TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS Copyright (c) 1999, Power Innovations Limited, UK NOVEMBER 1997 - REVISED APRIL 1999 TELECOMMUNICATION SYSTEM HIGH CURRENT OVERVOLTAGE PROTECTORS 8 kV 10/700, 200 A 5/310 ITU-T K20/21 rating Ion-Implanted Breakdown Region Precise and Stable Voltage Low Voltage Overshoot under Surge DEVICE VDRM LM PACKAGE (TOP VIEW) T(A) NC R(B) MD4XAT V(BO) V V `4070 58 70 `4080 65 80 NC - No internal connection on pin 2 LMF PACKAGE (LM PACKAGE WITH FORMED LEADS) (TOP VIEW) `4095 75 95 `4125 100 125 `4145 120 145 `4165 135 165 NC `4180 145 180 R(B) `4220 160 220 `4240 180 240 `4260 200 260 `4300 230 300 `4350 275 350 `4400 300 400 T(A) 1 2 3 MD4XAKB NC - No internal connection on pin 2 device symbol T Rated for International Surge Wave Shapes ITSP WAVE SHAPE STANDARD 2/10 s GR-1089-CORE 8/20 s IEC 61000-4-5 300 R 10/160 s FCC Part 68 250 Terminals T and R correspond to the alternative line designators of A and B 10/700 s ITU-T K20/21 FCC Part 68 A 500 200 10/560 s FCC Part 68 160 10/1000 s GR-1089-CORE 100 Low Differential Capacitance . . . 80 pF max. SD4XAA Ordering Information DEVICE TYPE 1 2 3 TISP4xxxH3LM PACKAGE TYPE Straight Lead DO-92 Bulk Pack TISP4xxxH3LMR Straight Lead DO-92 Tape and Reeled TISP4xxxH3LMFR Formed Lead DO-92 Tape and Reeled description These devices are designed to limit overvoltages on the telephone line. Overvoltages are normally caused by a.c. power system or lightning flash disturbances which are induced or conducted on to the telephone line. A single device provides 2-point protection and is typically used for the protection of 2-wire telecommunication equipment (e.g. between the Ring to Tip wires for telephones and modems). Combinations of devices can be used for multi-point protection (e.g. 3-point protection between Ring, Tip and Ground). The protector consists of a symmetrical voltage-triggered bidirectional thyristor. Overvoltages are initially clipped by breakdown clamping until the voltage rises to the breakover level, which causes the device to crowbar into a low-voltage on state. This low-voltage on state causes the current resulting from the overvoltage to be safely diverted through the device. The high crowbar holding current prevents d.c. latchup as the diverted current subsides. PRODUCT INFORMATION Information is current as of publication date. Products conform to specifications in accordance with the terms of Power Innovations standard warranty. Production processing does not necessarily include testing of all parameters. 1 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 description (continued) This TISP4xxxH3LM range consists of thirteen voltage variants to meet various maximum system voltage levels (58 V to 300 V). They are guaranteed to voltage limit and withstand the listed international lightning surges in both polarities. These protection devices are supplied in a DO-92 (LM) cylindrical plastic package. The TISP4xxxH3LM is a straight lead DO-92 supplied in bulk pack and on tape and reeled. The TISP4xxxH3LMF is a formed lead DO-92 supplied only on tape and reeled. absolute maximum ratings, TA = 25C (unless otherwise noted) RATING SYMBOL 58 `4080 65 `4095 75 `4125 100 `4145 120 `4180 UNIT 135 `4165 Repetitive peak off-state voltage, (see Note 1) VALUE `4070 VDRM 145 `4220 160 `4240 180 `4260 200 `4300 230 `4350 275 `4400 300 V Non-repetitive peak on-state pulse current (see Notes 2, 3 and 4) 2/10 s (GR-1089-CORE, 2/10 s voltage wave shape) 500 8/20 s (IEC 