and SENSE- pins are monitored for overvoltage conditions. An overvoltage condition is detected when either pin is 7.5% above the nominal output voltage. When this condition is sensed, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. The bottom MOSFET remains on continuously for as long as the overvoltage condition persists; if VOUT returns to a safe level, normal operation automatically resumes. A shorted top MOSFET will result in a high current condition which will open the system fuse. The switching regulator will regulate properly with a leaky top MOSFET by altering the duty cycle to accommodate the leakage. Minimum On-Time Considerations The minimum on-time, tON(MIN), is the smallest time duration that the HV controller is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: V tON(MIN) < OUT VIN (f) If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. The minimum on-time of top FET is typically 60ns. However, as the peak sense voltage decreases the minimum on-time gradually increases. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would 30 produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in HV regulator: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) topside MOSFET transition losses. 1. The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss. 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. In applications when VOUT/EXTVCC is set to 5V, INTVCC is supplied through VOUT/EXTVCC. This scales the VIN current required for the driver and control circuits by a factor of (Duty Cycle)/(Efficiency). For example, in a 20V to 5V application, 10mA of INTVCC current results in approximately 2.5mA of VIN current. This reduces the midcurrent loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 3. I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor and input and output capacitor ESR. In continuous mode the average output current flows through L and RSENSE, but is chopped between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller losses. For example, if each RDS(ON) = 30m, RL = 50m, RSENSE= 10m and RESR = 40m (sum of both input and output capacitance losses), then the total resistance is 130m. This results in losses ranging from 3% to 13% as the output current increases from 1A to 5A for a 5V output, or a 4% to 20% loss for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 4. Transition losses apply only to the topside MOSFET(s), and become significant only when operating at high input voltages (typically 15V or greater). Transition losses can be estimated from: Transition Loss = (1.7) * VIN * 2 * IO(MAX) * CRSS * f Other hidden losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these system level losses during the design phase. The internal battery and fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and very low ESR at the switching frequency. A 25W supply will typically require a minimum of 20F to 40F of capacitance having a maximum of 20m to 50m of ESR. Other losses including body diode conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ILOAD (ESR), where ESR is the effective series resistance of COUT. ILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTILOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC coupled and AC filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components in Typical Applications will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1s to 10s will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a power MOSFET directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. Rev. A For more information www.analog.com 31 LTC3372 APPLICATIONS INFORMATION