LP38691,LP38693 LP38691 LP38693 500mA Low Dropout CMOS Linear Regulators Stable with Ceramic Output Capacitors Literature Number: SNVS321I 500mA Low Dropout CMOS Linear Regulators Stable with Ceramic Output Capacitors General Description Features The LP38691/3 low dropout CMOS linear regulators provide tight output tolerance (2.0% typical), extremely low dropout voltage (250 mV @ 500mA load current, VOUT = 5V), and excellent AC performance utilizing ultra low ESR ceramic output capacitors. The low thermal resistance of the LLP, SOT-223 and TO-252 packages allow the full operating current to be used even in high ambient temperature environments. The use of a PMOS power transistor means that no DC base drive current is required to bias it allowing ground pin current to remain below 100 A regardless of load current, input voltage, or operating temperature. Dropout Voltage: 250 mV (typ) @ 500mA (typ. 5V out). Ground Pin Current: 55 A (typ) at full load. Precision Output Voltage: 2.0% (25C) accuracy. All LLP options are available as AEC-Q100 Grade 1 2.0% output accuracy (25C) Low dropout voltage: 250 mV @ 500mA (typ, 5V out) Wide input voltage range (2.7V to 10V) Precision (trimmed) bandgap reference Guaranteed specs for -40C to +125C 1A off-state quiescent current Thermal overload protection Foldback current limiting T0-252, SOT-223 and 6-Lead LLP packages Enable pin (LP38693) Applications Hard Disk Drives Notebook Computers Battery Powered Devices Portable Instrumentation Typical Application Circuits 20126501 20126502 Note: * Minimum value required for stability. **LLP package devices only. (c) 2011 National Semiconductor Corporation 201265 www.national.com LP38691/LP38693 500mA Low Dropout CMOS Linear Regulators Stable with Ceramic Output Capacitors June 27, 2011 LP38691 LP38693 LP38691/LP38693 Connection Diagrams 20126504 SOT-223, Top View LP38693MP-X.X 20126503 TO-252, Top View LP38691DT-X.X 20126505 20126506 6-Lead LLP, Top View LP38691SD-X.X 6-Lead LLP, Top View LP38693SD-X.X Pin Descriptions Pin Description VIN This is the input supply voltage to the regulator. For LLP devices, both VIN pins must be tied together for full current operation (250mA maximum per pin). GND Circuit ground for the regulator. For the TO-252 and SOT-223 packages this is thermally connected to the die and functions as a heat sink when the soldered down to a large copper plane. SNS Output sense pin allows remote sensing at the load which will eliminate the error in output voltage due to voltage drops caused by the resistance in the traces between the regulator and the load. This pin must be tied to VOUT. VEN The enable pin allows the part to be turned ON and OFF by pulling this pin high or low. VOUT Regulated output voltage DAP LLP Only - The DAP (Exposed Pad) functions as a thermal connection when soldered to a copper plane. See LLP MOUNTING section in Application Hints for more information. www.national.com 2 Output Voltage Order Number LP38691SD-1.8 LP38691SDX-1.8 LP38691QSD-1.8 LP38691QSDX-1.8 LP38691DT-1.8 1.8V LP38691DTX-1.8 LP38693SD-1.8 LP38693SDX-1.8 LP38693QSD-1.8 LP38693QSDX-1.8 LP38693MP-1.8 LP38693MPX-1.8 LP38691SD-2.5 LP38691SDX-2.5 LP38691QSD-2.5 LP38691QSDX-2.5 LP38691DT-2.5 2.5V LP38691DTX-2.5 LP38693SD-2.5 LP38693SDX-2.5 LP38693QSD-2.5 LP38693QSDX-2.5 LP38693MP-2.5 LP38693MPX-2.5 LP38691SD-3.3 LP38691SDX-3.3 LP38691QSD-3.3 LP38691QSDX-3.3 LP38691DT-3.3 3.3V LP38691DTX-3.3 LP38693SD-3.3 LP38693SDX-3.3 LP38693QSD-3.3 LP38693QSDX-3.3 LP38693MP-3.3 LP38693MPX-3.3 Grade Package Marking Package Type Package Drawing Standard L118B 6-Lead LLP SDE06A Automotive L256B 6-Lead LLP SDE06A Standard LP38691DT-1.8 TO-252 TD03B Standard L128B 6-Lead LLP SDE06A Automotive L260B 6-Lead LLP SDE06A Standard LJVB SOT-223 MP05A Standard L119B 6-Lead LLP SDE06A Automotive L257B 6-Lead LLP SDE06A Standard LP38691DT-2.5 TO-252 TD03B Standard L129B 6-Lead LLP SDE06A Automotive L261B 6-Lead LLP SDE06A Standard LJXB SOT-223 MP05A Standard L120B 6-Lead LLP SDE06A Automotive L258B 6-Lead LLP SDE06A Standard LP38691DT-3.3 TO-252 TD03B Standard L130B 6-Lead LLP SDE06A Automotive L262B 6-Lead LLP SDE06A Standard LJYB SOT-223 MP05A 3 Supplied As Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Rail of 75 Units Reel of 2500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 2000 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Rail of 75 Units Reel of 