61000-4-5, combination wave generator, 1.2/50 voltage, 8/20 current) 300 10/160 s (FCC Part 68, 10/160 s voltage wave shape) 250 5/200 s (VDE 0433, 10/700 s voltage wave shape) 0.2/310 s (I 31-24, 0.5/700 s voltage wave shape) 220 ITSP 5/310 s (ITU-T K20/21, 10/700 s voltage wave shape) 200 A 200 5/310 s (FTZ R12, 10/700 s voltage wave shape) 200 5/320 s (FCC Part 68, 9/720 s voltage wave shape) 200 10/560 s (FCC Part 68, 10/560 s voltage wave shape) 160 10/1000 s (GR-1089-CORE, 10/1000 s voltage wave shape) 100 Non-repetitive peak on-state current (see Notes 2, 3 and 5) 20 ms (50 Hz) full sine wave 55 16.7 ms (60 Hz) full sine wave ITSM 1000 s 50 Hz/60 Hz a.c. Initial rate of rise of on-state current, Exponential current ramp, Maximum ramp value < 100 A Junction temperature Storage temperature range NOTES: 1. 2. 3. 4. 5. A diT/dt 400 A/s TJ -40 to +150 C Tstg -65 to +150 C See Applications Information and Figure 10 for voltage values at lower temperatures. Initially the TISP4xxxH3LM must be in thermal equilibrium with TJ = 25C. The surge may be repeated after the TISP4xxxH3LM returns to its initial conditions. See Applications Information and Figure 11 for current ratings at other temperatures. EIA/JESD51-2 environment and EIA/JESD51-3 PCB with standard footprint dimensions connected with 5 A rated printed wiring track widths. See Figure 8 for the current ratings at other durations. Derate current values at -0.61 %/C for ambient temperatures above 25 C PRODUCT 2 60 2.3 INFORMATION TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 electrical characteristics for the T and R terminals, TA = 25C (unless otherwise noted) PARAMETER IDRM V(BO) TEST CONDITIONS Repetitive peak offstate current Breakover voltage VD = VDRM dv/dt = 750 V/ms, RSOURCE = 300 dv/dt 1000 V/s, Linear voltage ramp, V(BO) Impulse breakover Maximum ramp value = 500 V voltage di/dt = 20 A/s, Linear current ramp, Maximum ramp value = 10 A MIN TYP 5 TA = 85C 10 `4070 70 `4080 80 `4095 95 `4125 125 `4145 145 `4165 165 `4180 180 `4220 220 `4240 240 `4260 260 `4300 300 `4350 350 `4400 400 `4070 78 `4080 88 `4095 102 `4125 132 `4145 151 `4165 171 `4180 186 `4220 227 `4240 247 `4260 267 `4300 308 `4350 359 RSOURCE = 300 Breakover current dv/dt = 750 V/ms, VT On-state voltage IT = 5 A, tW = 100 s Holding current IT = 5 A, di/dt = +/-30 mA/ms IH dv/dt ID Critical rate of rise of off-state voltage Off-state current VD = 50 V f = 100 kHz, f = 100 kHz, Coff Off-state capacitance f = 100 kHz, f = 100 kHz, f = 100 kHz, 0.15 Vd = 1 V rms, VD = -1 V Vd = 1 V rms, VD = -2 V Vd = 1 V rms, VD = -50 V Vd = 1 V rms, VD = -100 V A V V 0.6 A 3 V 0.6 A 5 kV/s TA = 85C Vd = 1 V rms, VD = 0, (see Note 6) NOTE 0.15 Linear voltage ramp, Maximum ramp value < 0.85VDRM UNIT 410 `4400 I(BO) MAX TA = 25C 10 `4070 thru `4095 172 218 `4125 thru `4220 95 120 `4240 thru `4400 92 115 `4070 thru `4095 157 200 `4125 thru `4220 85 110 `4240 thru `4400 80 100 `4070 thru `4095 145 185 `4125 thru `4220 78 100 `4240 thru `4400 72 90 `4070 thru `4095 70 90 `4125 thru `4220 33 43 `4240 thru `4400 28 35 `4125 thru `4220 25 33 `4240 thru `4400 22 28 A pF 6: To avoid possible voltage clipping, the `4125 is tested with VD = -98 V. PRODUCT INFORMATION 3 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 thermal characteristics PARAMETER MIN TEST CONDITIONS TYP MAX EIA/JESD51-3 PCB, IT = ITSM(1000), RJA 265 mm x 210 mm populated line card, 4-layer PCB, IT = ITSM(1000), TA = 25 C NOTE 105 TA = 25 C, (see Note 7) Junction to free air thermal