High Voltage Buck Controller A second, more severe transient is caused by switching in loads with large (>1F) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT/EXTVCC. No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 * CLOAD. Thus a 10F capacitor would require a 250s rise time, limiting the charging current to about 200mA. Rounding down to the next standard value yields a sense resistor value of 5m. Design Example At the nominal input voltage of 12V with T(estimated) = 50C, the losses become: As a design example, assume VIN = 12V (nominal), VIN = 60V (max) for transient voltages, VOUT = 3.3V, IMAX = 10A, VSENSE(MAX) = 75mV and f = 333kHz. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the RT pin to INTVCC (for better frequency accuracy over temperature, use an external RT = 400k to ground), generating 333kHz operation for LTC3372's HV controller (1/6 of fOSC at 2MHz). The maximum ripple current is: VOUT VOUT IL = 1- (f)(L) VIN(MAX) tON(MIN) = VIN(MAX)(f) = 3.3V 60V(333kHz) = 165ns The equivalent RSENSE resistor value can be calculated by using the minimum value for the maximum current sense threshold (68mV): R SENSE 32 68mV 12.1A 5.6m Top: RJK0651DPB RDS(ON) = 0.018, QG = 15nC, CMILLER = 148pF, VTHMIN = 1.2V, VDSS = 60V Bottom: RJK0652DPB RDS(ON) = 0.009, QG = 29nC, VDSS = 60V PMAIN = 3.3V 12V (10A)2 [1 + (0.005)(50C - 25C)](0.018) + (12V)2 10 A 2 (2 )(148pF) * 1 1 + (333kHz) 5.1V - 1.2V 1.2V = 557mW + 77mW = 643mW PSYNC = A 2.2H inductor will produce 43% ripple current which is sufficiently close. The peak inductor current will be the maximum DC value plus one half the ripple current, or 12.1A. Increasing the ripple current will also help ensure that the minimum on-time of 60ns is not violated. The minimum on-time occurs at maximum VIN: VOUT For a 3.3V/10A 333kHz converter operating with a nominal 12V input and a 60V surge rating, a reasonable MOSFET selection is: 12V - 3.3V (10A)2 * 12V [1+ (0.005)(50C - 25C)] (0.009) = 734mW Other losses include the gate drive and INTVCC LDO losses. These can be estimated from the gate charge and switching frequency: IGQ = 333kHz (15nC + 29nC) = 14.7mA PLDO = (12V - 5.1V) 14.7mA = 101mW PGATE_DRIVE = 5.1V * 14.7mA PGATE_DRIVE = 75mW Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION Low Voltage Buck Regulators With the input voltage at a sustained 60V and full load on the output, the estimated power losses in the main FET will be 2.0W and the LDO losses inside the chip will be 0.8W. Airflow will likely be required. A lower switching frequency will reduce these losses and setting VOUT to 5V will avoid the LDO losses. A short-circuit to ground will result in a folded back current of: ISC = 0.45(75mV) 0.005 1 60ns(22V) - = 6.6A 2 2.2H with a maximum value of RDS(ON) and = (0.005/C)(25C) = 0.125. The resulting power dissipated in the bottom MOSFET is: PSYNC = (6.6A)2 (1.125)(0.009) = 441mW which is less than under full-load conditions. CIN is chosen for an RMS current rating of at least 5A at temperature assuming only this channel is on. COUT is chosen with an ESR of 0.01 for low output ripple. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: regulator transient response may improve with an optional capacitor, CFF, that helps cancel the pole created by the feedback resistors and the input capacitance of the FB pin. Experimentation with capacitor values between 2.2pF and 22pF may improve transient response. Input and Output Decoupling Capacitor Selection The LTC3372 buck regulators have individual input supply pins for each buck power stage. Each of these pins must be decoupled with low ESR capacitors to GND. These capacitors must be placed as close to the pins as possible. Ceramic dielectric capacitors are a good compromise between high dielectric constant and stability versus temperature and DC bias. Note that the capacitance of a capacitor deteriorates at higher DC bias. It is important to consult manufacturer data sheets and obtain the true capacitance of a capacitor at the DC bias voltage that it will be operated at. For this reason, avoid the use of Y5V dielectric capacitors. The X5R/X7R dielectric capacitors offer good overall performance. LOW VOLTAGE BUCK REGULATORS Each low voltage input power supply voltage VIN,A-H Pins 5, 8, 9, 12, 25, 28, 29 and 32 all need to be de-coupled with at least 10F capacitors. If power stages are combined the supplies should be shorted with as short of a trace as possible. Additionally, all LV buck regulator outputs should be bypassed with a capacitor to ground of at least 22F for 1A, 47F for 2A, 68F for 3A and 100F for 4A configurations. Output Voltage and Feedback Network Combined Buck Power Stages The output voltage of each LV buck switching regulators is programmed by a resistor divider connected from the switching regulator's output to its feedback pin and is given by VOUT = VFB(1 + R2/R1) as shown in Figure 8. Typical values for R1 range from 40k to 1M. The buck The LTC3372 has eight power stages that can handle average load currents of 1A each. These power stages may be combined in any one of eight possible combinations, via the C1, C2, and C3 pins (see Table 1). Table 3, Table 4, and Table 5 show recommended inductors for the combined power stage configurations. VORIPPLE = RESR(IL) = 0.1(4.3A) = 43mVP-P VOUT/EXTVCC LV BUCK SWITCHING REGULATOR CFF R2 FBn R1 + COUT 3372 F08 OPTIONAL For a 2A combined buck regulator, the input supply should be de-coupled with a 22F capacitor while the output should be de-coupled with a 47F capacitor. Similarly, for 3A and 4A configurations the input and output capacitance must be scaled up to account for the increased load. Figure 8. Feedback Components Rev. A For more information www.analog.com 33 LTC3372 APPLICATIONS INFORMATION Low Voltage Buck Regulators Table 2. Recommended Inductors for 1A Buck Regulators fOSC 1MHz 2MHz 3MHz PART NUMBER L (H) MAX IDC (A) MAX DCR (m) SIZE IN mm (L x W x H) MANUFACTURER XFL4020-472ME 4.7 2.7 57.4 4 x 4 x 2.1 74408943047 4.7 2.2 52 4.8 x 4.8 x 3.8 XFL4020-222ME 2.2 3.7 23.5 4 x 4 x 2.1 DFE252012P-2R2M 2.2 2.2 84 2.5 x 2.0 x 1.2 Toko IHLP1212BZER2R2M-11 2.2 3 46 3 x 3.65 x 2.0 Vishay 74438336015 1.5 3.7 39 3x3x2 DFE252012F-1R5M 1.5 2.7 58 2.5 x 2 x1.2 CoilCraft Wurth Elektronik CoilCraft Wurth Elektronik Toko Table 3. Recommended Inductors for 2A Buck Regulators fOSC 1MHz 2MHz 3MHz PART NUMBER L (H) MAX IDC (A) MAX DCR (m) SIZE IN mm (L x W x H) MANUFACTURER XEL4020-222ME 2.2 5.5 38.7 4 x 4 x 2.1 74438356022 2.2 4.7 35 4.1 x 4.1 x 2.1 XFL4020-102ME 1 5.4 11.9 4 x 4 x 2.1 IHLP1212BZER1R0M-11 1 4.5 24 3 x 3.65 x 2.0 Vishay SPM4020T-1R0M-LR 1 5.6 28.1 4.1 x 4.4 x 2 TDK 744383360068 0.68 4.5 27 3x3x2 IHLP1212AEERR68M-11 0.68 5.4 22 3 x 3.65 x 1.5 CoilCraft Wurth Elektronik CoilCraft Wurth Elektronik Vishay Table 4. Recommended Inductors for 3A Buck Regulators fOSC 1MHz 2MHz 3MHz PART NUMBER L (H) MAX IDC (A) MAX DCR (m) XEL4020-152ME 1.5 7.4 23.6 SIZE IN mm (L x W x H) MANUFACTURER 4 x 4 x 2.1 IHLP2020CZER1R5M11 1.5 7 18.5 5.18 x 5.49 x 3 XEL4020-821ME 0.82 10.2 13 4x4x2 FDV0530-H-R75M 0.75 9.7 7.6 6.2 x 5.8 x 3 744383560068 0.68 8.2 9 4.1 x 4.1 x 2.1 FDSD0420D-R47M 0.47 6.8 18 4.2 x 4.2 x 2 Toko IHLP1212AEERR47M-11 0.47 6.7 15 3 x 