2500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 2000 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Rail of 75 Units Reel of 2500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 2000 Units www.national.com LP38691/LP38693 Ordering Information LP38691/LP38693 Output Voltage Order Number LP38691SD-5.0 LP38691SDX-5.0 LP38691QSD-5.0 LP38691QSDX-5.0 LP38691DT-5.0 5.0V LP38691DTX-5.0 LP38693SD-5.0 LP38693SDX-5.0 LP38693QSD-5.0 LP38693QSDX-5.0 LP38693MP-5.0 LP38693MPX-5.0 Grade Package Marking Package Type Package Drawing Standard L121B 6-Lead LLP SDE06A Automotive L259B 6-Lead LLP SDE06A Standard LP38691DT-5.0 TO-252 TD03B Standard L131B 6-Lead LLP SDE06A Automotive L263B 6-Lead LLP SDE06A Standard LJZB SOT-223 MP05A Supplied As Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Rail of 75 Units Reel of 2500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 4500 Units Reel of 1000 Units Reel of 2000 Units Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC Q100 standard. Automotive Grade products are identified with the letter Q. For more information go to: http://www.national.com/automotive For LP38691 Ordering and Availability Information see: http://www.national.com/pf/LP/LP38691.html#Order For LP38693 Ordering and Availability Information see: http://www.national.com/pf/LP/LP38693.html#Order www.national.com 4 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Lead Temp. (Soldering, 5 seconds) ESD Rating (Note 3) Power Dissipation (Note 2) -0.3V to 12V Internally Limited -40C to +150C Operating Ratings -65C to +150C 260C 2 kV Internally Limited VIN Supply Voltage Operating Junction Temperature Range 2.7V to 10V -40C to +125C Electrical Characteristics Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VOUT + 1V, CIN = COUT = 10 F, ILOAD = 10mA. Min/Max limits are guaranteed through testing, statistical correlation, or design. Symbol Parameter Conditions 100 A < IL < 0.5A Min Typ (Note 4) Max -2.0 2.0 -4.0 4.0 Units VO Output Voltage Tolerance VO/VIN Output Voltage Line Regulation (Note 6) VO + 0.5V VIN 10V IL = 25mA 0.03 0.1 %/V VO/IL Output Voltage Load Regulation (Note 7) 1 mA < IL < 0.5A VIN = VO + 1V 1.8 5 %/A (VO = 2.5V) IL = 0.1A IL = 0.5A 80 430 145 725 (VO = 3.3V) IL = 0.1A IL = 0.5A 65 330 110 550 (VO = 5V) IL = 0.1A IL = 0.5A 45 250 100 450 VIN 10V, IL =100 A - 0.5A 55 100 VEN 0.4V, (LP38693 Only) 0.001 1 VIN - VOUT IQ VO + 1V VIN 10V Dropout Voltage (Note 8) Quiescent Current IL(MIN) Minimum Load Current VIN - VO 4V IFB Foldback Current Limit VIN - VO > 5V 350 VIN - VO < 4V 850 VIN = VO + 2V(DC), with 1V(p-p) / 120Hz Ripple 55 %VOUT mV A 100 PSRR Ripple Rejection TSD Thermal Shutdown Activation (Junction Temp) 160 TSD (HYST) Thermal Shutdown Hysteresis (Junction Temp) 10 mA dB C 5 www.national.com LP38691/LP38693 V(max) All pins (with respect to GND) IOUT Junction Temperature Absolute Maximum Ratings (Note 1) LP38691/LP38693 Symbol Parameter Conditions Min Typ (Note 4) en Output Noise BW = 10Hz to 10kHz VO = 3.3V 0.7 VO (LEAK) Output Leakage Current VO = VO(NOM) + 1V @ 10VIN 0.5 VEN Enable Voltage (LP38693 Only) Output = OFF IEN Enable Pin Leakage (LP38693 Only) Max Units V/ 12 A 0.4 Output = ON, VIN = 4V 1.8 Output = ON, VIN = 6V 3.0 Output = ON, VIN = 10V 4.0 VEN = 0V or 10V, VIN = 10V -1 V 0.001 1 A Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not apply when operating the device outside of its rated operating conditions. Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink values (if a heatsink is used). The junction-to-ambient thermal resistance ( J-A) for the TO-252 is approximately 90C/W for a PC board mounting with the device soldered down to minimum copper area (less than 0.1 square inch). If one square inch of copper is used as a heat dissipator for the TO-252, the J-A drops to approximately 50C/W. The SOT-223 package has a J-A of approximately 125C/W when soldered down to a minimum sized pattern (less than 0.1 square inch) and approximately 70C/W when soldered to a copper area of one square inch. The J-A values for the LLP package are also dependent on trace area, copper thickness, and the number of thermal vias used (refer to application note AN-1187 and the LLP MOUNTING section in this datasheet). If power dissipation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown. Note 3: ESD is tested using the human body model which is a 100pF capacitor discharged through a 1.5k resistor into each pin. Note 4: Typical