resistance C/W 55 7: EIA/JESD51-2 environment and PCB has standard footprint dimensions connected with 5 A rated printed wiring track widths. PARAMETER MEASUREMENT INFORMATION +i Quadrant I ITSP Switching Characteristic ITSM IT V(BO) VT I(BO) IH VDRM -v IDRM ID VD ID IDRM VD VDRM +v IH I(BO) VT V(BO) IT ITSM Quadrant III ITSP Switching Characteristic -i Figure 1. VOLTAGE-CURRENT CHARACTERISTIC FOR T AND R TERMINALS ALL MEASUREMENTS ARE REFERENCED TO THE R TERMINAL PRODUCT 4 UNIT INFORMATION PMXXAAB TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 TYPICAL CHARACTERISTICS OFF-STATE CURRENT vs JUNCTION TEMPERATURE TCHAS 102 1.10 NORMALISED BREAKOVER VOLTAGE vs JUNCTION TEMPERATURE TC4HAF VD = 50 V 1 Normalised Breakover Voltage |ID| - Off-State Current - A 10 100 10-1 10-2 10-3 1.05 1.00 10-4 0.95 10-5 -25 0 25 50 75 100 125 TJ - Junction Temperature - C -25 150 Figure 2. ON-STATE CURRENT vs ON-STATE VOLTAGE 200 150 100 TC4HAC Normalised Holding Current IT - On-State Current - A 1 0.7 '4125 THRU '4200 '4240 THRU '4400 NORMALISED HOLDING CURRENT vs JUNCTION TEMPERATURE TC4HAD 1.5 20 15 2 1.5 2.0 TA = 25 C tW = 100 s 50 40 30 7 5 4 3 150 Figure 3. 70 10 0 25 50 75 100 125 TJ - Junction Temperature - C '4070 THRU '4095 1.0 0.9 0.8 0.7 0.6 0.5 0.4 1 1.5 2 3 4 5 VT - On-State Voltage - V 7 10 Figure 4. PRODUCT -25 0 25 50 75 100 125 TJ - Junction Temperature - C 150 Figure 5. INFORMATION 5 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 TYPICAL CHARACTERISTICS DIFFERENTIAL OFF-STATE CAPACITANCE vs RATED REPETITIVE PEAK OFF-STATE VOLTAGE Capacitance Normalised to VD = 0 Vd = 1 Vrms 0.7 0.6 0.5 '4070 THRU '4095 0.4 '4125 THRU '4220 0.3 '4240 THRU '4400 0.2 0.5 '4300 '4240 '4260 '4165 '4180 '4220 '4145 '4125 80 75 70 C = Coff(-2 V) - Coff(-50 V) 65 60 55 50 45 40 1 2 3 5 10 20 30 50 100150 VD - Off-state Voltage - V Figure 6. PRODUCT 6 85 '4095 TJ = 25C 0.8 C - Differential Off-State Capacitance - pF 0.9 TCHAE 90 '4350 '4400 TC4HAQ 1 '4070 '4080 NORMALISED CAPACITANCE vs OFF-STATE VOLTAGE INFORMATION 50 60 70 80 90100 150 200 250 300 VDRM - Repetitive Peak Off-State Voltage - V Figure 7. TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 RATING AND THERMAL INFORMATION THERMAL IMPEDANCE vs POWER DURATION 30 - Transient Thermal Impedance - C/W VGEN = 600 Vrms, 50/60 Hz RGEN = 1.4*VGEN/ITSM(t) 20 EIA/JESD51-2 ENVIRONMENT EIA/JESD51-3 PCB TA = 25 C 15 10 9 8 7 6 5 4 JA(t) 3 2 1.5 0*1 1 10 100 100 80 60 50 40 30 20 15 10 8 1 10 100 1000 t - Power Duration - s Figure 8. Figure 9. VDRM DERATING FACTOR IMPULSE RATING vs AMBIENT TEMPERATURE vs MINIMUM AMBIENT TEMPERATURE TI4HAI 1.00 EIA/JESD51-2 ENVIRONMENT EIA/JESD51-3 PCB TA = 25 C 3 2 0*1 1000 ITSM(t) APPLIED FOR TIME t 6 5 4 t - Current Duration - s 700 600 TC4HAA BELLCORE 2/10 500 0.99 0.97 '4070 THRU '4095 0.96 0.95 IEC 1.2/50, 8/20 300 FCC 10/160 250 ITU-T 10/700 200 FCC 10/560 150 '4125 THRU '4220 0.94 120 BELLCORE 10/1000 '4240 THRU '4440 0.93 -40 -35 -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 TAMIN - Minimum Ambient Temperature - C Figure 10. PRODUCT Impulse Current - A 400 0.98 Derating Factor TI4HAG 150 Z ITSM(t) - Non-Repetitive Peak On-State Current - A NON-REPETITIVE PEAK ON-STATE CURRENT vs CURRENT DURATION TI4HAH 100 90 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 TA - Ambient Temperature - C Figure 11. INFORMATION 7 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 APPLICATIONS INFORMATION deployment These devices are two terminal overvoltage protectors. They may be used