3.65 x 1.5 Vishay CoilCraft Vishay CoilCraft Toko Wurth Elektronik Table 5. Recommended Inductors for 4A Buck Regulators fOSC 1MHz 2MHz 3MHz 34 PART NUMBER L (H) MAX IDC (A) MAX DCR (m) XEL4020-102ME 1 9 14.6 4 x 4 x 2.1 744316100 SIZE IN mm (L x W x H) MANUFACTURER CoilCraft 1 11.5 5.225 5.3 x 5.5 x 4.0 XEL4020-561ME 0.56 11.3 8.8 4 x 4 x 2.1 Wurth Elektronik FDV0530-H-R56M 0.56 11.1 6.3 6.2 x 5.8 x 3 Toko SPM4020T-R47M-LR 0.47 8.7 11.8 4.1 x 4.4 x 2 TDK XEL4014-331ME 0.33 9 12 4 x 4 x 1.4 744383560033 0.33 9.6 7.2 4.1 x 4.1 x 2.1 CoilCraft CoilCraft Wurth Elektronik Rev. A For more information www.analog.com LTC3372 APPLICATIONS INFORMATION Efficiency can be increased by combining more power stages than are required to meet output current requirements. Conduction loss will decrease by adding power stages. The overall efficiency will improve provided the switching loss of the added power stage does not exceed the reduction in conduction loss. For example, a buck running at 900mA load may have a higher efficiency when two power stages are combined to make a 2A buck. In this example, the 900mA load is closer to the peak efficiency power of the 2A buck this it is for a 1A buck. In addition to efficiency concerns, combining additional power stages provides increased margin and transient capability. It is therefore a good idea to explore combining any unused power stages with active bucks in any given application. Otherwise, any unused buck regulator should have it's FB and EN pins tied to ground. The VIN pin may be tied to ground and the SW pin can float. PRINTED CIRCUIT BOARD PCB LAYOUT CONSIDERATIONS PCB Layout Considerations for HV Regulator 1. The path formed by the top N-channel MOSFET, the bottom N-channel MOSFET, and the CINTVCC capacitor should have short leads and (PCB) trace lengths. The output capacitor (-) terminals should be connected as close as possible to the (-) terminals of the input capacitor by placing the capacitor and kept away from the loop described above. For proper operation of the gate drivers, the BG and TG traces should maintain low impedance. The length of the BG and TG traces should be 1.0" or less and the number of via should be kept minimum. 2. Kelvin connect the VOUT/EXTVCC pin directly to the (+) terminal of COUT, or where the regulation needs to be. The connection should not be along the high current input feeds from the input capacitor(s). 3. Route the SENSE- and SENSE+ signals together with minimum PCB trace spacing. The filter capacitor between SENSE+ and SENSE- should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the current sense resistor. Don't connect the current sensing leads backwards! The output voltage may still be maintained but the current mode control will not be realized. 4. Place the INTVCC decoupling capacitor close to the IC, between the INTVCC pin and power ground plane. This capacitor carries the MOSFET drivers' current peaks. A ceramic capacitor placed immediately next to the INTVCC pin can help improve noise performance substantially. 5. Kelvin connect the return of the ITH network to an isolated shape (ground copper "island") tied to the GND pad of the IC (refer to the ground copper "island(s)" discussed in the Ground Planes section). 6. Keep the SW, TG, and BOOST nodes away from sensitive control signals (ITH, SENSE+, SENSE-, RT, etc.). These nodes have very large and fast moving signals and therefore should be kept on the output side of the HV regulator and occupy minimum PCB trace area. Debugging HV Buck Controller on PCB 1. Probe and synchronize the oscilloscope to the switching nodes (SW, SWA-H pins). It is helpful to use an oscilloscope current probe to monitor the currents in the inductors. 2. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to near dropout and until the peak of inductor current drops below the low current operation threshold--typically 25% of the maximum designed current level in Burst Mode operation. In pulse-skipping mode, the frequency should maintain at even lower peak inductor current compared to Burst Mode until a pulse is skipped to maintain the regulation. The frequency in forced continuous mode should not change with load current. Rev. A For more information www.analog.com 35 LTC3372 APPLICATIONS INFORMATION The duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise PCB implementation. 3. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PCB layout if regulator bandwidth optimization is not required. 4. Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. 5. Investigate if any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, bottom MOSFET, and the top MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the exposed ground pad of the IC. 6. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. 7. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, Schottky and the top MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the exposed ground pad of the IC. 36 PCB Layout Considerations for LV Regulators 1. Each of the VINA-H input supply pins should have a decoupling capacitor. The connections of the decoupling capacitors to their respective VINA-H pins should be kept as short as possible. The GND side of these capacitors should connect directly to the ground plane of the part. These capacitors provide the AC current to the internal power MOSFETs and their drivers. It is important to minimize inductance from these capacitors to the VIN pins of the VINA-H pins. 2. The switching power traces connecting SWA-H to the inductors should be minimized to reduce radiated EMI and parasitic coupling. Due to the fast voltage swing of the switching nodes, high input impedance sensitive nodes, such as the feedback nodes, should be shielded or kept far away from the switching nodes. 3. The return (GND side) of the switching regulators' output capacitors should be connected to the exposed pad (Pin 49, GND) of the IC through a ground plane. Minimize the trace length from the output capacitors to the inductor(s)/pin(s). 4. In a multiple power stage buck regulator application, the trace length of switch nodes to the inductor must be kept equal to ensure proper operation. 5. Kelvin connect the returns for RT, CT and the feedback dividers to an isolated shape (ground copper "island") tied to the GND pad of the IC. Other PCB Layout Considerations Care should be taken to minimize capacitance on the TEMP pin. If the TEMP voltage must drive more than ~30pF, then the pin should be isolated with a resistor placed close to the pin of a value between 10k and 100k. Keep in mind that any load on the isolation resistor will create a proportional error. Rev. A For more information www.analog.com LTC3372 TYPICAL APPLICATIONS 4.5V to 60V Input 3.3V/3A Output HV Buck Converter Plus Quad 1V/1.2V/1.8V/2.5V LV Regulators VIN 60V MAX 4.5V MIN CIN1 47F x2 CIN2 2.2F x2 VIN RUN 100k INTVCC PGOOD VOUTPRG 2.2nF 8.06k INTVCC TG ITH VINA VINB 10F x2 L1 1H SENSE+ SENSE- VOUT/EXTVCC VINH VING 649k VOUT 10F x2 L2 1H SWA SWB SWH SWG FB1 EN1 FB4 EN4 VINC VIND VINF VINE 665k 232k FB2 EN2 464k VOUT 806k FB3 EN3 649k PLL/MODE RT CT 10nF 90 100k INTVCC 3372 TA02 EFFICIENCY (%) 60 50 40 10 0 0.0001 VOUT AC-COUPLED 100mV/DIV 1000 FCM LOSS PULSE-SKIPPING