numbers represent the most likely parametric norm for 25C operation. Note 5: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground. Note 6: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage. Note 7: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from 1mA to full load. Note 8: Dropout voltage is defined as the minimum input to output differential required to maintain the output within 100mV of nominal value. www.national.com 6 LP38691/LP38693 Block Diagrams 20126507 FIGURE 1. LP38691 Functional Diagram (LLP) 20126508 FIGURE 2. LP38691 Functional Diagram (TO-252) 7 www.national.com LP38691/LP38693 20126509 FIGURE 3. LP38693 Functional Diagram (LLP) 20126510 FIGURE 4. LP38693 Functional Diagram (SOT-223) www.national.com 8 Unless otherwise specified: TJ = 25C, CIN = COUT = 10 F, Enable pin is tied to VIN (LP38693 only), VOUT = 1.8V, VIN = VOUT +1V, IL = 10mA. Noise vs Frequency Noise vs Frequency 20126536 20126535 Noise vs Frequency Ripple Rejection 20126518 20126537 Ripple Rejection Ripple Rejection 20126520 20126522 9 www.national.com LP38691/LP38693 Typical Performance Characteristics LP38691/LP38693 Line Transient Response Line Transient Response 20126524 20126526 Line Transient Response Load Transient Response 20126528 20126542 Load Transient Response VOUT vs Temperature (5.0V) 20126544 20126530 www.national.com 10 LP38691/LP38693 VOUT vs Temperature (3.3V) VOUT vs Temperature (2.5V) 20126532 20126531 VOUT vs Temperature (1.8V) VOUT vs VIN (1.8V) 20126533 20126559 VOUT vs VIN, Power-Up VOUT vs VEN, ON (LP38693 Only) 20126560 20126561 11 www.national.com LP38691/LP38693 VOUT vs VEN, OFF (LP38693 Only) Enable Voltage vs Temperature 20126552 20126562 Load Regulation vs Temperature Line Regulation vs Temperature 20126553 20126554 MIN VIN vs IOUT Dropout Voltage vs IOUT 20126556 20126557 www.national.com 12 EXTERNAL CAPACITORS Like any low-dropout regulator, external capacitors are required to assure stability. These capacitors must be correctly selected for proper performance. INPUT CAPACITOR: An input capacitor of at least 1F is required (ceramic recommended). The capacitor must be located not more than one centimeter from the input pin and returned to a clean analog ground. OUTPUT CAPACITOR: An output capacitor is required for loop stability. It must be located less than 1 centimeter from the device and connected directly to the output and ground pins using traces which have no other currents flowing through them. The minimum amount of output capacitance that can be used for stable operation is 1F. Ceramic capacitors are recommended (the LP38691/3 was designed for use with ultra low ESR capacitors). The LP38691/3 is stable with any output capacitor ESR between zero and 100 Ohms. ENABLE PIN (LP38693 only): The LP38693 has an Enable pin (EN) which allows an external control signal to turn the regulator output On and Off. The Enable On/Off threshold has no hysteresis. The voltage signal must rise and fall cleanly, and promptly, through the ON and OFF voltage thresholds. The Enable pin has no internal pull-up or pull-down to establish a default condition and, as a result, this pin must be terminated either actively or passively. If the Enable pin is driven from a source that actively pulls high and low, the drive voltage should not be allowed to go below ground potential or higher than VIN. If the application does not require the Enable function, the pin should be connected directly to the VIN pin. Foldback Current Limiting: Foldback current limiting is built into the LP38691/3 which reduces the amount of output current the part can deliver as the output voltage is reduced. The amount of load current is dependent on the differential voltage between VIN and VOUT. Typically, when this differential voltage exceeds 5V, the load current will limit at about 350 mA. When the VIN - VOUT differential is reduced below 4V, load current is limited to about 850 mA. TANTALUM Solid Tantalum capacitors have good temperature stability: a high quality Tantalum will typically show a capacitance value that varies less than 10-15% across the full temperature range of -40C to +125C. ESR will vary only about 2X going from the high to low temperature limits. REVERSE VOLTAGE A reverse voltage condition will exist when the voltage at the output pin is higher than the voltage at the input pin. Typically this will happen when VIN is abruptly taken low and COUT continues to hold a sufficient charge such that the input to output voltage becomes reversed. A less common condition is when an alternate voltage source is connected to the output. There are two possible paths for current to flow from the output pin back to the input during a reverse voltage condition. 