either singly to limit the voltage between two conductors (Figure 12) or in multiples to limit the voltage at several points in a circuit (Figure 13). Th3 Th1 Th1 Th2 Figure 12. TWO POINT PROTECTION Figure 13. MULTI-POINT PROTECTION In Figure 12, protector Th1 limits the maximum voltage between the two conductors to V(BO). This configuration is normally used to protect circuits without a ground reference, such as modems. In Figure 13, protectors Th2 and Th3 limit the maximum voltage between each conductor and ground to the V(BO) of the individual protector. Protector Th1 limits the maximum voltage between the two conductors to its V(BO) value. If the equipment being protected has all its vulnerable components connected between the conductors and ground, then protector Th1 is not required. impulse testing To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms. The table below shows some common values. STANDARD GR-1089-CORE PEAK VOLTAGE VOLTAGE PEAK CURRENT CURRENT TISP4xxxH3 SERIES SETTING WAVE FORM VALUE WAVE FORM 25 C RATING RESISTANCE V s A s A 2500 2/10 500 2/10 500 1000 10/1000 100 10/1000 100 0 1500 10/160 200 10/160 250 0 FCC Part 68 800 10/560 100 10/560 160 0 (March 1998) 1500 9/720 37.5 5/320 200 0 1000 9/720 25 5/320 200 0 1500 0.5/700 37.5 0.2/310 200 0 5/310 200 0 I3124 ITU-T K20/K21 1500 4000 10/700 37.5 100 FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K21 10/700 impulse generator If the impulse generator current exceeds the protectors current rating then a series resistance can be used to reduce the current to the protectors rated value and so prevent possible failure. The required value of series resistance for a given waveform is given by the following calculations. First, the minimum total circuit impedance is found by dividing the impulse generators peak voltage by the protectors rated current. The impulse generators fictive impedance (generators peak voltage divided by peak short circuit current) is then subtracted from the minimum total circuit impedance to give the required value of series resistance. In some cases the equipment will require verification over a temperature range. By using the rated waveform values from Figure 11, the appropriate series resistor value can be calculated for ambient temperatures in the range of -40 C to 85 C. PRODUCT 8 INFORMATION TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 a.c. power testing The protector can withstand currents applied for times not exceeding those shown in Figure 8. Currents that exceed these times must be terminated or reduced to avoid protector failure. Fuses, PTC (Positive Temperature Coefficient) resistors and fusible resistors are overcurrent protection devices which can be used to reduce the current flow. Protective fuses may range from a few hundred milliamperes to one ampere. In some cases it may be necessary to add some extra series resistance to prevent the fuse opening during impulse testing. The current versus time characteristic of the overcurrent protector must be below the line shown in Figure 8. In some cases there may be a further time limit imposed by the test standard (e.g. UL 1459 wiring simulator failure). capacitance The protector characteristic off-state capacitance values are given for d.c. bias voltage, VD, values of 0, -1 V, -2 V and -50 V. Where possible values are also given for -100 V. Values for other voltages may be calculated by multiplying the VD = 0 capacitance value by the factor given in Figure 6. Up to 10 MHz the capacitance is essentially independent of frequency. Above 10 MHz the effective capacitance is strongly dependent on connection inductance. In many applications, such as Figure 15 and Figure 17, the typical conductor bias voltages will be about -2 V and -50 V. Figure 7 shows the differential (line unbalance) capacitance caused by biasing one protector at -2 V and the other at -50 V. normal system voltage levels The protector should not clip or limit the voltages that occur in normal system operation. For unusual conditions, such as ringing without the line connected, some degree of clipping is permissible. Under this condition about 10 V of clipping is normally possible without activating the ring trip circuit. Figure 10 allows the calculation of the protector VDRM value at temperatures below 25 C. The calculated value should not be less than the maximum normal system voltages. The TISP4260H3LM, with a VDRM of 200 V, can be used for the protection of ring generators producing 100 V rms of ring on a battery voltage of -58 V (Th2 and Th3 in Figure 17). The peak ring voltage will be 58 + 1.414*100 = 199.4 V. However, this is the open circuit voltage and the connection of the line and its equipment will reduce the peak voltage. In the extreme case of an unconnected line, clipping the peak voltage to 190 V should not activate the ring trip. This level of clipping would occur at the temperature when the VDRM has reduced to 190/200 = 0.95 of its 25 C value. Figure 10 shows that this condition will occur at an ambient temperature of -22 C. In this example, the TISP4260H3LM will allow normal equipment operation provided that the minimum expected ambient temperature does not fall below -22 C. JESD51 thermal measurement method To standardise thermal measurements, the EIA (Electronic Industries Alliance) has created the JESD51 standard. Part 2 of the standard (JESD51-2, 1995) describes the test environment. This is a 0.0283 m3 (1 ft3) cube which contains the test PCB (Printed Circuit Board) horizontally mounted at the centre. Part 3 of the standard (JESD51-3, 1996) defines two test PCBs for surface mount components; one for packages smaller than 27 mm on a side and the other for packages up to 48 mm. The LM package measurements used the smaller 76.2 mm x 114.3 mm (3.0 " x 4.5 ") PCB. The JESD51-3 PCBs are designed to have low effective thermal conductivity (high thermal resistance) and represent a worse case condition. The PCBs used in the majority of applications will achieve lower values of thermal resistance and so can dissipate higher power levels than indicated by the JESD51 values. PRODUCT INFORMATION 9 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 typical circuits TIP WIRE MODEM FUSE TIP WIRE RING DETECTOR R1a Th3 HOOK SWITCH TISP4350 OR TISP4400 RING WIRE PROTECTED EQUIPMENT Th1 D.C. SINK Th2 SIGNAL AI6XBM RING WIRE Figure 14. MODEM INTER-WIRE PROTECTION E.G. LINE CARD R1b AI6XBK Figure 15. PROTECTION MODULE R1a Th3 SIGNAL Th1 Th2 R1b AI6XBL D.C. Figure 16. ISDN PROTECTION OVERCURRENT PROTECTION TIP WIRE RING/TEST PROTECTION TEST RELAY RING RELAY SLIC RELAY S3a R1a Th3 S1a SLIC PROTECTION Th4 S2a SLIC Th1 Th2 RING WIRE Th5 R1b S3b S1b S2b TISP6xxxx, TISPPBLx, 1/2TISP6NTP2 C1 220 nF TEST EQUIPMENT RING GENERATOR Figure 17. LINE CARD RING/TEST PROTECTION PRODUCT 10 INFORMATION VBAT AI6XBJ TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 MECHANICAL DATA device symbolization code Devices will be coded as below. DEVICE SYMOBLIZATION CODE TISP4070H3 4070H3 TISP4080H3 4080H3 TISP4095H3 4095H3 TISP4125H3 4125H3 TISP4145H3 4145H3 TISP4165H3 4165H3 TISP4180H3 4180H3 TISP4220H3 4220H3 TISP4240H3 4240H3 TISP4260H3 4260H3 TISP4300H3 4300H3 TISP4350H3 4350H3 TISP4400H3 4400H3 carrier information Devices are shipped in one of the carriers below. A reel contains 2 000 devices. PRODUCT PACKAGE TYPE CARRIER Straight Lead DO-92 Bulk Pack ORDER # TISP4xxxH3LM Straight Lead DO-92 Tape and Reeled TISP4xxxH3LMR Formed Lead DO-92 Tape and Reeled TISP4xxxH3LMFR INFORMATION 11 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 MECHANICAL DATA LM002 (DO-92) 2-pin cylindrical plastic package This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. . LM002 Package (DO-92) 5,21 4,44 3,43 MIN. 4,19 3,17 2,67 2,03 2,67 2,03 5,34 4,32 2,20 MAX. A 2 2 12,7 MIN. 0,56 0,40 1 3 3 1 VIEW A 0,41 0,35 1,40 1,14 2,67 2,41 ALL LINEAR DIMENSIONS IN MILLIMETERS MD4XARA PRODUCT 12 INFORMATION TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 MECHANICAL DATA LM002 (DO-92) - Formed Leads Version 2-pin cylindrical plastic package This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. LMF002 (DO-92) - Formed Leads Version of LM002 5,21 4,44 3,43 MIN. 4,19 3,17 2,67 2,03 2,67 2,03 5,34 4,32 2,20 MAX. 4,00 MAX. A 2 2 0,56 0,40 1 3 3 1 VIEW A 2,90 2,40 0,41 0,35 2,90 2,40 ALL LINEAR DIMENSIONS IN MILLIMETERS MD4XASA PRODUCT INFORMATION 13 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 MECHANICAL DATA tape dimensions LM002 Package (Straight Lead DO-92) Tape LM002 Tape Dimensions Conform to the Requirements of EIA-468-B 13,70 11,70 Body Indent Visible 32,00 23,00 0,50 0,00 2,50 MIN. 27,68 17,66 11,00 8,50 9,75 8,50 3,14 2,14 19,00 5,50 19,00 17,50 4,30 Adhesive Tape on Reverse Side - Shown Dashed VIEW A 3,70 5,48 4,68 13,00 12,40 Tape Section Shown in View A Flat of DO-92 Body Towards Reel Axis Direction of Feed ALL LINEAR DIMENSIONS IN MILLIMETERS MD4XAPC PRODUCT 14 INFORMATION TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 MECHANICAL DATA tape dimensions LMF002 Package (Formed Lead DO-92) Tape LMF002 Tape Dimensions Conform to the Requirements of EIA-468-B 13,70 11,70 Body Indent Visible 32,00 23,00 27,68 17,66 0,50 0,00 2,50 MIN. 16,53 15,50 11,00 8,50 9,75 8,50 5,28 4,88 Adhesive Tape on Reverse Side - Shown Dashed 19,00 5,50 19,00 17,50 4,30 3,70 VIEW A 4,21 3,41 13,00 12,40 Tape Section Shown in View A Flat of DO-92 Body Towards Reel Axis Direction of Feed ALL LINEAR DIMENSIONS IN MILLIMETERS MD4XAQC PRODUCT INFORMATION 15 TISP4070H3LM THRU TISP4095H3LM, TISP4125H3LM THRU TISP4220H3LM, TISP4240H3LM THRU TISP4400H3LM BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS NOVEMBER 1997 - REVISED APRIL 1999 IMPORTANT NOTICE Power Innovations Limited (PI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to verify, before placing orders, that the information being relied on is current. PI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with PI's standard warranty. Testing and other quality control techniques are utilized to the extent PI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. PI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor is any license, either express or implied, granted under any patent right, copyright, design right, or other intellectual property right of PI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. PI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORISED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS. Copyright (c) 1999, Power Innovations Limited PRODUCT 16 INFORMATION