LOSS 100 BURST LOSS 10 30 20 PULSE-SKIPPING EFFICIENCY ILOAD 5A/DIV 1 FCM EFFICIENCY 0.001 0.01 0.1 1 OUTPUT CURRENT (A) *FULL LOAD IS EQUIVALENT TO SPECIFIED LOAD CURRENT PLUS THE FULL LOAD INPUT CURRENT FROM VOUT1-4 10000 POWER LOSS (mW) 70 47F VOUT3 1.8V 2A HV Controller Forced Continuous Mode Load Step VIN = 12V BURST EFFICIENCY VOUT = 3.3V 80 47F VOUT4 2.5V 2A 10F x2 SWF SWE TEMP WDI WDO RSTB C1 C2 C3 COUT1 150F x2 309k HV Controller Efficiency and Power Loss vs Output Current 100 1nF 10F x2 L3 1H SWC SWD 402k 10 VOUT 3.3V COUT2 3A* 47F VOUT L4 1H LTC3372 162k 47F RSENSE 5m TRACK/SS VOUT MTOP: RJK0651DPB MTOP: NTMFS5C670NL LHV: XAL1010-222ME CIN1: 63HVH47M CIN2: GRM32ER72A225KA35L COUT1: T520B157M006ATE025 COUT2: GRM32ER71A476KE15 D1: DFLS1100 MBOT BG GND VOUT2 1.2V 2A MTOP LHV 2.2H SW 0.01F 47F 0.1F BOOST 100pF VOUT1 1V 2A 4.7F D1 10 100s/DIV VIN = 12V VOUT = 3.3V ILOAD = 200mA to 8A 0.1 3372 TA02c 3372 TA02b Rev. A For more information www.analog.com 37 LTC3372 TYPICAL APPLICATIONS 6V to 60V Input 5V/10A Output HV Buck Converter Plus Quad 1.2V/3A, 1.8V/1A, 2.5V/1A, and 3.3V/3A LV Regulators VIN 60V MAX 6V MIN CIN1 47F x2 CIN2 2.2F x2 VIN RUN 100k INTVCC PGOOD VOUTPRG INTVCC ITH VOUT1 1.2V 3A 22F GND VINA VINB VINC VINH VING VINF L1 0.68H 464k VOUT LTC3372 SWA SWB SWC SWH SWG SWF FB1 EN1 FB4 EN4 VIND VINE 10F x3 L4 0.68H 511k 47F SWE 665k 806k FB2 EN2 PLL/MODE 649k RT CT 402k 10nF FB3 EN3 TEMP WDI WDO RSTB C1 C2 C3 100k INTVCC 3372 TA03a INTVCC EFFICIENCY (%) 60 PULSE-SKIPPING LOSS 100 50 BURST LOSS 40 30 10 0 0.0001 10 PULSE-SKIPPING EFFICIENCY 1 20 FCM EFFICIENCY 0.001 VOUT AC-COUPLED 100mV/DIV 1000 0.01 0.1 1 OUTPUT CURRENT (A) 1020 POWER LOSS (mW) 70 10000 FCM LOSS 80 *FULL LOAD IS EQUIVALENT TO SPECIFIED LOAD CURRENT PLUS THE FULL LOAD INPUT CURRENT FROM VOUT1-4 HV Controller Forced Continuous Mode Load Step BURST EFFICIENCY 90 22F VOUT3 2.5V 1A 309k HV Controller Efficiency and Power Loss vs Output Current 100 22F VOUT4 3.3V 3A VOUT L3 2.2H SWD MTOP: NTMFS5C670NL MBOT: NVMFS5C645NL LHV:XAL1010-152ME CIN1: 63HVH47M CIN2: GRM32ER72A225KA35L COUT1: 6TPE330MAP COUT2: GRM32ER71A476KE15 D1: DFLS1100 VOUT 10F L2 2.2H 22F COUT2 47F 162k 10F VOUT2 1.8V 1A COUT1 330F 10 1nF VOUT 5V 10A* TRACK/SS 232k 47F SW SENSE+ SENSE- VOUT/EXTVCC RSENSE 3m LHV 1.5H MBOT BG 0.01F 10F x3 MTOP 0.1F BOOST 100pF 4.7F D1 TG 3.3nF 5.11k VOUT INTVCC 0.1 ILOAD 5A/DIV 100s/DIV VIN = 12V VOUT = 5V ILOAD = 200mA to 12A 3372 TA03c 3372 TA03b 38 Rev. A For more information www.analog.com LTC3372 TYPICAL APPLICATIONS 4.5V to 60V Input 3.3V/10A Output HV Buck Converter Plus Quad 1V/4A, 1.2V/1A, 1.8V/1A and 2.5V/2A LV Regulators VIN 60V MAX 4.5V MIN CIN1 47F x2 CIN2 2.2F x2 INTVCC 6.34k VIN RUN 100k INTVCC PGOOD VOUTPRG 2.2nF ITH BOOST VINA VINB VINC VINH 10F x2 L1 0.4H SWA SWB SWC SWH FB1 EN1 162k 649k VOUT SENSE+ SENSE- VOUT/EXTVCC VING VINF MTOP: BSZ099N06LS5 MBOT: BSZ067N06LS3 LHV: XAL1010-102ME CIN1: 63HVH47M CIN2: GRM32ER72A225KA35L COUT1: T520B157M006ATE025 COUT2: GRM32ER71A476KE15 D1: DFLS1100 665k EN4 VINE VOUT 10F L3 1.5H SWD SWE FB2 EN2 FB3 EN3 TEMP WDI WDO RSTB 806k 464k PLL/MODE RT CT INTVCC 100k INTVCC 3372 TA04a EFFICIENCY (%) 60 10000 PULSE-SKIPPING LOSS 100 50 BURST LOSS 40 30 10 0 0.0001 10 PULSE-SKIPPING EFFICIENCY 1 20 FCM EFFICIENCY 0.001 VOUT AC-COUPLED 100mV/DIV 1000 0.01 0.1 1 OUTPUT CURRENT (A) 1020 POWER LOSS (mW) 70 *FULL LOAD IS EQUIVALENT TO SPECIFIED LOAD CURRENT PLUS THE FULL LOAD INPUT CURRENT FROM VOUT1-4 HV Controller Forced Continuous Mode Load Step FCM LOSS 80 22F VOUT3 1.8V 1A 649k C1 C2 C3 10nF VOUT4 2.5V 2A 309k 232k BURST EFFICIENCY 90 47F FB4 HV Controller Efficiency and Power Loss vs Output Current 100 COUT2 47F VOUT SWG SWF L2 1.5H 255k COUT1 150F x2 10F x2 L4 0.6H LTC3372 VIND 22F 10 1nF VOUT 3.3V 10A* TRACK/SS VOUT VOUT2 1.2V 1A RSENSE 3m LHV 1H MBOT BG GND 10F MTOP 0.1F SW 0.01F 47F x2 4.7uF TG 100pF VOUT1 1V 4A D1 ILOAD 5A/DIV 100s/DIV VIN = 12V VOUT = 3.3V ILOAD = 200mA to 12A 0.1 3372 TA04c 3372 TA04b Rev. A For more information www.analog.com 39 LTC3372 TYPICAL APPLICATIONS 4.5V (3V Minimum After Start-Up) to 50V Input HV SEPIC Converter Feeding Dual 3.3V/4A LV Regulators VIN 4.5V MIN 50V MAX (3V MIN AFTER START-UP) CIN1 47F x2 CIN2 10F DIN 1F INTVCC VIN RUN 100k PGOOD VOUTPRG INTVCC 6.8nF 4.32k INTVCC ITH TRACK/SS VINA VINB VINC VIND SWA SWB SWC SWD SWH SWG SWF SWE FB1 EN1 FB4 EN4 FB2 EN2 FB3 EN3 GND VOUT 10F x4 L1 0.33H 47F x2 511k 162k M1: TPH7R006PL LHV1, LHV2: 74485540120 CIN1: 63HVH47M CIN2: GRM32ER71H106KA12L COUT1: TPSE687M006R0045 COUT2: GRM32ER60J227ME05L CP: GRM32ER71H106KA12L DIN: DFLS1100 PLL/MODE RT CT TEMP WDI WDO C1 C2 C3 RSTB 255k 10nF COUT1 680F x2 100 INTVCC 1nF 100 BG SENSE+ SENSE- VOUT/EXTVCC VINH VING LTC3372 VINF VINE DFW M1 SW 0.01F CP 10F 4.7F TG BOOST 100pF VOUT1 3.3V 4A LHV1 1.2H 10F x4 RSENSE 2m VOUT 5V COUT2 220F LHV2 1.2H VOUT L2 0.33H 511k VOUT4 3.3V 47F 4A x2 162k 100k INTVCC INTVCC 3372 TA05a HV Controller Efficiency and Power Loss vs Output Current HV Controller VIN Step Response 10000 100 90 1000 70 100 60 BURST LOSS 10 40 30 20 10 0 0.0001 PULSE-SKIPPING EFFICIENCY 1 12V 3V VIN 5V/DIV 1 PULSE-SKIPPING LOSS 0.001 0.01 0.1 OUTPUT CURRENT (A) POWER LOSS (mW) EFFICIENCY (%) 80 50 VOUT AC-COUPLED 200mV/DIV BURST EFFICIENCY 6 0.1 VOUT = 5V ILOAD = 4.8A 200ms/DIV 3372 TA05c 3372 TA05b 40 Rev. A For more information www.analog.com LTC3372 TYPICAL APPLICATIONS 6V to 60V Input 5V/20A Output HV Buck Converter Plus Triple 3.3V/4A, 1.8V/1A and 1.2V/3A LV Regulators VIN 40V MAX 6V MIN CIN1 100F x2 CIN2 10F x4 100k INTVCC INTVCC 4.7nF 5.11k VIN RUN PGOOD VOUTPRG INTVCC ITH BOOST LHV 1H 0.1F SW VOUT SENSE+ SENSE- VOUT/EXTVCC VINH VING VINF VINA VINB VINC VIND SWA SWB SWC SWD 10F x4 L1 0.56H 511k LTC3372 SWH SWG SWF FB1 EN1 162k VOUT 10F x3 L4 0.68H 232k FB4 EN4 47F VOUT 10F L3 2.2H SWE 806k FB2 EN2 FB3 EN3 PLL/MODE RT CT TEMP WDI WDO RSTB C1 C2 C3 10nF 22F VOUT4 1.2V 3A 464k VINE 402k COUT2 220F VOUT 5V 20A* TRACK/SS GND MTOP: BSC014N04LSI MBOT: BSC010N04LSI LHV: XAL1010-102ME CIN1: UCJ1H101MCL1GS CIN2: GRM32ER71H106KA12L COUT1: 6TPE330MAP COUT2: GRM32ER60J227ME05L D1: DFLS1100 COUT1 330F x2 6.19k 100nF MBOT BG 0.01F 47F x2 4.7F MTOP TG 100pF VOUT1 3.3V 4A D1 22F VOUT3 1.8V 1A 649k 100k INTVCC INTVCC *FULL LOAD IS EQUIVALENT TO SPECIFIED LOAD CURRENT PLUS THE FULL LOAD INPUT CURRENT FROM VOUT1-4 3372 TA06a HV Controller Efficiency and Power Loss vs Output Current 100 90 10000 BURST EFFICIENCY FCM LOSS 1000 70 60 PULSE-SKIPPING LOSS 50 40 30 20 10 0 0.0001 0.001 100 BURST LOSS 10 PULSE-SKIPPING EFFICIENCY 1 FCM EFFICIENCY 0.01 0.1 1 OUTPUT CURRENT (A) 10 30 POWER LOSS (mW) EFFICIENCY (%) 80 HV Controller Forced Continuous Mode Load Step VOUT AC-COUPLED 100mV/DIV ILOAD 10A/DIV 100s/DIV 3372 TA06c VIN = 12V VOUT = 5V ILOAD = 200mA to 20A 0.1 3372 TA06b Rev. A For more information www.analog.com 41 LTC3372 PACKAGE DESCRIPTION UK Package 48-Lead Plastic QFN (7mm x 7mm) (Reference LTC DWG # 05-08-1704 Rev C) 0.70 0.05 5.15 0.05 5.50 REF 6.10 0.05 7.50 0.05 (4 SIDES) 5.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 7.00 0.10 (4 SIDES) 0.75 0.05 R = 0.10 TYP R = 0.115 TYP 47 48 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 PIN 1 CHAMFER C = 0.35 5.50 REF (4-SIDES) 5.15 0.10 5.15 0.10 0.200 REF 0.00 - 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WKKD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 42 (UK48) QFN 0406 REV C 0.25 0.05 0.50 BSC BOTTOM VIEW--EXPOSED PAD Rev. A For more information www.analog.com LTC3372 REVISION HISTORY REV DATE DESCRIPTION A 03/19 Updated conditions in the Electrical Characteristics tables PAGE NUMBER 4, 6 Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license For is granted implication or otherwise under any patent or patent rights of Analog Devices. moreby information www.analog.com 43 LTC3372 TYPICAL APPLICATION VIN 40V MAX 6V MIN CIN1 100F x2 CIN2 10F x4 100k INTVCC 5.11k INTVCC 4.7nF VIN RUN PGOOD VOUTPRG INTVCC 4.7F MTOP TG ITH SW 0.01F VOUT 10F x4 L1 0.56H 47F x2 511k 162k VOUT MTOP: BSC014N04LSI MBOT: BSC010N04LSI LHV: XAL1010-102ME CIN1: UCJ1H101MCL1GS CIN2: GRM32ER71H106KA12L COUT1: 6TPE330MAP COUT2: GRM32ER60J227ME05L D1: DFLS1100 GND VINA VINB VINC VIND SWA SWB SWC SWD MBOT BG TRACK/SS SENSE+ SENSE- VOUT/EXTVCC VINH VING VINF SWH LTC3372 SWG SWF FB1 EN1 FB4 EN4 VINE SWE 402k 10F x3 L4 0.68H 232k L3 2.2H 10nF INTVCC COUT1 330F x2 6.19k 100nF COUT2 220F VOUT 5V 20A* VOUT 47F 22F VOUT4 1.2V 3A 464k 806k 10F FB2 FB3 EN2 EN3 PLL/MODE TEMP RT WDI CT WDO C1 C2 C3 RSTB LHV 1H 0.1F BOOST 100pF VOUT1 3.3V 4A D1 22F VOUT3 1.8V 1A 649k 100k INTVCC *FULL LOAD IS EQUIVALENT TO SPECIFIED LOAD CURRENT PLUS THE FULL LOAD INPUT CURRENT FROM VOUT1-4 3372 TA07 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3891/LTC3890/ LTC3890-1/LTC3890-2/ LTC3890-3 60V, Low IQ, Single/Dual Synchronous Step-Down DC/ DC Controller Phase-Lockable Frequency 75kHz to 750kHz, 4V VIN 60V, 0.8V VOUT 24V, IQ =50A LTC3891: Single Channel; LTC3890/LTC3890-1/LTC3890-2/LTC3890-3 LTC3371/LTC3370 4-Channel Configurable DC/DC with 8 x 1A Power Stages 4 Synchronous Buck Regulators with 8 x 1A Power Stages. Can Connect Up to Four Power Stages in Parallel, 8 Output Configurations Possible. LTC3370: Precision PGOODALL Indication, 32-Lead (5mm x 5mm x 0.75mm) QFN Package. LTC3371: Precision RST Monitoring with Windowed Watchdog Timer (CT Programmable), 38-Lead (5mm x 7mm x 0.75mm) QFN and TSSOP Packages LTC3892/LTC3892-1/ LTC3892-2 60V, Low IQ, Dual, 2-Phase Synchronous Step-Down DC/ DC Controller Phase-Lockable Frequency 75kHz to 850kHz, 4.5V VIN 60V, 0.8V VOUT 99% VIN, IQ = 29A, Adjustable 5V to 10V Gate Drive, No External Bootstrap Diode LTC3589 8-Output Regulator with Sequencing and I2C Triple I2C Adjustable High Efficiency Step-Down DC/DC Converters: 1.6A, 1A, 1A. High Efficiency 1.2A Buck-Boost DC/DC Converter, Triple 250mA LDO Regulators, 40-Lead (6mm x 6mm x 0.75mm) QFN. LTC3675 7-Channel Configurable High Power PMIC Quad Synchronous Buck Regulators (1A, 1A, 500mA, 500mA). Buck DC/DCs Can be Paralleled to Deliver Up to 2x Current with a Single Inductor. 1A Boost, 1A Buck- Boost, 40V LED Driver. 44-Lead (4mm x 7mm x 0.75mm) QFN Package. LTC3676 8-Channel Power Management Solution for Application Processor Quad Synchronous Buck Regulators (2.5A, 2.5A, 1.5A, 1.5A). Quad LDO Regulators (300mA, 300mA, 300mA, 25mA). 40-Lead (6mm x 6mm x 0.75mm) QFN Package. LTC3375/LTC3374/ LTC3374A 8-Channel Programmable Configurable 1A DC/DC 8 x 1A Synchronous Buck Regulators. Can Connect Up to Four Power Stages in Parallel with a Single Inductor, 15 Output Configurations Possible, 48-Lead (7mm x 7mm x 0.75mm) QFN Package (LTC3375) 38-Lead (5mm x 7mm x 0.75mm) QFN and TSSOP Packages (LTC3374A) 44 Rev. A D16975-0-3/19(A) www.analog.com For more information www.analog.com ANALOG DEVICES, INC. 2018-2019