1) While VIN is high enough to keep the control circuity alive, and the Enable pin (LP38693 only) is above the VEN(ON) threshold, the control circuitry will attempt to regulate the output voltage. If the input voltage is less than the programmed output voltage, the control circuit will drive the gate of the pass element to the full ON condition. In this condition, reverse current will flow from the output pin to the input pin, limited only by the RDS(ON) of the pass element and the output to input voltage differential. Discharging an output capacitor up to 1000 F in this manner will not damage the device as the current will rapidly decay. However, continuous reverse current should be avoided. When the Enable pin is low this condition will be prevented. 2) The internal PFET pass element has an inherent parasitic diode. During normal operation, the input voltage is higher than the output voltage and the parasitic diode is reverse biased. However, when VIN is below the value where the control circuity is alive, or the Enable pin is low (LP38693 only), and the output voltage is more than 500 mV (typical) above the input voltage the parasitic diode becomes forward biased and current flows from the output pin to the input pin through the diode. The current in the parasitic diode should be limited to less than 1A continuous and 5A peak. If used in a dual-supply system where the regulator output load is returned to a negative supply, the output pin must be diode clamped to ground to limit the negative voltage transition. A Schottky diode is recommended for this protective clamp. SELECTING A CAPACITOR It is important to note that capacitance tolerance and variation with temperature must be taken into consideration when selecting a capacitor so that the minimum required amount of capacitance is provided over the full operating temperature range. Capacitor Characteristics PCB LAYOUT Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors must be directly connected to the input, output, and ground pins of the regulator using traces which do not have other currents flowing in them (Kelvin connect). The best way to do this is to lay out CIN and COUT near the device with short traces to the VIN, VOUT, and ground pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a "single point ground". It should be noted that stability problems have been seen in applications where "vias" to an internal ground plane were used at the ground points of the IC and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground CERAMIC For values of capacitance in the 10 to 100 F range, ceramics are usually larger and more costly than tantalums but give superior AC performance for bypassing high frequency noise because of very low ESR (typically less than 10 m). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature range. X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a capacitance range within 20% of nominal over full operating 13 www.national.com LP38691/LP38693 ratings of temperature and voltage. Of course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance. Application Hints LP38691/LP38693 plane. Using a single point ground technique for the regulator and it's capacitors fixed the problem. Since high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. mance because of the small dimensions of the geometries inside the device. In applications where circuit sources are present which generate signals with significant high frequency energy content (> 1 MHz), care must be taken to ensure that this does not affect the IC regulator. If RFI/EMI noise is present on the input side of the regulator (such as applications where the input source comes from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the IC. If a load is connected to the IC output which switches at high speed (such as a clock), the high-frequency current pulses required by the load must be supplied by the capacitors on the IC output. Since the bandwidth of the regulator loop is less than 100 kHz, the control circuitry cannot respond to load changes above that frequency. This means the effective output impedance of the IC at frequencies above 100 kHz is determined only by the output capacitor(s). In applications where the load is switching at high speed, the output of the IC may need RF isolation from the load. It is recommended that some inductance be placed between the output capacitor and the load, and good RF bypass capacitors be placed directly across the load. PCB layout is also critical in high noise environments, since RFI/EMI is easily radiated directly into PC traces. Noisy circuitry should be isolated from "clean" circuits where possible, and grounded through a separate path. At MHz frequencies, ground planes begin to look inductive and RFI/ EMI can cause ground bounce across the ground plane. In multi-layer PCB applications, care should be taken in layout so that noisy power and ground planes do not radiate directly into adjacent layers which carry analog power and ground. LLP MOUNTING The SDE06A (No Pullback) 6-Lead LLP package requires specific mounting techniques which are detailed in National Semiconductor Application Note # 1187. Referring to the section PCB Design Recommendations in AN-1187 (Page 5), it should be noted that the pad style which should be used with the LLP package is the NSMD (non-solder mask defined) type. Additionally, it is recommended the PCB terminal pads to be 0.2 mm longer than the package pads to create a solder fillet to improve reliability and inspection. The input current is split between two VIN pins, 1 and 6. The two VIN pins must be connected together to ensure that the device can meet all specifications at the rated current. The thermal dissipation of the LLP package is directly related to the printed circuit board construction and the amount of additional copper area connected to the DAP. The DAP (exposed pad) on the bottom of the LLP package is connected to the die substrate with a conductive die attach adhesive. The DAP has no direct electrical (wire) connection to any of the pins. There is a parasitic PN junction between the die substrate and the device ground. As such, it is strongly recommend that the DAP be connected directly to the ground at device lead 2 (i.e. GND). Alternately, but not recommended, the DAP may be left floating (i.e. no electrical connection). The DAP must not be connected to any potential other than ground. For the LP38691SD and LP38693SD in the SDE06A 6-Lead LLP package, the junction-to-case thermal rating, JC, is 10.4C/W, where the case is the bottom of the package at the center of the DAP. The junction-to-ambient thermal performance for the LP38691SD and LP38693SD in the SDE06A 6-Lead LLP package, using the JEDEC JESD51 standards is summarized in the following table: Board Type Thermal Vias JC JA JEDEC 2-Layer JESD 51-3 None 10.4C/W 237 C/W 1 10.4C/W 74 C/W 2 10.4C/W 60 C/W 4 10.4C/W 49 C/W 6 10.4C/W 45 C/W JEDEC 4-Layer JESD 51-7 OUTPUT NOISE Noise is specified in two ways: Spot Noise or Output Noise Density is the RMS sum of all noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz bandwidth). This type of noise is usually plotted on a curve as a function of frequency. Total Output Noise or Broad-Band Noise is the RMS sum of spot noise over a specified bandwidth, usually several decades of frequencies. Attention should be paid to the units of measurement. Spot noise is measured in units V/root-Hz or nV/root-Hz and total output noise is measured in V(rms) The primary source of noise in low-dropout regulators is the internal reference. Noise can be reduced in two ways: by increasing the transistor area or by increasing the current drawn by the internal reference. Increasing the area will decrease the chance of fitting the die into a smaller package. Increasing the current drawn by the internal reference increases the total supply current (ground pin current). RFI/EMI SUSCEPTIBILITY RFI (radio frequency interference) and EMI (electromagnetic interference) can degrade any integrated circuit's perfor- www.national.com 14 LP38691/LP38693 Physical Dimensions inches (millimeters) unless otherwise noted 6-lead, LLP Package NS Package Number SDE06A TO-252 Package NS Package Number TD03B 15 www.national.com LP38691/LP38693 SOT-223 Package NS Package Number MP05A www.national.com 16 LP38691/LP38693 Notes 17 www.national.com LP38691/LP38693 500mA Low Dropout CMOS Linear Regulators Stable with Ceramic Output Capacitors Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated